RCE7U2J681J2M1H03A

Reference Specification Leaded MLCC for Automotive with AEC-Q200 RCE Series Product specifications in this catalog are as of Dec. 2017, and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering.Please read rating and Cautions first. Reference only CAUTION 1. OPERATING VOLTAGE When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage containing these irregular voltage. When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter), be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or impulse withstand established for each equipment should be taken into considerations. Voltage DC Voltage Positional Measurement Vo-p DC+AC Voltage Vo-p AC Voltage Vp-p Pulse Voltage(1) Vp-p Pulse Voltage(2) Vp-p 2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.), applied voltage should be the load such as self-generated heat is within 20 C on the condition of atmosphere temperature 25 C. Please contact us if self-generated heat is occurred with Class 1 capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal capacity-K of 0.1mm and be in the condition where capacitor is not affected by radiant heat of other components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s characteristics and reliability. 3. Fail-safe Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. 4. OPERATING AND STORAGE ENVIRONMENT The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed 5 to 40 C and 20 to 70%. Use capacitors within 6 months. 5. VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use. 6. SOLDERING When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. 7. BONDING AND RESIN MOLDING, RESIN COAT In case of bonding, molding or coating this product, verify that these processes do not affect the quality of capacitor by testing the performance of a bonded or molded product in the intended equipment. In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short circuit. The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or ceramic element cracking of a capacitor in a temperature cycling. 8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT When the outer coating is hot (over 100 C) after soldering, it becomes soft and fragile. So please be careful not to give it mechanical stress. EGLEDMNO03 1 / 15 Reference only Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. 9. LIMITATION OF APPLICATIONS Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party’s life, body or property. 1. Aircraft equipment 2. Aerospace equipment 3. Undersea equipment 4. Power plant control equipment 5. Medical equipment 6. Transportation equipment (vehicles, trains, ships, etc.) 7. Traffic signal equipment 8. Disaster prevention / crime prevention equipment 9. Data-processing equipment exerting influence on public 10. Application of similar complexity and/or reliability requirements to the applications listed in the above. NOTICE 1. CLEANING (ULTRASONIC CLEANING) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity : Output of 20 watts per liter or less. Rinsing time : 5 min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 2. Soldering and Mounting Insertion of the Lead Wire • When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire. • Insert the lead wire into the PCB with a distance appropriate to the lead space. 3. CAPACITANCE CHANGE OF CAPACITORS • Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.) Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant circuit. Please contact us if you need a detail information. NOTE 1. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2. You are requested not to use our product deviating from this specification. EGLEDMNO03 2 / 15 Reference only 1. Application This specification is applied to Leaded MLCC RCE series in accordance with AEC-Q200 requirements used for Automotive Electronic equipment. 2. Rating  Part number configuration ex.) RCE 7U 2E Series Temperature Characteristic Rated voltage 102 J 1 K1 H03 B Capacitance Capacitance tolerance Dimension code Lead code Individual specification code Packing style code  Temperature characteristic Temp. Temp. Range Code Char. 7U U2J  Rated voltage Code 2E 2J 3A 25～125C Cap. Change (Within%) Standard Temp. 750+/-120 25C Operating Temp. Range -55～125C Rated voltage DC250V DC630V DC1000V  Capacitance The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF. ex.) In case of 102. 