VFS9VD31B223Q91J

Spec No. JEWE243B-0005H-01 Reference Only P1/7 EMIGUARD (Three-Terminal Varistor-Capacitor) VFS9V Series Reference Specification 1.Scope This reference specification applies to Disc-Type EMIFIL (Three-terminal Varistor-Capacitor). 2.Part Numbering (Ex.) VF S 9 V D3 1B 223 Q93 J ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ①Product ID (EMIGUARD Lead Type） ②Structure ③Style ④Features ⑤Temperature Characteristics ⑥Rated Voltage ⑦Capacitance ⑧Lead Type Q55 : Bulk / Q9 : Taping See item 9. ⑨Packaging Code B : Bulk / J : φ 320mm reel (Bulk) Customer Part Number (Taping) Customer Part Number Part Number VFS9VD31B223Q55B Unit Mass (Typical value) 1.2g Part Number VFS9VD31B223Q91J VFS9VD31B223Q92J VFS9VD31B223Q93J Unit Mass (Typical value) 1.1g 3.Rating D3 (± Temperature Characteistics 20 30 %) Capacitance value (-25 to+85°C) 22000 pF ± Capacitance Tolerance 50 20 % Rated Voltage 12 V(DC) Varistor Voltage(V1mA) 22V(DC) ± 20% Voltage Ratio 1.25 max.(V10mA / V1mA) Insulation Resistance 1MΩ min. Rated Current Bulk : 7A (DC) Taping : 6A (DC) Operating Temperature -40 to +100°C Storage Temperature -40 to +100°C Equivalent Circuit 1 3 （3） （1） 2 1g 4.Style and Dimensions See item 9. 5.Marking Temperature Characteristics Capacitance Capacitance Tolerance Rated Voltage Varistor Voltage Trade Mark : : : : : : D (Temperature Characteristics Number : D3) Marked three digits system. 50 Marked letter code. S (± 20%) Marked voltage value. (12V → 12) Marked voltage value. (22V → 22) Marked as MURATA MFG CO.,LTD Spec No. JEWE243B-0005H-01 Reference Only P2/7 6.Testing Condition Temperature : Ordinary Temperature 15 to 35 °C Humidity : Ordinary Humidity 25 to 85%RH Temperature : 20±2°C Humidity : 60 to 70% Atmospheric Pressure : 86 to 106 kPa 7.Electrical Performance No. 7.1 7.2. 7.3 7.4 7.5 Item Specification Style and Meet item 9. Dimension Marking Marking is able to be read easily. Capacitance and Meet item 3. Tolerance Insulation Resistance(I.R.) Varistor Voltage Test Method Visual Inspection and measured with Slide Calipers. Visual Inspection. Frequency : 1±0.1kHz Test Voltage : 0.1 V(rms) Test Voltage : 10 V Time : 5±1 minute through a suitable resistor 10kΩ. Products Measuring Current : 1 mA A ＋ V E － 7.6 Voltage Ratio 7.7 Characteristic (TC) Measuring Current : 1 mA , 10mA Measureing circuit : See 7.5 Calculate expression : V 10 / V1 V 10 : Varistor Voltage at 10mA V1 : Varistor Voltage at 1 mA Capacitance shall be measured at each step specified in Table 1 after reaching the thermal equilibrium. The capacitance change against the capacitance at step 3 shall be calculated. Table1 Step Temp. (°C) 7.8 7.9 Temperature Cycle Humidity Meet Table 2. Table 2 Appearance Capacitance Change Insulation Resistance Varistor Voltage Change Voltage Ratio 7.10 Heat Life 7.11 Overload 7.12 Surge(1) Meet Table 3. Table 3 Appearance Capacitance Change Insulation Resistance Varistor Voltage Change Voltage Ratio No damaged. within ± 15% 500kΩ min. within ± 15% 1.25 max. No damaged. within ± 15% 500kΩ min. within ± 15% 1.30max. 1 2 3 4 5 +20±2 -25±2 +20±2 +85±2 +20±2 1 cycle Step 1 -40°C (+0°C,-3°C) / 30 min. Step 2 Ordinary Temp. / within 5 min. Step 3 +125°C (+3°C,-0°C) / 30 min. Step 4 Ordinary Temp. / within 5 min. Total 10 cycles Then measured after exposure in the room condition 4 to 24 hours. Temperature : 40 ± 2°C Humidity : 90 to 95 %(RH) Time : 500 hours(+12-0 hours) Then measured after exposure in the room condition 4 to 24hours. Temperature : 85 ± 3°C Time : 1000 hours(+24-0 hours) Applying Voltage : varistor voltage(V1mA) Then measured after exposure in the room condition 4 to 24hours. Applying Voltage : 1.4 times varistor voltage(V1mA) Time : 5 minutes Circuit : See 7.5 Applying Voltage(E) : 400V(DC) Dump Capacitor(C) : 0.47 µF Interval of Application : ON / OFF 1 second The number of applied times : 105 times Then measured after exposure in the room condition 1 to 2 hours. + E 400V MURATA MFG CO.,LTD C for for for for Spec No. JEWE243B-0005H-01 No. Item 7.13 Surge(2) Reference Only Specification Meet Table 3. Test Method Voltage shall be charged to dump capacitor,and then discharged through the specimen.