Reference Specification
Leaded MLCC for General Purpose
RDE Series
Product specifications in this catalog are as of Dec. 2017, and are subject to change or
obsolescence without notice.
Please consult the approval sheet before ordering.Please read rating and Cautions first.
Reference only
CAUTION
1. OPERATING VOLTAGE
When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p
value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When
the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be
generated for a transit period because of resonance or switching. Be sure to use a capacitor within
rated voltage containing these irregular voltage.
When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),
be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or
impulse withstand established for each equipment should be taken into considerations.
Voltage
DC Voltage
Positional
Measurement Vo-p
DC+AC Voltage
Vo-p
AC Voltage
Vp-p
Pulse Voltage(1)
Vp-p
Pulse Voltage(2)
Vp-p
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature
range. Be sure to take into account the heat generated by the capacitor itself.
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),
applied voltage should be the load such as self-generated heat is within 20 C on the condition of
atmosphere temperature 25 C. Please contact us if self-generated heat is occurred with Class 1
capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal
capacity-K of 0.1mm and be in the condition where capacitor is not affected by radiant heat of other
components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s
characteristics and reliability.
3. Fail-safe
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that
may be caused by the abnormal function or the failure of our product.
4. OPERATING AND STORAGE ENVIRONMENT
The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the
like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product,
verify that these processes do not affect product quality by testing the performance of a cleaned, bonded
or molded product in the intended equipment. Store the capacitors where the temperature and relative
humidity do not exceed 5 to 40 C and 20 to 70%. Use capacitors within 6 months.
5. VIBRATION AND IMPACT
Do not expose a capacitor or its leads to excessive shock or vibration during use.
6. SOLDERING
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of
the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and
may result in thermal shocks that can crack the ceramic element.
7. BONDING AND RESIN MOLDING, RESIN COAT
In case of bonding, molding or coating this product, verify that these processes do not affect the quality
of capacitor by testing the performance of a bonded or molded product in the intended equipment.
In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins
containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer
coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short
circuit.
The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or
ceramic element cracking of a capacitor in a temperature cycling.
8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT
When the outer coating is hot (over 100 C) after soldering, it becomes soft and fragile.
So please be careful not to give it mechanical stress.
EGLEDMNO03
1 / 19
Reference only
Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial
dispersion when the product is used.
9. LIMITATION OF APPLICATIONS
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party’s life,
body or property.
1. Aircraft equipment
2. Aerospace equipment
3. Undersea equipment
4. Power plant control equipment
5. Medical equipment
6. Transportation equipment (vehicles, trains, ships, etc.)
7. Traffic signal equipment
8. Disaster prevention / crime prevention equipment
9. Data-processing equipment exerting influence on public
10. Application of similar complexity and/or reliability requirements to the applications listed in the above.
NOTICE
1. CLEANING (ULTRASONIC CLEANING)
To perform ultrasonic cleaning, observe the following conditions.
Rinse bath capacity : Output of 20 watts per liter or less.
Rinsing time : 5 min maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.
2. Soldering and Mounting
Insertion of the Lead Wire
• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.
• Insert the lead wire into the PCB with a distance appropriate to the lead space.
3. CAPACITANCE CHANGE OF CAPACITORS
• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.)
Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance
slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on
a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant
circuit.
Please contact us if you need a detail information.
NOTE
1. Please make sure that your product has been evaluated in view of your specifications with our product
being mounted to your product.
2. You are requested not to use our product deviating from this specification.
EGLEDMNO03
2 / 19
Reference only
1. Application
This product specification is applied to Leaded MLCC RDE series used for General Electronic equipment.
Do not use these products in any automotive power train or safety equipment including battery chargers
for electric vehicles and plug-in hybrids.
2. Rating
Part number configuration
ex.) RDE
R7
1H
Series
Temperature
Characteristic
Rated
voltage
103
K
0
K1
H03
B
Capacitance
Capacitance
tolerance
Dimension
code
Lead
code
Individual
specification
code
Packing
style
code
Temperature characteristic
Temp.
Temp. Range
Code
Char.
R7
X7R
C7
X7S
Rated voltage
Code
1E
1H
2A
Cap. Change
(Within%)
Standard
Temp.
Operating
Temp. Range
25C
-55～125C
+/-15
-55～125C
+/-22
Rated voltage
DC25V
DC50V
DC100V
Capacitance
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.
ex.) In case of 103.
10103 = 10000pF
Capacitance tolerance
Code
Capacitance Tolerance
K
+/-10%
M
+/-20%
Dimension code
Code
0
1
2
3
W
Lead code
Code
K1
M1
P1
S1
Dimensions (LxW) mm max.
4.0 x 3.5 ( Lead code : K1, M1 )
5.0 x 3.5 ( Lead code : P1, S1 )
4.5 x 3.5 ( Lead code : K1, M1 )
5.0 x 3.5 ( Lead code : P1, S1 )
5.5 x 4.0
5.5 x 5.0
5.5 x 7.5
Lead style
Inside crimp type
Inside crimp taping type
Outside crimp type
Outside crimp taping type
Lead spacing (mm)
5.0+/-0.8
5.0+0.6/-0.2
2.5+/-0.8
2.5+0.4/-0.2
Lead wire is solder coated CP wire.
ETRDE118B
3 / 19
Reference only
Individual specification code
Murata’s control code
Please refer to Part number list .