10102 = 1000pF  Capacitance tolerance Code Capacitance Tolerance J +/-5%  Dimension code Code Dimensions (LxW) mm max. 1 4.0 x 3.5 2 5.5 x 4.0 3 5.5 x 5.0 4 7.5 x 5.5 5 7.5 x 8.0 U 7.7 x 13.0  Lead code Code B1 E1 K1 M1 Lead style Straight type Straight taping type Inside crimp type Inside crimp taping type Lead spacing (mm) 5.0+/-0.8 5.0+0.6/-0.2 5.0+/-0.8 5.0+0.6/-0.2 Lead wire is solder coated CP wire. ETRCE04A 3 / 15 Reference only  Individual specification code Murata’s control code Please refer to  Part number list .  Packing style code Code Packing style A Taping type of Ammo B Bulk type 3. Marking Temp. char. Capacitance : Letter code : U(U2J Char.) : Actual numbers (Less than 100pF) 3 digit numbers (100pF and over) Capacitance tolerance : Code Rated voltage : Letter code : 4 (DC250V only. Except dimension code : 1) Letter code : 7 (DC630V only.) Letter code : A (DC1000V only.) Company name code : Abbreviation : (Except dimension code : 1) (Ex.) Rated voltage Dimensions 1 DC250V DC630V DC1000V ―― ―― U 102J 2 103 J4U 472 J7U 102 JAU 3,4 473 J4U 103 J7U 472 JAU 333 J7U 103 JAU 5,U ―― ETRCE04A 4 / 15 Reference only 4. Part number list Unit : mm Customer Part Number Murata Part Number DC Rated T.C. Volt. (V) Cap. Cap. tol. Dimension (mm) L W W1 F T Size Pack Lead qty. Code (pcs) RCE7U2E101J1K1H03B U2J 250 100pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E151J1K1H03B U2J 250 150pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E221J1K1H03B U2J 250 220pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E331J1K1H03B U2J 250 330pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E471J1K1H03B U2J 250 470pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E681J1K1H03B U2J 250 680pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E102J1K1H03B U2J 250 1000pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E152J1K1H03B U2J 250 1500pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E222J1K1H03B U2J 250 2200pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E332J1K1H03B U2J 250 3300pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E472J1K1H03B U2J 250 4700pF ±5% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCE7U2E682J2K1H03B U2J 250 6800pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2E103J2K1H03B U2J 250 10000pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J100J2K1H03B U2J 630 10pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J150J2K1H03B U2J 630 15pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J220J2K1H03B U2J 630 22pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J330J2K1H03B U2J 630 33pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J470J2K1H03B U2J 630 47pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J680J2K1H03B U2J 630 68pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J101J2K1H03B U2J 630 100pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J151J2K1H03B U2J 630 150pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J221J2K1H03B U2J 630 220pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J331J2K1H03B U2J 630 330pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J471J2K1H03B U2J 630 470pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J681J2K1H03B U2J 630 680pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J102J2K1H03B U2J 630 1000pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J152J2K1H03B U2J 630 1500pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J222J2K1H03B U2J 630 2200pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J332J2K1H03B U2J 630 3300pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J472J2K1H03B U2J 630 4700pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U2J682J3K1H03B U2J 630 6800pF ±5% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCE7U2J103J3K1H03B U2J 630 10000pF ±5% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCE7U2J153J4K1H03B U2J 630 15000pF ±5% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCE7U2J223J4K1H03B U2J 630 22000pF ±5% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCE7U2J333J5B1H03B U2J 630 33000pF ±5% 7.5 8.0 - 5.0 4.0 5B1 500 RCE7U2J473J5B1H03B U2J 630 47000pF ±5% 7.5 8.0 - 5.0 4.0 5B1 500 RCE7U2J943JUB1H03B U2J 630 