UEP-5-6000-D48

Single Output UEP Models Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s FEATURES n PRODUCT OVERVIEW The UEP Series DC/DC Converters deliver the most power/current (up to 30W/6Amps) from a 1" x 2" package. And because of their footprint compatibility, they can be used as drop in replacements for their bigger brothers, the standard 2" x 2" and 1.6" x 2" devices, commonly used in the industry. By combining a high-frequency (340kHz), high-efficiency (to 89%), synchronous-rectifier topology with the newest components and time-tested, fully automated, SMT-on-pcb construction, these UEP Models are able to bring you 15-30W in the standard 2" x 1" package from which most competitors can only get 5-10W. All UEP’s deliver their full output power over ambient temperature ranges from –40°C to as high as +70°C (model and input voltage dependent) without heat sinks or supplemental forced-air cooling. Devices derate to +100°C. Output voltages are 3.3, 5, 12 or 15 Volts. Input voltage ranges are 10-18V (“D12” models), 18-36V (“D24” models) or 36-75V (“D48”) models. All models feature input pi filters, input undervoltage and overvoltage lockout, input reverse-polarity protection, output overvoltage protection, output current Choice of 3 input ranges: 10-18V, 18-36V, 36-75V Models Include 3.3V @ 4.5A or 6A 5V @ 3.5A or 6A 15V @ 1.2A 12V @ 1.4A Guaranteed efficiencies to 89% 15-30 Watts in 1" x 2" package 340kHz synchronous-rectifier topologies –40 to +60/70°C ambient w/o derating Fully isolated (1500Vdc); I/O protected Trim and On/Off Control UL1950/EN60950 certified CE mark (75VIN models) n n n n n n n n n 　 limiting, and continuous short-circuit protection. Standard features also include on/off control and output-trim. All models are certified to IEC950, UL1950 and EN60950 safety requirements for OPERATIONAL insulation. “D48” models (36-75V inputs) are CE marked. UEP Series DC/DC’s are packaged in low-cost, light-weight, diallyl phthalate (UL94V-0 rated) plastic packages with standoffs. EMC compliance is achieved via a lownoise design rather than through expensive metal shielding. For full details go to www.murata-ps.com/rohs +INPUT (1) +OUTPUT (4) SWITCH CONTROL ➀ –OUTPUT (5) ➀ –INPUT (2) PWM CONTROLLER UVLO & OVLO COMPARATORS ON/OFF CONTROL (3) OPTO ISOLATION REFERENCE & ERROR AMP TRIM (6) ➀ 3.3V and 5V-output models use the synchronous-rectifier configuration shown above. 12V and 15V-output models employ a standard, diode-rectification architecture. Figure 1. Simplified Schematic Typical topology is shown. www.murata-ps.com Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 MDC_UEP Models.A02 Page 1 of 11 Single Output UEP Models Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s Performance Specifications and Ordering Guide ➀ Output Model UEP-3.3/4500-D12 UEP-3.3/4500-D24 UEP-3.3/4500-D48 UEP-3.3/6000-D48 UEP-5/3500-D12 UEP-5/3500-D24 UEP-5/3500-D48 UEP-5/6000-D48 UEP-12/1400-D12 UEP-12/1400-D24 UEP-12/1400-D48 UEP-15/1200-D12 UEP-15/1200-D24 Vout (Volts) 3.3 3.3 3.3 3.3 5 5 5 5 12 12 12 15 15 Iout (mA) 4500 4500 4500 6000 3500 3500 3500 6000 1400 1400 1400 1200 1200 R/N (mVp-p) Typ. 85 85 85 85 85 85 85 85 85 85 85 85 85 Max. 100 100 100 100 100 100 100 100 100 100 100 100 100 Regulation (Max.) Line ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% Load ➂ ±0.5% ±0.5% ±0.5% ±0.3% ±0.5% ±0.5% ±0.5% ±0.3% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% Vin Nom. (Volts) 12 24 48 48 12 24 48 48 12 24 48 12 24 Input Range (Volts) 10-18 18-36 36-75 36-75 10-18 18-36 36-75 36-75 10-18 18-36 36-75 10-18 18-36 Vout (mA) 80/1490 50/730 35/360 40/470 120/1760 65/850 40/430 35/710 60/1650 45/800 20/400 60/1760 45/860 Efficiency Min. 83.5% 85.5% 85.5% 86% 84% 86% 86% 88% 82.5% 85% 85% 82.5% 85% Typ. 84.5% 87.5% 87.5% 88% 86% 88% 88% 91% 85% 87% 87% 85% 87% Package (Case, Pinout) C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 C15, P21 ➀ Typical at TA = +25°C under nominal line voltage and full-load conditions, unless otherwise noted. ➁ Ripple/Noise (R/N) is tested/specifed over a 20MHz bandwidth. All models are specified with no external input/output capacitors. ➂ Load regulation is specified over no load to 100% load conditions for 3.3 and 5Vout models, 25mA to 100% load conditions for 12 and 15 Vout models. ➃ Nominal line voltage, no-load/full-load conditions. PART NUMBER STRUCTURE MECHANICAL SPECIFICATIONS 2.00 (50.80) PLASTIC CASE 0.49 (12.45) U EP - 3.3 / 4500 - D48 N - C Output Configuration: U = Unipolar External Pinout ROHS-6 Hazardous Substance Compliance N Suffix Available for 12Vout and 15Vout Models Input Voltage Range: D12 = 10-18 Volts (12V nominal) D24 = 18-36 Volts (24V nominal) D48 = 36-75 Volts (48V nominal) Maximum Output Current in mA 1.00 (25.40) Case C15 STANDOFF 0.020 (0.51) 0.20 MIN (5.08) 0.040 ±0.001 DIA. (1.016 ±0.025) 1.800 (45.72) 1 2 0.600 (15.24) 3 0.10 (2.54) Nominal Output Voltage: 3.3, 5, 12 or 15 Volts 4 5 0.400 (10.16) 0.800 (20.32) 0.400 (10.16) 6 0.100 (2.54) BOTTOM VIEW 0.10 (2.54) DIMENSIONS ARE IN INCHES (MM) Optional Functions UEP converters are designed such that the 12 and 15Vout models can be configured for either positive logic on/off control (no suffix) or negative logic (“N” suffix). 3.3 and 5Vout models are available with positive logic only (no suffix). No Suffix On/Off Control function (positive polarity) on pin 3 N On/Off Control function (negative polarity) on pin 3. (12V and 15V models only.) I/O Connections Pin 1 2 3 4 5 6 Function P21 +Input –Input On/Off Control +Output –Output Trim www.murata-ps.com Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 MDC_UEP Models.A02 Page 2 of 11 Single Output UEP Models Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s Performance/Functional Specifications Typical @ TA = +25°C under nominal line voltage and full-load conditions, unless noted. ➀ ➁ Input Input Voltage Range: D12 Models D24 Models D48 Models Overvoltage Shutdown: D12 Models D24 Models D48 Models ➆ Start-Up Threshold: ➂ D12 Models D24 Models D48 Models Undervoltage Shutdown: ➂ D12 Models D24 Models D48 Models Input Current: Normal Operating Conditions Standby Mode (Off, OV, UV) Input Filter Type Reverse-Polarity Protection On/Off Control (Optional, Pin 3): ➃ D12, D24, & D48 Models D12N, D24N, & D48N Models 10-18 Volts (12V nominal) 18-36 Volts (24V nominal) 36-75 Volts (48V nominal) 18.5-21 Volts (20V typical) 37-40 Volts (38V typical) 77-81 Volts (78.5V typical) 9.3-9.8 Volts (9.6V typical) 16.5-18 Volts (17V typical) 34-36 Volts (35V typical) 7-8.5 Volts (8V typical) 15.5-17.5 Volts (16.5V typical) 32.5-35.5 Volts (34.5V typical) See Ordering Guide 5mA Pi Brief duration, 10A maximum On = open or 13V - +VIN, IIN = 50µA max. Off = 0-0.8V, IIN = 1mA max. On = 0-0.5V, IIN = 50µA max. Off = open or 2.4-10V, IIN = 3.7mA max. Switching Frequency 6A Models 1.2A-4.5A Models Dynamic Characteristics (continued) 400kHz (±20kHz) 340kHz (±40kHz) Environmental Operating Temperature (Ambient): Without Derating ➅ With Derating Case Temperature: Maximum Allowable Storage Temperature Dimensions Shielding Case Material Pin Material Weight ➀ ➁ ➂ ➃ –40 to +60/70°C to +100°C (See Derating Curves) +100°C –40 to +105°C Physical 2" x 1" x 0.51" (51 x 25 x 12.95mm) None Diallyl phthalate, (UL94V-0 rated) Gold-plated copper alloy with nickel underplate 1.4 ounces (39.7 grams) Output VOUT Accuracy (50% load): Minimum Loading: ➁ 3.3V/5V Outputs 12V/15V Outputs Ripple/Noise (20MHz BW) ➀ ➄ Line/Load Regulation Efficiency Isolation Voltage: Input-to-Output Isolation Capacitance Isolation Resistance Current Limit Inception: ➂ 6A Models 4.5A Models 3.5A Models 1.4A Models 1.2A Models Short Circuit: ➂ Average Current VOUT Trim Range ➂ Overvoltage Protection ➂ Temperature Coefficient Transient Response (50-100% load) Start-Up Time: ➂ VIN to VOUT On/Off to VOUT ±1.5%, maximum No load 25mA See Ordering Guide See Ordering Guide See Ordering Guide 1500Vdc minimum 470pF 100MW 7-8 Amps 5.5-7 Amps (6.25 Amps typ.) 5.5-6 Amps (5.25 Amps typ.) 1.9-2.7 Amps (2.3 Amps typ.) 1.5-2.1 Amps (1.8 Amps typ.) Hiccup, indefinite 3 Amps maximum ±5% Zener/transorb clamp, magnetic feedback ±0.02% per °C.Dynamic Characteristics All models are specified with no external input/output capacitors. See Minimum Output Loading Requirements under Technical Notes. See Technical Notes for details. The On/Off Control is designed to be driven with open-collector logic or the application of appropriate voltages (referenced to –Input (Pin 2)). Applying a voltage to the On/Off Control pin when no input voltage is applied to the converter may cause permanent damage. See Technical Notes. ➄ Output noise may be further reduced with the addition of external output capacitors. See Technical Notes. ➅ Operating temperature range without derating is model and input-voltage dependent. See Temperature Derating. ➆ UEP-3.3/600-D48 and UEP-5/6000-D48 do not have overvoltage shutdown. See Absolute Maximum Ratings for allowable input voltages. Absolute Maximum Ratings Input Voltage: Continuous: D12 Models D24 Models D48 Models Transient (100msec): D12 Models D24 Models D48 Models Input Reverse-Polarity Protection Output Overvoltage Protection: 3.3V Outputs 5V/12V/15V Outputs Output Current Case Temperature Storage Temperature Lead Temperature (soldering, 10 sec.) 22 Volts 44 Volts 88 Volts 22 Volts 44 Volts 88 Volts Current must be