LQP03TN2N7C02D

Spec No.: JELF243C_0015V-01 P1/14 CHIP COILS (CHIP INDUCTORS) LQP03TN□□□□02□ REFERENCE SPECIFICATION 1. Scope This reference specification applies to chip coils (chip inductors) LQP03TN_02 series for general electronic equipment. 2. Part Numbering (Ex.) LQ P 03 Product Structure Dimension ID (L × W) T N 0N6 B 0 2 Application Category Inductance Tolerance Performance Electrode and specification characteristic *B: Bulk packing is also available (taping condition: however, products without reels are put in plastic bags). D Packaging D: taping *B: bulk 3. Part Number and Rating Operating temperature range Storage temperature range -55°C to +125°C -55°C to +125°C Inductance Customer Part number Murata Part number Nominal value (nH) Q (Min.) Tolerance DC resistance (Ω max.) Self-resonant frequency (MHz) Lower limit *Typical value Rated current (mA) LQP03TN0N6B02D 0.6 B: ±0.1 nH 14 0.07 20000 20000 850 LQP03TN0N6C02D 0.6 C: ±0.2 nH 14 0.07 20000 20000 850 LQP03TN0N7B02D 0.7 B: ±0.1 nH 14 0.08 20000 20000 800 LQP03TN0N7C02D 0.7 C: ±0.2 nH 14 0.08 20000 20000 800 LQP03TN0N8B02D 0.8 B: ±0.1 nH 14 0.08 18000 20000 800 LQP03TN0N8C02D 0.8 C: ±0.2 nH 14 0.08 18000 20000 800 LQP03TN0N9B02D 0.9 B: ±0.1 nH 14 0.10 18000 20000 750 LQP03TN0N9C02D 0.9 C: ±0.2 nH 14 0.10 18000 20000 750 LQP03TN1N0B02D 1.0 B: ±0.1 nH 14 0.10 17000 20000 750 LQP03TN1N0C02D 1.0 C: ±0.2 nH 14 0.10 17000 20000 750 LQP03TN1N1B02D 1.1 B: ±0.1 nH 14 0.10 17000 20000 750 LQP03TN1N1C02D 1.1 C: ±0.2 nH 14 0.10 17000 20000 750 LQP03TN1N2B02D 1.2 B: ±0.1 nH 14 0.10 17000 20000 750 LQP03TN1N2C02D 1.2 C: ±0.2 nH 14 0.10 17000 20000 750 LQP03TN1N3B02D 1.3 B: ±0.1 nH 14 0.15 17000 20000 600 LQP03TN1N3C02D 1.3 C: ±0.2 nH 14 0.15 17000 20000 600 LQP03TN1N4B02D 1.4 B: ±0.1 nH 14 0.15 16000 19600 600 LQP03TN1N4C02D 1.4 C: ±0.2 nH 14 0.15 16000 19600 600 LQP03TN1N5B02D 1.5 B: ±0.1 nH 14 0.15 15000 17900 600 LQP03TN1N5C02D 1.5 C: ±0.2 nH 14 0.15 15000 17900 600 LQP03TN1N6B02D 1.6 B: ±0.1 nH 14 0.15 15000 20000 600 LQP03TN1N6C02D 1.6 C: ±0.2 nH 14 0.15 15000 20000 600 LQP03TN1N7B02D 1.7 B: ±0.1 nH 14 0.15 15000 19100 600 LQP03TN1N7C02D 1.7 C: ±0.2 nH 14 0.15 15000 19100 600 LQP03TN1N8B02D 1.8 B: ±0.1 nH 14 0.15 15000 17700 600 LQP03TN1N8C02D 1.8 C: ±0.2 nH 14 0.15 15000 17700 600 LQP03TN1N9B02D 1.9 B: ±0.1 nH 14 0.15 12500 15100 600 LQP03TN1N9C02D 1.9 C: ±0.2 nH 14 0.15 12500 15100 600 LQP03TN2N0B02D 2.0 B: ±0.1 nH 14 0.15 12500 14800 600 MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P2/14 Inductance Customer Part number Murata Part number Q (Min.) DC resistance (Ω max.) Self-resonant frequency (MHz) Rated current (mA) Nominal value (nH) Tolerance LQP03TN2N0C02D 2.0 C: ±0.2 nH 14 0.15 12500 14800 600 LQP03TN2N1B02D 2.1 B: ±0.1 nH 14 0.15 11000 13900 600 LQP03TN2N1C02D 2.1 C: ±0.2 nH 14 0.15 11000 13900 600 LQP03TN2N2B02D 2.2 B: ±0.1 nH 14 0.15 11000 13400 600 LQP03TN2N2C02D 2.2 C: ±0.2 nH 14 0.15 11000 13400 600 Lower limit *Typical value LQP03TN2N3B02D 2.3 B: ±0.1 nH 14 0.20 10000 12900 500 LQP03TN2N3C02D 2.3 C: ±0.2 nH 14 0.20 10000 12900 500 LQP03TN2N4B02D 2.4 B: ±0.1 nH 14 0.20 10000 12200 500 LQP03TN2N4C02D 2.4 C: ±0.2 nH 14 0.20 10000 12200 500 LQP03TN2N5B02D 2.5 B: ±0.1 nH 14 0.20 10000 12200 500 LQP03TN2N5C02D 2.5 C: ±0.2 nH 14 0.20 10000 12200 500 LQP03TN2N6B02D 2.6 B: ±0.1 nH 14 0.20 10000 13300 500 LQP03TN2N6C02D 2.6 C: ±0.2 nH 14 0.20 10000 13300 500 LQP03TN2N7B02D 2.7 B: ±0.1 