T13E.pdf
Sep.1,2017
Ceramic Trimmer Capacitors
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
EU RoHS Compliant
F**2&#.0-"3!21',2&'1! 2 *-%!-+.*7
5'2& - @
F - '12&# 30-.# ,'0#!2'4#
|z{{GG -,2&##120'!2'-,-$2&#
1#-$#02 ', 8 0"-313 12 ,!#1',
*#!20'! * ," *#!20-,'! /3'.+#,2@
FFor+-0#"#2 '*1A.*# 1#0#$#r2o-ur5#
. %#A30 2 1..0- !&$-0 -
H&22.BGG555@+30 2 @!-+G#,#3G13..-02G!-+.*' ,!#G0-&1J@
T13E.pdf
Sep.1,2017
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Contents
Product specifications are as of September 2017.
Bluetoothr is a registered trademark
or trademark of Bluetooth SIG, Inc.
in the United States and other countries.
Part Numbering
p2
Selection Guide of Ceramic Trimmer Capacitors
p3
1 TZR1 Series
p4
2 TZY2 Series
p8
3 TZC3 Series
p13
4 TZW4 Series
p18
5 TZB4 Series
p21
Packaging
p26
Recommended Adjustment Tools
p28
Qualified Standards
p29
Please check the MURATA website (http://www.murata.com/)
if you cannot find a part number in this catalog.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
o Part Numbering
Ceramic Trimmer Capacitors
(Part Number)
TZ
Y2
R 200 A C01 R00
1
2
3
4
5
6
7
5Terminal Shape
1Product ID
Product ID
TZ
Trimmer Capacitors
2Series/Terminal
Code
Terminal Shape
A
Top Adjustment: TZR1, TZY2, TZC3, TZW4, TZB4
B
Top Adjustment: TZB4
Please refer to dimensions for terminal details.
Code
Series/Terminal
6Individual Specifications
B4
4mm Size SMD Type
W4
4mm Size SMD Type
Code
Individual Specifications
C3
3mm Size SMD Type
001
TZR1, TZW4 Standard Type
Y2
2mm Size SMD Type
C01
TZY2 Standard Type
R1
1mm Size SMD Type
A01
TZC3 Standard Type
3Temperature Characteristics
Code
Temperature Characteristics
Z
NP0ppm/°C
A10
TZB4 No-cover Film Standard Type
B10
TZB4 with Cover Film Standard Type
7Packaging
R
N750ppm/°C
Code
K
N1000ppm/°C
B00
Bulk
P
N1200ppm/°C
R00
Reel (Taping ø180mm)
R01*
Reel (Taping ø330mm)
Please refer to ratings for tolerance of temperature characteristics.
* TZB4 only.
4Maximum Capacitance
Expressed by three-digit alphanumerics. The unit is pico-farad
(pF). The first and second figures are significant digits, and the
third figure expresses the number of zeros that follow the two
numbers. If there is a decimal point, it is expressed by the capital
letter "R". In this case, all figures are significant digits.
2
Packaging
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T13E.pdf
Sep.1,2017
Selection Guide
Mounting Method?
Surface Mount
Reflow
Height 0.90mm max.
Height 1.7mm max.
TZR1
TZC3
1.5(W) x 1.7(L)
3.2(W) x 4.5(L)
Height 1.25mm max.
Height 3.2mm max.
Flow
High Frequency
Power
TZB4_AB
Height 2.6mm max.
TZW4
4.2(W) x 5.2(L)
TZY2
TZB4_AA
2.5(W) x 3.2(L)
4.0(W) x 4.5(L)
Height 3.2mm max.
4.0(W) x 4.5(L)
(with cover film)
TZB4_BB
4.0(W) x 4.5(L)
(with cover film)
TZB4_BA
4.0(W) x 4.5(L)
All Ceramic Trimmer Capacitor products comply with RoHS and ELV.
3
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1
Sep.1,2017
Ceramic Trimmer Capacitors
TZR1 Series
1.7
Features
0.9 max.
1.5
1. Ultra-small and thin with external dimensions
of 1.5(W)x1.7(L)x0.85(H)mm
(80% less in volume than the current product).
2. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after reflow soldering.
3. Suitable for high frequency circuit due to high
self-resonant frequency (6.2GHz of TZR1Z010 at
1.0pF setting).
(Depth;0.15)
0.45
0.2
0.35
( Tolerance:in±0.1
mm )
Applications
1. Bluetoothr
2. Crystal oscillators
3. Crystal filters
4. Miniature tuner packs (FM Radio, TV)
5. Remote keyless entry systems
Part Number
C min. (max.)
(pF)
C max.
(pF)
TZR1Z010A001
0.55
1.0 +100/-0%
TZR1Z1R5A001
0.7
1.5 +100/-0%
TZR1Z040A001
1.5
4.0 +100/-0%
TZR1R080A001
3.0
8.0 +100/-0% N750±500ppm/°C
Insulation Resistance: 10000M ohm
TC
Construction
Cover
Metal Rotor
Monolithic Stator
4
Rated Voltage
Withstanding Voltage
NP0±300ppm/°C 200min. at 200MHz, Cmax.
