ON Semiconductor
Is Now
To learn more about onsemi™, please visit our website at
www.onsemi.com
onsemi and and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or
subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi
product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without
notice. The information herein is provided “as-is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality,
or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws,
regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/
or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application
by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized
for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for
implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative
Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. Other names and brands may be claimed as the property of others.
FUSB302B
FUSB302B Programmable
USB Type‐C Controller w/PD
Description
The FUSB302B targets system designers looking to implement
a DRP/SRC/SNK USB Type-C connector with low amount of
programmability.
The FUSB302B enables the USB Type-C detection including
attach, and orientation. The FUSB302B integrates the physical layer
of the USB BMC power delivery protocol to allow up to 100 W of
power and role swap. The BMC PD block enables full support for
alternative interfaces of the Type-C specification.
www.onsemi.com
WLCSP9
CASE 567TN
Features
• Dual-role Functionality with Autonomous DRP Toggle
• Ability to Connect as Either a Host or a Device Based on What Has
•
•
•
•
•
•
•
•
Been Attached
Software Configurable Either as a Dedicated Host, Dedicated
Device, or Dual Role
♦ Dedicated Devices can Operate both on a Type-C Receptacle or
a Type-C Plug with a Fixed CC and VCONN Channel
Full Type-C 1.2 Support. Integrates the Following Functionality of
the CC Pin:
♦ Attach/Detach Detection as Host
♦ Current Capability Indication as Host
♦ Current Capability Detection as Device
♦ Audio Adapter Accessory Mode
♦ Debug Accessory Mode
♦ Active Cable Detection
Integrates CCx to VCONN Switch with Over-current Limiting for
Powering USB3.1 Full Featured Cables
USB Power Delivery (PD) 2.0, Version 1.2 Support:
♦ Automatic GoodCRC Packet Response
♦ Automatic Retries of Sending a Packet if a GoodCRC is Not
Received
♦ Automatic Soft Reset Packet Sent with Retries if Needed
♦ Automatic Hard Reset Ordered Set Sent
Dead Battery Support (SNK Mode Support when No Power Applied)
Low Power Operation: ICC = 25 mA (Typical)
AEC−Q100 Automotive Qualified Temperature Grade 2:
(−40°C to +105°C)
Packaged in:
♦ 9-ball WLCSP (1.215 mm × 1.260 mm)
♦ 14-lead MLP (2.5 mm × 2.5 mm, 0.5 mm Pitch)
Applications
•
•
•
•
•
•
•
•
Smartphones
Tablets
Laptops
Notebooks
© Semiconductor Components Industries, LLC, 2015
November, 2017 − Rev. 4
1
WQFN14
CASE 510BR
ORDERING INFORMATION
See detailed ordering and shipping information on page 2 of
this data sheet.
Power Adapters
Cameras
Dongles
Automotive
Publication Order Number:
FUSB302B/D
FUSB302B
Charger
OVP
USB Type-C
Connector
VBUS
VCONN
FUSB302
CC1
USB Type-C
Detection
Control PD
I2Ct
CC2
Processor
USB Switch
TX1/RX1
USB 3.1
TX2/RX2
5Gbps
Figure 1. Block Diagram
Table 1. ORDERING INFORMATION
Part Number
Top Mark
FUSB302BUCX
H4
FUSB302BMPX
UA
FUSB302B01MPX
UP
FUSB302B10MPX
US
FUSB302B11MPX
UT
FUSB302BVMPX
DA
Operating
Temperature Range
Package
Shipping†
9-ball Wafer-level Chip Scale
Package (WLCSP), 0.4 mm Pitch
−40 to 85°C
−40 to 85°C
14-lead MLP 2.5 mm × 2.5 mm,
0.5 mm Pitch
3,000 / Tape and Reel
−40 to 105°C
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
2
FUSB302B
TYPICAL APPLICATION
BAT
CHARGER
OVP
3.0V
REG
VBUS
1.71V to V
VCONN
VDD
FUSB302B
TYPE−C
I2C/
Registers
VBUS
GND
RX2+ TX2+
RX2− TX2−
VBUS
SBU1
CC2
D−
D+
D+
D−
CC1
SBU2
VBUS
TX1− RX1−
TX1+ RX1+
GND
CC 2
Dual−Role Detection
Auto Toggle
CC 1
Switch Matrix
CC Detection / Control
Powered Cable
Audio Adapter / Debug Acc
BMC I/O
INT_N
I2C_SDA
I2C_SCL
Logic &
Control
Processor
DAC Comparator
GND
GND
USB_3.1
1
FUSB340
USB 3.1
2:1 Switch
USB_3.1
2
Figure 2. Typical Application
BLOCK DIAGRAM
VCONN
VBUS
CC1
FUSB302B
Processor (Software)
Type−C Connection States
− SOURCE
− SINK
− SINK with Accessory
Support
− Dual−Role Port
− Dual−Role Port with
Accessory Support
Control
Settings
:
Comp.
Status
RD
CC2
Type−C
Switch
Settings
DAC
INT_N
SDA
2
I C Reg
SCL
PD (Provider/Consumer)
Device Policy Manager
PD/
VDM
PD
Configuration
PD Status
RD
Code/
Control
Logic
Protocol
FIFO
CRC32
Tx
FIFO
CRC32
Rx
FIFO
Access
4B5B
BMC
DRIVER
Policy Engine
BMC
BMC Physical Layer
4B5B
Figure 3. Functional Block Diagram
www.onsemi.com
3
BMC
CDR
FUSB302B
PIN CONFIGURATION
1 2 3
A
B
C
3 2 1
CC2
VBUS
VDD
VDD
VBUS
CC2
VCONN
INT_N
SCL
SCL
INT_N
VCONN
CC1
GND
SDA
SDA
GND
CC1
TOP Through View
A
B
C
Bottom view
Figure 4. FUSB302BUCX Pin Assignment
Table 2. PIN MAP
Column 1
Column 2
Column 3
Row A
CC2
VBUS
VDD
Row B
VCONN
INT_N
SCL
Row C
CC1
GND
SDA
www.onsemi.com
4
FUSB302B
14
CC2
13
VCONN
12
VCONN
11
CC1
11
CC1
1
CC2
TOP
THROUGH
VIEW
2
VBUS
Connect to GND for
Thermal
3
VDD
4
VDD
5
INT_N
6
SCL
10
CC1
10
CC1
9
GND
9
GND
8
GND
8
GND
7
SDA
12
VCONN
13
VCONN
14
CC2
1
CC2
BOTTOM
VIEW
2
VBUS
Connect to GND for
Thermal
7
SDA
6
SCL
5
INT_N
3
VDD
4
VDD
Figure 5. FUSB302BMPX Pin Assignment (N/C = No Connect)
Table 3. PIN DESCRIPTION
Name
Type
Description
USB TYPE-C CONNECTOR INTERFACE
CC1/CC2
I/O
GND
Ground
VBUS
Input
Type-C connector Configuration Channel (CC) pins. Initially used to determine when an attach has
occurred and what the orientation of the insertion is. Functionality after attach depends on mode of
operation detected.
Operating as a host:
1. Sets the allowable charging current for VBUS to be sensed by the attached device
2. Used to communicate with devices using USB BMC Power Delivery
3. Used to detect when a detach has occurred
Operating as a device:
1. Indicates what the allowable sink current is from the attached host. Used to communicate with
devices using USB BMC Power Delivery
Ground
VBUS input pin for attach and detach detection when operating as an upstream facing port
(Device). Expected to be an OVP protected input.
POWER INTERFACE
VDD
Power
VCONN
Power Switch
Input supply voltage.
Regulated input to be switched to correct CC pin as VCONN to power USB3.1 full-featured cables
and other accessories.
SIGNAL INTERFACE
SCL
Input
I2C serial clock signal to be connected to the phone-based I2C master.
SDA
Open-Drain I/O
I2C serial data signal to be connected to the phone-based I2C master
INT_N
Open-Drain
Output
Active LOW open drain interrupt output used to prompt the processor to read the I2C register bits
www.onsemi.com
5
FUSB302B
CONFIGURATION CHANNEL SWITCH
• USB BMC Power Delivery Physical Layer
• Configuration Channel (CC) Threshold Comparators
The FUSB302B integrates the control and detection
functionality required to implement a USB Type-C host,
device or dual-role port including:
• Device Port Pull-Down (RD)
• Host Port Pull-Up (IP)
• VCONN Power Switch with OCP for Full-Featured
USB3.1 Cables
Each CC pin contains a flexible switch matrix that allows
the host software to control what type of Type-C port is
implemented. The switches are shown in Figure 6.
CCX
VCONN
VCONN_SWITCH
VCONN_CCx
Reg
MEAS_CCx
Reg
DAC/
Comparator
MEAS_CC_SWITCH
TXCCx
Reg
BMC
I/O
TX_BMC_SWITCH
PU_ENx
Reg
Current
Source
Pull−ups
PWDNx
Reg
PULLUP_SWITCH
PULLDOWN_SWITCH
5.1K
Figure 6. Configuration Channel Switch Functionality
TYPE-C DETECTION
The FUSB302B also has a fixed comparator that monitors
if VBUS has reached a valid threshold or not. The DAC can
be used to measure VBUS up to 20 V which allows the
software to confirm that changes to the VBUS line have
occurred as expected based on PD or other communication
methods to change the charging level.
