TPS_CPCI-A-3U-300C

cPCI-A-3U-300C Series 300W 3Ux8HP AC/DC CompactPCI™ SELECTION GUIDE Output Current1 　 Model Number Power 5V 3.3V 40A 12V 5A -12V 0.5A For full details go to www.murata-ps.com/rohs CPCI-A-3U-300C 300W 30A Yes Yes INPUT CHARACTERISTICS Parameter Input Operating Voltage Input Frequency Input Current Power Factor Inrush Current 230Vac 0.98 Conditions Min 90 47 Typ Max 264 63 5.0 0.99 50 Units Vac Hz Arms Apk FEATURES 3Ux8HP package 300W power at 0-55ºC PICMG 2.11 Compliant Widerange 90-264VAC Input Active power factor correction to EN61000-3-2 Class B conducted EMI performance 47-pin I/O Connector 81% efficiency Full power with just 250lfm airflow Hot-swap capable OUTPUT CHARACTERISTICS Output V12 V22 V3 2 Nominal Voltage +5.0Vdc +3.3Vdc +12Vdc -12Vdc Conditions All outputs 20MHz bandwidth 20MHz bandwidth 230VAC, full load Output Current Min 0A 0A 0A 0A Min Max 30A 40A 5A 0.5A Typ 0.5 Load Regulation1 ±1% ±1% ±4% ±4% Max Units % 90 120 mVp-p mVp-p msec 2 sec msec ±5 500 %Vnom μsec %Vnom mV ±10 % kVac kVac Vdc V42 Parameter Line Regulation PARD (V1 & V2)5 PARD (V3 & V4)5 Hold-up Time Turn-on Delay Rise Time Transient Response Over-Voltage and Short Circuit Protection6 Remote Sense Compensation3 Current Share Tolerance 4 14 DESCRIPTION The cPCI-A-3U-300C is a high-reliability, 300W, continuous power, 3Ux8HP CompactPCI™ power supply developed for chassis’ with airflows as low as 250lfm. The use of 2 converters operating in parallel for the 3.3V and the 5V outputs enables maximum current draw on the two outputs simultaneously. Compliant with the PICMG 2.11 standard. With a widerange input of 90-264VAC, safety agency approvals to UL60950 and EN60950, EMI compliance to Class B FCC and EN55022 standards, the cPCI-A3U-300C was designed with globally-deployed systems in mind. Additional features include remote sense compensation, unit enable control (EN#), output inhibit control (INH#), output fault signal (FAL#), and thermal warning signal (DEG#). LEDs are provided for visual indication of input power presence and output fault condition. 10% to 90% of full value ΔV, 50% load step Settling time V1, V2, & V3: Latching V1, V2 V1, V2 Pri-Sec 3 1.5 100 110 30 130 300 Isolation Pri-Chassis Sec-Chassis Notes: 1. Total power limited to 300W. 2. Maximum combined power from V1 & V3 not to exceed 185W. Maximum combined power for V2 & V4 not to exceed 140W. 3. Maximum voltage compensation for cable losses . 4. Tolerance applicable up to 6 parallel units. Single wire current share on V1 & V2 for 50% to 100% load. 5. Measured across 10μF tantulum load capacitor paralleled with 0.1μF ceramic capacitor. 6. Automatic recovery upon removal of overload condition. www.murata-ps.com cPCI-A-3U-300C.A03 Page 1 of 4 cPCI-A-3U-300C Series 300W 3Ux8HP AC/DC CompactPCI™ GENERAL CHARACTERISTICS Parameter Efficiency Switching Frequency MTBF Weight Conditions Full load, 240Vac Main Converter Calculated per Bellcore standard B332 Gb 30ºC Unpackaged 300 840 Min Typ 81 68 Max Units % kHz khrs g PROTECTION Parameter Inrush Current Limit Input Protection Over-voltage Protection Parameter Output Overload Protection Hot-Swap Capability Output Fault Isolation Thermal Shutdown Conditions/Response 230VAC Internal line fuse V1, V2, & V3 with latched shutdown Conditions/Response Inception Min Typ Max 50 6.3 110 130 Units Arms Arms %Vnom Outputs are individually protected against overloads and indefinite short circuit with automatic recovery upon removal of the fault condition. Protected by internal ORing diodes Output isolation devices are present in all outputs to isolate faults within a failed power supply. Automatic recovery upon restoration to operational temperatures STATUS & CONTROL SIGNALS & INDICATORS Name Enable (EN#) Output Inhibit (INH#) Output Fault (FAL#) Remote Sense (RS+, RS-) Thermal Warning (DEG#) Description Short pin on connector will enable the outputs when the mating pin is grounded. Supply will not power up until this pin is engaged to its mate in the backplane. Unit output will be inhibited as pin is disengaged from the mating connector. Secondary referenced; active low, TTL compatible. Logic “0” or short circuit to output return inhibits all outputs. Secondary referenced; TTL compatible. Logic “0” denotes that one of the output voltages has fallen below the lower regulation limit. Connection of the sense leads across the load at the desired point of regulation will compensate for voltage distribution drops up to 200mV between the output terminals of the power supply and the point of connection. Secondary referenced; TTL compatible. Logic “0” denotes a thermal warning; nominally, 10ºC prior to thermal shutdown. A single bi-color Indicator LED Power Present Indicator LED Green LED - indicates output in range Red LED - indicates one or more outputs below 10% of specified range. ENVIRONMENTAL CHARACTERISTICS Parameter Ambient Operating Temperature Ambient Storage Temperature Operating Humidity Storage Humidity Altitude Non-condensing Non-condensing Operating Storage Conditions Full load with 250LFM forced air and derating linearly above 55°C to 70°C, by 2.5% per °C Min -5 -40 Typ Max 55 85 95 95 6000 40000 Units ºC ºC % % ft ft www.murata-ps.com cPCI-A-3U-300C.A03 Page 2 of 4 cPCI-A-3U-300C Series 300W 3Ux8HP AC/DC CompactPCI™ ELECTROMAGNETIC COMPATIBILITY (EMC) Characteristic Input Current Harmonics Conducted Emissions Electrostatic Discharge (ESD) Radiated Immunity Conducted Immunity Line Voltage Surge Line Voltage Interruptions Compliance EN61000-3-2 EN55022, Class B, with external line filter EN61000-4-2, Level 4 EN61000-4-3, Level 3 EN61000-4-4, Level 3, Criterion A EN61000-4-5, Level 3, line-to-line 1kV line to chassis 2kV EN61000-4-11 CERTIFICATIONS Agency/Characteristic PENDING UL CSA CE RoHS Standard UL60950-1 CSA C22.2-234, Level 3 (per cUL) EN-60950, Class 1, SELV CE-Mark EN Directive 2002/95/EC; self-certified SAFETY AGENCY RATINGS Input Voltage Input Current 100-240Vac 5A MECHANICAL DIMENSIONS 6.43 1.60 2.50 169.60 17.63 40.34 3.10 POWER FORCED COOLING AIR 94.00 C L 100.00 128.60 Overall size: 169.6mm D x 128.6mm H x 40.3mm W (6.68” D x 5.06” H x 1.59” W) www.murata-ps.com cPCI-A-3U-300C.A03 Page 3 of 4 cPCI-A-3U-300C Series 300W 3Ux8HP AC/DC CompactPCI™ CONNECTOR Pin1 1-4 5-12 13-18 19 20 21 22 23 24 25 26 27 28 293 30 31 323 33 34 35 36 373 38 39 403 41 42 433 443 45 46 47 Notes: RoHS COMPLIANCE INFORMATION Signal Name Description V1 RTN V2 RTN V3 V4 RTN RESERVED RTN GA0 RESERVED EN# GA1 V1ADJ V1 SENSE GA2 V2ADJ V2 SENSE S RTN V1 SHARE V3 SENSE IPMB SCL DEG# INH# IPMB SDA V2 SHARE FAL# IPMB PWR V3 SHARE CGND ACN/+DC IN ACL/-DC IN V1 Output V1 and V2 Return V2 Output V3 Return V3 Output V4 Output Signal Return Reserved V4 Return Geographic Address Bit 0 Reserved Enable Geographic Address Bit 1 V1 Adjust V1 Remote Sense Geographic Address Bit 2 V2 Adjust V2 Remote Sense Sense Return V1 Current Share V3 Remote Sense IPMB Serial Clock Line Degrade Signal Inhibit IPMB Serial Data Line V2 Current Share Fail Signal IPMB Power Input V3 Current Share Chassis Grnd (Safety Grnd) AC Input Neutral/+DC Input AC Input Line/-DC Input This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300ºC for 10 seconds. The pin termination finish on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs Staging 2 M M M M M M M M M M M S M M M M M M M M M M M M M M M M M L M M 1. Pin numbers correspond to the female backpane connector. 2. “L” denotes long pin length (first mate, last break) “M” denotes medium pin length “S” denotes short pin length (last mate, first break) 3. This function not used in the CPCI-A-3U-300C Series. ISO9001 CERTIFIED USA: Canada: UK: France: Germany: Japan: China: Singapore: Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED 02/04/09 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2009 Murata Power Solutions, Inc. www.murata-ps.com cPCI-A-3U-300C.A03 Page 4 of 4