Packing style code
Code
Packing style
A
Taping type of Ammo
B
Bulk type
3. Marking
Temp. char.
Capacitance
Capacitance tolerance
Rated voltage
: Letter code : C (X7R/X7S Char. Except dimension code : 0,1)
: 3 digit numbers
: Code
: Letter code : 2 (DC25V only. Except dimension code : 0,1)
Letter code : 5 (DC50V only. Except dimension code : 0,1)
Letter code : 1 (DC100V only. Except dimension code : 0,1)
Company name code : Abbreviation :
(Except dimension code : 0,1)
(Ex.)
Rated voltage
25V
50V
100V
104K
103K
224K
Dimension code
0,1
2
3,W
475
K2C
226
K2C
ETRDE118B
4 / 19
105
K5C
105
K1C
335
K5C
225
K1C
Reference only
4. Part number list
Unit : mm
Customer Part Number
DC
Rated
T.C.
Volt.
(V)
Cap.
RDER71E104K0P1H03B
X7R
25
0.10µF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDEC71E224K0P1H03B
X7S
25
0.22µF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDEC71E474K0P1H03B
X7S
25
0.47µF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDEC71E105K0P1H03B
X7S
25
1.0µF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDEC71E225K1P1H03B
X7S
25
2.2µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDEC71E475K2P1H03B
X7S
25
4.7µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDEC71E106K2P1H03B
X7S
25
10µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDEC71E226K3P1H03B
X7S
25
22µF ±10%
5.5
5.0
7.5
2.5
4.0 3P1
500
RDER71H221K0P1H03B
X7R
50
220pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H331K0P1H03B
X7R
50
330pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H471K0P1H03B
X7R
50
470pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H681K0P1H03B
X7R
50
680pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H102K0P1H03B
X7R
50
1000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H152K0P1H03B
X7R
50
1500pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H222K0P1H03B
X7R
50
2200pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H332K0P1H03B
X7R
50
3300pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H472K0P1H03B
X7R
50
4700pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H682K0P1H03B
X7R
50
6800pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H103K0P1H03B
X7R
50
10000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H153K0P1H03B
X7R
50
15000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H223K0P1H03B
X7R
50
22000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H333K0P1H03B
X7R
50
33000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H473K0P1H03B
X7R
50
47000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H683K0P1H03B
X7R
50
68000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H104K0P1H03B
X7R
50
0.10µF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER71H154K1P1H03B
X7R
50
0.15µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER71H224K1P1H03B
X7R
50
0.22µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER71H334K1P1H03B
X7R
50
0.33µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER71H474K1P1H03B
X7R
50
0.47µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER71H684K2P1H03B
X7R
50
0.68µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDEC71H105K1P1H03B
X7S
50
1.0µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER71H105K2P1H03B
X7R
50
1.0µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDER71H155K2P1H03B
X7R
50
1.5µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDER71H225K2P1H03B
X7R
50
2.2µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDER71H335K3P1H03B
X7R
50
3.3µF ±10%
5.5
5.0
7.5
2.5
4.0 3P1
500
RDEC71H475K2P1H03B
X7S
50
4.7µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDEC71H106K3P1H03B
X7S
50
10µF ±10%
5.5
5.0
7.5
2.5
4.0 3P1
500
RDER72A221K0P1H03B
X7R
100
220pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A331K0P1H03B
X7R
100
330pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A471K0P1H03B
X7R
100
470pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
Murata Part Number
5 / 19
Cap.
tol.
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
Code (pcs)
Reference only
Unit : mm
Customer Part Number
Murata Part Number
DC
Rated
T.C.
Volt.
(V)
Cap.
Cap.
tol.
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
Code (pcs)
RDER72A681K0P1H03B
X7R
100
680pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A102K0P1H03B
X7R
100
1000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A152K0P1H03B
X7R
100
1500pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A222K0P1H03B
X7R
100
2200pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A332K0P1H03B
X7R
100
3300pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A472K0P1H03B
X7R
100
4700pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A682K0P1H03B
X7R
100
6800pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A103K0P1H03B
X7R
100
10000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A153K0P1H03B
X7R
100
15000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A223K0P1H03B
X7R
100
22000pF ±10%
5.0
3.5
6.0
2.5
2.5 0P1
500
RDER72A333K1P1H03B
X7R
100
33000pF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A473K1P1H03B
X7R
100
47000pF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A683K1P1H03B
X7R
100
68000pF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A104K1P1H03B
X7R
100
0.10µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A154K2P1H03B
X7R
100
0.15µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDER72A224K1P1H03B
X7R
100
0.22µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A334K1P1H03B
X7R
100
0.33µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A474K1P1H03B
X7R
100
0.47µF ±10%
5.0
3.5
5.0
2.5
3.15 1P1
500
RDER72A684K2P1H03B
X7R
100
0.68µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDER72A105K2P1H03B
X7R
100
1.0µF ±10%
5.5
4.0
6.0
2.5
3.15 2P1
500
RDEC72A155K3P1H03B
X7S
100
1.5µF ±10%
5.5
5.0
7.5
2.5
4.0 3P1
500
RDEC72A225K3P1H03B
X7S
100
2.2µF ±10%
5.5
5.0
7.5
2.5
4.0 3P1
500
RDER71E104K0K1H03B
X7R
25
0.10µF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDEC71E224K0K1H03B
X7S
25
0.22µF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDEC71E474K0K1H03B
X7S
25
0.47µF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDEC71E105K0K1H03B
X7S
25
1.0µF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDEC71E225K1K1H03B
X7S
25
2.2µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDEC71E475K2K1H03B
X7S
25
4.7µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDEC71E106K2K1H03B
X7S
25
10µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDEC71E226K3K1H03B
X7S
25
22µF ±10%
5.5
5.0
7.5
5.0
4.0 3K1
500
RDEC71E476MWK1H03B
X7S
25
47µF ±20%
5.5
7.5
10.0
5.0
4.0 WK1
500
RDER71H221K0K1H03B
X7R
50
220pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H331K0K1H03B
X7R
50
330pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H471K0K1H03B
X7R
50
470pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H681K0K1H03B
X7R
50
680pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H102K0K1H03B
X7R
50
1000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H152K0K1H03B
X7R
50
1500pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H222K0K1H03B
X7R
50
2200pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H332K0K1H03B
X7R
50
3300pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H472K0K1H03B
X7R
50
4700pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
6 / 19
Reference only
Unit : mm
Customer Part Number
Murata Part Number
DC
Rated
T.C.
