Reference Only
Spec No. JEFL243B-9101G-01
P1/10
SMD type common-mode choke coil
PLT10HH□□□□□□PN□
Murata Standard Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to SMD type common-mode choke coil PLT10H Series for Automotive Electronics
based on AEC-Q200.
2. Part Numbering
(Ex.) PLT
Product ID
10H
H
102
Type Application Common Mode
Impedance Zc
H:Automotive
6R0
Rated
Current
P
Winding
Mode
N
Dimenssion
L
Packaging
code
L:Taping (Φ178mm reel)
K:Taping (Φ330mm reel)
B :Bulk
3. Rating
Customer
Part Number
MURATA
Part Number
PLT10HH1026R0PNL
PLT10HH1026R0PNK
PLT10HH1026R0PNB
PLT10HH9016R0PNL
PLT10HH9016R0PNK
PLT10HH9016R0PNB
PLT10HH501100PNL
PLT10HH501100PNK
PLT10HH501100PNB
PLT10HH401100PNL
PLT10HH401100PNK
PLT10HH401100PNB
PLT10HH101150PNL
PLT10HH101150PNK
PLT10HH101150PNB
PLT10HH450180PNL
PLT10HH450180PNK
PLT10HH450180PNB
Common
Mode Impedance
Zc (at10MHz)
(Ω) Typ.
*
DC
Insulation
Rated Withstand
Inductance ESD Rank
Resistance Resistance
Rated
6:≧25kV
Voltage Voltage
(L)
(Rdc)
(I.R.)
(AD)
V(DC) V(DC) Current
(μH min.)
(mΩ)
(MΩ min.)
(A)
1000
100
250
6
8.0±0.5
10
20
900
100
250
6
8.0±0.5
10
14
500
100
250
10
3.6±0.5
10
9
6
400
100
250
10
3.6±0.5
10
6
100
300
750
15
1.8±0.5
10
2
45
300
750
18
1.3±0.5
10
0.8
・Operating Temperature range (Product temperature; Self- temperature rise is included)
:-55℃~+125℃ (PLT10HH9016R0 / PLT10HH401100/ PLT10HH101150/ PLT10HH450180)
:-55℃~+105℃ (PLT10HH1026R0 / PLT10HH501100)
・Storage Temperature range:-55℃~+125℃
■* Rated Current is derated as below figure depending on the operating temperature.
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P2/10
Standard Testing Conditions
< Unless otherwise specified >
Temperature: Ordinary Temp.15 ºC to 35 °C
Humidity: Ordinary Humidity 25 %(RH) to 85 %(RH)
< In case of doubt >
Temperature: 20 °C ± 2 °C
Humidity: 60 %(RH) to 70 %(RH)
Atmospheric pressure: 86 kPa to 106 kPa
4. Dimenssion
①
②
■Equivalent Circuit
102
④
③
No p o l a rity
③
12.9±0.2
6.6±0.2
2.0±0.3
9.4 max
②
9.1±0.2
④
①
■Unit Mass (Typical value)
2.1±0.3
13.4 max
2.1±0.3
2.1g
1.0±0.2
:Electrode
1.0±0.2
(in mm)
3.2±0.3
5. Marking
(1)Manufacturer Identification:(
)
(2)Parts Number:Common Mode Impedance Zc
PLT10HH1026R0PN□:( 102 )
PLT10HH9016R0PN□:( 901 )
PLT10HH501100PN□:( 501 )
PLT10HH401100PN□:( 401 )
PLT10HH101150PN□:( 101 )
PLT10HH450180PN□:( 450 )
Common Mode Impedance Zc (3 digits)
Manufacturer Identification
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P3/10
6. Electrical Performance
No.
6.1
6.2
Item
Specification
Common
Meet item 3
Mode
Impedance
(Zc) Typ.
Withstand Products shall not be damaged.
Voltage
6.3
Insulation
Meet item 3
Resistance
(I.R.)
6.4
DC
Meet item 3
Resistance
(Rdc)
Inductance Meet item 3
(L)
6.5
Test method
Measuring Frequency: 10MHz
(ref.item 8)
Measuring Equipment: KEYSIGHT 4294A or the equivalent
Use a cable / connector of 50Ω impedance.
Voltage: Rated Voltage×250%
(ref.item 8)
Time:1~5s
Measuring current: 10mA max.
Voltage: Rated Voltage
(ref.item 8)
Time: 30s max.
