MM8130-2600RA2

!Note • This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Microwave Coaxial Connectors Murata Manufacturing Co., Ltd. Cat.No.O30E-8 O30E.pdf 07.9.3 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. for EU RoHS Compliant • • • All the products on this catalog are complied with EU RoHS. EU RoHS is "the European Directive 2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment". For more details, please refer to our website 'Murata's Approach for EU RoHS' (http://www.murata.com/info/rohs.html). PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. CONTENTS Part Numbering 1 2 1 2 Microwave Coaxial Connectors with Switch SWF Type 3 Notice 5 Package 8 Microwave Coaxial Connectors with Switch SWD Type 9 Notice 11 Package 14 Ultra Miniature SMT HSC Type 15 Notice 18 Package 21 Miniature SMT GSC Type 22 Notice 25 Package 28 SMT FSC Type 29 Notice 32 Package 35 2 3 4 3 5 4 5 Miniaturized Microwave Coaxial Connector Cable List 36 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. o Part Numbering Coaxial Connectors (Chip Type Receptacle) (Part Number) R A1 MM 7329 -27 00 q w e r t y tPackage Product ID qProduct ID Product ID MM Microwave Coaxial Connectors (Chip Type Receptacle) Code Package Product ID B Bulk R Reel yPackage Detail wSeries Code Series Code Package Detail 4829 HSC Type A1 FSC, SWD, GSC Type 1000pcs. /Reel (ø178mm) 7329 FSC Type A4 HSC Type, 4000pcs. /Reel (ø178mm) 8130 SWF Type B0 HSC Type, 10000pcs. /Reel (ø330mm) 8430 SWD Type B3 SWD Type, 3000pcs. /Reel (ø330mm) 9329 GSC Type B4 FSC Type, 4000pcs. /Reel (ø330mm) B5 GSC Type, 5000pcs. /Reel (ø330mm) B8 SWF Type, 8000pcs. /Reel (ø330mm) eIndividual Specification Code (1) Code Individual Specification Code (1) -26 Switch Connector SMD Type -27 Connector SMD Type rIndividual Specification Code (2) Code Individual Specification Code (2) 00 Serial Coaxial Connectors (with Cable) (Part Number) MX FG 76 q w e r t y rConnector (2) qProduct ID Product ID MX Coaxial Connectors (with Cable) wConnector (1) Code Connector (2) FG FSC Type for 76 Cable FK FSC Type for 81 Cable HP HSC Type Code Connector (1) TK GSC Type FG FSC Type for 76 Cable XX None Connector FK FSC Type for 81 Cable HP HSC Type TK GSC Type eCable Code Cable 32 76 tLength Expressed by four figures. The unit is mm. From first to third figures are significant, and the fourth figure expresses the number of zeros which follow the three figures. Ex.) Code Length 0.4D, PFA, Single Shield Line, Spiral 5000 500mm = 500 x 100 0.8D, FEP, Single Shield Line 1001 1000mm = 100 x 101 81 0.4D, FEP, Single Shield Line 88 0.4D, PFA, Single Shield Line, Single Line 92 0.4D, PFA, Single Shield Line, Spiral yIndividual Specification Code Expressed by two sign. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Microwave Coaxial Connectors 1 Microwave Coaxial Connectors with Switch SWF Type 2.5±0.2 C Terminal Side 1. The coaxial connector with switch is very useful for characteristic measurement Cellular phone and microwave circuit. 2. It is possible to switch the line connection and disconnection easily by special probe. 3. Small size, low profile, size 2.5x2.5x1.4mm (LxWxH) 4. Excellent characteristics, low IL 0.2dB max. V.S.W.R. 1.3 max. Isolation 15dB min. (DC to 6GHz) 5. Surface mountable and reflow solderable 6. Tape package available R Terminal Side 2.5±0.2 ■ Features 0.8±0.2 1.4±0.1 Dia. 2.1±0.2 IN OUT MM8130-2600 GROUND (in mm) ■ Applications Cellular phone, W-LAN, Other wireless and measurement equipment Part Number MM8130-2600 Rated Contact Withstand Insulation Durability Frequency Temperature Voltage Resistance Voltage Resistance Range Rating (Vrms) (max.) (ohm) (Vrms) (M ohm) (cycles) (degree C) 250 0.07 300 (AC) 500 100 to 6GHz -40 to +85 Insertion Loss (On) (dB) VSWR Isolation (Off) (dB) Inner Electrode (C) Inner Electrode (R) (material) Outer Electrode (material) 1.2 max. 0.1 max. 20 min. Stainless Steel Stainless Steel Copper Alloy (DC to 3GHz) (DC to 3GHz) (DC to 3GHz) Gold plated Gold plated Gold plated Impedance: 50ohm ■ Measurement Probe Dimensions MXHS83QE3000 300±4 (32) Dia. 3.8±0.1 Dia. 5.4±0.1 5 .1 ±0 .6 .2 ia D 2- Dia . 19 D .68 ia ±0. .1 2 0± 0. 2 MM126036 (26) (7.1) 3.1±0.1 15.2±0.2 (4.02) 9±0.2 Dia. 7±0.1 9±0.2 16±0.15 SMA-J 0.8D Cable SMA-J (13.35) 11.85±0.2 21.65±0.3 Dia. 3.2±0.1 (33.5) Dia. 4.3±0.1 Dia. 5.8±0.2 (in mm) (in mm) Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. ■ Measurement Probe Dimensions ■ Structure MXHS83QH3000 300±4 (32) (26) 0.8D Cable 20.1±0.2 13.9±0.2 12±0.2 3.1±0.1 Probe SMA-J OUT Dia. 3.2±0.1 Dia. 3.4±0.1 Dia. 4.3±0.1 Dia. 5.8±0.2 IN IN OUT Without Probe With Probe (in mm) ■ Standard Land Dimensions 1. Standard Pattern Dimensions I/O pattern should be designed to match 50 ohm impedance circuit. 4 2.8 1.3 0.5 Typical PCB material is glass epoxy (εr=4.8). Thickness is 1.0mm. The solder resist should be printed except for the land 1.74 2.9 4.14 3.44 2.7 1.1 pattern on the PCB. Land 0.5 1.74 0.5 Electrode (in mm) 2. Standard Solder Stencil Mask Pattern Follow standard solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 2.7 1.1 2.14 0.28 2.7 1 1.3 2.48 Standard Solder Stencil Mask Pattern (Mask thickness 0.12mm) (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Storage and Operating Condition) 1. Environment Conditions (1) This product is designed for use in electrical equipment in the environment (temperature, humidity, atmospheric pressure, etc.) specified in this approval drawing. It may not be used in the following environments or under the following conditions: (a) Ambient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (b) Ambient air containing volatile or combustible gas (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles (e) In direct sunlight (f) Dusty conditions (g) In freezing (h) Other environments similar to the above conditions (2) Contact the manufacturer before using the product in any of the above environments or under any of the above conditions. 2. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use if the product has been stored for more than 6 months. Temperature: -10 to +40 degree C Humidity: 15 to 85% RH 1 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Soldering and Mounting) 2. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 150D Time 60 to 120 s. Soldering Temperature (at the tip of the soldering iron) less than 350D Time less than 3 s. 3. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering. 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. Allowable Temperature and Time of Reflow Soldering 260 250 Temperature (D) 1. Reflow soldering Soldering must be carried out without exceeding the allowable soldering temperature and time shown within the shaded area of Figure "Allowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in Figure "Allowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in Figure "Reflow Soldering Standard Conditions". Follow standard solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 240 230 220 210 200 190 180 30 60 90 120 Time (sec.) 150 180 210 240 Solder: Sn-3.0Ag-0.5Cu Reflow Soldering Standard Conditions Peak temperature 250±5D Temperature (D) 1 240 230 150 Pre-heating 150±20D 100 25 0 Time (sec.) 30 sec. max. 60-120 sec. 30-50 sec. Measuring point of temperature: In-Out Terminals of the Device Reflow Soldering: Both Convection and Infrared Rays : Hot Air : Hot Plate 5. Please note the following in case of soldering terminals or leads of the product. (1) Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.20wt%). (2) Flux should be thoroughly cleaned from connector to prevent possible deterioration of electrical characteristics. 6. Please mount this product at the position so that stress by wrap and/or bend of the PCB may not apply to it. 7. Please avoid the cleaning of this product. Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice Continued from the preceding page. ■ Notice(Handling) Fig. 1 Insertion the Automatic Measurement Probe (MM126036) in Receptacle (MM8130-2600) 18.28(Minimum Point for Using) 0±2° 19.78(Maximum Point for Using) 1. Automatic Measurement Probe (MM126036) Automatic measurement probe (MM126036) should be used on the condition in Fig. 1 for good connection without any damages. The engagement strokes from the flange to the tip of probe is 18.28mm to 19.78mm with vertical (0+/-2 degree) direction. 1.5 (Using Range) (in mm) 2. L Type Probe with Locking Function (MXHS83QE3000, MXHS83QH3000) Do not try to pull the cable, when a connector with a coaxial cable is handled. Do not give a twisted torque to the cable and connector. Mechanical stress: The stress to the connector should be limited as figure shown right. (1) Stress to the housing. Stress A and B: 0.5N max. (2) Stress to the outer sleeve. Stress C: 0.6N max. Stress D: 0.6N max. (3) Cable pull strength. Stress E: 0.5N max. 3. Usage Condition (1) Do not apply electrical voltage greater than specified in the catalog. It might cause degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. (2) Confirm that product perfomance is not influenced with any other components or materials which directly contact products. 4. Handling Do not apply excessive shock or load to subassembly products such as soldered printed circuit board in case handling or transporting. Mechanical Stress after Engagement C B A E D MM8130-2600 PCB 1 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Package ■ Dimensions of Reel ■ Dimensions of Taping P0 D0 T E P2 D B N W F 5° max. W1 5° max. B A 1 C P1 A K W2 Part Number MM8130-2600RB8 Tolerance A 330 ±2.0 B 13 ±0.5 C 21 ±0.8 D 2 ±0.5 N (min.) Dia. 100 ±1.0 W1 9.4 ±1.0 W2 (max.) 13.4 ±1.0 (in mm) ■ Minimum Quantity MM8130-2600RB8: 330 mm dia.reel/8000 pcs. MM8130-2600B: Bulk/free A B 2.8±0.1 2.8±0.1 P0 4±0.1 P1 4±0.1 W 8±0.2 D0 E F K Dia.1.5+0.1 1.75±0.1 3.5±0.1 1.6±0.1 P2 2±0.1 T 0.25±0.05 (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Microwave Coaxial Connectors Microwave Coaxial Connectors with Switch SWD Type 3±0.1 B ■ Features R Terminal Side 3±0.1 C Terminal Side 1. The coaxial connector with switch is very useful for characteristic measurement of hand held phone and microwave circuit. 2. It is possible to switch the line connection and disconnection easily by special probe. 3. Small size, low profile, size 3x3x1.75mm (LxWxH) 4. Excellent characteristics, low IL 0.2dB max. V.S.W.R. 1.3 max. Isolation 15dB min. (DC to 6GHz) 5. Surface mountable and reflow solderable 6. Tape package available A 2 IN OUT GROUND A 1.75±0.15 0.8±0.2 B dia 2.1±0.2 MM8430-2610 (in mm) ■ Applications Cellular phone, W-LAN, Other wireless and measurement equipment Part Number MM8430-2610 Rated Contact Withstand Insulation Durability Frequency Temperature Voltage Resistance Voltage Resistance Range Rating (Vrms) (max.) (ohm) (Vrms) (M ohm) (cycles) (degree C) 250 0.05 300 (AC) 500 500 to 6GHz -40 to +85 Insertion Loss (On) (dB) VSWR Isolation (Off) (dB) Inner Electrode (C) Inner Electrode (R) (material) Outer Electrode (material) 1.2 max. 0.1 max. 20 min. Stainless Steel Copper Alloy Copper Alloy (DC to 3GHz) (DC to 3GHz) (DC to 3GHz) Gold plated Gold plated Silver plated Impedance: 50ohm ■ Measurement Probe Dimensions MXHS83QE3000 300±4 (32) 6± 2. 