LQH66SN121M03L

Reference Only SpecNo.JELF243A-0047W-01 P1/8 CHIP COIL（CHIP INDUCTORS）LQH66SN□□□□03L SPECIFICATION 1.Scope This reference specification applies to LQH66SN_03L Series, Chip coil (Chip Inductors). 2.Part Numbering (ex) 1 LQ H 66 Product ID Structure Dimension (L×W) 1 1 S N R27 M 0 3 L Applications Category Inductance Tolerance Features Electrode Packaging and L: Taping Characteristics 1 1 1 1 1 1 1 3.Rating ・Operating Temperature Range. ・Storage Temperature Range. Customer Part Number -40 to +80°C -40 to +85°C DC Resistance (Ω) Self Resonant Frequency (MHz min) Rated Current (A) 0.27 0.007 ± 40% 300 6.0 0.68 0.010 ± 40% 180 5.3 LQH66SN1R0M03L 1.0 0.013 ± 40% 150 4.7 LQH66SN1R5M03L 1.5 0.016 ± 40% 110 3.8 LQH66SN2R2M03L 2.2 0.019 ± 40% 80 3.3 LQH66SN3R3M03L 3.3 0.022 ± 40% 40 2.6 LQH66SN4R7M03L 4.7 0.025 ± 40% 30 2.2 LQH66SN6R8M03L 6.8 0.029 ± 40% 25 1.8 LQH66SN100M03L 10 0.036 ± 40% 20 1.6 LQH66SN150M03L 15 0.069 ± 40% 17 1.3 LQH66SN220M03L 22 0.087 ± 40% 15 1.1 Inductance MURATA Part Number (µH) LQH66SNR27M03L LQH66SNR68M03L LQH66SN330M03L 33 LQH66SN470M03L 47 LQH66SN680M03L Tolerance (%) 0.14 ± 40% 12 0.86 0.17 ± 40% 10 0.76 68 0.29 ± 40% 7.6 0.60 LQH66SN101M03L 100 0.36 ± 40% 6.5 0.52 LQH66SN151M03L 150 0.63 ± 40% 5.0 0.42 LQH66SN221M03L 220 0.79 ± 40% 4.0 0.35 LQH66SN331M03L 330 1.8 ± 40% 3.2 0.28 LQH66SN471M03L 470 2.2 ± 40% 2.5 0.24 LQH66SN681M03L 680 3.9 ± 40% 2.0 0.20 LQH66SN102M03L 1000 4.9 ± 40% 1.7 0.16 LQH66SN222M03L 2200 9.4 ± 40% 1.2 0.10 ±20 LQH66SN472M03L 4700 19.5 ± 40% 0.8 0.07 LQH66SN103M03L 10000 39.7 ± 40% 0.5 0.05  When applied Rated current to the Products, Inductance will be within ±10% of initial Inductance value. When applied Rated current to the Products ,temperature rise caused by self-generated heat shall be limited to 40°C max. 4. Testing Conditions 《Unless otherwise specified》 Temperature : Ordinary Temperature (15 to 35°C) Humidity : Ordinary Humidity (25 to 85 %(RH)) 《In case of doubt》 Temperature Humidity Atmospheric Pressure MURATA MFG.CO., LTD : 20 ± 2°C : 60 to 70 %(RH) : 86 to 106 kPa Reference Only SpecNo.JELF243A-0047W-01 P2/8 5.Appearance and Dimensions 6.3 ± 0.3 4.7 ± 0.3 6.3 ± 0.3 ■Unit Mass (Typical value) 0.71g 6.3 ± 0.3 ( in mm ) ※ No Marking. 1.3 min. 1.7 min. 1.3 min. 6.Electrical Performance No. 6.1 Item Inductance Specification Inductance shall meet item 3. Test Method 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment：Digital multi meter 6.3 Self Resonant Frequency(S.R.F) S.R.F shall meet item 3. Measuring Equipment： f  1 MHz：KEYSIGHT 4194A or equivalent f  1 MHz：KEYSIGHT E4991A or equivalent Measuring Equipment：KEYSIGHT 4194A or equivalent Measuring Frequency：1 MHz / 0.12 to 68 μH 100 kHz / 100 to 680 μH 10 kHz / 1000 to 10000 μH 7.Mechanical Performance No. 7.1 Item Shear Test Specification Chip coil shall not be damaged. Test Method Substrate：Glass-epoxy substrate Applied Direction： Chip Coil F Substrate Force：10N Hold Duration：5±1 s 7.2 Bending Test Substrate：Glass-epoxy substrate (100  40  1.6mm) Speed of Applying Force：1mm / s Deflection：2mm Hold Duration：30 s Pressure jig R230 F Deflection 45 45 Product (in mm) MURATA MFG.CO., LTD SpecNo.JELF243A-0047W-01 No. 7.3 Item Vibration 7.4 7.5 Reference Only Specification P3/8 Test Method Chip coil shall not be damaged. Oscillation Frequency：10 to 55 to 10Hz for 1 minute Total Amplitude：1.5mm Testing Time：A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 hours) Solderability The wetting area of the electrode shall be at least 90% covered with new solder coating. Flux：Ethanol solution of rosin, 25(wt)% (Immersed for 5s to 10s) Solder：Sn-3.0Ag-0.5Cu Pre-Heating：150±10°C / 60 to 90seconds Solder Temperature：240±5°C Immersion Time：3±1 s Resistance to Soldering Heat Appearance：No damage Inductance Change：within ±5% Flux：Ethanol solution of rosin, 25(wt)% (Immersed for 5s to 10s) Solder：Sn-3.0Ag-0.5Cu Pre-Heating：150±10°C / 60 to 90seconds Solder Temperature：270±5°C Immersion Time：10±1 s Then measured after exposure in the room condition for 24±2 hours. 8.Environmental Performance (It shall be soldered on the substrate.) No. 8.1 Item Heat Resistance Specification 8.2 Cold Resistance Temperature：-40±2°C Time：1000h (+48h , -0h) Then measured after exposure in the room condition for 24±2 hours. 8.3 Humidity Temperature：40±2°C Humidity：90 to 95%(RH) Time：1000h (+48h , -0h) Then measured after exposure in the room condition for 24±2 hours. 