Volt.
(V)
Cap.
Cap.
tol.
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
Code (pcs)
RDER71H682K0K1H03B
X7R
50
6800pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H103K0K1H03B
X7R
50
10000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H153K0K1H03B
X7R
50
15000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H223K0K1H03B
X7R
50
22000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H333K0K1H03B
X7R
50
33000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H473K0K1H03B
X7R
50
47000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H683K0K1H03B
X7R
50
68000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H104K0K1H03B
X7R
50
0.10µF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER71H154K1K1H03B
X7R
50
0.15µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER71H224K1K1H03B
X7R
50
0.22µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER71H334K1K1H03B
X7R
50
0.33µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER71H474K1K1H03B
X7R
50
0.47µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER71H684K2K1H03B
X7R
50
0.68µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDEC71H105K1K1H03B
X7S
50
1.0µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER71H105K2K1H03B
X7R
50
1.0µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDER71H155K2K1H03B
X7R
50
1.5µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDER71H225K2K1H03B
X7R
50
2.2µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDER71H335K3K1H03B
X7R
50
3.3µF ±10%
5.5
5.0
7.5
5.0
4.0 3K1
500
RDEC71H475K2K1H03B
X7S
50
4.7µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDEC71H106K3K1H03B
X7S
50
10µF ±10%
5.5
5.0
7.5
5.0
4.0 3K1
500
RDEC71H226MWK1H03B
X7S
50
22µF ±20%
5.5
7.5
10.0
5.0
4.0 WK1
500
RDER72A221K0K1H03B
X7R
100
220pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A331K0K1H03B
X7R
100
330pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A471K0K1H03B
X7R
100
470pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A681K0K1H03B
X7R
100
680pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A102K0K1H03B
X7R
100
1000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A152K0K1H03B
X7R
100
1500pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A222K0K1H03B
X7R
100
2200pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A332K0K1H03B
X7R
100
3300pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A472K0K1H03B
X7R
100
4700pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A682K0K1H03B
X7R
100
6800pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A103K0K1H03B
X7R
100
10000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A153K0K1H03B
X7R
100
15000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A223K0K1H03B
X7R
100
22000pF ±10%
4.0
3.5
6.0
5.0
2.5 0K1
500
RDER72A333K1K1H03B
X7R
100
33000pF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A473K1K1H03B
X7R
100
47000pF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A683K1K1H03B
X7R
100
68000pF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A104K1K1H03B
X7R
100
0.10µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A154K2K1H03B
X7R
100
0.15µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
7 / 19
Reference only
Unit : mm
Customer Part Number
DC
Rated
T.C.
Volt.
(V)
Cap.
RDER72A224K1K1H03B
X7R
100
0.22µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A334K1K1H03B
X7R
100
0.33µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A474K1K1H03B
X7R
100
0.47µF ±10%
4.5
3.5
5.0
5.0
3.15 1K1
500
RDER72A684K2K1H03B
X7R
100
0.68µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDER72A105K2K1H03B
X7R
100
1.0µF ±10%
5.5
4.0
6.0
5.0
3.15 2K1
500
RDEC72A155K3K1H03B
X7S
100
1.5µF ±10%
5.5
5.0
7.5
5.0
4.0 3K1
500
RDEC72A225K3K1H03B
X7S
100
2.2µF ±10%
5.5
5.0
7.5
5.0
4.0 3K1
500
RDEC72A475MWK1H03B
X7S
100
4.7µF ±20%
5.5
7.5
10.0
5.0
4.0 WK1
500
Murata Part Number
8 / 19
Cap.
tol.
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
Code (pcs)
Reference only
Unit : mm
Customer Part Number
Murata Part Number
DC
Rated
T.C.
Cap. Cap. tol.
volt.