15 0. Dia. 3.8±0.1 Dia. 5.4±0.1 . ia D 2- Dia . 19 D .68 ia ±0. .1 2 0± 0. 2 MM126036 (26) (7.1) 3.1±0.1 15.2±0.2 (4.02) 9±0.2 Dia. 7±0.1 9±0.2 16±0.15 SMA-J 0.8D Cable SMA-J (13.35) 11.85±0.2 21.65±0.3 Dia. 3.2±0.1 (33.5) Dia. 4.3±0.1 Dia. 5.8±0.2 (in mm) (in mm) Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. ■ Measurement Probe Dimensions ■ Structure MXHS83QH3000 300±4 (32) 0.8D Cable 20.1±0.2 13.9±0.2 12±0.2 3.1±0.1 Probe SMA-J OUT Dia. 3.2±0.1 Dia. 3.4±0.1 Dia. 4.3±0.1 Dia. 5.8±0.2 IN IN OUT Without Probe With Probe (in mm) ■ Standard Land Dimensions 1. Standard pattern dimensions I/O pattern should be designed to match 50 ohm impedance 4 circuit. 2 1 Typical PCB material is glass epoxy (εr=4.8). Thickness is Through hole 0.5 1.0mm. The solder resist should be printed except for the land 4.1 3.1 1 2.1 1 pattern on the PCB. 3 Land Electrode (1.5) (1.5) 1.74 (in mm) 2. Standard solder stencil mask pattern Follow Standard solder stencil mask pattern to avoid the 1 2.3 3 0.5 possibility of solder being trapped under connector. 3.5 2 (26) 2 3.5 The Standard solder stencil mask pattern (Mask thickness 0.15mm) (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Storage and Operating Condition) 1. Environment Conditions (1) This product is designed for use in electrical equipment in the environment (temperature, humidity, atmospheric pressure, etc.) specified in this approval drawing. It may not be used in the following environments or under the following conditions: (a) Ambient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (b) Ambient air containing volatile or combustible gas (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles (e) In direct sunlight (f) Dusty conditions (g) In freezing (h) Other environments similar to the above conditions (2) Contact the manufacturer before using the product in any of the above environments or under any of the above conditions. 2. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use if the product has been stored for more than 6 months. Temperature: -10 to +40 degree C Humidity: 15 to 85% RH 2 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Soldering and Mounting) 2. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 150D Time 60 to 120 s. Soldering Temperature (at the tip of the soldering iron) less than 350D Time less than 3 s. 3. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering. 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. Allowable Temperature and Time of Reflow Soldering 260 Temperature (D) 250 240 230 220 210 200 190 180 30 60 90 120 Time (sec.) 150 180 210 240 Solder: Sn-3.0Ag-0.5Cu Reflow Soldering Standard Conditions Peak temperature 250±5D Temperature (D) 2 1. Reflow soldering Soldering must be carried out without exceeding the allowable soldering temperature and time shown within the shaded area of Figure "Allowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in Figure "Allowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in Figure "Reflow Soldering Standard Conditions". Follow standard solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 240 230 150 Pre-heating 150±20D 100 25 0 Time (sec.) 30 sec. max. 60-120 sec. 30-50 sec. Measuring point of temperature: In-Out Terminals of the Device Reflow Soldering: Both Convection and Infrared Rays : Hot Air : Hot Plate 5. Please note the following in case of soldering terminals or leads of the product. (1) Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.20wt%). (2) Flux should be thoroughly cleaned from connector to prevent possible deterioration of electrical characteristics. 6. Please mount this product at the position so that stress by wrap and/or bend of the PCB may not apply to it. 7. Please avoid the cleaning of this product. Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice Continued from the preceding page. Notice (Handling) Fig. 1 Insertion the Automatic Measurement Probe (MM126036) in Receptacle (MM8430-2610) 2 18.28(Minimum Point for Using) 0±2° 19.78(Maximum Point for Using) 1. Automatic Measurement Probe (MM126036) Automatic measurement probe (MM126036) should be used under conditions in Fig. 1 for good connection without any damages. The engagement strokes from the flange to the tip of probe is 18.28mm to 19.78mm with vertical (0±2°) direction. 1.5 (Using Range) 2. L Type Probe with Locking Function (MXHS83QE3000, MXHS83QH3000) Avoid pulling cable when probe is locked into connector. Avoid twisting probe or cable when engaging or disengaging from connector. Mechanical stress: The stress to the connector should be limited as figure shown right. (1) Stress to the housing. Stress A and B: 0.5N max. (2) Stress to the outer sleeve. Stress C: 0.6N max. Stress D: 0.6N max. (3) Cable pull strength. Stress E: 0.5N max. 3. Usage Condition (1) Do not apply electrical voltage greater than specified in the catalog. It might cause degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. (2) Confirm that product performance is not influenced with any other components or materials which directly contact products. 