8.4 Temperature Cycle 1 cycle： 1 step：-40±2°C / 30±3 minutes 2 step：Ordinary temp. / 10 to 15 minutes 3 step：+85±2°C / 30±3 min 4 step：Ordinary temp. / 10 to 15 minutes Total of 10 cycles Then measured after exposure in the room condition for 24±2 hours. Appearance：No damage Inductance Change：within ± 5% DC Resistance Change：within ± 5% Test Method Temperature：85±2°C Time：1000h (+48h , -0h) Then measured after exposure in the room condition for 24±2 hours. MURATA MFG.CO., LTD Reference Only SpecNo.JELF243A-0047W-01 P4/8 9. Specification of Packaging 2.0±0.05 4.0±0.1 6.7±0.1 5.5±0.05  1.5 -0 6.7±0.1 (0.4) 0.4±0.1 12.0±0.2 +0.1 1.75±0.1 9.1 Appearance and Dimensions of plastic tape 8.0±0.1 Direction of feed (in mm) 5.6±0.2 Dimension of the Cavity is measured at the bottom side. 9.2 Specification of Taping (1) Packing quantity (standard quantity) 350 pcs / reel (2) Packing Method Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape. (3) Sprocket hole The sprocket holes are to the right as the tape is pulled toward the user. (4) Spliced point Plastic tape and Cover tape has no spliced point. (5) Missing components number Missing components number within 0.025 % of the number per reel or 1 pc., whichever is greater, and are not continuous. The specified quantity per reel is kept. 9.3 Pull Strength Embossed carrier tape 10N min. Cover tape 5N min. 9.4 Peeling off force of cover tape 165 to 180 degree Speed of Peeling off 300 mm / min Peeling off force 0.1 to 0.5N (minimum value is typical) F Plastic tape 9.5 Dimensions of Leader-tape, Trailer and Reel There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows. Trailer : 160 min. 2.0±0.5 Leader Label 190 min 210 min Empty tape Cover tape  13.0±0.2  60± 1 0  21.0±0.8 13.0±1 0 Direction of feed 17.0±1.4 (in mm) 0  180± 3 MURATA MFG.CO., LTD Cover tape SpecNo.JELF243A-0047W-01 Reference Only P5/8 9.6 Marking for reel Customer part number, MURATA part number, Inspection number(1), RoHS marking(2), Quantity etc ･･･ 1) □□ OOOO  (1) (2) (3) (1) Factory Code (2) Date First digit : Year / Last digit of year Second digit : Month / Jan. to Sep.  1 to 9, Oct. to Dec.  O, N, D Third, Fourth digit : Day (3) Serial No. 2) « Expression of RoHS marking » ROHS – Y (△) (1) (2) (1) RoHS regulation conformity (2) MURATA classification number 9.7 Marking for Outside package (corrugated paper box) Customer name, Purchasing order number, Customer part number, MURATA part number, RoHS Marking (2) , Quantity, etc ･･･ 9.8. Specification of Outer Case Outer Case Dimensions (mm) Label H W D H Standard Reel Quantity in Outer Case (Reel) 186 186 93 5 Above Outer Case size is typical. It depends on a quantity of an order D W 10. Caution 10.1 Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (6) Transportation equipment (vehicles, trains, ships, etc.) (7) Traffic signal equipment (8) Disaster prevention / crime prevention equipment (9) Data-processing equipment (10) Applications of similar complexity and /or reliability requirements to the applications listed in the above (1) Aircraft equipment (2) Aerospace equipment (3) Undersea equipment (4) Power plant control equipment (5) Medical equipment 10.2 Corrosive gas Please refrain from use since contact with environments with corrosive gases (sulfur gas [hydrogen sulfide, sulfur dioxide, etc.], chlorine, ammonia, etc.) or oils (cutting oil, silicone oil, etc.) that have come into contact with the previously stated corrosive gas environment will result in deterioration of product quality or an open from deterioration due to corrosion of product electrode, etc. We will not bear any responsibility for use under these environments. 11. Notice This product is designed for solder mounting. Please consult us in advance for applying other mounting method such as conductive adhesive. 11.1 Land pattern designing (Reflow Soldering) Recommended land pattern for reflow soldering is as follows: It has been designed for Electric characteristics and solderability. Please follow the recommended patterns. Otherwise, their performance which includes electrical performance or solderability may be affected, or result to "position shift" in soldering process. 3.5 8.0 3.0 2.0 3.0 in mm MURATA MFG.CO., LTD SpecNo.JELF243A-0047W-01 Reference Only P6/8 11.2 Flux, Solder ・Use rosin-based flux. Flux ・Don’t use highly acidic flux with halide content exceeding 0.2(wt)% (chlorine conversion value). ・Don’t use water-soluble flux. ・Use Sn-3.0Ag-0.5Cu solder Solder ・Standard thickness of solder paste : 200μm to 300μm Other flux (except above) Please contact us for details, then use. 11.3 soldering conditions (Reflow) ・Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to 150°C max. Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max. Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality. ・Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the deterioration of product quality. Temp. (℃) 260℃ 245℃±3℃ 220℃ 230℃ Limit Profile 180 150 Standard Profile 30s～60s 60s max. 90s±30s Time. (s) Standard Profile Pre-heating Heating Peak temperature Cycle of reflow Limit Profile 150～180°C 、90s±30s above 220°C、30s～60s above 230°C、60s max. 245±3°C 260°C, 10s 2 times 1 time 11.4 Reworking with soldering iron. The following conditions must be strictly followed when using a soldering iron. Pre-heating 150°C,1 min Tip temperature 350°C max. Soldering iron output 80W max. Tip diameter φ3mm max. Soldering time 3(+1,-0)s Times 2 times Note : Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the products due to the thermal shock. 11.5 Solder Volume ・Solder shall be used not to be exceeded the upper limits as shown below. ・Accordingly increasing the solder volume, the mechanical stress to Chip is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. Upper Limit Recommendable T t MURATA MFG.CO., LTD 1/3T≦t≦T (T: Lower flange thickness) Reference Only SpecNo.JELF243A-0047W-01 P7/8 11.6 Product's location The following shall be considered when designing and laying out P.C.B.’s. (1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board. ［Products direction］ a Products shall be located in the sideways direction (Length:a (2) Add slits in the board separation part. A > B (3) Keep the mounting position of the component away from the board separation surface. A > C Seam b A C B D Slit D 1 1 A > D is valid when stress is added vertically to the perforation as with Hand Separation. If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid. Length:a b a (3) Mounting Components Near Screw Holes When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the tightening of the screw. Mount the component in a position as far away from the screw holes as possible. Screw Hole Recommended 11.7 Cleaning Conditions Products shall be cleaned on the following conditions. (1) Cleaning temperature shall be limited to 40°C max. (2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance phenomenon at the mounted products and P.C.B.. Power : 20 W / l max. Frequency : 28kHz to 40kHz Time : 5 minutes max. (3) Cleaner 1. Alternative cleaner ・Isopropyl alcohol (IPA) 2. Aqueous agent Aqueous agent should not be used because it may cause quality deterioration. (4) Other cleaning Please contact us. 11.8 Resin coating The inductance value may change due to high cure-stress of resin to be used for coating/molding products. An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some operating condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful attention when you select resin in case of coating/molding the products with the resin. Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products mounted on your board. 11.9 Caution for use Sharp material such as a pair of tweezers or other material such as bristles of cleaning brush, shall not be touched to the winding portion to prevent the breaking of wire. MURATA MFG.CO., LTD SpecNo.JELF243A-0047W-01 Reference Only P8/8 11.10 Handling of a substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the product. Bending Twisting 11.11 Storage and Handling Requirements (1) Storage period Use the products within 12 months after delivered. Solderability should be checked if this period is exceeded. (2) Storage conditions ・Products should be stored in the warehouse on the following conditions. Temperature : -10 ~ 40°C Humidity : 15 to 85% relative humidity No rapid change on temperature and humidity ・The electrode of the products is coated with solder. Don't keep products in corrosive gases such as sulfur,chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability. ・Products should not be stored on bulk packaging condition to prevent the chipping of the core and the breaking of winding wire caused by the collision between the products. ・Products should be stored on the palette for the prevention of the influence from humidity, dust and so on. ・Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. (3) Handling Condition Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 12. Note (1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2) You are requested not to use our product deviating from the reference specifications. (3) The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG.CO., LTD