Spec No.: JELF243A_9114H-01
P1/15
CHIP COILS (CHIP INDUCTORS) LQW15AN□□□□0Z□
Murata Standard Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to chip coils (chip inductors) LQW15AN_0Z series for automotive electronics based on
AEC-Q200 except for power trains and safeties.
2. Part Numbering
(Ex.)
LQ
W
15
Product Structure Dimension
ID
(L × W)
A
N
1N5
B
0
Z
D
Application Category Inductance Tolerance Performance
Category
Packaging
and
Z: Automotive D: taping
characteristic
*B: bulk
*B: Bulk packing is also available (taping condition: however, products without reels are put in plastic bags).
3. Part Number and Rating
Operating temperature range
Storage temperature range
-55°C to +125°C
-55°C to +125°C
Inductance
Customer
Part number
DC
Self-resonant
resistance
frequency
(Ω max.)
(GHz min.)
Rated
current
(mA)
ESD
Rank
6: 25 kV
18.0
1000
6
0.03
18.0
1000
6
0.03
18.0
1000
6
10
0.07
17.0
750
6
10
0.07
17.0
750
6
C: ±0.2 nH
10
0.10
17.0
640
6
D: ±0.5 nH
10
0.10
17.0
640
6
1.8
C: ±0.2 nH
10
0.16
16.0
460
6
LQW15AN1N8D0ZD
1.8
D: ±0.5 nH
10
0.16
16.0
460
6
LQW15AN2N4B0ZD
2.4
B: ±0.1 nH
20
0.05
15.0
850
6
LQW15AN2N4C0ZD
2.4
C: ±0.2 nH
20
0.05
15.0
850
6
LQW15AN2N4D0ZD
2.4
D: ±0.5 nH
20
0.05
15.0
850
6
Murata
Part number
Nominal
value
(nH)
Tolerance
Q
(Min.)
LQW15AN1N5B0ZD
1.5
B: ±0.1 nH
10
0.03
LQW15AN1N5C0ZD
1.5
C: ±0.2 nH
10
LQW15AN1N5D0ZD
1.5
D: ±0.5 nH
10
LQW15AN1N6C0ZD
1.6
C: ±0.2 nH
LQW15AN1N6D0ZD
1.6
D: ±0.5 nH
LQW15AN1N7C0ZD
1.7
LQW15AN1N7D0ZD
1.7
LQW15AN1N8C0ZD
LQW15AN2N5B0ZD
2.5
B: ±0.1 nH
20
0.05
15.0
850
6
LQW15AN2N5C0ZD
2.5
C: ±0.2 nH
20
0.05
15.0
850
6
LQW15AN2N5D0ZD
2.5
D: ±0.5 nH
20
0.05
15.0
850
6
LQW15AN2N6B0ZD
2.6
B: ±0.1 nH
20
0.05
15.0
850
6
LQW15AN2N6C0ZD
2.6
C: ±0.2 nH
20
0.05
15.0
850
6
LQW15AN2N6D0ZD
2.6
D: ±0.5 nH
20
0.05
15.0
850
6
LQW15AN2N7B0ZD
2.7
B: ±0.1 nH
20
0.05
15.0
850
6
LQW15AN2N7C0ZD
2.7
C: ±0.2 nH
20
0.05
15.0
850
6
LQW15AN2N7D0ZD
2.7
D: ±0.5 nH
20
0.05
15.0
850
6
LQW15AN2N8B0ZD
2.8
B: ±0.1 nH
20
0.05
15.0
850
6
LQW15AN2N8C0ZD
2.8
C: ±0.2 nH
20
0.05
15.0
850
6
LQW15AN2N8D0ZD
2.8
D: ±0.5 nH
20
0.05
15.0
850
6
LQW15AN2N9B0ZD
2.9
B: ±0.1 nH
20
0.07
15.0
750
6
LQW15AN2N9C0ZD
2.9
C: ±0.2 nH
20
0.07
15.0
750
6
LQW15AN2N9D0ZD
2.9
D: ±0.5 nH
20
0.07
15.0
750
6
LQW15AN3N0B0ZD
3.0
B: ±0.1 nH
20
0.07
15.0
750
6
LQW15AN3N0C0ZD
3.0
C: ±0.2 nH
20
0.07
15.0
750
6
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P2/15
Inductance
Customer
Part number
DC
Self-resonant
resistance
frequency
(Ω max.)
(GHz min.)
Rated
current
(mA)
ESD
Rank
6: 25 kV
15.0
750
6
0.13
14.0
570
6
20
0.13
14.0
570
6
20
0.13
14.0
570
6
Murata
Part number
Nominal
value
(nH)
Tolerance
Q
(Min.)
