RCER72J103K2K1H03B

Reference Specification Leaded MLCC for Automotive with AEC-Q200 RCE Series Product specifications in this catalog are as of Apr. 2022, and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering.Please read rating and Cautions first. Reference only 䚷䚷䚷CAUTION 䚷䚷1. OPERATING VOLTAGE When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage containing these irregular voltage. When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter), be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or impulse withstand established for each equipment should be taken into considerations. Voltage Positional Measurement DC Voltage Vo-p DC+AC Voltage Vo-p AC Voltage Vp-p Pulse Voltage(1) Vp-p Pulse Voltage(2) Vp-p 䚷䚷2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.), applied voltage should be the load such as self-generated heat is within 20 °C on the condition of atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1 capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s characteristics and reliability. 䚷䚷3. FAIL-SAFE Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. 䚷䚷4. OPERATING AND STORAGE ENVIRONMENT The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months. 䚷䚷5. VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use. 䚷䚷6. SOLDERING When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. 䚷䚷7. BONDING AND RESIN MOLDING, RESIN COAT In case of bonding, molding or coating this product, verify that these processes do not affect the quality of capacitor by testing the performance of a bonded or molded product in the intended equipment. In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short circuit. The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or ceramic element cracking of a capacitor in a temperature cycling. 䚷䚷8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile. So please be careful not to give it mechanical stress. EGLEDMNO03 1/18 Reference only Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. 䚷䚷9. LIMITATION OF APPLICATIONS Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party’s life, body or property. 1. Aircraft equipment 2. Aerospace equipment 3. Undersea equipment 4. Power plant control equipment 5. Medical equipment 6. Transportation equipment (vehicles, trains, ships, etc.) 7. Traffic signal equipment 8. Disaster prevention / crime prevention equipment 9. Data-processing equipment exerting influence on public 10. Application of similar complexity and/or reliability requirements to the applications listed in the above. NOTICE 䚷䚷1. CLEANING (ULTRASONIC CLEANING) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity : Output of 20 watts per liter or less. Rinsing time : 5 min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 䚷䚷2. SOLDERING AND MOUNTING Insertion of the Lead Wire • When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire. • Insert the lead wire into the PCB with a distance appropriate to the lead space. 䚷䚷3. CAPACITANCE CHANGE OF CAPACITORS • Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.) 䚷Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance 䚷slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on 䚷a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant 䚷circuit. 䚷Please contact us if you need a detail information. 䚷䚷䚷NOTE 1. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2. You are requested not to use our product deviating from this specification. EGLEDMNO03 2/18 Reference only 1. Application This specification is applied to Leaded MLCC RCE series in accordance with AEC-Q200 requirements used for Automotive Electronic equipment. 2. Rating • Part Number Configuration ex.) RCE Series 2E 102 K 1 Temperature R7 Rated Capacitance Capacitance Dimension Characteristics Voltage Tolerance (LxW) K1 H03 Lead Individual B Style Specification Package • Temperature Characteristics Code Temp. Char. Temp. Range Cap. Change Standard Temp. Operating Temp. Range R7 X7R (EIA code) -55到125°C +/-15% 25°C -55到125°C • Rated Voltage Code 2E 2J 3A Rated voltage DC250V DC630V DC1000V • Capacitance The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF. ex.) In case of 102 2 10×10 = 1000pF • Capacitance Tolerance Code Capacitance Tolerance K +/-10% • Dimension (LxW) Please refer to [ Part number list ]. • Lead Style *Lead wire is "solder coated CP wire". Code Lead Style B1 Straight type E1 Straight taping type K1 Inside crimp type M1 Inside crimp taping type Lead spacing (mm) 5.0+/-0.8 5.0+0.6/-0.2 5.0+/-0.8 5.0+0.6/-0.2 • Individual Specification Murata’s control code. Please refer to [ Part number list ]. • Package Code A B Package Taping type of Ammo Bulk type 7(,.