MU9C1485A-90TCI

Preliminary Data Sheet WidePort LANCAM® Family APPLICATION BENEFITS Enhances Ethernet and Token-Ring LAN bridges and switches: Ø 64-bit width stores 48-bit MAC address plus associated data (Port ID, time stamp, “permanent” flag) Ø 32-bit I/O supports multiple ports of fast (100 Mb) Ethernet or Gigabit Ethernet Ø Station list depth flexibility with choice of pin-compatible device densities and glue-free cascading Ø 3.3 Volt option for low power systems Ø Industrial temperature grades for harsh environments DISTINCTIVE CHARACTERISTICS Ø 4096 (4485A/L), 2048 (2485A/L), and 1024 (1485A/L) word CMOS content-addressable memories (CAMs) Ø 64-bit word width Ø 32-bit I/O compatible with the MU9C1485 Ø Fast 50 ns compare speed Ø Dual configuration register set for rapid context switching Ø Increased flexibility of MUSIC’s patented CAM/RAM partitioning Ø 80-pin TQFP package with the same pinout as the MU9C1485 and MU9C1965A/L Ø 5 volt (A) or 3.3 volt (L) operation (3 2 ) M UX D ATA (6 4 ) I/ O B U FF E R S DQ 3 1 – 0 (3 2 ) (3 2 ) TRA N S L A TE (8 02 .3 /8 0 2 .5 ) DE M U X D ATA (6 4 ) (3 2 ) S O U R CE AN D D E S TINA TIO N S EG M ENT C O U N TE R S C O M P AR A ND M AS K R E G IS TE R 1 M AS K R E G IS TE R 2 3 2 K o r 1 6 K X 2 V AL ID I TY B ITS C O MM AN D S & S TA TU S AD D R E S S D E C O D E R /W /E /CM /EC /R E S E T 17/ 16 /M A P R I OR I TY E N CO D E R /M M 2 CO NT RO L LO G I C CO NT RO L AND S T AT US RE G IS T ER S CAM A RR AY 3 2 K or 1 6 K W O RD S X 6 4 B ITS 15/ 14 / FF F LA G L O G IC / FI /M F /M I Block Diagram LANCAM, the MUSIC logo, and the phrase “MUSIC Semiconductors” are registered trademarks of MUSIC Semiconductors. MUSIC is a trademark of MUSIC Semiconductors. Certain features of this device are patented under US Patent 5,383,146. 2 December 1998 Rev. 2 WidePort LANCAM® Family GENERAL DESCRIPTION The MU9C4485A/L, MU9C2485A/L, and MU9C1485A/L WidePort LANCAMs are 64-bit wide content-addressable memories (CAMs), featuring a 32-bit wide interface. This interface doubles the available I/O bandwidth in many applications while maintaining the same powerful enhanced architecture and instruction set as the MU9C2480A/L. Content-addressable memories, also known as associative memories, operate in the converse way to random access memories (RAM). In a RAM, the input to the device is an address and the output is the data stored at that address. In a CAM, the input is a data sample and the output is a flag to indicate a match and the address of the matching data. As a result, a CAM searches large databases for matching data in a short, constant time period, no matter how many entries are in the database. The ability to search data words up to 64 bits wide allows large address spaces to be searched rapidly and efficiently. A patented architecture links each CAM entry to associated data and makes this data available for use after a successful compare operation. While the WidePort LANCAMs are optimized for LAN network address filtering, they are also well suited for applications that require high-speed data searching, such as virtual memories and cache management, data compression and encryption, database accelerators, and image processing. OPERATIONAL OVERVIEW To use the WidePort LANCAM, the user loads the data into the Comparand register, which is automatically compared to all valid CAM locations. The device then indicates whether or not one or more of the valid CAM locations contains data that match the target data. The status of each CAM location is determined by two validity bits at each memory location. The two bits are encoded to render four validity conditions: Valid, Skip, Empty, and Random Access, as shown in Table 1. The memory can be partitioned into CAM and associated RAM segments on 16-bit boundaries, but by using one of the two available mask registers, the CAM/RAM partitioning can be set at any arbitrary size between zero and 64 bits. The WidePort LANCAM’s internal data path is 64 bits wide for rapid internal comparison and data movement. A data translation facility converts between IEEE 802.3 (CSMA/CD “Ethernet”) and 802.5 (Token Ring) address formats. Vertical cascading of additional WidePort LANCAMs in a daisy chain fashion extends the CAM memory depth for large databases. Cascading requires no external logic. Loading data to the Control, Comparand, and mask registers automatically triggers Skip Bit 0 0 1 1 Empty Bit 0 1 0 1 Entry Type Valid Empty Skip RAM a compare. Compares may also be initiated by a command to the device. Associated RAM data is available immediately after a successful compare operation. The Status register reports the results of compares including all flags and addresses. Two mask registers are available and can be used in two different ways: to mask comparisons or to mask data writes. The random access validity type allows additional masks to be stored in the CAM array where they may be retrieved rapidly. A simple four-wire control interface and commands loaded into the Instruction decoder control the device. A powerful instruction set increases the control flexibility and minimizes software overhead. Additionally, dedicated pins for match and multiple-match flags enhance performance when the device is controlled by a state machine. These and other features make the WidePort LANCAM a powerful associative memory that drastically reduces search delays. G ND D Q8 D Q7 D Q6 D Q5 D Q4 D Q3 D Q2 D Q1 D Q0 G ND G ND G ND 42 G ND 41 V CC V CC /C M 45 / MA 44 /EC / FI 43 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 G ND G ND D Q9 D Q 10 D Q 11 NC V CC V CC TE S T2 NC G ND G ND D Q 12 D Q 13 G ND G ND 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 NC / FF / MI / MF / MM G ND G ND /R ESET V CC V CC /E /W V CC V CC TE S T1 NC D Q 31 D Q 30 G ND G ND 80-Pin TQFP 8 0 -P IN TQ FP (Top V ie w ) (Top View) Table 1: Entry Types vs. Validity Bits /W LOW LOW HIGH HIGH /CM Cycle Type LOW Command Write Cycle HIGH Data Write Cycle LOW Command Read Cycle HIGH Data Read Cycle Table 2: I/O Cycles D Q 14 D Q 15 D Q 16 NC 10 11 12 13 14 15 16 17 18 D Q 28 19 D Q 29 D Q 17 D Q 18 D Q 19 D Q 20 V CC D Q 21 D Q 22 D Q 23 D Q 24 D Q 25 GN D D Q 26 D Q 27 GN D GN D GN D GN D Pinout Diagram Rev. 2 2 GN D 20 1 2 3 4 5 6 7 8 9 WidePort LANCAM® Family PIN DESCRIPTIONS All signals are implemented in CMOS technology with TTL levels. Signal names that start with a slash (“/”) are active LOW. Inputs should never be left floating. The CAM architecture draws large currents during compare operations, mandating the use of good layout and bypassing techniques. Refer to the Electrical Characteristics section for more information. /E (Chip Enable, Input, TTL) The /E input enables the device while LOW. The falling edge registers the control signals /W, /CM, /EC. The rising edge locks the daisy chain, turns off the DQ pins, and clocks the Destination and Source Segment counters. The four cycle types enabled by /E