IRA-E420

!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors Murata Manufacturing Co., Ltd. Cat.No.S21E-4 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 CONTENTS Part Numbering 1 2 3 4 HIC® in this catalog are the trademarks of Murata Manufacturing Co., Ltd. 1 2 3 4 Dual Type Pyroelectric Infrared Sensor IRA-E700 Series Quad Type Pyroelectric Infrared Sensor IRA-E900 Series Quad Type Pyroelectric Infrared Sensor IRA-E940ST1 Series Temperature Compensation Single Type Pyroelectric Infrared Sensor IRA-E420 Series 5 7 10 13 Pyroelectric Infrared Sensor IRA Series Characteristics Data Fresnel Lens Notice Recycled Paper !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 o Part Numbering Pyroelectric Infrared Sensor (Part Number) IR q qProduct ID wType eCharacteristics rIndividual Specification Code * Part Number shows only an example which might be different from actual part number. * "eCharacteristics" and "rIndividual Specification Code" might have different digit number from actual Part Number. Aw E710ST e 1 r 1 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 1 Pyroelectric Infrared Sensors Dual Type Pyroelectric Infrared Sensor IRA-E700 Series Pyroelectric infrared sensors, IRA series, exhibit high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique expertise developed over many years. IRA-E700 series realizes cost benefits and higher performance with a new infrared sensor element of improved material parameters and fabrication. IRA-E700 series is available in two types. IRA-E710ST0 has enhanced immunity to RFI (Radio Frequency Interference). ! Features 1. High sensitivity and excellent S/N ratio 2. High stability to temperature changes 3. Slight movement can be detectable. 4. High immunity to external noise (Vibration, RFI etc.) 5. Custom design is available. 6. Higher in cost-performance ! Dimensions & Circuit Diagrams 4.7±0.1 3.7±0.1 9.2 45° φ0.45 ±0.05 5. 0± 45° ! Applications 1. Security 2. Lighting appliances 3. Household or other appliances 11.0±2 ∗Specified on the bottom of stem ∗ !Rating (25˚C) Part Number Responsivity (500K, 1Hz, 1Hz) Field of View Optical Filter Electrode Supply Voltage Operating Temperature Storage Temperature IRA-E700ST0 IRA-E710ST0 d s g 4.3mVp-p (Typ.) θ1=θ2=45° 5µm long-pass (2.0Z1.0mm)Z2 2 to 15V -40 to 70D -40 to 85D 3.6 4.7 05 0. General Tolerance : ±0.2 (in mm) Pyroelectric element 2.0 1.0 1.0 1.0 (in mm) IRA-E700ST0 RG d s g IRA-E710ST0 d s RG g 2 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors Quad Type Pyroelectric Infrared Sensor IRA-E900 Series 2 Pyroelectric infrared sensors, IRA series, exhibit high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique expertise developed over many years. IRA-E900 series realizes cost benefits and higher performance with a new infrared sensor element of improved material parameters and fabrication. IRA-E900 series is available in two types. IRA-E910ST1 has enhanced immunity to RFI (Radio Frequency Interference). ! Features 1. High sensitivity and excellent S/N ratio 2. High stability to temperature changes 3. Slight movement can be detectable. 4. Non directional sensing with wide F.O.V. 5. High immunity to external noise (Vibration, RFI etc.) 6. Custom design is available. 7. Higher in cost-performance ! Dimensions & Circuit Diagrams 4.7±0.1 41° 9.2 41° φ0.45 ±0.05 11.0±2 3.6 4.7 ! Applications 1. Security 2. Lighting appliances 3. Household or other appliances ∗Specified on the bottom of stem 5.08±0.05∗ ! Rating (25˚C) Part Number Responsivity (500K, 1Hz, 1Hz) Field of View Optical Filter Electrode Supply Voltage Operating Temperature Storage Temperature IRA-E900ST1 IRA-E910ST1 d s g General Tolerance : ±0.2 (in mm) 3.3mVp-p (Typ.) θ1=θ2=41° 5µm long-pass (1.1Z1.1mm)Z4 3 to 15V -25 to 55D -40 to 85D Pyroelectric element 1.1 1.0 1.1 1.1 1.0 1.1 (in mm) d IRA-E900ST1 W Y Y W W Y Y W Y W W Y Y W W Y s RG g IRA-E910ST1 d W Y Y W W Y Y W Y W W Y Y W W Y s RG g 3 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors Quad Type Pyroelectric Infrared Sensor