Reference Specification
Leaded MLCC for Automotive (Powertrain/Safety)
RCE Series
Product specifications in this catalog are as of Oct. 2023, and are subject to change or
obsolescence without notice.
Please consult the approval sheet before ordering.Please read rating and Cautions first.
＜Reference＞Please kindly use our website.
Please refer to the product information page for more information on ceramic capacitors.→
Ceramic capacitor product information
Various data can be obtained directly from the product search.→ Product search (SMD) /
Product search (Lead Type)
Reference only
CAUTION
1. OPERATING VOLTAGE
1. Do not apply a voltage to the capacitor that exceeds the rated voltage as called out in the specifications.
1-1. Applied voltage between the terminals of a capacitor shall be less than or equal to the rated voltage.
(1) When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated
DC voltage. When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed
the rated DC voltage.
(2) Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC
voltage.
Typical Voltage Applied to the DC Capacitor
DC Voltage
V0-p
DC+AC Voltage
V0-p
AC Voltage
Vp-p
Pulse Voltage
Vp-p
(E: Maximum possible applied voltage.)
1-2. Influence of over voltage
Over voltage that is applied to the capacitor may result in an electrical short circuit caused by the
breakdown of the internal dielectric layers. The time duration until breakdown depends on the applied
voltage and the ambient temperature.
2. Use a safety standard certified capacitor in a power supply input circuit (AC filter), as it is also necessary
to consider the withstand voltage and impulse withstand voltage defined for each device.
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.
Be sure to take into account the heat generated by the capacitor itself.
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),
applied voltage should be the load such as self-generated heat is within 20 °C on the condition of
atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1
capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal
capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other
components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s
characteristics and reliability.
3. FAIL-SAFE
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that
may be caused by the abnormal function or the failure of our product.
4. OPERATING AND STORAGE ENVIRONMENT
The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the
like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify
that these processes do not affect product quality by testing the performance of a cleaned, bonded or
molded product in the intended equipment. Store the capacitors where the temperature and relative
humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.
Use capacitors within 6 months after delivered. Check the solderability after 6 months or more.
EGLEDMNO03A
1/23
Reference only
CAUTION
5. VIBRATION AND IMPACT
Do not expose a capacitor or its leads to excessive shock or vibration during use.
Excessive shock or vibration may cause to fatigue destruction of lead wires mounted on the circuit board.
If necessary, take measures to hold a capacitor on the circuit boards by adhesive, molding resin or
coating and other.
Please confirm there is no influence of holding measures on the product with an intended equipment.
6. SOLDERING
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the
capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may
result in thermal shocks that can crack the ceramic element.
Please verify that the soldering process does not affect the quality of capacitors.
6-1. Flow Soldering
Soldering temperature
Soldering time
Preheating temperature
Preheating time
: 260 ℃ max.
: 7.5 s max.
: 120 ℃ max.
: 60 s max.
6-2. Soldering Iron
Temperature of iron-tip
Soldering iron wattage
Soldering time
: 350 ℃ max.
: 60 W max.
: 3.5 s max.
7. BONDING AND RESIN MOLDING, RESIN COAT
In case of bonding, molding or coating this product, verify that these processes do not affect the quality
of capacitor by testing the performance of a bonded or molded product in the intended equipment.
In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins
containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer
coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short
circuit.
The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or
ceramic element cracking of a capacitor in a temperature cycling.
8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT
When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.
So please be careful not to give it mechanical stress.
Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial
dispersion when the product is used.
EGLEDMNO03A
2/23
Reference only
CAUTION
9. LIMITATION OF APPLICATIONS
The products listed in the specification(hereinafter the product(s) is called as the “Product(s)”) are designed
and manufactured for applications specified in the specification. (hereinafter called as the “Specific
Application”)
We shall not warrant anything in connection with the Products including fitness, performance,
adequateness, safety, or quality, in the case of applications listed in from (1) to (11) written at the end of
this precautions, which may generally require high performance, function, quality, management of
production or safety.
Therefore, the Product shall be applied in compliance with the specific application.
WE DISCLAIM ANY LOSS AND DAMAGES ARISING FROM OR IN CONNECTION WITH THE
PRODUCTS INCLUDING BUT NOT LIMITED TO THE CASE SUCH LOSS AND DAMAGES CAUSED BY
THE UNEXPECTED ACCIDENT, IN EVENT THAT (i) THE PRODUCT IS APPLIED FOR THE PURPOSE
WHICH IS NOT SPECIFIED AS THE SPECIFIC APPLICATION FOR THE PRODUCT, AND/OR (ii) THE
PRODUCT IS APPLIED FOR ANY FOLLOWING APPLICATION PURPOSES FROM (1) TO (11) (EXCEPT
THAT SUCH APPLICATION PURPOSE IS UNAMBIGUOUSLY SPECIFIED AS SPECIFIC APPLICATION
FOR THE PRODUCT IN OUR CATALOG SPECIFICATION FORMS, DATASHEETS, OR OTHER
DOCUMENTS OFFICIALLY ISSUED BY US*)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Aircraft equipment
Aerospace equipment
Undersea equipment
Power plant control equipment
Medical equipment
Transportation equipment
Traffic control equipment
Disaster prevention/security equipment
Industrial data-processing equipment
Combustion/explosion control equipment
Equipment with complexity and/or required reliability equivalent to the applications listed in the above.
For exploring information of the Products which will be compatible with the particular purpose other than
those specified in the specification, please contact our sales offices, distribution agents, or trading
companies with which you make a deal, or via our web contact form.
Contact form: https://www.murata.com/contactform
*We may design and manufacture particular Products for applications listed in (1) to (11). Provided that,
in such case we shall unambiguously specify such Specific Application in the specification without any
exception.
Therefore, any other documents and/or performances, whether exist or non-exist, shall not be deemed as
the evidence to imply that we accept the applications listed in (1) to (11).
EGLEDMNO03A
3/23
Reference only
CAUTION
NOTICE
1. CLEANING (ULTRASONIC CLEANING)
To perform ultrasonic cleaning, observe the following conditions.