LQW15AN3N0D0ZD
3.0
D: ±0.5 nH
20
0.07
LQW15AN3N1B0ZD
3.1
B: ±0.1 nH
20
LQW15AN3N1C0ZD
3.1
C: ±0.2 nH
LQW15AN3N1D0ZD
3.1
D: ±0.5 nH
LQW15AN3N2B0ZD
3.2
B: ±0.1 nH
15
0.17
14.0
500
6
LQW15AN3N2C0ZD
3.2
C: ±0.2 nH
15
0.17
14.0
500
6
LQW15AN3N2D0ZD
3.2
D: ±0.5 nH
15
0.17
14.0
500
6
LQW15AN3N9B0ZD
3.9
B: ±0.1 nH
25
0.07
10.0
750
6
LQW15AN3N9C0ZD
3.9
C: ±0.2 nH
25
0.07
10.0
750
6
LQW15AN3N9D0ZD
3.9
D: ±0.5 nH
25
0.07
10.0
750
6
LQW15AN4N1B0ZD
4.1
B: ±0.1 nH
25
0.07
10.0
750
6
LQW15AN4N1C0ZD
4.1
C: ±0.2 nH
25
0.07
10.0
750
6
LQW15AN4N1D0ZD
4.1
D: ±0.5 nH
25
0.07
10.0
750
6
LQW15AN4N3B0ZD
4.3
B: ±0.1 nH
25
0.07
10.0
750
6
LQW15AN4N3C0ZD
4.3
C: ±0.2 nH
25
0.07
10.0
750
6
LQW15AN4N3D0ZD
4.3
D: ±0.5 nH
25
0.07
10.0
750
6
LQW15AN4N4B0ZD
4.4
B: ±0.1 nH
25
0.07
8.0
750
6
LQW15AN4N4C0ZD
4.4
C: ±0.2 nH
25
0.07
8.0
750
6
LQW15AN4N4D0ZD
4.4
D: ±0.5 nH
25
0.07
8.0
750
6
LQW15AN4N5B0ZD
4.5
B: ±0.1 nH
25
0.07
8.0
750
6
LQW15AN4N5C0ZD
4.5
C: ±0.2 nH
25
0.07
8.0
750
6
LQW15AN4N5D0ZD
4.5
D: ±0.5 nH
25
0.07
8.0
750
6
LQW15AN4N6B0ZD
4.6
B: ±0.1 nH
25
0.07
8.0
750
6
LQW15AN4N6C0ZD
4.6
C: ±0.2 nH
25
0.07
8.0
750
6
LQW15AN4N6D0ZD
4.6
D: ±0.5 nH
25
0.07
8.0
750
6
LQW15AN4N7B0ZD
4.7
B: ±0.1 nH
25
0.07
8.0
750
6
LQW15AN4N7C0ZD
4.7
C: ±0.2 nH
25
0.07
8.0
750
6
LQW15AN4N7D0ZD
4.7
D: ±0.5 nH
25
0.07
8.0
750
6
LQW15AN4N8B0ZD
4.8
B: ±0.1 nH
25
0.07
8.0
750
6
LQW15AN4N8C0ZD
4.8
C: ±0.2 nH
25
0.07
8.0
750
6
LQW15AN4N8D0ZD
4.8
D: ±0.5 nH
25
0.07
8.0
750
6
LQW15AN4N9B0ZD
4.9
B: ±0.1 nH
25
0.12
8.0
600
6
LQW15AN4N9C0ZD
4.9
C: ±0.2 nH
25
0.12
8.0
600
6
LQW15AN4N9D0ZD
4.9
D: ±0.5 nH
25
0.12
8.0
600
6
LQW15AN5N0B0ZD
5.0
B: ±0.1 nH
25
0.12
8.0
600
6
LQW15AN5N0C0ZD
5.0
C: ±0.2 nH
25
0.12
8.0
600
6
LQW15AN5N0D0ZD
5.0
D: ±0.5 nH
25
0.12
8.0
600
6
LQW15AN5N1B0ZD
5.1
B: ±0.1 nH
25
0.12
8.0
600
6
LQW15AN5N1C0ZD
5.1
C: ±0.2 nH
25
0.12
8.0
600
6
LQW15AN5N1D0ZD
5.1
D: ±0.5 nH
25
0.12
8.0
600
6
LQW15AN5N8B0ZD
5.8
B: ±0.1 nH
25
0.09
8.0
700
6
LQW15AN5N8C0ZD
5.8
C: ±0.2 nH
25
0.09
8.0
700
6
LQW15AN5N8D0ZD
5.8
D: ±0.5 nH
25
0.09
8.0
700
6
LQW15AN6N2B0ZD
6.2
B: ±0.1 nH
25
0.09
8.0
700
6
LQW15AN6N2C0ZD
6.2
C: ±0.2 nH
25
0.09
8.0
700
6
LQW15AN6N2D0ZD
6.2
D: ±0.5 nH
25
0.09
8.0
700
6
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P3/15
Inductance
Customer
Part number
DC
Self-resonant
resistance
frequency
(Ω max.)
(GHz min.)
Rated
current
(mA)
ESD
Rank
6: 25 kV
6.0
700
6
0.09
6.0
700
6
25
0.09
6.0
700
6
25
0.09
6.0
700
6
25
0.09
6.0
700
6
25
0.09
6.0
700
6
Murata
Part number
Nominal
value
(nH)
Tolerance
Q
(Min.)