94000pF ±5% 7.7 13.0 - 5.0 4.0 UB1 200 5 / 15 Reference only Unit : mm Customer Part Number Murata Part Number DC Rated T.C. Volt. (V) Cap. Cap. tol. Dimension (mm) L W W1 F T Size Pack Lead qty. Code (pcs) RCE7U3A100J2K1H03B U2J 1000 10pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A150J2K1H03B U2J 1000 15pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A220J2K1H03B U2J 1000 22pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A330J2K1H03B U2J 1000 33pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A470J2K1H03B U2J 1000 47pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A680J2K1H03B U2J 1000 68pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A101J2K1H03B U2J 1000 100pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A151J2K1H03B U2J 1000 150pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A221J2K1H03B U2J 1000 220pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A331J2K1H03B U2J 1000 330pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A471J2K1H03B U2J 1000 470pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A681J2K1H03B U2J 1000 680pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A102J2K1H03B U2J 1000 1000pF ±5% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCE7U3A152J3K1H03B U2J 1000 1500pF ±5% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCE7U3A222J3K1H03B U2J 1000 2200pF ±5% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCE7U3A332J4K1H03B U2J 1000 3300pF ±5% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCE7U3A472J4K1H03B U2J 1000 4700pF ±5% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCE7U3A682J5B1H03B U2J 1000 6800pF ±5% 7.5 8.0 - 5.0 4.0 5B1 500 RCE7U3A103J5B1H03B U2J 1000 10000pF ±5% 7.5 8.0 - 5.0 4.0 5B1 500 RCE7U3A203JUB1H03B U2J 1000 20000pF ±5% 7.7 13.0 - 5.0 4.0 UB1 200 6 / 15 Reference only Unit : mm Customer Part Number Murata Part Number DC Rated T.C. Cap. Cap. tol. volt. (V) Dimension (mm) L W W1 F T Size Pack Lead qty. H/H0 Code (pcs) RCE7U2E101J1M1H03A U2J 250 100pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E151J1M1H03A U2J 250 150pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E221J1M1H03A U2J 250 220pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E331J1M1H03A U2J 250 330pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E471J1M1H03A U2J 250 470pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E681J1M1H03A U2J 250 680pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E102J1M1H03A U2J 250 1000pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E152J1M1H03A U2J 250 1500pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E222J1M1H03A U2J 250 2200pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E332J1M1H03A U2J 250 3300pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E472J1M1H03A U2J 250 4700pF ±5% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCE7U2E682J2M1H03A U2J 250 6800pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2E103J2M1H03A U2J 250 10000pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J100J2M1H03A U2J 630 10pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J150J2M1H03A U2J 630 15pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J220J2M1H03A U2J 630 22pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J330J2M1H03A U2J 630 33pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J470J2M1H03A U2J 630 47pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J680J2M1H03A U2J 630 68pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J101J2M1H03A U2J 630 100pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J151J2M1H03A U2J 630 150pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J221J2M1H03A U2J 630 220pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J331J2M1H03A U2J 630 330pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J471J2M1H03A U2J 630 470pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J681J2M1H03A U2J 630 680pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J102J2M1H03A U2J 630 1000pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J152J2M1H03A U2J 630 1500pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J222J2M1H03A U2J 630 2200pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J332J2M1H03A U2J 630 3300pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J472J2M1H03A