Rinse bath capacity : Output of 20 watts per liter or less.
Rinsing time : 5 min maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.
2. SOLDERING AND MOUNTING
Insertion of the Lead Wire
• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.
• Insert the lead wire into the PCB with a distance appropriate to the lead space.
3. CAPACITANCE CHANGE OF CAPACITORS
• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)
Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance
slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on
a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time
constant circuit.
Please contact us if you need a detail information.
NOTE
1. Please make sure that your product has been evaluated in view of your specifications with our product
being mounted to your product.
2. You are requested not to use our product deviating from this product specification.
EGLEDMNO03A
4/23
Reference only
1. Application
This product specification is applied to Leaded MLCC RCE series.
1. Specific applications:
･Automotive powertrain/safety equipment: Products that can be used for automotive equipment related to
running, turning, stopping, safety devices, etc., or equipment whose structure, equipment, and performance
are legally required to meet technical standards for safety assurance or environmental protection.
･Automotive infotainment/comfort equipment: Products that can be used for automotive equipment such as
car navigation systems and car audio systems that do not directly relate to human life and whose structure,
equipment, and performance are not specifically required by law to meet technical standards for safety
assurance or environmental protection.
･Medial Equipment [GHTF A/B/C] except for Implant Equipment: Products suitable for use in medical
devices designated under the GHTF international classifications as Class A or Class B (the functions of
which are not directly involved in protection of human life or property) or in medical devices other than
implants designated under the GHTF international classifications as Class C (the malfunctioning of which is
considered to pose a comparatively high risk to the human body).
2.Unsuitable Application: Applications listed in “Limitation of applications” in this product specification.
2. Rating
• Part Number Configuration
ex.)
RCE
Series
1E
226
M
W
M1
Temperature
R7
Rated
Capacitance
Capacitance
Dimension
Lead
Individual
Characteristics
Voltage
Style
Specification
Tolerance
(LxW)
• Temperature Characteristics
Code
Temp. Char.
C7
R7
• Rated Voltage
Code
1E
1H
2A
X7S
(EIA code)
X7R
(EIA code)
H03
A
Package
Temp. Range
Cap. Change
Standard
Temp.
Operating
Temp. Range
-55～125°C
+/-22%
25°C
-55～125°C
-55～125°C
+/-15%
25°C
-55～125°C
Rated voltage
DC25V
DC50V
DC100V
• Capacitance
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.
ex.) In case of 226 .
6
22 × 10 = 22000000 pF
• Capacitance Tolerance
Code
Capacitance Tolerance
K
+/-10%
M
+/-20%
• Dimension (LxW)
Please refer to [ Part number list ].
TEIKAKU
5/23
Reference only
• Lead Style
*Lead wire is "solder coated CP wire".
Code
Lead Style
A2
Straight type
A3
Straight type
DB
Straight taping type
DN
Straight taping type
K1
Inside crimp type
M1
Inside crimp taping type
Lead spacing (mm)
2.5+/-0.8
2.5+/-0.8
2.5+0.4/-0.2
2.5+0.4/-0.2
5.0+/-0.8
5.0+0.6/-0.2
• Individual Specification
Murata’s control code.
Please refer to [ Part number list ].
• Package
Code
A
B
Package
Taping type of Ammo
Bulk type
3. Marking
Temp. char.
Capacitance
Capacitance tolerance
Rated voltage
Company name code
(Ex.)
Rated voltage
Dimension code
0,1
:
:
:
:
Letter code : C (X7R/X7S Char. Except dimension code : 0,1)
3 digit numbers
Code
Letter code : 2 (DC25V. Except dimension code : 0,1)
Letter code : 5 (DC50V. Except dimension code : 0,1)
Letter code : 1 (DC100V. Except dimension code : 0,1)
: Abbreviation :
(Except dimension code : 0,1)
DC25V
DC50V
DC100V
105K
103K
104K
2
475
K2C
105
K5C
105
K1C
3,W
226
M2C
226
K5C
475
K1C
TEIKAKU
6/23
Reference only
4. Part number list
Unit : mm
Customer
Part Number
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
Lead Style (pcs)
RCER71E104K0A2H03B
X7R
25
0.1μF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71E154K0A2H03B
X7R
25
0.15μF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71E224K0A2H03B
X7R
25
0.22μF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71E334K1A2H03B
X7R
25
0.33μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71E474K1A2H03B
X7R
25
0.47μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71E684K1A2H03B
X7R
25
0.68μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71E105K1A2H03B
X7R
25
1.0μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71E155K2A2H03B
X7R
25
1.5μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71E225K2A2H03B
X7R
25
2.2μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71E335K2A2H03B
X7R
25
3.3μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71E475K2A2H03B
X7R
25
4.7μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71E106K3A2H03B
X7R
25
10μF
±10%
5.5
5.0
-
2.5
4.0
3A2
500
RCER71H221K0A2H03B
X7R
50
220pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H331K0A2H03B
X7R
50
330pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H471K0A2H03B
X7R
50
470pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H681K0A2H03B
X7R
50
680pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H102K0A2H03B
X7R
50
1000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H152K0A2H03B
X7R
50
1500pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H222K0A2H03B
X7R
50
2200pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H332K0A2H03B
X7R
50
3300pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H472K0A2H03B
X7R
50
4700pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H682K0A2H03B
X7R
50
6800pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H103K0A2H03B
X7R
50
10000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H153K0A2H03B
X7R
50
15000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H223K0A2H03B
X7R
50
22000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H333K0A2H03B
X7R
50
33000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H473K0A2H03B
X7R
50
47000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H683K0A2H03B
X7R
50
68000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H104K0A2H03B
X7R
50
0.1μF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER71H154K1A2H03B
X7R
50
0.15μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71H224K1A2H03B
X7R
50
0.22μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71H334K1A2H03B
X7R
50
0.33μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71H474K1A2H03B
X7R
50
0.47μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71H684K2A2H03B
X7R
50
0.68μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCEC71H105K1A2H03B
X7S
50
1.0μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER71H105K2A2H03B
X7R
50
1.0μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71H155K2A2H03B
X7R
50
1.5μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71H225K2A2H03B
X7R
50
2.2μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER71H335K3A2H03B