LQW15AN6N3B0ZD
6.3
B: ±0.1 nH
25
0.09
LQW15AN6N3C0ZD
6.3
C: ±0.2 nH
25
LQW15AN6N3D0ZD
6.3
D: ±0.5 nH
LQW15AN6N4B0ZD
6.4
B: ±0.1 nH
LQW15AN6N4C0ZD
6.4
C: ±0.2 nH
LQW15AN6N4D0ZD
6.4
D: ±0.5 nH
LQW15AN6N5B0ZD
6.5
B: ±0.1 nH
25
0.09
6.0
700
6
LQW15AN6N5C0ZD
6.5
C: ±0.2 nH
25
0.09
6.0
700
6
LQW15AN6N5D0ZD
6.5
D: ±0.5 nH
25
0.09
6.0
700
6
LQW15AN6N6B0ZD
6.6
B: ±0.1 nH
25
0.09
6.0
700
6
LQW15AN6N6C0ZD
6.6
C: ±0.2 nH
25
0.09
6.0
700
6
LQW15AN6N6D0ZD
6.6
D: ±0.5 nH
25
0.09
6.0
700
6
LQW15AN6N7B0ZD
6.7
B: ±0.1 nH
25
0.09
6.0
700
6
LQW15AN6N7C0ZD
6.7
C: ±0.2 nH
25
0.09
6.0
700
6
LQW15AN6N7D0ZD
6.7
D: ±0.5 nH
25
0.09
6.0
700
6
LQW15AN6N8G0ZD
6.8
G: ±2%
25
0.09
6.0
700
6
LQW15AN6N8H0ZD
6.8
H: ±3%
25
0.09
6.0
700
6
LQW15AN6N8J0ZD
6.8
J: ±5%
25
0.09
6.0
700
6
LQW15AN6N9G0ZD
6.9
G: ±2%
25
0.13
6.0
570
6
LQW15AN6N9H0ZD
6.9
H: ±3%
25
0.13
6.0
570
6
LQW15AN6N9J0ZD
6.9
J: ±5%
25
0.13
6.0
570
6
LQW15AN7N0G0ZD
7.0
G: ±2%
25
0.13
6.0
570
6
LQW15AN7N0H0ZD
7.0
H: ±3%
25
0.13
6.0
570
6
LQW15AN7N0J0ZD
7.0
J: ±5%
25
0.13
6.0
570
6
LQW15AN7N1G0ZD
7.1
G: ±2%
25
0.13
6.0
570
6
LQW15AN7N1H0ZD
7.1
H: ±3%
25
0.13
6.0
570
6
LQW15AN7N1J0ZD
7.1
J: ±5%
25
0.13
6.0
570
6
LQW15AN7N2G0ZD
7.2
G: ±2%
25
0.13
6.0
570
6
LQW15AN7N2H0ZD
7.2
H: ±3%
25
0.13
6.0
570
6
LQW15AN7N2J0ZD
7.2
J: ±5%
25
0.13
6.0
570
6
LQW15AN7N3G0ZD
7.3
G: ±2%
25
0.13
6.0
570
6
LQW15AN7N3H0ZD
7.3
H: ±3%
25
0.13
6.0
570
6
LQW15AN7N3J0ZD
7.3
J: ±5%
25
0.13
6.0
570
6
LQW15AN7N5G0ZD
7.5
G: ±2%
25
0.13
6.0
570
6
LQW15AN7N5H0ZD
7.5
H: ±3%
25
0.13
6.0
570
6
LQW15AN7N5J0ZD
7.5
J: ±5%
25
0.13
6.0
570
6
LQW15AN8N2G0ZD
8.2
G: ±2%
25
0.14
5.5
540
6
LQW15AN8N2H0ZD
8.2
H: ±3%
25
0.14
5.5
540
6
LQW15AN8N2J0ZD
8.2
J: ±5%
25
0.14
5.5
540
6
LQW15AN8N6G0ZD
8.6
G: ±2%
25
0.14
5.5
540
6
LQW15AN8N6H0ZD
8.6
H: ±3%
25
0.14
5.5
540
6
LQW15AN8N6J0ZD
8.6
J: ±5%
25
0.14
5.5
540
6
LQW15AN8N7G0ZD
8.7
G: ±2%
25
0.14
5.5
540
6
LQW15AN8N7H0ZD
8.7
H: ±3%
25
0.14
5.5
540
6
LQW15AN8N7J0ZD
8.7
J: ±5%
25
0.14
5.5
540
6
LQW15AN8N8G0ZD
8.8
G: ±2%
25
0.14
5.5
540
6
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P4/15
Inductance
Customer
Part number
DC
Self-resonant
resistance
frequency
(Ω max.)
(GHz min.)
Rated
current
(mA)
ESD
Rank
6: 25 kV
5.5
540
6
5.5
540
6
Murata
Part number
Nominal
value
(nH)
Tolerance
Q
(Min.)