$.8 3/18 Reference only 3. Marking Temp. char. Capacitance Capacitance tolerance Rated voltage Company name code : : : : Letter code : C (X7R char. Except dimension code : 1) 3 digit numbers Code Letter code : 4 (DC250V. Except dimension code : 1) Letter code : 7 (DC630V) Letter code : A (DC1000V) : Abbreviation : (Except dimension code : 1) (Ex.) Rated voltage DC250V DC630V DC1000V Dimension code 1 2 103K 㸫 473 K4C 153 K7C 㸫 102 KAC 3,4 224 K4C 104 K7C 333 KAC 5 474 K4C 224 M7C 104 KAC 7(,.$.8 4/18 Reference only 4. Part number list Unit : mm Customer Part Number Murata Part Number T.C. DC Rated Volt. (V) Cap. Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack (LxW) qty. Lead Style (pcs) RCER72E102K1K1H03B X7R 250 1000pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E152K1K1H03B X7R 250 1500pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E222K1K1H03B X7R 250 2200pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E332K1K1H03B X7R 250 3300pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E472K1K1H03B X7R 250 4700pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E682K1K1H03B X7R 250 6800pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E103K1K1H03B X7R 250 10000pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E153K1K1H03B X7R 250 15000pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E223K1K1H03B X7R 250 22000pF ±10% 4.0 3.5 5.0 5.0 3.15 1K1 500 RCER72E333K2K1H03B X7R 250 33000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72E473K2K1H03B X7R 250 47000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72E683K2K1H03B X7R 250 68000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72E104K2K1H03B X7R 250 0.10μF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72E154K3K1H03B X7R 250 0.15μF ±10% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCER72E224K3K1H03B X7R 250 0.22μF ±10% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCER72E334K4K1H03B X7R 250 0.33μF ±10% 7.5 5.5 8.0 5.0 4.0 4K1 500 500 RCER72E474K4K1H03B X7R 250 0.47μF ±10% 7.5 5.5 8.0 5.0 4.0 4K1 RCER72E684K5B1H03B X7R 250 0.68μF ±10% 7.5 7.5 - 5.0 4.0 5B1 500 RCER72E105K5B1H03B X7R 250 1.0μF ±10% 7.5 7.5 - 5.0 4.0 5B1 500 PNLIST 5/18 Reference only Unit : mm Customer Part Number Murata Part Number T.C. DC Rated Volt. (V) Cap. Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack (LxW) qty. Lead Style (pcs) RCER72J102K2K1H03B X7R 630 1000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J152K2K1H03B X7R 630 1500pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J222K2K1H03B X7R 630 2200pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J332K2K1H03B X7R 630 3300pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J472K2K1H03B X7R 630 4700pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J682K2K1H03B X7R 630 6800pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J103K2K1H03B X7R 630 10000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J153K2K1H03B X7R 630 15000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J223K2K1H03B X7R 630 22000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER72J333K3K1H03B X7R 630 33000pF ±10% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCER72J473K3K1H03B X7R 630 47000pF ±10% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCER72J683K4K1H03B X7R 630 68000pF ±10% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCER72J104K4K1H03B X7R 630 0.10μF ±10% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCER72J154K5B1H03B X7R 630 0.15μF ±10% 7.5 8.0 - 5.0 4.0 5B1 500 RCER72J224K5B1H03B X7R 630 0.22μF ±10% 7.5 8.0 - 5.0 4.0 5B1 500 PNLIST 6/18 Reference only Unit : mm Customer Part Number Murata Part Number T.C. DC Rated Volt. (V) Cap. Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack (LxW) qty. Lead Style (pcs) RCER73A102K2K1H03B X7R 1000 1000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A152K2K1H03B X7R 1000 1500pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A222K2K1H03B X7R 1000 2200pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A332K2K1H03B X7R 1000 3300pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A472K2K1H03B X7R 1000 4700pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A682K2K1H03B X7R 1000 6800pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A103K2K1H03B X7R 1000 10000pF ±10% 5.5 4.0 6.0 5.0 3.15 2K1 500 RCER73A153K3K1H03B X7R 1000 15000pF ±10% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCER73A223K3K1H03B X7R 1000 22000pF ±10% 5.5 5.0 7.5 5.0 4.0 3K1 500 RCER73A333K4K1H03B X7R 1000 33000pF ±10% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCER73A473K4K1H03B X7R 1000 47000pF ±10% 7.5 5.5 8.0 5.0 4.0 4K1 500 RCER73A683K5B1H03B X7R 1000 68000pF ±10% 7.5 8.0 - 5.0 4.0 5B1 500 RCER73A104K5B1H03B X7R 1000 0.10μF ±10% 7.5 8.0 - 5.0 4.0 5B1 500 PNLIST 7/18 Reference only Unit : mm Customer Part Number DC Rated T.C. Volt. (V) Cap. RCER72E102K1M1H03A X7R 250 1000pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E152K1M1H03A X7R 250 1500pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E222K1M1H03A X7R 250 2200pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E332K1M1H03A X7R 250 3300pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E472K1M1H03A X7R 250 4700pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E682K1M1H03A X7R 250 6800pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E103K1M1H03A X7R 250 10000pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E153K1M1H03A X7R 250 15000pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E223K1M1H03A X7R 250 22000pF ±10% 4.0 3.5 5.0 5.0 3.15 16.0 1M1 2000 RCER72E333K2M1H03A X7R 250 33000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72E473K2M1H03A X7R 250 47000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72E683K2M1H03A X7R 250 68000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72E104K2M1H03A X7R 250 0.10μF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72E154K3M1H03A X7R 250 0.15μF ±10% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCER72E224K3M1H03A X7R 250 0.22μF ±10% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCER72E334K4M1H03A X7R 250 0.33μF ±10% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCER72E474K4M1H03A X7R 250 0.47μF ±10% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCER72E684K5E1H03A X7R 250 0.68μF ±10% 7.5 7.5 - 5.0 4.0 17.5 5E1 1500 RCER72E105K5E1H03A X7R 250 1.0μF ±10% 7.5 7.5 - 5.0 4.0 17.5 5E1 1500 Murata Part Number PNLIST 8/18 Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack (LxW) qty. H/H0 Lead Style (pcs) Reference only Unit : mm Customer Part Number DC Rated T.C. Volt. (V) Cap. RCER72J102K2M1H03A X7R 630 1000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J152K2M1H03A X7R 630 1500pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J222K2M1H03A X7R 630 2200pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J332K2M1H03A X7R 630 3300pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J472K2M1H03A X7R 630 4700pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J682K2M1H03A X7R 630 6800pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J103K2M1H03A X7R 630 10000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J153K2M1H03A X7R 630 15000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J223K2M1H03A X7R 630 22000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER72J333K3M1H03A X7R 630 33000pF ±10% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCER72J473K3M1H03A X7R 630 47000pF ±10% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCER72J683K4M1H03A X7R 630 68000pF ±10% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCER72J104K4M1H03A X7R 630 0.10μF ±10% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCER72J154K5E1H03A X7R 630 0.15μF ±10% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 RCER72J224K5E1H03A X7R 630 0.22μF ±10% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 Murata Part Number PNLIST 9/18 Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack (LxW) qty. H/H0 Lead Style (pcs) Reference only Unit : mm Customer Part Number DC Rated T.C. Volt. (V) Cap. RCER73A102K2M1H03A X7R 1000 1000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A152K2M1H03A X7R 1000 1500pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A222K2M1H03A X7R 1000 2200pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A332K2M1H03A X7R 1000 3300pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A472K2M1H03A X7R 1000 4700pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A682K2M1H03A X7R 1000 6800pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A103K2M1H03A X7R 1000 10000pF ±10% 5.5 4.0 6.0 5.0 3.15 16.0 2M1 2000 RCER73A153K3M1H03A X7R 1000 15000pF ±10% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCER73A223K3M1H03A X7R 1000 22000pF ±10% 5.5 5.0 7.5 5.0 4.0 16.0 3M1 2000 RCER73A333K4M1H03A X7R 1000 33000pF ±10% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCER73A473K4M1H03A X7R 1000 47000pF ±10% 7.5 