25Vdc
55Vdc
NP0±300ppm/°C 200min. at 200MHz, Cmax.
25Vdc
55Vdc
NP0±500ppm/°C
300min. at 1MHz, Cmax.
25Vdc
55Vdc
300min. at 1MHz, Cmax.
25Vdc
55Vdc
Torque: 0.1 to 1.0mNm
Q
Operating Temperature Range: -25 to +85°C
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Characteristics
TZR1Z010
TZR1Z1R5
Z010 (NP0±300 ppm/°C)
Z1R5 (NP0±300 ppm/°C)
8
8
6
6
4
4
2
2
20
–25
85
20
–25
Temp. (°C)
–2
–4
Cap. Change (%)
Cap. Change (%)
85
Temp. (°C)
–2
–4
–6
–8
–10
–12
–6
–8
–10
–12
TZR1Z040
TZR1R080
Z040 (NP0±500 ppm/°C)
R080 (N750±500 ppm/°C)
8
8
6
6
4
4
2
–25
2
20
85
–25
20
85
Temp. (°C)
Temp. (°C)
–2
–2
–4
Cap. Change (%)
–4
Cap. Change (%)
1
–6
–8
–10
–12
–6
–8
–10
–12
Frequency Characteristics
TZR1Z010
TZR1Z1R5
Z010
10000
Z1R5
10000
1000
1000
100
100
0.7pF set
Q
Q
0.55pF set
10
10
1.5pF set
1.0pF set
1
2
8
4
6
Frequency (GHz)
2
4
6
Frequency (GHz)
TZR1R080
Z040
R080
100
Q
100
10
10
1000
1500
Frequency (MHz)
2000
2500
8
10
1000
1000
1000
500
0
TZR1Z040
1000
1
0
10
100
100
Q
0
Capacitance (pF)
0
10
10
1
500
1000
Frequency (MHz)
1500
Capacitance (pF)
1
2000
5
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Land Pattern
1
2.2
0.5
1.2
( Tolerance:in±0.1
mm )
Temperature Profile
oReflow Soldering Profile
2 Soldering profile for Eutectic solder (63Sn/37Pb)
n
1)
(Limit profile: refer to n
T5
T4
T3
T2
Temperature (°C)
Temperature (°C)
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
n
T1
t2
Limit Profile
t3
Standard Profile
t1
T3
T2
t2
T1
t1
time (s)
Standard Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
220°C
time (s)
Standard Profile
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T2)
Standard Profile
30 to 60sec. 245±3°C
2 times
Pre-heating
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T1)
Time (t1)
Temp. (T2)
150°C
60 to 120sec.
183°C
30sec.
230 +5/-0°C
1 time
Limit Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
Heating
Temp. (T4)
230°C
Time (t3)
Peak
Cycle
temperature
of reflow
(T5)
30 to 50sec. 260 +5/-0°C
2 times
oSoldering Iron
Standard Profile
Temperature of soldering iron tip
Soldering time
Soldering iron power output
Cycle of soldering iron
350±10°C
3sec. max.
30W max.
1 time
Notice (Storage and Operating Conditions)
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T13E.pdf
Sep.1,2017
Notice (Soldering and Mounting)
1. Soldering
(1) TZR1 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breaking.
(3) Use a pick-up nozzle of a suitable dimension.
(1.6mm external diameter and 0.8mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1
Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
*Recommended screwdriver for manual adjustment
MURATA: KMDR160
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 0.5 N [Ref: 50gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
7
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Ceramic Trimmer Capacitors
TZY2 Series
3.2±0.2
Features
1.0
0.95
1.25 max.
2.5±0.2
1. Small and thin size with external dimensions
of 2.5(W)x3.2(L)x1.25max.(H)mm.
2. New shape of cover can improve the flux invasion
compared with current products.
3. Improvement of the adhesion between rotor and
stator leads to superior stability.
4. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after reflow soldering.
5. Suitable for high frequency circuit due to high
self-resonant frequency (4.8GHz of TZY2Z010 at
1.0pF setting).
0.5
1.4
2
0.45
( Tolerance:in±0.1
mm )
Applications
1. Crystal oscillators
7. W-LAN
2. Crystal filters
8. Radar detectors
3. Stylus pen
9. Compact radios
4. Hand radios
10. Burglarproof devices
5. Watches
11. Headphone stereos
6. Remote keyless entry systems
Part Number
C min. (max.)
(pF)
C max.
(pF)
TC
Q
Rated Voltage
Withstanding Voltage
TZY2Z010AC01
0.6
1.0 +100/-0%
NP0±300ppm/°C
200min. at 200MHz, Cmax.
25Vdc
55Vdc
TZY2Z2R5AC01
1.0
2.5 +100/-0%
NP0±300ppm/°C
200min. at 200MHz, Cmax.
25Vdc
55Vdc
TZY2Z030AC01
1.5
3.0 +100/-0%
NP0±300ppm/°C
300min. at 1MHz, Cmax.