LQW15AN8N8H0ZD
8.8
H: ±3%
25
0.14
LQW15AN8N8J0ZD
8.8
J: ±5%
25
0.14
LQW15AN8N9G0ZD
8.9
G: ±2%
25
0.14
5.5
540
6
LQW15AN8N9H0ZD
8.9
H: ±3%
25
0.14
5.5
540
6
LQW15AN8N9J0ZD
8.9
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N0G0ZD
9.0
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N0H0ZD
9.0
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N0J0ZD
9.0
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N1G0ZD
9.1
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N1H0ZD
9.1
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N1J0ZD
9.1
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N2G0ZD
9.2
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N2H0ZD
9.2
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N2J0ZD
9.2
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N3G0ZD
9.3
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N3H0ZD
9.3
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N3J0ZD
9.3
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N4G0ZD
9.4
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N4H0ZD
9.4
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N4J0ZD
9.4
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N5G0ZD
9.5
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N5H0ZD
9.5
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N5J0ZD
9.5
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N6G0ZD
9.6
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N6H0ZD
9.6
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N6J0ZD
9.6
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N7G0ZD
9.7
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N7H0ZD
9.7
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N7J0ZD
9.7
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N8G0ZD
9.8
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N8H0ZD
9.8
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N8J0ZD
9.8
J: ±5%
25
0.14
5.5
540
6
LQW15AN9N9G0ZD
9.9
G: ±2%
25
0.14
5.5
540
6
LQW15AN9N9H0ZD
9.9
H: ±3%
25
0.14
5.5
540
6
LQW15AN9N9J0ZD
9.9
J: ±5%
25
0.14
5.5
540
6
LQW15AN10NG0ZD
10
G: ±2%
25
0.17
5.5
500
6
LQW15AN10NH0ZD
10
H: ±3%
25
0.17
5.5
500
6
LQW15AN10NJ0ZD
10
J: ±5%
25
0.17
5.5
500
6
LQW15AN11NG0ZD
11
G: ±2%
30
0.14
5.5
500
6
LQW15AN11NH0ZD
11
H: ±3%
30
0.14
5.5
500
6
LQW15AN11NJ0ZD
11
J: ±5%
30
0.14
5.5
500
6
LQW15AN12NG0ZD
12
G: ±2%
30
0.14
5.5
500
6
LQW15AN12NH0ZD
12
H: ±3%
30
0.14
5.5
500
6
LQW15AN12NJ0ZD
12
J: ±5%
30
0.14
5.5
500
6
LQW15AN13NG0ZD
13
G: ±2%
25
0.21
5.0
430
6
LQW15AN13NH0ZD
13
H: ±3%
25
0.21
5.0
430
6
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P5/15
Inductance
Customer
Part number
DC
Self-resonant
resistance
frequency
(Ω max.)
(GHz min.)
Rated
current
(mA)
ESD
Rank
6: 25 kV
5.0
430
6
5.0
460
6
Murata
Part number
Nominal
value
(nH)
Tolerance
Q
(Min.)
LQW15AN13NJ0ZD
13
J: ±5%
25
0.21
LQW15AN15NG0ZD
15
G: ±2%
30
0.16
LQW15AN15NH0ZD
15
H: ±3%
30
0.16
5.0
460
6
LQW15AN15NJ0ZD
15
J: ±5%
30
0.16
5.0
460
6
LQW15AN16NG0ZD
16
G: ±2%
25
0.24
4.5
370
6
LQW15AN16NH0ZD
16
H: ±3%
25
0.24
4.5
370
6
LQW15AN16NJ0ZD
16
J: ±5%
25
0.24
4.5
370
6
LQW15AN18NG0ZD
18
G: ±2%
25
0.27
4.5
370
6
LQW15AN18NH0ZD
18
H: ±3%
25
0.27
4.5
370
6
LQW15AN18NJ0ZD
18
J: ±5%
25
0.27
4.5
370
6
LQW15AN19NG0ZD
19
G: ±2%
25
0.27
4.5
370
6
LQW15AN19NH0ZD