(V)
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
H0 Code (pcs)
RDER71E104K0S1H03A
X7R
25
0.10µF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDEC71E224K0S1H03A
X7S
25
0.22µF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDEC71E474K0S1H03A
X7S
25
0.47µF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDEC71E105K0S1H03A
X7S
25
1.0µF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDEC71E225K1S1H03A
X7S
25
2.2µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDEC71E475K2S1H03A
X7S
25
4.7µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDEC71E106K2S1H03A
X7S
25
10µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDEC71E226K3S1H03A
X7S
25
22µF ±10%
5.5
5.0
7.5
2.5
4.0
16.0 3S1
1500
RDER71H221K0S1H03A
X7R
50
220pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H331K0S1H03A
X7R
50
330pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H471K0S1H03A
X7R
50
470pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H681K0S1H03A
X7R
50
680pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H102K0S1H03A
X7R
50
1000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H152K0S1H03A
X7R
50
1500pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H222K0S1H03A
X7R
50
2200pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H332K0S1H03A
X7R
50
3300pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H472K0S1H03A
X7R
50
4700pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H682K0S1H03A
X7R
50
6800pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H103K0S1H03A
X7R
50
10000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H153K0S1H03A
X7R
50
15000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H223K0S1H03A
X7R
50
22000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H333K0S1H03A
X7R
50
33000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H473K0S1H03A
X7R
50
47000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H683K0S1H03A
X7R
50
68000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H104K0S1H03A
X7R
50
0.10µF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER71H154K1S1H03A
X7R
50
0.15µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER71H224K1S1H03A
X7R
50
0.22µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER71H334K1S1H03A
X7R
50
0.33µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER71H474K1S1H03A
X7R
50
0.47µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER71H684K2S1H03A
X7R
50
0.68µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDEC71H105K1S1H03A
X7S
50
1.0µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER71H105K2S1H03A
X7R
50
1.0µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDER71H155K2S1H03A
X7R
50
1.5µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDER71H225K2S1H03A
X7R
50
2.2µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDER71H335K3S1H03A
X7R
50
3.3µF ±10%
5.5
5.0
7.5
2.5
4.0
16.0 3S1
1500
RDEC71H475K2S1H03A
X7S
50
4.7µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDEC71H106K3S1H03A
X7S
50
10µF ±10%
5.5
5.0
7.5
2.5
4.0
16.0 3S1
1500
RDER72A221K0S1H03A
X7R
100
220pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A331K0S1H03A
X7R
100
330pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A471K0S1H03A
X7R
100
470pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
9 / 19
Reference only
Unit : mm
Customer Part Number
Murata Part Number
DC
Rated
T.C.
Cap. Cap. tol.
volt.
(V)
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
H0 Code (pcs)
RDER72A681K0S1H03A
X7R
100
680pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A102K0S1H03A
X7R
100
1000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A152K0S1H03A
X7R
100
1500pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A222K0S1H03A
X7R
100
2200pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A332K0S1H03A
X7R
100
3300pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A472K0S1H03A
X7R
100
4700pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A682K0S1H03A
X7R
100
6800pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A103K0S1H03A
X7R
100
10000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A153K0S1H03A
X7R
100
15000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A223K0S1H03A
X7R
100
22000pF ±10%
5.0
3.5
6.0
2.5
2.5
16.0 0S1
2000
RDER72A333K1S1H03A
X7R
100
33000pF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A473K1S1H03A
X7R
100
47000pF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A683K1S1H03A
X7R
100
68000pF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A104K1S1H03A
X7R
100
0.10µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A154K2S1H03A
X7R
100
0.15µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDER72A224K1S1H03A
X7R
100
0.22µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A334K1S1H03A
X7R
100
0.33µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A474K1S1H03A
X7R
100
0.47µF ±10%
5.0
3.5
5.0
2.5
3.15
16.0 1S1
2000
RDER72A684K2S1H03A
X7R
100
0.68µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDER72A105K2S1H03A
X7R
100
1.0µF ±10%
5.5
4.0
6.0
2.5
3.15
16.0 2S1
2000
RDEC72A155K3S1H03A
X7S
100
1.5µF ±10%
5.5
5.0
7.5
2.5
4.0
16.0 3S1
1500
RDEC72A225K3S1H03A
X7S
100
2.2µF ±10%
5.5
5.0
7.5
2.5
4.0
16.0 3S1
1500
RDER71E104K0M1H03A
X7R
25
0.10µF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDEC71E224K0M1H03A
X7S
25
0.22µF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDEC71E474K0M1H03A
X7S
25
0.47µF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDEC71E105K0M1H03A
X7S
25
1.0µF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDEC71E225K1M1H03A
X7S
25
2.2µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDEC71E475K2M1H03A
X7S
25
4.7µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDEC71E106K2M1H03A
X7S
25
10µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDEC71E226K3M1H03A
X7S
25
22µF ±10%
5.5
5.0
7.5
5.0
4.0
16.0 3M1
1500
RDEC71E476MWM1H03A
X7S
25
47µF ±20%
5.5
7.5
10.0
5.0
4.0
16.0 WM1
1500
RDER71H221K0M1H03A
X7R
50
220pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H331K0M1H03A
X7R
50
330pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H471K0M1H03A
X7R
50
470pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H681K0M1H03A
X7R
50
680pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H102K0M1H03A
X7R
50
1000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H152K0M1H03A
X7R
50
1500pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H222K0M1H03A
X7R
50
2200pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H332K0M1H03A
X7R
50
3300pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H472K0M1H03A
X7R
50
4700pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
10 / 19
Reference only
Unit : mm
Customer Part Number
Murata Part Number
DC
Rated
T.C.
Cap. Cap. tol.
volt.
(V)
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
H0 Code (pcs)
RDER71H682K0M1H03A
X7R
50
6800pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H103K0M1H03A
X7R
50
10000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H153K0M1H03A
X7R
50
15000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H223K0M1H03A
X7R
50
22000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H333K0M1H03A
X7R
50
33000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H473K0M1H03A
X7R
50
47000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H683K0M1H03A
X7R
50
68000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H104K0M1H03A
X7R
50
0.10µF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER71H154K1M1H03A
X7R
50
0.15µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER71H224K1M1H03A
X7R
50
0.22µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER71H334K1M1H03A
X7R
50
0.33µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER71H474K1M1H03A
X7R
50
0.47µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER71H684K2M1H03A
X7R
50
0.68µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDEC71H105K1M1H03A
X7S
50
1.0µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER71H105K2M1H03A
X7R
50
1.0µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDER71H155K2M1H03A
X7R
50
1.5µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDER71H225K2M1H03A
X7R
50
2.2µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDER71H335K3M1H03A
X7R
50
3.3µF ±10%
5.5
5.0
7.5
5.0
4.0
16.0 3M1
1500
RDEC71H475K2M1H03A
X7S
50
4.7µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDEC71H106K3M1H03A
X7S
50
10µF ±10%
5.5
5.0
7.5
5.0
4.0
16.0 3M1
1500
RDEC71H226MWM1H03A
X7S
50
22µF ±20%
5.5
7.5
10.0
5.0
4.0
16.0 WM1
1500
RDER72A221K0M1H03A
X7R
100
220pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A331K0M1H03A
X7R
100
330pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A471K0M1H03A
X7R
100
470pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A681K0M1H03A
X7R
100
680pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A102K0M1H03A
X7R
100
1000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A152K0M1H03A
X7R
100
1500pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A222K0M1H03A
X7R
100
2200pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A332K0M1H03A
X7R
100
3300pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A472K0M1H03A
X7R
100
4700pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A682K0M1H03A
X7R
100
6800pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A103K0M1H03A
X7R
100
10000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A153K0M1H03A
X7R
100
15000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A223K0M1H03A
X7R
100
22000pF ±10%
4.0
3.5
6.0
5.0
2.5
16.0 0M1
2000
RDER72A333K1M1H03A
X7R
100
33000pF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A473K1M1H03A
X7R
100
47000pF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A683K1M1H03A
X7R
100
68000pF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A104K1M1H03A
X7R
100
0.10µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A154K2M1H03A
X7R
100
0.15µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
11 / 19
Reference only
Unit : mm
Customer Part Number
Murata Part Number
DC
Rated
T.C.
Cap. Cap. tol.
volt.
(V)
Dimension (mm)
L
W
W1
F
T
Size Pack
Lead qty.
H0 Code (pcs)
RDER72A224K1M1H03A
X7R
100
0.22µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A334K1M1H03A
X7R
100
0.33µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A474K1M1H03A
X7R
100
0.47µF ±10%
4.5
3.5
5.0
5.0
3.15
16.0 1M1
2000
RDER72A684K2M1H03A
X7R
100
0.68µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDER72A105K2M1H03A
X7R
100
1.0µF ±10%
5.5
4.0
6.0
5.0
3.15
16.0 2M1
2000
RDEC72A155K3M1H03A
X7S
100
1.5µF ±10%
5.5
5.0
7.5
5.0
4.0
16.0 3M1
1500
RDEC72A225K3M1H03A
X7S
100
2.2µF ±10%
5.5
5.0
7.5
5.0
4.0
16.0 3M1
1500
RDEC72A475MWM1H03A
X7S
100
4.7µF ±20%
5.5
7.5
10.0
5.0
4.0
16.0 WM1
1500
12 / 19
Reference only
5.SPECIFICATIONS AND TEST METHODS
No.
Item
1
2
Appearance
Dimension and Marking
3
Dielectric
Strength
Between
Terminals
Body
Insulation
Specification
No defects or abnormalities
Within the specified dimensions and
Marking
No defects or abnormalities
No defects or abnormalities
4
Insulation
Resistance
(I.R.)
5
Capacitance
Within the specified tolerance
6
Dissipation Factor (D.F.)
X7R : 0.025 max.
X7S : 0.125 max.
7
8
Between
Terminals
Tensile
Strength
The capacitor should not be damaged when voltage
in Table is applied between the terminations for
1 to 5 seconds. (Charge/Discharge current 50mA.)
Rated voltage
Test voltage
DC25V・DC50V
DC100V
250% of the rated voltage
The capacitor is placed in a container with metal balls
of 1mm diameter so that each terminal, short-circuit,
is kept approximately 2mm from the balls, and
voltage in Table is impressed for 1 to 5 seconds
between capacitor terminals and metal balls.
(Charge/Discharge current 50mA.)
Rated voltage
Test voltage
DC25V・DC50V
DC100V
250% of the rated voltage
The insulation resistance should be measured with a
DC voltage not exceeding the rated voltage at normal
temperature and humidity and within 2 minutes of
charging. (Charge/Discharge current 50mA)
The capacitance, D.F. should be measured at 25C
at the frequency and voltage shown in the table.
Nominal Cap.
X7R : within 15%
X7S : within 22%
Capacitance
Temperature
Characteristics
Terminal
Strength
10,000M or 500MF min.