25Vdc
55Vdc
TZY2Z060AC01
2.5
6.0 +100/-0%
NP0±300ppm/°C
500min. at 1MHz, Cmax.
25Vdc
55Vdc
TZY2Z100AC01
3.0
10.0 +100/-0%
NP0±300ppm/°C
500min. at 1MHz, Cmax.
25Vdc
55Vdc
TZY2R200AC01
4.5
20.0 +100/-0% N750±500ppm/°C
500min. at 1MHz, Cmax.
25Vdc
55Vdc
TZY2R250AC01
5.5
25.0 +100/-0% N750±500ppm/°C
300min. at 1MHz, Cmax.
25Vdc
55Vdc
TZY2K450AC01
8.0
45.0 +100/-0% N1000±500ppm/°C
300min. at 1MHz, Cmax.
25Vdc
55Vdc
Insulation Resistance: 10000M ohm
Torque: 0.7 to 4.9mNm
Construction
Cover
Metal Rotor
Monolithic Stator
8
Operating Temperature Range: -25 to +85°C
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Characteristics
TZY2Z010
TZY2Z2R5
Z010 (NP0±300 ppm/°C)
Z2R5 (NP0±300 ppm/°C)
8
8
6
6
4
4
2
2
20
–25
85
20
–25
Temp. (°C)
–2
–2
2
–4
Cap. Change (%)
Cap. Change (%)
–4
–6
–8
–10
–12
–6
–8
–10
–12
TZY2Z030
TZY2Z060
Z030 (NP0±300 ppm/°C)
Z060 (NP0±300 ppm/°C)
8
8
6
6
4
4
2
2
20
–25
85
20
–25
Temp. (°C)
–2
–4
Cap. Change (%)
Cap. Change (%)
–6
–8
–10
–12
–6
–8
–10
–12
TZY2Z100
TZY2R200
Z100 (NP0±300 ppm/°C)
R200 (N750±500 ppm/°C)
8
8
6
6
4
4
2
2
20
85
–25
20
–2
–4
Cap. Change (%)
Cap. Change (%)
–4
–6
–8
–10
–12
–6
–8
–10
–12
TZY2R250
TZY2K450
R250 (N750±500 ppm/°C)
K450 (N1000±500 ppm/°C)
8
8
6
6
4
4
2
2
20
85
–25
20
–2
–2
–4
–4
–8
–10
–12
Cap. Change (%)
Cap. Change (%)
Temp. (°C)
–6
85
Temp. (°C)
Temp. (°C)
–2
–25
85
Temp. (°C)
–2
–4
–25
85
Temp. (°C)
85
Temp. (°C)
–6
–8
–10
–12
9
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Frequency Characteristics
TZY2Z010
TZY2Z100
Z100
Z010
100
10
2
4
Frequency (GHz)
6
TZY2K450
K450
Q
100
10
10
400
600
Frequency (MHz)
800
1000
Land Pattern
4.0
1.2
2.4
( Tolerance:in±0.1
mm )
Capacitance (pF)
100
10
400
600
Frequency (MHz)
R200
1000
200
200
TZY2R200
1000
1
1
8
800
1000
1000
1000
100
100
Q
0
10
10
1.0pF set
1
100
Q
Q
0.5pF set
10
1
Capacitance (pF)
100
2
1000
1000
10
200
400
Frequency (MHz)
600
800
Capacitance (pF)
1000
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Profile
oReflow Soldering Profile
2 Soldering profile for Eutectic solder (63Sn/37Pb)
n
1)
(Limit profile: refer to n
T5
T4
T3
T2
Temperature (°C)
Temperature (°C)
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
n
T1
t2
Limit Profile
t3
Standard Profile
t1
T3
T2
t2
T1
t1
time (s)
Standard Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
220°C
2
time (s)
Standard Profile
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T2)
Standard Profile
30 to 60sec. 245±3°C
2 times
Pre-heating
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T1)
Time (t1)
Temp. (T2)
150°C
60 to 120sec.
183°C
30sec.
230 +5/-0°C
1 time
Limit Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
Heating
Temp. (T4)
230°C
Time (t3)
Peak
Cycle
temperature
of reflow
(T5)
30 to 50sec. 260 +5/-0°C
2 times
oSoldering Iron
Standard Profile
Temperature of soldering iron tip
Soldering time
Soldering iron power output
Cycle of soldering iron
350±10°C
3sec. max.
30W max.
1 time
Notice (Storage and Operating Conditions)
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
11
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice (Soldering and Mounting)
2
1. Soldering
(1) TZY2 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 120 micro m to 170 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(2.5mm external diameter and 1.2mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR020
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT020
Notice (Other)
Before using trimmer capacitor, please test after
assembly in your particular mass production system.
12
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
T13E.pdf
Sep.1,2017
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Ceramic Trimmer Capacitors
TZC3 Series
0.5±0.05
Depth 0.4±0.05
1. Small size with external dimension of
3.2(W)x4.5(L)x1.6(H)mm.
2. Can be adjusted with conventional adjustment tools
having a thickness of 0.5mm.
3. Designed for automatic placement in surface mount
applications.