are shown in Table 2. /W (Write Enable, Input, TTL) The /W input selects the direction of data flow during a device cycle. /W LOW selects a Write cycle and /W HIGH selects a Read cycle. /CM (Data/Command Select, Input, TTL) The /CM input selects whether the input signals on DQ31–0 are data or commands. /CM LOW selects Command cycles and /CM HIGH selects Data cycles. /EC (Enable Daisy Chain, Input, TTL) The /EC signal performs two functions. The /EC input enables the /MF output to show the results of a comparison, as shown in Figure 6. If /EC is LOW at the falling edge of /E in a given cycle, the /MF output is enabled. Otherwise, the /MF output is held HIGH. The /EC signal also enables the /MF–/MI daisy chain, which serves to select the device with the highest-priority match in a string of LANCAMs. Tables 6a and 6b explain the effect of the /EC signal on a device with or without a match in both Standard and Enhanced modes. /EC must be HIGH during initialization. DQ31–0 (Data Bus, Three-state I/O, TTL) The DQ31–0 lines convey data, commands, and status to and from the WidePort LANCAM, as shown in Table 3. /W and /CM control the direction and nature of the information that flows to or from the device. When /E is HIGH, DQ31–0 go to HIGH-Z. /MF (Match Flag, Output, TTL) The /MF output goes LOW when one or more valid matches occur during a compare cycle. /MF becomes valid after /E goes HIGH on the cycle that enables the daisy chain (on the first cycle that /EC is registered LOW by the previous falling edge of /E; see Figure 6). In a daisy chain, valid match(es) in higher priority devices are passed from the /MI input to /MF. If the daisy chain is enabled but the match flag is disabled in the Control register, the /MF output only depends on the /MI input 3 of the device (/MF=/MI). /MF is HIGH if there is no match or when the daisy chain is disabled (/E goes HIGH when /EC was HIGH on the previous falling edge of /E). The System Match flag is the /MF pin of the last device in the daisy chain. /MF will be reset when the active configuration register set is changed. /MI (Match Input, Input, TTL) The /MI input prioritizes devices in vertically cascaded systems. It is connected to the /MF output of the previous device in the daisy chain. The /MI pin on the first device in the chain must be tied HIGH. /MA (Device Match Flag, Output, TTL) The /MA output is LOW when one or more valid matches occur during the current or the last previous compare cycle. The /MA output is not qualified by /EC or /MI, and reflects the match flag from that specific device’s Status register. /MA will be reset when the active register set is changed. /MM (Device Multiple Match Flag, Output, TTL) The /MM output is LOW when more than one valid match occurs during the current or the last previous compare cycle. The /MM output is not qualified by /EC or /MI, and reflects the multiple match flag from that specific device’s Status register. /MM will be reset when the active register set is changed. /FF (Full Flag, Output, TTL) If enabled in the Control register, the /FF output goes LOW when no empty memory locations exist within the device (and in the daisy chain above the device as indicated by the /FI pin). The System Full flag is the /FF pin of the last device in the daisy chain, and the Next Free address resides in the device with /FI LOW and /FF HIGH. If disabled in the Control register, the /FF output only depends on the /FI input (/FF = /FI). /FI (Full Input, Input, TTL) The /FI input generates a CAM-Memory-System-Full indication in vertically cascaded systems. It is connected to the /FF output of the previous device in the daisy chain. The /FI pin on the first device in a chain must be tied LOW. Rev. 2 WidePort LANCAM® Family PIN DESCRIPTIONS Continued /RESET (Reset, Input, TTL) /RESET must be driven LOW to place the device in a known state before operation, which will reset the device to the conditions shown in Table 5. The /RESET pin should be driven by TTL levels, not directly by an RC timeout. /E must be kept HIGH during /RESET. TEST1, TEST2 (Test, Input, TTL) These pins enable MUSIC production test modes that are not usable in an application. They should be connected to ground, either directly or through a pull-down resistor, or they may be left unconnected. These pins may not be implemented on all versions of these products. VCC, GND (Positive Power Supply, Ground) These pins are the power supply connections to the WidePort LANCAM. VCC must meet the voltage supply requirements in the Operating Conditions section relative to the GND pins, which are at 0 Volts (system reference potential), for correct operation of the device. All the ground and power pins must be connected to their respective planes with adequate bulk and high frequency bypassing capacitors in close proximity to the device. The MU9C2485A/L and MU9C1485A/L are compatible with the original MU9C1485 connections, and may be operated at -90 or slower switching characteristics without the GND connections on pins 1, 2, 20, 21, 22, 41, 42, 60, 61, and 62. FUNCTIONAL DESCRIPTION The WidePort LANCAM is a content-addressable memory (CAM) with 32-bit I/O for network address filtering, virtual memory, data compression, caching, and table lookup applications. The memory consists of static CAM, organized in 64-bit data fields. Each data field can be partitioned into a CAM and a RAM subfield on 16-bit boundaries. The contents of the memory can be randomly accessed or associatively accessed by the use of a compare. During automatic comparison cycles, data in the Comparand register is automatically compared with the “Valid” entries in the memory array. The Device ID can be read using a TCO PS instruction (see Table 13). The data inputs and outputs of the WidePort LANCAM are multiplexed for data and instructions over a 32-bit I/O bus. Internally, data is handled on a 64-bit basis, since the Comparand register, the mask registers, and each memory entry are 64 bits wide. Memory entries are /W LOW /CM LOW Cycle Type Command write “f” Bit 0 1 0 1 X X X X globally configurable into CAM and RAM segments on 16-bit boundaries, as described in US Patent 5,383,146 assigned to MUSIC Semiconductors. Seven different CAM/RAM splits are possible, with the CAM width going from one to four segments, and the remaining RAM width going from three to zero segments. Finer resolution on compare width is possible by invoking a mask register during a compare, which does global masking on a bit basis. The CAM subfield contains the associative data, which enters into compares, while the RAM subfield contains the associated data, which is not compared. In LAN bridges, the RAM subfield can hold, for example, port-address and aging information related to the destination or source address information held in the CAM subfield of a given location. In a translation application, the CAM field can hold the dictionary entries, while the RAM field holds the