(Whichever is smaller)
Test Method
Visual inspection.
Visual inspection, Using Caliper.
Frequency
Voltage
C≦10μF
1±0.1kHz
AC1±0.2V(r.m.s.)
C＞10μF
120±24Hz
AC0.5±0.1V(r.m.s.)
The capacitance change should be measured after 5
min. at each specified temperature stage.
The ranges of capacitance change compared with the
25C value over the temperature ranges shown in the
table should be within the specified ranges.
Termination not to be broken or
loosened
Step
Temperature(C)
1
2
3
4
5
252
-553
252
1253
252
• Pretreatment
Perform a heat treatment at 150+0/-10C for one
hour and then set at *room condition for 242
hours.
As in the figure, fix the capacitor body, apply the
force gradually to each lead in the radial direction of
the capacitor until reaching 10N and then keep
applied the force for 101 seconds.
F
9
Vibration
Resistance
Bending
Strength
Termination not to be broken or
loosened
Each lead wire should be subjected to a force of
2.5N and then be bent 90° at the point of egress in
one direction. Each wire is then returned to the
original position and bent 90° in the opposite
direction at the rate of one bend per 2 to 3 seconds.
Appearance
No defects or abnormalities
Capacitance
Within the specified tolerance
D.F.
X7R : 0.025 max.
X7S : 0.125 max.
The capacitor should be subjected to a simple
harmonic motion having a total amplitude of 1.5mm,
the frequency being varied uniformly between the
approximate limits of 10Hz and 55Hz.
The frequency range, from 10Hz to 55Hz and return
to 10Hz, shall be traversed in approximately 1 minute.
This motion shall be applied for a period of 2 hours in
each 3 mutually perpendicular directions (total of 6
hours).
* “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa
ESRDE103C
13 / 19
Reference only
No.
10
Item
Solderability of Lead
Specification
Test Method
Solder is deposited on unintermittently
immersed portion in axial direction
covering 3/4 or more in circumferential
direction of lead wires.
11-1 Resistance
to Soldering
Heat
(NonPreheat)
Appearance
Capacitance
Change
Dielectric
Strength
(Between
terminals)
No defects or abnormalities
X7R : Within 7.5%
X7S : Within 10%
No defects
11-2 Resistance
to Soldering
Heat
(OnPreheat)
Appearance
No defects or abnormalities
Capacitance
Change
Dielectric
Strength
(Between
terminals)
X7R : Within 7.5%
X7S : Within 10%
No defects
Appearance
No defects or abnormalities
X7R : Within 7.5%
X7S : Within 10%
No defects
11-3 Resistance
to Soldering
Heat
(soldering
iron method)
12
13
Capacitance
Change
Dielectric
Strength
(Between
terminals)
Temperature Appearance
Cycle
Humidity
(Steady
State)
No defects or abnormalities
Capacitance
Change
X7R,X7S : Within12.5%
D.F.
X7R : 0.05 max.
X7S : 0.2 max.
I.R.
1,000M or 50M·F min.
(Whichever is smaller)
Dielectric
Strength
(Between
Terminals)
No defects or abnormalities
Appearance
Capacitance
Change
D.F.
No defects or abnormalities
X7R,X7S : Within 15%
I.R.
X7R : 0.05 max.
X7S : 0.2 max.
1,000M or 50M·F min.
(Whichever is smaller)
The terminal of capacitor is dipped into a solution of
ethanol (JIS K 8101) and rosin (JIS K 5902) (25%
rosin in weight propotion).Immerse in solder
solution for 20.5 seconds. In both cases the depth
of dipping is up to about 1.5 to 2mm from the
terminal body.
Temp. of solder :
2455C Lead Free Solder(Sn-3.0Ag-0.5Cu)
2355C H60A or H63A Eutectic Solder
The lead wires should be immersed in the melted
solder 1.5 to 2.0mm from the root of terminal at
2605C for 7.5+0/-1 seconds.
• Pretreatment
Capacitor should be stored at 150+0/-10C for one
hour, then place at *room condition for 242 hours
before initial measurement.
• Post-treatment
Capacitor should be stored for 242 hours at *room
condition.
First the capacitor should be stored at 120+0/-5C for
60+0/-5 seconds.
Then, the lead wires should be immersed in the
melted solder 1.5 to 2.0mm from the root of terminal at
2605C for 7.5+0/-1 seconds.
• Pretreatment
Capacitor should be stored at 150+0/-10C for one
hour, then place at *room condition for 242 hours
before initial measurement.
• Post-treatment
Capacitor should be stored for 242 hours at *room
condition.
Test condition
Termperature of iron-tip : 35010C
Soldering time : 3.50.5 seconds
Soldering position
Straight Lead:1.5 to 2.0mm from the root of terminal.
Crimp Lead:1.5 to 2.0mm from the end of bend.
• Pretreatment
Capacitor should be stored at 150+0/-10C for one
hour, then place at *room condition for 242 hours
before initial measurement.
• Post-treatment
Capacitor should be stored for 242 hours at *room
condition.
Repeat 5 cycles according to the 4 heat
treatments listed in the following table.
Set at *room condition for 242 hours, then
measure.
Step
1
2
3
4
Temp.
(C)
Min.
Operating
Temp. 3
Room
Temp.
Max.
Operating
Temp. 3
Room
Temp.
Time
(min.)
303
3 max.
303
3 max.