nH 14 0.20 10000 13000 500 LQP03TN2N7C02D 2.7 C: ±0.2 nH 14 0.20 10000 13000 500 LQP03TN2N8B02D 2.8 B: ±0.1 nH 14 0.20 9500 11800 500 LQP03TN2N8C02D 2.8 C: ±0.2 nH 14 0.20 9500 11800 500 LQP03TN2N9B02D 2.9 B: ±0.1 nH 14 0.20 9500 12400 500 LQP03TN2N9C02D 2.9 C: ±0.2 nH 14 0.20 9500 12400 500 LQP03TN3N0B02D 3.0 B: ±0.1 nH 14 0.25 9500 11900 450 LQP03TN3N0C02D 3.0 C: ±0.2 nH 14 0.25 9500 11900 450 LQP03TN3N1B02D 3.1 B: ±0.1 nH 14 0.25 8000 11300 450 LQP03TN3N1C02D 3.1 C: ±0.2 nH 14 0.25 8000 11300 450 LQP03TN3N2B02D 3.2 B: ±0.1 nH 14 0.25 8000 10600 450 LQP03TN3N2C02D 3.2 C: ±0.2 nH 14 0.25 8000 10600 450 LQP03TN3N3B02D 3.3 B: ±0.1 nH 14 0.25 8000 10900 450 LQP03TN3N3C02D 3.3 C: ±0.2 nH 14 0.25 8000 10900 450 LQP03TN3N4B02D 3.4 B: ±0.1 nH 14 0.25 7000 9400 450 LQP03TN3N4C02D 3.4 C: ±0.2 nH 14 0.25 7000 9400 450 LQP03TN3N5B02D 3.5 B: ±0.1 nH 14 0.25 7000 9600 450 LQP03TN3N5C02D 3.5 C: ±0.2 nH 14 0.25 7000 9600 450 LQP03TN3N6B02D 3.6 B: ±0.1 nH 14 0.30 6000 9500 400 LQP03TN3N6C02D 3.6 C: ±0.2 nH 14 0.30 6000 9500 400 LQP03TN3N7B02D 3.7 B: ±0.1 nH 14 0.30 6000 8200 400 LQP03TN3N7C02D 3.7 C: ±0.2 nH 14 0.30 6000 8200 400 LQP03TN3N8B02D 3.8 B: ±0.1 nH 14 0.30 6000 8100 400 LQP03TN3N8C02D 3.8 C: ±0.2 nH 14 0.30 6000 8100 400 LQP03TN3N9B02D 3.9 B: ±0.1 nH 14 0.30 5700 7900 400 LQP03TN3N9C02D 3.9 C: ±0.2 nH 14 0.30 5700 7900 400 LQP03TN4N0B02D 4.0 B: ±0.1 nH 14 0.40 5300 8600 350 LQP03TN4N0C02D 4.0 C: ±0.2 nH 14 0.40 5300 8600 350 LQP03TN4N1B02D 4.1 B: ±0.1 nH 14 0.40 5300 8400 350 LQP03TN4N1C02D 4.1 C: ±0.2 nH 14 0.40 5300 8400 350 LQP03TN4N2B02D 4.2 B: ±0.1 nH 14 0.40 5300 8600 350 MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P3/14 Inductance Customer Part number Murata Part number Q (Min.) DC resistance (Ω max.) Self-resonant frequency (MHz) Rated current (mA) Nominal value (nH) Tolerance LQP03TN4N2C02D 4.2 C: ±0.2 nH 14 0.40 5300 8600 350 LQP03TN4N3H02D 4.3 H: ±3% 14 0.40 5300 9800 350 Lower limit *Typical value LQP03TN4N3J02D 4.3 J: ±5% 14 0.40 5300 9800 350 LQP03TN4N7H02D 4.7 H: ±3% 14 0.40 4400 8800 350 LQP03TN4N7J02D 4.7 J: ±5% 14 0.40 4400 8800 350 LQP03TN5N1H02D 5.1 H: ±3% 14 0.40 4200 8600 350 LQP03TN5N1J02D 5.1 J: ±5% 14 0.40 4200 8600 350 LQP03TN5N6H02D 5.6 H: ±3% 14 0.40 4000 8000 350 LQP03TN5N6J02D 5.6 J: ±5% 14 0.40 4000 8000 350 LQP03TN6N2H02D 6.2 H: ±3% 14 0.60 4000 7900 300 LQP03TN6N2J02D 6.2 J: ±5% 14 0.60 4000 7900 300 LQP03TN6N8H02D 6.8 H: ±3% 14 0.60 3900 8000 300 LQP03TN6N8J02D 6.8 J: ±5% 14 0.60 3900 8000 300 LQP03TN7N5H02D 7.5 H: ±3% 14 0.60 3700 6700 300 LQP03TN7N5J02D 7.5 J: ±5% 14 0.60 3700 6700 300 LQP03TN8N2H02D 8.2 H: ±3% 14 0.70 3600 6600 250 LQP03TN8N2J02D 8.2 J: ±5% 14 0.70 3600 6600 250 LQP03TN9N1H02D 9.1 H: ±3% 14 0.70 3300 5900 250 LQP03TN9N1J02D 9.1 J: ±5% 14 0.70 3300 5900 250 LQP03TN10NH02D 10 H: ±3% 14 0.70 3200 5800 250 LQP03TN10NJ02D 10 J: ±5% 14 0.70 3200 5800 250 LQP03TN11NH02D 11 H: ±3% 14 0.80 2900 5400 250 LQP03TN11NJ02D 11 J: ±5% 14 0.80 2900 5400 250 LQP03TN12NH02D 12 H: ±3% 12 0.70 2900 4300 250 LQP03TN12NJ02D 12 J: ±5% 12 0.70 2900 4300 250 LQP03TN13NH02D 13 H: ±3% 12 0.80 2600 4300 250 LQP03TN13NJ02D 13 J: ±5% 12 0.80 2600 4300 250 LQP03TN15NH02D 15 H: ±3% 12 0.70 2600 3800 250 LQP03TN15NJ02D 15 J: ±5% 12 0.70 2600 3800 250 LQP03TN16NH02D 16 H: ±3% 12 0.95 2200 3700 200 LQP03TN16NJ02D 16 J: ±5% 12 0.95 2200 3700 200 LQP03TN18NH02D 18 H: ±3% 12 0.80 2200 3400 200 LQP03TN18NJ02D 18 J: ±5% 12 0.80 2200 