The FUSB302B implements multiple comparators and
a programmable DAC that can be used by software to
determine the state of the CC and VBUS pins. This status
information provides the processor all of the information
required to determine attach, detach and charging current
configuration of the Type-C port connection.
The FUSB302B has three fixed threshold comparators
that match the USB Type-C specification for the three
charging current levels that can be detected by a Type-C
device. These comparators automatically cause BC_LVL
and COMP interrupts to occur when there is a change of
state. In addition to the fixed threshold comparators, the host
software can use the 6-bit DAC to determine the state of the
CC lines more accurately.
Detection through Autonomous Device Toggle
The FUSB302B has the capability to do autonomous DRP
toggle. In autonomous toggle the FUSB302B internally
controls the PDWN1, PDWN2, PU_EN1 and PU_EN2,
MEAS_CC1 and MEAS_CC2 and implements a fixed DRP
toggle between presenting as a SRC and presenting as
a SNK. Alternately, it can present as a SRC or SNK only and
poll CC1 and CC2 continuously.
www.onsemi.com
6
FUSB302B
Manual Device Detection and Configuration
Table 4. PROCESSOR CONFIGURES THE
FUSB302B THROUGH I2C
I2C Registers/Bits
A Type-C device must monitor VBUS to determine if it is
attached or detached. The FUSB302B provides this
information through the VBUSOK interrupt. After the
Type-C device knows that a Type-C host has been attached,
it needs to determine what type of termination is applied to
each CC pin. The software determines if an Ra or Rd
termination is present based on the BC_LVL and COMP
interrupt and status bits.
Additionally, for Rd terminations, the software can
further determine what charging current is allowed by the
Type-C host by reading the BC_LVL status bits. This is
summarized in Table 5.
Value
TOGGLE
1
PWR
07H
HOST_CUR0
1
HOST_CUR1
0
MEAS_VBUS
0
VCONN_CC1
0
VCONN_CC2
0
Mask Register
0xFE
Maska Register
0xBF
Maskb Register
(Except I_TOGDONE and I_BC_LVL Interrupt)
0x01
PWR[3:0]
0xBF
Toggle Functionality
When TOGGLE bit (Control2 register) is set the
FUSB302B implements a fixed DRP toggle between
presenting as a SRC and as a SNK. It can also be configured
to present as a SRC only or SNK only and poll CC1 and CC2
continuously. This operation is turned on with TOGGLE = 1
and the processor should initially write HOST_CUR1 = 0,
HOST_CUR0 = 1 (for default current), VCONN_CC1 =
VCONN_CC2 = 0, Mask Register = 0xFE, Maska
register = 0xBF, and Maskb register = 0x01, and PWR =
0x01. The processor should also read the interrupt register
to clear them prior to setting the TOGGLE bit.
1. Once it has been determined what the role is of the FUSB302B,
it returns I_TOGDONE and TOGSS1/2.
2. Processor then can perform a final manual check through I2C.
Manual Device Toggle
The FUSB302B has the capability to do manual DRP
toggle. In manual toggle the FUSB302B is configurable by
the processor software by I2C and setting TOGGLE = 0.
Table 5. DEVICE INTERRUPT SUMMARY
Interrupt Status
Status Type
BC_LVL[1:0]
COMP
COMP Setting
VBUSOK
Meaning
CC Detection
2’b00
NA
NA
1
vRA
2’b01
NA
NA
1
vRd−Connect and vRd−USB
2’b10
NA
NA
1
vRd−Connect and vRd−1.5
2’b11
0
6’b11_0100
(2.05 V)
1
vRd−Connect and vRd−3.0
Attach
NA
NA
NA
1
Host Attached, VBUS Valid
Detach
NA
NA
NA
0
Host Detached, VBUS Invalid
The high level software flow diagram for a Type-C device
(SNK) is shown in Figure 7.
www.onsemi.com
7
FUSB302B
Disabled:
FUSB302B in low power
mode looking for an attach
FUSB302B I_TOGDONE
interrupt alerts host
software that something
has attached.
Unattached.SNK:
Host software enables
FUSB302B pull−downs
and measure block to
detect attach
FUSB302B I_VBUSOK interrupt
alerts host software that an attach
has occurred
FUSB302B I_VBUSOK interrupt
alerts host software that a detach has
occurred
Attached.SNK
Host software uses FUSB302B
comparators and DAC to determine
attach orientation and port type
Host software determines that an
accessory has been attached
DebugAccessory
AudioAccessory
FUSB302B I_COMP and I_VBUSOK
interrupts alert host software that a
accessory detach has occurred
Figure 7. SNK Software Flow
Manual Host Detection and Configuration
HOST_CUR control bits. If the HOST_CUR bits are
changed prior to attach, the FUSB302B automatically
indicates the programmed current capability when a device
is attached. If the current capabilities are changed after
a device is attached, the FUSB302B immediately changes
the CC line to the programmed capability.
When the FUSB302B is configured as a Type-C host, the
software can use the status of the comparators and DAC to
determine when a Type-C device has been attached or
detached and what termination type has been attached to
each CC pin.
The FUSB302B allows the host software to change the
charging current capabilities of the port through the
ATTACH
CC
0V
HOST_CUR[1:0] = DEFAULT
HIGH CURRENT SETTING
Figure 8. HOST_CUR Changed after Attach
www.onsemi.com
8
MED CURRENT SETTING
FUSB302B
ATTACH
CC
0V
HIGH CURRENT SETTING
MED CURRENT SETTING
DEFAULT CURRENT
Figure 9. HOST_CUR Changed prior to Attach
DAC comparator threshold to match the Type-C
specification requirements. The BC_LVL comparators can
also be used as part of the Ra detection flow. This is
summarized in Table 6.
The Type-C specification outlines different attach and
detach thresholds for a Type-C host that are based on how
much current is supplied to each CC pin. Based on the
programmed HOST_CUR setting, the software adjusts the
Table 6. HOST INTERRUPT SUMMARY
Interrupt Status
Termination
HOST_CUR[1:0]
BC_LVL[1:0]
COMP
COMP Setting
Attach/Detach
Ra
2’b01
2’b00
NA
NA
NA
2’b10
2’b01
0
6’b00_1010 (0.42 V)
2’b11
2’b10
0
6’b01_0011 (0.8 V)
2’b01, 2’b10
NA
0
6’b10_0110 (1.6 V)
Attach
NA
1
6’b10_0110 (1.6 V)
Detach
NA
0
6’b11_1110 (2.6 V)
Attach
NA
1
6’b11_1110 (2.6 V)
Detach
Rd
2’b11
The high level software flow diagram for a Type-C Host
(SRC) is shown below in Figure 10.
www.onsemi.com
9
FUSB302B
Disabled:
FUSB302B in low power
mode looking for an attach
FUSB302B I_TOGDONE
interrupt alerts host
software that something
has attached.
Unattached.SRC:
Host software enables
FUSB302B pull−ups and
measure block to detect
attach
Host software utilizes I_COMP and
I_BC_LVL interrupts to determine an
attach and what type of port is attached.
FUSB302B I_COMP interrupt alerts
host software that a detach has
occurred
Attached.SRC
Host software configures
FUSB302B based on insertion
orientation and enables VBUS
and VCONN
AudioAccessory
DebugAccessory
FUSB302B I_COMP and I_VBUSOK
interrupts alert host software that a
accessory detach has occurred
Figure 10. SRC Software Flow
Manual Dual-Role Detection and Configuration
FUSB302B can be used to implement a dual-role port.
A Type-C dual role port toggles between presenting as
a Type-C device and a Type-C host. The host software
controls the toggle time and configuration of the FUSB302B
in each state as shown in Figure 11.
The Type-C specification allows ports to be both a device
and a host depending on what type of port has attached. This
functionality is similar to USB OTG ports with the current
USB connectors and is called a dual-role port. The
Disabled:
FUSB302B in low power
mode looking for an attach
FUSB302B I_TOGONE
interrupt alerts host
software that something
has attached.
Host software enables
FUSB302B low power
Disabled state
Unattached.SNK:
Host software enables
FUSB302B pull−downs
and measure block to
detect attach
FUSB302B I_VBUSOK interrupt
alerts host software that a detach has
occurred
Host software toggle
expires
FUSB302B I_VBUSOK interrupt
alerts host software that an attach
has occurred
Unattached.SRC:
Host software enables
FUSB302B pull−ups and
measure block to detect
attach
Host software utilizes I_COMP and
I_BC_LVL interrupts to determine an
attach
Attached.SRC
Host software configures
FUSB302B based on insertion
orientation and enables VBUS
and VCONN
Attached.SNK
Host software uses FUSB302B
comparators and DAC to
determine attach orientation and
port type
Figure 11. DRP Software Flow
www.onsemi.com
10
FUSB302B I_COMP interrupt alerts
host software that a detach has
occurred
FUSB302B
BMC POWER DELIVERY
The Type-C connector allows USB Power Delivery (PD)
to be communicated over the connected CC pin between two
ports. The communication method is the BMC Power
Delivery protocol and is used for many different reasons
with the Type-C connector. Possible uses are outlined below.