• Pretreatment
Perform a heat treatment at 150+0/-10C for one
hour and then set at *room condition for 242
hours.
Set the capacitor at 402C and relative
humidty 90 to 95% for 500+24/-0 hours.
Remove and set for 242 hours at *room condition ,
then measure.
• Pretreatment
Perform a heat treatment at 150+0/-10C for one
hour and then set at *room condition for 242
hours.
* “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa
ESRDE103C
14 / 19
Reference only
No.
14
Item
Humidity
Load
Specification
Appearance
No defects or abnormalities
Capacitance
Change
D.F.
X7R,X7S : Within15%
I.R.
15
High
Temperature
Load
Appearance
Capacitance
Change
D.F.
I.R.
16
Solvent
Resistance
X7R : 0.05 max.
X7S : 0.2 max.
500M or 25M·F min.
(Whichever is smaller)
No defects or abnormalities
X7R,X7S : Within15%
X7R : 0.05 max.
X7S : 0.2 max.
1,000M or 50 M·F min.
(Whichever is smaller)
Appearance
No defects or abnormalities
Marking
Legible
Test Method
Apply the rated voltage at 402C and relative
humidity of 90 to 95% for 500+24/-0 hours.
Remove and set for 242 hours at *room condition,
then measure.
(Charge/Discharge current 50mA)
• Pretreatment
Perform a heat treatment at 150+0/-10C for one
hour and then set at *room condition for 242
hours.
Apply 150% of the rated voltage at the maximum
operating temperature 3C for 1000+48/-0 hours.
Remove and set for 242 hours at *room condition ,
then measure.
(Charge/Discharge current 50mA)
• Pretreatment
Apply test voltage for one hour at test temperature.
Remove and set at *room condition for 242 hours.
The capacitor should be fully immersed, unagitated,
in reagent at 20 to 25C for 305 seconds and then
remove gently. Marking on the surface of the
capacitor shall immendiately be visually examined.
Reagent : Isopropyl alcohol
* “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa
ESRDE103C
15 / 19
Reference only
6. Packing specification
Bulk type (Packing style code : B)
1
2
The number of packing = Packing quantity n
The size of packing case and packing way
1 : Please refer to [Part number list].
2 : Standard n = 20 (bag)
Polyethylene bag
Partition
Note)
The outer package and the number of
outer packing be changed by the order
getting amount.
270 max.
125 max.
340 max.
Unit : mm
Ammo pack taping type (Packing style code : A)
A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.
When body of the capacitor is piled on other body under it.
The size of packing case and packing way
240 max.
Position of label
Unit : mm
340 max.
Hold down tape
Capacitor
51 max.
Base tape
Hold down
tape upper
EKBCRPE01
16 / 19
Reference only
7. Taping specification
7-1. Dimension of capacitors on tape
Inside crimp taping type < Lead code : M1 >
Pitch of component 12.7mm / Lead spacing 5.0mm
0
P
P2
h2
h1
S
Marking
t1
t2
W
W0
L
D0
W1
d
H0
F
P1
W2
e
P0
Unit : mm
Item
Code
Dimensions
Pitch of component
P
12.7+/-1.0
Pitch of sprocket hole
P0
12.7+/-0.2
Lead spacing
F
5.0+0.6/-0.2
Length from hole center to component center
P2
6.35+/-1.3
Length from hole center to lead
P1
3.85+/-0.7
Deviation along tape, left or right defect
S
0+/-2.0
Carrier tape width
W
18.0+/-0.5
Position of sprocket hole
W1
9.0+0/-0.5
H0
16.0+/-0.5
Lead distance between reference and bottom
plane
Remarks
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
0.5 max.
Protrusion length
Diameter of sprocket hole
D0
4.0+/-0.1
Lead diameter
d
0.50+/-0.05
Total tape thickness
t1
0.6+/-0.3
Total thickness of tape and lead wire
t2
1.5 max.
h1
h2
2.0 max.（Dimension code：W）
1.0 max.（except as above）
Portion to cut in case of defect
L
11.0+0/-1.0
Hold down tape width
W0
9.5 min.
Hold down tape position
W2
1.5+/-1.5
Coating extension on lead
e
Up to the end of crimp
Deviation across tape
ETP1M101
17 / 19
They include hold down tape thickness.
Reference only
Outside crimp taping type < Lead code : S1 >
Pitch of component 12.7mm / Lead spacing 2.5mm
P2
P
h1
0
h2
S
Marking
e
t1
t2
W0
L
D0
W
H0
d
W2
F
W1
P1
P0
Unit : mm
Item
Code
Dimensions
Pitch of component
P
12.7+/-1.0
Pitch of sprocket hole
P0
12.7+/-0.2
Lead spacing
F
2.5+0.4/-0.2
Length from hole center to component center
P2
6.35+/-1.3
Length from hole center to lead
P1
3.85+/-0.7
Deviation along tape, left or right defect
S
0+/-2.0
Carrier tape width
W
18.0+/-0.5
Position of sprocket hole
W1
9.0+0/-0.5
H0
16.0+/-0.5
Lead distance between reference and bottom
plane
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
0.5 max.
Protrusion length
Diameter of sprocket hole
D0
4.0+/-0.1
Lead diameter
d
0.50+/-0.05
Total tape thickness
t1
0.6+/-0.3
Total thickness of tape and lead wire
t2
1.5 max.
Deviation across tape
Remarks
h1
h2
They include hold down tape thickness.