(JASO A-1) The number of applied times : 1 time Decay time constant : 200 ms Decay time constant means the time that the voltage decay to 36.8% of the maximum voltage. E 70V 7.14 ESD test 7.15 Solderability 7.16 Resistance to Soldering Heat 7.17 Vibration 7.18 Terminal Strength P3/7 ＋ C － 110mF 0.8Ω 2Ω Energy storage capacitance : 150 pF Discharge resistance : 330ΩTest Voltage : 25kV(DC) Discharge method : Contact discharge The Number of times : 10 times of each polarity Then measured after exposure in the room condition for 4 to 24hours. Along the circumference of Flux : Ethanol solution of rosin,25(wt)% terminal shall be covered with new (dipped for 5 to 10 seconds) solder at least 75%. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 245±5℃ Immersion Time : 2 ± 0.5 seconds Immersion Depth : 1 mm from the bottom of the body. Meet Table 2. Flux : Ethanol solution of rosin,25(wt)% (dipped for 5 to 10 seconds) Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 270 ± 5 °C Immersion Time : 10± 1 seconds Immersion Depth : 1.6 ± 0.8 mm from the bottom of the body. Then measured after exposure in the room condition for 4 to 24hours. Meet Table 2. It shall be solderd on the substrate. Range of Vibration Frequency : 10 to 2000 to 10(Hz) / 20 minutes Amplitude : 1.5mm or acceleration (about 196m/s2) Direction of Vibration : 3 perpendicular directions Duration of Vibration : 6 hours (2 hours in each directions) (Pull Test) Applying Force : 10N It shall be no damaged. Time : 5±1 seconds. (Bend Test) The load (5N) shall be hung at the tip of the leads. It shall be no damaged. The body of the EMIFIL shall be bent 90° and returned to its original position. And the body shall be bend 90° in the opposite direction, and returned to its original position. Load 5N 8.Mounting Hole Taping φ 0.8 -3 φ 1.0 -3 2.5±0.2 Bulk (in mm) 2.5±0.2 2.5±0.2 2.5±0.2 MURATA MFG CO.,LTD 2.5±0.2 Reference Only ∗2 25.0 min. F1 2.5±0.5 φ 0.65 5.0±0.5 F1=2.5±0.5 1 (3) 2 10.5 max. D 223S 12－22 F1 P4/7 7.5 max. 12.0 max. 1.0 max. 1.5 max. ∗1 Spec No. JEWE243B-0005H-01 9.Style and Dimension 9.1 Bulk Type (in mm) 3 (1) ∗1 Coating extending on leads does not exceed the tangent line. Exposed electrode,if any,is covered by solder,etc. ∗2 There should not be the exposure of the ferrite bead if a hole is on top of ferrite bead. 7.5 max. 9.2 Taping Type D Δs D0 123 ∗ 1(A) d l W0 ∗2 (3) (1) t1 t2 P0 Δ h2 11.0 max. H F1 ∗2 ∗1 F1 W2 ∗3 F L W1 P1 W Δ h1 H P 1.5 max. P2 ∗1. Coating extending on leads does not exceed the start of bend.(Point A). Exposed electrodes are covered with solder. ∗2. H : to be measured from the forming point A . ∗3. The deviation between two ferrite beads shall be less than 1.2mm. Code Description Dimensions P Pitch of Component P0 P1 Pitch of Sprocket Hole Length from Hole Center to Lead Length from Hole Center to Component Center Width of Body Deviation along tape, Left or Right Carrier Tape Width Position of Sprocket Hole Protrusion Length Diameter of Sprocket Hole Lead Diameter Total Tape Thickness Total Thickness,Tape and Lead Wire Deviation across Tape,front Deviation across Tape,rear Portion to Cut in Case of Defect Hold Down Tape Width Hold Down Tape Position P2 D ΔS W W1 l D0 d t1 t2 Δh1 Δh2 L W0 W2 H Lead length between sprocket hole and forming position F F1 Lead Spacing 12.7 12.7±0.2 3.85±0.7 6.35±1.3 Q91 Q92 Q93 12.0 max. 0±1.0 18.0±0.5 9.0 +0 / -0.5 +0.5 ∼ -1.0 φ 4.0±0.1 φ 0.6 0.7±0.2 1.5 max. 1.0 max. 1.0 max. 11.0 +0 / -1.0 12.0±0.5 1.5±1.5 20.0±1.0 16.5±1.0 18.5±1.0 5.0 +0.8 / -0.2 2.5 +0.4 / -0.2 MURATA MFG CO.,LTD Remark Product Inclination ΔS Determines Crossing Shift In Tape In Direction of Feed Tape Widthwise Shift Includes Thickness of Bonding Tape Reference Only Spec No. JEWE243B-0005H-01 P5/7 (in mm) 10.Taping 10.1 (1) A maximum of 0.3% of the components quantity per reel or Flat pack may be missing without consecutive missing components. 