19
H: ±3%
25
0.27
4.5
370
6
LQW15AN19NJ0ZD
19
J: ±5%
25
0.27
4.5
370
6
LQW15AN20NG0ZD
20
G: ±2%
25
0.27
4.0
370
6
LQW15AN20NH0ZD
20
H: ±3%
25
0.27
4.0
370
6
LQW15AN20NJ0ZD
20
J: ±5%
25
0.27
4.0
370
6
LQW15AN22NG0ZD
22
G: ±2%
25
0.30
4.0
310
6
LQW15AN22NH0ZD
22
H: ±3%
25
0.30
4.0
310
6
LQW15AN22NJ0ZD
22
J: ±5%
25
0.30
4.0
310
6
LQW15AN23NG0ZD
23
G: ±2%
25
0.30
3.8
310
6
LQW15AN23NH0ZD
23
H: ±3%
25
0.30
3.8
310
6
LQW15AN23NJ0ZD
23
J: ±5%
25
0.30
3.8
310
6
LQW15AN24NG0ZD
24
G: ±2%
25
0.52
3.5
280
6
LQW15AN24NH0ZD
24
H: ±3%
25
0.52
3.5
280
6
LQW15AN24NJ0ZD
24
J: ±5%
25
0.52
3.5
280
6
LQW15AN27NG0ZD
27
G: ±2%
25
0.52
3.5
280
6
LQW15AN27NH0ZD
27
H: ±3%
25
0.52
3.5
280
6
LQW15AN27NJ0ZD
27
J: ±5%
25
0.52
3.5
280
6
LQW15AN30NG0ZD
30
G: ±2%
25
0.58
3.3
270
6
LQW15AN30NH0ZD
30
H: ±3%
25
0.58
3.3
270
6
LQW15AN30NJ0ZD
30
J: ±5%
25
0.58
3.3
270
6
LQW15AN33NG0ZD
33
G: ±2%
25
0.63
3.2
260
6
LQW15AN33NH0ZD
33
H: ±3%
25
0.63
3.2
260
6
LQW15AN33NJ0ZD
33
J: ±5%
25
0.63
3.2
260
6
LQW15AN36NG0ZD
36
G: ±2%
25
0.63
3.1
260
6
LQW15AN36NH0ZD
36
H: ±3%
25
0.63
3.1
260
6
LQW15AN36NJ0ZD
36
J: ±5%
25
0.63
3.1
260
6
LQW15AN39NG0ZD
39
G: ±2%
25
0.70
3.0
250
6
LQW15AN39NH0ZD
39
H: ±3%
25
0.70
3.0
250
6
LQW15AN39NJ0ZD
39
J: ±5%
25
0.70
3.0
250
6
LQW15AN40NG0ZD
40
G: ±2%
25
0.70
3.0
250
6
LQW15AN40NH0ZD
40
H: ±3%
25
0.70
3.0
250
6
LQW15AN40NJ0ZD
40
J: ±5%
25
0.70
3.0
250
6
LQW15AN43NG0ZD
43
G: ±2%
25
0.70
3.0
250
6
LQW15AN43NH0ZD
43
H: ±3%
25
0.70
3.0
250
6
LQW15AN43NJ0ZD
43
J: ±5%
25
0.70
3.0
250
6
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P6/15
Inductance
Customer
Part number
DC
Self-resonant
resistance
frequency
(Ω max.)
(GHz min.)
Rated
current
(mA)
ESD
Rank
6: 25 kV
2.9
210
6
2.9
210
6
1.08
2.9
210
6
1.08
2.85
210
6
Murata
Part number
Nominal
value
(nH)
Tolerance
Q
(Min.)
LQW15AN47NG0ZD
47
G: ±2%
25
1.08
LQW15AN47NH0ZD
47
H: ±3%
25
1.08
LQW15AN47NJ0ZD
47
J: ±5%
25
LQW15AN51NG0ZD
51
G: ±2%
25
LQW15AN51NH0ZD
51
H: ±3%
25
1.08
2.85
210
6
LQW15AN51NJ0ZD
51
J: ±5%
25
1.08
2.85
210
6
LQW15AN56NG0ZD
56
G: ±2%
25
1.17
2.8
200
6
LQW15AN56NH0ZD
56
H: ±3%
25
1.17
2.8
200
6
LQW15AN56NJ0ZD
56
J: ±5%
25
1.17
2.8
200
6
LQW15AN62NG0ZD
62
G: ±2%
20
1.82
2.6
145
6
LQW15AN62NH0ZD
62
H: ±3%
20
1.82
2.6
145
6
LQW15AN62NJ0ZD
62
J: ±5%
20
1.82
2.6
145
6
LQW15AN68NG0ZD
68
G: ±2%
20
1.96
2.5
140
6
LQW15AN68NJ0ZD
68
J: ±5%
20
1.96
2.5
140
6
LQW15AN72NG0ZD
72
G: ±2%
20
2.10
2.5
135
6
LQW15AN72NJ0ZD
72
J: ±5%
20
2.10
2.5
135
6
LQW15AN75NG0ZD
75
G: ±2%
20
2.10
2.4
135
6
LQW15AN75NJ0ZD
75
J: ±5%
20
2.10
2.4
135
6
LQW15AN82NG0ZD
82
G: ±2%
20
2.24
2.3
130
6
LQW15AN82NJ0ZD
82
J: ±5%
20
2.24
2.3
130
6
LQW15AN91NG0ZD
91
G: ±2%
20
2.38
2.1
125
6
LQW15AN91NJ0ZD
91
J: ±5%
20
2.38
2.1
125
6
LQW15ANR10J0ZD
100
J: ±5%
20
2.52
1.5
120
6
LQW15ANR12J0ZD
120
J: ±5%
20
2.66
1.0
110
6
4. Testing Conditions
Unless otherwise specified
Temperature: ordinary temperature (15°C to 35°C)
Humidity: ordinary humidity [25% to 85% (RH)]
In case of doubt
Temperature: 20°C±2°C
Humidity: 60% to 70% (RH)
Atmospheric pressure: 86 kPa to 106 kPa
5. Appearance and Dimensions
Unit mass (typical value): 0.0008 g
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P7/15
6. Marking
No marking.
7. Electrical Performance
No.
Item
7.1
Inductance
Specification
Meet chapter 3 ratings.
