TPS_CPCI-A-3U-200C

cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ SELECTION GUIDE Output Current1 　 Model Number Power 5V 3.3V 36A 12V 5A -12V 0.5A For full details go to www.murata-ps.com/rohs CPCI-A-3U-200C 200W 25A Yes Yes INPUT CHARACTERISTICS Parameter Input Operating Voltage Input Frequency Input Current Power Factor Inrush Current 230Vac 230Vac and 115Vac, full load 230Vac 0.98 50 Apk Conditions Auto range, single phase Min 90 47 Typ Max 264 63 3.5 Units Vac Hz Arms FEATURES 3Ux8HP package 200W power at -5 to 55ºC PICMG 2.11 Compliant Widerange 90-264VAC Input Active power factor correction to EN61000-3-2 Class B conducted EMI performance 47-pin I/O Connector 80% efficiency Full power with just 250lfm airflow Hot-swap capable OUTPUT CHARACTERISTICS Output V11 V2 1 Nominal Voltage +5.0Vdc +3.3Vdc +12Vdc -12Vdc Conditions All outputs 20MHz bandwidth 20MHz bandwidth 220Vac, full load Output Current Min 0A 0A 0A 0A Min Max 25A 36A 5A 0.5A Typ 0.5 Load Regulation1 ±1% ±1% ±4% ±4% Max Units % 75 120 mVp-p mVp-p msec 2 sec msec ±5 500 %Vnom μsec %Vnom mV ±10 % kVac kVac Vdc V31 V4 1 Parameter Line Regulation PARD (V1 & V2)4 PARD (V3 & V4)4 Hold-up Time Turn-on Delay 14 DESCRIPTION The cPCI-A-3U-200C is a high-reliability, 200W, continuous power, 3Ux8HP CompactPCI™ power supply developed for chassis’ with airflows as low as 250lfm. The use of 2 converters operating in parallel for the 3.3V and the 5V outputs enables maximum current draw on the two outputs simultaneously. Compliant with the PICMG 2.11 standard. With a widerange input of 90-264VAC, safety agency approvals to UL60950 and EN60950, EMI compliance to Class B FCC and EN55022 standards, the cPCI-A3U-300C was designed with globally-deployed systems in mind. Additional features include remote sense compensation, unit enable control (EN#), output inhibit control (INH#), output fault signal (FAL#), and thermal warning signal (DEG#). LEDs are provided for visual indication of input power presence and output fault condition. Rise Time Transient Response Over-Voltage and Short Circuit Protection5 Remote Sense Compensation2 Current Share Tolerance3 10% to 90% of full value ΔV, 50% load step Settling time V1, V2, & V3: Latching V1, V2 V1, V2 Pri-Sec 3 1.5 100 110 30 130 200 Isolation Pri-Chassis Sec-Chassis Notes: 1. Maximum combined power any combination of outputs is 200W 2. Maximum voltage compensation for cable losses . 3. Tolerance applicable up to 6 parallel units. Single wire current share on V1 & V2 for 50% to 100% load. 4. Measured across 1μF ceramic capacitor and 120μF electrolytic capacitor. 5. Automatic recovery upon removal of overload condition. www.murata-ps.com cPCI-A-3U-200C.A01 Page 1 of 4 cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ GENERAL CHARACTERISTICS Parameter Efficiency Conditions 230Vac, full load 120Vac, full load Switching Frequency MTBF Weight Main Converter Calculated per Bellcore standard B332 Gb 30ºC Unpackaged 300 800 Min Typ 80 76 68 kHz khrs g Max Units % PROTECTION Parameter Inrush Current Limit Input Protection Over-voltage Protection Parameter Output Overload Protection Hot-Swap Capability Output Fault Isolation Thermal Shutdown Conditions/Response 230VAC Internal line fuse V1, V2, & V3 with latched shutdown Conditions/Response Inception Min Typ Max 50 6.3 110 130 Units Arms Arms %Vnom Outputs are individually protected against overloads and indefinite short circuit with automatic recovery upon removal of the fault condition. Protected by internal ORing diodes Output isolation devices are present in all outputs to isolate faults within a failed power supply. Automatic recovery