10.2 The adhesive power of the tape shall have over 2.94N at the following condition. F 2.94 N Hold down tape Carrier tape 10.3 Splicing method of tape 1. Carrier tape Carrier tape shall be spliced by cellophane tape. Overall thickness shall be less than 1.05 mm. Direction of feed Overall thickness Hold down tape Carrier tape 30 to 50 2. Hold down tape Cellophane tape (in mm) Hold down tape shall be spliced with overlapping. Overall thickness shall be less than 1.05 mm. Direction of feed 20 to 30 Hold down tape Hold down tape Carrier tape Overall thickness (in mm) 3. Both carrier tape and hold down tape Both tapes shall be cut zigzag and spliced with splicing tape. 11. Packing 11.1 Packing quantity Terminal Configuration A Unit Quantity Packing Form Bulk 200 pcs. In a plastic bag Taping 800 pcs. In a reel ∗ A quantity in a container is depending on a quantity of an order. 11.2 Packing Form (1)Bulk 1.Products are packed into a plastic bag. 2.The plastic bags are put into a container (corrugated cardboard box) depending on a quantity of an order. the plastic bag with products a plastic bag a container  (2)Taping container label 325max. Label Kraft paper 76±2 30 ±1 1 .Taped products are loaded in a reel made of corrugated cardboard. 2. The dimensions of the reel and the products orientation are as shown in below. 3. The products loaded in the reel are put into a container (corrugated cardboard box) depending on a quantity of an order. 4. Not less than 3 consecutive of component shall be missing on both edge of tape. Murata Products Murata Products Hold down tape 53max. MURATA MFG CO.,LTD (In mm) Spec No. JEWE243B-0005H-01 12.Marking on package 12.1 Unit Package Reference Only P6/7 Bulk : Marked on a plastic bag. Taping : Marked on a label stuck on a reel. Marking on a unit package consists of : Customer part number, MURATA part number, Inspection number(∗1), RoHS marking (∗2), Quantity, etc ∗1) « Expression of Inspection No. » □□ OOOO ××× (1) Factory Code (2) Date (3) Serial No. (1) (2) (3) First digit : Year / Last digit of year Second digit : Month / Jan. to Sep. → 1 to 9, Oct. to Dec. → O,N,D Third, Fourth digit : Day ∗2) « Expression of RoHS marking » ROHS – Y (△) (1) RoHS regulation conformity parts. (2) MURATA classification number (1) (2) 12.2 Container Marking on the label sticked on a container consists of : Customer name Purchasing Order Number, Customer Part Number, MURATA part number, RoHS marking (∗2), Quantity, etc 13. ! Caution 13.1 Mounting holes Mounting holes should be designed as specified in this specifications. (See item 8.) Or different design from this specifications may cause cracks in ceramics which may lead to smoking / firing. 13.2 Mounting for P.C.B. (Applied only to bulk type.) Form of mounting hole is a triangle.(See item 8.) Product should be inserted and soldered to each holes correct way as Fig.1.(The center terminal and the other terminals become parallel when seeing a product from the side.) Smorking and firing maybe caused by wrong way like a Fig.2. (The center terminal and the other terminals cross when seeing a product from the side.) Marking Side Center Terminal (GroundTerminal) Fig.1 Right Way Fig.2 Wrong Way 13.3 Terminal Varistor-Capacitor Products should not be applied for the absorption of surge which have large energy (ex. Included lighting surge,switching surges) because it is designed for the absorption of electrostatic surges. 