NFZ5BBW7R6LN10L

Reference Only SpecNo.JENF243J-0011A-01 CHIP NOISE FILTER P1/10 NFZ5BBW□□□LN10□ REFERENCE SPECIFICATION 1.Scope This reference specification applies to NFZ5BBW_LN10L Series, Chip Noise Filter. 2.Part Numbering (ex) NF Product ID Z 5B Structure Dimension (L×Ｗ) BW 2R9 Features Impedance L N Performance 1 0 Category Numbers of Circuit L Other Packaging L:Taping 3.Rating Operating Temperature Range.(Ambient temperature; Self-temperature rise is not included) (Product temperature; Self- temperature rise is included) Storage Temperature Range. -40 to +105°C Impedance at 1MHz Customer Part Number -40 to +105°C -40 to +125°C *1 Rated Current(mA) DC MURATA Part Number (Ω) NFZ5BBW2R9LN10L NFZ5BBW2R9LN10K NFZ5BBW4R5LN10L NFZ5BBW4R5LN10K NFZ5BBW6R7LN10L NFZ5BBW6R7LN10K NFZ5BBW7R6LN10L NFZ5BBW7R6LN10K NFZ5BBW100LN10L NFZ5BBW100LN10K NFZ5BBW140LN10L NFZ5BBW140LN10K NFZ5BBW170LN10L NFZ5BBW170LN10K NFZ5BBW220LN10L NFZ5BBW220LN10K NFZ5BBW310LN10L NFZ5BBW310LN10K NFZ5BBW450LN10L NFZ5BBW450LN10K NFZ5BBW520LN10L NFZ5BBW520LN10K NFZ5BBW610LN10L NFZ5BBW610LN10K NFZ5BBW970LN10L NFZ5BBW970LN10K NFZ5BBW141LN10L NFZ5BBW141LN10K Tolerance (%) Resistance (Ω) *2 Ambient temperature 85℃ *3 Ambient temperature 105℃ 2.9 0.012±20% 4000 2050 4.5 0.015±20% 3400 1800 6.7 0.019±20% 3100 1680 0.019±20% 3100 1680 10 0.024±20% 3000 1630 14 0.030±20% 2600 1370 17 0.035±20% 2500 1230 22 0.044±20% 2300 1210 31 0.058±20% 2000 1090 45 0.083±20% 1650 1020 52 0.100±20% 1610 1010 61 0.106±20% 1600 1000 97 0.187±20% 1200 700 140 0.259±20% 1050 600 7.6 ±30 *1: As for the rated current, rated current derated as figure.1 depending on the operating temperature. *2: When applied rated current to the Products, temperature rise caused by self heating will be 40°C or less. *3: When applied rated current to the Products, temperature rise caused by self heating will be 20°C or less. MURATA MFG.CO., LTD Reference Only SpecNo.JENF243J-0011A-01 Rated Current [mA] Fugure. 1 Rated  Current at 85℃ Rated  Current at 105℃ 105 85 Operating Temperature (Ambient temperature)[℃] 4. Testing Conditions 《Unless otherwise specified》 Temperature : Ordinary Temperature (15 to 35°C) Humidity : Ordinary Humidity (25 to 85 %(RH)) 《In case of doubt》 Temperature : 20 ± 2°C Humidity : 60 to 70 %(RH) Atmospheric Pressure : 86 to 106 kPa 5.Appearance and Dimensions ※No Marking ■Unit Mass（Typical value） 0.22ｇ 5.0±0.2 （0.2） 2.0±0.2 5.0±0.2 5.0±0.2 1.5±0.2 1.5±0.2 6.Electrical Performance No. Item 6.1 Impedance Specification Impedance shall meet item 3. Test Method Measuring Equipment : Agilent 4284A or equivalent Measuring Frequency: 1MHz 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter MURATA MFG.CO., LTD P2/10 SpecNo.JENF243J-0011A-01 Reference Only P3/10 7.Mechanical Performance No. 7.1 Item Shear Test Specification Chip Noise Filter shall not be damaged. Test Method Substrate: Glass-epoxy substrate Force: 10N Chip Coil Hold Duration: 5±1s Ｆ Substrate 7.2 Bending Test Substrate: Glass-epoxy substrate (100×40×1.6mm) Speed of Applying Force: 0.5mm / s Deflection: 2mm Hold Duration: 5s Pressure jig R230 F Deflection 45 7.3 Vibration Chip Noise Filter shall not be damaged. 7.4 Solderability The wetting area of the electrode shall be at least 90% covered with new solder coating. 7.5 Resistance to Soldering Heat Appearance: No damage Impedance Change: within ± 10% 45 Product (in mm) Oscillation Frequency : 10 to 2000 to 10Hz for 20 min Total amplitude : 1.5 mm or Acceleration amplitude 98 m/s2 whichever is smaller. Testing Time: A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 hours) Flux: Ethanol solution of rosin,25(wt)% (Immersed for 5s to 10s) Solder : Sn-3.0Ag-0.5Cu Pre-Heating: 150±10°C / 60 to 90s Solder Temperature: 240±5°C Immersion Time: 3±1 s Flux: Ethanol solution of rosin,25(wt)% (Immersed for 5s to 10s) Solder : Sn-3.0Ag-0.5Cu Pre-Heating: 150±10°C / 60 to 90s Solder Temperature: 270±5°C Immersion Time: 10±1 s Then measured after exposure in the room condition for 24±2 hours. MURATA MFG.CO., LTD Reference Only SpecNo.JENF243J-0011A-01 P4/10 8.Environmental Performance (It shall be soldered on the substrate.) No. 8.1 Item Heat Resistance 8.2 Cold Resistance 8.3 Humidity 8.4 Temperature Cycle Specification Appearance: No damage Impedance Change: within ± 10% DC Resistance Change: within ± 10% Test Method Temperature: 105±2°C 48 Time: 1000± 0 hours Then measured after exposure in the room condition for 24±2 hours. Temperature: -40±2°C 48 Time: 1000± 0 hours Then measured after exposure in the room condition for 24±2 hours. Temperature: 40±2°C Humidity: 90~95%(RH) 48 Time: 1000± 0 hours Then measured after exposure in the room condition for 24±2 hours. 1 cycle: 1 step: -40±2°C / 30±3 min 2 step: Ordinary temp. / 10 to 15 min 3 step: +105±2°C / 30±3 min 4 step: Ordinary temp. / 10 to 15 min Total of 10 cycles Then measured after exposure in the room condition for 24±2 hours. +0.1 -0 2.0±0.05 4.0±0.1 5.3±0.1 5.5±0.05 φ 1.5 (0.3) 12.0±0.2 9.1 Appearance and Dimensions of plastic tape 1.75±0.1 9. Specification of Packaging Dimension of the Cavity is measured at the bottom side. 8.0±0.1 *Lead-in/out wire 2.4±0.1 Direction of feed 5.3±0.1 (in mm) 9.2 Specification of Taping (1) Packing quantity (standard quantity) φ180 mm reel : 500 pcs. / reel φ330 mm reel : 3000 pcs. / reel (2) Packing Method Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape. (3) Sprocket hole The sprocket holes are to the right as the tape is pulled toward the user. (4) Spliced point Plastic tape and Cover tape has no spliced point. (5) Missing components number Missing components number within 0.1 % of the number per reel or 1 pc., whichever is greater, and are not continuous. The specified quantity per reel is kept. 9.3 Pull Strength Embossed carrier tape 10N min. Cover tape 5N min. MURATA MFG.CO., LTD Reference Only SpecNo.JENF243J-0011A-01 9.4 Peeling off force of cover tape Speed of Peeling off 165 to 180 degree 300mm/min F P5/10 Cover tape 0.2 to 0.7N Peeling off force (minimum value is typical) Plastic tape 9.5 Dimensions of Leader-tape, Trailer and Reel There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows. « Packaging Code : L (φ180mm reel) » Trailer : 160 min. 2.0±0.5 Leader Label 190 min 210 min Empty tape Cover tape  13.0±0.2  60± 1 0  21.0±0.8 13.0±1 0 Direction of feed 17.0±1.4 (in mm) 0  180± 3 « Packaging Code : K (φ330mm reel) » 2.0±0.5 Trailer 160min. Leader Label 190min. 210min.. Empty Tape Cover tape  13.0±0.2  21.0±0.8 Direction of feed 330±2.0 9.6 Marking for reel Customer part number, MURATA part number, Inspection number(1) , RoHS marking (2), Quantity etc ･･･ 1) « Expression of Inspection No. » □□ OOOO (1) (1) Factory Code (2) Date (2)  (3) First digit : Year / Last digit of year Second digit : Month / Jan. to Sep.  1 to 9, Oct. to Dec.  O, N, D Third, Fourth digit : Day (3) Serial No. 2) « Expression of RoHS marking » ROHS – Y (△) (1) (2) (1) RoHS regulation conformity parts. (2) MURATA classification number 9.7 Marking for Outside package (corrugated paper box) Customer name, Purchasing order number, Customer part number, MURATA part number, RoHS marking (2) ,Quantity, etc ･･･ MURATA MFG.CO., LTD Reference Only SpecNo.JENF243J-0011A-01 P6/10 9.8. Specification of Outer Case Label Reel H φ180mm φ330mm D W 10. Outer Case Dimensions (mm) W D H 186 186 93 340 340 95 Standard Reel Quantity in Outer Case (Reel) 4 4 Above Outer Case size is typical. It depends on a quantity of an order. Caution Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1) Aircraft equipment (7) Traffic signal equipment (2) Aerospace equipment (8) Disaster prevention / crime prevention equipment (3) Undersea equipment (9) Data-processing equipment (4) Power plant control equipment (10) Applications of similar complexity and /or reliability requirements (5) Medical equipment to the applications listed in the above (6) Transportation equipment (vehicles, trains, ships, etc.) 11. Notice This product is designed for solder mounting. Please consult us in advance for applying other mounting method such as conductive adhesive. 11.1 Land pattern designing Recommended land pattern for flow and reflow soldering is as follows: It has been designed for Electric characteristics and solderability. Please follow the recommended patterns. Otherwise, their performance which includes electrical performance or solderability may be affected, or result to "position shift" in soldering process. (Land pattern for Reflow soldering) (Land pattern for Flow soldering) 1.2[mm] Land Chip Colil 5.5 Product outline Solder Resist Land outline 4.1 Orifice of solder resist 2.0[mm] 2.7[mm] 1.8 1.85 (in mm) 7.4[mm] 11.2 Flux, Solder ・Use rosin-based flux. ・Don’t use highly acidic flux with halide content exceeding 0.2(wt)% (chlorine conversion value). ・Don’t use water-soluble flux. ・Use Sn-3.0Ag-0.5Cu solder Solder ・Standard thickness of solder paste : 100μm to 150μm Other flux (except above) Please contact us for details, then use. Flux MURATA MFG.CO., LTD SpecNo.JENF243J-0011A-01 Reference Only P7/10 11.3 Flow soldering conditions / Reflow soldering conditions  Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to 100°C max. Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max. Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality. Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the deterioration of product quality. (1)Flow soldering profile Temp. (℃) 265℃±3℃ 250℃ Limit Profile 150 Heating Time 60s min. Pre-heating Heating Cycle of flow Standard Profile Time. (s) Standard Profile Limit Profile 150℃、60s min. 250℃、4s～6s 265℃±3℃、5s 2 times 1 time (2)Reflow soldering profile Temp. 260℃ 245℃±3℃ 220℃ (℃) 230℃ Limit Profile 180 150 Standard Profile 30s～60s 60s max 90s±30s Pre-heating Heating Peak temperature Cycle of reflow Time(s) Standard Profile Limit Profile 150～180°C 、90s±30s above 220°C、30s～60s above 230°C、60s max. 245±3°C 260°C,10s 2 times 2 times MURATA MFG.CO., LTD Reference Only SpecNo.JENF243J-0011A-01 P8/10 11.4 Reworking with soldering iron. The following conditions must be strictly followed when using a soldering iron. Pre-heating 150°C,1 min Tip temperature 380°C max. Soldering iron output 80W max. Tip diameter φ3mm max. Soldering time 3 (+1,-0)s Times 2 times Note :Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the products due to the thermal shock. 11.5 Solder Volume ・Adhesive application of flow is recommended the 3-point application.（prevent the drop of products） Adhesive application position ・Amount of adhesive applied is a standard 1/2 to 2/3 of the bottom flange thickness. The bottom flange 11.6 Product's location The following shall be considered when designing and laying out P.C.B.’s. (1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board. ［Products direction］ Electrode Products shall be located in the sideways direction (Length:ab) to the mechanical stress. Poor example） Electrode (Good example) (2) Products location on P.C.B. separation Products (A,B,C,D) shall be located carefully so that products are not subject to the mechanical stress due to warping the board. Because they may be subjected the mechanical stress in order of ACB  D. Electrode Seam A Electrode MURATA MFG.CO., LTD C B Slit Reference Only SpecNo.JENF243J-0011A-01 P9/10 11.7 Cleaning Conditions Products shall be cleaned on the following conditions. (1) Cleaning temperature shall be limited to 60°C max.(40°C max for IPA.) (2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance phenomenon at the mounted products and P.C.B. Power : 20 W / l max. Frequency : 28kHz to 40kHz Time : 5 minutes max. (3) Cleaner 1. Alternative cleaner Isopropyl alcohol (IPA) 2. Aqueous agent  PINE ALPHA ST-100S (4) There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in order to remove the cleaner. (5) Other cleaning Please contact us. 11.8 Resin coating The impedance value may change due to high cure-stress of resin to be used for coating/molding products. An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some operating condition may cause corrosion of wire, leading to open circuit. So, please pay your careful attention when you select resin in case of coating/molding the products with the resin.Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products mounted on your board. 11.9 Caution for use  Sharp material such as a pair of tweezers or other material such as bristles of cleaning brush, shall not be touched to the winding portion to prevent the breaking of wire.  Mechanical shock should not be applied to the products mounted on the board to prevent the breaking of the core. 11.10 Handling of a substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the product. Bending Twisting 11.11 Storage and Handling Requirements (1) Storage period Use the products within 12 months after delivered. Solderability should be checked if this period is exceeded. (2) Storage conditions  Products should be stored in the warehouse on the following conditions. Temperature : -10 ~ 40°C Humidity : 15 to 85% relative humidity No rapid change on temperature and humidity The electrode of the products is coated with solder. Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability.  Products should not be stored on bulk packaging condition to prevent the chipping of the core and the breaking of winding wire caused by the collision between the products.  Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.  Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. (3) Handling Condition Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. MURATA MFG.CO., LTD SpecNo.JENF243J-0011A-01 12. Reference Only P10/10 Note (1)Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2)You are requested not to use our product deviating from the reference specifications. (3)The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG.CO., LTD