3400 200 LQP03TN20NH02D 20 H: ±3% 12 2.30 2200 3600 150 LQP03TN20NJ02D 20 J: ±5% 12 2.30 2200 3600 150 LQP03TN22NH02D 22 H: ±3% 12 1.90 2200 3300 150 LQP03TN22NJ02D 22 J: ±5% 12 1.90 2200 3300 150 LQP03TN24NH02D 24 H: ±3% 12 2.30 2000 3200 140 LQP03TN24NJ02D 24 J: ±5% 12 2.30 2000 3200 140 LQP03TN27NH02D 27 H: ±3% 12 2.30 2000 2900 140 LQP03TN27NJ02D 27 J: ±5% 12 2.30 2000 2900 140 LQP03TN30NH02D 30 H: ±3% 9 2.95 1700 2700 120 LQP03TN30NJ02D 30 J: ±5% 9 2.95 1700 2700 120 LQP03TN33NH02D 33 H: ±3% 9 2.95 1700 2600 120 MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P4/14 Inductance Customer Part number Murata Part number Nominal value (nH) Q (Min.) Tolerance DC resistance (Ω max.) Self-resonant frequency (MHz) Lower limit *Typical value Rated current (mA) LQP03TN33NJ02D 33 J: ±5% 9 2.95 1700 2600 120 LQP03TN36NH02D 36 H: ±3% 9 3.00 1500 2400 120 LQP03TN36NJ02D 36 J: ±5% 9 3.00 1500 2400 120 LQP03TN39NH02D 39 H: ±3% 9 3.00 1500 2200 120 LQP03TN39NJ02D 39 J: ±5% 9 3.00 1500 2200 120 LQP03TN43NH02D 43 H: ±3% 9 3.60 1300 2200 100 LQP03TN43NJ02D 43 J: ±5% 9 3.60 1300 2200 100 LQP03TN47NH02D 47 H: ±3% 9 3.60 1300 2000 100 LQP03TN47NJ02D 47 J: ±5% 9 3.60 1300 2000 100 LQP03TN51NH02D 51 H: ±3% 9 3.90 1200 2000 100 LQP03TN51NJ02D 51 J: ±5% 9 3.90 1200 2000 100 LQP03TN56NH02D 56 H: ±3% 9 3.90 1200 2000 100 LQP03TN56NJ02D 56 J: ±5% 9 3.90 1200 2000 100 LQP03TN62NH02D 62 H: ±3% 8 8 1100 1800 100 LQP03TN62NJ02D 62 J: ±5% 8 8 1100 1800 100 LQP03TN68NH02D 68 H: ±3% 8 8 1100 1500 100 LQP03TN68NJ02D 68 J: ±5% 8 8 1100 1500 100 LQP03TN75NJ02D 75 H: ±3% 8 10 1000 1400 100 LQP03TN75NH02D 75 J: ±5% 8 10 1000 1400 100 LQP03TN82NH02D 82 H: ±3% 8 10 1000 1400 100 LQP03TN82NJ02D 82 J: ±5% 8 10 1000 1400 100 LQP03TN91NH02D 91 H: ±3% 8 10 900 1300 80 LQP03TN91NJ02D 91 J: ±5% 8 10 900 1300 80 LQP03TNR10H02D 100 H: ±3% 8 10 900 1300 80 LQP03TNR10J02D 100 J: ±5% 8 10 900 1300 80 LQP03TNR11H02D 110 H: ±3% 8 12 800 1100 80 LQP03TNR11J02D 110 J: ±5% 8 12 800 1100 80 LQP03TNR12H02D 120 H: ±3% 8 12 800 1100 80 LQP03TNR12J02D 120 J: ±5% 8 12 800 1100 80 LQP03TNR13H02D 130 H: ±3% 5 9 650 960 80 LQP03TNR13J02D 130 J: ±5% 5 9 650 960 80 LQP03TNR15H02D 150 H: ±3% 5 9 650 880 80 LQP03TNR15J02D 150 J: ±5% 5 9 650 880 80 LQP03TNR16H02D 160 H: ±3% 5 11 600 840 70 LQP03TNR16J02D 160 J: ±5% 5 11 600 840 70 LQP03TNR18H02D 180 H: ±3% 5 11 600 790 70 LQP03TNR18J02D 180 J: ±5% 5 11 600 790 70 LQP03TNR20H02D 200 H: ±3% 5 13 500 750 60 LQP03TNR20J02D 200 J: ±5% 5 13 500 750 60 LQP03TNR22H02D 220 H: ±3% 5 13 500 710 60 LQP03TNR22J02D 220 J: ±5% 5 13 500 710 60 LQP03TNR24H02D 240 H: ±3% 5 15 450 630 60 LQP03TNR24J02D 240 J: ±5% 5 15 450 630 60 LQP03TNR27H02D 270 H: ±3% 5 15 450 580 60 MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P5/14 Inductance Customer Part number Murata Part number LQP03TNR27J02D * Typical value is actual performance. Nominal value (nH) Tolerance 270 J: ±5% Q (Min.) DC resistance (Ω max.) 5 15 Self-resonant frequency (MHz) Lower limit *Typical value 450 580 4. Testing Conditions Unless otherwise specified Temperature: ordinary temperature (15°C to 35°C) Humidity: ordinary humidity [25% to 85% (RH)] In case of doubt Temperature: 20°C±2°C Humidity: 60% to 70% (RH) Atmospheric pressure: 86 kPa to 106 kPa 5. Appearance and Dimensions Unit mass (typical value): 0.2 mg 6. Marking MURATA MFG CO., LTD Rated current (mA) 60 Spec No.: JELF243C_0015V-01 P6/14 7. Electrical Performance No. Item 7.1 Inductance 7.2 Q Specification Meet chapter 3 ratings. Meet chapter 3 ratings. Test method Measuring equipment: Keysight E4991A or the equivalent Measuring frequency: 500 MHz 0.6 nH to 30 nH 300 MHz 33 nH to 120 nH 100 MHz 130 nH to 270 nH Measuring conditions: Measurement signal level: Approx. 0 dBm Measurement terminal distance: 0.2 mm Electrical length: 10 mm Weight: Approx. 1 N to 5 N Measuring fixture: Keysight 16197A Position the chip coil under test as shown in the measuring example below and connect it to the electrode by applying weight. Measurement example: 7.3 DC resistance 7.4 Self-resonant frequency 7.5 Rated current Meet chapter 3 ratings. Meet chapter 3 ratings. Product temperature rise: 25°C max. Measuring method: see "Electrical performance: Measuring method for inductance/Q" in the Appendix. Measuring equipment: digital multimeter Measuring equipment: Keysight N5230A or the equivalent Apply the rated current specified in chapter 3. 8. Mechanical Performance No. Item 8.1 Shear test Specification Test method No significant mechanical damage or no Test substrate: glass-epoxy substrate sign of electrode peeling off shall be Applying force: 2 N observed. Holding time: 5 s±1 s Force application direction: 8.2 Bending test No significant mechanical damage or no Test substrate: glass-epoxy substrate (100 mm × 40 sign of electrode peeling off shall be mm × 0.8 mm) observed. Pressurizing speed: 1 mm/s Pressure jig: R340 Deflection: 1 mm Holding time: 30 s MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 No. Item 8.3 Vibration 8.4 Solderability 8.5 Resistance to soldering heat P7/14 Specification Appearance shall have no significant mechanical damage. Inductance change rate: within ±10% Test method Oscillation frequency: 10 Hz to 2000 Hz to 10 Hz, for approx. 20 min Total amplitude: total amplitude of 1.5 mm or acceleration amplitude of 196 m/s2, whichever is smaller Test time: 3 directions perpendicular to each other, 2 h for each direction (6 h in total) 90% or more of the outer electrode shall Flux: immersed in ethanol solution with a rosin content be covered with new solder seamlessly. of 25(wt)% for 5 s to 10 s Solder: Sn-3.0Ag-0.5Cu solder Pre-heating: 150°C±10°C/60 s to 90 s Solder temperature: 240°C±5°C Immersion time: 3 s±1 s Appearance: No significant mechanical Flux: immersed in ethanol solution with a rosin content damage shall be observed. of 25(wt)% for 5 s to 10 s Inductance change rate: within ±10% Solder: Sn-3.0Ag-0.5Cu solder Pre-heating: 150°C±10°C/60 s to 90 s Solder temperature: 260°C±5°C Immersion time: 5 s±1 s Post-treatment: left at a room condition for 24 h±2 h 9. Environmental Performance The product is soldered on a glass-epoxy substrate for test. No. Item Specification 9.1 Heat resistance Appearance: No significant mechanical damage shall be observed. Inductance change rate: within ±10% 9.2 Cold resistance Appearance: No significant mechanical damage shall be observed. Inductance change rate: within ±10% 9.3 Humidity Appearance: No significant mechanical damage shall be observed. Inductance change rate: within ±10% 9.4 Temperature cycle Appearance: No significant mechanical damage shall be observed. Inductance change rate: within ±10% Test method Temperature: 125°C±2°C Test time: 1000 h (+48 h, -0 h) Post-treatment: left at a room condition for 24 h±2 h Temperature: -55°C±3°C Test time: 1000 h (+48 