5.5 8.0 5.0 4.0 16.0 4M1 1500 RCER73A683K5E1H03A X7R 1000 68000pF ±10% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 RCER73A104K5E1H03A X7R 1000 0.10μF ±10% 7.5 8.0 - 5.0 4.0 17.5 5E1 1500 Murata Part Number PNLIST 10/18 Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack (LxW) qty. H/H0 Lead Style (pcs) Reference only 5. AEC-Q200 Murata Standard Specifications and Test Methods AEC-Q200 No. 1 Specification Test Item AEC-Q200 Test Method Pre-and Post-Stress - Electrical Test 2 3 High Appearance No defects or abnormalities. Sit the capacitor for 1000±12h at 150±3°C. Let sit for 24±2h at, Temperature Capacitance within ±12.5% *room condition then measure. Exposure Change (Storage) D.F. 0.04 max. •Pretreatment I.R. More than 1,000MΩ or 50MΩ䞉μF Perform the heat treatment at 150+0/-10°C for 60±5 min and (Whichever is smaller) then let sit for 24±2 h at *room condition. Temperature Appearance No defects or abnormalities. Perform the 1000 cycles according to the four heat treatments Cycling Capacitance within ±12.5% listed in the following table. Let sit for 24±2 h at *room condition, Change then measure. D.F. 0.05 max. I.R. 1,000MΩ or 50MΩ䞉μF min. (Whichever is smaller) •Pretreatment Perform the heat treatment at 150+0/-10°C for 60±5 min and then let sit for 24±2 h at *room condition. 4 Moisture Appearance No defects or abnormalities Apply the 24h heat (25 to 65°C) and humidity (80 to 98%) Resistance Capacitance within ±12.5% treatment shown below, 10 consecutive times. Change Let sit for 24±2 h at *room condition, then measure. D.F. 0.05 max. I.R. 500MΩ or 25MΩ·μF min. (Whichever is smaller) •Pretreatment Perform the heat treatment at 150+0/-10°C for 60±5 min and then let sit for 24±2 h at *room condition. 5 Biased Appearance No defects or abnormalities Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor) Humidity Capacitance within ±12.5% at 85±3°C and 80 to 85% humidity for 1000±12h. Change Remove and let sit for 24±2 h at *room condition, then measure. D.F. 0.05 max. I.R. 500MΩ or 25MΩ·μF min. (Whichever is smaller) The charge/discharge current is less than 50mA. •Pretreatment Perform the heat treatment at 150+0/-10°C for 60±5 min and then let sit for 24±2 h at *room condition. 6 Operational Appearance No defects or abnormalities Apply voltage in Table for 1000±12h at 125±3°C. Life Capacitance within ±12.5% Let sit for 24±2 h at *room condition, then measure. Change The charge/discharge current is less than 50mA. D.F. 0.04 max. •Pretreatment I.R. 1,000MΩ or 50MΩ·μF min. Apply test voltage for 60±5 min at test temperature. (Whichever is smaller) Remove and let sit for 24±2 h at *room condition. 7 External Visual No defects or abnormalities. Visual inspection. 8 Physical Dimension Within the specified dimensions. Using calipers and micrometers. 9 Marking To be easily legible. Visual inspection. * “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa ESRCE03C 11/18 Reference only AEC-Q200 No. 10 Specification Test Item AEC-Q200 Test Method Resistance Appearance No defects or abnormalities. to Solvents Capacitance Within the specified tolerance. Per MIL-STD-202 Method 215 D.F. 0.025 max. I.R. More than 10,000MΩ or 500 MΩ䞉μF Solvent 2 : Terpene defluxer (Whichever is smaller) Solvent 3 : 42 parts (by volume) of water Solvent 1 : 1 part (by volume) of isopropyl alcohol 3 parts (by volume) of mineral spirits 1 part (by volume) of propylene glycol monomethyl ether 1 part (by volume) of monoethanolamine 11 Mechanical Appearance No defects or abnormalities. Three shocks in each direction should be applied along 3 Shock Capacitance Within the specified tolerance. mutually perpendicular axes of the test specimen (18 shocks). D.F. 0.025 max. The specified test pulse should be Half-sine and should have a duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s. 12 Vibration Appearance No defects or abnormalities. The capacitor should be subjected to a simple harmonic motion Capacitance Within the specified tolerance. having a total amplitude of 1.5mm, the frequency being varied D.F. 0.025 max. uniformly between the approximate limits of 10 and 2,000Hz. The frequency range, from 10 to 2000Hz and return to 10Hz, should be traversed in approximately 20 min. This motion should be applied for 12 items in each 3 mutually perpendicular directions (total of 36 times). 