MM206621

Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PU0076A Part Number : MM206621 Written by T.Yamamoto Checked by T.Kuriyama Date 22/Jun./2016 SPECIFICATION Revised A: 26/Sep./’16 KT 1. MECHANICAL Automatic measurement probe for SWH. MM126511 and MM126512 are used as calibration adapters. 1.05+0.05/-0.01 0.8+/-0.2 20+/-0.3 4.11 1.25+/-0.05 1.50 Dia .14 .4 SWH Scale: Free Tolerance Unless Otherwise Specified: +/- 0.2 Unit: mm Figure 1. Construction 2. RATING: Item Specification 30Vr.m.s. maximum DC to 6GHz 50 -40C to +85C 500 M minimum No evidence of breakdown Center contact 70.0mmax. Outer contact 20.0mmax. Meet the requirements of following spec. 1.5 max.(DC to 3GHz) 1.6 max.(3GHz to 6GHz) 0.3dB max.(DC to 3GHz) 0.5dB max.(3GHz to 6GHz) 250K cycles Voltage Rating Nominal Frequency Range Nominal Impedance Temperature Rating Insulation Resistance Withstanding Voltage Initial Contact Resistance (without conductor resistance) A> Voltage Standing Wave Ratio (V.S.W.R.) A> Insertion Ioss A> Durability 1/4 10+/-0.1 2-Di a.2.2 +/-0. Dia.1 1 .05+ 0.05 /-0.0 1 6+/-0.04 3.0 Dia.3.0 SMPM-Male Dia.1.8+/-0.1 4+/-0.1 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PU0076A Part Number : MM206621 Written by T.Yamamoto Checked by T.Kuriyama Date 22/Jun./2016 3. USE THIS PRODUCT 3.1 Attach to measurement machine MM206621 must be attached to machine at the two screw holes in probe flange (Figure 2). Using guide pins is recommended. The guide pins should not be above probe flange (Figure 3). SCREW HOLE Figure 2. Screw hole Guide pin should not be above probe flange Guide pin Figure 3. Positional relation between guide pin and probe flange 2/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PU0076A Part Number : MM206621 Written by T.Yamamoto Checked by T.Kuriyama Date 22/Jun./2016 3.2 The tolerance of position against SWH type receptacle 3.2.1 MM206621 has a centering function by its design, +/-0.4mm is permitted against the hole center of SWH type receptacle. Please avoid needless force to SMPM interface when MM206621 is disengaged from SWH type receptacle and comes back to its original position. To avoid the needless force, please use extension cable assembly, MXFLM3SH3000/ MXFJM3SJ3000 (Figure 4/Figure 5). Centering function +/-0.4mm may not be permitted against the hole center of SWH type receptacle, when MM206621 is affected by the needless force. Please hold the cable to keep some margin like this Cable holding point Over 30mm ve rR O MXFLM3SH3000 30 m m Over 50mm MM206621 To Measurement Equipment Figure 4. Instruction of MXFLM3SH3000 To Measurement Equipment MXFJM3SJ3000 MM206621 Figure 5. Instruction of MXFJM3SJ3000 Please use M19500 for un-mating MM206621 with MXFLM3SH3000/ MXFJM3SJ3000 (Figure 6). Figure 6. SMPM interface un-mating jig: M19500 3/4 Preliminary Specification of COAXIAL CONNECTOR Preliminary SPEC No. : NMM04-PU0076A Part Number : MM206621 Written by T.Yamamoto Checked by T.Kuriyama Date 22/Jun./2016 19.0 to 20.0 18.5 to 19.5 (Using Area) 20 3.2.2 To get 10dB or higher isolation (up to 6GHz), the engagement strokes from the flange to the tip of probe is 18.5mm to 19.5mm (Figure 7). 0+/-0.4 Mating Unmating Unit:mm Figure 7. Acceptable Engagement range to SWH type receptacle 3.3 The slant angle tolerance of probe against SWH type Receptacle (Figure 8) To have a stable measurement, slant angle of MM206621 must be within +/-2degree. 0+/-2 degre e Figure 8. Probe Shape Operation Manual for Auto Measurement probe (MM206621) 4/4