4. Heat resistant resin withstands reflow soldering
temperatures.
+
-
2.0
3.2
Features
2.0 dia.
0.8
0.75
1.6
4.5
0.6
0.6
( Tolerance:in±0.1
mm )
3
Applications
1. Compact radios
2. Stylus pen
3. Portable radio equipment
4. Hybrid ICs
5. Remote keyless entry systems
Part Number
C min. (max.)
(pF)
C max.
(pF)
TC
Q
Rated Voltage
Withstanding Voltage
TZC3Z030AA01
1.4
3.0 +50/-0%
NP0±300ppm/°C
300min. at 1MHz, Cmax.
100Vdc
220Vdc
TZC3Z060AA01
2.0
6.0 +50/-0%
NP0±300ppm/°C
500min. at 1MHz, Cmax.
100Vdc
220Vdc
TZC3R100AA01
3.0
10.0 +50/-0%
N750±300ppm/°C
500min. at 1MHz, Cmax.
100Vdc
220Vdc
TZC3P200AA01
5.0
20.0 +50/-0%
N1200±500ppm/°C
300min. at 1MHz, Cmax.
100Vdc
220Vdc
TZC3P300AA01
6.5
30.0 +50/-0%
N1200±500ppm/°C
300min. at 1MHz, Cmax.
100Vdc
220Vdc
Insulation Resistance: 10000M ohm
Torque: 1.5 to 9.8mNm
Operating Temperature Range: -25 to +85°C
Construction
Center Axis
Ceramic
Stator
Rotor Spring Terminal
Stator Electrode Terminal
13
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Characteristics
TZC3Z030
TZC3Z060
Z030 (NP0±300 ppm/°C)
Z060 (NP0±300 ppm/°C)
8
8
6
6
4
4
2
2
20
–25
85
20
–25
3
–2
–2
–4
–4
–6
–8
–10
–12
–6
–8
–10
–12
TZC3R100
TZC3P200
R100 (N750±300 ppm/°C)
P200 (N1200±500 ppm/°C)
8
8
6
6
4
4
2
–25
2
20
85
–25
20
–2
–4
–4
Cap. Change (%)
Cap. Change (%)
–2
–6
–8
–10
–12
TZC3P300
P300 (N1200±500 ppm/°C)
8
6
4
2
20
85
Temp. (°C)
–2
Cap. Change (%)
–4
14
–6
–8
–10
–12
85
Temp. (°C)
Temp. (°C)
–25
85
Temp. (°C)
Cap. Change (%)
Cap. Change (%)
Temp. (°C)
–6
–8
–10
–12
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Frequency Characteristics
TZC3Z030
TZC3Z060
Z030
Z060
500
1000
1500
Frequency (MHz)
10
1
2000
100
500
1000
1500
Frequency (MHz)
TZC3P200
R100
P200
100
Q
100
10
10
400
600
800
Frequency (MHz)
1000
2000
3
1000
1000
100
100
10
10
1
Capacitance (pF)
10
TZC3R100
1000
200
100
Q
100
1000
1
100
10
Capacitance (pF)
1
1000
Capacitance (pF)
Q
10
1000
Q
100
100
Capacitance (pF)
1000
1000
200
400
600
800
Frequency (MHz)
1000
Land Pattern
5.0+0
-0.5
1.0±0.1
3.3±0.1
( Tolerance:in±0.1
mm )
15
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Profile
oReflow Soldering Profile
2 Soldering profile for Eutectic solder (63Sn/37Pb)
n
1)
(Limit profile: refer to n
T5
T4
T3
T2
Temperature (°C)
Temperature (°C)
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
n
T1
t2
Limit Profile
t3
Standard Profile
t1
T3
T2
t2
T1
t1
time (s)
Standard Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
3
220°C
time (s)
Standard Profile
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T2)
Standard Profile
30 to 60sec. 245±3°C
2 times
Pre-heating
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T1)
Time (t1)
Temp. (T2)
150°C
60 to 120sec.
183°C
30sec.
230 +5/-0°C
1 time
Limit Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
Heating
Temp. (T4)
230°C
Time (t3)
Peak
Cycle
temperature
of reflow
(T5)
30 to 50sec. 260 +5/-0°C
2 times
oSoldering Iron
Standard Profile
Temperature of soldering iron tip
Soldering time
Soldering iron power output
Cycle of soldering iron
350±10°C
3sec. max.
30W max.
1 time
Notice (Storage and Operating Conditions)
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
16
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T13E.pdf
Sep.1,2017
Notice (Soldering and Mounting)
1. Soldering
(1) TZC3 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into the
movable part and/or the contact point. The
soldering iron should not come in contact with
the stator of the trimmer capacitor. If such
contact does occur, the trimmer capacitor may
be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
(8) When soldering the TZC3 series, the solder
should not flow into the staking part of the
substrate. If such flow does occur, driver slot
rotation will be damaged.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(2.5mm external diameter and 1.5mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
3
Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
Recommended screwdriver for manual adjustment
Standard type --> MURATA: KMDR080
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
17
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Ceramic Trimmer Capacitors
TZW4 Series
5.2±0.2
1.6
0.4 Depth
2.6 max.