h, -0 h) Post-treatment: left at a room condition for 24 h±2 h Temperature: 40°C±2°C Humidity: 90% (RH) to 95% (RH) Test time: 1000 h (+48 h, -0 h) Post-treatment: left at a room condition for 24 h±2 h Single cycle conditions: Step 1: -55°C±2°C/30 min±3 min Step 2: ordinary temperature/10 min to 15 min Step 3: +125°C±2°C/30 min±3 min Step 4: ordinary temperature/10 min to 15 min Number of testing: 10 cycles Post-treatment: left at a room condition for 24 h±2 h 10. Specification of Packaging 10.1 Appearance and dimensions of tape (8 mm width/paper tape) A 0.35±0.03 B 0N6 to 62N、R13 to R27：0.67±0.03 68N to R12：0.65±0.03 t 0.55 max. (in mm) MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P8/14 10.2 Taping specifications Packing quantity (Standard quantity) 15000 pcs/reel Packing method The products are placed in cavities of a carrier tape and sealed by a cover tape (top tape and bottom tape when the cavities of the carrier tape are punched type). Feed hole position The feed holes on the carrier tape are on the right side when the cover tape (top tape when the cavities of the carrier tape are punched type) is pulled toward the user. Joint The carrier tape and cover tape (top tape when the cavities of the carrier tape are punched type) are seamless. Number of missing products Number of missing products within 0.1% of the number per reel or 1 pc., whichever is greater, and are not continuous. The specified quantity per reel is kept. 10.3 Break down force of tape Cover tape (or top tape) 5 N min. Bottom tape (only when the cavities of the carrier tape are punched type) 5 N min. 10.4 Peeling off force of tape Speed of peeling off Peeling off force 300 mm/min 0.1 N to 0.6 N (The lower limit is for typical value.) 10.5 Dimensions of leader section, trailer section and reel A vacant section is provided in the leader (start) section and trailer (end) section of the tape for the product. The leader section is further provided with an area consisting only of the cover tape (or top tape). (See the diagram below.) MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P9/14 10.6 Marking for reel Customer part number, Murata part number, inspection number (*1), RoHS marking (*2), quantity, etc. *1 Expression of inspection No.: (1) Factory code  (2) Date □□ ○○○○ First digit: year/last digit of year (1) (2) (3) Second digit: month/Jan. to Sep.→1 to 9, Oct. to Dec.→O, N, D Third, Fourth digit: day (3) Serial No. *2 Expression of RoHS marking: (1) RoHS regulation conformity ROHSY () (2) Murata classification number (1) (2) 10.7 Marking on outer box (corrugated box) Customer name, purchasing order number, customer part number, Murata part number, RoHS marking (*2), quantity, etc. 10.8 Specification of outer box Label H D W 11. Dimensions of outer box (mm) W D H 186 186 93 Standard reel quantity in outer box (reel) 5 * Above outer box size is typical. It depends on a quantity of an order. Caution 11.1 Restricted applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1) Aircraft equipment (2) Aerospace equipment (3) Undersea (4) Power plant control equipment equipment (5) Medical equipment (6) Transportation equipment (vehicles, (7) Traffic signal (8) Disaster/crime trains, ships, etc.) equipment prevention equipment (9) Data-processing (10) Applications of similar complexity and/or reliability equipment requirements to the applications listed in the above 11.2 Precautions on rating Avoid using in exceeded the rated temperature range, rated voltage, or rated current. Usage when the ratings are exceeded could lead to wire breakage, burning, or other serious fault. 