X7R
50
3.3μF
±10%
5.5
5.0
-
2.5
4.0
3A2
500
RCEC71H475K2A2H03B
X7S
50
4.7μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
PNLIST
7/23
Reference only
Unit : mm
Customer
Part Number
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
Lead Style (pcs)
RCER71H475K3A2H03B
X7R
50
4.7μF
±10%
5.5
5.0
-
2.5
4.0
3A2
500
RCEC71H106K3A2H03B
X7S
50
10μF
±10%
5.5
5.0
-
2.5
4.0
3A2
500
RCER72A221K0A2H03B
X7R
100
220pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A331K0A2H03B
X7R
100
330pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A471K0A2H03B
X7R
100
470pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A681K0A2H03B
X7R
100
680pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A102K0A2H03B
X7R
100
1000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A152K0A2H03B
X7R
100
1500pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A222K0A2H03B
X7R
100
2200pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A332K0A2H03B
X7R
100
3300pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A472K0A2H03B
X7R
100
4700pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A682K0A2H03B
X7R
100
6800pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A103K0A2H03B
X7R
100
10000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A153K0A2H03B
X7R
100
15000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A223K0A2H03B
X7R
100
22000pF
±10%
3.6
3.5
-
2.5
2.5
0A2
500
RCER72A333K1A2H03B
X7R
100
33000pF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER72A473K1A2H03B
X7R
100
47000pF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER72A683K1A2H03B
X7R
100
68000pF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER72A104K1A2H03B
X7R
100
0.1μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER72A154K2A2H03B
X7R
100
0.15μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER72A224K2A2H03B
X7R
100
0.22μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER72A334K1A2H03B
X7R
100
0.33μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER72A474K2A2H03B
X7R
100
0.47μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCER72A684K2A2H03B
X7R
100
0.68μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCEC72A105K1A2H03B
X7S
100
1.0μF
±10%
4.0
3.5
-
2.5
2.5
1A2
500
RCER72A105K2A2H03B
X7R
100
1.0μF
±10%
5.5
4.0
-
2.5
3.15
2A2
500
RCEC72A155K3A2H03B
X7S
100
1.5μF
±10%
5.5
5.0
-
2.5
4.0
3A2
500
RCEC72A225K2A3H03B
X7S
100
2.2μF
±10%
5.5
4.0
6.0
2.5
3.15
2A3
500
RCEC72A225K3A2H03B
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0
3A2
500
RCEC72A475K3A3H03B
X7S
100
4.7μF
±10%
5.5
5.0
7.5
2.5
4.0
3A3
500
PNLIST
8/23
Reference only
Unit : mm
Customer
Part Number
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
Lead Style (pcs)
RCER71E104K0K1H03B
X7R
25
0.1μF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71E154K0K1H03B
X7R
25
0.15μF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71E224K0K1H03B
X7R
25
0.22μF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71E334K1K1H03B
X7R
25
0.33μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71E474K1K1H03B
X7R
25
0.47μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71E684K1K1H03B
X7R
25
0.68μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71E105K1K1H03B
X7R
25
1.0μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71E155K2K1H03B
X7R
25
1.5μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71E225K2K1H03B
X7R
25
2.2μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71E335K2K1H03B
X7R
25
3.3μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71E475K2K1H03B
X7R
25
4.7μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71E106K3K1H03B
X7R
25
10μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
RCER71E226MWK1H03B
X7R
25
22μF
±20%
5.5
7.5
10.0
5.0
4.0
WK1
500
RCER71H221K0K1H03B
X7R
50
220pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H331K0K1H03B
X7R
50
330pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H471K0K1H03B
X7R
50
470pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H681K0K1H03B
X7R
50
680pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H102K0K1H03B
X7R
50
1000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H152K0K1H03B
X7R
50
1500pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H222K0K1H03B
X7R
50
2200pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H332K0K1H03B
X7R
50
3300pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H472K0K1H03B
X7R
50
4700pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H682K0K1H03B
X7R
50
6800pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H103K0K1H03B
X7R
50
10000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H153K0K1H03B
X7R
50
15000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H223K0K1H03B
X7R
50
22000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H333K0K1H03B
X7R
50
33000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H473K0K1H03B
X7R
50
47000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H683K0K1H03B
X7R
50
68000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H104K0K1H03B
X7R
50
0.1μF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER71H154K1K1H03B
X7R
50
0.15μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71H224K1K1H03B
X7R
50
0.22μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71H334K1K1H03B
X7R
50
0.33μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71H474K1K1H03B
X7R
50
0.47μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71H684K2K1H03B
X7R
50
0.68μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCEC71H105K1K1H03B
X7S
50
1.0μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER71H105K2K1H03B
X7R
50
1.0μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71H155K2K1H03B
X7R
50
1.5μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71H225K2K1H03B
X7R
50
2.2μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71H335K3K1H03B
X7R
50
3.3μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
PNLIST
9/23
Reference only
Unit : mm
Customer
Part Number
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
Lead Style (pcs)
RCEC71H475K2K1H03B
X7S
50
4.7μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER71H475K3K1H03B
X7R
50
4.7μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
RCEC71H106K3K1H03B
X7S
50
10μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
RCER71H106MWK1H03B
X7R
50
10μF
±20%
5.5
7.5
10.0
5.0
4.0
WK1
500
RCEC71H226MWK1H03B
X7S
50
22μF
±20%
5.5
7.5
10.0
5.0
4.0
WK1
500
RCER72A221K0K1H03B
X7R
100
220pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A331K0K1H03B
X7R
100
330pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A471K0K1H03B
X7R
100
470pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A681K0K1H03B
X7R
100
680pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A102K0K1H03B
X7R
100
1000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A152K0K1H03B
X7R
100
1500pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A222K0K1H03B
X7R
100
2200pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A332K0K1H03B
X7R
100
3300pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A472K0K1H03B
X7R
100
4700pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A682K0K1H03B
X7R
100
6800pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A103K0K1H03B
