MUR1100EG

MUR180E, MUR1100E SWITCHMODE Power Rectifiers Ultrafast “E” Series with High Reverse Energy Capability These state−of−the−art devices are designed for use in switching power supplies, inverters and as free wheeling diodes. Features • 10 mjoules Avalanche Energy Guaranteed • Excellent Protection Against Voltage Transients in Switching • • • • • • • http://onsemi.com ULTRAFAST RECTIFIERS 1.0 AMPERES, 800−1000 VOLTS Inductive Load Circuits Ultrafast 75 Nanosecond Recovery Time 175°C Operating Junction Temperature Low Forward Voltage Low Leakage Current High Temperature Glass Passivated Junction Reverse Voltage to 1000 V These are Pb−Free Devices* Mechanical Characteristics: • Case: Epoxy, Molded • Weight: 0.4 Gram (Approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal PLASTIC AXIAL LEAD CASE 59 Leads are Readily Solderable • Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds • Shipped in Plastic Bags; 1,000 per Bag • Available Tape and Reel; 5,000 per Reel, by Adding a “RL’’ Suffix to MARKING DIAGRAM the Part Number • Polarity: Cathode Indicated by Polarity Band MAXIMUM RATINGS Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Symbol MUR180E MUR1100E VRRM VRWM VR Value Unit V 800 1000 Average Rectified Forward Current (Note 1) (Square Wave Mounting Method #3 Per Note 3) IF(AV) 1.0 @ TA = 95°C A Non-Repetitive Peak Surge Current (Surge applied at rated load conditions, halfwave, single phase, 60 Hz) IFSM 35 A TJ, Tstg −65 to +175 °C Operating Junction Temperature and Storage Temperature Range Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%. A MUR1x0E YYWW G G A = Assembly Location MUR1x0E = Device Code x 8 or 10 Y = Year WW = Work Week G = Pb−Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2013 May, 2013 − Rev. 4 1 Publication Order Number: MUR180E/D MUR180E, MUR1100E THERMAL CHARACTERISTICS Characteristics Maximum Thermal Resistance, Junction−to−Ambient Symbol Value Unit RqJA See Note 3 °C/W Value Unit ELECTRICAL CHARACTERISTICS Characteristics Symbol Maximum Instantaneous Forward Voltage (Note 2) (iF = 1.0 A, TJ = 150°C) (iF = 1.0 A, TJ = 25°C) vF Maximum Instantaneous Reverse Current (Note 2) (Rated dc Voltage, TJ = 100°C) (Rated dc Voltage, TJ = 25°C) iR Maximum Reverse Recovery Time (IF = 1.0 A, di/dt = 50 Amp/ms) (IF = 0.5 A, iR = 1.0 Amp, IREC = 0.25 A) trr Maximum Forward Recovery Time (IF = 1.0 A, di/dt = 100 Amp/ms, Recovery to 1.0 V) tfr 75 ns WAVAL 10 mJ IRM 1.7 A Controlled Avalanche Energy (See Test Circuit in Figure 6) Typical Peak Reverse Recovery Current (IF = 1.0 A, di/dt = 50 A/ms) 1.50 1.75 600 10 100 75 V mA ns 2. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%. ORDERING INFORMATION Device Package MUR180E Axial Lead* MUR180EG Axial Lead* MUR180ERL Axial Lead* MUR180ERLG Axial Lead* MUR1100E Axial Lead* MUR1100EG Axial Lead* MUR1100ERL Axial Lead* MUR1100ERLG Axial Lead* Shipping† 1000 Units / Bag 5000 / Tape & Reel 1000 Units / Bag 5000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *These packages are inherently Pb−Free. http://onsemi.com 2 MUR180E, MUR1100E ELECTRICAL CHARACTERISTICS 1000 IR, REVERSE CURRENT (m A) 20 10 7.0 3.0 TJ = 175°C 25°C 2.0 10 100°C 1.0 25°C 0.1 100°C 0.01 1.0 0 100 200 300 400 500 600 700 800 0.7 VR, REVERSE VOLTAGE (VOLTS) 0.5 Figure 2. Typical Reverse Current* 900 1000 * The curves shown are typical for the highest voltage device in the grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. 0.3 0.2 IF(AV) , AVERAGE FORWARD CURRENT (AMPS) i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 5.0 TJ = 175°C 100 0.1 0.07 0.05 0.03 0.02 0.01 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 5.0 4.0 RATED VR RqJA = 50°C/W 3.0 2.0 dc SQUARE WAVE 1.0 0 0 vF, INSTANTANEOUS VOLTAGE (VOLTS) 50 Figure 1. Typical Forward Voltage 100 150 200 250 TA, AMBIENT TEMPERATURE (°C) 5.0 10 I (CAPACITIVELOAD) PK + 20 I AV 4.0 20 5.0 TJ = 25°C C, CAPACITANCE (pF) PF(AV) , AVERAGE POWER DISSIPATION (WATTS) Figure 3. Current Derating (Mounting Method #3 Per Note 3) 3.0 dc TJ = 175°C 2.0 SQUARE WAVE 1.0 10 7.0 5.0 3.0 2.0 0 0 0.5 1.0 1.5 2.0 2.5 0 10 20 30 40 IF(AV), AVERAGE FORWARD CURRENT (AMPS) VR, REVERSE VOLTAGE (VOLTS) Figure 4. Power Dissipation Figure 5. Typical Capacitance http://onsemi.com 3 50 MUR180E, MUR1100E +VDD IL 40 mH COIL BVDUT VD ID MERCURY SWITCH ID IL DUT S1 VDD t0 t1 Figure 6. Test Circuit ǒ BV 2 DUT W [ 1 LI LPK AVAL 2 BV –V DUT DD t Figure 7. Current−Voltage Waveforms component resistances. Assuming the component resistive elements are small Equation (1) approximates the total energy transferred to the diode. It can be seen from this equation that if the VDD voltage is low compared to the breakdown voltage of the device, the amount of energy contributed by the supply during breakdown is small and the total energy can be assumed to be nearly equal to the energy stored in the coil during the time when S1 was closed, Equation (2). The oscilloscope picture in Figure 8, shows the information obtained for the MUR8100E (similar die construction as the MUR1100E Series) in this test circuit conducting a peak current of one ampere at a breakdown voltage of 1300 V, and using Equation (2) the energy absorbed by the MUR8100E is approximately 20 mjoules. Although it is not recommended to design for this condition, the new “E’’ series provides added protection against those unforeseen transient viruses that can produce unexplained random failures in unfriendly environments. The unclamped inductive switching circuit shown in Figure 6 was used to demonstrate the controlled avalanche capability of the new “E’’ series Ultrafast rectifiers. A mercury switch was used instead of an electronic switch to simulate a noisy environment when the switch was being opened. When S1 is closed at t0 the current in the inductor IL ramps up linearly; and energy is stored in the coil. At t1 the switch is opened and the voltage across the diode under test begins to rise rapidly, due to di/dt effects, when this induced voltage reaches the breakdown voltage of the diode, it is clamped at BVDUT and the diode begins to conduct the full load current which now starts to decay linearly through the diode, and goes to zero at t2. By solving the loop equation at the point in time when S1 is opened; and calculating the energy that is transferred to the diode it can be shown that the total energy transferred is equal to the energy stored in the inductor plus a finite amount of energy from the VDD power supply while the diode is in breakdown (from t1 to t2) minus any losses due to finite EQUATION (1): t2 Ǔ 500V 50mV CH1 CH2 A 20ms 953 V VERT CHANNEL 2: IL 0.5 AMPS/DIV. CHANNEL 1: VDUT 500 VOLTS/DIV. EQUATION (2): 2 W [ 1 LI LPK AVAL 2 1 CH1 ACQUISITIONS SAVEREF SOURCE CH2 217:33 HRS STACK REF REF Figure 8. Current−Voltage Waveforms http://onsemi.com 4 TIME BASE: 20 ms/DIV. MUR180E, MUR1100E NOTE 3 − AMBIENT MOUNTING DATA Data shown for thermal resistance, junction−to−ambient (RqJA) for the mountings shown is to be used as typical guideline values for preliminary engineering or in case the tie point temperature cannot be measured. TYPICAL VALUES FOR RqJA IN STILL AIR Mounting Method 1 2 RqJA Lead Length, L 1/8 1/4 1/2 52 65 72 67 80 87 Units °C/W °C/W 50 °C/W 3 MOUNTING METHOD 1 L L ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ MOUNTING METHOD 2 ÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉ L L Vector Pin Mounting ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ MOUNTING METHOD 3 L = 3/8 ″ Board Ground Plane P.C. Board with 1−1/2 ″ X 1−1/2 ″ Copper Surface http://onsemi.com 5 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS AXIAL LEAD CASE 59−10 ISSUE U DATE 15 FEB 2005 B K STYLE 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO−41 OUTLINE SHALL APPLY 4. POLARITY DENOTED BY CATHODE BAND. 5. LEAD DIAMETER NOT CONTROLLED WITHIN F DIMENSION. D STYLE 2 F A SCALE 1:1 POLARITY INDICATOR OPTIONAL AS NEEDED (SEE STYLES) F K DIM A B D F K INCHES MIN MAX 0.161 0.205 0.079 0.106 0.028 0.034 −−− 0.050 1.000 −−− MILLIMETERS MIN MAX 4.10 5.20 2.00 2.70 0.71 0.86 −−− 1.27 25.40 −−− GENERIC MARKING DIAGRAM* STYLE 1: PIN 1. CATHODE (POLARITY BAND) 2. ANODE STYLE 2: NO POLARITY A xxx xxx YYWW STYLE 1 xxx A YY WW A xxx xxx YYWW STYLE 2 = Specific Device Code = Assembly Location = Year = Work Week *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. DOCUMENT NUMBER: DESCRIPTION: 98ASB42045B AXIAL LEAD Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative