LQH88PN470M38L

Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet Chip Inductor (Chip Coil) 1 Power Inductor (Wire Wound Type) LQH88P Series (3131 Size) ■ Dimensions ■ Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 250 K 330mm Embossed Tape 1000 (0.3) 3.8±0.2 8.0±0.2 1.9±0.2 1.9±0.2 1.0 (typ.) 3.0 (typ.) 8.0±0.2 8.0±0.2 (in mm) ■ Rated Value (p: packaging code) Inductance Rated Current (Based on Inductance Change) Rated Current (Based on Temperature Rise) DC Resistance Self Resonance Frequency (min.) LQH88PN1R0N38p 1.0µH±30% 11.20A 8.00A 0.006ohm±30% 100MHz LQH88PN1R5N38p 1.5µH±30% 8.50A 7.10A 0.008ohm±30% 60MHz LQH88PN2R2N38p 2.2µH±30% 8.00A 6.40A 0.009ohm±30% 50MHz LQH88PN3R3N38p 3.3µH±30% 7.00A 5.00A 0.013ohm±30% 35MHz LQH88PN4R7N38p 4.7µH±30% 6.00A 4.20A 0.017ohm±30% 30MHz LQH88PN6R8N38p 6.8µH±30% 4.50A 3.80A 0.022ohm±30% 20MHz LQH88PN100M38p 10µH±20% 3.60A 3.15A 0.029ohm±30% 18MHz LQH88PN150M38p 15µH±20% 3.00A 2.45A 0.041ohm±30% 13MHz LQH88PN220M38p 22µH±20% 2.70A 2.25A 0.066ohm±30% 10MHz LQH88PN330M38p 33µH±20% 1.90A 1.75A 0.095ohm±30% 9MHz LQH88PN470M38p 47µH±20% 1.50A 1.45A 0.157ohm±30% 7MHz LQH88PN680M38p 68µH±20% 1.25A 1.10A 0.190ohm±30% 7MHz LQH88PN101M38p 100µH±20% 1.00A 1.00A 0.265ohm±30% 4MHz Part Number Test Frequency: 100kHz Class of Magnetic Shield: Magnetic shield of magnetic powder in resin Operating Temperature Range (Self-temperature rise is included): -40°C to +125°C Operating Temperature Range (Self-temperature rise is not included): -40°C to +85°C Only for reflow soldering. Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet 2 Continued from the preceding page. ■ Notice (Rated Current) (Based on Inductance Change) When Rated Current is applied to the Products, Inductance will be within +-30% of nominal Inductance value. (Based on Temperature Rise) When Rated Current is applied to the Products, self-generation of heat will rise to 40°C or less. ■ Inductance-Frequency Characteristics (Typ.) ■ Inductance-Current Characteristics (Typ.) 100 10000 Inductance (µH) 100 10 Inductance (µH) 100µH 68µH 47µH 33µH 22µH 15µH 10µH 6.8µH 4.7µH 3.3µH 2.2µH 1.5µH 1.0µH 1000 100µH 68µH 33µH 22µH 15µH 10µH 6.8µH 10 47µH 4.7µH 3.3µH 2.2µH 1.5µH 1.0µH 1 1 0.1 0.1 1 10 Frequency (MHz) 100 0.1 10 1000 100 1000 Current (mA) 10000 100000 ■ Temperature Rise Characteristics (Typ.) 40 100µH 33µH 68µH 22µH 3.3µH 2.2µH 1.5µH 1.0µH 47µH 15µH Temperature Rise (°C) 30 10µH 6.8µH 4.7µH 20 10 0 0 2000 4000 6000 Current (mA) 8000 10000 ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/