11.3 Inrush current If an inrush current (or pulse current or rush current) that significantly exceeds the rated current is applied to the product, overheating could occur, resulting in wire breakage, burning, or other serious fault. 12. Precautions for Use This product is for use only with reflow soldering. It is designed to be mounted by soldering. If you want to use other mounting method, for example, using a conductive adhesive, please consult us beforehand. Also, if repeatedly subjected to temperature cycles or other thermal stress, due to the difference in the coefficient of thermal expansion with the mounting substrate, the solder (solder fillet part) in the mounting part may crack. The occurrence of cracks due to thermal stress is affected by the size of the land where mounted, the solder volume, and the heat dissipation of the mounting substrate. Carefully design it when a large change in ambient temperature is assumed. MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P10/14 12.1. Land dimensions The following diagram shows the recommended land dimensions for reflow soldering: a 0.2 to 0.3 b 0.8 to 0.9 c 0.2 to 0.3 (in mm) 12.2 Flux and solder used Flux • Use a rosin-based flux. • Do not use a highly acidic flux with a halide content exceeding 0.2(wt)% (chlorine conversion value). • Do not use a water-soluble flux. Solder • Use Sn-3.0Ag-0.5Cu solder. • Standard thickness of solder paste: 100 μm to 150 μm If you want to use a flux other than the above, please consult our technical department. 12.3 Soldering conditions (reflow) • Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to 150°C max. Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max. Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality. • Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and/or resulting in the deterioration of product quality. Temp. (℃) 260℃ 245℃±3℃ 220℃ 230℃ Limit Profile 180 150 Standard Profile 30s～60s 60s max. 90s±30s Time. (s) Standard profile Limit profile Pre-heating 150°C to 180°C/90 s±30 s 150°C to 180°C/90 s±30 s Heating Above 220°C/30 s to 60 s Above 230°C/60 s max. 245°C±3°C 260°C/10 s 2 times 2 times Peak temperature Number of reflow cycles MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P11/14 12.4 Reworking with soldering iron The following requirements must be met to rework a soldered product using a soldering iron. Item Requirement Pre-heating 150°C/approx. 1 min Tip temperature of soldering iron 350°C max. Power consumption of soldering iron 80 W max. Tip diameter of soldering iron Soldering time ø3 mm max. 3 s (+1 s, -0 s) Number of reworking operations 2 times max. * Avoid a direct contact of the tip of the soldering iron with the product. Such a direction contact may cause cracks in the ceramic body due to thermal shock. 12.5 Solder volume Solder shall be used not to be exceeded the upper limits as shown below. An increased solder volume increases mechanical stress on the product. Exceeding solder volume may cause the failure of mechanical or electrical performance. 