TPS_PF600

PF600 SERIES 600W AC/DC Front-End Power Module OBSOLETE PRODUCT Contact factory for replacement model SELECTION GUIDE FEATURES Compact 2.55"x5"x0.56" package 600W power at -10ºC to +100ºC Power density >84W per in3 Up to 89% efficiency 90-264Vac global input range 12V at 50mA standby output DC OK signal Temperature monitoring output Harmonic correction to EN61000-3-2 cUL & VDE approved to 60950-1 Output remote ON/OFF control Model Number PF600-1 Power 600W Main Output 48V@12.5A Standby Output 12V@50mA Production Status Consult Factory d de n INPUT CHARACTERISTICS me igns m Parameter Conditions onditions s Min co des evironmen Input Operating Voltage oltage All line, load & environmental 85 t r new Input Frequency 47 y No r Input Current fo Power Factor Io>25% 0.95 >25% 1 Typ Max 264 66 5.5 Units Vac Hz Arms 0.98 0.99 10 2.5 44 Arms W W Inrush Current Quiescent Input Power 240Vac, avg. over 1 cycle SB output unloaded, output inhibited, 230Vac Output enabled but unloaded DESCRIPTION The PF600 AC-DC converter module provides a highlyintegrated, high-density solution for the front-end of a 48Vdc distributed power architecture (DPA). This unit delivers the full-rated 600W of output power over the input range of 90-264Vac while providing harmonic correction to EN61000-3-2. Unlike competitive offerings, the PF600 provides a fullisolated output, permitting implementations with either isolated or non-isolated DC-DC converters. The wide input voltage range of 85-264Vac facilitates use in products designed for global deployment. The isolated output also permits the user to polarize the output as the specific application may require. The high-efficiency architecture and baseplate-cooled design simplify thermal management. The lowprofile package makes this an ideal choice for 1U and 2U chassis applications where density and efficiency are strategic design considerations. Proprietary design techniques combined with automated manufacturing in fully ISO-9001 certified facilities results in a compact, reliable, and efficient product that provides a cost-effective solution. With global safety agency approvals, the PF600 is a comprehensive solution to a complex problem bounded by the competing pressures of development cycle time, efficiency, cost, and packagin d de Min n Output Power 90-264Vac 0-264Vac me igns0 m s st All line, load, temp, & 90% load step 36 mp, p, cotemload, 0-100ºC steep 44.5 Main Output Voltage (Vo) ) e00% static d0e 5%-100% 5%-1 rw Main Output Current (Io) ot 0 urre N r ne Vo sb) Standby Output Voltage (Vsb) 10 o urr ) Standby Output Current (Isb)f 0 OUTPUT CHARACTERISTICS Parameter Conditions PARD (Vo) PARD (Vsb) Turn-On Delay (Vo) 100kHz-20MHz Low freq ripple 20MHz bandwidth Ty Typ Max 600 Units W Vdc Vdc A Vdc mA mVp-p Vp-p 48 48 59 50.5 12.5 12 14 50 850 2.2 500 1 2 mVp-p sec msec kVac kVac Vac d de 3 n Isolation, Pri-Chassis 1.5 me igns1.5 ms Isolation, Sec-Chassis 500 o ec de r GENERAL CHARACTERISTICS t RACTE C ERISTICS o Conditions ew Parameter Min N rn o600W load, 90Vac lo f Efficiency Output Holdup Time Isolation, Pri-Sec Full load, 470uF bulk cap2 600W load, 264Vac Switching Frequency MTBF Weight Notes: 20 Typ 86 89 300 Max Units % % 255 MIL-HDBK-217F, 100ºC Unpackaged 436 345 kHz khrs 260 g 1 Full 600W power available at input voltages above 90Vac; de-rate output to 550W at 85Vac. 2 An external bulk capacitor is connected to terminals C+ and C- (pins 4 & 5) is required for operation. The minimum required capacitance is 100uF; the maximum value is 1000uF. The ripple current rating for this capacitor should exceed 3Arms at 300kHz. The minimum voltage rating for the bulk capacitor is 450Vdc. Additional information on holdup time is available in application note ACAN-10. www.murata-ps.com PF600.A01 Page 1 of 4 PF600 SERIES 600W AC/DC Front-End Power Module GENERAL CHARACTERISTICS Parameter Efficiency Switching Frequency MTBF Weight Conditions Full load, 240Vac PFC Converter Main Converter Calculated per Telcordia SR-332, Issue 1, 50ºC, 250lfm, ground benign Unpackaged 200 620 Min Typ 79 100 130 Max 81 Units % kHz kHz khrs g PROTECTION Parameter Conditions/Response Vo; output short circuit; automatic recovery3 Vsb; output short circuit; automatic recovery4 Automatic Recovery No damage will result from operation at voltages below the specified range. Available power will decrease below 90Vac, and at a voltage below 85Vac (typically 82Vac) the main output is switched off. An input fuse is required external to the PF600 module. Recommended maximum rating is 10A, 250V HBC. 100 Inception Min Typ 16 150 105 82 10 125 Max 20 Units A mA ºC Vac A Output Overload Protection5 Thermal Shutdown Input Undervoltage Protection Input Protection STATUS & CONTROL SIGNALS Name Remote ON/OFF Description An isolated pair (INH+, pin 10, and INH_, pin 11) provides for the inhibiting or enabling of the main output, Vo. Logic 1 (>3V) or leaving the pins open enables the output; a short between the pair or a logic 0 (