• Negotiating and controlling charging power levels
• Alternative Interfaces such as MHL, Display Port
• Vendor specific interfaces for use with custom docks or
accessories
• Role swap for dual-role ports that want to switch who is
the host or device
• Communication with USB3.1 full featured cables
reads of the FIFO and control of the FUSB302B physical
interface.
The FUSB302B uses tokens to control the transmission of
BMC PD packets. These tokens are written to the transmit
FIFO and control how the packet is transmitted on the CC
pin. The tokens are designed to be flexible and support all
aspects of the USB PD specification. The FUSB302B
additionally enables control of the BMC transmitter through
tokens. The transmitter can be enabled or disabled by
specific token writes which allow faster packet processing
by burst writing the FIFO with all the information required
to transmit a packet.
The FUSB302B receiver stores the received data and the
received CRC in the receive FIFO when a valid packet is
received on the CC pin. The BMC receiver automatically
enables the internal oscillator when an Activity is sensed on
the CC pin and load to the FIFO when a packet is received.
The I_ACTIVITY and I_CRC_CHK interrupts alert the
host software that a valid packet was received.
The FUSB302B integrates a thin BMC PD client which
includes the BMC physical layer and packet FIFOs (48 bytes
for transmit and 80 bytes for receive) which allows packets
to be sent and received by the host software through I2C
accesses. The FUSB302B allows host software to
implement all features of USB BMC PD through writes and
Code/
Control
Logic
4B5B
BMC
DRIVER
FIFO
CRC32
Tx
BMC
CC1
CC2
FIFO
CRC32
Rx
4B5B
BMC
CDR
Figure 12. USB BMC Power Delivery Blocks
Power Level Determination
If no power applied to VDD then the SRC can recognize
the FUSB302B as a SNK.
The Type-C specification outlines the order of precedence
for power level determination which covers power levels
from basic USB2.0 levels to the highest levels of USB PD.
The host software is expected to follow the USB Type-C
specification for charging current priority based on feedback
from the FUSB302B detection, external BC1.2 detection
and any USB Power Delivery communication.
The FUSB302B does not integrate BC1.2 charger
detection which is assumed available in the USB transceiver
or USB charger in the system.
PD Automatic Receive GoodCRC
The power delivery packets require a GoodCRC
acknowledge packet to be sent for each received packet
where the calculated CRC is the correct value. This
calculation is done by the FUSB302B and triggers the
I_CRC_CHK interrupt if the CRC is good. If the
AUTO_CRC (Switches1 register bit) is set and
AUTO_PRE = 0, then the FUSB302B will automatically
send the GoodCRC control packet in response to alleviate
the local processor from responding quickly to the received
packet. If GoodCRC is required for anything beyond SOP,
then enable SOP*.
Power Up, Initialization and Reset
When power is first applied through VDD, the
FUSB302B is reset and registers are initialized to the default
values shown in the register map.
The FUSB302B can be reset through software by
programming the SW_RES bit in the RESET register.
www.onsemi.com
11
FUSB302B
PD Send
The FUSB302B implements part of the PD protocol layer
for sending packets in an autonomous fashion.
PD Packet
Sent
Automatic
Sending Retries
Soft Reset
Hard
Reset
Figure 13.
PD Automatic Sending Retries
hard reset is sent since the typical retry mechanism doesn’t
apply. The processor’s policy engine firmware is
responsible for retrying the hard reset if it doesn’t receive the
required response.
If GoodCRC packet is not received and AUTO_RETRY
is set, then a retry of the same message that was in the
TxFIFO written by the processor is executed within tRetry
and that is repeated for NRETRY times.
Flush Rx-FIFO with BIST (Built-In Self Test) Test Data
PD Send Soft Reset
During PD compliance testing, BIST test packets are used
to test physical layer of the PD interface such as, frequency
derivation, Amplitude measure and etc. The one BIST test
data packet has 7 data objects (28byte data), header and
CRC, but the message ID doesn’t change, the packet should
be ignored and not acted on by the PD policy engine. The PD
protocol layer does need to send a GoodCRC message back
after every packet. The BIST data can arrive continuously
from a tester, which could cause the FUSB302B Rx FIFO to
overflow and the PD protocol layer to stop sending
GoodCRC messages unless the FIFO is read or cleared
quickly. The FUSB302B has a special register bit in the I2C
registers, bit[5] of address 0x09, that when the bit is set, all
the data received next will be flushed from the RxFIFO
automatically and the PD protocol layer will keep sending
GoodCRC messages back. Once BIST test is done, tester
sends HardReset, so with the HardReset, processor has to
write the bit back to disable. Also, if the bit can be
de-selected anytime, then the coming packet has to be
managed by protocol layer and policy engine.
If the correct GoodCRC packet is still not received for all
retries then I_RETRYFAIL interrupt is triggered and if
AUTO_SOFT_RESET is set, then a Soft Reset packet is
created (MessageID is set to 0 and the processor upon
servicing I_RETRYFAIL would set the true
MessageIDCounter to 0.
If this Soft Reset is sent successfully where a GoodCRC
control packet is received with a MessageID = 0 then
I_TXSENT interrupt occurs.
If not, this Soft Reset packet is retried NRETRIES times
(MessageID is always 0 for all retries) if a GoodCRC
acknowledge packet is not received with CRCReceiveTimer
expiring (tReceive of 1.1 ms max). If all retries fail, then
I_SOFTFAIL interrupt is triggered.
PD Send Hard Reset
If all retries of the soft reset packet fail and if
AUTO_HARD_RESET is set, then a hard reset ordered set
is sent by loading up the TxFIFO with RESET1, RESET1,
RESET1, RESET2 and sending a hard reset. Note only one
I2C INTERFACE
The FUSB302B includes a full I2C slave controller. The
slave fully complies with the I2C specification version
6 requieremnts. This block is designed for Fast Mode Plus
traffic up to 1 MHz SCL operation.
The TOGGLE features allow for very low power
operation with slow clocking thus may not be fully
compliant to the 1 MHz operation. Examples of an I2C write
and read sequence are shown in Figure 14 and Figure 15
respectively.
I2 C
8bits
8bits
8bits
S Slave Address WR A Register Address K A Write Data A Write Data K+1 A Write Data K+2 A
Note:
Single Byte read is initiated by Master with P immediately following first data byte
Figure 14. I2C Write Example
www.onsemi.com
12
Write Data K+N−1
AP
FUSB302B
8bits
8bits
8bits
S Slave Address WR A Register Address K A S
Slave Address RD A
Read Data K A Read Data K+1 A Read Data K+N-1 NA P
Single or multi byte read executed from current register location (Single Byte read is
initiated by Master with NA immediately following first data byte)
Register address to Read specified
Note:
8bits
If Register is not specified Master will begin read from current register. In this case only sequence showing in Red
bracket is needed
S
A
From Master to Slave
From Slave to Master
Start Condition
Acknowledge (SDA Low)
NA NOT Acknowledge (SDA High)
WR Write=0
RD
P
Read =1
Stop Condition
Figure 15. I2C Read Example
Table 7. ABSOLUTE MAXIMUM RATINGS
Symbol
VvDD
VCC_HDDRP
VVBUS
TSTORAGE
Parameter
Min
Max
Unit
Supply Voltage from VDD
−0.5
6.0
V
CC pins when configured as Host, Device or Dual Role Port
−0.5
6.0
V
VBUS Supply Voltage
−0.5
28.0
V
Storage Temperature Range
−65
+150
°C
TJ
Maximum Junction Temperature
−
+150
°C
TL
Lead Temperature (Soldering, 10 Seconds)
−
+260
°C
Human Body Model, ANSI/ESDA/JEDEC JS−001−2012
4
−
kV
Charged Device Model, JEDEC JESD22−C101
1
−
ESD
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Table 8. RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
VVBUS
VBUS Supply Voltage
VVDD
VDD Supply Voltage
Min
Typ
Max
Unit
4.0
5.0
21.0
V
2.7 (Note 3)
3.3
5.5
V
VVCONN
VCONN Supply Voltage
2.7
−
5.5
V
IVCONN
VCONN Supply Current
−
−
560
mA
TA
Operating Temperature
−40
−
+85
°C
TA
Operating Temperature (Note 11)
−40
−
+105
°C
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
3. This is for functional operation only and not the lowest limit for all subsequent electrical specifications below. All electrical parameters have
a minimum of 3.0 V operation.
www.onsemi.com
13
FUSB302B
DC AND TRANSIENT CHARACTERISTICS
All typical values are at TA = 25°C unless otherwise specified.
Table 9. BASEBAND PD
TA = −40 to +855C
TA = −40 to +1055C (Note 11)
TJ = −40 to +1255C
Symbol
UI
Parameter
Unit Interval
Min
Typ
Max
Unit
3.03
−
3.70
ms
TRANSMITTER
Transmitter Output Impedance
33
−
75
W
tEndDriveBMC
Time to Cease Driving the Line after the end of the last bit of the Frame
−
−
23
ms
tHoldLowBMC
Time to Cease Driving the Line after the final High-to-Low Transition
1
−
−
ms
zDriver
VOH
Logic High Voltage
1.05
−
1.20
V
VOL
Logic Low Voltage
0
−
75
mV
tStartDrive
Time before the start of the first bit of the preamble when the transmitter
shall start driving the line
−1
−
1
ms
tRISE_TX
Rise Time
300
−
−
ns
tFALL_TX
Fall Time
300
−
−
ns
RECEIVER
Receiver Capacitance when Driver isn’t Turned On
−
50
−
pF
zBmcRx
Receiver Input Impedance
1
−
−
MW
tRxFilter
Rx Bandwidth Limiting Filter (Note 4)
100
−
−
ns
cReceiver
4. Guaranteed by Characterization and/or Design. Not production tested.
DRP
Switch
Vconn
Switch
Vconn
Connector
Cable
Connector
Receiver
Receiver
cCablePlug
cCablePlug
Figure 16. Transmitter Test Load
www.onsemi.com
14
DRP
FUSB302B
Table 10. TYPE-C CC SWITCH
TA = −40 to +855C
TA = −40 to +1055C (Note 11)
TJ = −40 to +1255C
Min
Typ
Max
Unit
−
0.4
1.2
W
600
800
1000
mA
Time taken for the VCONN switch to turn on during which
Over-Current Protection is disabled
−
1.5
−
ms
I80_CCX
SRC 80 mA CC current (Default) HOST_CUR1 = 0, HOST_CUR0 = 1
64
80
96
mA
I180_CCX
SRC 180 mA CC Current (1.5 A) HOST_CUR1 = 1, HOST_CUR0 = 0
166
180
194
mA
I330_CCX
SRC 330 mA CC Current (3 A) HOST_CUR1 = 1, HOST_CUR0 = 1
304
330
356
mA
Symbol
Parameter
RSW_CCx
RDSON for SW1_CC1 and SW1_CC2, VCONN to CC1 & CC2
ISW_CCX
Over-Current Protection (OCP) limit at which VCONN switch shuts off
over the entire VCONN voltage range (OCPreg = 0Fh)
tSoftStart
VUFPDB
SNK Pull-down Voltage in Dead Battery under all Pull-up SRC Loads
−
−
2.18
V
RDEVICE
Device Pull-down Resistance (Note 5)
4.6
5.1
5.6
kW
zOPEN
CC Resistance for Disabled State
126
−
−
kW
WAKElow
Wake threshold for CC pin SRC or SNK LOW value. Assumes
bandgap and wake circuit turned on ie PWR[0] = 1
−
0.25
−
V
WAKEhigh
Wake threshold for CC pin SRC or SNK HIGH value. Assumes
bandgap and wake circuit turned on ie PWR[0] = 1
−
1.45
−
V
Hysteresis on the Ra and Rd Comparators (Note 7)
−
20
−
mV
0.15
0.61
1.16
0.20
0.66
1.23
0.25
0.70
1.31
vBC_LVLhys
vBC_LVL
CC Pin Thresholds, Assumes PWR = 4’h7
BC = 2’b00
BC = 2’b01
BC = 2’b10
V
vMDACstepCC
Measure block MDAC step size for each code in MDAC[5:0] register
−
42
−
mV
vMDACstepVBUS
Measure block MDAC step size for each code in MDAC[5:0] register
for VBUS measurement
−
420
−
mV
vVBUSthr
VBUS threshold at which I_VBUSOK interrupt is triggered. Assumes
measure block on ie PWR[2] = 1
−
−
4.0
V
tTOG1
When TOGGLE = 1, time at which internal versions of
PU_EN1 = PU_EN2 = 0 and PWDN1 = PDWN2 = 1 selected to
present externally as a SNK in the DRP toggle
30
45
60
ms
tTOG2
When TOGGLE = 1, time at which internal versions of PU_EN1 = 1
or PU_EN2 = 1 and PWDN1 = PDWN2 = 0 selected to present
externally as a SRC in the DRP toggle
20
40
ms
tDIS
Disable time after a full toggle (tTOG1 + tTOG2) cycle so as to save
power
TOG_SAVE_PWR2:1 = 00
TOG_SAVE_PWR2:1 = 01
TOG_SAVE_PWR2:1 = 10
TOG_SAVE_PWR2:1 = 11
−
−
−
−
0
40
80
160
−
−
−
−
Tshut
Temp. for Vconn Switch Off
−
145
−
°C
Thys
Temp. Hysteresis for Vconn Switch Turn On
−
10
−
°C
5. RDEVICE minimum and maximum specifications are only guaranteed when power is applied.
www.onsemi.com
15
30
ms
FUSB302B
Table 11. CURRENT CONSUMPTION
TA = −40 to +855C
TA = −40 to +1055C (Note 11)
TJ = −40 to +1255C
Symbol
Parameter
Min
Typ
Max
Unit
Idisable
Disabled Current
3.0 to 5.5
Nothing Attached,
No I2C Transactions
−
0.37
5.0
mA
Idisable
Disabled Current
(Note 11)
3.0 to 5.5
Nothing Attached,
No I2C Transactions
−
0.37
8.5
mA
Unattached (standby)
Toggle Current
3.0 to 5.5
Nothing attached,
TOGGLE = 1,
PWR[3:0] = 1h,
WAKE_EN = 0,
TOG_SAVE_PWR2:1 = 01
−
25
40
mA
BMC PD Standby
Current
3.0 to 5.5
Device Attached, BMC PD
Active But Not Sending or
Receiving Anything,
PWR[3:0] = 7h
−
40
−
mA
Itog
Ipd_stby_meas
VDD (V)
Conditions
Table 12. USB PD SPECIFIC PARAMETERS
TA = −40 to +855C
TA = −40 to +1055C (Note 11)
TJ = −40 to +1255C
Symbol
Parameter
Min
Typ
Max
Unit
tHardReset
If a Soft Reset message fails, a Hard Reset is sent after tHardReset of
CRCReceiveTimer expiring
−
−
5
ms
tHardReset
Complete
If the FUSB302B cannot send a Hard Reset within tHardResetComplete
time because of a busy line, then a I_HARDFAIL interrupt is triggered
−
−
5
ms
0.9
−
1.1
ms
tReceive
This is the value for which the CRCReceiveTimer expires.
The CRCReceiveTimer is started upon the last bit of the EOP of the
transmitted packet
tRetry
Once the CRCReceiveTimer expires, a retry packet has to be sent out
within tRetry time. This time is hard to separate externally from tReceive
since they both happen sequentially with no visible difference in the CC
output
−
−
75
ms
tSoftReset
If a GoodCRC packet is not received within tReceive for NRETRIES then
a Soft Reset packet is sent within tSoftReset time.
−
−
5
ms
tTransmit
From receiving a packet, we have to send a GoodCRC in response within
tTransmit time. It is measured from the last bit of the EOP of the received
packet to the first bit sent of the preamble of the GoodCRC packet
−
−
195
ms
Table 13. IO SPECIFICATIONS
TA = −40 to +855C
TA = −40 to +1055C (Note 11)
TJ = −40 to +1255C
Symbol
Parameter
VDD (V)
Conditions
Min
Typ
Max
Unit
−
−
0.4
V
50
−
−
ms
HOST INTERFACE PINS (INT_N)
VOLINTN
TINT_Mask
Output Low Voltage
3.0 to 5.5
Time from global interrupt
mask bit cleared to when
INT_N goes LOW
3.0 to 5.5
IOL = 4 mA
I2C INTERFACE PINS – STANDARD, FAST, OR FAST MODE PLUS SPEED MODE (SDA, SCL) (Note 6)
VILI2C
Low-Level Input Voltage
3.0 to 5.5
−
−
0.51
V
VIHI2C
High-Level Input Voltage
3.0 to 5.5
1.32
−
−
V
www.onsemi.com
16
FUSB302B
Table 13. IO SPECIFICATIONS
TA = −40 to +855C
TA = −40 to +1055C (Note 11)
TJ = −40 to +1255C
Symbol
Parameter
VDD (V)
Conditions
Min
Typ
Max
Unit
94
−
−
mV
I2C INTERFACE PINS – STANDARD, FAST, OR FAST MODE PLUS SPEED MODE (SDA, SCL) (Note 6)
VHYS
Hysteresis of Schmitt
Trigger Inputs
3.0 to 5.5
Input Current of SDA and
SCL Pins
3.0 to 5.5
Input Voltage 0.26 V to 2.0 V
−10
−
10
mA
ICCTI2C
VDD Current when SDA or
SCL is HIGH
3.0 to 5.5
Input Voltage 1.8 V
−10
−
10
mA
VOLSDA
Low-Level Output Voltage
(Open-Drain)
3.0 to 5.5
IOL = 2 mA
0
−
0.35
V
IOLSDA
Low-Level Output Current
(Open-Drain)
3.0 to 5.5
VOLSDA = 0.4 V
20
−
−
mA
CI
Capacitance for Each I/O
Pin (Note 7)
