RHS7G2A272J1M2H01A

Reference Specification 200℃ Operation Leaded MLCC for Automotive (Powertrain/Safety) RHS Series Product specifications in this catalog are as of Oct. 2023, and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering.Please read rating and Cautions first. ＜Reference＞Please kindly use our website. Please refer to the product information page for more information on ceramic capacitors.→ Ceramic capacitor product information Various data can be obtained directly from the product search.→ Product search (SMD) / Product search (Lead Type) Reference only CAUTION 　　 1. OPERATING VOLTAGE 1. Do not apply a voltage to the capacitor that exceeds the rated voltage as called out in the specifications. 1-1. Applied voltage between the terminals of a capacitor shall be less than or equal to the rated voltage. (1) When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated DC voltage. When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed the rated DC voltage. (2) Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC voltage. Typical Voltage Applied to the DC Capacitor DC Voltage V0-p DC+AC Voltage V0-p AC Voltage Vp-p Pulse Voltage Vp-p (E: Maximum possible applied voltage.) 1-2. Influence of over voltage Over voltage that is applied to the capacitor may result in an electrical short circuit caused by the breakdown of the internal dielectric layers. The time duration until breakdown depends on the applied voltage and the ambient temperature. 2. Use a safety standard certified capacitor in a power supply input circuit (AC filter), as it is also necessary to consider the withstand voltage and impulse withstand voltage defined for each device. 　　 2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.), applied voltage should be the load such as self-generated heat is within 20 °C on the condition of atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1 capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s characteristics and reliability. 3. FAIL-SAFE Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. 4. OPERATING AND STORAGE ENVIRONMENT The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months. Use capacitors within 6 months after delivered. Check the solderability after 6 months or more. EGLEDMNO03A 1/17 Reference only CAUTION 5. VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use. Excessive shock or vibration may cause to fatigue destruction of lead wires mounted on the circuit board. If necessary, take measures to hold a capacitor on the circuit boards by adhesive, molding resin or coating and other. Please confirm there is no influence of holding measures on the product with an intended equipment. 6. SOLDERING When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. Please verify that the soldering process does not affect the quality of capacitors. 6-1. Flow Soldering Soldering temperature Soldering time Preheating temperature Preheating time : 260 ℃ max. : 7.5 s max. : 120 ℃ max. : 60 s max. 6-2. Soldering Iron Temperature of iron-tip Soldering iron wattage Soldering time : 350 ℃ max. : 60 W max. : 3.5 s max. 7. BONDING AND RESIN MOLDING, RESIN COAT In case of bonding, molding or coating this product, verify that these processes do not affect the quality of capacitor by testing the performance of a bonded or molded product in the intended equipment. In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short circuit. The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or ceramic element cracking of a capacitor in a temperature cycling. 8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile. So please be careful not to give it mechanical stress. Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. EGLEDMNO03A 2/17 Reference only CAUTION 9. LIMITATION OF APPLICATIONS The products listed in the specification(hereinafter the product(s) is called as the “Product(s)”) are designed and manufactured for applications specified in the specification. (hereinafter called as the “Specific Application”) We shall not warrant anything　in connection with the Products including fitness, performance, adequateness, safety, or quality, in the case of applications listed in from (1) to (11) written at the end of this precautions, which may generally require high performance, function, quality, management of production or safety. Therefore, the Product shall be applied in compliance with the specific application. WE DISCLAIM ANY LOSS AND DAMAGES ARISING FROM OR IN CONNECTION WITH THE PRODUCTS INCLUDING BUT NOT LIMITED TO THE CASE SUCH LOSS AND DAMAGES CAUSED BY THE UNEXPECTED ACCIDENT, IN EVENT THAT (i) THE PRODUCT IS APPLIED FOR THE PURPOSE WHICH IS NOT SPECIFIED AS THE SPECIFIC APPLICATION FOR THE PRODUCT, AND/OR (ii) THE PRODUCT IS APPLIED FOR ANY FOLLOWING APPLICATION PURPOSES FROM (1) TO (11) (EXCEPT THAT SUCH APPLICATION PURPOSE IS UNAMBIGUOUSLY SPECIFIED AS SPECIFIC APPLICATION FOR THE PRODUCT IN OUR CATALOG　SPECIFICATION FORMS, DATASHEETS, OR OTHER DOCUMENTS OFFICIALLY ISSUED BY US*) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Aircraft equipment Aerospace equipment Undersea equipment Power plant control equipment Medical equipment Transportation equipment Traffic control equipment Disaster prevention/security equipment Industrial data-processing equipment Combustion/explosion control equipment Equipment with complexity and/or required reliability equivalent to the applications listed in the above. For exploring information of the Products which will be compatible with the particular purpose other than those specified in the specification, please contact our sales offices, distribution agents, or trading companies with which you make a deal, or via our web contact form. Contact form: https://www.murata.com/contactform *We may design and manufacture particular Products for applications listed in (1) to (11). Provided that, in such case we shall unambiguously specify such Specific Application in the specification without any exception. Therefore, any other documents and/or performances, whether exist or non-exist, shall not be deemed as the evidence to imply that we accept the applications listed in (1) to (11). EGLEDMNO03A 3/17 Reference only CAUTION NOTICE 1. CLEANING (ULTRASONIC CLEANING) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity : Output of 20 watts per liter or less. Rinsing time : 5 min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 2. SOLDERING AND MOUNTING Insertion of the Lead Wire • When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire. • Insert the lead wire into the PCB with a distance appropriate to the lead space. 3. CAPACITANCE CHANGE OF CAPACITORS • Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.) Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant circuit. Please contact us if you need a detail information. NOTE 1. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2. You are requested not to use our product deviating from this product specification. EGLEDMNO03A 4/17 Reference only 1. Application This product specification is applied to Leaded MLCC RHS series. 1. Specific applications: ･Automotive powertrain/safety equipment: Products that can be used for automotive equipment related to running, turning, stopping, safety devices, etc., or equipment whose structure, equipment, and performance are legally required to meet technical standards for safety assurance or environmental protection. ･Automotive infotainment/comfort equipment: Products that can be used for automotive equipment such as car navigation systems and car audio systems that do not directly relate to human life and whose structure, equipment, and performance are not specifically required by law to meet technical standards for safety assurance or environmental protection. ･Medial Equipment [GHTF A/B/C] except for Implant Equipment: Products suitable for use in medical devices designated under the GHTF international classifications as Class A or Class B (the functions of which are not directly involved in protection of human life or property) or in medical devices other than implants designated under the GHTF international classifications as Class C (the malfunctioning of which is considered to pose a comparatively high risk to the human body). 2.Unsuitable Application: Applications listed in “Limitation of applications” in this product specification. 