U2J 630 4700pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U2J682J3M1H03A U2J 630 6800pF ±5% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCE7U2J103J3M1H03A U2J 630 10000pF ±5% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCE7U2J153J4M1H03A U2J 630 15000pF ±5% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCE7U2J223J4M1H03A U2J 630 22000pF ±5% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCE7U2J333J5E1H03A U2J 630 33000pF ±5% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 RCE7U2J473J5E1H03A U2J 630 47000pF ±5% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 RCE7U2J943JUE1H03A U2J 630 94000pF ±5% 7.7 13.0 - 5.0 4.0 17.5 UE1 1500 7 / 15 Reference only Unit : mm Customer Part Number Murata Part Number DC Rated T.C. Cap. Cap. tol. volt. (V) Dimension (mm) L W W1 F T Size Pack Lead qty. H/H0 Code (pcs) RCE7U3A100J2M1H03A U2J 1000 10pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A150J2M1H03A U2J 1000 15pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A220J2M1H03A U2J 1000 22pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A330J2M1H03A U2J 1000 33pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A470J2M1H03A U2J 1000 47pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A680J2M1H03A U2J 1000 68pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A101J2M1H03A U2J 1000 100pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A151J2M1H03A U2J 1000 150pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A221J2M1H03A U2J 1000 220pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A331J2M1H03A U2J 1000 330pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A471J2M1H03A U2J 1000 470pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A681J2M1H03A U2J 1000 680pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A102J2M1H03A U2J 1000 1000pF ±5% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCE7U3A152J3M1H03A U2J 1000 1500pF ±5% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCE7U3A222J3M1H03A U2J 1000 2200pF ±5% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCE7U3A332J4M1H03A U2J 1000 3300pF ±5% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCE7U3A472J4M1H03A U2J 1000 4700pF ±5% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCE7U3A682J5E1H03A U2J 1000 6800pF ±5% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 RCE7U3A103J5E1H03A U2J 1000 10000pF ±5% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 RCE7U3A203JUE1H03A U2J 1000 20000pF ±5% 7.7 13.0 - 5.0 4.0 17.5 UE1 1500 8 / 15 Reference only 5. AEC-Q200 Murata Standard Specifications and Test Methods No. 1 2 AEC-Q200 Test Item Pre-and Post-Stress Electrical Test High Appearance Temperature Capacitance Exposure Change (Storage) Q Specification AEC-Q200 Test Method No defects or abnormalities Within 3% or 0.3pF (Whichever is larger) 30pF  C : Q  350 10pF  C  30pF : Q  275+5C/2 10pF > C : Q  200+10C Sit the capacitor for 1,00012h at 1503C. Let sit for 242h at *room condition, then measure. C : Nominal Capacitance (pF) More than 1,000M or 50 MF (Whichever is smaller) Temperature Appearance No defects or abnormalities Cycling Capacitance Within 5% or 0.5pF Change (Whichever is larger) Q 30pF  C : Q  350 10pF  C  30pF : Q  275+5C/2 10pF > C : Q  200+10C I.R. 3 I.R. 4 Moisture Resistance Appearance Capacitance Change Q Step Temp. (C) Time (min.) C : Nominal Capacitance (pF) 1,000M or 50M·F min. (Whichever is smaller) 1 -55+0/-3 153 2 Room Temp. 1 3 125+3/-0 153 4 Room Temp. 1 Apply the 24h heat (25 to 65C) and humidity (80 to 98%) treatment shown below, 10 consecutive times. Let sit for 24±2 h at *room condition, then measure. No defects or abnormalities Within 5% or  0.5pF (Whichever is larger) 30pF  C : Q  200 30pF > C : Q  100+10C/3 Humidity Temperature 8098 Humidity Humidity C 9098 9098 70 65 60 55 50 45 40 35 30 25 +10 20 - 2 C 15 10 Initial measurement 5 0 -5 -10 One cycle 24 hours C : Nominal Capacitance(pF) 500M or 25M·F min. (Whichever is smaller) Humidity 8098 Humidity 9098 Temperature I.R. Perform the 1,000 cycles according to the four heat treatments listed in the following table. Let sit for 24±2 h at *room condition, then measure. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 5 Biased Humidity Appearance Capacitance Change Q I.R. Hours Apply the rated voltage and DC1.3+0.2/-0 V (add 100k resistor) at 853C and 80 to 85% humidity for 1,00012h. Remove and let sit for 24±2 h at *room condition, then measure. The charge/discharge current is less than 50mA. No defects or abnormalities Within 5% or  0.5pF (Whichever is larger) 30pF  C : Q  200 30pF > C : Q  100+10C/3 C : Nominal Capacitance(pF) 500M or 25M·F min. (Whichever is smaller) * “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa ESRCE04C 9 / 15 Reference only AEC-Q200 Test Item No. 6 Operational Life Appearance Capacitance Change Q I.R. 7 8 9 10 11 12 External Visual Physical Dimension Marking Resistance to Appearance Solvents Capacitance Q Mechanical Shock Vibration Specification No defects or abnormalities Within 3% or 0.3pF (Whichever is larger) 30pF  C : Q  350 10pF  C  30pF : Q  275+5C/2 10pF > C : Q  200+10C C : Nominal Capacitance (pF) 1,000M or 50M·F min. (Whichever is smaller) No defects or abnormalities Within the specified dimensions To be easily legible. No defects or abnormalities Within the specified tolerance 30pF  C : Q  1,000 30pF > C : Q  400+20C I.R. C : Nominal Capacitance (pF) More than 10,000M or 500 MF (Whichever is smaller) Appearance No defects or abnormalities Capacitance Within the specified tolerance Q 30pF  C : Q  1,000 30pF > C : Q  400+20C Appearance C : Nominal Capacitance (pF) No defects or abnormalities Capacitance Within the specified tolerance Q 30pF  C : Q  1,000 30pF > C : Q  400+20C C : Nominal Capacitance( pF) 13-1 13-2 13-3 14 Resistance to Soldering Heat (NonPreheat) Resistance to Soldering Heat (OnPreheat) Resistance to Soldering Heat (soldering iron method) Appearance No defects or abnormalities Capacitance Change Dielectric Strength (Between terminals) Within 2.5% or 0.25pF (Whichever is larger) No defects Appearance No defects or abnormalities Capacitance Change Dielectric Strength (Between terminals) Within 2.5% or 0.25pF (Whichever is larger) No defects Appearance No defects or abnormalities Capacitance Change Dielectric Strength (Between terminals) Within 2.5% or 0.25pF (Whichever is larger) No defects Thermal Shock Appearance Capacitance Change Q I.R. AEC-Q200 Test Method Apply voltage in Table for 1,00012h at 1253C. Let sit for 24±2 h at *room condition, then measure. The charge/discharge current is less than 50mA. Rated Voltage Test Voltage DC250V 150% of the rated voltage DC630V DC1000V 120% of the rated voltage Visual inspection Using calipers and micrometers. Visual inspection Per MIL-STD-202 Method 215 Solvent 1 : 1 part (by volume) of isopropyl alcohol 3 parts (by volume) of mineral spirits Solvent 2 : Terpene defluxer Solvent 3 : 42 parts (by volume) of water 1part (by volume) of propylene glycol monomethyl ether 1 part (by volume) of monoethanolamine Three shocks in each direction should be applied along 3 mutually perpendicular axes of the test specimen (18 shocks). The specified test pulse should be Half-sine and should have a duration :0.5ms, peak value:1,500G and velocity change: 4.7m/s. The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 2,000Hz. The frequency range, from 10 to 2,000Hz and return to 10Hz, should be traversed in approximately 20 min. This motion should be applied for 12 items in each 3 mutually perpendicular directions (total of 36 times). The lead wires should be immersed in the melted solder 1.5 to 2.0mm from the root of terminal at 2605C for 10.1 seconds. • Post-treatment Capacitor should be stored for 242 hours at *room condition. First the capacitor should be stored at 120+0/-5C for 60+0/-5 seconds. Then, the lead wires should be immersed in the melted solder 1.5 to 2.0mm from the root of terminal at 2605C for 7.5+0/-1 seconds. • Post-treatment Capacitor should be stored for 242 hours at *room condition. Test condition Termperature of iron-tip : 35010C Soldering time : 3.50.5 seconds Soldering position Straight Lead:1.5 to 2.0mm from the root of terminal. Crimp Lead:1.5 to 2.0mm from the end of lead bend. • Post-treatment Capacitor should be stored for 242 hours at *room condition. Perform the 300 cycles according to the two heat treatments listed in the following table(Maximum transfer time is 20s.). Let sit for 24±2 h at *room condition, then measure. No defects or