X7R
100
10000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A153K0K1H03B
X7R
100
15000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A223K0K1H03B
X7R
100
22000pF
±10%
3.6
3.5
6.0
5.0
2.5
0K1
500
RCER72A333K1K1H03B
X7R
100
33000pF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER72A473K1K1H03B
X7R
100
47000pF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER72A683K1K1H03B
X7R
100
68000pF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER72A104K1K1H03B
X7R
100
0.1μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER72A154K2K1H03B
X7R
100
0.15μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER72A224K2K1H03B
X7R
100
0.22μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER72A334K1K1H03B
X7R
100
0.33μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER72A474K2K1H03B
X7R
100
0.47μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCER72A684K2K1H03B
X7R
100
0.68μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCEC72A105K1K1H03B
X7S
100
1.0μF
±10%
4.0
3.5
5.0
5.0
2.5
1K1
500
RCER72A105K2K1H03B
X7R
100
1.0μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCEC72A155K3K1H03B
X7S
100
1.5μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
RCEC72A225K2K1H03B
X7S
100
2.2μF
±10%
5.5
4.0
6.0
5.0
3.15
2K1
500
RCEC72A225K3K1H03B
X7S
100
2.2μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
RCEC72A475K3K1H03B
X7S
100
4.7μF
±10%
5.5
5.0
7.5
5.0
4.0
3K1
500
RCEC72A475MWK1H03B
X7S
100
4.7μF
±20%
5.5
7.5
10.0
5.0
4.0
WK1
500
PNLIST
10/23
Reference only
Unit : mm
Customer
Part Number
PNLIST
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
H/H0 Lead Style (pcs)
RCER71E104K0DBH03A
X7R
25
0.1μF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71E154K0DBH03A
X7R
25
0.15μF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71E224K0DBH03A
X7R
25
0.22μF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71E334K1DBH03A
X7R
25
0.33μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71E474K1DBH03A
X7R
25
0.47μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71E684K1DBH03A
X7R
25
0.68μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71E105K1DBH03A
X7R
25
1.0μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71E155K2DBH03A
X7R
25
1.5μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71E225K2DBH03A
X7R
25
2.2μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71E335K2DBH03A
X7R
25
3.3μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71E475K2DBH03A
X7R
25
4.7μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71E106K3DBH03A
X7R
25
10μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCER71H221K0DBH03A
X7R
50
220pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H331K0DBH03A
X7R
50
330pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H471K0DBH03A
X7R
50
470pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H681K0DBH03A
X7R
50
680pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H102K0DBH03A
X7R
50
1000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H152K0DBH03A
X7R
50
1500pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H222K0DBH03A
X7R
50
2200pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H332K0DBH03A
X7R
50
3300pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H472K0DBH03A
X7R
50
4700pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H682K0DBH03A
X7R
50
6800pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H103K0DBH03A
X7R
50
10000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H153K0DBH03A
X7R
50
15000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H223K0DBH03A
X7R
50
22000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H333K0DBH03A
X7R
50
33000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H473K0DBH03A
X7R
50
47000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H683K0DBH03A
X7R
50
68000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H104K0DBH03A
X7R
50
0.1μF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER71H154K1DBH03A
X7R
50
0.15μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71H224K1DBH03A
X7R
50
0.22μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71H334K1DBH03A
X7R
50
0.33μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71H474K1DBH03A
X7R
50
0.47μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71H684K2DBH03A
X7R
50
0.68μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCEC71H105K1DBH03A
X7S
50
1.0μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER71H105K2DBH03A
X7R
50
1.0μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71H155K2DBH03A
X7R
50
1.5μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71H225K2DBH03A
X7R
50
2.2μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER71H335K3DBH03A
X7R
50
3.3μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC71H475K2DBH03A
X7S
50
4.7μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
11/23
Reference only
Unit : mm
Customer
Part Number
PNLIST
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
H/H0 Lead Style (pcs)
RCER71H475K3DBH03A
X7R
50
4.7μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC71H106K3DBH03A
X7S
50
10μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCER72A221K0DBH03A
X7R
100
220pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A331K0DBH03A
X7R
100
330pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A471K0DBH03A
X7R
100
470pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A681K0DBH03A
X7R
100
680pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A102K0DBH03A
X7R
100
1000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A152K0DBH03A
X7R
100
1500pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A222K0DBH03A
X7R
100
2200pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A332K0DBH03A
X7R
100
3300pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A472K0DBH03A
X7R
100
4700pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A682K0DBH03A
X7R
100
6800pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A103K0DBH03A
X7R
100
10000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A153K0DBH03A
X7R
100
15000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A223K0DBH03A
X7R
100
22000pF
±10%
3.6
3.5
-
2.5
2.5 16.0
0DB
2000
RCER72A333K1DBH03A
X7R
100
33000pF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER72A473K1DBH03A
X7R
100
47000pF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER72A683K1DBH03A
X7R
100
68000pF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER72A104K1DBH03A
X7R
100
0.1μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER72A154K2DBH03A
X7R
100
0.15μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER72A224K2DBH03A
X7R
100
0.22μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER72A334K1DBH03A
X7R
100
0.33μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER72A474K2DBH03A
X7R
100
0.47μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCER72A684K2DBH03A
X7R
100
0.68μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCEC72A105K1DBH03A
X7S
100
1.0μF
±10%
4.0
3.5
-
2.5
2.5 16.0
1DB
2000
RCER72A105K2DBH03A
X7R
100
1.0μF
±10%
5.5
4.0
-
2.5 3.15 16.0
2DB
2000
RCEC72A155K3DBH03A
X7S
100
1.5μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A225K2DNH03A