1. To meet high power application due to withstanding
voltage 550Vdc.
2. Extremely high self-resonant frequency.
(More than 3GHz at rated C max.)
3. Typical application: Impedance matching for Cellular
Base Station.
4. High Q value in more than VHF, UHF and Microwave
bands.
(More than 200 in 500MHz, C max.)
5. Available for pick and place machine. Possible
thinner design due to 2.6mm low profile.
6. Non-electrical contact construction
(rotor as middle electrode) provides high reliability.
7. Compact size: 4.2(W)x5.2(L)x2.6max.(H)mm.
0.6
4.2±0.2
Features
2.8±0.2
3.0
2.2
0.3+0.1
-0.2
( Tolerance:in±0.1
mm )
4
Applications
1. Transmitting power amplifier for Cellular base station
2. Transmitting amplifier for PHS base station
3. High frequency electric circuit
4. High power radio transmission
5. Transponder amplifier for cable TV
Part Number
C min. (max.)
(pF)
TZW4Z010A001
0.4
TZW4Z1R5A001
0.4
Insulation Resistance: 10000M ohm
C max.
(pF)
TC
1.0 +50/-0%
Monolithic Stator
18
Rated Voltage
Withstanding Voltage
NP0±150ppm/°C 200min. at 500MHz, Cmax.
250Vdc
550Vdc
1.5 +100/-0% NP0±150ppm/°C 200min. at 500MHz, Cmax.
250Vdc
550Vdc
Torque: 1.5 to 10.0mNm
Construction
Metal Rotor
Q
Cover
Operating Temperature Range: -55 to +125°C
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Characteristics
TZW4Z010
TZW4Z1R5
Z010 (NP0±150 ppm/°C)
Z1R5 (NP0±300 ppm/°C)
8
8
6
6
4
4
2
2
–55
20
125
–55
20
125
Temp. (°C)
–2
–2
–4
–4
Cap. Change (%)
Cap. Change (%)
Temp. (°C)
–6
–8
–10
–12
Frequency Characteristics
–6
–8
–10
–12
Land Pattern
TZW4Z1R5
Z1R5
1000
7.0
4.4
1.5pF set
100
Q
2.5
4
10
1
500
1000
1500
2000
Frequency (MHz)
2500
( Tolerance:in±0.1
mm )
3000
Temperature Profile
oReflow Soldering Profile
2 Soldering profile for Eutectic solder (63Sn/37Pb)
n
1)
(Limit profile: refer to n
T5
T4
T3
T2
Temperature (°C)
Temperature (°C)
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
n
T1
t2
Limit Profile
t3
Standard Profile
t1
T3
T2
t2
T1
t1
time (s)
Standard Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
220°C
time (s)
Standard Profile
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T2)
Standard Profile
30 to 60sec. 245±3°C
2 times
Pre-heating
Heating
Temp. (T1)
Time (t1)
Temp. (T2)
Time (t2)
150°C
60 to 120sec.
183°C
30sec.
Peak
Cycle
temperature
of reflow
(T3)
230 +5/-0°C
1 time
Limit Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
Heating
Temp. (T4)
230°C
Time (t3)
Peak
Cycle
temperature
of reflow
(T5)
30 to 50sec. 260 +5/-0°C
2 times
oSoldering Iron
Standard Profile
Temperature of soldering iron tip
Soldering time
Soldering iron power output
Cycle of soldering iron
350±10°C
3sec. max.
30W max.
1 time
19
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice (Storage and Operating Conditions)
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30
to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(Ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (Ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Notice (Soldering and Mounting)
4
1. Soldering
(1) TZW4 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
the contact failure due to flux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breaking.
(3) Use a pick-up nozzle of a suitable dimension.
(4.0mm external diameter and 1.2mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
-Recommended screwdriver for manual adjustment
VESSEL : No.9000 -1.3x30
(Murata P/N is KMDR130)
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
20
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
T13E.pdf
Sep.1,2017
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Ceramic Trimmer Capacitors
TZB4 Series
1.4±0.1 dia.
3.0±0.2
4.5±0.2
2.7±0.3
1.2±0.1
A Type
( Tolerance:in±0.5
mm )
5.0
1.4±0.1 dia.
4.0±0.2
0.6±0.1 Depth 0.5
2.4±0.1
1. Miniature rectangular shape:
4.0(W)x4.5(L)x3.0(H)mm.
2. Color coded case facilitates identification of
capacitance range.
3. Designed for automatic placement in surface mount
applications.
4. Designed to withstand flux baths and solder baths
(with cover film type).
5. Can be temporarily attached to PCB with adhesives
(Terminal style A and B).
6. Can be reflow and flow (with cover film type)
soldering method.
7. Stable characteristics over a wide frequency range.
(Resonant frequency: 1000MHz min. / 6pF)
2.4±0.1
Features
4.0±0.2
0.6±0.1 Depth 0.5
4.5±0.2
3.0±0.2
Applications
1. Car audio systems
2. Hybrid ICs
3. Remote keyless entry systems
4. Surveillance cameras
5. Burglarproof devices
6. Entry phone
1.2±0.1
B Type
( Tolerance:in±0.5
mm )
7.0
Withstanding
Stator/Case Color
Voltage
Part Number
C min. (max.)