13-1 Resistance Appearance No defects or abnormalities. The lead wires should be immersed in the melted solder 1.5 to to Soldering Capacitance Within ±7.5% 2.0mm from the root of terminal at 260±5°C for 10±1 seconds. Heat Change (Non- Dielectric Preheat) Strength No defects • Pre-treatment Capacitor should be stored at 150+0/-10°C for one (Between hour, then place at *room condition for 24±2 hours before initial terminals) measurement. • Post-treatment Capacitor should be stored for 24±2 hours at *room condition. 13-2 Resistance Appearance No defects or abnormalities. First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds. to Soldering Capacitance Within ±7.5% Then, the lead wires should be immersed in the melted solder 1.5 to Heat Change (On- Dielectric Preheat) Strength 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds. No defects • Pre-treatment (Between Capacitor should be stored at 150+0/-10°C for one hour, then place at terminals) *room condition for 24±2 hours before initial measurement. • Post-treatment Capacitor should be stored for 24±2 hours at *room condition. 13-3 Resistance Appearance No defects or abnormalities. to Soldering Capacitance Within ±7.5% Heat Change (soldering iron method) Dielectric Test condition Termperature of iron-tip : 350±10°C Soldering time No defects : 3.5±0.5 seconds Soldering position Strength Straight Lead : 1.5 to 2.0mm from the root of terminal. (Between Crimp Lead : 1.5 to 2.0mm from the end of lead bend. terminals) • Pre-treatment Capacitor should be stored at 150+0/-10°C for one hour, then place at *room condition for 24±2 hours before initial measurement. • Post-treatment 14 Thermal Appearance No defects or abnormalities. Capacitor should be stored for 24±2 hours at *room condition. Perform the 300 cycles according to the two heat treatments listed in Shock Capacitance within ±12.5% the following table (Maximum transfer time is 20s.). Let sit for 24±2 h at Change *room condition, then measure. D.F. 0.05 max. I.R. 1,000MΩ or 50MΩ䞉μF min. (Whichever is smaller) •Pretreatment Perform the heat treatment at 150+0/-10°C for 60±5 min and then let sit for 24±2 h at *room condition. 15 ESD Appearance No defects or abnormalities Capacitance Within the specified tolerance D.F. 0.025 max. I.R. More than 10,000MΩ or 100 MΩ䞉μF Per AEC-Q200-002 (Whichever is smaller) * “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa ESRCE03C 12/18 Reference only AEC-Q200 No. 16 Specifications Test Item Solderability AEC-Q200 Test Method Lead wire should be soldered with uniform Should be placed into steam aging for 8h±15 min. coating on the axial direction over 95% of The terminal of capacitor is dipped into a solution of ethanol the circumferential direction. (JIS K 8101) and rosin (JIS K 5902) (25% rosin in weight propotion).Immerse in solder solution for 2±0.5 seconds. In both cases the depth of dipping is up to about 1.5 to 2mm from the terminal body. Temp. of solder : 245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu) 235±5°C H60A or H63A Eutectic Solder 17 Apperance No defects or abnormalities. Visual inspection. Characte- Capacitance Within the specified tolerance. The capacitance/D.F. should be measured at 25°C at the frequency rization D.F. 0.025 max. and voltage shown in the table. Electrical I.R. Between 10,000MΩ or 100MΩ䞉μF min. The insulation resistance should be measured with DC500V Terminals (Whichever is smaller) (DC250V in case of rated voltage : DC250V) at 25 °C within 2 min. Dielectric Between The capacitor should not be damaged when voltage inTable is Strength Terminals of charging. No defects or abnormalities applied between the terminations for 1 to 5 seconds. (Charge/Discharge current 䍺 50mA.) Body No defects or abnormalities Insulation The capacitor is placed in a container with metal balls of 1mm diameter so that each terminal, short-circuit is kept approximately 2mm from the balls, and 200% of the rated DC voltage(DC1300V in case of rated voltage : DC630V,DC1000V) is impressed for 1 to 5 seconds between capacitor terminals and metal balls. (Charge/Discharge current ӌ 50mA.) 18 Terminal Tensile Strength Strength Termination not to be broken or loosened. As in the figure, fix the capacitor body, apply the force gradually to each lead in the radial direction of the capacitor until reaching 10N and then keep the force applied for 10±1 seconds. F Bending Termination not to be broken or loosened. Strength Each lead wire should be subjected to a force of 2.5N and then be bent 90° at the point of egress in one direction. Each wire is then returned to the original position and bent 90° in the opposite direction at the rate of one bend per 2 to 3 seconds. 