abnormalities Within 5% or 0.5pF (Whichever is larger) 30pF  C : Q  350 10pF  C  30pF : Q  275+5C/2 10pF > C : Q  200+10C C : Nominal Capacitance (pF) 1,000M or 50M·F min. (Whichever is smaller) Step Temp. (C) Time (min.) * “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa ESRCE04C 10 / 15 1 2 -55+0/-3 125+3/-0 153 153 Reference only AEC-Q200 Test Item No. 15 ESD Specifications Appearance No defects or abnormalities Capacitance Within the specified tolerance Q I.R. 16 Solderability 17 Electrical Apperance CharacteCapacitance rization AEC-Q200 Test Method Per AEC-Q200-002 30pF  C : Q  1,000 30pF > C : Q  400+20C C : Nominal Capacitance (pF) More than 10,000M or 500 MF (Whichever is smaller) Lead wire should be soldered with uniform coating on Should be placed into steam aging for 8h15 min. The terminal of capacitor is dipped into a solution of ethanol the axial direction over 95% of the circumferential (JIS K 8101) and rosin (JIS K 5902) (25% rosin in weight direction. propotion).Immerse in solder solution for 20.5 seconds. In both cases the depth of dipping is up to about 1.5 to 2mm from the terminal body. Temp. of solder : 2455C Lead Free Solder(Sn-3.0Ag-0.5Cu) 2355C H60A or H63A Eutectic Solder No defects or abnormalities Visual inspection. Within the specified tolerance The capacitance, Q should be measured at 25C at the frequency and voltage shown in the table. Q 30pF  C : Q  1,000 30pF > C : Q  400+20C I.R. Between Terminals 10,000M or 500MF min. (Whichever is smaller) Dielectric Strength Between Terminals No defects or abnormalities Nominal Cap. C  1000pF C > 1000pF C : Nominal Capacitance (pF) Rated Voltage Test Voltage DC250V 200% of the rated voltage DC1000V 18 Terminal Strength Tensile Strength No defects or abnormalities Termination not to be broken or loosened Voltage AC0.5 to 5V(r.m.s.) AC10.2V(r.m.s.) The insulation resistance should be measured with DC500V (DC250V in case of rated voltage : DC250V) at 25 C within 2 min. of charging. The capacitor should not be damaged when voltage in Table is applied between the terminations for 1 to 5 seconds. (Charge/Discharge current  50mA.) DC630V Body Insulation Frequency 10.1MHz 10.1kHz DC1300V The capacitor is placed in a container with metal balls of 1mm diameter so that each terminal, short-circuit is kept approximately 2mm from the balls, and 200% of the rated DC voltage(130% of the rated voltage in case of rated voltage : DC1000V) is impressed for 1 to 5 seconds between capacitor terminals and metal balls. (Charge/Discharge current  50mA.) As in the figure, fix the capacitor body, apply the force gradually to each lead in the radial direction of the capacitor until reaching 10N and then keep the force applied for 101 seconds.  F Bending Strength 19 Capacitance Temperature Characteristics Termination not to be broken or loosened Within the specified Tolerance. 25C~125C : -750±120 ppm/°C -55C~25C : -750+120/-347 ppm/°C Each lead wire should be subjected to a force of 2.5N and then be bent 90° at the point of egress in one direction. Each wire is then returned to the original position and bent 90° in the opposite direction at the rate of one bend per 2 to 3 seconds. The capacitance change should be measured after 5min. at each specified temperature step. Step 1 2 3 4 5 Temperature(C) 252 -553 252 1253 252 The temperature coefficient is determind using the capacitance measured in step 3 as a reference. When cycling the temperature sequentially from step 1 through 5 (-55C to +125C) the capacitance should be within the specified tolerance for the temperature coefficient and capacitance change as Table A. The capacitance drift is caluculated by dividing the differences betweeen the maximum and minimum measured values in the step 1, 3 and 5 by the capacitance value in step 3. * “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa ESRCE04C 11 / 15 Reference only 6. Packing specification Bulk type (Packing style code : B) 1 2 The number of packing = Packing quantity  n The size of packing case and packing way 1 : Please refer to [Part number list]. 2 : Standard n = 20 (bag) Polyethylene bag Partition Note) The outer package and the number of outer packing be changed by the order getting amount. 