12.6 Product's location The following shall be considered when designing and laying out PCBs. (1) PCB shall be designed so that products are not subject to mechanical stress due to warping the board. [Products direction] Products shall be located in the sideways direction (length: a < b) to the mechanical stress. a b 〈 Poor example〉 〈 Good example〉 (2) Components location on PCB separation It is effective to implement the following measures, to reduce stress in separating the board. It is best to implement all of the following three measures; however, implement as many measures as possible to reduce stress. Contents of measures Stress level (1) Turn the mounting direction of the component parallel to the board separation surface. A > D*1 (2) Add slits in the board separation part. A>B (3) Keep the mounting position of the component away from the board separation surface. A>C *1 A > D is valid when stress is added vertically to the perforation as with hand separation. If a cutting disc is used, stress will be diagonal to the PCB, therefore A > D is invalid. MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P12/14 (3) Mounting components near screw holes When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the tightening of the screw. Mount the component in a position as far away from the screw holes as possible. 12.7 Handling of substrate (1) The stress applied to the chip varies depending on the material and construction of the mounted substrate. If the coefficients of thermal expansion for the substrate and chip vary significantly, the difference in thermal expansion and shrinkage could cause cracks to form in the chip. We assume that the products are mounted on glass-epoxy substrate. Assessment has not been conducted on substrates where the coefficient of thermal expansion varies significantly from glass-epoxy substrates. If mounting on these substrates, be sure to conduct full assessments before use. (2) After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the product. Also, if mounting on flexible substrates, excessive mechanical stress could be applied to the chip by even slight bending or twisting when handling this substrate, and so please conduct full assessments before use. Bending Twisting 12.8 Cleaning The product shall be cleaned under the following conditions. (1) The cleaning temperature shall be 60°C max. If isopropyl alcohol (IPA) is used, the cleaning temperature shall be 40°C max. (2) Perform ultrasonic cleaning under the following conditions. Exercise caution to prevent resonance phenomenon in mounted products and the PCB. Item Requirement Power Time 20 W/L max. 5 min max. Frequency 28 kHz to 40 kHz (3) Cleaner Alcohol-based cleaner: IPA Aqueous agent: PINE ALPHA ST-100S (4) There shall be no residual flux or residual cleaner. When using aqueous agent, rinse the product with deionized water adequately and completely dry it so that no cleaner is left. * For other cleaning, consult our technical department. MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P13/14 12.9 Storage and transportation Storage period Use the product within 12 months after delivery. If you do not use the product for more than 12 months, check solderability before using it. Storage conditions • The products shall be stored in a room not subject to rapid changes in temperature and humidity. The recommended temperature range is -10°C to +40°C. The recommended relative humidity range is 15% to 85%. Keeping the product in corrosive gases, such as sulfur, chlorine gas or acid may cause the poor solderability. • Do