Measuring current: 10mA max
Measuring Equipment: KEYSIGHT 4339A or the equivalent
Measuring method: four-terminal method
(ref.item 8)
Measuring Frequency:1±0.1kHz
(ref.item 8)
Voltage: 1V (rms) max.
Measuring Equipment: KEYSIGHT 4284A or the equivalent
7.Q200 Requirement
7-1. Performance (based on Table 13 for Ferrite EMI SUPPRESSORS/FILTERS)
AEC-Q200 Rev.D issued June 1. 2010
AEC-Q200
No.
Stress
3 High Temperature
Exposure
4 Temperature Cycling
5 Destructive
Physical Analysis
7 Biased Humidity
8 Operational Life
9 External Visual
10 Physical Dimension
12 Resistance to Solvents
13 Mechanical Shock
Murata Specification / Deviation
Test Method
Meet Table A after testing.
1000hours at Maximum
Table A
Operating Temperature Set
for 24hours at room
Appearance
No damage
temperature, then measured.
Inductance
change
within ±15%
(%∆L)
Insulation
Resistance
Meet item 3
(I.R.)
Withstand
Products shall not
Voltage
be damaged.
Meet Table A after testing.
1000cycles
-55 deg C to + Maximum
Operating Temperature
Set for 24hours at room
temperature, then measured.
Per EIA469
Not Applicable
No electrical tests
1000hours at 85 deg C,
85%RH
Apply max rated voltage.
Meet Table A after testing.
(ref.item 8.2)
Meet Table A after testing.
Apply Maximum Operating
Apply rated voltage.
Temperature 1000hours
Set for 24hours at room
temperature, then measured.
Visual inspection
No abnormalities
Meet ITEM 4
(Style and Dimensions)
Per MIL-STD-202 Method
215
Per MIL-STD-202 Method
213
Condition F:
1500g’s(14.7N)/0.5ms/
Half sine
No defects
Not Applicable
Meet Table A after testing.
MURATA MFG.CO.,LTD
(ref.item 8.2)
Reference Only
Spec No. JEFL243B-9101G-01
P4/10
AEC-Q200
No.
Stress
14 Vibration
Murata Specification / Deviation
Test Method
Meet Table A after testing.
17 ESD
5g's(0.049N) for 20 minutes,
12cycles each of 3 oritentations
Test from 10-2000Hz.
12cycles each of 3 orientations
No-heating
Solder temperature
260C+/-5 deg C
Immersion time 10s
Per AEC-Q200-002
18 Solderbility
Per J-STD-002
19 Electrical
Characterization
20 Flammability
Measured : Inductance
Method b : Not Applicable
95% of the terminations is to be soldered.(except partly-exposed wire)
Flux:Ethanol solution of rosin,25(wt)% includes activator equivalent to
0.06 to 0.10(wt)% chlorine
Refer to 3.Rating.
Per UL-94
Not Applicable
21 Board Flex
Epoxy-PCB(1.6mm)
Deflection 2mm(min)
60 sec minimum holding time
Per AEC-Q200-006
A force of 17.7N for 60sec
Per ISO-7637-2
Meet Table A after testing.
15 Resistance
to Soldering Heat
22 Terminal Strength
30 Electrical Transient
Conduction
Pre-heating:150 to 180C / 90±30s
Meet Table A after testing.
Meet Table A after testing.
ESD Rank: Refer to Item 3. Rating.
No defects
Not Applicable
8. Measuring Terminal
(When measuring and supplying the voltage, the following terminal is applied.)
No.
8.1
8.2
8.3
Item
Measuring terminal
Inductance (L)
DC Resistance (Rdc)
I N
Withstand voltage
Insulation Resistance (I.R.)
I N
Biased Humidity
Operational Life
OUT
OUT
Common Mode Impedance(Zc)
I N
OUT
9. Measuring method for common mode impedance.
Measured common mode impedance may be included measurement error due to stray capacitance, residual
inductance of test fixture.
To correct this error, the common mode impedance should be calculate as follows;
(1) Measure admittance of the fixture(opened), Go Bo.
(2) Measure impedance of the fixture(shorted), Rs Xs.
(3) Measure admittance of the specimen, Gm Bm.
(4) Calculate corrected impedance Z using the formula below.
Z = (Rx2+Xx2) 1/2
Where
Gm - Go
- Rs
Rx =
(Gm-Go)2 + (Bm-Bo)2
Xx =
- (Bm - Bo)
- Xs
(Gm-Go)2 + (Bm-Bo)2
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P5/10
10. P.C.B., Flux, Solder and Soldering condition
Test shall be done using P.C.B., Flux, Solder and Soldering condition which are specified in item 13 except the
case of being specified special condition.