Test method
Measuring equipment: Keysight E4991A or the
equivalent
Measuring frequency:
Inductance
100 MHz
Q
250 MHz 1.5 nH to 43 nH
200 MHz 47 nH to 68 nH
7.2
Q
150 MHz 72 nH to 120 nH
Measuring conditions:
Measurement signal level: Approx. 0 dBm
Measurement terminal distance: 0.5 mm
Electrical length: 10.0 mm
Measuring fixture: Keysight 16197A
Position the chip coil under test as shown in the
measuring example below and connect it to the
electrode by applying weight.
Measurement example:
Meet chapter 3 ratings.
Measuring method: see "Electrical performance:
Measuring method for inductance/Q" in the chapter
"15. Appendix".
7.3
DC resistance
Meet chapter 3 ratings.
Measuring equipment: digital multimeter
7.4
Self-resonant
frequency
Meet chapter 3 ratings.
Measuring equipment: Keysight N5230A or the
equivalent
7.5
Rated current
Product temperature rise: 20°C max.
Apply the rated current specified in chapter 3.
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P8/15
8. AEC-Q200 Requirement
8.1 Performance [based on table 5 for magnetics (inductors/transformer) AEC-Q200 Rev. D issued June 1,
2010]
AEC-Q200
No.
3
Stress
High
temperature
exposure
Murata specification/deviation
Test method
1000 h at 125°C
Set for 24 h at room condition, then
measured.
Meet table A after testing.
Table A
Appearance
No damage
Inductance change rate (at 100 MHz)
4
Temperature
cycling
1000 cycles
-40°C to +125°C
Set for 24 h at room condition, then
measured.
7
Biased humidity 1000 h at 85°C, 85% (RH). Unpowered.
Set for 24 h at room condition, then
measured.
Meet table A after testing.
8
Operational life
Meet table A after testing.
Apply 125°C 1000 h
Set for 24 h at room condition, then
measured.
Within ±5%
Meet table A after testing.
9
External visual
Visual inspection
No abnormalities
10
Physical
dimension
Meet chapter 5, "Appearance and
Dimensions".
No defects
12
Resistance to
solvents
Per MIL-STD-202
Method 215
Not applicable
13
Mechanical
shock
Per MIL-STD-202
Meet table A after testing.
Method 213
Condition C:
100 g’s (0.98 N), 6 ms, half sine, 12.3 ft/s
14
Vibration
5 g's (0.049 N) for 20 min, 12 cycles each Meet table A after testing.
of 3 orientations
Test from 10 Hz to 2000 Hz
15
Resistance to
soldering heat
No-heating
Solder temperature
260°C±5°C
Immersion time 10 s
Pre-heating: 150°C±10°C, 60 s to 90 s
Meet table A after testing.
17
ESD
Per AEC-Q200-002
ESD rank: Refer to chapter 3 ratings.
Meet table A after testing.
18
Solderbility
Per J-STD-002
Method b: not applicable
95% of the terminations is to be soldered (except exposed
wire).
19
Electrical
Measured: inductance
characterization
No defects
20
Flammability
Per UL-94
Not applicable
21
Board flex
Epoxy-PCB (1.6 mm)
Deflection 2 mm (min.)
Holding time 60 s
Meet table B after testing.
Table B
Appearance
DC resistance change rate
22
Terminal
strength
Per AEC-Q200-006
A force of 17.7 N for 60 s
No damage
Within ±10%
No defects
Murata deviation request: 5 N for 60 s
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P9/15
9. Specification of Packaging
9.1 Appearance and dimensions of tape (8 mm width/paper tape)
(in mm)
A* (mm)
B* (mm)
(Dimensional
tolerance ±0.03)
(Dimensional
tolerance ±0.03)
1N5, 2N4 to 2N8, 3N9 to 4N8, 5N8 to 6N8, 8N2 to 9N9, 11N, 12N, 15N
0.69
1.18
1N6 to 1N8, 2N9, 3N0, 3N1, 3N2, 4N9 to 5N1, 6N9 to 7N5, 10N, 13N, 16N to 23N,
R10, R12
0.66
1.18
0.64
1.18
Inductance
24N to 91N
*Typical value
9.2 Taping specifications
Packing quantity
(Standard quantity)
10000 pcs/reel
Packing method
The products are placed in embossed cavities of a base tape and sealed by a cover tape.
Feed hole position
The feed holes on the base tape are on the right side when the cover tape is pulled toward the user.
Joint
The base tape and the cover tape are seamless.
Number of missing
products
Number of missing products within 0.025% of the number per reel or 1 pc., whichever is greater, and
are not continuous. The specified quantity per reel is kept.
9.3 Break down force of tape
Break down force of cover tape
5 N min.
9.4 Peeling off force of cover tape
Speed of peeling off
Peeling off force
165°to 180゜
300 mm/min
0.1 N to 0.6 N (The lower limit is for typical value.)
F
Cover tape
Base tape
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P10/15
9.5 Dimensions of leader section, trailer section and reel
A vacant section is provided in the leader (start) section and trailer (end) section of the tape for the product. The leader
section is further provided with an area consisting only of the cover tape (or top tape). (See the diagram below.)
9.6 Marking for reel
Customer part number, Murata part number, inspection number (*1), RoHS marking (*2), quantity, etc.