X7S
100
2.2μF
±10%
5.5
4.0
6.0
2.5 3.15 16.0
2DN
2000
RCEC72A225K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A230K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A231K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A232K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A233K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A234K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A235K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A236K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A237K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A238K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A239K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
RCEC72A240K3DBH03A
X7S
100
2.2μF
±10%
5.5
5.0
-
2.5
4.0 16.0
3DB
1500
12/23
Reference only
Unit : mm
Customer
Part Number
PNLIST
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
H/H0 Lead Style (pcs)
RCEC72A475K3DNH03A
X7S
100
4.7μF
±10%
5.5
5.0
7.5
2.5
4.0 16.0
3DN
2000
RCER71E104K0M1H03A
X7R
25
0.1μF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71E154K0M1H03A
X7R
25
0.15μF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71E224K0M1H03A
X7R
25
0.22μF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71E334K1M1H03A
X7R
25
0.33μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71E474K1M1H03A
X7R
25
0.47μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71E684K1M1H03A
X7R
25
0.68μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71E105K1M1H03A
X7R
25
1.0μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71E155K2M1H03A
X7R
25
1.5μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71E225K2M1H03A
X7R
25
2.2μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71E335K2M1H03A
X7R
25
3.3μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71E475K2M1H03A
X7R
25
4.7μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71E106K3M1H03A
X7R
25
10μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
1500
RCER71E226MWM1H03A X7R
25
22μF
±20%
5.5
7.5 10.0
5.0
4.0 16.0
WM1
1500
RCER71H221K0M1H03A
X7R
50
220pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H331K0M1H03A
X7R
50
330pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H471K0M1H03A
X7R
50
470pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H681K0M1H03A
X7R
50
680pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H102K0M1H03A
X7R
50
1000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H152K0M1H03A
X7R
50
1500pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H222K0M1H03A
X7R
50
2200pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H332K0M1H03A
X7R
50
3300pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H472K0M1H03A
X7R
50
4700pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H682K0M1H03A
X7R
50
6800pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H103K0M1H03A
X7R
50
10000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H153K0M1H03A
X7R
50
15000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H223K0M1H03A
X7R
50
22000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H333K0M1H03A
X7R
50
33000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H473K0M1H03A
X7R
50
47000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H683K0M1H03A
X7R
50
68000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H104K0M1H03A
X7R
50
0.1μF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER71H154K1M1H03A
X7R
50
0.15μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71H224K1M1H03A
X7R
50
0.22μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71H334K1M1H03A
X7R
50
0.33μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71H474K1M1H03A
X7R
50
0.47μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71H684K2M1H03A
X7R
50
0.68μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCEC71H105K1M1H03A
X7S
50
1.0μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER71H105K2M1H03A
X7R
50
1.0μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71H155K2M1H03A
X7R
50
1.5μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71H225K2M1H03A
X7R
50
2.2μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
13/23
Reference only
Unit : mm
Customer
Part Number
PNLIST
Murata Part Number
T.C.
DC
Rated
Volt.
(V)
Cap.
Cap.
Tol.
Dimension (mm)
L
W
W1
F
T
Dimension Pack
qty.
(LxW)
H/H0 Lead Style (pcs)
RCER71H335K3M1H03A
X7R
50
3.3μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
1500
RCEC71H475K2M1H03A
X7S
50
4.7μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER71H475K3M1H03A
X7R
50
4.7μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
1500
RCEC71H106K3M1H03A
X7S
50
10μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
1500
RCER71H106MWM1H03A X7R
50
10μF
±20%
5.5
7.5 10.0
5.0
4.0 16.0
WM1
1500
RCEC71H226MWM1H03A X7S
50
22μF
±20%
5.5
7.5 10.0
5.0
4.0 16.0
WM1
1500
RCER72A221K0M1H03A
X7R
100
220pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A331K0M1H03A
X7R
100
330pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A471K0M1H03A
X7R
100
470pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A681K0M1H03A
X7R
100
680pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A102K0M1H03A
X7R
100
1000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A152K0M1H03A
X7R
100
1500pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A222K0M1H03A
X7R
100
2200pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A332K0M1H03A
X7R
100
3300pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A472K0M1H03A
X7R
100
4700pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A682K0M1H03A
X7R
100
6800pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A103K0M1H03A
X7R
100
10000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A153K0M1H03A
X7R
100
15000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A223K0M1H03A
X7R
100
22000pF
±10%
3.6
3.5
6.0
5.0
2.5 16.0
0M1
2000
RCER72A333K1M1H03A
X7R
100
33000pF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER72A473K1M1H03A
X7R
100
47000pF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER72A683K1M1H03A
X7R
100
68000pF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER72A104K1M1H03A
X7R
100
0.1μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER72A154K2M1H03A
X7R
100
0.15μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER72A224K2M1H03A
X7R
100
0.22μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER72A334K1M1H03A
X7R
100
0.33μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER72A474K2M1H03A
X7R
100
0.47μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCER72A684K2M1H03A
X7R
100
0.68μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCEC72A105K1M1H03A
X7S
100
1.0μF
±10%
4.0
3.5
5.0
5.0
2.5 16.0
1M1
2000
RCER72A105K2M1H03A
X7R
100
1.0μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCEC72A155K3M1H03A
X7S
100
1.5μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
1500
RCEC72A225K2M1H03A
X7S
100
2.2μF
±10%
5.5
4.0
6.0
5.0 3.15 16.0
2M1
2000
RCEC72A225K3M1H03A
X7S
100
2.2μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
1500
RCEC72A475K3M1H03A
X7S
100
4.7μF
±10%
5.5
5.0
7.5
5.0
4.0 16.0
3M1
2000
RCEC72A475MWM1H03A X7S
100
4.7μF
±20%
5.5
7.5 10.0
5.0
4.0 16.0
WM1
1500
14/23
Reference only
5. Specification
Test Item
No.
