SF2039B

SF2039B • • • • • Designed for SDARS IF Receiver Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case Differential or Single Ended Input and Output Complies with Directive 2002/95/EC (RoHS) 72.540 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 Max Soldering Profile °C 265°C for 10 s SMP-03 Electrical Characteristics Characteristic Sym Nominal Center Frequency Passband Insertion Loss 1dB Passband 15dB Bandwidth 30dB Bandwidth Amplitude Ripple over fc ±1.85 MHz Group Delay Variation over fc ±1.85 MHz Rejection 50 to 66.48 MHz 66.48 to 68.08 MHz 77.30 to 78.60 MHz 78.60 to 86.50 MHz 86.50 to 91.50 MHz 91.50 to 100.00 MHz Operating Temperature Range Frequency Temperature Coefficient Differential Input Differential Output Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 fC IL BW1 BW15 BW30 Notes Min 1 3.7 1 GDV 1, 3 TA FTC 1 6 40 38 38 40 45 45 -40 Typ 72.540 10.5 4.0 6.5 7.5 0.5 60 47 43 42 44 50 55 Max 12.5 6.7 7.7 1.3 150 Units MHz dB MHz MHz MHz dBP-P nsP-P dB +85 °C -18 ppm/°C 175 ohms 1000 ohms SMP-03 7 x 5 mm Nominal Footprint RFM SF2039B YYWWS Electrical Connections Connection Port 1 Hot Port 1 Ground Return Port 2 Hot Port 2 Ground Return Case Ground Terminals 10 1 5 6 All Others ©2010-2014 byMurata Murata Electronics N.A., Inc. Copyright © Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 1 of 7 www.murata.com CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. 2. 3. 4. 5. 6. 7. 8. 9. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard ANSI / EIA 481. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. Matching Circuit and Matching Component Values Used in G3 Sirius Radios (Refer to Sirius Radio G3 Chipset Application Note, Doc. #RX000104-B, Sec. 4.2.3) TDM1 Narrowband SAW Matching Circuit TDM1 Narrowband SAW Matching Values Reference Designator Value C5 C6 L3 L4 C7 C8 10 pF 10 pF 330 nH 560 nH 100 pF 100 pF ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 2 of 7 www.murata.com Matching Circuit and Matching Component Values Used on Filter Demo Board C3 C1 Zinput 1:3 RFM L1 Transformer 16:1 L2 SF2039B Transformer C4 C2 150Ω Zoutput 800Ω SF2039B 72.540 MHz C1 = 10pF C2 = 10pF L1 = 330nH L2 = 390nH C3 = 18pF C4 = 18pF 18 Apr 2005 16:52:40 CH1 S21 LOG 10 dB/ REF -10.5 dB 1 : 0 . 0000 dB 0 . 000 000 MHz SF2039B DEMO PRm CH1 Markers REF=1 3 . 971576 MHz BW : 1 Cor cent 3 2 : 72 . 571132 4 Q: 18 . 273 1_ loss CENTER 72 . 540 000 MHz SPAN ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 3 of 7 MHz 40 . 000 000 : -10 . 623 dB MHz www.murata.com 18 Apr 2005 16:59:10 CH1 S21 LOG 1 dB/ 2 : . 00540 REF -10.85 dB dB 3 . 315 685 MHz SF2039B DEMO CH1 mean Cor 2 . 593 dB s . dev : . 08060 dB p-p : . 28160 dB 1 PRm CH2 : -10 Markers REF=1 S21 DEL 50 ns/ REF 750 ns 2 : -33 . 340 ns 3 . 600 000 MHz CH2 Smo Cor Markers REF=1 mean : 766 . 06 ns s . dev : 11 . 855 ns p-p : 61 . 340 ns 2 1 PRm CENTER 72 . 540 000 MHz SPAN ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 4 of 7 20 . 000 000 MHz www.murata.com 18 Apr 2005 17:02:37 CH1 S11 1 : 41 . 178 1 U FS 0 . 9043 1 . 9840 nH 72 . 540 000 MHz 53 . 342 nH 72 . 540 000 MHz SF2039B DEMO Cor 1 PRm CH2 S22 1 : 37 . 799 1 U FS 24 . 313 1 Cor PRm CENTER 72 . 540 000 MHz SPAN ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 5 of 7 20 . 000 000 MHz www.murata.com SMP-03 Case 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions mm Dimension A B C D E H J K P Recommended PCB Footprint Inches Min Nom Max Min Nom Max 6.80 4.80 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 7.20 5.20 2.00 .73 2.67 1.13 5.13 3.13 1.40 0.268 0.189 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 0.283 0.205 0.079 0.029 0.105 0.044 0.202 0.123 0.055 .47 2.41 0.87 4.87 2.87 1.14 0.019 0.095 0.034 0.192 0.113 0.045 Materials Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Body Al2O3 Ceramic Pb Free Electrical Connections Connection Port 1 Port 2 Terminals Input or Return 10 Return or Input 1 Output or Return 5 Return or Output 6 Ground All others Single Ended Operation Return is ground Differential Operation Return is hot C B E H H J D A P K ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 6 of 7 www.murata.com Tape and Reel Specifications "B" REF. 100 REF. “B “ Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 16.0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 5.5 mm Bo 7.5 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED ©2010-2014 © byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2005 SF2039B (R) 3/27/14 Page 7 of 7 www.murata.com