(pF)
C max.
(pF)
TC
TZB4Z030pp10
1.4
3.0 +50/-0%
NP0±200ppm/°C
300min. at 1MHz, Cmax
100Vdc
220Vdc
Brown
TZB4Z060pp10
2.0
6.0 +50/-0%
NP0±200ppm/°C
500min. at 1MHz, Cmax.
100Vdc
220Vdc
Blue
TZB4Z100pp10
3.0
10.0 +50/-0%
NP0±300ppm/°C
500min. at 1MHz, Cmax.
100Vdc
220Vdc
White
TZB4R200pp10
4.5
20.0 +50/-0%
N750±400ppm/°C
500min. at 1MHz, Cmax
100Vdc
220Vdc
Red
TZB4P300pp10
6.5
30.0 +50/-0%
N1200±500ppm/°C 300min. at 1MHz, Cmax
100Vdc
220Vdc
Green
TZB4P400pp10
8.5
40.0 +50/-0%
N1200±500ppm/°C 300min. at 1MHz, Cmax
100Vdc
220Vdc
Yellow
TZB4Z250pp10
4.0
25.0 +100/-0%
NP0±300ppm/°C
300min. at 1MHz, Cmax.
50Vdc
110Vdc
Black+Marking
TZB4R500pp10
7.0
50.0 +100/-0%
N750±300ppm/°C
300min. at 1MHz, Cmax
50Vdc
110Vdc
Black+Marking
Q
Rated Voltage
5
Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85°C
First blank: Terminal Type Second blank: Cover film codes (A: not provided, B: provided)
rex. TZB4Z100A B10: Terminal Type is A, and Cover film is provided.
Construction
Cover Film (Cover film type)
Rotor Spring
Plastic Case
–
Metal Rotor
Ceramic Plate
Stator Terminal
Rotor Terminal
+
21
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Land Pattern/Mounting Holes
A Type
B Type
8.0+0
-0.5
2.4±0.2
4.0±0.2
1.6±0.1
1.6±0.1
7.0+0
-0.5
(in mm)
(in mm)
Temperature Characteristics
TZB4Z030
TZB4Z060
Z030 (NP0±200 ppm/°C)
Z060 (NP0±200 ppm/°C)
8
8
6
6
4
4
2
85
Temp. (°C)
–25
20
–2
–2
–4
–4
Cap. Change (%)
5
2
20
Cap. Change (%)
–25
–6
–8
–10
–12
85
Temp. (°C)
–6
–8
–10
–12
TZB4Z100
TZB4R200
Z100 (NP0±300 ppm/°C)
R200 (N750±400 ppm/°C)
8
8
6
6
4
4
2
2
20
–25
85
–25
20
85
Temp. (°C)
–2
–2
–4
–4
Cap. Change (%)
Cap. Change (%)
Temp. (°C)
–6
–8
–10
–12
–6
–8
–10
–12
TZB4P300
TZB4P400
P300 (N1200±500 ppm/°C)
P400 (N1200±500 ppm/°C)
8
8
6
6
4
4
2
–25
2
20
85
–25
20
–2
–2
–4
–4
–6
–8
–10
–12
85
Temp. (°C)
Cap. Change (%)
Cap. Change (%)
Temp. (°C)
–6
–8
–10
–12
Continued on the following page.
22
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Continued from the preceding page.
Temperature Characteristics
TZB4Z250
TZB4R500
Z250 (NP0±300 ppm/°C)
R500 (N750±300 ppm/°C)
8
8
6
6
4
4
2
2
20
–25
85
–25
20
85
Temp. (°C)
–2
–2
–4
–4
Cap. Change (%)
Cap. Change (%)
Temp. (°C)
–6
–8
–10
–12
–6
–8
–10
–12
Frequency Characteristics
TZB4Z060
TZB4Z100
Z060
Z100
1
100 200
10
1
300 400 500 600 700 800 900 1000
Frequency (MHz)
TZB4R500
R200
R500
1000
Q
10
10
200
300
400
Frequency (MHz)
500
600
5
1000
100
100
Q
100
100
Capacitance (pF)
1000
100
100 200 300 400 500 600 700 800 900 1000
Frequency (MHz)
TZB4R200
1000
1
10
10
Capacitance (pF)
10
10
100
Capacitance (pF)
100
Q
Q
100
Capacitance (pF)
100
1000
1000
1000
1000
10
1
100
200
300
Frequency (MHz)
400
500
23
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Temperature Profile
oFlow Soldering Profile
Temperature (°C)
Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
T3
T2
Standard Profile
t2
Limit Profile
T1
Pre-heating
Standard Profile
t1
Heating
Temp. (T1)
Time (t1)
Temp. (T2)
Time (t2)
Cycle
of reflow
150°C
60 to 120sec.
250°C
5sec. max.