2. Rating • Applied maximum temperature up to 200°C Note : Maximum accumulative time to 200°C is within 2000 hours. • Part Number Configuration ex.) RHS Series • Series 2A 332 J 1 A2 Temperature 7G Rated Capacitance Capacitance Dimension Lead Individual Characteristics Voltage Style Specification Code RHS Tolerance (LxW) H01 B Package Content Epoxy coated, 200°C max. • Temperature Characteristics Code Temp. Char. Temp. Range Temp.coef. 7G CCG (Murata code) -55～25°C 25～125°C 125～200°C 0+30/-72ppm/°C 0+/-30ppm/°C 0+72/-30ppm/°C TEIKAKU 5/17 Standard Temp. Operating Temp. Range 25°C -55～200°C Reference only • Rated Voltage Code 2A Rated voltage DC100V When the product temperature exceeds 150°C, please use this product within the voltage and temperature derated conditions in the figure below. • Capacitance The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF. ex.) In case of 332 . 33 × 102 = 3300 pF • Capacitance Tolerance Code Capacitance Tolerance J +/-5% • Dimension (LxW) Please refer to [ Part number list ]. • Lead Style *Lead wire is "solder coated CP wire". Code Lead Style A2 Straight type DG Straight taping type K1 Inside crimp type M2 Inside crimp taping type Lead spacing (mm) 2.5+/-0.8 2.5+0.4/-0.2 5.0+/-0.8 5.0+0.6/-0.2 • Individual Specification Murata’s control code. Please refer to [ Part number list ]. • Package Code A B Package Taping type of Ammo Bulk type TEIKAKU 6/17 Reference only 3. Marking Temp. char. Capacitance Capacitance tolerance (Ex.) Rated voltage Dimension code 0,1 : Letter code : 4 (CCG char.) : 3 digit numbers : Code DC100V 4 101J TEIKAKU 7/17 Reference only 4. Part number list Unit : mm Customer Part Number Murata Part Number T.C. DC Rated Volt. (V) Cap. Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack qty. (LxW) Lead Style (pcs) RHS7G2A101J0A2H01B CCG 100 100pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A121J0A2H01B CCG 100 120pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A151J0A2H01B CCG 100 150pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A181J0A2H01B CCG 100 180pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A221J0A2H01B CCG 100 220pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A271J0A2H01B CCG 100 270pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A331J0A2H01B CCG 100 330pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A391J0A2H01B CCG 100 390pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A471J0A2H01B CCG 100 470pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A561J0A2H01B CCG 100 560pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A681J0A2H01B CCG 100 680pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A821J0A2H01B CCG 100 820pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A102J0A2H01B CCG 100 1000pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A122J0A2H01B CCG 100 1200pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A152J0A2H01B CCG 100 1500pF ±5% 3.9 3.5 - 2.5 2.6 0A2 500 RHS7G2A182J1A2H01B CCG 100 1800pF ±5% 4.2 3.5 - 2.5 2.8 1A2 500 RHS7G2A222J1A2H01B CCG 100 2200pF ±5% 4.2 3.5 - 2.5 2.8 1A2 500 RHS7G2A272J1A2H01B CCG 100 2700pF ±5% 4.2 3.5 - 2.5 2.8 1A2 500 RHS7G2A332J1A2H01B CCG 100 3300pF ±5% 4.2 3.5 - 2.5 2.8 1A2 500 RHS7G2A101J0K1H01B CCG 100 100pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A121J0K1H01B CCG 100 120pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A151J0K1H01B CCG 100 150pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A181J0K1H01B CCG 100 180pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A221J0K1H01B CCG 100 220pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A271J0K1H01B CCG 100 270pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A331J0K1H01B CCG 100 330pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A391J0K1H01B CCG 100 390pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A471J0K1H01B CCG 100 470pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A561J0K1H01B CCG 100 560pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 500 RHS7G2A681J0K1H01B CCG 100 680pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 RHS7G2A821J0K1H01B CCG 100 820pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A102J0K1H01B CCG 100 1000pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A122J0K1H01B CCG 100 1200pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A152J0K1H01B CCG 100 1500pF ±5% 3.9 3.5 6.0 5.0 2.6 0K1 500 RHS7G2A182J1K1H01B CCG 100 1800pF ±5% 4.2 3.5 5.0 5.0 2.8 1K1 500 RHS7G2A222J1K1H01B CCG 100 2200pF ±5% 4.2 3.5 5.0 5.0 2.8 1K1 500 RHS7G2A272J1K1H01B CCG 100 2700pF ±5% 4.2 3.5 5.0 5.0 2.8 1K1 500 RHS7G2A332J1K1H01B CCG 100 3300pF ±5% 4.2 3.5 5.0 5.0 2.8 1K1 500 PNLIST 8/17 Reference only Unit : mm Customer Part Number PNLIST Murata Part Number T.C. DC Rated Volt. (V) Cap. Cap. Tol. Dimension (mm) L W W1 F T Dimension Pack qty. (LxW) H/H0 Lead Style (pcs) RHS7G2A101J0DGH01A CCG 100 100pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A121J0DGH01A CCG 100 120pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A151J0DGH01A CCG 100 150pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A181J0DGH01A CCG 100 180pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A221J0DGH01A CCG 100 220pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A271J0DGH01A CCG 100 270pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A331J0DGH01A CCG 100 330pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A391J0DGH01A CCG 100 390pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A471J0DGH01A CCG 100 470pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A561J0DGH01A CCG 100 560pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A681J0DGH01A CCG 100 680pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A821J0DGH01A CCG 100 820pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A102J0DGH01A CCG 100 1000pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A122J0DGH01A CCG 100 1200pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A152J0DGH01A CCG 100 1500pF ±5% 3.9 3.5 - 2.5 2.6 20.0 0DG 2000 RHS7G2A182J1DGH01A CCG 100 1800pF ±5% 4.2 3.5 - 2.5 2.8 20.0 1DG 2000 RHS7G2A222J1DGH01A CCG 100 2200pF ±5% 4.2 3.5 - 2.5 2.8 20.0 1DG 2000 RHS7G2A272J1DGH01A CCG 100 2700pF ±5% 4.2 3.5 - 2.5 2.8 20.0 1DG 2000 RHS7G2A332J1DGH01A CCG 100 3300pF ±5% 4.2 3.5 - 2.5 2.8 20.0 1DG 2000 RHS7G2A101J0M2H01A CCG 100 100pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A121J0M2H01A CCG 100 120pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A151J0M2H01A CCG 100 150pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A181J0M2H01A CCG 100 180pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A221J0M2H01A CCG 100 220pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A271J0M2H01A CCG 100 270pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A331J0M2H01A CCG 100 330pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A391J0M2H01A CCG 100 390pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A471J0M2H01A CCG 100 470pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A561J0M2H01A CCG 100 560pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A681J0M2H01A CCG 100 680pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A821J0M2H01A CCG 100 820pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A102J0M2H01A CCG 100 1000pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A122J0M2H01A CCG 100 1200pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A152J0M2H01A CCG 100 1500pF ±5% 3.9 3.5 6.0 5.0 2.6 20.0 0M2 2000 RHS7G2A182J1M2H01A CCG 100 1800pF ±5% 4.2 3.5 5.0 5.0 2.8 20.0 1M2 2000 RHS7G2A222J1M2H01A CCG 100 2200pF ±5% 4.2 3.5 5.0 5.0 2.8 20.0 1M2 2000 RHS7G2A272J1M2H01A CCG 100 2700pF ±5% 4.2 3.5 5.0 5.0 2.8 20.0 1M2 2000 RHS7G2A332J1M2H01A CCG 100 3300pF ±5% 4.2 3.5 5.0 5.0 2.8 20.0 1M2 2000 9/17 Reference only 5. Specification Test Item No. 1 Specification Test Method (Compliant Standard:AEC-Q200) Pre-and Post-Stress - Electrical Test 2 High Appearance Temperature 3 5 6 Sit the capacitor for 1000±12 hours at 200±5°C. Let sit for 24±2 hours at *room condition, then measure. Exposure Capacitance Within ±3% or ±0.3pF (Storage) Change (Whichever is larger) Q Q ≧ 350 Temperature I.R. 1,000MΩ min. Appearance No defects or abnormalities except color Perform the 1000 cycles according to the four heat treatments listed in change of outer coating the