MM206417

Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0122A Part Number : MM206417 Written by I.Gan Checked by T.Kuriyama Date 26/Aug./2015 Revised A: 8/Mar. /’16 YM SPECIFICATION 1. MECHANICAL Automatic measurement probe for SWG. MM126317 and MM126312 are used as calibration adapters. 0. 53 R 10+/-0.1 .1 .05 +0 .0 2-D 5/-0 .0 ia 2.2 1 +/0 .1 6+/-0.04 Dia 0.20 3.0 Dia.3.0 SMPM-Male Dia.2.5+/-0.1 1.05+0.05/-0.01 1.50 4.11 0.7+/-0.2 Di a. 14 .4 SWG type 4+/-0.1 20+/-0.3 Scale: Free Tolerance Unless Otherwise Specified: +/- 0.2 Unit: mm Figure 1. Construction 2. RATING: Item Voltage Rating Nominal Frequency Range Nominal Impedance Temperature Rating Insulation Resistance Withstanding Voltage Initial Contact Resistance (without conductor resistance) A> Voltage Standing Wave Ratio (V.S.W.R.) Specification 30Vr.m.s. maximum DC to 11GHz 50Ω -40°C to +85°C 500 MΩ minimum No evidence of breakdown Center contact 70.0mΩmax. Outer contact 20.0mΩmax. Meet the requirements of following spec. 1.4max (DC to 3GHz) 1.5max (3GHz to 6GHz) 2.3max (6GHz to 11GHz) 0.4 dB Max (DC to 3GHz) 0.6 dB Max (3GHz to 6GHz) 1.8 dB Max (6GHz to 11GHz) 250K cycles A> Insertion Ioss Durability 1/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0122A Part Number : MM206417 Written by I.Gan Checked by T.Kuriyama Date 26/Aug./2015 3. USE THIS PRODUCT 3.1 Attach to measurement machine MM206417 must be attached to machine at the two screw holes in probe flange (Figure 2). Using guide pins is recommended. The guide pins should not be above probe flange (Figure 3). SCREW HOLE Figure 2. Screw hole Guide pin should not be above probe flange Guide pin Figure 3. Positional relation between guide pin and probe flange 2/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0122A Part Number : MM206417 Written by I.Gan Checked by T.Kuriyama Date 26/Aug./2015 3.2 The tolerance of position against SWG type receptacle 3.2.1 MM206417 has a centering function by its design, +/-0.5mm is permitted against the hole center of SWG type receptacle. Please avoid needless force to SMPM interface when MM206417 is disengaged from SWG type receptacle and comes back to its original position. To avoid the needless force, please use extension cable assembly, MXHQ87SM3000/MXHR87SN3000 (Figure 4/Figure 5). Centering function +/-0.5mm may not be permitted against the hole center of SWG type receptacle, when MM206417 is affected by the needless force. Please hold the cable to keep some margin like this Cable holding point Over 30mm O MXHQ87SM3000 ve rR 20 m m Over 50mm MM206417 To Measurement Equipment Figure 4. Instruction of MXHQ87SM3000 To Measurement Equipment MXHR87SN3000 MM206417 Figure 5. Instruction of MXHR87SN3000 Please use M19500 for un-mating MM206417 with MXHQ87SM3000/MXHR87SN3000 (Figure 6). Figure 6. SMPM interface un-mating jig: M19500 3/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PV0122A Part Number : MM206417 Written by I.Gan Checked by T.Kuriyama Date 26/Aug./2015 19.07 to 20.07 18.5 to 19.5 (Using Area) 20 3.2.2 To get 10dB or higher isolation (up to 11GHz), the engagement strokes from the flange to the tip of probe is 18.5mm to 19.5mm (Figure 7). 0+/-0.5 Unmating Mating Unit:mm Figure 7. Acceptable Engagement range to SWG type receptacle 3.3 The slant angle tolerance of probe against SWG type Receptacle (Figure 8) To have a stable measurement, slant angle of MM206417 must be within +/-2degree. Figure 8. Probe Shape Operation Manual for Auto Measurement probe (MM206417) 4/4