IRA-E940ST1 Series 3 Pyroelectric infrared sensors, IRA series, exhibit high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique expertise developed over many years. IRA-E940ST1 realizes cost benefits and higher performance with a new infrared sensor element of improved material parameters and fabrication. IRA-E940ST1 which has quad elements and 2 outputs will detect the human body more correctly with OR/AND logic circuit. ! Features 1. High sensitivity and excellent S/N ratio 2. High stability to temperature changes 3. High immunity to external noise (Vibration, RFI etc.) 4. Higher in cost-performance 5. Custom design is available. ! Dimensions & Circuit Diagrams 4.7±0.1 50° 9.2 55° φ0.45 ±0.05 11.0±2 3.6 4.7 ! Applications 1. Security 2. Lighting appliances 3. Household or other appliances ! Rating (25˚C) Part Number Responsivity (500K, 1Hz, 1Hz) Field of View Optical Filter Electrode Supply Voltage Operating Temperature Storage Temperature IRA-E940ST1 3.3mVp-p (Typ.) θ1=55°, θ2=50° 5µm long-pass (1.35Z1.0mm)Z4 2 to 15V -25 to 55D -40 to 85D s1 d g s2 ∗Specified on the bottom of stem ∗ 5.08±0.05 General Tolerance : ±0.2 (in mm) Pyroelectric element (Y) W (Y) W Y (W) Y (W) 1.35 0.3 1.35 1.0 0.8 1.0 (in mm) d RG RG s2 s1 g 4 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors Temperature Compensation Single Type Pyroelectric Infrared Sensor IRA-E420 Series Single type pyroelectric infrared sensors IRA-E420 series have a temperature compensation element. They are suitable for flame detection and gas detection. ! Features 1. High stability against abrupt ambient temperature changes 2. High immunity to external noise (Vibration, RFI etc.) 3. Custom design is available with varying optical filter. ! Applications Part Number IRA-E420S1 IRA-E420QW1 IRA-E420SW1 Optical Filter Silicon 4.3µm band-pass 4.45µm band-pass Applications 1-15µm infrared detection Flame detection Flame detection 4 ! Dimensions & Circuit Diagrams (IRA-E420S1, IRA-E420QW1) 2.4±0.1 17° 9.2 (IRA-E420SW1) 1.5 max. 3.0±0.1 17° 50° 3.6 4.9 4.5 11±2 5.08±0.05 ∗Specified on the bottom of stem d General Tolerance : ±0.2 (in mm) s g General Tolerance : ±0.2 (in mm) ∗ 11.0±2 ø0.45 ±0.05 ø0.45±0.05 5.08±0.05∗ 3.6 9.2 d s g ∗Specified on the bottom of stem Pyroelectric element 1.6 (in mm) Pyroelectric element 1.8 (in mm) d s g RG 5 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 ! Rating (25˚C) Part Number Responsivity (500K, 1Hz, 1Hz) Field of View Optical Filter Electrode Supply Voltage Operating Temperature Storage Temperature * 700K, 5Hz, 1Hz IRA-E420S1 3.4mVp-p (Typ.) θ1=θ2=17° Silicon ø1.6mm IRA-E420QW1 1.3mVp-p (Typ.)* 4.3µm band-pass IRA-E420SW1 0.45mVp-p (Typ.) θ1=θ2=50° 4.45µm band-pass ø1.8mm 3 to 15V -25 to 70D -25 to 55D -30 to 100D -25 to 70D 4 6 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensor IRA Series Characteristics Data ! Spectral Response of Window Materials Wave length (µm) 2.5 100 3.0 4.0 5.0 6.0 7.0 8.0 10.0 12.0 5µm Long-Pass Filter 80 4.3µm Band-Pass Filter Transmittance (%) 60 40 Silicon Filter 20 7µm Long-Pass Filter 0 4000 3500 3000 2500 2000 1800 Wave number (cm-1) 1600 1400 1200 1000 800 4 ! Frequency Characteristics 10 Relative Responsivity (RV) 1 1.0 10 Chopping Frequency (Hz) 7 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensor IRA Series Characteristics Data ! Test Method of Sensitivity Lock-in Amplifier (1Hz) 140mm W5V Black Body 500K*1 d s 47kΩ W 22µF g Mechanical Chopper 1Hz*1 Infrared Sensor Oscilloscope Black Body *1 Mechanical Chopper 5Hz 2.5Hz 1Hz IRA-E420QW1 IRA-E420SW1 IRA-E700/E900 Series 700K 400K 500K 4 ! Typical Application Circuit (Human Detection) 3 Terminal Regulater 78L05 260k B222K 220k 10M NJM 2903M 100k 4 2 1S184 R 6 7 W W10µ 9Y15 8 100k 100k 2SD596 B102K D S g 100k 1 B102K 120k 120k W 4.7µ LM358 B102K 10M B222K 1S184 330k 3.3µ 16V 100k W 3 µPD5555G Photo Coupler W 100µ 16V W 100µ 16V 16V 100k LM358 330k B102K 220k 10µ 16V 16V C Relay 1k 5 B103K GND W 1 TH=1.1ZC (µF) Z R (MΩ) second 8 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensor IRA Series Characteristics Data ! Reliability Test IRA-E700 series, IRA-E900 series Item High Temperature Low Temperature Humidity Heat Cycle 100D for 500 hrs. Y40D for 500 hrs. 60D, 95% RH for 500 hrs. 20 times of following cycle. Y25D, 30 min.eRoom temp., 30 min.h gRoom temp., 30 min.f55D, 30 min. Apply vibration of amplitude of 1.5mm with 10 to 55Hz band to each of 3 Vibration Shock Soldering Heat Hermetic Sealing perpendicular directions for 60 min. Apply shock of 100G sinewave by standard shock tester to each of 3 perpendicular directions. Immerse up to 3.0mm from can case in solder bath of 260T5D for 10T1 s. Conform to MIL-STD-202F chapter 112D, condition D. Immerse in fluorocarbon bath (FC-40) of 125T5D for 20 s. Test Conditions Criteria After test completion, leave for three hours in normal humidity temperature conditions, and then measure. 1. External appearance: No significant damage 2. Sensitivity: Tolerance within 20% deviation from original value 3. Noise: Maximum tolerance W100mV of original value No generation of bubbles IRA-E420 series Item High Temperature Low Temperature Humidity Heat Cycle 100D for 500 hrs. Y30D for 500 hrs. 60D, 95% RH for 500 hrs. 20 times of following cycle. Y25D, 30 min.eRoom temp., 30 min.h gRoom temp., 30 min.f55D, 30 min. Apply vibration of amplitude of 1.5mm with 10 to 55Hz band to each of 3 Vibration Shock Soldering Heat Hermetic Sealing perpendicular directions for 60 min. Apply shock of 100G sinewave by standard shock tester to each of 3 perpendicular directions. Immerse up to 3.0mm from can case in solder bath of 260T5˚C for 10T1 s. Conform to MIL-STD-202F chapter 112D, condition D. Immerse in fluorocarbon bath (FC-40) of 125T5D for 20 s. Test Conditions Criteria After test completion, leave for three hours in normal humidity temperature conditions, and then measure. 1. External appearance: No significant damage 2. Sensitivity: Tolerance within 20% deviation from original value 3. Noise: Maximum tolerance W100mV of original value No generation of bubbles 4 9 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors/Fresnel Lens PPGI0601 B' C' 16.3 A m 3.0 C C 2.0 B D B D A A D' B' D' B' C' C' 3.0 1.0 2.0 3.0 4.0 5.0 m m 4.0 D, D' 3.0 22.5° Vertical Area 2.0 E' 1.0 30° 1.0 E, E' 0 1.0 2.0 3.0 4.0 5.0 m C C' B B' A D D' C B E E' 1.0 16.0 11.64 R Horizontal Area 0 E 6.4 5.0 3.64 2.0 Cross-Sectional View 3.60 2.24 (in mm) 4 φ20.0 φ21.0 PPGI0902 Sensor Horizontal Area 7.7m Vertical Area 21.5 9m 2m 44.5 10 8 29.6 Sensor R 10m 1m 1.6m 3.5m 10m 9m 51.5 56.5 7.7m 12° (in mm) 29.6R Lens plane 0.7max. 10 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors/Fresnel Lens PPGI0626 φ23T0.2 12.9SR φ21.4 φ19.4 A B C 12 .1 2 3.6 6 3 SR Pyroelectric element 3 (in mm) 16.5 Y 2.5m Detection area on the floor B : 60° pitch C : 30° pitch Y C1 C12 B1 B6 X C10 B5 C9 B4 B3 C5 B2 C4 Z C2 0.5m 4 3 (m) 2.2m C3 0.8m B 1 A B C A : 0° B : 21.8° C : 48° Y 3 6m 2 1 0 2 C11 C8 C7 C6 IML-0635 Tab ø9.0 8.65 4.5 ø8.2 Step 9.15 3.4 4.35 Housing (4.35) 35º 2m 13º (4.5) 13º 5m 10.8m C 3.0 1.15 5.7 R4.8 1.15 4.0 Pyro-Element Figure A 0m 0m 5.2 5.7 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens). Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent misdetection. Unless otherwise unexpected infrared ray comes though the hatching area. (in mm) General tolerance : ±0.2 35º 2m Vertical 5.5 6m Horizontal *Assembled with Murata sensor IRA-700 series 1.8m 11 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Pyroelectric Infrared Sensors/Fresnel Lens IML-0636 0.5 Tab 0.5 ø9.0 8.65 ø8.2 Step 4.5 13º (4.5) 13º 4m 3m 5m 19.3º 6.6m ø10.4 Focal point (Pyro-Element) Figure A 0m 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens). Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area. (in mm) General tolerance : ±0.2 0m 3m 4m Horizontal Vertical *Assembled with Murata sensor IRA-700 series 4 IML-0637 0.5 Tab 0.5 ø9.0 8.65 ø8.2 Step 4.5 0.5 3.4 13º (4.5) 13º 2m 5m 2m 5m Housing (4.35) 9.15 2.7m 19.3º 19.3º 5.54m Vertical 3m 3m 42° 0m 42° 3m Vertical Vertical Horizontal Pyroelectric Element 1.8m 0.5 3.4 Housing (4.35) 9.15 ø10.4 Focal point (Pyro-Element) Figure A 0m 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens). Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area. (in mm) General tolerance : ±0.2 19.3º 0m 2m Horizontal 2m *Assembled with Murata sensor IRA-700 series IML-0638 6.11m Tab ø9.0 8.65 4.5 ø8.2 Step 3.4 4.35 Housing (4.35) 9.15 13º (4.5) 13º 4.91m 3.0 1.15 5.7 R4.8 1.15 4.0 Pyro-Element Figure A 3m On the Floor 0m 3m 5.2 5.7 1) Insert a sensor into Fresnel lens like each tab is overlapped. (In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens). Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.) 2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens. 3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent misdetection. Unless otherwise unexpected infrared ray comes though the hatching area. (in mm) General tolerance : ±0.2 5.5 45.5° Horizontal 45.5° Assembled with Murata sensor IRA-700 Series. Freshel lens are available upon request. 12 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Notice ! Notice 1. Caution (Design) (1) Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. (2) Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. (3) In case of outdoor use, suitable optical filter and water and humidity proof structure should be applied. (4) To prevent failure or malfunction, please use a stabilized power supply. (5) Please avoid using the sensor in the following conditions because it may cause failure or malfunction. (a) in such a fluid as water, alcohol etc. corrosive gas (SO2, Cl2, NOX etc.) or sea breeze (b) in high humidity (c) in a place exposed directly to sunlight or headlights of automobile (d) in a place exposed to rapid ambient temperature change (e) in a place exposed directly to an air-conditioner or heat vent (f) strong vibrations (g) in a place exposed to strong electromagnetic field (h) in such a place where infrared ray is shaded (i) in any other place similar to the above (a) through (h) 2. Caution (Mounting) (1) Soldering (a) Hand soldering should be applied. (b) Soldering should be done quickly as following. Temperature of soldering iron : 350˚C Distance from can case 1 to 3mm Over 3mm Period of time Within 3 seconds per point Within 10 seconds per point (c) Soldering flux should be rosin flux and not contain more than 0.2wt% chlorine. Soldering flux should be removed after soldering. (2) Cleaning Soldering flux should be removed after soldering. Soldering flux may cause malfunction or degradation of character unless sufficiently cleaned. 3. Caution (Handling and Storage) (1) The optical filter of the sensor should not be scratched or soiled. (2) Strong shock should be avoided. (3) Electrostatics and strong electromagnetic field should be avoided. (4) The sensor should be kept on conductive sponge. (5) High temperature, high humidity, fluid such as water or alcohol etc., corrosive gas (SO2, Cl2, NOX etc.) and sea breeze should be avoided. 13 !Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering. S21E.pdf 05.11.16 Note: 1. Export Control For customers outside Japan No muRata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or otherwise contribution to (1) any weapons (Weapons of Mass Destruction (nuclear, chemical or biological weapons or missiles) or conventional weapons) or (2) goods or systems specially designed or intended for military end-use or utilization by military end-users. For customers in Japan For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required for export. < < > > 2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed above 3. Product specifications in this catalog are as of August 2005. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. 5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. http://www.murata.com/ Head Office 1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan Phone: 81-75-951-9111 International Division 3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: intl@murata.co.jp