following table. Let sit for 24±2 hours at *room condition, then measure. Cycling 4 No defects or abnormalities except color change of outer coating. Capacitance Within ±5% or ±0.5pF Change (Whichever is larger) Q Q ≧ 350 I.R. 1,000MΩ min. 1 2 3 4 Temp. (°C) -55+0/-3 Room Temp. 200+5/-0 Room Temp. Time (min.) 15±3 1 15±3 1 Step Moisture Appearance No defects or abnormalities. Apply the 24 hours heat (25 to 65°C) and humidity (80 to 98%) Resistance Capacitance Within ±5% or ± 0.5pF treatment shown below, 10 consecutive times. Let sit for 24±2 hours at *room condition, then measure. Change (Whichever is larger) Q Q ≧ 200 I.R. 500MΩ min. Biased Appearance No defects or abnormalities. Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor) Humidity Capacitance Within ±5% or ± 0.5pF at 85±3°C and 80 to 85% humidity for 1000±12 hours. Operational Change (Whichever is larger) Remove and let sit for 24±2 hours at *room condition, then measure. Q Q ≧ 200 The charge/discharge current is less than 50mA. I.R. 500MΩ min. Appearance Life No defects or abnormalities except color Apply voltage in Table for 1,000±12h at 200±5°C. change of outer coating. Let sit for 24±2 hours at *room condition, then measure. The charge/discharge current is less than 50mA. Capacitance Within ±3% or ±0.3pF Change (Whichever is larger) Q Q ≧ 350 I.R. 1,000MΩ min. Capacitance Test Voltage 100pF-1000pF 50% of the rated voltage 1200pF-3300pF 25% of the rated voltage 7 External Visual No defects or abnormalities. Visual inspection. 8 Physical Dimension Within the specified dimensions. Using calipers and micrometers. 9 Marking 10 Resistance to Solvents To be easily legible. Visual inspection. Appearance No defects or abnormalities. Per MIL-STD-202 Method 215 Capacitance Within the specified tolerance. Q Q ≧ 1,000 I.R. 10,000MΩ min. Solvent 1 : 1 part (by volume) of isopropyl alcohol 3 parts (by volume) of mineral spirits Solvent 2 : Terpene defluxer Solvent 3 : 42 parts (by volume) of water 1part (by volume) of propylene glycol monomethyl ether 1 part (by volume) of monoethanolamine * “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa ESRH05D 10/17 Reference only Test Item No. 11 Mechanical Shock Appearance Specification Test Method (Compliant Standard:AEC-Q200) No defects or abnormalities. Three shocks in each direction should be applied along 3 Capacitance Within the specified tolerance. mutually perpendicular axes of the test specimen (18 shocks). Q Q ≧ 1,000 The specified test pulse should be Half-sine and should have a Appearance No defects or abnormalities. The capacitor should be subjected to a simple harmonic motion Capacitance Within the specified tolerance. having a total amplitude of 1.5mm, the frequency being varied Q Q ≧ 1,000 uniformly between the approximate limits of 10 and 2000Hz. duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s. 12 Vibration The frequency range, from 10 to 2000Hz and return to 10Hz, should be traversed in approximately 20 min. This motion should be applied for 12 items in each 3 mutually perpendicular directions (total of 36 times). 13-1 Resistance to Appearance No defects or abnormalities. The lead wires should be immersed in the melted solder 1.5 to 2.0mm from the root of terminal at 260±5°C for 10±1 seconds. Soldering Capacitance Within ±2.5% or ±0.25pF Heat Change (Whichever is larger) (Non- Dielectric No defects. Preheat) Strength • Post-treatment Capacitor should be stored for 24±2 hours at *room condition. (Between terminals) 13-2 Resistance to Appearance Soldering Capacitance No defects or abnormalities. First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds. Within ±2.5% or ±0.25pF Then, the lead wires should be immersed in the melted solder 1.5 to 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds. Heat Change (Whichever is larger) (On- Dielectric No defects. Preheat) Strength • Post-treatment (Between Capacitor should be stored for 24±2 hours at *room condition. terminals) 13-3 Resistance to Appearance No defects or abnormalities. Test condition Soldering Capacitance Within ±2.5% or ±0.25pF Temperature of iron-tip : 350±10°C Heat Change (Whichever is larger) Soldering time : 3.5±0.5 seconds (soldering Dielectric No defects. iron method) Strength Straight Lead : 1.5 to 2.0mm from the root of terminal. (Between Crimp Lead : 1.5 to 2.0mm from the end of lead bend. Soldering position terminals) • Post-treatment Capacitor should be stored for 24±2 hours at *room condition. 