translations, with almost instantaneous response. DQ31–16 Non-TCO Instruction Non-TCO Instruction TCO Instruction (Read register)* TCO Instruction (Write register) Status Register bits 31–16 Status Register bits 31–16† Data to CR, MRX, Mem. Data from CR, MRX, Mem. DQ15–0 XXXX Absolute Address XXXX Value to Register Status Register bits 15–0 Register contents* Data to CR, MRX, Mem. Data from CR, MRX, Mem. HIGH LOW HIGH Notes: LOW HIGH HIGH Command read TCO 2nd cycle Data write Data read * A CW of a TCO Instruction with the “f” bit set to 0 sets up a Register read in the following cycle. The following cycle must be a Command Read cycle, otherwise the register read will be cancelled. † Upper 16 bits will be Status Register bits 31–16, except for a read of the Page Address register, in which case they will be all zeros. Table 3: DQ Bus Multiplexing Rev. 2 4 WidePort LANCAM® Family FUNCTIONAL DESCRIPTION Continued Each entry has two validity bits (known as Skip bit and Empty bit) associated with it to define its particular type: empty, valid, skip, or RAM. When data is written to the active Comparand register, and the active Segment Control register reaches its terminal count, the contents of the Comparand register are automatically compared with the CAM portion of all the valid entries in the memory array. For added versatility, the Comparand register can be barrel-shifted right or left one bit at a time. A Compare instruction can then be used to force another compare between the Comparand register and the CAM portion of memory entries of any one of the four validity types. After a Read or Move from Memory operation, the validity bits of the location read or moved will be copied into the Status register, where they can be read from the Status register using Command Read cycles. Data can be moved from one of the data registers (CR, MR1, or MR2) to a memory location that is based on the results of the last comparison (Highest-Priority Match or Next Free), or to an absolute address, or to the location pointed to by the active Address register. Data can also be written directly to the memory from the DQ bus using any of the above addressing modes. The Address register may be directly loaded and may be set to increment or decrement, allowing DMA-type reading or writing from memory. Two sets of configuration registers (Control, Segment Control, Address, Mask Register 1, and Persistent Source and Destination) are provided to permit rapid context switching between foreground and background activities. Writes, reads, moves, and compares are controlled by the currently active set of configuration registers. The foreground set would typically be preloaded with values useful for comparing input data, often called filtering, while the background set would be preloaded with values useful for housekeeping activities such as purging old entries. Moving from the foreground task of filtering to the background task of purging can be done by issuing a single instruction to change the current set of configuration registers. The match condition of the device is reset whenever the active register set is changed. The active Control register determines the operating conditions within the device. Conditions set by this register’s contents are reset, enable or disable Match flag, enable or disable Full flag, default data translation, CAM/RAM partitioning, disable or select masking conditions, disable or select auto-incrementing or 5 auto-decrementing the Address register, and select Standard (compatible with the MU9C1485) or Enhanced mode. The active Segment Control register contains separate counters to control the writing of 32-bit data segments to the selected persistent destination, and to control the reading of 32-bit data segments from the selected persistent source. There are two active mask registers at any one time, which can be selected to mask comparisons or data writes. Mask Register 1 has both a foreground and background mode to support rapid context switching. Mask Register 2 does not have this mode, but can be shifted left or right one bit at a time. For masking comparisons, data stored in the active selected mask register determines which bits of the comparand are compared against the valid contents of the memory. If a bit is set HIGH in the mask register, the same bit position in the Comparand register becomes a “don’t care” for the purpose of the comparison with all the memory locations. During a Data Write cycle or a MOV instruction, data in the specified active mask register can also determine which bits in the destination will be updated. If a bit is HIGH in the mask register, the corresponding bit of the destination is unchanged. The match line associated with each memory address is fed into a priority encoder where multiple responses are resolved, and the address of the highest-priority responder (the lowest numerical match address) is generated. In the LAN bridge application, a multiple response might indicate an error. In other applications the existence of multiple responders may be valid. Four input control signals and commands loaded into an instruction decoder control the WidePort LANCAM. Two of the four input control signals determine the cycle type. The control signals tell the device whether the data on the I/O bus represents data or a command, and is input or output. Commands are decoded by instruction logic and control moves, forced compares, validity bit manipulations, and the data path within the device. Registers (Control, Segment Control, Address, Next Free Address, etc.) are accessed using Temporary Command Override instructions. The data path from the DQ bus to/from data resources (comparand, masks, and memory) within the device are set until changed by Select Persistent Source and Destination instructions. After a Compare cycle (caused by either a data write to the Comparand or mask registers, a write to the Control register, or a forced compare), the Status register contains the Rev. 2 WidePort LANCAM® Family FUNCTIONAL DESCRIPTION Continued address of the Highest-Priority Matching location in that device, concatenated with its page address, along with flags indicating internal match, multiple match, and full. When the Status register is read with a Command Read cycle, the device with the Highest-priority match will respond, outputting the System Match address to the DQ bus. The internal Match (/MA) and Multiple match (/MM) flags are also output on pins. Another set of flags (/MF and /FF) that are qualified by the match and full flags of previous devices in the system are also available directly on output pins, and are independently daisy-chained to provide System Match and Full flags in vertically cascaded LANCAM arrays. In such arrays, if no match occurs during a comparison, read access to the memory and all the registers except the Next Free register is denied to prevent device contention. In a daisy chain, all devices will respond