11. Specification of Packaging
11.1 Appearance and Dimensions (24mm-wide,Plastic tape)
4.0×10pitch = 40.0±0.2
φ1.5+0.1/-0
*Dimension of the Cavity is measured
at the bottom side.
Direction of feed
(in
mm)
(@mm)
< Product direction >
11.2 Specification of Taping
(1) Packing quantity (Standard quantity)
Φ178 mm reel: 125 pcs. / reel
Φ330 mm reel: 500 pcs. / reel
(2) Packing Method
Products shall be packaged in each embossed cavity of plastic tape and sealed with cover tape.
(3) Spliced point
The cover tape has no spliced point.
(4) Sprocket Hole
The sprocket holes are to the right as the tape is pulled toward the user.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater, and are
not continuous. The specified quantity per reel is kept.
11.3 Pull Strength of Cover Tape
10N minimum
11.4 Peeling off force of Cover Tape
0.2N to 0.7N (minimum value is typical.)
Speed of Peeling off: 300 mm / min
165 to 180 degree
F
Cover tape
Plastic tape
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P6/10
11.5 Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (cover tape only and empty tape) and trailer-tape (empty tape) as follows.
【Packaging code:L(Φ178mm reel)】
【Packaging code:K(Φ330mm reel)】
(In mm)
11.6 Marking for reel
Customer part number, MURATA part number, Inspection number(*1), RoHS Marking(*2), Quantity, etc
*1) < Expression of Inspection No. > □□ ○○○○ ◇◇◇
①
②
③
① Factory code
② Date
First digit:year/Last digit of year
Second digit:Month/Jan. to Sep.→1 to 9,Oct. to Dec.→O,N,D
Third, Fourth digit:Day
③ Serial No.
*2) < Expression of RoHS Marking >
ROHS – Y (△)
① ②
① RoHS regulation conformity parts
② MURATA classification number
11.7 Marking for Outside package
Customer name, Purchasing Order Number, Customer Part Number, MURATA part number,
RoHS Marking (*2), Quantity, etc
11.8 Specification of Outer Case
Label
H
D
W
Reel
Standard Reel
Quantity in
Outer case
(Reel)
3
2
on a quantity of an order.
Outer case Dimensions
(mm)
W
D
H
Φ178mm
186
186
93
Φ330mm
340
340
85
*Above Outer Case size is typical. It depends
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P7/10
12.△
! Caution
12.1 Mounting Direction
Mount products in right direction.
Wrong direction which is 90°rotated from right direction causes not only open or short circuit but also flames or
other serious trouble.
Z
right direction
Z
wrong direction
12.2 Fail Safe
Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage that may
be caused by the abnormal function or the failure of our products.
12.3 Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1) Aircraft equipment
(2) Aerospace equipment
(3)Undersea equipment
(4)Power plant control equipment
(5) Medical equipment
(6) Transportation equipment (trains, ships, etc.)
(7) Traffic signal equipment
(8) Disaster prevention / crime prevention equipment
(9) Data-processing equipment
(10) Applications of similar complexity and /or reliability requirements
to the applications listed in the above
12.4 Attention regarding product's heat generation
Please pay special attention to the product’s heat generation such as beyond Operating Temperature range,
mounting product in close proximity to other products that radiate heat and beyond the rated current.
13. Notice
Products can only be soldered with reflow.
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
13.1 Flux and Solder
Flux
Use rosin-based flux.Do not use highly acidic flux
(with chlorine content exceeding0.2(wt)%)
Do not use water soluble flux.
Solder
Use Sn-3.0Ag-0.5Cu solder
Other flux (except above) please contacts us for details, then use.
13.2 Notes for Assembling
When installing by the flow soldering, the degradation of the insulation resistance sometimes occurs.
Products can only be soldered with reflow.
The use in flow soldering is reserved.
< Thermal Shock >
Pre-heating should be in such a way that the temperature difference between solder and products
surface is limited to 150 °C max. Also cooling into solvent after soldering should be in such a way that
the temperature difference is limited to 150 °C max.
Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality.
13.3 Attention Regarding P.C.B. Bending
The following shall be considered when designing P.C.B.'s and laying out products.
(1) P .C.B. shall be designed so that products are not subject to the mechanical stress for board warpage.
