IML-0688

For Reference Only: Fresnel Lens IML-0688 1/7 Product Specification 1. Scope This product specification is applied to fresnel lens IML-0688 used for Pyroelectric infared sensor IRA-S210ST01 to detect infrared ray. Please contact us when using this product for any other applications than described in the above. 2. Murata Part Number IML-0688 3. Outline Drawing and Dimensions See Figure 1 4. Material etc. 4-1 Material High density polyethylene 4-2 Refractive Index 1.51 4-3 Transmittance See Figure 4 4-4 Color IML-0688 ： Natural White IML-0688G ： Dark Gray IML-0688W ： White 5. Lens 5-1 Field of View See Figure 2 and Figure 3 6. Operating Temperature -25 to 60°C 7. Storage Temperature -30 to 80°C For Reference Only: 2/7 8. Caution 8-1 Limitation of Applications Please contact us before using our for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. 1. Aircraft equipment 2. Aerospace equipment 3. Undersea equipment 4. Power plant control equipment 5. Medical equipment 6. Transportation equipment (vehicles, trans, ships, etc.) 7. Traffic signal equipment 8. Disaster prevention / crime prevention equipment 9. Data-processing equipment 10. Application of similar complexity and/or reliability requirement to the applications listed in the above 8-2 Fail-safe Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. For Reference Only: 3/7 9.Caution in use 9-1 Notice in design 1) Please set the direction of the tab of fresnel lens to the tab of sensor. 2) To bring pyro-Element into the focus of fresnel lens, Please push the sensor until the step inside the fresnel lens. 3) Please add any mechanism for preventing dislocation or for preventing coming off from the sensor because of transition fit between sensor and fresnel lens 4) Please avoid using the fresnel lens in the following conditions because it may cause failure or malfunction ; a) in such a fluid as water, alcohol etc. corrosive gas (S0 2,Cl2,NOX etc.) or b) c) d) e) f) sea breeze. in high humidity. in a place exposed directly to sun light or headlight of automobile. in a place exposed directly to blow from air-conditioner or heater. in such a place where infrared ray is shaded. in any other place similar to the above (a) through (e). 9-2 Notice in handling and storage 1) Optical filter of sensor should not be scratched or soiled. 2) Strong shock should be avoided. 3) High temperature, high humidity, fluid as water or alcohol etc., corrosive gas (S02,Cl2,NOX etc.) and sea breeze should be avoided. 4) Use the products within 6 months after receiving. 10. Note 1） Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2） You are requested not to use our product deviating from the agreed specifications. 3） We consider it not to appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. Therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid. For Reference Only: 4/7 ※Please set the direction of the tab on the fresnel lens to the tab on the sensor. ※To bring pyro-Element into the focus of fresnel lens, Please push the sensor until the step inside the fresnel lens. ※Please design the housing that the sensor does not receive infrared ray through the area shown as TabA TabB diagram in Figure A. ※Please design housing and set of sensor and lens to prevent from dislocation and coming off . φ8.9 φ8.1 R6 3.4 4.5 8.55 Step φ10.3 Pyro-Element 3.0 1.15 stray light degree （4.45） 13deg. Housing 10.8 Unit：mm General tolerance：±0.2 Figure Ａ An example of a design of the housing Figure 1 9.15 1.15 4.0 10.8 （4.35） 13deg. For Reference Only: 5/7 3m 6.11m 42deg. 3m 0m 42deg. 4.91m 3m Floor 0m 3m Vertical 3m Vertical TabＢ Horizontal TabＡ Pyro-Element 45.5deg. 45.5deg. Horizontal ※Assembled with Murata sensor IRA-S210 series Figure 2 For Reference Only: 6/7 3m 5.55m 42.4deg. 3m 0m 42.4deg. 5.48m 3m Floor 3m 0m Vertical 3m Vertical TabＢ Horizontal TabＡ Pyro-Element 42.8deg. 42.8deg. Horizontal ※Assembled with Murata sensor IRA-S210 series Figure 3 For Reference Only: Wave length % 2.5 3.0 4000 3500 100 7/7 4.0 5.0 6.0 2500 2000 7.0 8.0 10.0 12.0 1400 1200 1000 800 20.0  m 80 60 40 20 0 3000 1800 1600 Wave number Figure 4. Transmittance 600 -1 cm