MM126320

Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0062D Part Number : MM126320 Written by Checked by Date Y. Mori T. Kuriyama 30/Jul./2012 Dia. 6.7 +/-0.1 SMA-Female 12 +/-0.15 16 +/-0.15 Dia. 2.5 +/-0.1 SPECIFICATION Revised A:24/Apr./2012 MR, B:30/Jul./2012 MR, C:4/Sep./2014 YM, D:21/Oct./2015 IG 1. MECHANICAL C> Automatic measurement probe for SWD, SWF and SWG. MM126317 and MM126312 are used as calibration adapter. SWD/SWF/SWG 9.7 +/-0.1 5 +/-0.15 12.65 +/-0.2 20.2 +/-0.2 (32.85) 9 +/-0.2 Figure.1 Construction 2. SCALE:FREE TOLERANCES UNLESS OTHRWISE SPECIFIED: +/-0.5 UNIT:mm RATING: Item Specification 30Vr.m.s. maximum DC to 6GHz 50 -40C to +85C 500 M minimum No evidence of breakdown in AC 300V r.m.s, 1 minute Center contact 25.0mmax. Center contact 70.0mmax. (SWG only) Outer contact 20.0mmax. 1.6max (DC~3GHz) 1.7max (3~6GHz) 2.1max (6~11GHz) (SWG only) 0.5dB max (DC~3GHz) 0.85dB max (3~6GHz) 1.4dB max (6~11GHz) (SWG only) 1M cycles Voltage Rating Nominal Frequency Range Nominal Impedance Temperature Rating Insulation Resistance Withstanding Voltage A> Initial Contact Resistance (without conductor resistance) Voltage Standing Wave Ratio (V.S.W.R.) Insertion Loss B> Durability 1/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0062D Part Number : MM126320 Written by Checked by Date Y. Mori T. Kuriyama 30/Jul./2012 3. USE THIS PRODUCTS 3.1 The directions for attachment to measurement machine. The probe must be attached to machine at the two screw holes in probe flange. (Figure 2) SCREW HOLE Figure.2 Screw hole position 3.2 The tolerance of position against SWD, SWF and SWG. 3.2.1 Probe has the centering function by itself, +/-0.5mm is permitted against the hole center of SWD, SWF and SWG. Please keep avoid needless force to SMA connector for come back the center position, when disengagement of probe. (Figure 3) There is the possibility, following function +/-0.5mm is not permitted against the hole center of SWD, SWF and SWG, when probe effect the needless force. 3.2.2 To get the 15dB or higher isolation (up to 6GHz), the proper engagement strokes from the top surface of Fixture STAGE to the top surface of PWB is 18.2 to 20.0mm (SWD/SWF/SWG) D> 18.2 to 20.0 JIG 0 +/-0.5 (Gap of Vertical Axis) Before Engagement Receptacle Bottom Surface of Receptacle Touch the Receptacle Finish to Engagement UNIT: mm Figure.3 Acceptable Engagement range 2/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0062D Part Number : MM126320 Written by Checked by Date Y. Mori T. Kuriyama 30/Jul./2012 3.3 The machine’s hole diameter for attachment probe. To accept +/-0.5mm against the hole center of SWD, SWF and SWG. Please design the machine by Figure 4. Dia. 9mm Min. UNIT: mm Figure.4 Machine’s hole diameter for attachment probe 3.4 The slant angle tolerance of probe against SWD, SWF and SWG. (Figure 5) To have the stable measurement, MM126320 slant angle must be +/-2degree. Figure.5 Probe Shape Operation Manual for Auto Measurement probe (MM126320) 3/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0062D Part Number : MM126320 4. Written by Checked by Date Y. Mori T. Kuriyama 30/Jul./2012 ! CAUTION Limitation of Applications Please do not use our products for the applications listed below which require specially high reliability for the prevention of defects which may directly or indirectly cause damage to the third party's life, body or property. (1) Aircraft equipment (2) Aerospace equipment (3) Undersea equipment (4) Power plant control equipment (5) Medical equipment (6) Transportation equipment (vehicles, trains, ships, etc.) (7) Traffic signal equipment (8) Disaster prevention / crime prevention equipment (9) Data-processing equipment (10) Application of similar complexity and/or reliability requirements to the applications listed in the above. 4/4