19 Capacitance Within ±15% The capacitance change should be measured after 5min. at Temperature each specified temperature step. Characteristics The ranges of capacitance change compared with the above 25°C value over the temperature ranges shown in the table should be within the specified ranges. •Pretreatment Perform the heat treatment at 150+0/-10°C for 60±5 min and then let sit for 24±2 h at *room condition. Perform the initial measurement. * “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa ESRCE03C 13/18 Reference only 6. Packing specification 䞉Bulk type (Packing style code : B) The size of packing case and packing way Polyethylene bag Partition 270 max. 125 max. Unit : mm 340 max. The number of packing = *1 Packing quantity 㽢 *2 n *1 : Please refer to [Part number list]. *2 : Standard n = 20 (bag) Note) The outer package and the number of outer packing be changed by the order getting amount. JKBCRPE02 14/18 Reference only 䞉Ammo pack taping type (Packing style code : A) 䚷䚷䚷䚷䚷䚷A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case. 䚷䚷䚷䚷䚷䚷When body of the capacitor is piled on other body under it. The size of packing case and packing way 240 max. Position of label 340 max. Unit : mm 51 max. Hold down tape Capacitor Base tape Hold down tape upper EKTRPE01 15/18 Reference only 7. Taping specification 7-1. Dimension of capacitors on tape Straight taping type < Lead Style : E1 > Pitch of component 12.7mm / Lead spacing 5.0mm P2 0 P ‫ڹ‬h2 ‫ڹ‬h1 ‫ڹ‬S Marking t2 t1 W W0 L ID0 W2 Id W1 F H e P1 P0 Unit : mm Item Code Dimensions Pitch of component P 12.7+/-1.0 Pitch of sprocket hole P0 12.7+/-0.2 Lead spacing F 5.0+0.6/-0.2 Length from hole center to component center P2 6.35+/-1.3 Length from hole center to lead P1 3.85+/-0.7 Deviation along tape, left or right defect 'S 0+/-2.0 Carrier tape width W 18.0+/-0.5 Position of sprocket hole W1 9.0+0/-0.5 H 17.5+/-0.5 For straight lead type Protrusion length Diameter of sprocket hole 4.0+/-0.1 Lead diameter Φd 0.5+/-0.05 Total tape thickness t1 0.6+/-0.3 Total thickness of tape and lead wire t2 1.5 max. Portion to cut in case of defect They include deviation by lead bend Deviation of tape width direction They include hold down tape thickness. 'h1 2.0 max.㸦Dimension code㸸U㸧 'h2 1.0 max.㸦except as above㸧 L 11.0+0/-1.0 Hold down tape width W0 9.5 min. Hold down tape position W2 1.5+/-1.5 Coating extension on lead Deviation of progress direction 0.5 max. ΦD0 Deviation across tape Remarks e 2.0 max.㸦Dimension code㸸U㸧 1.5 max.㸦except as above㸧 ETP1E101B 16/18 Reference only Inside crimp taping type < Lead Style : M1 > Pitch of component 12.7mm / Lead spacing 5.0mm P2 P Δh1 0 Δh2 ΔS Marking t1 t2 W0 L ΦD0 W Φd W1 H0 F W2 e P1 P0 Unit : mm Item Code Dimensions Pitch of component P 12.7+/-1.0 Pitch of sprocket hole P0 12.7+/-0.2 Lead spacing F 5.0+0.6/-0.2 Length from hole center to component center P2 6.35+/-1.3 Length from hole center to lead P1 3.85+/-0.7 Deviation along tape, left or right defect ΔS 0+/-2.0 Carrier tape width W 18.0+/-0.5 Position of sprocket hole W1 9.0+0/-0.5 Lead distance between reference and bottom plane H0 16.0+/-0.5 Protrusion length Diameter of sprocket hole ΦD0 4.0+/-0.1 Φd 0.5+/-0.05 Total tape thickness t1 0.6+/-0.3 Total thickness of tape and lead wire t2 1.5 max. Portion to cut in case of defect They include deviation by lead bend Deviation of tape width direction They include hold down tape thickness 䂴h1 䚷䚷䚷2.0 max. (Dimension code : W) 䂴h2 䚷䚷䚷1.0 max. (except as above) L 11.0+0/-1.0 Hold down tape width W0 9.5 min. Hold down tape position W2 Coating extension on lead Deviation of progress direction 0.5 max. Lead diameter Deviation across tape Remarks e 1.5+/-1.5 Up to the end of crimp ETP1M101A 17/18 Reference only ࠉࠉ7-2. Splicing way of tape 1) Adhesive force of tape is over 3N at test condition as below. W Hold down tape Base tape 2) Splicing of tape ࠉࠉࠉa) When base tape is spliced •Base tape shall be spliced by cellophane tape. (Total tape thickness shall be less than 1.05mm.) Progress direction in production line Hold down tape Base tape No lifting for the direction of progressing About 30 to 50 Cellophane tape Unit : mm ࠉࠉࠉb) When hold down tape is spliced ࠉࠉࠉ •Hold down tape shall be spliced with overlapping. (Total tape thickness shall be less than 1.05mm.) 20 to 30 Progress direction in production line Hold down tape Base tape Unit : mm ࠉࠉࠉc) When both tape are spliced •Base tape and hold down tape shall be spliced with splicing tape. ETP2R01 18/18