3.0 to 5.5
−
5
−
pF
II2C
6. I2C pull up voltage is required to be between 1.71 V and VDD.
Table 14. I2C SPECIFICATIONS FAST MODE PLUS I2C SPECIFICATIONS
Fast Mode Plus
Symbol
fSCL
tHD;STA
Parameter
I2C_SCL Clock Frequency
Hold Time (Repeated) START Condition
Min
Max
Unit
0
1000
kHz
0.26
−
ms
tLOW
Low Period of I2C_SCL Clock
0.5
−
ms
tHIGH
High Period of I2C_SCL Clock
0.26
−
ms
tSU;STA
Set-up Time for Repeated START Condition
0.26
−
ms
tHD;DAT
Data Hold Time
0
−
ms
tSU;DAT
Data Set-up Time
50
−
ns
tr
Rise Time of I2C_SDA and I2C_SCL Signals (Note 7)
−
120
ns
tf
Fall Time of I2C_SDA and I2C_SCL Signals (Note 7)
6
120
ns
Set−up Time for STOP Condition
0.26
−
ms
tBUF
Bus-Free Time between STOP and START Conditions (Note 7)
0.5
−
ms
tSP
Pulse Width of Spikes that Must Be Suppressed by the Input Filter
0
50
ns
Cb
Capacitive Load for each Bus Line (Note 7)
−
550
pF
tVD−DAT
Data Valid Time for Data from SCL LOW to SDA HIGH or LOW Output (Note 7)
0
0.45
ms
tVD−ACK
Data Valid Time for acknowledge from SCL LOW to SDA HIGH or LOW Output
(Note 7)
0
0.45
ms
tSU;STO
VnL
Noise Margin at the LOW Level (Note 7)
0.2
−
V
VnH
Noise Margin at the HIGH Level (Note 7)
0.4
−
V
7. Guaranteed by Characterization and/or Design. Not production tested.
www.onsemi.com
17
FUSB302B
Figure 17. Definition of Timing for Full-Speed Mode Devices on the I2C Bus
Table 15. I2C SLAVE ADDRESS
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
FUSB302BUCX,
FUSB302BMPX,
FUSB302BVMPX
Name
0
1
0
0
0
1
0
R/W
FUSB302B01MPX
0
1
0
0
0
1
1
R/W
FUSB302B10MPX
0
1
0
0
1
0
0
R/W
FUSB302B11MPX
0
1
0
0
1
0
1
R/W
Table 16. REGISTER DEFINITIONS (Notes 8 and 9)
Address
Register
Name
Type
Reg
Value
0x01
Device ID
R
9X
0x02
Switches0
R/W
3
PU_EN2
PU_EN1
VCONN_
CC2
VCONN_
CC1
0x03
Switches1
R/W
20
POWER
ROLE
SPEC
REV1
SPEC
REV0
DATA
ROLE
0x04
Measure
R/W
31
MEAS_
VBUS
MDAC5
MDAC4
0x05
Slice
R/W
60
SDAC_
HYS2
SDAC5
SDAC4
0x06
Control0
R/W/C
24
TX_
FLUSH
INT_MASK
0x07
Control1
R/W/C
0
ENSOP
2DB
ENSOP
1DB
0x08
Control2
R/W
2
TOG_
SAVE_
PWR1
TOG_RD_
ONLY
0x09
Control3
R/W
6
SEND_
HARD_
BIST_
TMODE
Bit 7
Bit 6
Bit 5
Bit 4
Version ID[3:0]
SDAC_
HYS1
TOG_
SAVE_
PWR2
Bit 3
MEAS_
CC2
Bit 1
AUTO_
HARD
RESET
PDWN2
PDWN1
AUTO_
CRC
TXCC2
TXCC1
MDAC3
MDAC2
MDAC1
MDAC0
SDAC3
SDAC2
SDAC1
SDAC0
HOST_
CUR1
HOST_
CUR0
AUTO_
PRE
TX_START
RX_
FLUSH
ENSOP2
ENSOP1
WAKE_EN
MODE[1:0]
TOGGLE
AUTO_
N_RETRIES[1:0]
AUTO_
RETRY
SOFTRES
ET
www.onsemi.com
Bit 0
Revision ID[1:0]
MEAS_
CC1
BIST_
MODE2
RESET
18
Bit 2
Product ID[1:0]
FUSB302B
Table 16. REGISTER DEFINITIONS (Notes 8 and 9)
Address
Register
Name
Type
Reg
Value
0x0A
Mask1
R/W
0
0x0B
Power
R/W
1
0x0C
Reset
W/C
0
0x0D
OCPreg
R/W
0F
0x0E
Maska
R/W
0
0x0F
Maskb
R/W
0
M_
GCRCSEN
T
0x10
Control4
R/W
0
TOG_
EXIT_AUD
0x3C
Status0a
R
0
SOFTFAIL
RETRY
FAIL
POWER3
POWER2
SOFTRST
HARDRST
0x3D
Status1a
R
0
TOGSS3
TOGSS2
TOGSS1
RXSOP
2DB
RXSOP
1DB
RXSOP
0x3E
Interrupta
R/C
0
I_
SOFTFAIL
I_RETRY
FAIL
I_HARD
SENT
I_TXSENT
I_SOFT
RST
I_HARD
RST
0x3F
Interruptb
R/C
0
0x40
Status0
R
0
VBUSOK
ACTIVITY
COMP
CRC_CHK
ALERT
WAKE
BC_LVL1
BC_LVL0
0x41
Status1
R
28
RXSOP2
RXSOP1
RX_
EMPTY
RX_FULL
TX_
EMPTY
TX_FULL
OVRTEMP
OCP
0x42
Interrupt
R/C
0
I_VBUSOK
I_
ACTIVITY
I_COMP_
CHNG
I_CRC_
CHK
I_ALERT
I_WAKE
I_
COLLISION
I_BC_LVL
0x43
FIFOs
R/W
(Note
10)
0
Type C Bits
USB PD Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
M_
VBUSOK
M_
ACTIVITY
M_COMP_
CHNG
M_CRC_C
HK
M_ALERT
M_WAKE
M_
COLLISION
M_BC_LVL
PWR3
PWR2
PWR1
PWR0
PD_
RESET
SW_RES
M_OCP_
TEMP
I_OCP_
TEMP
M_
TOGDONE
I_
TOGDONE
M_SOFT
FAIL
M_RETRY
FAIL
OCP_
RANGE
OCP_
CUR2
OCP_
CUR1
OCP_
CUR0
M_HARD
SENT
M_
TXSENT
M_
SOFTRST
M_
HARDRST
I_GCRCS
ENT
Write to TX FIFO or read from RX FIFO repeatedly without address auto increment
General Bits
8. Do not use registers that are blank.
9. Values read from undefined register bits are not defined and invalid. Do not write to undefined registers.
10. FIFO register is serially read/written without auto address increment.
11. Automotive Part Only; FUSB302BVMPX
Table 17. DEVICE ID
(Address: 01h; Reset Value: 0x1001_XXXX; Type: Read)
Bit #
Name
R/W/C
Size (Bits)
7:4
Version ID
R
4
Device version ID by Trim or etc.
A_[Revision ID]: 1000 (e.g. A_revA)
B_[Revision ID]: 1001
C_[Revision ID]: 1010 etc
Description
3:2
Product ID
R
2
“01”, “10” and “11” applies to MLP only:
00: FUSB302BMPX/FUSB302BVMPX(Default) & FUSB302BUCX
01: FUSB302B01MPX
10: FUSB302B10MPX
11: FUSB302B11MPX
1:0
Revision ID
R
2
Revision History of each version
[Version ID]_revA: 00(e.g. revA)
[Version ID]_revB: 01 (e.g. revB)
[Version ID]_revC: 10 (e.g. revC)
[Version ID]_revC: 11 (e.g. revD)
www.onsemi.com
19
FUSB302B
Table 18. SWITCHES0
(Address: 02h; Reset Value: 0x0000_0011; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7
PU_EN2
R/W
1
1:
Apply host pull up current to CC2 pin
6
PU_EN1
R/W
1
1:
Apply host pull up current to CC1 pin
5
VCONN_CC2
R/W
1
1:
Turn on the VCONN current to CC2 pin
4
VCONN_CC1
R/W
1
1:
Turn on the VCONN current to CC1 pin
3
MEAS_CC2
R/W
1
1:
Use the measure block to monitor or measure the voltage on
CC2
2
MEAS_CC1
R/W
1
1:
Use the measure block to monitor or measure the voltage on
CC1
1
PDWN2
R/W
1
1:
Device pull down on CC2. 0: no pull down
0
PDWN1
R/W
1
1:
Device pull down on CC1. 0: no pull down
Table 19. SWITCHES1
(Address: 03h; Reset Value: 0x0010_0000; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7
POWERROLE
R/W
1
Bit used for constructing the GoodCRC acknowledge packet. This
bit corresponds to the Port Power Role bit in the message header if
an SOP packet is received:
1: Source if SOP
0: Sink if SOP
6:5
SPECREV1:
SPECREV0
R/W
2
Bit used for constructing the GoodCRC acknowledge packet.
These bits correspond to the Specification Revision bits in the
message header:
00: Revision 1.0
01: Revision 2.0
10: Do Not Use
11: Do Not Use
4
DATAROLE
R/W
1
Bit used for constructing the GoodCRC acknowledge packet. This
bit corresponds to the Port Data Role bit in the message header.