to Command and Data Write cycles, depending on the conditions shown in Tables 6a and 6b, unless the operation involves the Highest-Priority Match address or the Next Free address; in which case, only the specific device having the Highest-Priority match or the Next Free address will respond. A Page Address register in each device simplifies vertical expansion in systems using more than one LANCAM. This register is loaded with a specific device address during system initialization, which then serves as the higher-order address bits. A Device Select register allows the user to target a specific device within a vertically cascaded system by setting it equal to the Page Address Register value, or to address all the devices in a string at the same time by setting the Device Select value to FFFFH. Figure 1a shows expansion using a daisy chain. Note that system flags are generated without the need for external logic. The Page Address register allows each device in the vertically cascaded chain to supply its own address in the event of a match, eliminating the need for an external priority encoder to calculate the complete Match address at the expense of the ripple-through time to resolve the highestpriority match. The Full flag daisy-chaining allows Associative writes using a Move to Next Free Address instruction which does not need a supplied address. Figure 1b shows an external PLD implementation of a simple priority encoder that eliminates the daisy chain ripplethrough delays for systems requiring maximum performance from many CAMS. V cc Vcc 32 D Q 31 -0 /E /W /C M /EC D Q 31 -0 /E /W /C M /EC W id e p o r t L AN C AM / MI /MI / FI / FF / MF W ide P ort LA N C A M /MA P LD D Q 31 -0 /E /W /C M /EC W id e p o r t L AN C AM / MI /MI / FI / FF / MF W ide P ort LA N C A M /MA /MI W ide P ort LA N C A M /MA D Q 31 -0 /E /W /C M /EC W id e p o r t L AN C AM / MI / FI / FF / MF S YS TE M F U L L S YS TE M MATC H /MI W ide P ort LA N C A M /MA S Y S TE M M A TC H Figure 1a: Vertical Cascading Figure 1b: External Prioritizing Rev. 2 6 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Throughout the following, “aaaH” represents a threedigit hexadecimal number “aaa,” while “bbB” represents a two-digit binary number “bb.” All memory locations are written to or read from in 32-bit segments. Segment 0 corresponds to the lowest order bits (bits 31–0) and Segment 1 corresponds to the highest order bits (bits 63–32). Address register read where 0s will be read on DQ31–16 instead), as shown in Table 3. The data and control interfaces to the WidePort LANCAM are synchronous. During a Write cycle, the Control and Data inputs are registered by the falling edge of /E. When writing to the persistently selected data destination, the Destination Segment counter is clocked by the rising edge of /E. During a Read cycle, the Control inputs are registered by the falling edge of /E, and the Data outputs are enabled while /E is LOW. When reading from the persistently selected data source, the Source Segment counter is clocked by the rising edge of /E. THE CONTROL BUS Refer to the Block Diagram for the following discussion. The inputs Chip Enable (/E), Write Enable (/W), Command Enable (/CM), and Enable Daisy Chain (/EC) are the primary control mechanism for the WidePort LANCAM. The /EC input of the Control bus enables the /MF Match flag output when LOW and controls the daisy chain operation. Instructions are the secondary control mechanism. Logical combinations of the Control Bus inputs, coupled with the execution of Select Persistent Source (SPS), Select Persistent Destination (SPD), and Temporary Command Override (TCO) instructions allow the I/O operations to and from the DQ31–0 lines to the internal resources, as shown in Table 4. The Comparand register is the default source and destination for Data Read and Write cycles. This default state can be overridden independently by executing a Select Persistent Source or Select Persistent Destination instruction, selecting a different source or destination for data. Subsequent Data Read or Data Write cycles will access that source or destination until another SPS or SPD instruction is executed. The currently selected persistent source or destination can be read back through a TCO PS or PD instruction. The sources and destinations available for persistent access are those resources on the 64-bit bus: Comparand register, Mask Register 1, Mask Register 2, and the Memory array. The default destination for Command Write cycles is the Instruction decoder, while the default source for Command Read cycles is the Status register. The entire 32-bit Status register is read in a single cycle. Temporary Command Override (TCO) instructions provide access to the Control register, the Page Address register, the Segment Control register, the Address register, the Next Free Address register, and Device Select register. These instructions are only active for one Command Write cycle to write a value into a register, or one Command Write cycle followed by a Command Read cycle to read a register’s contents. Each of these 16-bit registers is read out on the DQ15–0 pins, with the upper 16 bits of the Status register output on the DQ31–16 pins (except in the case of a Page 7 THE REGISTER SET The Control, Segment Control, Address, Mask Register 1, and the Persistent Source and Destination registers are duplicated, with one set termed the Foreground set, and the other the Background set. The active set is chosen by issuing Select Foreground Registers or Select Background Registers instructions. By default, the Foreground set is active after a reset. Having two alternate sets of registers that determine the device configuration allows for a rapid return to a foreground network filtering task from a background housekeeping task. Writing a value to the Control register or writing data to the last segment of the Comparand or either mask register will cause an automatic comparison to occur between the contents of the Comparand register and the words in the CAM segments of the memory marked valid, masked by MR1 or MR2 if selected in the Control register. Instruction Decoder The Instruction decoder is the write-only decode logic for instructions and is the default destination for Command Write cycles using the DQ31–16 lines. If the instruction requires an absolute address or register value, the “f” Address Field flag (bit 11) of the instruction is set to a “1,” and the data on the DQ15–0 lines are written to the proper register in that same cycle. If the instruction written is a TCO, and the “f” bit is not set, the contents of the register specified by the TCO may be read back by a successive Command Read cycle to the DQ15–0 signal lines. If the Address Field flag is set in a memory access instruction, the absolute address supplied on the DQ15–0 lines is loaded into the Address register, and the instruction completes at the new address. If the Address Field