not place the products directly on the floor; they should be placed on a palette so that they are not affected by humidity or dust. • Avoid keeping the products in a place exposed to direct sunlight, heat or vibration. • Do not keep products in bulk packaging. Bulk storage could result in collisions between the products or between the products and other parts, resulting in chipping or wire breakage. • Avoid storing the product by itself bare (i.e. exposed directly to air). Transportation Excessive vibration and impact reduces the reliability of the products. Exercise caution when handling the products. 12.10 Resin coating (including moisture-proof coating) Before applying any resin coating, please consult our technical department. 12.11 Mounting conditions Check the mounting condition before using. Using mounting conditions (nozzles, equipment conditions, etc.) that are not suitable for products may lead to pick up errors, misalignment, or damage to the product. 12.12 Operating environment Do not use this product under the following environmental conditions as it may cause deterioration of product quality. (1) In the corrodible atmosphere such as acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc. (the sea breeze, Cl2, H2S, NH3, SO2, NO2, etc) (2) In the atmosphere where liquid such as organic solvent, may splash on the products. (3) In the atmosphere where the temperature/humidity changes rapidly and it is easy to dew. 12.13 Mounting density If this product is placed near heat-generating products, be sure to implement sufficient heat-dissipating measures. If this product is subjected to a significant amount of heat from other products, this could adversely affect product quality, resulting in a circuit malfunction or failure of the mounted section. Also, be sure that the product is used in a manner so that the heat that the product is subjected to from other products does not exceed the upper limit of the rated operating temperature for the product. 13. Note (1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2) You are requested not to use our product deviating from the reference specifications. (3) The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG CO., LTD Spec No.: JELF243C_0015V-01 P14/14 Appendix Electrical performance: Measuring method for inductance/Q (Q measurement is applicable only when the Q value is included in the rating table.) Perform measurement using the method described below. (Perform correction for the error deriving from the measuring terminal.) (1) Residual elements and stray elements of the measuring terminal can be expressed by the F parameter for the 2-pole terminal as shown in the figure below. (2) The product's impedance value (Zx) and measured impedance value (Zm) can be expressed as shown below, by using the respective current and voltage for input/output. Zm= V1 I1 Zx= V2 I2 (3) Thus, the relationship between the product's impedance value (Zx) and measured impedance value (Zm) is as follows. Zx=α Zm-β 1-ZmΓ Here, α = D/A = 1 β = B/D = Zsm - (1 - Yom Zsm) Zss Γ = C/A = Yom Zsm: measured impedance of short chip Zss: residual impedance of short chip (0.480 nH) Yom: measured admittance when measuring terminal is open (4) Calculate inductance Lx and Qx using the equations shown below. Im(Zx) Lx: inductance of chip coil Lx= 2πf Qx: Q of chip coil Im(Zx) Qx= f: measuring frequency Re(Zx) MURATA MFG CO., LTD