〔 Products Direction〕
a
Products shall be located in the sideways
direction (Length:a D *1
A > B
A > C
C
B
D
Slit
*1 A > D is valid when stress is added vertically to the perforation as with Hand Separation.
If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
(3) Mounting Components Near Screw Holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during
the tightening of the screw. Mount the component in a position as far away from the screw holes as possible.
Screw Hole
Recommended
13.4 Attention Regarding P.C.B. Design
< The Arrangement of Products >
P.C.B. shall be designed so that products are
far from the portion of perforation.
Portion of
Perforation
×
P.C.B.
The portion of perforation shall be designed
as narrow as possible, and shall be designed
so as not to be applied the stress in the
case of P.C.B. separation.
Portion of
Perforation
Products shall not be arranged on the line
of a series of holes when there are big holes in P.C.B.
(Because the stress concentrates on the line of holes.)
P.C.B.
○
○
Product
×
○
×
Product
< Products Placing >
Support pins shall be set under P.C.B
to prevent causing a warp to P.C.B.
during placing the products on the other
side of P.C.B.
Hole
< P.C.B. Separation >
P.C.B. shall not be separated with hand.
P.C.B. shall be separated with the fixture so as not to cause P.C.B. bending.
Pick- up nozzle
Product
P.C.B.
Support pin
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P9/10
13.5 Standard Land Dimensions
(1) Design the land pads for this part as shown above on both side printed circuit boards
(or a multiple layered substrate ).
(2) To use PLT10HH with high current such as its rated current 6A~18A,the pattern is also should be applicable
for such high current.
The thickness of copper foil for PLT10HH should be designed as temperature rise is lower than 40 degree C
(DC resistance of land and pattern should be low according to the current).
13.6 Reflow Soldering
Standard soldering profile and the limit soldering profile is as follows.
The excessive soldering conditions may cause leaching of the electrode and/or resulting in the deterioration
of product quality.
Temp
(°C)
260°C /10s
250±3°C
220°C
230°C
Limit Profile
180
150
Standard Profile
30~60s
60s max.
90s±30s
Pre-heating
Heating
Peak temperature
Cycle of reflow
Time(s)
Standard Profile
Limit Profile
150°C ~ 180°C , 90s ± 30s
above 220°C , 30s ~ 60s
above 230°C , 60s max.
250°C ± 3°C
260°C , 10s
2 times
2 times
(1)Solder paste printing for reflow soldering
· Standard thickness of solder paste should be 150 to 200 μm.
Incidentally, depending on the reflow condition and the way of heat conduction, the solder would not wet up the
terminal, being possible to lead to not enough connection between terminals and lands on the circuit
board / open circuit in the circuit board. In case of use, always evaluate this part in your products with actual use
condition.
· For the solder paste printing pattern, use standard land dimensions.
· For the resist and copper foil pattern, use standard land dimensions.
· Use Sn-3.0Ag-0.5Cu solder
MURATA MFG.CO.,LTD
Reference Only
Spec No. JEFL243B-9101G-01
P10/10
(2) Reworking with Soldering iron
· The following conditions shall be strictly followed when using a soldering iron.
Pre-heating: 150°C, 1 min
Soldering iron: 80W max.
Tip temperature/ Soldering time: 400°C ± 5°C, within 5s
Times : 2times max.
Note: Do not touch the products directly with the tip of the soldering iron.
13.7 Cleaning Conditions
Do not clean after soldering. If cleaning, please contact us.
13.8 Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to
the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to
the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
13.9 Operating Environment
Do not use this product under the following environmental conditions, on deterioration of the Insulation
Resistance and/or corrosion of Inner Electrode may result from the use.
(1) In the corrodible atmosphere (acidic gas, alkaline gas, chlorine, sulfur gas, organic gas and etc.)
(2) In the atmosphere where liquid such as organic solvent, may splash on the products.
(3) In the atmosphere where the temperature / humidity changes rapidly and it is easy to dew.
(4) In the atmosphere where the product is covered with dust or is subjected to salty breeze.
13.10 Storage Conditions
(1)Storage period
Use the products within 12 months after delivered.
Solderability should be checked if this period is exceeded.
(2)Storage conditions
• Products should be stored in the warehouse on the following conditions.
Temperature: -10°C to 40°C
Humidity: 15% to 85% relative humidity
No rapid change on temperature and humidity
• Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of
electrode, resulting in poor solderability.
• Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
• Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
• Products should be stored under the airtight packaged condition.
(3)Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
14. △
! Note
(1)Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2)You are requested not to use our product deviating from the reference specifications.
(3)The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO.,LTD