*1 Expression of inspection No.: (1) Factory code
□□
○○○○
(2) Date
First digit: year/last digit of year
(1)
(2)
(3)
Second digit: month/Jan. to Sep.→1 to 9, Oct. to Dec.→O, N, D
Third, Fourth digit: day
(3) Serial No.
*2 Expression of RoHS marking: (1) RoHS regulation conformity
ROHSY
()
(2) Murata classification number
(1)
(2)
9.7 Marking on outer box (corrugated box)
Customer name, purchasing order number, customer part number, Murata part number, RoHS marking (*2), quantity, etc.
9.8 Specification of outer box
Label
H
D
W
Dimensions of outer box
(mm)
W
D
H
186
186
93
Standard reel quantity
in outer box (reel)
5
* Above outer box size is typical. It depends on a
quantity of an order.
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
10.
P11/15
Caution
10.1 Restricted applications
Please contact us before using our products for the applications listed below which require especially high reliability for the
prevention of defects which might directly cause damage to the third party's life, body or property.
(1) Aircraft equipment
(6) Disaster/crime prevention equipment
(2) Aerospace equipment
(7) Traffic signal equipment
(3) Undersea equipment
(8) Transportation equipment (trains, ships, etc.)
(4) Power plant control equipment
(9) Data-processing equipment
(5) Medical equipment
(10) Applications of similar complexity and/or reliability requirements
to the applications listed in the above
10.2 Precautions on rating
Do not use the products in excess of their rated current. Doing so may cause the product to generate heat, resulting in short
circuit between wires, wire breakage, or melted solder, which may cause dropping of parts.
10.3 Fail-safe
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the
abnormal function or the failure of our product.
10.4 Corrosive gas
Please refrain from use since contact with environments with corrosive gases (sulfur gas [hydrogen sulfide, sulfur dioxide,
etc.], chlorine, ammonia, etc.) or oils (cutting oil, silicone oil, etc.) that have come into contact with the previously stated
corrosive gas environment will result in deterioration of product quality or an open from deterioration due to corrosion of
product electrode, etc. We will not bear any responsibility for use under these environments.
11. Precautions for Use
This product is for use only with reflow soldering. It is designed to be mounted by soldering. If you want to use other
mounting method, for example, using a conductive adhesive, please consult us beforehand.
Also, if repeatedly subjected to temperature cycles or other thermal stress, due to the difference in the coefficient of thermal
expansion with the mounting substrate, the solder (solder fillet part) in the mounting part may crack.
The occurrence of cracks due to thermal stress is affected by the size of the land where mounted, the solder volume, and
the heat dissipation of the mounting substrate. Carefully design it when a large change in ambient temperature is assumed.
11.1 Land dimensions
The following diagram shows the recommended land dimensions for reflow soldering.
The land dimensions are designed in consideration of electrical characteristics and mountability. Use of other land
dimensions may preclude achievement of performance. In some cases, it may result in poor solderability, including positional
shift. If you use other land pattern, consider it adequately.
a
0.50
b
1.2
c
0.65
(in mm)
11.2 Flux and solder used
Flux
• Use a rosin-based flux that includes an activator with a chlorine conversion value of 0.06(wt)% to 0.1(wt)%.
• Do not use a highly acidic flux with a halide content exceeding 0.2(wt)% (chlorine conversion value).
• Do not use a water-soluble flux.
Solder
• Use Sn-3.0Ag-0.5Cu solder.
• Standard thickness of solder paste: 100 μm to 150 μm
If you want to use a flux other than the above, please consult our technical department.
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P12/15
11.3 Soldering conditions (reflow)
• Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to
150°C max.
Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max.
Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality.
• Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and/or resulting in the deterioration of product
quality.
Temp.
(℃)
260℃
245℃±3℃
220℃
230℃
Limit Profile
180
150
Standard Profile
30s～60s
60s max.
90s±30s
Time. (s)
Standard profile
Limit profile
Pre-heating
150°C to 180°C/90 s±30 s
150°C to 180°C/90 s±30 s
Heating
Above 220°C/30 s to 60 s
Above 230°C/60 s max.
245°C±3°C
260°C/10 s
2 times
2 times
Peak temperature
Number of reflow cycles
11.4 Reworking with soldering iron
The following requirements must be met to rework a soldered product using a soldering iron.
Item
Requirement
Pre-heating
150°C/approx. 1 min
Tip temperature of soldering iron
350°C max.
Power consumption of soldering iron
80 W max.
Tip diameter of soldering iron
Soldering time
Number of reworking operations
ø3 mm max.
3 s (+1 s, -0 s)
2 times max.
* Avoid a direct contact of the tip of the soldering iron with the product. Such a
direction contact may cause cracks in the ceramic body due to thermal shock.
11.5 Solder volume
Solder shall be used not to increase the volume too much.
An increased solder volume increases mechanical stress on the product. Exceeding solder volume may cause the failure of
mechanical or electrical performance.
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P13/15
11.6 Product's location
The following shall be considered when designing and laying out PCBs.
(1) PCB shall be designed so that products are not subject to mechanical stress due to warping the board.
[Products direction]
Products shall be located in the sideways direction (length: a < b) to the mechanical stress.
a
b
〈 Poor example〉
〈 Good example〉
(2) Components location on PCB separation
It is effective to implement the following measures, to reduce stress in separating the board.
It is best to implement all of the following three measures; however, implement as many measures as possible to reduce
stress.
Contents of measures
Stress level
(1) Turn the mounting direction of the component parallel to the
board separation surface.
A > D*1
(2) Add slits in the board separation part.
A>B
(3) Keep the mounting position of the component away from the
board separation surface.
A>C
*1 A > D is valid when stress is added vertically to the perforation as with hand separation.
If a cutting disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
(3) Mounting components near screw holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the
tightening of the screw.
Mount the component in a position as far away from the screw holes as possible.
11.7 Handling of substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate
when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P14/15
11.8 Cleaning
The product shall be cleaned under the following conditions.
(1) The cleaning temperature shall be 60°C max. If isopropyl alcohol (IPA) is used, the cleaning temperature shall be 40°C
max.
(2) Perform ultrasonic cleaning under the following conditions. Exercise caution to prevent resonance phenomenon in
mounted products and the PCB.
Item
Requirement
Power
Time
20 W/L max.
5 min max.
Frequency
28 kHz to 40 kHz
(3) Cleaner
Alcohol-based cleaner: IPA
Aqueous agent: PINE ALPHA ST-100S
(4) There shall be no residual flux or residual cleaner. When using aqueous agent, rinse the product with deionized water
adequately and completely dry it so that no cleaner is left.
* For other cleaning, consult our technical department.
11.9 Storage and transportation
Storage period
Use the product within 12 months after delivery.
If you do not use the product for more than 12 months, check solderability before using it.
Storage conditions
• The products shall be stored in a room not subject to rapid changes in temperature and humidity.
The recommended temperature range is -10°C to +40°C. The recommended relative humidity
range is 15% to 85%.
Keeping the product in corrosive gases, such as sulfur, chlorine gas or acid, oxidizes the
electrode, resulting in poor solderability or corrosion of the coil wire of the product.
• Do not keep products in bulk packaging. Doing so may cause collision between the products or
between the products and other products, resulting in core chipping or wire breakage.
• Do not place the products directly on the floor; they should be placed on a palette so that they are
not affected by humidity or dust.
• Avoid keeping the products in a place exposed to direct sunlight, heat or vibration.
Transportation
Excessive vibration and impact reduces the reliability of the products. Exercise caution when
handling the products.
11.10 Resin coating
The inductance value may change due to high cure-stress of resin to be used for coating/molding products.
A wire breakage issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating
condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some
operating condition may cause corrosion of wire of coil, leading to wire breakage.
So, please pay your careful attention when you select resin in case of coating/molding the products with the resin.
Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products mounted on your
board.
11.11 Handling of product
• Sharp material such as a pair of tweezers or other material such as bristles of cleaning brush, shall not be touched to the
winding portion to prevent the breaking of wire.
• Mechanical shock should not be applied to the products mounted on the board to prevent the breaking of the core.
11.12 Handling with mounting equipment
• With some types of mounting equipment, a support pin pushes up the product from the bottom of the base (paper) tape
when the product is sucked with the pick-up nozzle.
When using this type of equipment, detach the support pin to prevent the breaking of wire on the product.
• In some cases, the laser recognition function of the mounting equipment may not recognize this product correctly.
Please contact us when using laser recognition. (There is no problem with the permeation and reflection type.)
12.
Note
(1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to
your product.
(2) You are requested not to use our product deviating from the reference specifications.
(3) The contents of this reference specification are subject to change without advance notice. Please approve our product
specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG CO., LTD
Spec No.: JELF243A_9114H-01
P15/15
13. Appendix
Electrical performance: Measuring method for inductance/Q (Q measurement is applicable only when the Q value is
included in the rating table.)
Perform measurement using the method described below. (Perform correction for the error deriving from the measuring
terminal.)
(1) Residual elements and stray elements of the measuring terminal can be expressed by the F parameter for the 2-pole
terminal as shown in the figure below.
(2) The product's impedance value (Zx) and measured impedance value (Zm) can be expressed as shown below, by using
the respective current and voltage for input/output.
Zm=
V1
I1
Zx=
V2
I2
(3) Thus, the relationship between the product's impedance value (Zx) and measured impedance value (Zm) is as follows.
Zx=α
Zm-β
1-ZmΓ
Here,
α = D/A = 1
β = B/D = Zsm - (1 - Yom Zsm) Zss
Γ = C/A = Yom
Zsm: measured impedance of short chip
Zss: residual impedance of short chip (0.556 nH)
Yom: measured admittance when measuring terminal is open
(4) Calculate inductance Lx and Qx using the equations shown below.
Im (Zx)
Lx: inductance of chip coil
Lx=
2πf
Qx: Q of chip coil
Im (Zx)
Qx=
f: measuring frequency
Re (Zx)
MURATA MFG CO., LTD
工商网监
湘ICP备2023018690号