flag is not set, the memory access occurs at the address currently Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued Cycle Type /E Cmd Write L /CM /W L L I/O Status SPS SPD TCO Operation Notes IN Load Instruction decoder 1 IN 2 ü Load Address register 2 IN Load Control register ü 2 IN Load Page Address register ü 2 IN Load Segment Control register ü IN 2 ü Load Device Select register IN Deselected 9 OUT 3 ü Read Next Free Address register 3 OUT ü Read Address register 4 OUT Read Status Register bits 31–0 3 OUT Read Control register ü OUT Read Page Address register 3 ü OUT Read Segment Control register 3 ü OUT Read Device Select register 3 ü OUT ü Read Current Persistent Source or Destination 3, 10 9 HIGH-Z Deselected 5, 8 IN Load Comparand register ü IN Load Mask Register 1 6, 8 ü IN Load Mask Register 2 6, 8 ü IN Write Memory Array at address 6, 8 ü 6, 8 IN Write Memory Array at Next Free address ü 6, 8 IN Write Memory Array at Highest-Priority match ü 9 IN Deselected OUT Read Comparand register 5, 8 ü OUT Read Mask Register 1 7, 8 ü OUT Read Mask Register 2 ü 7, 8 7, 8 OUT Read Memory Array at address ü 7, 8 OUT Read Memory Array at Highest-Priority match ü HIGH-Z Deselected 9 HIGH-Z Deselected Cmd Read L L H Data Write L H L Data Read L H H H X X Notes: 1. Default Command Write cycle destination (does not require a TCO instruction). 2. To load a value into a register using a TCO instruction takes one Command Write cycle with the “f” bit equal to 1, and the value to be loaded into the selected register placed in DQ15–0. 3. Reading the contents of a register using a TCO instruction takes two cycles. The first cycle is a Command Write of a TCO instruction with the “f” bit equal to 0. If the next cycle is a Command Read, the value stored in the selected register will be read out on the DQ15–0 lines. Additionally, bits 31–16 of the Status register will be read out on the DQ31–16 lines, except in the case of a Page Address read where 0s will be read on DQ31–16 instead. 4. Default Command Read cycle source (does not require a TCO instruction). 5. Default persistent source and destination after Reset. If other resources were sources or destinations, SPD CR or SPS CR restores the Comparand register as the destination or source. 6. Selected by executing a Select Persistent Destination instruction. 7. Selected by executing a Select Persistent Source instruction. 8. Access is performed in one or two 32-bit Read or Write cycles. The Segment Control register is used to control the selection of the desired 32-bit segement(s) by establishing the Segment counters’ limits and start values. 9. Device is deselected if Device Select register setting does not equal Page Address register setting, unless the Device Select register is set to FFFFH which allows only write access to the device, except in the case of a match. (Writes to the Device Select register are always active.) Device may also be deselected under locked daisy chain conditions as shown in Tables 6a and 6b. 10. A Command Read cycle after a TCO PS or TCO PD reads back the Instruction decoder bits that were last set to select a persistant source or destination. The TCO PS instruction will also read back the Device ID. Table 4: Input/Output Operations Rev. 2 8 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued CAM Status Validity bits at all memory locations Match and Full flag outputs IEEE 802.3-802.5 Input Translation CAM/RAM Partitioning Comparison Masking Address register auto-increment or -decrement Source and Destination Segment counters count ranges Address register and Next Free Address register Page Address and Device Select registers Control register after reset (including CT15) Persistent Destination for Command writes Persistent Source for Command reads Persistent Source and Destination for Data reads and writes Operating Mode Configuration Register set /RESET Condition Skip = 0, Empty = 1 (empty) Enabled Not Translated 64 bits CAM, 0 bits RAM Disabled Disabled 0B to 1B; loaded with 0B Contain all 0s Contain all 0s (no change on Software reset) Contains 0008H Instruction decoder Status register Comparand register Standard Foreground Table 5: Device Control State after Reset contained in the Address register. After the execution of the instruction, the Address register will increment, decrement, or stay the same value depending on the setting of Control Register bits CT3 and CT2. Control Register (CT) The Control register is composed of a number of switches that configure the WidePort LANCAM, as shown in Table 9. It is written or read through DQ15–0 using a TCO CT instruction on DQ31–16. On read cycles, DQ31–16 will be the upper 16 bits of the Status register. If bit 15 of the value written during a TCO CT is a 0, the device is reset (and all other bits are ignored). See Table 5 for the Reset states. Bit 15 always reads back as a 0. A write to the Control register causes an automatic compare to occur (except in the case of a reset). Either the Foreground or Background Control register will be active, depending on which register set has been selected, and only the active Control register will be written to or read from. If the Match flag is disabled through bits 14 and 13, the internal match condition, /MA(int), used to determine a daisy-chained device’s response is forced HIGH as shown in Tables 6a and 6b, so that Case 6 is not possible, effectively removing the device from the daisy chain. With the Match flag disabled, /MF=/MI and operations directed to Highest-priority Match locations are ignored. Normal operation of the device is with the /MF enabled. The Match Flag Enable field has no effect on the /MA or /MM output pins or Status Register bits. These bits always reflect the true state of the device. If the Full Flag is disabled through bits 12 and 11, the device behaves as if it were full and ignores instructions to Next Free address. Additionally, writes to the Page Address register will be disabled. All other instructions operate normally. Additionally, with the /FF disabled, /FF=/FI. Normal operation of the device is with the /FF enabled. The Full Flag Enable field has no effect on the /FL Status Register bit. This bit always reflects the true state of the device. The IEEE Translation control at bits 10 and 9 can be used to enable the translation hardware for writes to 64-bit resources in the device. When translation is enabled, the bits are reordered as shown in Figure 2. Control Register bits 8–6 control the CAM/RAM partitioning. The CAM portion of each word may be sized from a full 64 bits down to 16 bits in 16-bit increments. The RAM portion can be at either end of the 64-bit word. Compare masks may be selected by bits 5 and 4. Mask Register 1, Mask Register 2, or neither may be selected to mask compare operations. The address register behavior is controlled by bits 3 and 2, and may be set to increment, decrement, or neither after a memory access. Bits 1 and 0 set