For SOP:
1: SRC
0: SNK
3
Reserved
N/A
1
Do Not Use
2
AUTO_CRC
R/W
1
1:
0:
Starts the transmitter automatically when a message with a
good CRC is received and automatically sends a GoodCRC
acknowledge packet back to the relevant SOP*
Feature disabled
1
TXCC2
R/W
1
1:
Enable BMC transmit driver on CC2 pin
0
TXCC1
R/W
1
1:
Enable BMC transmit driver on CC1 pin
www.onsemi.com
20
FUSB302B
Table 20. MEASURE
(Address: 04h; ·Reset Value: 0x0011_0001; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7
Reserved
N/A
1
Do Not Use
6
MEAS_VBUS
R/W
1
0:
1:
5:0
MDAC[5:0]
R/W
6
MDAC/comparator measurement is controlled by MEAS_CC*
bits
Measure VBUS with the MDAC/comparator. This requires
MEAS_CC* bits to be 0
Measure Block DAC data input. LSB is equivalent to 42 mV of
voltage which is compared to the measured CC voltage.
The measured CC is selected by MEAS_CC2, or MEAS_CC1 bits.
MDAC[5:0]
MEAS_VBUS = 0 MEAS_VBUS = 1 Unit
00_0000
0.042
0.420
V
00_0001
0.084
0.840
V
11_0000
2.058
20.58
V
11_0011
2.184
21.84
V
11_1110
2.646
26.46
V
11_1111
> 2.688
26.88
V
Table 21. SLICE
(Address: 05h; Reset Value: 0x0110_0000; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7:6
SDAC_HYS[1:0]
R/W
2
Adds hysteresis where there are now two thresholds, the lower
threshold which is always the value programmed by SDAC[5:0]
and the higher threshold that is:
11: 255 mV hysteresis: higher threshold = (SDAC value + 20hex)
10: 170 mV hysteresis: higher threshold = (SDAC value + Ahex)
01: 85 mV hysteresis: higher threshold = (SDAC value + 5)
00: No hysteresis: higher threshold = SDAC value
5:0
SDAC[5:0]
R/W
6
BMC Slicer DAC data input. Allows for a programmable threshold
so as to meet the BMC receive mask under all noise conditions.
Table 22. CONTROL0
(Address: 06h; Reset Value: 0x0010_0100; Type: (see column below))
Bit #
Name
R/W/C
Size (Bits)
7
Reserved
N/A
1
Do Not Use
6
TX_FLUSH
W/C
1
1:
Self clearing bit to flush the content of the transmit FIFO
5
INT_MASK
R/W
1
1:
0:
Mask all interrupts
Interrupts to host are enabled
4
Reserved
N/A
1
Do Not Use
3:2
HOST_CUR[1:0]
R/W
2
1:
00:
01:
10:
11:
Controls the host pull up current enabled by PU_EN[2:1]:
No current
80 mA – Default USB power
180 mA – Medium Current Mode: 1.5 A
330 mA – High Current Mode: 3 A
1
AUTO_PRE
R/W
1
1:
Starts the transmitter automatically when a message with
a good CRC is received. This allows the software to take as
much as 300 mS to respond after the I_CRC_CHK interrupt is
received. Before starting the transmitter, an internal timer
waits for approximately 170 mS before executing the transmit
start and preamble
Feature disabled
Description
0:
0
TX_START
W/C
1
1:
Start transmitter using the data in the transmit FIFO. Preamble
is started first. During the preamble period the transmit data
can start to be written to the transmit FIFO. Self clearing.
www.onsemi.com
21
FUSB302B
Table 23. CONTROL1
(Address: 07h; Reset Value: 0x0000_0000; Type: (see column below))
Bit #
Name
R/W/C
Size (Bits)
Description
7
Reserved
N/A
1
Do Not Use
6
ENSOP2DB
R/W
1
1:
0:
Enable SOP”_DEBUG (SOP double prime debug) packets
Ignore SOP”_DEBUG (SOP double prime debug) packets
5
ENSOP1DB
R/W
1
1:
0:
Enable SOP _DEBUG (SOP prime debug) packets
Ignore SOP _DEBUG (SOP prime debug) packets
4
BIST_MODE2
R/W
1
1:
Sent BIST Mode 01s pattern for testing
3
Reserved
N/A
1
Do Not Use
2
RX_FLUSH
W/C
1
1:
Self clearing bit to flush the content of the receive FIFO
1
ENSOP2
R/W
1
1:
0:
Enable SOP”(SOP double prime) packets
Ignore SOP”(SOP double prime) packets
0
ENSOP1
R/W
1
1:
0:
Enable SOP (SOP prime) packets
Ignore SOP (SOP prime) packets
Table 24. CONTROL2
(Address: 08h; Reset Value: 0x0000_0010; Type: (see column below))
Bit #
Name
R/W/C
Size (Bits)
Description
7:6
TOG_SAVE_PWR2:
TOG_SAVE_PWR1
N/A
2
00:
01:
10:
11:
Don’t go into the DISABLE state after one cycle of toggle
Wait between toggle cycles for tDIS time of 40 ms
Wait between toggle cycles for tDIS time of 80 ms
Wait between toggle cycles for tDIS time of 160 ms
5
TOG_RD_ONLY
R/W
1
1:
When TOGGLE=1 only Rd values will cause the TOGGLE
state machine to stop toggling and trigger the I_TOGGLE
interrupt
When TOGGLE=1, Rd and Ra values will cause the TOGGLE
state machine to stop toggling
0:
4
Reserved
N/A
1
Do Not Use
3
WAKE_EN
R/W
1
1:
0:
Enable Wake Detection functionality if the power state is
correct
Disable Wake Detection functionality
2:1
MODE
R/W
2
11:
10:
01:
00:
Enable SRC polling functionality if TOGGLE=1
Enable SNK polling functionality if TOGGLE=1
Enable DRP polling functionality if TOGGLE=1
Do Not Use
0
TOGGLE
R/W
1
1:
0:
Enable DRP, SNK or SRC Toggle autonomous functionality
Disable DRP, SNK and SRC Toggle functionality
www.onsemi.com
22
FUSB302B
Table 25. CONTORL3
(Address: 09h; Reset Value: 0x0000_0110; Type: (see column below))
Bit #
Name
R/W/C
Size (Bits)
Description
7
Reserved
N/A
1
Do Not Use
6
SEND_HARD_RESET
W/C
1
1:
0:
Send a hard reset packet (highest priority)
Don’t send a soft reset packet
5
BIST_TMODE
R/W
1
1:
0:
BIST mode. Receive FIFO is cleared immediately after
sending GoodCRC response
Normal operation, All packets are treated as usual
4
AUTO_HARDRESET
R/W
1
1:
0:
Enable automatic hard reset packet if soft reset fail
Disable automatic hard reset packet if soft reset fail
3
AUTO_SOFTRESET
R/W
1
1:
0:
Enable automatic soft reset packet if retries fail
Disable automatic soft reset packet if retries fail
2:1
N_RETRIES[1:0]
R/W
2
11:
10:
01:
00:
Three retries of packet (four total packets sent)
Two retries of packet (three total packets sent)
One retry of packet (two total packets sent)
No retries (similar to disabling auto retry)
0
AUTO_RETRY
R/W
1
1:
0:
Enable automatic packet retries if GoodCRC is not received
Disable automatic packet retries if GoodCRC not received
Table 26. MASK
(Address: 0Ah; Reset Value: 0x0000_0000; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7
M_VBUSOK
R/W
1
1:
0:
Mask I_VBUSOK interrupt bit
Do not mask
6
M_ACTIVITY
R/W
1
1:
0:
Mask interrupt for a transition in CC bus activity
Do not mask
5
M_COMP_CHNG
R/W
1
1:
0:
Mask I_COMP_CHNG interrupt for change is the value of
COMP, the measure comparator
Do not mask
4
M_CRC_CHK
R/W
1
1:
0:
Mask interrupt from CRC_CHK bit
Do not mask
3
M_ALERT
R/W
1
1:
0:
Mask the I_ALERT interrupt bit
Do not mask
2
M_WAKE
R/W
1
1:
0:
Mask the I_WAKE interrupt bit
Do not mask
1
M_COLLISION
R/W
1
1:
0:
Mask the I_COLLISION interrupt bit
Do not mask
0
M_BC_LVL
R/W
1
1:
0:
Mask a change in host requested current level
Do not mask
Table 27. POWER
(Address: 0Bh; Reset Value: 0x0000_0001; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7:4
Reserved
N/A
4
Do Not Use
3:0
PWR[3:0]
R/W
4
Power enables:
PWR[0]: Bandgap and wake circuit
PWR[1]: Receiver powered and current references for Measure
block
PWR[2]: Measure block powered
PWR[3]: Enable internal oscillator
www.onsemi.com
23
FUSB302B
Table 28. RESET
(Address: 0Ch; Reset Value: 0x0000_0000; Type: Write/Clear)
Bit #
Name
R/W/C
Size (Bits)
Description
7:2
Reserved
N/A
6
Do Not Use
1
PD_RESET
W/C
1
1:
Reset just the PD logic for both the PD transmitter and
receiver
0
SW_RES
W/C
1
1:
Reset the FUSB302B including the I2C registers to their
default values
Table 29. OCPREG
(Address: 0Dh; Reset Value: 0x0000_1111; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7:4
Reserved
N/A
4
Do Not Use
3
OCP_RANGE
R/W
1
1:
0:
2:0
OCP_CUR2,
OCP_CUR1,