14 Thermal Shock 15 16 ESD Solderability Appearance No defects or abnormalities. Perform the 300 cycles according to the two heat treatments listed in the Capacitance Within ±5% or ±0.5pF following table (Maximum transfer time is 20 seconds.). Change (Whichever is larger) Let sit for 24±2 hours at *room condition, then measure. Q Q ≧ 350 I.R. 1,000MΩ min. Appearance No defects or abnormalities. Capacitance Within the specified tolerance. Q Q ≧ 1,000 I.R. 10,000MΩ min. Step 1 2 Temp. (°C) -55+0/-3 200+5/-0 Time (min.) 15±3 15±3 Per AEC-Q200-002 Lead wire should be soldered with The terminal of capacitor is dipped into a solution of rosin uniform coating on the axial direction over ethanol (25% rosin in weight propotion). 95% of the circumferential direction. Immerse in solder solution for 2±0.5 seconds. In both cases the depth of dipping is up to about 1.5 to 2mm from the terminal body. Temp. of solder : 245±5°C (Sn-3.0Ag-0.5Cu) * “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa ESRH05D 11/17 Reference only Test Item No. 17 Electrical Appearance Specification Test Method (Compliant Standard:AEC-Q200) No defects or abnormalities. Visual inspection. Characte- Capacitance Within the specified tolerance. The capacitance, Q should be measured at 25°C at the frequency rization Q Q ≧ 1,000 and voltage shown in the table. Insulation Room Resistance Temperature 10,000MΩ min. Nominal Cap. Frequency Voltage C ≦ 1000pF 1±0.1MHz AC0.5 to 5V(r.m.s.) C > 1000pF 1±0.1kHz AC1±0.2V(r.m.s.) The insulation resistance should be measured at 25±3 °C with a DC voltage not exceeding the rated voltage at normal temperature (I.R.) and humidity and within 2 min. of charging. (Charge/Discharge current ≦ 50mA.) High 20MΩ min. The insulation resistance should be measured at 200±5°C with a Temperature DC voltage not exceeding voltage in Table and within 2 min. of charging. (Charge/Discharge current ≦ 50mA.) Capacitance 100pF-1000pF 1200pF-3300pF Dielectric Between Strength Terminals No defects or abnormalities. Test Voltage 50% of the rated voltage 25% of the rated voltage The capacitor should not be damaged when voltage in Table is applied between the terminations for 1 to 5 seconds. (Charge/Discharge current ≦ 50mA.) Terminal To External Resin No defects or abnormalities. Rated Voltage Test Voltage DC100V 300% of the rated voltage The capacitor is placed in a container with metal balls of 1mm diameter so that each terminal, short-circuit, is kept approximately 2mm from the balls as shown in the figure, Approx. 2mm and voltage in table is impressed for 1 to 5 seconds between capacitor terminals and metal balls. (Charge/Discharge current ≦ 50mA.) 18 Terminal Tensile Strength Strength Termination not to be broken or loosened. Rated Voltage Test Voltage DC100V 250% of the rated voltage Metal balls As in the figure, fix the capacitor body, apply the force gradually to each lead in the radial direction of the capacitor until reaching 10N and then keep the force applied for 10±1 seconds. F ↓ Bending Termination not to be broken or loosened. Strength Each lead wire should be subjected to a force of 2.5N and then be bent 90° at the point of egress in one direction. Each wire is then returned to the original position and bent 90° in the opposite direction at the rate of one bend per 2 to 3 seconds. 