13.4. Caution for the product angle adjust work Take care not to apply any mechanical stress to product body at the lead terminal bending process for product angle adjustment after insertion. 13.5 Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1) Aircraft equipment (7) Traffic signal equipment (2) Aerospace equipment (8) Disaster prevention / crime prevention equipment (3) Undersea equipment (9) Data-processing equipment (4) Power plant control equipment (10) Applications of similar complexity and /or reliability requirements to the applications listed in the above (5) Medical equipment (6) Transportation equipment (vehicles, trains, ships, etc.) MURATA MFG CO.,LTD Spec No. JEWE243B-0005H-01 14. Notice 14.1 Soldering Reference Only P7/7 (1) Use rosin-based flux. Do not use strong acidic flux with halide content exceeding 0.2(wt)% (chlorine conversion value). Use Sn-3.0Ag-0.5Cu solder T e m p e ra tu re (° C ) (2) Standard flow soldering profile. 300 Pre- heating(in air) Soldering Gradual Cooling (in air) Solder temp. 250 Solder temperature 250～260 °C 200 150 100 Soldering time 4～6s 50 1 minutes min. Soldering time (3) Resistance to soldering iron goes in the following condition that tip temperature is 350 °C max. and soldering time is 5 s max. (4) Products and the leads should not be subject to any mechanical stress during soldering process. (and also while subject to the equivalent high temperature.) 14.2 Cleaning Products shall be cleaned on following conditions. (1) Cleaning Temperature: 60℃ max.(40℃ max. for Isopropyl alcohol). (2) Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon at the mounted products and P.C.B. Power : 20W / l max. Frequency : 28kHz ∼ 40kHz Time : 5 minutes max. (3) Cleaning agent 1. alcohol cleaning agents. ・Isopropyl alcohol (IPA) 2. Aqueous cleaning agent ・Pine Alpha ST-100S (4) Ensure that residual flux and residual cleaning agent is completely removed. Products should be thoroughly dried after aqueous agent has been removed with de-ionized water. (5) For other cleaning methods, please contact Murata engineering. 14.3 Operating Environment (1) Do not use products in corrosive gases such as chlorine gas, acid or sulfide gas. (2) Do not use products in the environment where water, oil or organic solvents may adhere to products. (3) Do not adhere any resin to products, coat nor mold products with any resin (including adhesive)to prevent mechanical and chemical stress on products. 14.4 Storage and handling requirements (1) Storage period Use the products within 12 months after delivered. Solderability should be checked if this period is exceeded. (2) Storage environment condition To prevent products quality deterioration, storage conditions should be controlled as follows ; 1. Temperature : -10 to 40 degrees centigrade 2. Humidity : 15 to 85% relative humidity 3. Products should be stored without sudden changes in temperature and humidity. Don't keep products in corrosive gases such as sulfur,chlorine gas or acid, or it may cause oxidization of lead terminals resulting in poor solderability. 4. Products should be stored on the palette for the prevention of the influencefrom humidity, dust and so on. 5. Products should be stored in the warehouse without heat shock, vibration,direct sunlight and so on. (3) Handling Conditions Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 15. ! Note (1)Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2)You are requested not to use our product deviating from the reference specifications. (3)The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG CO.,LTD