OCP_CUR0
R/W
3
111: max_range (see bit definition above for OCP_RANGE)
110: 7 × max_range / 8
101: 6 × max_range / 8
100: 5 × max_range / 8
011: 4 × max_range / 8
010: 3 × max_range / 8
001: 2 × max_range / 8
000: max_range / 8
OCP range between 100−800 mA (max_range = 800 mA)
OCP range between 10−80 mA (max_range = 80 mA)
Table 30. MASKA
(Address: 0Eh; Reset Value: 0x0000_0000; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7
M_OCP_TEMP
R/W
1
1:
Mask the I_OCP_TEMP interrupt
6
M_TOGDONE
R/W
1
1:
Mask the I_TOGDONE interrupt
5
M_SOFTFAIL
R/W
1
1:
Mask the I_SOFTFAIL interrupt
4
M_RETRYFAIL
R/W
1
1:
Mask the I_RETRYFAIL interrupt
3
M_HARDSENT
R/W
1
1:
Mask the I_HARDSENT interrupt
2
M_TXSENT
R/W
1
1:
Mask the I_TXSENT interrupt
1
M_SOFTRST
R/W
1
1:
Mask the I_SOFTRST interrupt
0
M_HARDRST
R/W
1
1:
Mask the I_HARDRST interrupt
Table 31. MASKB
(Address: 0Fh; Reset Value: 0x0000_0000; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
7:1
Reserved
N/A
6
Do Not Use
Description
0
M_GCRCSENT
R/W
1
1:
Mask the I_GCRCSENT interrupt
Table 32. CONTROL4
(Address: 00h; Reset Value: 0x0000_0000; Type: Read/Write)
Bit #
Name
R/W/C
Size (Bits)
Description
7:1
Reserved
N/A
6
Do Not Use
0
TOG_EXIT_AUD
R/W
1
1:
In auto Rd only Toggle mode, stop Toggle at Audio accessory
(Ra on both CC)
www.onsemi.com
24
FUSB302B
Table 33. STATUS0A
(Address: 3Ch; Reset Value: 0x0000_0000; Type: Read)
Bit #
Name
R/W/C
Size (Bits)
Description
7:6
Reserved
N/A
2
Do Not Use
5
SOFTFAIL
R
1
1:
All soft reset packets with retries have failed to get
a GoodCRC acknowledge. This status is cleared when
a START_TX, TXON or SEND_HARD_RESET is executed
4
RETRYFAIL
R
1
1:
All packet retries have failed to get a GoodCRC acknowledge.
This status is cleared when a START_TX, TXON or
SEND_HARD_RESET is executed
3:2
POWER3:POWER2
R
2
Internal power state when logic internals needs to control the
power state. POWER3 corresponds to PWR3 bit and POWER2
corresponds to PWR2 bit. The power state is the higher of both
PWR[3:0] and {POWER3, POWER2, PWR[1:0]} so that if one is
03 and the other is F then the internal power state is F
1
SOFTRST
R
1
1:
One of the packets received was a soft reset packet
0
HARDRST
R
1
1:
Hard Reset PD ordered set has been received
Table 34. STATUS1A
(Address: 3Dh; Reset Value: 0x0000_0000; Type: Read)
Bit #
Name
R/W/C
Size (Bits)
Description
7:6
Reserved
N/A
2
Do Not Use
5:3
TOGSS3,
TOGSS2,
TOGSS1
R
3
000: Toggle logic running (processor has previously written
TOGGLE=1)
001: Toggle functionality has settled to SRCon CC1
(STOP_SRC1 state)
010: Toggle functionality has settled to SRCon CC2
(STOP_SRC2 state)
101: Toggle functionality has settled to SNKon CC1
(STOP_SNK1 state)
110: Toggle functionality has settled to SNKon CC2
(STOP_SNK2 state)
111: Toggle functionality has detected AudioAccessory with vRa
on both CC1 and CC2 (settles to STOP_SRC1 state)
Otherwise: Not defined (do not interpret)
2
RXSOP2DB
R
1
1: Indicates the last packet placed in the RxFIFO is type
SOP”_DEBUG (SOP double prime debug)
1
RXSOP1DB
R
1
1: Indicates the last packet placed in the RxFIFO is type
SOP’_DEBUG (SOP prime debug)
0
RXSOP
R
1
1: Indicates the last packet placed in the RxFIFO is type SOP
www.onsemi.com
25
FUSB302B
Table 35. INTERRUPTA
(Address: 3Eh; Reset Value: 0x0000_0000; Type: Read/Clear)
Bit #
Name
R/W/C
Size (Bits)
Description
7
I_OCP_TEMP
R/C
1
1:
Interrupt from either a OCP event on one of the VCONN
switches or an over-temperature event
6
I_TOGDONE
R/C
1
1:
Interrupt indicating the TOGGLE functionality was terminated
because a device was detected
5
I_SOFTFAIL
R/C
1
1:
Interrupt from automatic soft reset packets with retries have
failed
4
I_RETRYFAIL
R/C
1
1:
Interrupt from automatic packet retries have failed
3
I_HARDSENT
R/C
1
1:
Interrupt from successfully sending a hard reset ordered set
2
I_TXSENT
R/C
1
1:
Interrupt to alert that we sent a packet that was acknowledged
with a GoodCRC response packet
1
I_SOFTRST
R/C
1
1:
Received a soft reset packet
0
I_HARDRST
R/C
1
1:
Received a hard reset ordered set
Table 36. INTERRUPTB
(Address: 3Fh; Reset Value: 0x0000_0000; Type: Read/Clear)
Bit #
Name
R/W/C
Size (Bits)
Description
7
Reserved
N/A
6
Do Not Use
0
I_GCRCSENT
R/C
1
1:
Sent a GoodCRC acknowledge packet in response to
an incoming packet that has the correct CRC value
www.onsemi.com
26
FUSB302B
Table 37. STATUS0
(Address: 40h; Reset Value: 0x0000_0000; Type: Read)
Bit #
Name
R/W/C
Size (Bits)
Description
7
VBUSOK
R
1
1:
Interrupt occurs when VBUS transitions through vVBUSthr.
This bit typically is used to recognize port partner during
startup
6
ACTIVITY
R
1
1:
Transitions are detected on the active CC* line. This bit goes
high after a minimum of 3 CC transitions, and goes low with
no Transitions
Inactive
0:
5
COMP
R
1
1:
0:
4
CRC_CHK
R
1
1:
0:
Measured CC* input is higher than reference level driven from
the MDAC
Measured CC* input is lower than reference level driven
from the MDAC
Indicates the last received packet had the correct CRC. This
bit remains set until the SOP of the next packet
Packet received for an enabled SOP* and CRC for the
enabled packet received was incorrect
3
ALERT
R
1
1:
Alert software an error condition has occurred. An alert is
caused by:
TX_FULL: the transmit FIFO is full
RX_FULL: the receive FIFO is full
See Status1 bits
2
WAKE
R
1
1:
0:
Voltage on CC indicated a device attempting to attach
WAKE either not enabled (WAKE_EN=0) or no device
attached
1:0
BC_LVL[1:0]
R
2
Current voltage status of the measured CC pin interpreted as host
current levels as follows:
00: < 200 mV
01: > 200 mV, < 660 mV
10: > 660 mV, < 1.23 V
11: > 1.23 V
Note the software must measure these at an appropriate time,
while there is no signaling activity on the selected CC line.
BC_LVL is only defined when Measure block is on which is when
register bits PWR[2]=1 and either MEAS_CC1=1 or MEAS_CC2=1
Description
Table 38. STATUS1
(Address: 41h; Reset Value: 0x0010_1000; Type: Read)
Bit #
Name
R/W/C
Size (Bits)
7
RXSOP2
R
1
1:
Indicates the last packet placed in the RxFIFO is type SOP”
(SOP double prime)
6
RXSOP1
R
1
1:
Indicates the last packet placed in the RxFIFO is type SOP’
(SOP prime)
5
RX_EMPTY
R
1
1:
The receive FIFO is empty
4
RX_FULL
R
1
1:
The receive FIFO is full
3
TX_EMPTY
R
1
1:
The transmit FIFO is empty
2
TX_FULL
R
1
1:
The transmit FIFO is full
1
OVRTEMP
R
1
1:
Temperature of the device is too high
0
OCP
R
1
1:
Indicates an over-current or short condition has occurred on
the VCONN switch
www.onsemi.com
27
FUSB302B
Table 39. INTERRUPT
(Address: 42h; Reset Value: 0x0000_0000; Type: Read/Clear)
Bit #
Name
R/W/C
Size (Bits)
Description
7
I_VBUSOK
R/C
1
1:
Interrupt occurs when VBUS transitions through 4.5 V. This bit
typically is used to recognize port partner during startup
6
I_ACTIVITY
R/C
1
1:
A change in the value of ACTIVITY of the CC bus has occurred
5
I_COMP_CHNG
R/C
1
1:
A change in the value of COMP has occurred. Indicates selected CC line has tripped a threshold programmed into the
MDAC
4
I_CRC_CHK
R/C
1
1:
The value of CRC_CHK newly valid. I.e. The validity of the
incoming packet has been checked
3
I_ALERT
R/C
1
1:
Alert software an error condition has occurred. An alert is
caused by:
TX_FULL: the transmit FIFO is full
RX_FULL: the receive FIFO is full
See Status1 bits
2
I_WAKE
R/C
1
1:
Voltage on CC indicated a device attempting to attach.