19 Capacitance Within the specified Tolerance. Temperature 0+30/-72ppm/°C (-55 to 25°C) Characteristics 0±30ppm/°C (25 to 125°C) The capacitance change should be measured after 5min. at each specified temperature step. Step 0+72/-30ppm/°C (125 to 200°C) Temperature(°C) 1 25±2 2 -55±3 3 25±2 4 200±5 5 25±2 The temperature coefficient is determined using the capacitance measured in step 3 as a reference. When cycling the temperature sequentially from step 1 through 5 (-55°C to 150°C) the capacitance should be within the specified tolerance for the temperature coefficient and capacitance change as Table A. The capacitance drift is calculated by dividing the differences between the maximum and minimum measured values in the step 1, 3 and 5 by the capacitance value in step 3. * “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa ESRH05D 12/17 Reference only 6. Packing specification ・Bulk type (Packing style code : B) The size of packing case and packing way Plastic bag Partition 270 max. 125 max. Unit : mm 340 max. The number of packing = *1 Packing quantity × *2 n *1 : Please refer to [Part number list]. *2 : Standard n = 20 (bag) Note) The outer package and the number of outer packing be changed by the order getting amount. JKBCRPE02 13/17 Reference only ・Ammo pack taping type (Packing style code : A) 　　　　　　A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case. 　　　　　　When body of the capacitor is piled on other body under it. The size of packing case and packing way 240 max. Position of label 340 max. Unit : mm 51 max. Hold down tape Capacitor Base tape Hold down tape upper EKTRPE01 14/17 Reference only 7. Taping specification 7-1. Dimension of capacitors on tape Straight taping type < Lead Style : DG > Pitch of component 12.7mm / Lead spacing 2.5mm P △h1 W2 Φd H F t2 P0 t1 W W0 ΦD0 L △S △h2 Marking e P1 0 W1 P2 Unit : mm Item Code Dimensions Pitch of component P 12.7+/-1.0 Pitch of sprocket hole P0 12.7+/-0.2 F 2.5+0.4/-0.2 P2 6.35+/-1.3 Length from hole center to lead P1 5.1+/-0.7 Deviation along tape, left or right defect ΔS 0+/-2.0 Carrier tape width W 18.0+/-0.5 Position of sprocket hole W1 9.0+0/-0.5 H 20.0+/-0.5 Lead spacing Length from hole center to component center Lead distance between reference and bottom plane Protrusion length Diameter of sprocket hole ΦD0 4.0+/-0.1 Φd 0.5+/-0.05 Total tape thickness t1 0.6+/-0.3 t2 1.5 max. Deviation across tape Portion to cut in case of defect Δh1 1.0 max. Δh2 L 11.0+0/-1.0 Hold down tape width W0 9.5 min. Hold down tape position W2 1.5+/-1.5 e 2.0 max. Coating extension on lead Deviation of progress direction They include deviation by lead bend Deviation of tape width direction 0.5 max. Lead diameter Total thickness of tape and lead wire Remarks ETP1DBG01A 15/17 They include hold down tape thickness Reference only Inside crimp taping type < Lead Style : M2 > Pitch of component 12.7mm / Lead spacing 5.0mm Unit : mm Item Code Dimensions Pitch of component P 12.7+/-1.0 Pitch of sprocket hole P0 12.7+/-0.2 F 5.0+0.6/-0.2 P2 6.35+/-1.3 Length from hole center to lead P1 3.85+/-0.7 Deviation along tape, left or right defect ΔS 0+/-2.0 Carrier tape width W 18.0+/-0.5 Position of sprocket hole W1 9.0+0/-0.5 Lead distance between reference and bottom plane H0 20.0+/-0.5 Lead spacing Length from hole center to component center Protrusion length Diameter of sprocket hole ΦD0 4.0+/-0.1 Φd 0.5+/-0.05 Total tape thickness t1 0.6+/-0.3 t2 1.5 max. Deviation across tape Portion to cut in case of defect They include deviation by lead bend Deviation of tape width direction They include hold down tape thickness Δh1 　　　2.0 max. (Dimension code : W) Δh2 　　　1.0 max. (except as above) L 11.0+0/-1.0 Hold down tape width W0 9.5 min. Hold down tape position W2 1.5+/-1.5 Coating extension on lead Deviation of progress direction 0.5 max. Lead diameter Total thickness of tape and lead wire Remarks e Up to the end of crimp ETP1M201A 16/17 Reference only 　　7-2. Splicing way of tape 1) Adhesive force of tape is over 3N at test condition as below. W Hold down tape Base tape 2) Splicing of tape 　　　a) When base tape is spliced •Base tape shall be spliced by cellophane tape. (Total tape thickness shall be less than 1.05mm.) Progress direction in production line Hold down tape Base tape No lifting for the direction of progressing About 30 to 50 Cellophane tape Unit : mm 　　　b) When hold down tape is spliced 　　　 •Hold down tape shall be spliced with overlapping. (Total tape thickness shall be less than 1.05mm.) 20 to 30 Progress direction in production line Hold down tape Base tape Unit : mm 　　　c) When both tape are spliced •Base tape and hold down tape shall be spliced with splicing tape. ETP2R01 17/17