PTFM04BD222Q2N34BS

P1/4 Posistor® For Overheat Sensing 1. Part Numbering (Part Number) PT FM 04 BH 471 Q 2N34 BS Product ID Series Dimensions Temperature Characteristics Resistance Resistance Tolerance Individual Specifications Packaging 2. Ratings Part Number PTFM04BH471Q2N34BS PTFM04BG471Q2N34BS PTFM04BF471Q2N34BS PTFM04BE471Q2N34BS PTFM04BD471Q2N34BS PTFM04BC471Q2N34BS PTFM04BB471Q2N34BS PTFM04BH222Q2N34BS PTFM04BG222Q2N34BS PTFM04BF222Q2N34BS PTFM04BE222Q2N34BS PTFM04BD222Q2N34BS PTFM04BC222Q2N34BS PTFM04BB222Q2N34BS Temp. Char. (C.P.) BH BG BF BE BD BC BB BH BG BF BE BD BC BB Resistance Value 25°C 100ohm max. 330ohm max. ※ TS 470ohm min./60°C 470ohm min./70°C 470ohm min./80°C 470ohm min./90°C 470ohm min./100°C 470ohm min./110°C 470ohm min./120°C 2.2kohm min./60°C 2.2kohm min./70°C 2.2kohm min./80°C 2.2kohm min./90°C 2.2kohm min./100°C 2.2kohm min./110°C 2.2kohm min./120°C TS-10°C 330ohm max./50°C 330ohm max./60°C 330ohm max./70°C 330ohm max./80°C 330ohm max./90°C 330ohm max./100°C 330ohm max./110°C 1.5kohm max./50°C 1.5kohm max./60°C 1.5kohm max./70°C 1.5kohm max./80°C 1.5kohm max./90°C 1.5kohm max./100°C 1.5kohm max./110°C Max. Voltage Max. Current 16V DC. 0.1A 16V DC. 0.1A ※ TS = Sensing Temperature • External dielectric withstand voltage between metallic terminal and lead wire. : 500 VDC / 5±1 sec. 3. Dimensions (mm) 3.0±0.3 7.5±0.4 Dia 3.7±0.3 0.5±0.05 13.2±0.5 9.45±0.5 3.2±0.4 6.4±0.4 3.5±1.5 Coating extension :2.5mm max 39±5 Dia0.5±0.05 4. Quantity (Standard Quantity) 200pcs.／unit bag. Murata Manufacturing Co.,Ltd. This information may be changed without a previous notice. JWA01BK-E1019I P2/4 BH 1000 BG BF BE BD BC BB Resistance - Temperature Characteristic Resistance Change (R/R25) 100 10 1 0.1 -10 0 10 20 30 40 50 60 70 80 Temperature (deg C) This information may be changed without a previous notice. 90 100 110 120 130 140 BH-007' P3/4 Notice for use Caution 1. This product is designed for application which is used under ordinary environment.(room temperature, normal humidity, normal pressure) Do not expose this to the following environments, because all these factor can deteriorate the characteristic of this and can cause failure or burn out. (1)Corrosive gas or deoxidizing gas（Cl2, H2S, NH3, SOx, NOx etc.） (2)Volatile, flammable gas (3)Dusty place (4)Place in a vacuum, reducing or putting pressure (5)Place in splashed water, or high humidity and dewing place (6)Salt water, oil, chemical liquid and solvent (7)Vibratile place (8)Other place equivalent to the above 2. Limitation of Applications Please contact us before using our products for the under-mentioned applications requiring especially high reliability in order to prevent defects which might directly cause damage to other party’s life body or property (listed below). (1)Aircraft equipment (2)Aerospace equipment (3)Undersea equipment (4)Power plant control equipment (5)Medical equipment (6)Transportation equipment (automobiles, trains, ships, etc.) (7)Traffic signal equipment (8)Disaster prevention / Crime prevention equipment (9)Data-processing equipment (10) Applications of similar complexity or with reliability requirements comparable to the applications listed in the above. 3. Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. Notice 1. Do not apply abnormal voltage/current exceeding the specified maximum value. Because they may deteriorate or destroy PTC element. 2. Use this product within the specified temperature. A higher temperature may deteriorate the characteristic or material. 3. In case of mounting this product with screw , please do not apply an excessive tensile stress(9.8N) between resin case and lead. 4. Do not apply an excessive force(9.8N) to the lead. Otherwise, it may cause break off the junction between lead and element, may crack element or element may comes off resin case. Therefore, hold of element side lead wire is recommended when lead wire is bent or cut. 5. This product does not have waterproof construction. A splashed water may cause failure mode such as deterioration of characteristic or current leak. So, Do NOT apply cleaning to immerse it into water or any solvent. 6. If you coat this product by resin, please evaluate the qualityl of this product before you use it. The stress of fource which is caused by coating materials or heat cycles may cause failure mode such as deterioration of characteristic or current leak in worst case. 7. This product is using the solder of 221+/-5 ℃ of melting points, in order to connect ceramics with a lead wire. Do not heat up a terminal area of this product over 180 ℃. 8. The ceramic element of this product is fragile, and care must be taken not to load a excessive press-force or not to give a shock at handling. Such forces may cause cracking or chipping. MURARA MANUFACTURING CO., LTD. This information may be changed without a previous notice. CE-004AJ P4/4 9. When the lead of this product is soldered, pay attention as follows to avoid the decline of element characteristic or break down the element. (1) Use Rosin type flux or non-activated flux(the content of chlorine shall be less than 0.2%) (2) Do not dip the body into flux. (Flux shall be coated to lead wire only for soldering.) (3) The pre-heat up should be conducted without melting the soldering of this product. 10. Do not apply tensile force or separating force to lead wire at soldering. 11. Do not touch the resin case by soldering iron. The soldering point shall be min. 5 mm away from the root of lead wire. Please solder the following conditions. ･Iron Tip Temperature : 360 degree C max. ･Soldering Time : 4 seconds max. / 1 terminal ･Number of Soldering : 1 12. To keep solderability of product from declining, following storage condition is recommended. (1) Storage condition : Temperature : -10 to +40°C Humidity : less than 75%RH（not dewing condition） (2) Term: Please use this product within 6 months after shipment by first-in and first-out stocking system. (3) Handling after seal open: After unpacking of the minimum package, reseal it promptly or store it inside a sealed container with a drying agent. (4) Place: Do not store this product in corrosive gas(SOx, Cl etc) or under sun-light. 13. This product is to be mounted to the part where heat should be detected as shown below. Screw Screw POSISTOR Transistor Transistor Radiative Plate Radiative Plate POSISTOR As it happen that detected heat will change after this product would be mounted, please make sure that your product has been evaluated confirmed after this product will be mounted. 14. The lag terminal plate is inserted into resin case. Incase of mounting this product with screw, please do not give strength to resin case. 15. Please do not use adhesive to mounting. MURARA MANUFACTURING CO., LTD. This information may be changed without a previous notice. CE-004AJ