the operating mode: Standard (compatible with the MU9C1485) as shown in Table 6a, or Enhanced as shown in Table 6b. The device will reset to the Standard mode and follow the operating responses in Table 6a. When operating DQ 3 1 DQ 2 4 DQ 2 3 DQ 1 6 DQ 1 5 DQ 8 DQ 7 DQ 0 DQ 3 1 DQ 2 4 DQ 2 3 DQ 1 6 DQ 1 5 DQ 8 DQ 7 DQ 0 Figure 2: IEEE 802.3/802.5 Format Mapping 9 Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued in Enhanced mode, it is not necessary to unlock the daisy chain with a NOP instruction before command or data writes after a non-matching compare, as required in Standard mode. Segment Control Register (SC) The Segment Control register, as shown in Table 10, is accessed using a TCO SC instruction with the register contents placed on DQ15–0. On read cycles, DQ31–16 will be the upper 16 bits of the Status register, and D15, D10, D5, and D2 always read back as 0s. Reserved locations D14, D12, D9, D7, D4, and D1 should always be set to 0 and as such will also read back as 0s. Either the Foreground or Background Segment Control register will be active, depending on which register set has been selected, and only the active Segment Control register will be written to or read from. The Segment Control register contains dual independent incrementing counters with limits, one for data reads and one for data writes. These counters control which 32-bit segment of the 64-bit internal resource is accessed during a particular data cycle on the 32-bit data bus. The actual destination for data writes and source for data reads (called the persistent destination and source) are set independently with SPD and SPS instructions, respectively. Each of the two counters consists of a start limit, an end limit, and the current segment pointer, each a single bit representing either the lower segment (0) or the upper segment (1). The current segment pointer can be set to either 0 or 1 even if that value is outside the range set by the start and end segments. The counters count up from the current segment pointer to the end limit and then roll over back to the start limit. If a sequence of data writes or reads is interrupted, the Segment Control register can be reset to its initial start limit values with the RSC instruction. After a reset, both Source and Destination counters are set to count from Segment 0 to Segment 1 with an initial value of 0. Page Address Register (PA) The Page Address register is loaded using a TCO PA instruction on DQ31–16 with a user selected 16-bit value (not FFFFH) on DQ15–0. During reads of the PA register, DQ31–16 will all be 0. The entry in the PA register is used to give a unique address to the different devices in a daisy chain. In a daisy chain, the PA value of each device is loaded using the SFF instruction to advance to the next device, as shown in the “Setting Page Address Register Values” section. A software reset (using the Control register) does not affect the Page Address register. Device Select Register (DS) The Device Select register is used to select a specific (target) device using the TCO DS instruction in DQ31–16 and setting the 16-bit DS value in DQ15–0 equal to the target’s PA value. The DS register can be read through DQ15–0 with DQ31–16 returning the upper 16 bits of the Status register. In a daisy chain, setting DS = FFFFH will select all devices. However, in this case, the ability to read information out of the device is restricted as shown in Tables 6a and 6b. A software reset (using the Control register) does not affect the Device Select register. Address Register (AR) The Address register points to the CAM memory location to be operated upon when a M@[AR] or M@aaaH is part of the instruction. It can be loaded directly by using a TCO AR instruction or indirectly by using an instruction requiring an absolute address, such as MOV aaaH, CR,V. The AR register can be read through DQ15–0 with DQ31–16 returning the upper 16 bits of the Status register. After being loaded, the Address register value will then be used for the next memory access referencing the Address register. A reset sets the Address register to zero. Control Register bits CT3 and CT2 set the address to automatically increment or decrement (or not change) during sequences of Command or Data cycles. The Address register will change after executing an introduction that includes M@[AR] or M@aaaH, or after a data access to the end limit segment (as set in the Segment Control register) when the persistent source or destination is M@[AR] or M@aaaH. Either the Foreground or Background Address register will be active, depending on which register set has been selected, and only the active Address register will be written to or read from. Next Free Address Register (NF) The WidePort LANCAM automatically stores the address of the first empty memory location in the Next Free Address register, which is then used as a memory address pointer for M@NF operations. The Next Free Address register, shown in Table 11, can be read through DQ15–0 using a TCO NF instruction. DQ31–16 will return the upper 16 bits of the Status register. By taking /EC LOW during the TCO NF instruction cycle, only the device with /FI LOW and /FF HIGH will output the contents of its Next Free Address register, which gives the Next Free address in a system of daisy-chained devices. The Next Free address may be read from a specific device in the chain by setting the Device Rev. 2 10 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued Case Internal /EC(int) 1 1 1 0 0 0 Internal /MA (int) X X X X 1 0 External /MI X X X 0 1 1 Device Select Reg. DS=FFFFH DS=PA DS≠FFFFH and DS≠PA 4 5 6 2 Command Data Write Write1 YES3 YES NO NO NO YES 3 3 Command Read NO YES NO NO5 NO5 Data Read 1 2 3 YES4 YES NO NO NO YES 4 4 NO YES NO NO NO YES X X X YES 5 Table 6a: Standard Mode Device Select Response Case Internal /EC(int) 1 1 1 0 0 0 Internal /MA (int) X X X 0 1 0 External /MI X X X 0 X 1 Device Select Reg. DS = FFFFH DS = PA DS ≠ FFFFH and DS ≠ PA X X X Command Data Write Write1 YES3 YES3 NO YES3,6 YES 3,6 3 Command Read NO YES NO NO5 NO5 YES 5 Data Read 1 2 3 4 5 6 2 YES4 YES4 NO YES4,7 YES 4,7 4 NO YES NO NO NO YES YES YES NOTES: 1. Exceptions are: A) A write to the Device Select register is always active in all devices; B) A write to the Page Address register is active in the device with /FI LOW and /FF HIGH; and C) The Set Full Flag (SFF) instruction is active in the device with /FI LOW and /FF HIGH. 2. If /MF is disabled in the Control register, /MA (Internal) is forced HIGH preventing a Case 6 response. 3. This is NO for a MOV instruction involving Memory at Next Free address if /FI is HIGH or the device is full. 4. This is NO if the Persistent Destination is Memory at Next Free address and /FI is HIGH or the device is full. 5. For a Command Read following a TCO NF instruction, this is YES if the device contains the first empty location in a daisy chain (for example, /FI LOW and /FF HIGH) and NO if it does not. 6. This is NO for a MOV or VBC instruction involving Memory at Highest-Priority match. 