1 time
time (s)
Limit Profile
Pre-heating
F
++#01#2&# -"7',1-*"#0 2&A 4 '* *#$-0!-4#0q*+27.#@
Heating
Temp. (T1)
Time (t1)
Temp. (T3)
Time (t2)
Cycle
of reflow
150°C
60 to 120sec.
265±3°C
5sec. max.
2 times
oReflow Soldering Profile
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
n
2 Soldering profile for Eutectic solder (63Sn/37Pb)
n
1)
(Limit profile: refer to n
Temperature (°C)
Temperature (°C)
T5
T3
T2
T4
T1
t2
Limit Profile
t3
Standard Profile
T3
T2
t2
T1
t1
time (s)
t1
Standard Profile
Pre-heating
Temp. (T1)
5
Time (t1)
150 to 180°C 60 to 120sec.
220°C
time (s)
Standard Profile
Peak
Cycle
temperature
of reflow
Time (t2)
(T3)
Heating
Temp. (T2)
Standard Profile
30 to 60sec. 245±3°C
2 times
Pre-heating
Heating
Temp. (T1)
Time (t1)
Temp. (T2)
Time (t2)
150°C
60 to 120sec.
183°C
30sec.
Peak
Cycle
temperature
of
reflow
(T3)
230 +5/-0°C
1 time
Limit Profile
Pre-heating
Temp. (T1)
Time (t1)
150 to 180°C 60 to 120sec.
Heating
Temp. (T4)
230°C
Time (t3)
Peak
Cycle
temperature
of reflow
(T5)
30 to 50sec. 260 +5/-0°C
2 times
F4 '* *#$-02#0+', *1& .#AA ," @
oSoldering Iron
Standard Profile
Temperature of soldering iron tip
Soldering time
Soldering iron power output
Cycle of soldering iron
350±10°C
3sec. max.
30W max.
1 time
Notice (Storage and Operating Conditions)
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
24
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T13E.pdf
Sep.1,2017
Notice (Soldering and Mounting)
1. Soldering
(1) Can be soldered by reflow soldering method, flow
soldering method, and soldering iron.
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to flux wicking up.
(5) When using soldering iron, the string solder
shall be applied to the lower part of the
terminal only. Do not apply flux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fixed rotor or contact failure
due to flux invasion into the movable part and/or
the contact point. The soldering iron should not
come in contact with the plastic case of the
trimmer capacitor. If such contact does occur,
the trimmer capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) When bending the terminals, do not apply
excessive force to the body of the product to
protect the terminal fixing part from damage.
(4) Use a pick-up nozzle of a suitable dimension.
> Without cover film type
- External dimensions of 4.5x4.0mm and
2.5mm bore diameter.
> With cover film type
- 4.0mm external diameter and 2.0mm bore
diameter.
3. Cleaning [with cover film type]
Isopropyl alcohol and ethyl alcohol are available
material for cleaning. If you use any other type of
solvent, please evaluate performance in your
application. Moreover, please confirm that no
damage has occurred to the trimmer capacitor
after cleaning in your conditions.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
5
Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR010
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT010
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
4. Do not break the cover film before the completion
of PCB mounting, soldering, and cleaning.
5. Do not clean the trimmer capacitor after the cover
film has been broken.
6. To break the cover film, first turn the screwdriver
more than 360°, and set the capacitance value.
(Inserting the screwdriver only will not break the
cover film.)
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
25
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Packaging
Minimum Quantity
Minimum Quantity (pcs.)
Part Number
ø180mm Reel
ø330mm Reel
Bulk
TZR1
3000
-
500
TZY2
2000
-
500
TZC3
1000
-
500
TZW4
500
-
100
TZB4
500
2500
500
Tape Dimensions
TZR1 Series
TZY2 Series
1.5+0.1
-0 dia.
2.0
t
4.0
A
1.05±0.2
0.25
3.5
8.0±0.2
0.25±0.1
8.0±0.3
3.5±0.1
1.75±0.1
1.5+0.1
-0 dia.
3.6±0.2
4.0±0.1
2.0±0.2
4.0±0.1
1.75
2.0±0.1
A-Across
section
A
2.7±0.2
1.8±0.2
4.0
t=TZY2 (TZVY2): 1.6±0.2
( Tolerance:in±0.1
mm )
(in mm)
TZC3 Series
TZW4 Series
8
3.6±0.2
1.75
2.6
5.5
A
5.6
A-Across
section
A
4
12±0.3
4.9±0.2
A
2
0.3
1.75
4
5.5
2
1.5+0.1
-0 dia.
2.0±0.2
( Tolerance:in±0.1
)
mm
A
8
4.6
0.3
12±0.2
1.5+0.1
-0 dia.
A-Across
section
( Tolerance:in±0.1
mm )
TZB4 Series
1.5+0.1
-0 dia.
4 .0
5.5
4.8
7.5
3.55±0.2
0.3±0.1
1.75
2.0
12.0±0.3
8.0
A
A-Across
section
1.8
A
4.3
Direction of feed
( Tolerance:in±0.1
mm )
Continued on the following page.