4. Handling Avoid excessive stress when handling and transporting printed circuit board after connector and/or assembly has been secured to PCB. Mechanical stress after engagement C B A E D MM8430-2610 PCB PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Package ■ Dimensions of Taping D D0 B A N F W1 C P1 T A B 2 P0 E P2 W 3 degree Max. 3 degree Max. ■ Dimensions of Reel K W2 (in mm) (in mm) Murata Part Number MM8430-2610RA1 MM8430-2610RB3 TOLERANCE A 178 330 ±2.0 B 13 13 ±0.5 C 21 21 ±0.8 D 2 2 ±0.5 N (min.) Dia. 50 Dia. 50 – W1 13.5 13.5 ±1.5 ■ Minimum Quantity MM8430-2610RA1: dia.180 mm reel/1000 pcs. MM8430-2610RB3: dia.330 mm reel/3000 pcs. MM8430-2610B: Bulk/free W2 (max.) 18.5 18.5 – A B W 3.4±0.1 3.4±0.1 12±0.2 P0 4±0.1 P1 8±0.1 P2 2±0.1 D0 E F Dia.1.5+0.1 1.75±0.1 5.5±0.1 T 0.3±0.05 K 2.0±0.15 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Microwave Coaxial Connectors Ultra Miniature SMT HSC Type 2.06 ■ Features 0.85 1. The mating height is only 1.2mm maximum by new mechanical design. Suitable for low profile design. 2. New mating mechanical desigh makes stable feeling connection. 3. Soft and ultra thin 0.81mm diameter flexible coaxial cables is available. 4. High performance with wide frequency range(DC to 6GHz). VSWR at 3GHz to 6GHz is 1.45 maximum. (2.1 dia.) 2.34±0.5 3 MXHP (in mm) ■ Applications Portable telephone, cordless telephone(analog and digital), GPS, and other microwave radio and measurement equipment. 0.7 0.4 2 1.4 0.8 Dia. 0.5 2 1.52 0.6 1.5 Dia. Hot Terminal Ground Terminal MM4829-2702 Tolerances Unless Otherwise Specified: ±0.2 (in mm) Part Number MM4829-2702 Rated Contact Withstanding Insulation Durability Frequency Temperature Voltage Resistance (max.) Voltage Resistance (min.) Rating Range (cycles) (V) (ohm) (rms) (M ohm) (GHz) (degree C) 250 0.020 300 (AC) 500 30 Impedance: 50ohm ■ Measurement Adapter Dimensions (for Receptacle) MM121490 (Hand measurement) 13.3±0.15 SMA-J Dia. 5.33±0.1 Dia. 5.33±0.2 2±0.1 Dia. 3.0±0.1 Dia. 2.5±0.1 HSC-Female (4.3) MM121491 (Automatic measurement) Dia. 5.33±0.2 5.65±0.1 Dia. 6.5±0.2 7.91±0.1 Dia. 5.33±0.1 2±0.2 Dia. 3±0.1 HSC-CONTACT 17.96±0.2 SMA-J (in mm) to 6.0 -40 to +85 VSWR Center Contact Outer Contact Insulator 1.3 max. (DC to 3GHz) Copper Alloy Gold plated Copper Alloy Silver plated Engineering plastic PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. ■ Measurement Adapter Dimensions (for Cable Assembly) ■ Cable Length Tolerance MM121500 (Hand measurement) HSC-Male 12.95±0.2 0.4±0.05 8.55±0.4 Dia. 1.5±0.02 L Dia. 5.33±0.2 SMA-J Cable Length L (mm) Over Less than Dimensional Tolerance (mm) ±3 20 100 100 500 ±4 500 1000 ±10 1000 – +2% of L –0% of L (in mm) 3 45 2.9 35 HSC (in mm) 1.2 max. 5 3 D ia .2 .7 6.0 ■ Profile Dimensions 1.85 max. ■ Disengagement Tool (Part Number: M19100) (in mm) Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. ■ Land Pattern Dimensions 1. Standard pattern dimensions I/O pattern should be designed to match 50 ohm impedance circuit. Typical PCB material is glass epoxy (εr=4.8). Thickness is 1.34 2.5 1.5 0.5 0.54 0.38 The solder resist should be printed except for the land 0.75 1.25 1.0mm. 0.7 1.25 (1.81) 1.58 pattern on the PCB. 0.6 (1.74) (1.5) Land (1.5) Electrode (in mm) 2. Standard solder stencil mask pattern Follow Standard solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 2.5 1.5 0.38 0.84 0.9 2.4 0.82 Ground 0.36 Hot The standard solder stencil mask drawing (Mask thickness 0.12mm) (in mm) 3 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Storage and Operation Condition) 3 1. Environment Conditions (1) This product is designed for use in electrical equipment in the environment (temperature, humidity, atmospheric pressure, etc.) specified in this approval drawing. It may not be used in the following environments or under the following conditions: (a) Ambient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (b) Ambient air containing volatile or combustible gas (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles (e) In direct sunlight (f) Dusty conditions (g) In freezing (h) Other environments similar to the above conditions (2) Contact the manufacturer before using the product in any of the above environments or under any of the above conditions. 2. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use if the product has been stored for more than 6 months. Temperature: -10 to +40 degree C Humidity: 15 to 85% RH PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Soldering and Mounting) 2. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 150D Time 60 to 120 s. Soldering Temperature (at the tip of the soldering iron) less than 350D Time less than 3 s. Allowable Temperature and Time of Reflow Soldering 260 Temperature (D) 250 240 230 220 210 200 190 180 30 60 90 120 Time (sec.) Peak temperature 250±5D 240 230 150 Pre-heating 150±20D 100 25 0 Time (sec.) 30 sec. max. 60-120 sec. 3. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering. 