7. This is NO if the Persistent Destination is Memory at Highest-Priority match. Table 6b: Enhanced Mode Device Select Response Select register to the value of the desired device’s Page address and leaving /EC HIGH. The Full Flag daisy chain causes only the device whose /FI input is LOW and /FF output HIGH to respond to an instruction using the Next Free address. After a reset, the Next Free Address register is set to zero. Status Register The 32-bit Status register, shown in Table 12, is the default source for Command Read cycles. Bit 31 is the internal Match flag, which will go LOW if a match was found in this particular device. Bit 30 is the internal Multiple Match flag, which will go LOW if a Multiple match was detected. Bit 29 is the internal Full flag, which will go LOW if the particular device has no 11 empty memory locations. Bits 28 and 27 are the Skip and Empty Validity bits, which reflect the validity of the last memory location read. After a reset, the Skip and Empty bits will read 11 until a read or move from memory has occurred. The rest of the Status register contains the Page address of the device and the address of the Highest-Priority match. After a reset or a no-match condition, the match address bits will be all 1s. Comparand Register (CR) The 64-bit Comparand register is the default destination for data writes and reads, using the Segment Control register to select which of the two 32-bit segments of the Comparand register is to be loaded or read out. The persistent source and destination for data writes and reads can be changed to the mask registers or memory by SPS and SPD Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued instructions. During an automatic or forced compare, the Comparand register is simultaneously compared against the CAM portion of all memory locations with the correct validity condition. Automatic compares always compare against valid memory locations, while forced compares, using CMP instructions, can compare against memory locations tagged with any specific validity condition. The Comparand register may be shifted one bit at a time to the right or left by issuing a Shift Right or Shift Left instruction, with the right and left limits for the wrap-around determined by the CAM/RAM partitioning set in the Control register. During shift rights, bits shifted off the LSB of the CAM partition will reappear at the MSB of the CAM partition. Likewise, bits shifted off the MSB of the CAM partition will reappear at the LSB during shift lefts. Mask Registers (MR1, MR2) The Mask registers can be used in two different ways, either to mask compares or to mask data writes and moves. Either mask register can be selected in the Control register to mask every compare, or selected by instructions to participate in data writes or moves to and from Memory. If a bit in the selected mask register is set to a 0, the corresponding bit in the Comparand register will enter into a masked compare operation. If a Mask bit is a 1, the corresponding bit in the Comparand register will not enter into a masked compare operation. Bits set to 0 in the mask register cause corresponding bits in the destination register or memory location to be updated when masking data writes or moves, while a bit set to 1 will prevent that bit in the destination from being changed. Either the Foreground or Background MR1 can be set active, but after a reset, the Foreground MR1 is active by default. MR2 incorporates a sliding mask, where the data can be replicated one bit at a time to the right or left with no wrap-around by issuing a Shift Right or Shift Left instruction. The right and left limits are determined by the CAM/RAM partitioning set in the Control register. For a Shift Right the upper limit bit is replicated to the next lower bit, while for a Shift Left the lower limit bit is replicated to the next higher bit. THE MEMORY ARRAY Memory Organization The Memory array is organized into 64-bit words with each word having an additional two validity bits (Skip and Empty). By default, all words are configured to be 64 CAM cells. However, bits 8–6 of the Control register can divide each word into a CAM field and a RAM field. The RAM field can be assigned to the least-significant or mostsignificant portion of each entry. The CAM/RAM partitioning is allowed on 16-bit boundaries, permitting selection of the configurations shown in Table 9, bits 8–6 (e.g., “001” sets the 48 MSBs to CAM and the 16 LSBs to RAM). Memory Array bits designated as RAM can be used to store and retrieve data associated with the CAM content at the same memory location. Memory Access There are two general ways to get data into and out of the memory array: directly or by moving the data through the Comparand or mask registers. The first way, through direct reads or writes, is set up by issuing a Set Persistent Destination (SPD) or Set Persistent Source (SPS) command. The addresses for the direct access can be directly supplied, supplied from the Address register, supplied from the Next Free Address register, or supplied as the Highest-Priority Match address. Additionally, all the direct writes can be masked by either mask register. The second way is to move data via the Comparand or mask registers. This is accomplished by issuing Data Move commands (MOV). Moves using the Comparand register can also be masked by either of the mask registers. I/O CYCLES The WidePort LANCAM supports four basic I/O cycles: Data Read, Data Write, Command Read, and Command Write. The type of cycle is determined by the states of the /W and /CM control inputs. These signals are registered at the beginning of a cycle by the falling edge of /E. Table 3 shows how the /W and /CM lines select the cycle type and how the data bus is utilized for each. During Read cycles, the DQ31–0 outputs are enabled after /E goes LOW. During Write cycles, the data or command to be written is captured from DQ31–0 at the beginning of the cycle by the falling edge of /E. Figures 3 and 4 show Read and Write cycles respectively. Figure 5 shows typical cycle-to-cycle timing with the Match flag valid at the end Rev. 2 12 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued /E /W /CM /E C DQ 1 5– 0 DATA O UT Figure 3: Read Cycle /E /W /CM DQ 1 5 – 0 Figure 4: Write Cycle COM P AR AN D W RIT E C YC L E /E S TA TU S R EAD C YC L E ASS OC IAT E D D ATA R EA D C YCL E /CM /W DQ3 1 – 0 DA TA DA TA DA TA /EC /M F M AT CH FLA G V A LI D /M A, /M M /M F FL A GS U P D A TE D Figure 5: Cycle to Cycle Timing Example of the Comparand Write cycle, assuming /EC is LOW at the start of this cycle. Data writes and reads to the comparand, mask registers or memory occur in one or two 32-bit cycles, depending on the settings in the Segment Control register. The Compare operation automatically occurs during Data writes to the Comparand or