1
Specification
Test Method (Compliant Standard:AEC-Q200)
Pre-and Post-Stress
-
Electrical Test
2
High
Appearance
No defects or abnormalities
Sit the capacitor for 1000±12h at 150±3°C. Let sit for 24±2h at
Temperature
Capacitance
within ±12.5%
*room condition then measure.
Exposure
Change
(Storage)
D.F.
0.04 max. * 1
Perform the heat treatment at 150+0/-10°C for 60±5 min and
I.R.
More than 1,000MΩ or 50 MΩ・µF
then let sit for 24±2 h at *room condition.
•Pretreatment
(Whichever is smaller)
3
Temperature
Appearance
No defects or abnormalities
Perform the 1000 cycles according to the four heat treatments
Cycling
Capacitance
within ±12.5%
listed in the following table. Let sit for 24±2 h at *room condition,
Change
then measure.
D.F.
0.05 max. * 1
I.R.
1,000MΩ or 50MΩ・µF min.
(Whichever is smaller)
Step
1
2
3
4
Temp.
(°C)
-55+0/-3
Room
Temp.
125+3/-0
Room
Temp.
Time
(min.)
15±3
1
15±3
1
•Pretreatment
Perform the heat treatment at 150+0/-10°C for 60±5 min and
then let sit for 24±2 h at *room condition.
4
Moisture
Appearance
No defects or abnormalities
Apply the 24h heat (25 to 65°C) and humidity (80 to 98%)
Resistance
Capacitance
within ±12.5%
treatment shown below, 10 consecutive times.
Change
Let sit for 24±2 h at *room condition, then measure.
D.F.
0.05 max. * 1
I.R.
500MΩ or 25MΩ・µF min.
(Whichever is smaller)
•Pretreatment
Perform the heat treatment at 150+0/-10°C for 60±5 min and
then let sit for 24±2 h at *room condition.
5
Biased
Appearance
No defects or abnormalities
Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor)
Humidity
Capacitance
within ±12.5% * 2
at 85±3°C and 80 to 85% humidity for 1000±12h.
Change
Remove and let sit for 24±2 h at *room condition, then measure.
D.F.
0.05 max. * 1
The charge/discharge current is less than 50mA.
I.R.
500MΩ or 25MΩ・µF min. * 3
•Pretreatment
(Whichever is smaller)
Perform the heat treatment at 150+0/-10°C for 60±5 min and
then let sit for 24±2 h at *room condition.
6
Operational
Appearance
No defects or abnormalities
Apply 200% of the rated voltage * 5 for 1000±12h at 125±3°C.
Life
Capacitance
within ±12.5% * 2
Let sit for 24±2 h at *room condition, then measure.
Change
The charge/discharge current is less than 50mA.
D.F.
0.04 max. * 1
•Pretreatment
I.R.
1,000MΩ or 50MΩ・µF min. * 4
Apply test voltage for 60±5 min at test temperature.
(Whichever is smaller)
Remove and let sit for 24±2 h at *room condition.
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa
* 5 Below parts are applicable in rated voltage×150%.
Below parts are applicable in
* 1 D.F. : 0.2 max..
* 2 Capacitance Change : within ±15%
* 3 I.R. : 12.5MΩ・µF min.
* 4 I.R. : 25MΩ・µF min.
Char.
Rated Voltage
Capacitance
Dimensions
C7
2A
105
1
C7
2A
225
2
C7
2A
475
3
ESRCE01G
15/23
Char.
Rated Voltage
Capacitance
Dimensions
C7
1H
105
1
C7
1H
475
2
C7
1H
106
3
C7
1H
226
W
R7
2A
334
1
R7
2A
474-105
2
C7
2A
105
1
C7
2A
225
2
C7
2A
155-475
3
C7
2A
475
W
Reference only
Test Item
No.
Specification
Test Method (Compliant Standard:AEC-Q200)
7
External Visual
No defects or abnormalities
Visual inspection
8
Physical Dimension
Within the specified dimensions
Using calipers and micrometers.
9
Marking
To be easily legible.
Visual inspection
10
Resistance
Appearance
No defects or abnormalities
Per MIL-STD-202 Method 215
to Solvents
Capacitance
Within the specified tolerance
D.F.
0.025 max. * 6
I.R.
More than 10,000MΩ or 500 MΩ・µF * 7
Solvent 1 : 1 part (by volume) of isopropyl alcohol
3 parts (by volume) of mineral spirits
(Whichever is smaller)
Solvent 2 : Terpene defluxer
Solvent 3 : 42 parts (by volume) of water
1part (by volume) of propylene glycol
monomethyl ether
1 part (by volume) of monoethanolamine
11
Mechanical
Appearance
No defects or abnormalities
Three shocks in each direction should be applied along 3
Shock
Capacitance
Within the specified tolerance
mutually perpendicular axes of the test specimen (18 shocks).
D.F.
0.025 max. * 6
The specified test pulse should be Half-sine and should have a
duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s.
12
Vibration
Appearance
No defects or abnormalities
The capacitor should be subjected to a simple harmonic motion
Capacitance
Within the specified tolerance
having a total amplitude of 1.5mm, the frequency being varied
D.F.
0.025 max. * 6
uniformly between the approximate limits of 10 and 2,000Hz.
The frequency range, from 10 to 2000Hz and return to 10Hz,
should be traversed in approximately 20 min. This motion
should be applied for 12 items in each 3 mutually perpendicular
directions (total of 36 times).
13-1 Resistance
Appearance
No defects or abnormalities
The lead wires should be immersed in the melted solder 1.5 to
to Soldering
Capacitance
Within ±7.5% * 8
2.0mm from the root of terminal at 260±5°C for 10±1 seconds.
Heat
Change
(Non-
Dielectric
No defects
• Pre-treatment
Preheat)
Strength
Capacitor should be stored at 150+0/-10°C for one
(Between
hour, then place at *room condition for 24±2 hours before initial
terminals)
measurement.
• Post-treatment
Capacitor should be stored for 24±2 hours at *room condition.