150 180 210 240 Solder : Sn-3.0Ag-0.5Cu Reflow Soldering Standard Conditions Temperature (D) 1. Reflow soldering Soldering must be carried out without exceeding the allowable soldering temperature and time shown within the shaded area of Figure "Allowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in Figure "Allowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in Figure "Reflow Soldering Standard Conditions". Use the Pattern and Metal mask pattern is illustrated in details. Follow standard solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 30-50 sec. Measuring point of temperature : In-Out Terminals of the Device Reflow Soldering : Both Convection and Infrared Rays : Hot Air : Hot Plate 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. 5. Please note the following in case of soldering terminals or leads of the product. (1) Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.20wt%). (2) Flux should be thoroughly cleaned from connector to prevent possible deterioration of electrical characteristics. 6. Please mount this product at the position so that stress by wrap and/or bend of the PCB may not apply to it. 7. Please dry out this product immediately after soldering and cleaning. Continued on the following page. 3 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice Continued from the preceding page. ■ Notice (Handling) 1. Usage Condition (1) Do not apply electrical voltage greater than specified in the drawing. It might cause degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. (2) Confirm product's performance is not influenced by contact of other components. (3) Please contact the manufacturer beforehand, if the product is to be used in frequently bent position. 3 2. Handling (1) Avoid excessive stress when handling and transporting printed circuit board after connector and/or assembly has been secured to PCB. (2) Do not try to pull the cable, when a connector with a coaxial cable is handled. (3) Disregarding the following notes could cause mechanical damage and/or poor electrical performance. 3. Handling Instructions (1) Cable is designed to fit only with MM4829-2702 receptacle. Any other receptacle cannot be used with this cable. (2) Disengagement: Use tool P/N M19100 to insert or remove cable in a vertical direction from receptacle. Avoid pulling only the cable to prevent cable damage. (3) Avoid twisting probe or cable when engaging or disengaging from connector. (4) Mechanical stress: The stress to the connector should be limited as shown in Figure 1. (a) Stress to the housing. Stress A and B: 5.0N max. (b) Stress to the outer sleeve. Stress C: 1.0N max. Stress D: 1.0N max. (c) Cable pull strength. Stress E: 5.0N max. Figure 1. Mechanical stress after engagement A C B E D PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Package ■ Dimensions of Taping D0 B A N F W1 C P1 A W2 T B D P0 E P2 W 3° max. 3° max. ■ Dimensions of Reel K (in mm) (in mm) Murata Part Number A MM4829-2702RA4 180 +0/-3 MM4829-2702RB0 330 TOLERANCE ±2.0 B 13 13 ±0.2 C 21 21 ±0.8 D 2 2 ±0.5 N (min.) W1 W2 (max.) Dia. 60 +1/0 9 ±0.3 11.4 Dia. 100 9.4 13.4 ±1.0 ±1.0 ±1.0 ■ Minimum Quantity MM4829-2702RA4: 180 mm dia. reel/4000 pcs. MM4829-2702RB0: 330 mm dia. reel/10000 pcs. MM4829-2702B: Bulk/free A B W 2.35±0.1 2.35±0.1 8±0.2 P0 4±0.1 P1 4±0.1 P2 2±0.1 D0 E F K Dia.1.5 +0.1 1.75±0.1 3.5±0.1 0.75±0.15 -0 T 0.25±0.05 3 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Microwave Coaxial Connectors Miniature SMT GSC Type 2.8 ■ Features 1.5 1. The mating height is only 2mm maximum by new mechanical design. Suitable for low profile design. 2. New mating mechanical desigh makes stable feeling connection. 3. Soft and ultra thin 0.8mm diameter flexible coaxial cables is available. 4. High performance with wide frequency range(DC to 6GHz). VSWR at DC to 3GHz is 1.2 maximum. VSWR at 3GHz to 6GHz is 1.3 maximum. ø2.55 3.5±0.5 MXTK Tolerances unless otherwise specified : ±0.3 (in mm) ■ Applications Portable telephone, cordless telephone(analog and digital), GPS, and other microwave radio and measurement equipment. (R0.15) 0.15±0.03 0.5±0.1 2.1 2.6 3 ø1±0.1 2.3 (R0.15) 0.12±0.03 ø2.1 MM9329-2700 0.5±0.1 Hot Terminal Ground Terminal 1.15 0.15±0.03 2.6 3 Tolerances Unless Otherwise Specified: ±0.2 (in mm) Rated Contact Withstanding Insulation Durability Frequency Temperature Voltage Resistance (max.) Voltage Resistance (min.) Rating Range (cycles) (V) (ohm) (rms) (M ohm) (GHz) (degree C) Part Number MM9329-2700 250 0.015 300 (AC) 500 100 to 6.0 -40 to +90 VSWR Center Contact Outer Contact Insulator 1.2 max. (DC to 3GHz) Copper Alloy Gold plated Copper Alloy Silver plated Engineering plastic Impedance: 50ohm ■ Measurement Adapter Dimensions (for Receptacle) MM121470 (Hand measurement) MM121471 (Automatic measurement) 18.24 13.4 5.08 SMA-JACK 5.08 7.4 4.4 SMA-JACK 2 8.19 2.3 ø6.5 ø4.06 ø5.33 ø5.33 ø5.33 ø3 ø4.6 ø2.55 2.1 ø5.33 4 (in mm) Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. ■ Measurement Adapter Dimensions (for Cable Assembly) ■ Cable Length Tolerance L MM121480 13.4 0.85 8.55 5.08 ø5.33 SMA-JACK Over ø2.1 ø5.33 Cable Length L (mm) (∗) (in mm) Till Dimensional tolerance (mm) 40 100 ±3 100 500 ±4 500 1000 1000 – ±10 +2% of L –0% of L ∗L must be 20mm Min. ■ Disengagement Tool (Part Number: M22001) 1) (C 4 35±2 2.3±0.6 0.5±0.6 (Dia. 8) 7.95±2 3.9±0.6 45±2 (in mm) 0.7 min. 2 max. 2.8 max. ■ Profile Dimensions (in mm) Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. ■ Land Pattern Dimensions 1. Standard pattern dimensions I/O pattern should be designed to match 50 ohm impedance circuit. Typical PCB material is glass epoxy (εr=4.8). Thickness is ø1 1.0mm 5.2 3.8 2.3 1 0.6 (3-ø0.6) (Through Holes) (2.37) 2 1.9 1.5 1.5 1.05 1.05 pattern on the PCB. 2.5 The solder resist should be printed except for the land Land Electrode 0.6 (1.5)(1.74)(1.5) (in mm) 2. Standard solder stencil mask pattern Follow Standard solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 3.3 2.3 1.05 0.45 0.6 1.5 1.05 4 0.6 The standard solder stencil mask drawing (Mask thickness 0.15mm) (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Storage and Operation Condition) 1. Environment Conditions (1) This product is designed for use in electrical equipment in the environment (temperature, humidity, atmospheric pressure, etc.) specified in this approval drawing. It may not be used in the following environments or under the following conditions: (a) Ambient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (b) Ambient air containing volatile or combustible gas (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles (e) In direct sunlight (f) Dusty conditions (g) In freezing (h) Other environments similar to the above conditions (2) Contact the manufacturer before using the product in any of the above environments or under any of the above conditions. 2. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use if the product has been stored for more than 6 months. Temperature: -10 to +40 degree C Humidity: 15 to 85% RH 4 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Soldering and Mounting) Allowable Temperature and Time of Reflow Soldering 260 250 Temperature (D) 1. Reflow soldering Soldering must be carried out without exceeding the allowable soldering temperature and time shown within the shaded area of Figure "Allowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in Figure "Allowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in Figure "Reflow Soldering Standard Conditions". Follow recommended solder stencil mask pattern to avoid the possibility of solder being trapped under connector. 240 230 220 210 200 190 180 30 60 90 120 Time (sec.) 150 180 210 240 Solder : Sn-3.0Ag-0.5Cu Reflow Soldering Standard Conditions 3. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering. Peak temperature 250±5D Temperature (D) 4 2. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 150D Time 60 to 120 s. Soldering Temperature (at the tip of the soldering iron) less than 350D Time less than 3 s. 240 230 150 Pre-heating 150±20D 100 25 0 Time (sec.) 30 sec. max. 60-120 sec. 30-50 sec. Measuring point of temperature : In-Out Terminals of the Device Reflow Soldering : Both Convection and Infrared Rays : Hot Air : Hot Plate 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. 5. Please note the following in case of soldering terminals or leads of the product. (1) Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.20wt%). (2) Flux should be thoroughly cleaned from connector to prevent possible deterioration of electrical characteristics. 6. Please mount this product at the position so that stress by wrap and/or bend of the PCB may not apply to it. 7. Please dry out this product immediately after soldering and cleaning. Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice Continued from the preceding page. ■ Notice (Handling) 1. Usage Condition (1) Do not apply electrical voltage greater than specified in the drawing. It might cause degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. (2) Confirm product's performance is not influenced by contact of other components. (3) Please contact the manufacturer beforehand, if the product is to be used in frequently bent position. 2. Handling (1) Avoid excessive stress when handling and transporting printed circuit board after connector and/or assembly has been secured to PCB. (2) Do not try to pull the cable, when a connector with a coaxial cable is handled. (3) Disregarding the following notes could cause mechanical damage and/or poor electrical performance. 3. Handling Instructions (1) Cable is designed to fit only with MM9329-2700 receptacle. Any other receptacle cannot be used with this cable. (2) Disengagement: Use tool P/N M22001 to insert or remove cable in a vertical direction from receptacle. Avoid pulling only the cable to prevent cable damage. (3) Avoid twisting probe or cable when engaging or disengaging from connector. (4) Mechanical stress: The stress to the connector should be limited as shown in Figure 1. (a) Stress to the housing. Stress A and B: 5.0N max. (b) Stress to the outer sleeve. Stress C: 3.0N max. Stress D: 2.0N max. (c) Cable pull strength. Stress E: 5.0N max. 4 Figure 1. Mechanical Stress after Engagement A C B E D PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Package ■ Dimensions of Taping D0 B W 3° max. N F W1 A T B D P0 E P2 3° max. ■ Dimensions of Reel C P1 A W2 K (in mm) (in mm) Murata Part Number MM9329-2700RA1 MM9329-2700RB5 TOLERANCE A 178 330 ±2.0 B 13 13 ±0.5 C 21 21 ±0.8 D 2 2 ±0.5 N (min.) Dia. 50 Dia. 50 – W1 13.5 13.5 ±1.5 ■ Minimum Quantity 4 MM9329-2700RA1: dia.180 mm reel/1000 pcs. MM9329-2700RB5: dia.330 mm reel/5000 pcs. MM9329-2700B: Bulk/free W2 (max.) 18.5 18.5 – A B W D0 E F K 3.4±0.1 3.4±0.1 12±0.2 Dia.1.5 +0.1 1.75±0.1 5.5±0.1 1.25±0.15 -0 P0 4±0.1 P1 8±0.1 P2 2±0.1 T 0.3±0.05 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Microwave Coaxial Connectors SMT FSC Type 2.4 ■ Features 2.4 1. High engagement 2. Miniature (LxWxH: 3.4x3.4x1.5mm) for High density mounting 3. Low profile (3.0mm max.) 4. SMD and reflow soldering applicable 5. Taping package applicable 6. Mountable by automatic placer 7. High performance (V.S.W.R. 1.3 max. at 3GHz) 8. Matched with ultra-thin FEP coaxial cables (0.8mm dia) ø2.2 3.8 MXFG76_/MXFK81_ Tolerances Unless Otherwise Specified:±0.3 (in mm) ■ Applications 2.4 3.4 1 2.4 3.4 Portable telephone, mobile telephone, cordless telephone, GPS, and other microwave radio and measurement equipment. 0.5 1.5 5 Hot Terminal 0.5 Ground Terminal MM7329-2700 Tolerances Unless Otherwise Specified:±0.2 (in mm) 3.4 3.2 0.1max 0.5 0.4 2.9 (3) 0.2max 2.4 0.5 0.5 2.4 (1) (2) 1.5 MM7329-2702 : Hot Terminal : Ground Terminal TOLERANCES UNLESS OTHERWISE SPECIFIED : ±0.2 (in mm) Part Number Rated Contact Withstanding Insulation Durability Frequency Temperature Voltage Resistance (max.) Voltage Resistance (min.) Rating Range (cycles) (V) (ohm) (rms) (M ohm) (GHz) (degree C) VSWR Center Contact Outer Contact Insulator MM7329-2700 250 0.015 300 (AC) 500 50 to 3.0 -40 to +90 1.3 max. Copper Alloy Gold plated Copper Alloy Gold plated Engineering plastic MM7329-2702 250 0.015 300 (AC) 500 50 to 3.0 -40 to +90 1.3 max. Copper Alloy Gold plated Copper Alloy Gold plated Engineering plastic Impedance: 50ohm PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. ■ Measurement Adapter Dimensions for Receptacle for Cable Assembly MM121454 (For FSC type receptacle) MM121460 (For FSC type cable assembly) 14.06 13.93 5.08 8.64 4.4 2.5 SMA-JACK 5.08 1.48 0.76 1.33 ø5.33 ø3.1 ø5.33 2.5 ø2.16 ø5.33 ø5.33 SMA-JACK (in mm) (in mm) ■ Land Pattern Dimensions MM7329-2700B 5.2 4.2 3.4 2.4 1 MM7329-2702B 5.2 4.2 2.4 1 3-ø0.6 (Through hole) .6 ø0 0.6 2.4 0.3 1.2 0.5 2.57 1.7 2.2 3.4 0.9 1.7 2.5 2.5 ø1 Land Land Electrode Electrode (in mm) (Note) · Pattern should be designed to match 50 ohm impedance circuit. · Typical PCB material is glass epoxy (εr=4.8). Thickness is 1.0mm. · The solder resist should be printed except for the land pattern on the PCB. ■ Cable Length Tolerance (1.5) (1.5) (1.74) (in mm) (Note) · Pattern should be designed to match 50 ohm impedance circuit. · Typical PCB material is glass epoxy (εr=4.8). Thickness is 1.0mm. · The solder resist should be printed except for the land pattern on the PCB. ■ Profile Dimensions 3 max. L Profile Cable Length L(mm)(∗) Over 40 Till 100 500 100 500 1000 1000 − ∗L must be 40mm Min. Dimensional tolerance(mm) ±3 ±4 ±10 +2% of L −0% of L 4.2 min. 5 0.6 (1.5) (1.74) (1.5) Clearance for mating (in mm) Continued on the following page. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. ■ Disengagement Tool M19000 (for MM7329-2700) 5±0.6 .7 20±2 T1 5±1 2±0.6 0.5±0.6 ø2 How to use tool (for MM7329-2700) 3.5±0.6 5±0.6 45±2 (in mm) M19004 (for MM7329-2702) How to use tool (for MM7329-2702) M19004 (10) (3) (105) 5 (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Storage and Operating Condition) 5 1. Environment Conditions (1) This product is designed for use in electrical equipment in the environment (temperature, humidity, atmospheric pressure, etc.) specified in this approval drawing. It may not be used in the following environments or under the following conditions: (a) Ambient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (b) Ambient air containing volatile or combustible gas (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles (e) In direct sunlight (f) Dusty conditions (g) In freezing (h) Other environments similar to the above conditions (2) Contact the manufacturer before using the product in any of the above environments or under any of the above conditions. 2. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use if the product has been stored for more than 6 months. Temperature: -10 to +40 degree C Humidity: 15 to 85% RH PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice ■ Notice (Soldering and Mounting) 2. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 150D Time 60 to 120 s. Soldering Temperature (at the tip of the soldering iron) less than 350D Time less than 3 s. 3. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering. 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. Allowable Temperature and Time of Reflow Soldering 260 Temperature (D) 250 240 230 220 210 200 190 180 30 60 90 120 Time (sec.) 150 180 210 240 Solder: Sn-3.0Ag-0.5Cu Reflow Soldering Standard Conditions Peak temperature 250±5D Temperature (D) 1. Reflow soldering Soldering must be carried out without exceeding the allowable soldering temperature and time shown within the shaded area of Figure "Allowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in Figure "Allowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in Figure "Reflow Soldering Standard Conditions". Follow Standard pattern dimensions. 240 230 150 Pre-heating 150±20D 100 25 0 Time (sec.) 30 sec. max. 60-120 sec. 30-50 sec. Measuring point of temperature: In-Out Terminals of the Device Reflow Soldering: Both Convection and Infrared Rays : Hot Air : Hot Plate 5. Please note the following in case of soldering terminals or leads of the product. (1) Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.20wt%). (2) Flux should be thoroughly cleaned from connector to prevent possible deterioration of electrical characteristics. 6. Please mount this product at the position so that stress by wrap and/or bend of the PCB may not apply to it. 7. Please dry out this product immediately after soldering and cleaning. Continued on the following page. 5 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice Continued from the preceding page. ■ Notice (Handling) 1. Usage Condition (1) Do not apply electrical voltage greater than specified in the drawing. It might cause degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. (2) Confirm product's performance is not influenced by contact of other components. (3) Please contact the manufacturer beforehand, if the product is to be used in frequently bent position. 2. Handling (1) Avoid excessive stress when handling and transporting printed circuit board after connector and/or assembly has been secured to PCB. (2) Do not try to pull the cable, when a connector with a coaxial cable is handled. (3) Disregarding the following notes could cause mechanical damage and/or poor electrical performance. Figure 1. Mechanical Stress after Engagement C (MM7329-2700) A B E D 5 3. Handling Instructions (1) Cable is designed to fit only with MM7329-2700 and MM7329-2702 receptacles. Any other receptacle can not be used with this cable. (2) Disengagement: Use tool P/N M19000 (for MM7329-2700) or M19004 (for MM7329-2702) to insert or remove cable in a vertical direction from receptacle. Avoid pulling only the cable to prevent cable damage. (3) Avoid twisting probe or cable when inserting or removing from receptacle. (4) Mechanical stress: The stress to the connector should be limited as shown in Figure 1. (a) Stress to the housing. Stress A and B: 4.9N max. (b) Stress to the outer sleeve. Stress C: 2.94N max. Stress D: 1.96N max. (c) Cable pull strength. Stress E: 7.84N max. (for MM7329-2700) 4.9N max. (for MM7329-2702) (MM7329-2702) B A D C E PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Package ■ Dimensions of Reel MM7329-2700RA1/RB4 D MM7329-2702RAB/RB2 D B B A A N W1 N W1 C C W2 W2 (in mm) Murata Part Number MM7329-2700RA1 MM7329-2700RB4 TOLERANCE A 178 330 ±2.0 B 13 13 ±0.5 C 21 21 ±0.8 D 2 2 ±0.5 N (min.) Dia. 50 Dia. 50 – W1 13.5 13.5 ±1.5 W2 (max.) 18.5 18.5 – (in mm) Murata Part Number MM7329-2702RAB MM7329-2702RB2 TOLERANCE A 178 330 ±2.0 B 13 13 ±0.5 C 21 21 ±0.8 D 2 2 ±0.5 N (min.) Dia. 50 Dia. 50 – W1 13.5 13.5 ±1.5 W2 (max.) 18.5 18.5 – ■ Dimensions of Taping P0 D T B W F E P2 5 P1 A A B W D E F K 3.9±0.1 3.7±0.1 12±0.2 ø1.5+0.1 1.75±0.1 5.5±0.1 3±0.15 −0 P1 8±0.1 P2 T 2±0.1 0.3±0.05 ■ Minimum Quantity MM7329-2700RA1: dia.180 mm reel/1000 pcs. MM7329-2700RB4: dia.330 mm reel/4000 pcs. MM7329-2700B: Bulk/free MM7329-2702RAB: dia.180 mm reel/ 500 pcs. MM7329-2702RB2: dia.330 mm reel/2000 pcs. MM7329-2702B: Bulk/free K P0 4±0.1 (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note O30E.pdf 07.9.3 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Miniaturized Microwave Coaxial Connector Cable List 0.8D single shield FEP cable Sheath 0.4D single shield PFA cable 0.4D single shield PFA cable 76 81 88 92 32 - Silver coated copper wire Silver coated copper covered steel wire Silver coated copper wire Silver coated copper wire (No./mm) 1/0.26 7/0.05 1/0.15 7/0.05 7/0.05 Total Dia. (mm) 0.26 0.15 0.15 0.15 0.15 Material - FEP FEP PFA PFA PFA 285 250 302-310 302-310 302-310 0.8 0.4 0.43 0.4 0.4 Material Inner conductor No. and Dia. Melting point Degree C (Reference only) Outer conductor 0.4D single shield PFA cable Silver coated copper covered steel wire Murata cable code Insulator 0.4D single shield FEP cable Total Dia. (mm) Material - Dia. of wire (mm) 0.05 0.05 0.05 0.05 0.05 Total Dia. (mm) 1.05 0.65 0.68 0.65 0.65 Material - FEP FEP PFA PFA PFA Nominal thickness (mm) 0.1 0.05 0.075 0.075 0.075 - Gray White White White White (mm) 1.24 0.8 0.83 0.8 0.8 3.3 Color Overall Dia. Tin plated copper wire Tin plated copper wire Tin plated copper wire Tin plated copper wire Silver plated copper wire Minimum bending radius (mm) 6 4.8 3.3 3.3 Nominal impedance (Ohm) 50 50 50 50 50 300 Vrms max. 300 Vrms max. 300 Vrms max. 300 Vrms max. 300 Vrms max. 100 Continuous operating voltage 100 100 100 100 dB/m at 1GHz 1.56 3.0 2.89 3.0 3.0 dB/m at 2GHz 2.3 4.26 4.28 4.26 4.26 dB/m at 3GHz 2.9 5.24 5.39 5.24 5.24 dB/m at 4GHz 3.5 6.18 6.44 6.18 6.18 8.4 9.17 9.17 Nominal static capacitance Nominal Insertion loss (pF/m) dB/m at 6GHz Assembly to FSC Suitable Suitable Not Suitable Not Suitable Not Suitable Assembly to GSC Not Suitable Not Suitable Suitable Suitable Not Suitable Assembly to HSC Not Suitable Not Suitable Not Suitable Not Suitable Suitable !Note • This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. O30E.pdf 07.9.3 Note: 1. Export Control For customers outside Japan No muRata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or otherwise contribution to (1) any weapons (Weapons of Mass Destruction (nuclear, chemical or biological weapons or missiles) or conventional weapons) or (2) goods or systems specially designed or intended for military end-use or utilization by military end-users. For customers in Japan For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required for export. < < > > 2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed above 3. Product specifications in this catalog are as of July 2007. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. 5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. http://www.murata.com/