upon restoration to operational temperatures STATUS & CONTROL SIGNALS & INDICATORS Name Enable (EN#) Output Inhibit (INH#) Output Fault (FAL#) Remote Sense (RS+, RS-) Thermal Warning (DEG#) Description Contact closure to external ground to start unit. On shortest pin (last make, first break). TTL –compatible signal inhibited with GND or TTL “0”. TTL compatible signal ,open collector active low signal .Indicates one or more outputs below 90% of specified rate. Available on V1 & V2. Maximum voltage compensation for cable losses 200mV. Open collector active low 10ºC before power supply shut down. A single bi-color indicator LED Front Panel Power Indicator LED Green LED - indicates output in range Red LED - indicates one or more outputs below 90% of specified range. ENVIRONMENTAL CHARACTERISTICS Parameter Ambient Operating Temperature Ambient Storage Temperature Operating Humidity Storage Humidity Altitude Non-condensing Non-condensing Operating Storage Conditions Full load with 250LFM forced air and derating linearly above 55°C to 70°C, by 2.5% per °C Min -5 -40 Typ Max 55 85 95 95 6000 40000 Units ºC ºC % % ft ft www.murata-ps.com cPCI-A-3U-200C.A01 Page 2 of 4 cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ ELECTROMAGNETIC COMPATIBILITY (EMC) Characteristic Input Current Harmonics Conducted Emissions Electrostatic Discharge (ESD) Radiated Immunity Conducted Immunity Line Voltage Surge Conducted Disturbance Power Frequency Magnetic Field Line Voltage Interruptions Compliance EN61000-3-2 EN55022/CISPR22, Class B, with external TBD line filter EN61000-4-2, Level 4, 8kV air EN61000-4-3, Level 3, 10V/m EN61000-4-4, Level 3, ±2kV EN61000-4-5, Level 3, line-to-line 1kV line to chassis 2kV EN61000-4-6, Level 2, 3Vrms EN61000-4-8, 3A/m EN61000-4-11 CERTIFICATIONS Agency/Characteristic PENDING UL CSA CE RoHS Standard UL60950-1 CSA C22.2-234, Level 3 (per cUL) EN-60950, Class 1, SELV CE-Mark EN Directive 2002/95/EC; self-certified SAFETY AGENCY RATINGS Input Voltage Input Current 100-240Vac 3.5A MECHANICAL DIMENSIONS 6.43 1.60 2.50 169.60 17.63 40.34 3.10 POWER FORCED COOLING AIR 94.00 C L 100.00 128.60 Overall size: 169.6mm D x 128.6mm H x 40.3mm W (6.68” D x 5.06” H x 1.59” W) www.murata-ps.com cPCI-A-3U-200C.A01 Page 3 of 4 cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ CONNECTOR Pin 1-4 5-12 13-18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Pin Type Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Short Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Long Long Long Signal Name V1 RTN V2 RTN V3 V4 RTN RTN RTN GA-0 Reverse EN# GA-1 NC V1 Sense GA-2 NC V2 Sense S RTN V1 Share NC IPMB_SCL DEG# INH# IPMB_SDA V2 Share FAL# IPMB_PWR NC Chassis GND AC Neutral AC Line V1 Output V1 and V2 Return V2 Output V3 Return V3 Output V4 Output Signal Return Signal Return V4 Return Geographic ADD-0 (option) Reverse Enable Geographic ADD-1 (option) Not Connected V1 Remote Sense Geographic ADD-2 (option) Not Connected V2 Remote Sense Sense Return V1 Current Share Not Connected System Manager Bus (option) Degrade Signal Open – ON Low - OFF System Manager Bus (option) V2 Current Share Fail Signal System Manager (option) – Power Not Connected Chassis GND AC input Neutral AC Input Line RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300ºC for 10 seconds. The pin termination finish on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs ISO9001 CERTIFIED USA: Canada: UK: France: Germany: Japan: China: Singapore: Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED 10/24/08 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. www.murata-ps.com cPCI-A-3U-200C.A01 Page 4 of 4