13-2 Resistance
Appearance
No defects or abnormalities
First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.
to Soldering
Capacitance
Within ±7.5% * 8
Then, the lead wires should be immersed in the melted solder
Heat
Change
(On-
Dielectric
Preheat)
Strength
• Pre-treatment
(Between
Capacitor should be stored at 150+0/-10°C for one
1.5 to 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.
No defects
terminals)
hour, then place at *room condition for 24±2 hours before initial
measurement.
• Post-treatment
Capacitor should be stored for 24±2 hours at *room condition.
13-3 Resistance
Appearance
No defects or abnormalities
Test condition
to Soldering
Capacitance
Within ±7.5% * 8
Heat
Change
(soldering
Dielectric
iron method)
Strength
Straight Lead : 1.5 to 2.0mm from the root of terminal.
(Between
Crimp Lead
Temperature of iron-tip : 350±10°C
Soldering time
No defects
: 3.5±0.5 seconds
Soldering position
: 1.5 to 2.0mm from the end of lead bend.
terminals)
• Pre-treatment
Capacitor should be stored at 150+0/-10°C for one
hour, then place at *room condition for 24±2 hours before initial
measurement.
• Post-treatment
Capacitor should be stored for 24±2 hours at *room condition.
14
Thermal
Appearance
No defects or abnormalities
Perform the 300 cycles according to the two heat treatments listed
Shock
Capacitance
within ±12.5%
in the following table(Maximum transfer time is 20s.). Let sit for
Change
24±2 h at *room condition, then measure.
D.F.
0.05 max. * 1
I.R.
1,000MΩ or 50MΩ・µF min.
(Whichever is smaller)
•Pretreatment
Step
1
2
Temp.
(°C)
-55+0/-3
125+3/-0
Time
(min.)
15±3
15±3
Perform the heat treatment at 150+0/-10°C for 60±5 min and
then let sit for 24±2 h at *room condition.
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa
Below parts are applicable in
* 1 D.F. : 0.2 max..
* 6 D.F. : 0.125 max..
* 7 I.R. : 50 MΩ・µF min.
* 8 Capacitance Change : within ±10%
ESRCE01G
Char.
Rated Voltage
Capacitance
C7
2A
105
Dimensions
1
C7
2A
225
2
C7
2A
475
3
16/23
Reference only
Test Item
No.
15
ESD
Specification
Test Method (Compliant Standard:AEC-Q200)
Appearance
No defects or abnormalities
Capacitance
Within the specified tolerance
D.F.
0.025 max. * 6
I.R.
More than 10,000MΩ or 500 MΩ・µF * 7
Per AEC-Q200-002
(Whichever is smaller)
16
Solderability
Lead wire should be soldered with uniform
Should be placed into steam aging for 8h±15 min.
coating on the axial direction over 95%
The terminal of capacitor is dipped into a solution of rosin
of the circumferential direction.
ethanol (25% rosin in weight propotion).
Immerse in solder solution for 2±0.5 seconds.
In both cases the depth of dipping is up to about 1.5 to 2mm from
the terminal body.
Temp. of solder : 245±5°C (Sn-3.0Ag-0.5Cu)
17
Electrical
Appearance
No defects or abnormalities
Visual inspection.
Characte-
Capacitance
Within the specified tolerance
The capacitance/D.F. should be measured at 25°C at the frequency
rization
D.F.
0.025 max. * 6
and voltage shown in the table.
I.R.
Between
Nominal Cap.
Frequency
Voltage
C≦10μF
1±0.1kHz
AC1±0.2V (r.m.s.)
C＞10μF
120±24Hz
AC0.5±0.1V (r.m.s.)
10,000MΩ or 500MΩ・µF min. * 7 The insulation resistance should be measured with a DC voltage
Terminals (Whichever is smaller)
not exceeding the rated voltage at 25 °C within 2 min. of charging.
Dielectric
Between
The capacitor should not be damaged when DC voltage of 250%
Strength
Terminals
No defects or abnormalities
of the rated voltage * 9 is applied between the terminations for 1 to 5
seconds.
(Charge/Discharge current ≦ 50mA.)
Terminal
To
External
Resin
No defects or abnormalities
The capacitor is placed in a container with metal balls of 1mm
diameter so that each terminal, short-circuit is kept approximately
2mm from the balls, and 250% of the rated DC voltage is impressed
for 1 to 5 seconds between capacitor terminals and metal balls.
(Charge/Discharge current ≦ 50mA.)
18
Terminal
Tensile
Strength
Strength
Termination not to be broken or loosened
As in the figure, fix the capacitor body, apply the force gradually
to each lead in the radial direction of the capacitor until reaching
10N and then keep the force applied for 10±1 seconds.
F
Termination not to be broken or loosened
Bending
Strength
Each lead wire should be subjected to a force of 2.5N and then
be bent 90° at the point of egress in one direction. Each wire is
then returned to the original position and bent 90° in the opposite
direction at the rate of one bend per 2 to 3 seconds.
19
Capacitance
Char.X7R : Within ±15%
The capacitance change should be measured after 5min.
Temperature
Char.X7S : Within ±22%
at each specified temperature step.
Characteristics
Step
Temperature(°C)
1
25±2
2
-55±3
3
25±2
4
125±3
5
25±2
The ranges of capacitance change compared with the above
25°C value over the temperature ranges shown in the table
should be within the specified ranges.
•Pretreatment
Perform the heat treatment at 150+0/-10°C for 60±5 min and
then let sit for 24±2 h at *room condition.
Perform the initial measurement.
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa
Below parts are applicable in
* 6 D.F. : 0.125 max..
* 7 I.R. : 50 MΩ・µF min.
* 9 Rated voltage×200%
ESRCE01G
Rated Voltage
Capacitance
Dimensions
C7
2A
105
1
C7
2A
225
2
C7
2A
475
3
17/23
Reference only
6. Packing specification
・Bulk type (Packing style code : B)
The size of packing case and packing way
Plastic bag
Partition
270 max.
125 max.
Unit : mm
340 max.
The number of packing =
*1
Packing quantity × *2 n
*1 : Please refer to [Part number list].