26
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Packaging
Continued from the preceding page.
Reel Dimensions (180mm diameter)
TZR1/TZY2 Series
TZC3/TZW4/TZB4 Series
21.0±0.8 dia.
2.0±0.5
21.0±0.8 dia.
9.0±1.0
13.0±1.0
13.0±1.0
178±2 dia.
50 min.
2.0±0.5
13.0±0.5 dia.
50 min.
13.0±0.5 dia.
17.0±1.0
178±2 dia.
(in mm)
(in mm)
Reel Dimensions (330mm diameter)
TZB4 Series
2.0±0.5
21.0±0.8 dia.
50 min.
13.0±0.5 dia.
13.5±1.0
17.5±1.0
328±2 dia.
(in mm)
27
T13E.pdf
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Sep.1,2017
Recommended Adjustment Tools
Please use the following recommended screwdrivers.
You can order these drivers using the part numbers below.
Although you can also adjust the capacitance value using commercial products, please use one with the same head size as the
driver listed below.
For Manual Adjustment
Series
MURATA
Model Number
Manufacturer’s
Model Number
Shape
80
1.5
TZR1
KMDR160
MURATA MFG.
KMDR160
Bit shape:
Minus (0.3x0.13)
(in mm)
125
15
TZY2
KMDR020
VESSEL MFG.
NO.9000 -0.9x30
Bit shape:
Minus (0.9x30)
(in mm)
125
15
TZC3
KMDR080
VESSEL MFG.
NO.9000 +1.7x30
Bit shape:
Plus (1.7x30)
(in mm)
122
20
TZB4
KMDR010
50
MURATA MFG.
KMDR010
Bit shape:
Minus (2.2x0.4)
(in mm)
125
15
TZW4
KMDR130
VESSEL MFG.
NO.9000 -1.3x30
Bit shape:
Minus (1.3x30)
(in mm)
For Automatic Adjustment
3.0
5.0
0.2±0.05
MURATA MFG.
Shape
KMBT020
0.4±0.05
KMBT020
Manufacturer’s
Model Number
0.9±0.05
ø2.0
TZY2
MURATA
Model Number
ø2.4
Series
0.6±0.05
10.0
(in mm)
25.0
30
28
KMBT010
MURATA MFG.
KMBT010
Bit shape:
Minus (2.2x0.4)
2.2 dia.
TZB4
(in mm)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T13E.pdf
Sep.1,2017
Qualified Standards
The products listed herein have been produced
by a ISO9001 certified factory.
MURATA FACTORY
Sabae Murata Mfg. Co., Ltd.
* No ODCs (Ozone Depleting Chemicals) are used on
any Murata trimmer capacitors.
29
T13E.pdf
Sep.1,2017
Cat. No. T13E-17
Global Locations
For details please visit www.murata.com
Note
1 Export Control
For customers outside Japan:
No Murata products should be used or
sold, through any channels, for use in the
design, development, production, utilization,
maintenance or operation of, or otherwise
contribution to (1) any weapons (Weapons of
Mass Destruction [nuclear, chemical or biological
weapons or missiles] or conventional weapons)
or (2) goods or systems specially designed or
intended for military end-use or utilization by
military end-users.
For customers in Japan:
For products which are controlled items subject
to the “Foreign Exchange and Foreign Trade Law”
of Japan, the export license specified by the law
is required for export.
2 Please contact our sales representatives or
product engineers before using the products in
this catalog for the applications listed below,
which require especially high reliability for the
prevention of defects which might directly
damage a third party’s life, body or property, or
when one of our products is intended for use
in applications other than those specified in
this catalog.
1
Aircraft equipment
2
Aerospace equipment
3
Undersea equipment
4
Power plant equipment
5
Medical equipment
6
Transportation equipment (vehicles, trains,
ships, etc.)
7
Traffic signal equipment
8
Disaster prevention / crime prevention
equipment
9
Data-processing equipment
10
Application of similar complexity and/or
reliability requirements to the applications
listed above
Murata Manufacturing Co., Ltd.
www.murata.com
3 Product specifications in this catalog are as of
September 2017. They are subject to change or
our products in it may be discontinued without
advance notice. Please check with our sales
representatives or product engineers before
ordering. If there are any questions, please contact
our sales representatives or product engineers.
4 Please read rating and CAUTION (for storage,
operating, rating, soldering, mounting and
handling) in this catalog to prevent smoking
and/or burning, etc.
5 This catalog has only typical specifications.
Therefore, please approve our product
specifications or transact the approval sheet
for product specifications before ordering.
6 Please note that unless otherwise specified, we
shall assume no responsibility whatsoever for any
conflict or dispute that may occur in connection
with the effect of our and/or a third party’s
intellectual property rights and other related
rights in consideration of your use of our products
and/or information described or contained in our
catalogs. In this connection, no representation
shall be made to the effect that any third parties
are authorized to use the rights mentioned above
under licenses without our consent.
7 No ozone depleting substances (ODS) under the
Montreal Protocol are used in our manufacturing
process.
工商网监
湘ICP备2023018690号