1.0 max.
Portion to cut in case of defect
L
11.0+0/-1.0
Hold down tape width
W0
9.5 min.
Hold down tape position
W2
1.5+/-1.5
Coating extension on lead
e
Up to the end of crimp
ETP1S101
18 / 19
Reference only
7-2. Splicing way of tape
1) Adhesive force of tape is over 3N at test condition as below.
W
Hold down tape
Base tape
2) Splicing of tape
a) When base tape is spliced
Base tape shall be spliced by cellophane tape.
(Total tape thickness shall be less than 1.05mm.)
Progress direction
in production line
Hold down tape
Base tape
About 30 to 50
Cellophane tape
No lifting for the direction of
progressing
Unit : mm
b) When hold down tape is spliced
Hold down tape shall be spliced with overlapping.
(Total tape thickness shall be less than 1.05mm.)
ape are spliced
Base tape and adhesive tape shall be spliced with splicing tape.
20 to 30
Hold down tape
Progress direction
in production line
Base tape
Unit : mm
c) When both tape are spliced
Base tape and hold down tape shall be spliced with splicing tape.
ETP2R01
19 / 19
Appendix
EU RoHS and Halogen Free
This products of the following crresponds to EU RoHS and Halogen Free
(1) RoHS
EU RoHs 2011/65/EC compliance
maximum concentration values tolerated by weight in homogeneous materials
・1000 ppm maximum Lead
・1000 ppm maximum Mercury
・100 ppm maximum Cadmium
・1000 ppm maximum Hexavalent chromium
・1000 ppm maximum Polybrominated biphenyls (PBB)
・1000 ppm maximum Polybrominated diphenyl ethers (PBDE)
(2) Halogen-Free
The International Electrochemical Commission’s (IEC) Definition
of Halogen-Free (IEC 61249-2-21) compliance
・900 ppm maximum chlorine
・900 ppm maximum bromine
・1500 ppm maximum total chlorine and bromine
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Murata:
RDER71E223K0K1C03B RDEC71E226K3M1H03A RDEC71E226K3S1H03A RDEC71E475K2S1H03A
RDEC71H475K2M1H03A RDEC72A225K3S1H03A RDER71H102K0S1H03A RDER71H103K0M1H03A
RDER71H104K0S1H03A RDER71H153K0S1H03A RDER71H221K0S1H03A RDER71H222K0M1H03A
RDER71H224K1M1H03A RDER71H225K2M1H03A RDER71H331K0M1H03A RDER71H332K0M1H03A
RDER71H333K0S1H03A RDER71H471K0M1H03A RDER71H473K0M1H03A RDER71H681K0M1H03A
RDER71H682K0M1H03A RDER71H684K2S1H03A RDER72A102K0M1H03A RDER72A105K2M1H03A
RDEC71E224K0S1H03A RDEC71E225K1M1H03A RDEC71E476MWM1H03A RDEC72A155K3S1H03A
RDER71H103K0S1H03A RDER71H154K1S1H03A RDER71H221K0M1H03A RDER71H224K1S1H03A
RDER71H334K1S1H03A RDER71H335K3M1H03A RDER71H681K0S1H03A RDER71H682K0S1H03A
RDER71H684K2M1H03A RDER72A152K0S1H03A RDER72A154K2M1H03A RDER72A154K2S1H03A
RDER72A223K0M1H03A RDER72A223K0S1H03A RDER72A224K1S1H03A RDER72A333K1S1H03A
RDER72A472K0M1H03A RDER72A473K1M1H03A RDER72A681K0M1H03A RDER72A153K0S1H03A
RDER72A221K0M1H03A RDER72A222K0M1H03A RDER72A332K0S1H03A RDER72A474K1S1H03A
RDER72A681K0S1H03A RDER72A683K1S1H03A RDEC71E105K0S1H03A RDEC71E106K2S1H03A
RDEC71E474K0M1H03A RDEC71H106K3M1H03A RDEC72A155K3M1H03A RDEC72A225K3M1H03A
RDER71H152K0S1H03A RDER71H154K1M1H03A RDER71H155K2M1H03A RDER71H223K0S1H03A
RDER71H332K0S1H03A RDER71H683K0M1H03A RDER72A103K0S1H03A RDER72A105K2S1H03A
RDER72A153K0M1H03A RDER72A221K0S1H03A RDER72A224K1M1H03A RDER72A331K0M1H03A
RDER72A331K0S1H03A RDER72A332K0M1H03A RDER72A333K1M1H03A RDER72A471K0M1H03A
RDER72A472K0S1H03A RDER72A473K1S1H03A RDER72A474K1M1H03A RDEC71E106K2M1H03A
RDEC71E225K1S1H03A RDEC71E475K2M1H03A RDEC72A475MWM1H03A RDER71E104K0M1H03A
RDER71H105K2M1H03A RDER71H152K0M1H03A RDER71H222K0S1H03A RDER71H223K0M1H03A
RDER71H225K2S1H03A RDER71H333K0M1H03A RDER71H334K1M1H03A RDER71H471K0S1H03A
RDER71H472K0M1H03A RDER71H473K0S1H03A RDER71H683K0S1H03A RDER72A102K0S1H03A
RDER72A103K0M1H03A RDER72A222K0S1H03A RDER72A334K1M1H03A RDER72A334K1S1H03A
工商网监
湘ICP备2023018690号