Software must then power up the clock and receiver blocks
1
I_COLLISION
R/C
1
1:
When a transmit was attempted, activity was detected on the
active CC line. Transmit is not done. The packet is received
normally
0
I_BC_LVL
R/C
1
1:
A change in host requested current level has occurred
Table 40. FIFOS
(Address: 43h; Reset Value: 0x0000_0000; Type: (see column below))
Bit #
Name
R/W/C
Size (Bits)
Description
7:0
TX/RX Token
Read or
Write
8
Writing to this register writes a byte into the transmit FIFO.
Reading from this register reads from the receive FIFO.
Each byte is a coded token. Or a token followed by a fixed number
of packed data byte (see token coding in Table 41)
Software Model
Transmit Data Tokens
Port software interacts with the port chip in two primary
ways:
• I2C Registers
• 8 bit data tokens sent to or received from the FIFO
register
• All reserved bits written in the TxFIFO should be 0 and
all reserved bit read from the RxFIFO should be
ignored
Transmit data tokens provide in-sequence transmit
control and data for the transmit logic. Note that the token
codes, and their equivalent USB PD K-Code are not the
same. Tokens are read one at a time when they reach the end
of the TX FIFO. I.e., the specified token action is performed
before the next token is read from the TX FIFO.
The tokens are defined as follows:
www.onsemi.com
28
FUSB302B
Table 41. TOKENS USED IN FIFO
Code
Name
Size (Bytes)
Description
101x−xxx1
(0xA1)
TXON
1
Alternative method for starting the transmitter with the TX−START bit. This is not
a token written to the TxFIFO but a command much like TX_START but it is
more convenient to write it while writing to the TxFIFO in one contiguous write
operation. It is preferred that the TxFIFO is first written with data and then TXON
or TX_START is executed. It is expected that A1h will be written for TXON not
any other bits where x is non-zero such as B1h, BFh, etc
0x12
SOP1
1
When reaching the end of the FIFO causes a Sync−1 symbol to be transmitted
0x13
SOP2
1
When reaching the end of the FIFO causes a Sync−2 symbol to be transmitted
0x1B
SOP3
1
When reaching the end of the FIFO causes a Sync−3 symbol to be transmitted
0x15
RESET1
1
When reaching the end of the FIFO causes a RST−1 symbol to be transmitted
0x16
RESET2
1
When reaching the end of the FIFO causes a RST−2 symbol to be transmitted
0x80
PACKSYM
1+N
0xFF
JAM_CRC
1
Causes the CRC, calculated by the hardware, to be inserted into the transmit
stream when this token reaches the end of the TX FIFO
0x14
EOP
1
Causes an EOP symbol to be sent when this token reaches the end of the TX
FIFO
0xFE
TXOFF
1
Turn off the transmit driver. Typically the next symbol after EOP
This data token must be immediately followed by a sequence of N packed data
bytes. This token is defined by the 3 MSB’s being set to 3’b100. The 5 LSB’s are
the number of packed bytes being sent.
Note: N cannot be less than 2 since the minimum control packet has a header
that is 2 bytes and N cannot be greater than 30 since the maximum data packet
has 30 bytes (2 byte header + 7 data objects each having 4 bytes)
Packed data bytes have two 4 bit data fields. The 4 LSB’s are sent first, after
4b5b conversion etc in the chip
RECEIVE DATA TOKENS
Receive data tokens provide in-sequence receive control
and data for the receive logic. The RxFIFO can absorb as
many packets as the number of bytes in the RxFIFO
(80 bytes). The tokens are defined as follows:
Table 42. TOKENS USED IN RxFIFO
Code
Name
Size (Bytes)
Description
111b_bbbb
SOP
1
First byte of a received packet to indicate that the packet is an SOP packet
(“b” is undefined and can be any bit)
110b_bbbb
SOP1
1
First byte of a received packet to indicate that the packet is an SOP’ packet
and occurs only if ENSOP1=1 (“b” is undefined and can be any bit)
101b_bbbb
SOP2
1
First byte of a received packet to indicate that the packet is an SOP” packet
and occurs only if ENSOP2=1 (“b” is undefined and can be any bit)
100b_bbbb
SOP1DB
1
First byte of a received packet to indicate that the packet is an SOP’_DEBUG
packet and occurs only if ENSOP1DB=1 (“b” is undefined and can be any bit)
011b_bbbb
SOP2DB
1
First byte of a received packet to indicate that the packet is an SOP”_DEBUG
packet and occurs only if ENSOP2DB=1 (“b” is undefined and can be any bit)
010b_bbbb/
001b_bbbb/
000b_bbbb
Do Not Use
1
These can be used in future versions of this device and should not be relied
on to be any special value. (“b” is undefined and can be any bit)
www.onsemi.com
29
FUSB302B
REFERENCE SCHEMATIC
VBUS_IN
J2
FUSB302B
VCONN
VDD
CBULK
CVCONN
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A2
V
B1 BUS
V
A3 CONN
VOD
CVDD2
CVDD1
B3
SCL
C3
SDA
B2
INT_N
SCL
SDA
INT_N
CC1
CC2
CC1
C1
A1
CRECV
GND
CRECV
C2
RPU
RPU
RPU_INT
VPU
USB TYP-C
B1
GNDB1
GNDA2
B2
RX2P
TX2P
B3
RX2M
TX2M
B4
VBUSA2
VBUSB1
B5
RFU1
CC2
B6
DMA
DPB
B7
DPA
DMB
B8
CC1
RFU2
B9
VBUSA1
VBUSB2
B10
TX1M
RX1M
B11
TX1P
RX1P
B12
GNDA1
GNDB2
CC2
Figure 18. FUSB302/FUSB302B Reference Schematic Diagram
Table 43. RECOMMENDED COMPONENT VALUES FOR REFERENCE SCHEMATIC
Recommended Value
Symbol
Parameter
Min
Typ
Max
Unit
CRECV
CCX Receiver Capacitance
200
−
600
pF
CBULK
VCONN Source Bulk Capacitance
10
−
220
mF
CVCONN
VCONN Decoupling Capacitance
−
0.1
−
mF
CVDD1
VDD Decoupling Capacitance
−
0.1
−
mF
CVDD2
VDD Decoupling Capacitance
−
1.0
−
mF
I2C Pull-up Resistors
−
4.7
−
kW
INT_N Pull-up Resistor
1.0
4.7
−
kW
I2C
1.71
−
VDD
V
RPU
RPU_INT
VPU
Pull-up Voltage
The table below is in reference to the WLCSP package
drawing on the following page.
Table 44. PRODUCT-SPECIFIC DIMENSIONS
Product
D
E
X
Y
FUSB302BUCX
1.260 mm
1.215 mm
0.2075 mm
0.230 mm
I2C Bus is a trademark of Philips Corporation. All other brand names and product names appearing in this document are registered
trademarks or trademarks of their respective holders.
www.onsemi.com
30
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
WQFN14 2.5x2.5, 0.5P
CASE 510BR
ISSUE O
DATE 31 AUG 2016
SCALE 4:1
0.05 C
2.50
2X
A
B
2.43
1.45
PIN #1 IDENT
2.50
2.43
1.45
0.05 C
TOP VIEW
2X
(0.58)
0.75±0.05
0.50 TYP
0.10 C
0.15±0.05
0.08 C
0.30 TYP
RECOMMENDED LAND PATTERN
C
0.025±0.025
SEATING
PLANE
FRONT VIEW
NOTES:
A. NO JEDEC REGISTRATION.
2.50±0.05
1.45±0.05
B. DIMENSIONS ARE IN MILLIMETERS.
7
4
C. DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 2009.
8
3
D. LAND PATTERN RECOMMENDATION IS
EXISTING INDUSTRY LAND PATTERN.
0.50
1.45±0.05
10
1
0.30(14X)
PIN #1 IDENT
14
11
0.50
BOTTOM VIEW
DOCUMENT NUMBER:
DESCRIPTION:
0.24±0.06 (14X)
0.10
C A B
0.05
C
98AON13629G
WQFN14 2.5X2.5, 0.5P
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
WLCSP9 1.26x1.215x0.526
CASE 567TN
ISSUE O
SCALE 5:1
DOCUMENT NUMBER:
DESCRIPTION:
98AON13359G
WLCSP9 1.26x1.215x0.526
DATE 31 MAR 2017
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
www.onsemi.com
1
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative