NM485D6S5MC
www.murata.com
Isolated RS485 Driver DC-DC
6V
5V
Regulator
6V
Isolated DC-DC Power Supply
0V
5V regulated
0V
0V
-6V
-6V
Isolation
Vcc
0V
FEATURES
Patent pending
3.3V
Regulator
Isolated 485 Transceiver
input lines
output lines
input lines
output lines
ANSI/AAMI ES60601-1, 2 MOOP/1 MOPP
recognised
SELECTION GUIDE
UL60950 recognised for 250Vrms reinforced
insulation
Order Code1
SMD compatible
MODULE CHARACTERISTICS
+6V, -6V unregulated and +5V regulated
isolated outputs
DRIVER
Parameter
Test conditions
Min.
Differential driver and receiver
Differential Output
Voltages
Short Circuit Output
Current
Complementary
Output States
Common-mode
Output Voltages
Complementary
Output States
Loaded RL = 100Ω (RS-422), See Figure 1
Loaded RL = 54Ω (RS-485)
2.0
1.5
500kbps data rate
Complies with ANSI TIA/EIA RS-485-A-1998
and ISO 8482: 1987(E)
Industrial temperature range -40°C to
+85°C
Tested at 3000Vac rms ‘Hi Pot Test’
NM485D6S5MC
Max.
Units
Symbol
3.6
3.6
V
VOD
250
mA
IOS
RL = 54Ω or 100Ω, see figure 1
0.2
V
Δ |VOD|
RL = 54Ω or 100Ω, see figure 1
3.0
V
VOC
PRODUCT OVERVIEW
Input Threshold High
The NM485D6S5MC is a low power electrically
isolated differential driver and receiver designed
for bi-directional data communication or multipoint
bus transmission. The device combines a tri-state
differential line driver and a differential input line
receiver. The driver and receiver have active high
and active low enables, respectively, which can be
connected together to function as direction control.
No external components are needed as a single
5V supply powers all functions either side of the
isolation boundary. NM485D655MC also provides
a regulated 5V, unregulated 6V and -6V isolated
supply’s for system use.
Input Current
Typ.
0.2
V
Δ |VOC|
V
VIL
0.7 x VCC
V
VIH
+0.01
+10
μA
II
RL = 54Ω or 100Ω, see figure 1
0.25 x
Vcc
Input Threshold Low
-10
2
RECEIVER
Parameter
Differential Input
Threshold Voltages
Input Voltages
Hysteresis
Input Current (A, B)
Line Input Resistance
Tristate Leakage
Current
Output Voltage Low
Test conditions
Min.
Typ.
Max.
Units
Symbol
-7V < VCM < +12V
-200
-125
-30
mV
VTH
VOC = 0V
-7V < VCM < +12V
15
-100
96
Vcc 0.3
Output Voltage High
Short-Circuit Current
Common-Mode
Transient Immunity
For full details go to
https://www.murata.com/englobal/products/power/rohs
5V
VCM = 1 kV, transient magnitude = 800V
0.2
Vcc 0.2
mV
VHYS
+125
μA
kΩ
II
RIN
±1
μA
IOZR
0.4
V
VOLRxD
V
VOHRxD
100
mA
25
KV/μS
1. Components are supplied in tape and reel packaging, please refer to tape and reel specification section. Orderable part numbers are
NM485D6S5MC-R7 (80 pieces per reel), or NM485D6S5MC-R13 (350 pieces per reel).
2. VCM is the common-mode potential difference between the logic and bus sides. The transient magnitude is the range over which the
common mode is slewed. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.
www.murata.com
KDC_NM485D6S5MC.D01 Page 1 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
TIMING SPECIFICATIONS
Parameter
Driver
Test conditions
Min.
Propagation Delay
Differential Driver Output Skew
Rise Time/Fall Time
Enable Time
Disable Time
RL = 54Ω, CL1 = CL2 = 100 pF see figure 2 & 6
RL = 54Ω, CL1 = CL2 = 100 pF see figure 2 & 6
RL = 54Ω, CL1 = CL2 = 100 pF see figure 2 & 6
RL = 110Ω, CL1 = 50 pF see figure 4 & 7
RL = 110Ω, CL1 = 50 pF see figure 4 & 7
250
200
Typ.
Max.
Units
Symbol
450
700
100
1100
1.5
200
ns
ns
ns
μs
ns
tDPLH, tDPHL
TDSKEW
TDR, TDF
TZL, TZH
TLZ, THZ
200
30
13
13
ns
ns
ns
ns
TPLH, TTPHL
TPWD
TZL, TZH
TLZ, THZ
Receiver
Propagation Delay
Pulse Width Distortion
Enable Time
Disable Time
CL1 = 15 pF see figure 3 & 8
CL1 = 15 pF see figure 3 & 8
RL = 1kΩ, CL1 = 15 pF see figure 5 & 9
RL = 1kΩ, CL1 = 15 pF see figure 5 & 9
ABSOLUTE MAXIMUM RATINGS
Supply voltage VCC with respect to pin 11
Bus Terminal Voltages
Logic Terminal Voltage
Data transmission rate
6V
-9V to +14V
-0.5V to Vcc +0.5V
500Kbps
www.murata.com
KDC_NM485D6S5MC.D01 Page 2 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
FIGURE 1
FIGURE 2
FIGURE 3
DRIVER TEST CIRCUIT
DRIVER TEST CIRCUIT
RECEIVER TEST CIRCUIT
(For output voltage levels)
(For timing characteristics)
(For timing characteristics)
A
RL
2
CL1
Y
VOD
vout
RL
CL
B
Z
RL
CL2
2
FIGURE 4
FIGURE 5
FIGURE 6
DATA ENABLE TEST CIRCUIT
READ ENABLE TEST CIRCUIT
DRIVER TIMING
(For signal propagation)
VDD1
VDD1/2
VDD1/2
+1.5v
VOUT
VCC
VCC
0V
S1
Y
RL
0V or 3V
S1
Z
tDPLH
tDPLH
-1.5v
RL
S2
RE
S2
Z
CL
vout
CL
1/2VO
VO
DE
Y
RE IN
+VO
90% POINT
VDIFF=V(Y)-V(Z)
90% POINT
VDIFF
10% POINT
-VO
10% POINT
tDR
FIGURE 7
DATA ENABLE TIMING SPECIFICATION
tDF
FIGURE 8
FIGURE 9
RECEIVER TIMING
READ ENABLE TIMING SPECIFICATION
vDD1
vDD1
RE
DE
0.5VDD1
0V
tZL
Y, Z
0.5VDD1
0.5VDD1
0.5VDD1
A, B
0V
0V
0V
tPLH
tPHL
tZL
tLZ
tLZ
RxD
1.5V
VOH
2.3V
VOL +0.5V
RXD
VOL
1.5V
VOL +0.5V
tZH
tZH
VOH -0.5V
Y, Z
tHZ
VOL
tHZ
VOH
VOL
1.5V
VOH -0.5V
RxD
VOH
1.5V
2.3V
0V
0V
0V
www.murata.com
KDC_NM485D6S5MC.D01 Page 3 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
DC-DC CHARACTERISTICS
INPUT CHARACTERISTICS
Parameter
Test conditions
Min.
Typ.
Max.
Units
Voltage range
Input reflected ripple current
Continuous operation
5V Input
4.5
5
6
5.5
V
mA pk-pk
Test conditions
Min.
Typ.
Max.
Units
5V Output regulated (0mA to 80mA)
+6V Unregulated (16mA to 160mA)
-6V Unregulated (16mA to 160mA)
4.92
5.4
-6.6
5
6
-6
1.1
5
25
5.08
6.6
-5.4
1.2
8
50
0.4
0.8
OUTPUT CHARACTERISTICS
Parameter
Output voltage spec
(The maximum current share across all outputs is 160mA.)
Line regulation
Load regulation
Ripple and noise
Power
5V Regulated
Total available power across all outputs
V
%%
%
mV
W
TEMPERATURE CHARACTERISTICS
Parameter
Test conditions
Min.
Operation
Storage
Product temperature rise above ambient
See derating graph
-40
-50
Measured in the isolation barrier
Typ.
Max.
20
85
125
30
Typ.
Max.
Units
o
C
ISOLATION CHARACTERISTICS
Parameter
Test conditions
Min.
Isolation test voltage
Production tested for 1 Second
Qualification tested for 1 minute
3000
3000
Isolation capacitance
Resistance
5
Viso = 1kVDC
Units
VACrms
VACrms
pF
GΩ
10
GENERAL CHARACTERISTICS
Parameter
Test conditions
MTTF - nominal input voltage at full load
MIL-HDBK-217 FN2
Telcordia SR-332
Switching frequency
Min.
Typ.
800
10000
95
Max.
Units
kHrs
kHrs
kHz
www.murata.com
KDC_NM485D6S5MC.D01 Page 4 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NM485D6S5MC is 100% production tested at 3kVAC rms for 1 second and have been qualification tested at 3kVAC rms for 1 minute.
The NM485D6S5MC has been recognised by Underwriters Laboratory to 250Vrms reinforced insulation.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NM485D6S5MC has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enamelled wire.
While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel
(typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited.
We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This
consideration equally applies to agency recognised parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation
system of physical spacing or barriers.
SAFETY APPROVAL
ANSI/AAMI ES60601-1
The NM485D6S5MC has been recognised to ANSI/AAMI ES60601-1 and provides 1 MOPP (Means Of Patient Protection) and 2 MOOP (Means Of Operator Protection) based upon a
working voltage of 250Vrms max, between Primary and Secondary.
UL 60950
The NM485D6S5MC has been recognised by Underwriters Laboratory (UL) to UL 60950 for reinforced insulation to a working voltage of 250Vrms.
Creepage is 5mm and clearance is 4mm.
FUSING
The NM485D6S5MC is not internally fused so to meet the requirements of UL an anti-surge input line fuse should always be used with ratings as defined below.
NM485D6S5MC - 1A
All fuses should be UL recognised and rated to at least the maximum allowable DC input voltage.
RoHS COMPLIANCE, MSL AND PSL INFORMATION
The NM485D6S5MC is compatible with Pb-Free soldering systems and is also backward compatible with Sn/Pb soldering
systems. The NM485D6S5MC has a process, moisture, and reflow sensitivity classification of MSL2 PSL R7F as defined in
J-STD-020 and J-STD-075. This translates to: MSL2 = 1 year floor life, PSL R7F = Peak reflow temperature 245°C with
a limitation on the time above liquidus (217°C) which for this series is 90sec max. Please refer to application notes for
further information. The pin termination finish on this product series is Gold with Nickel Pre-plate.
www.murata.com
KDC_NM485D6S5MC.D01 Page 5 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
APPLICATION NOTES
The increased use of balanced data transmission lines, (distributing data to several system components and peripherals over relatively long lines) has brought about the need for
multiple driver/receiver combinations on a single twisted pair line. This resulted in an upgraded version of EIA RS-422, named EIA-485. EIA-485 takes into account EIA RS-422
requirements for balanced line data transmission, and allows for multiple drivers and receivers.
The NM485D6S5MC is a low power isolated differential interface providing EIA-485 compatibility. The use of a differential communications interface such as the NM485D6S5MC
allows data transmission at high rates and over long distances to be accomplished. This is because effects of external noise sources and cross talk are much less pronounced
on the data signal. Any external noise source coupling onto the differential lines will appear as an extra common mode voltage which the receiver is insensitive to. The difference
between the signal levels on the two lines will therefore remain the same. Similarly a change in the local ground potential at one end of the line will appear as just another change
in the common mode voltage level of the signals. Twisted pair cable is commonly used for differential communications since its twisted nature tends to cause cancellation of the
magnetic fields generated by the current flowing through each wire, thus reducing the effective inductance of the pair.
Computer and industrial serial interfacing are areas where noise can seriously affect the integrity of data transfer, and a proven route to improve noise performance for any interface system is galvanic isolation. Galvanic isolation removes the ground loop currents from data lines and hence the impressed noise voltage which affects the signal is also eliminated. The isolation feature of the NM485D6S5MC also means that common mode noise effects are removed and many forms of radiated noise are reduced to negligible limits.
NM485
Truth table for NM485 functionality
DE
RE
RXD
Y
Z
5Vin
0V
O
O
≈A
Hi Z
Hi Z
O
I
Hi Z
Hi Z
Hi Z
I
O
≈A
≈Txd
≈Txd
I
I
Hi Z
≈Txd
≈Txd
+5V
Isolated
Power
supply
+6V
-6V
0V
A
RxD
R
B
RE
DE
Z
TxD
D
Y
Hi Z = High impedance tri state
Figure 10 demonstrates how the differential lines of the NM485D6S5MC can be connected to form a transceiver. Data direction is controlled by the driver enable and receiver
enable pins. This means the device can receive when the receiver enable is low and transmit when the driver enable is high. As the driver is active high, to reduce the power dissipation even further, it is advisable to disable the driver when not transmitting data.
Configuring the NM485D6S5MC as a transceiver
The NM485D6S5MC is configured as a transceiver simply by connecting B to Z, A to Y and D ENABLE to R ENABLE. The system then writes data to the bus when XEN1 is
high ( with read disabled) and reads data from bus when XEN1 is low ( with write disabled).
FIGURE 10
MC68195
NM485D6S5MC
+5Vin
1 VCC
RDATA1 28
A
11
B
10
3 RxD
XEN1 27
5 D ENABLE
XDATA1 25
6 TxD
4 R ENABLE
2 GND
OV
Z
8
7
Y
ISO GND 12
Isolation Barrier
Minimum load
The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%.
www.murata.com
KDC_NM485D6S5MC.D01 Page 6 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
APPLICATION NOTES (Continued)
Short Circuit Performance
The NM485D6S5MC offers short circuit protection at low ambient temperatures from -40°C to the temperatures shown in the below graph, when the output power lines
are shorted together or to GND.
For datalines the device has current-limiting and thermal shutdown features to protect against output short circuits and situations where bus contention causes excessive
power dissipation.
1000
Time (seconds)
100
Nominal Vin
High Vin
10
1
25
35
45
55
65
75
85
dĞŵƉĞƌĂƚƵƌĞ;ȗͿ
Capacitive Loading & Start Up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The
product series will start into a capacitance of 47μF with an increased start time of 4.6ms
Typical Start-Up Wave Form
NM485D6S5MC
Start-up time
ms
1.6
www.murata.com
KDC_NM485D6S5MC.D01 Page 7 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
APPLICATION NOTES (Continued)
Typical applications
Figure 11 and Figure 12 show typical applications of half-duplex and full-duplex RS-485 network configurations. Up to 256 transceivers can be connected to the RS-485
bus. To minimize reflections, the line must be terminated at the receiving end in its characteristic impedance and stub lengths off the main line must be kept as short as
possible. For half-duplex operation, this means that both ends of the line must be terminated as either end can be the receiving end. The NM485D6S5MC series offers a
triple supply (+5V, +6V, -6V) which can be used to power system circuitry.
NM485
NM485
5Vin
Isolated
Power
supply
0V
+5V
+5V
+6V
+6V
-6V
-6V
0V
0V
0V
A
A
R
RxD
5Vin
Isolated
Power
supply
R
B
B
RxD
RE
RE
RT
RT
DE
DE
RxD
RE
DE
5Vin
D
R
0V
5Vin
NM485
0V
-6V
Y
Z
A
B
Isolated
Power
supply
B
TxD
TxD
D
Y
Z
D
R
RxD
0V
A
+6V
Y
+5V
Z
Y
0V
-6V
+6V
Z
Isolated
Power
supply
+5V
D
NM485
TxD
RE
DE
TxD
Figure 11. Typical Half-Duplex RS-485 Network
NM485
5Vin
0V
NM485
Isolated
Power
supply
+5V
+5V
+6V
+6V
-6V
-6V
0V
0V
R
B
RT
Z
D
0V
TxD
DE
RE
DE
RE
Z
D
B
RT
RE
DE
TxD
-6V
0V
+6V
Isolated
Power
supply
D
0V
RxD
Y
Z
R
+5V
B
5Vin
A
NM485
-6V
0V
Isolated
Power
supply
0V
5Vin
NM485
+6V
Y
+5V
TxD
5Vin
Y
A
RxD
Isolated
Power
supply
A
B
A
Z
R
RxD
R
RxD
Y
D
RE
DE
TxD
Figure 12. Typical Full-Duplex RS-485 Network
www.murata.com
KDC_NM485D6S5MC.D01 Page 8 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
Load (%)
DERATING GRAPHS
NM485D6S5MC
100
90
80
70
60
50
40 Figure 11. Typical Full-Duplex RS-485 Network
30
20
10
0
25
35
45
55
65
75
Temperature (°C)
Still Air
85
EFFICIENCY VS LOAD GRAPH
NM485D6S5MC
70
60
Efficiency (%)
50
40
30
20
10
0
0
10
20
30
40
50
60
70
80
90
100
Load (%)
TOLERANCE ENVELOPE
The voltage tolerance envelope show typical load regulation characteristics for the NM485D6S5MC. The tolerance envelope is the maximum output voltage variation due to changes in output loading and set
point accuracy.
NM485D6S5MC
9%
Output Voltage
6%
2%
-3%
10
25
50
75
100
Output Load Current (%)
www.murata.com
KDC_NM485D6S5MC.D01 Page 9 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
EMC FILTERING AND SPECTRA
FILTERING
The following filter circuit and table shows the input capacitor and input inductor typically required to meet EN55022 Curve A and B, Quasi-Peak EMC limit, as shown in
the following plot. The following plot shows positive and negative quasi peak and CISPR22 Average Limit A (pink line) and CISPR22 Average Limit B (blue line) adherence
limits.
L1
ISOLATOR
C2
C1 63V Polycarbonate capacitor
C1
R1
485
Part Number
NM485D6S5MC
L1
22μH
Inductor
Murata Part Number
23220C
Capacitor
C1
2.2μF
NM485D6S5MC
80
70
60
dBuV
50
40
30
20
10
0
1.00E+05
1.00E+06
1.00E+07
1.00E+08
Frequency (Hz)
www.murata.com
KDC_NM485D6S5MC.D01 Page 10 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
PACKAGE SPECIFICATIONS
MECHANICAL DIMENSIONS
PIN CONNECTIONS
Pin
Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
5VIN
GND
RXD
RE
DE
TXD
Y
Z
-6V
B
A
GND
+6V
5V REG
RECOMMENDED FOOTPRINT DETAILS
9.27 [0.365]
10.92 [0.430]
7.62 [0.300]
1.65 [0.065]
x14 PLACES
1.91 [0.075]
4.95 [0.195]
6.60 [0.260]
12.57 [0.495]
3.30 [0.130]
RECOMMENDED
ISOLATION BARRIER
0.89 [0.035]
x14 PLACES
1.37 [0.054]
4.00 [0.157]
4.00 [0.157]
15.87 [0.625]
All dimensions in mm (inches), Controlling dimensions is mm.
All dimensions in mm (inches), Controlling dimensions is mm.
Component layout is shown for reference only.
Weight: 2.88g
www.murata.com
KDC_NM485D6S5MC.D01 Page 11 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
TAPE & REEL SPECIFICATIONS
REEL OUTLINE DIMENSIONS
REEL PACKAGING DETAILS
Ø330 [13.000]
OR
Ø178 [7.000]
Ø 13.5
12.5
0.531
[Ø 0.492
]
LEADER SECTION
400 [15.748] MIN
38.4 [1.512] MAX #
100 [3.937]
MIN
1.5 [0.059]
MIN ##
GOODS
ENCLOSURE
SECTION
TRAILER SECTION
160 [6.299] MIN
Ø20.2 [Ø0.795]
MIN
Carrier tape pockets shown are
illustrative only - Refer to carrier tape
diagram for actual pocket details.
Tape & Reel specifications shall conform with current EIA-481 standard
Unless otherwise stated all dimensions in mm(inches)
Controlling dimension is mm
# Measured at hub
## Six equi-spaced slots on 180mm/7” reel
Reel Quantity: 7” - 80 or 13” - 350
TAPE OUTLINE DIMENSIONS
Ø2.0 [Ø0.079] MIN
2.0 [0.079]
4.0 [0.157]
Ø1.5 +0.1
-0.0
-0.000 ]
[Ø0.059 +0.004
19.5 [0.769]#
14.2 [0.56]
28.4 [1.118]
32.0±0.3 [1 .260±0.012]
3° MAX
1.75 [0.069]
COVER TAPE
15.0 [0.592]#
0.5 [0.020]
Tape & Reel specifications shall conform with current EIA-481 standard
Unless otherwise stated all dimensions in mm(inches) ±0.1mm (±0.004 Inches)
Controlling dimension is mm
Components shall be orientated within the carrier tape as indicated
# Measured on a plane 0.3mm above the bottom pocket
24.0 [0.945]
0.2±0.05 [0 .008±0.002]
8.2 [0.323]
3° MAX
DIRECTION OF UNREELING
www.murata.com
KDC_NM485D6S5MC.D01 Page 12 of 13
NM485D6S5MC
Isolated RS485 Driver DC-DC
DISCLAIMER
Unless otherwise stated in the datasheet, all products are designed for standard commercial and industrial applications and NOT for safety-critical and/or life-critical
applications.
Particularly for safety-critical and/or life-critical applications, i.e. applications that may directly endanger or cause the loss of life, inflict bodily harm and/or loss or severe
damage to equipment/property, and severely harm the environment, a prior explicit written approval from Murata is strictly required. Any use of Murata standard products for any safety-critical, life-critical or any related applications without any prior explicit written approval from Murata shall be deemed unauthorised use.
These applications include but are not limited to:
•
Aircraft equipment
•
Aerospace equipment
•
Undersea equipment
•
Power plant control equipment
•
Medical equipment
•
Transportation equipment ( automobiles, trains, ships, etc.)
•
Traffic signal equipment
•
Disaster prevention / crime prevention equipment
•
Data Processing equipment
Murata makes no express or implied warranty, representation, or guarantee of suitability, fitness for any particular use/purpose and/or compatibility with any application or device of the buyer, nor does Murata assume any liability whatsoever arising out of unauthorised use of any Murata product for the application of the buyer. The
suitability, fitness for any particular use/purpose and/or compatibility of Murata product with any application or device of the buyer remain to be the responsibility and
liability of the buyer.
Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards that anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm, and take appropriate remedial actions. Buyer will fully indemnify and hold
Murata, its affiliated companies, and its representatives harmless against any damages arising out of unauthorised use of any Murata products in any safety-critical and/
or life-critical applications.
Remark: Murata in this section refers to Murata Manufacturing Company and its affiliated companies worldwide including, but not limited to, Murata Power Solutions.
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to: https://www.murata.com/en-eu/products/power/requirements
Murata Power Solutions (Milton Keynes) Ltd. makes no representation that the use of its products in the circuits described herein, or the use
of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do
not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change
without notice.
© 2022 Murata Power Solutions (Milton Keynes) Ltd.
www.murata.com
KDC_NM485D6S5MC.D01 Page 13 of 13
工商网监
湘ICP备2023018690号