*2 : Standard n = 20 (bag)
Note)
The outer package and the number of outer packing be changed by the order getting amount.
JKBCRPE02
18/23
Reference only
・Ammo pack taping type (Packing style code : A)
A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.
When body of the capacitor is piled on other body under it.
The size of packing case and packing way
240 max.
Position of label
340 max.
Unit : mm
51 max.
Hold down tape
Capacitor
Base tape
Hold down
tape upper
EKTRPE01
19/23
Reference only
7. Taping specification
7-1. Dimension of capacitors on tape
Straight taping type < Lead Style : DB >
Pitch of component 12.7mm / Lead spacing 2.5mm
P
P2
△h1
0 △h2
△S
Marking
W2
Φd
t1
t2
W
W0
L
ΦD0
W1
F
H
e
P1
P0
Unit : mm
Item
Code
Dimensions
Pitch of component
P
12.7+/-1.0
Pitch of sprocket hole
P0
12.7+/-0.2
F
2.5+0.4/-0.2
Length from hole center to component
center
P2
6.35+/-1.3
Length from hole center to lead
P1
5.1+/-0.7
Deviation along tape, left or right defect
ΔS
0+/-2.0
Carrier tape width
W
18.0+/-0.5
Position of sprocket hole
W1
9.0+0/-0.5
H
16.0+/-0.5
ΦD0
4.0+/-0.1
Lead diameter
Φd
0.5+/-0.05
Total tape thickness
t1
0.6+/-0.3
t2
1.5 max.
Lead spacing
Lead distance between reference and
bottom plane
Protrusion length
Diameter of sprocket hole
Total thickness of tape and lead wire
Deviation across tape
Portion to cut in case of defect
Deviation of progress direction
They include deviation by lead bend
Deviation of tape width direction
0.5 max.
Δh1
1.0 max.
Δh2
L
11.0+0/-1.0
Hold down tape width
W0
9.5 min.
Hold down tape position
W2
1.5+/-1.5
e
1.5 max.
Coating extension on lead
Remarks
ETP1DB02A
20/23
They include hold down tape
thickness
Reference only
Straight taping type < Lead Style : DN >
Pitch of component 12.7mm / Lead spacing 2.5mm
P
P2
∆h1
0
∆S
∆h2
Marking
t1
t2
W
W0
φ D0
W1
H0
φd
F
L
P1
W2
e
P0
Unit : mm
Code
Dimensions
Pitch of component
Item
P
12.7+/-1.0
Pitch of sprocket hole
P0
12.7+/-0.2
Lead spacing
F
2.5+0.4/-0.2
Length from hole center to component
center
P2
6.35+/-1.3
Length from hole center to lead
P1
5.1+/-0.7
Deviation along tape, left or right defect
ΔS
0+/-2.0
Carrier tape width
W
18.0+/-0.5
Position of sprocket hole
W1
9.0+0/-0.5
Lead distance between reference and
bottom plane
H0
16.0+/-0.5
Protrusion length
Diameter of sprocket hole
4.0+/-0.1
Lead diameter
Φd
0.5+/-0.05
Total tape thickness
t1
0.6+/-0.3
Total thickness of tape and lead wire
t2
1.5 max.
Portion to cut in case of defect
Δh1
They include deviation by lead bend
Deviation of tape width direction
L
11.0+0/-1.0
W0
9.5 min.
Hold down tape position
W2
1.5+/-1.5
e
They include hold down tape
thickness
1.0 max.
Δh2
Hold down tape width
Coating extension on lead
Deviation of progress direction
0.5 max.
ΦD0
Deviation across tape
Remarks
Up to the end of crimp
ETP1DN01
21/23
Reference only
Inside crimp taping type < Lead Style : M1 >
Pitch of component 12.7mm / Lead spacing 5.0mm
P2
P
Δh1
0
Δh2
ΔS
Marking
t1
t2
W0
L
ΦD0
W
Φd
W1
F
W2
P1
H0
e
P0
Unit : mm
Item
Code
Dimensions
Pitch of component
P
12.7+/-1.0
Pitch of sprocket hole
P0
12.7+/-0.2
F
5.0+0.6/-0.2
P2
6.35+/-1.3
Length from hole center to lead
P1
3.85+/-0.7
Deviation along tape, left or right defect
ΔS
0+/-2.0
Carrier tape width
W
18.0+/-0.5
Position of sprocket hole
W1
9.0+0/-0.5
Lead distance between reference and
bottom plane
H0
16.0+/-0.5
Lead spacing
Length from hole center to component
center
Protrusion length
Diameter of sprocket hole
ΦD0
4.0+/-0.1
Φd
0.5+/-0.05
Total tape thickness
t1
0.6+/-0.3
t2
1.5 max.
Deviation across tape
Portion to cut in case of defect
They include deviation by lead bend
Deviation of tape width direction
They include hold down tape
thickness
Δh1 2.0 max. (Dimension code : W)
Δh2 1.0 max. (except as above)
L
11.0+0/-1.0
Hold down tape width
W0
9.5 min.
Hold down tape position
W2
1.5+/-1.5
Coating extension on lead
Deviation of progress direction
0.5 max.
Lead diameter
Total thickness of tape and lead wire
Remarks
e
Up to the end of crimp
ETP1M101A
22/23
Reference only
7-2. Splicing way of tape
1) Adhesive force of tape is over 3N at test condition as below.
W
Hold down tape
Base tape
2) Splicing of tape
a) When base tape is spliced
•Base tape shall be spliced by cellophane tape.
(Total tape thickness shall be less than 1.05mm.)
Progress direction
in production line
Hold down tape
Base tape
No lifting for the
direction of
progressing
About 30 to 50
Cellophane tape
Unit : mm
b) When hold down tape is spliced
•Hold down tape shall be spliced with overlapping.
(Total tape thickness shall be less than 1.05mm.)
20 to 30
Progress direction
in production line
Hold down tape
Base tape
Unit : mm
c) When both tape are spliced
•Base tape and hold down tape shall be spliced with splicing tape.
ETP2R01
23/23
工商网监
湘ICP备2023018690号