270 max. 125 max. 340 max. Unit : mm Ammo pack taping type (Packing style code : A)  A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.  When body of the capacitor is piled on other body under it. The size of packing case and packing way 240 max. Position of label Unit : mm 340 max. Hold down tape Capacitor 51 max. Base tape Hold down tape upper EKBCRPE01 12 / 15 Reference only 7. Taping specification 7-1. Dimension of capacitors on tape Straight taping type < Lead code : E1 > Pitch of component 12.7mm / Lead spacing 5.0mm P2 h1 P 0 h2 S Marking H d W1 t1 t2 W0 L  D0 W F W2 e P1 P0 Unit : mm Item Code Dimensions Pitch of component P 12.7+/-1.0 Pitch of sprocket hole P0 12.7+/-0.2 Lead spacing F 5.0+0.6/-0.2 Length from hole center to component center P2 6.35+/-1.3 Length from hole center to lead P1 3.85+/-0.7 Deviation along tape, left or right defect S 0+/-2.0 Carrier tape width W 18.0+/-0.5 Position of sprocket hole W1 9.0+0/-0.5 For straight lead type H 17.5+/-0.5 Remarks Deviation of progress direction They include deviation by lead bend . Deviation of tape width direction 0.5 max. Protrusion length Diameter of sprocket hole D0 4.0+/-0.1 Lead diameter d 0.50+/-0.05 Total tape thickness t1 0.6+/-0.3 Total thickness of tape and lead wire t2 1.5 max. h1 h2 2.0 max.（Dimension code：U） 1.0 max.（except as above） Portion to cut in case of defect L 11.0+0/-1.0 Hold down tape width W0 9.5 min. Hold down tape position W2 1.5+/-1.5 Coating extension on lead e 2.0 max.（Dimension code：U） 1.5 max.（except as above） Deviation across tape ETP1E101A 13 / 15 They include hold down tape thickness. Reference only Inside crimp taping type < Lead code : M1 > Pitch of component 12.7mm / Lead spacing 5.0mm 0 P P2 h2 h1 S Marking t1 t2 W W0 L  D0 W1 d H0 F P1 W2 e P0 Unit : mm Item Code Dimensions Pitch of component P 12.7+/-1.0 Pitch of sprocket hole P0 12.7+/-0.2 Lead spacing F 5.0+0.6/-0.2 Length from hole center to component center P2 6.35+/-1.3 Length from hole center to lead P1 3.85+/-0.7 Deviation along tape, left or right defect S 0+/-2.0 Carrier tape width W 18.0+/-0.5 Position of sprocket hole W1 9.0+0/-0.5 H0 16.0+/-0.5 Lead distance between reference and bottom plane Remarks Deviation of progress direction They include deviation by lead bend . Deviation of tape width direction 0.5 max. Protrusion length Diameter of sprocket hole D0 4.0+/-0.1 Lead diameter d 0.50+/-0.05 Total tape thickness t1 0.6+/-0.3 Total thickness of tape and lead wire t2 1.5 max. h1 h2 2.0 max.（Dimension code：W） 1.0 max.（except as above） Portion to cut in case of defect L 11.0+0/-1.0 Hold down tape width W0 9.5 min. Hold down tape position W2 1.5+/-1.5 Coating extension on lead e Up to the end of crimp Deviation across tape ETP1M101 14 / 15 They include hold down tape thickness. Reference only 7-2. Splicing way of tape 1) Adhesive force of tape is over 3N at test condition as below. W Hold down tape Base tape 2) Splicing of tape a) When base tape is spliced Base tape shall be spliced by cellophane tape. (Total tape thickness shall be less than 1.05mm.) Progress direction in production line Hold down tape Base tape About 30 to 50 Cellophane tape No lifting for the direction of progressing Unit : mm b) When hold down tape is spliced Hold down tape shall be spliced with overlapping. (Total tape thickness shall be less than 1.05mm.) ape are spliced Base tape and adhesive tape shall be spliced with splicing tape. 20 to 30 Hold down tape Progress direction in production line Base tape Unit : mm c) When both tape are spliced Base tape and hold down tape shall be spliced with splicing tape. ETP2R01 15 / 15 Appendix EU RoHS and Halogen Free This products of the following crresponds to EU RoHS and Halogen Free　 (1) RoHS 　EU RoHs 2011/65/EC compliance　 　maximum concentration values tolerated by weight in homogeneous materials 　・1000 ppm maximum Lead 　・1000 ppm maximum Mercury 　・100 ppm maximum Cadmium 　・1000 ppm maximum Hexavalent chromium 　・1000 ppm maximum Polybrominated biphenyls (PBB) 　・1000 ppm maximum Polybrominated diphenyl ethers (PBDE) (2) Halogen-Free 　The International Electrochemical Commission’s (IEC) Definition 　of Halogen-Free (IEC 61249-2-21) compliance 　 　・900 ppm maximum chlorine 　・900 ppm maximum bromine 　・1500 ppm maximum total chlorine and bromine