mask registers when the destination segment counter reaches the end count set in the Segment Control register. If there was a match, the second cycle reads status or associated data, depending on the state of /CM. For cascaded devices, /EC needs to be LOW at the start of the cycle prior to any cycle that requires a locked daisy chain, such as a Status register or associated data read after a match. If there is no match in Standard mode, the output buffers stay HIGH-Z, and the daisy chain must be unlocked by taking /EC HIGH during a NOP or other non-functioning cycle, as indicated in Table 6a. 13 Figure 6 shows how the internal /EC timing holds the daisy chain locking effect over into the next cycle. In the Enhanced mode, this NOP is not needed before data or command writes following a non-matching compare, as indicated by Table 6b. A single-chip system does not require daisychained match flag operation, hence /EC could be tied HIGH and the /MA pin or flag in the Status register used instead of /MF, allowing access to the device regardless of the match condition. The minimum timings for the /E control signal are given in the Switching Characteristics section. Note that at minimum timings the /E signal is non-symmetrical, and that different cycle types have different timing requirements, as given in Table 8. Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued /E /EC /EC (INT ) /MF To operate the daisy chain, the Device Select registers are set to FFFFH to enable all devices to execute Command Write and Data Write cycles. In normal operation, read cycles are enabled from the device with the highest-priority match by locking the daisy chain (see “Locked Daisy Chain” section). An individual device in the chain may be targeted for a read or write operation by temporarily setting the Device Select registers to the page address of the target device. Setting the Device Select registers back to FFFFH restores the operation of the entire daisy chain. Match Flag Cascading The Match Flag daisy chain cascading is used for three purposes: first, to allow operations on Highest-priority Match addresses to be issued globally over the whole string; second, to provide a system wide match flag; third, to lock out all devices except the one with the Highest-Priority match for instructions such as Status reads after a match. The Match flag logic causes only the highest-priority device to operate on its Highest-priority Match location while devices with lower-priority matches ignore Highest-priority Match operations. The lock-out feature is enabled by the match flag cascading and the use of the /EC control signal, as shown in Tables 6a and 6b. The ripple delay of the flags when connected in a daisy chain may require the extension of the /E HIGH time until the logic in all devices has settled out. In a string of “n” devices, the /E HIGH time should be greater than: tEHMFV + (n-2)· tMIVMFV If the last device’s Match flag is required by external logic or a state machine before the start of the next CAM cycle, one additional tMIVMFV should be added to the /E HIGH time along any required setup time and delays for the external logic. Locked Daisy Chain In a locked daisy chain, the highest-priority device is the one with /MI HIGH and /MF LOW. In Standard mode, only this device will respond to command and data reads and writes, until the daisy chain has been unlocked by taking /EC HIGH. This allows reading the associated data field from only the Highest-Priority Match location anywhere in a string of devices, or the Match address from the Status register of the device with the match. It also permits updating the entry stored at the Highest-Priority Match location. In Enhanced mode, devices are enabled to respond to some command and data writes, as noted in Tables 6a and 6b, but not command and data reads. 14 Figure 6: /EC(Int) Timing Diagram COMPARE OPERATIONS During a Compare operation, the data in the Comparand register is compared to all locations in the Memory array simultaneously. Any mask register used during compares must be selected beforehand in the Control register. There are two ways compares are initiated: Automatic and Forced compares. Automatic compares perform a compare of the contents of the Comparand register against Memory locations that are tagged as “Valid,” and occur whenever the following happens: Ø The Destination Segment counter in the Segment Ø Control register reaches its end limit during writes to the Comparand or mask registers. After a command write of a TCO CT is executed (except for a software reset), so that a compare is executed with the new settings of the Control register. Forced compares are initiated by CMP instructions using one of the four validity conditions, V, R, S, and E. The forced compare against “Empty” locations automatically masks all 64 bits of data to find all locations with the validity bits set to “Empty”, while the other forced compares are only masked as selected in the Control register. VERTICAL CASCADING WidePort LANCAMs can be vertically cascaded to increase system depth. Through the use of flag daisychaining, multiple devices will respond as an integrated system. The flag daisy chain allows all commands to be issued globally, with a response only in the device containing the Highest-Priority Matching or Next Free location. When connected in a daisy chain, the last device’s Full flag and Match flag accurately report the condition for the whole string. A system in which WidePort LANCAMs are vertically cascaded using daisy-chaining of the flags is shown in Figure 1a. Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued Table 6a (Standard mode) and Table 6b (Enhanced mode) show when a device will respond to reads or writes and when it will not, based on the state of /EC(int), the internal match condition, and other control inputs. /EC is latched by the falling edge of /E. /EC(int) is registered from the latched /EC signal off the rising edge of /E, so it controls what happens in the next cycle, as shown in Figure 6. When /EC is first taken LOW in a string of LANCAM devices (and assuming the Device Select registers are set to FFFFH), all devices will respond to that command write or data write. From then on the daisy chain will remain locked in each subsequent cycle as long as /EC is held LOW on the falling edge of /E in the current cycle. When the daisy chain is locked in Standard mode, only the Highest-Priority Match device will respond (See Case 6 of Table 6a). If, for example, all of the CAM memory locations were empty, there would be no match, and /MF would stay HIGH. Since none of the devices could then be the Highest-Priority Match device, none will respond to reads or writes until the daisy chain is unlocked by taking /EC HIGH and asserting /E for a cycle. If there is a match between the data in the Comparand register and one or more locations in memory, then only the Highest-Priority Match device will respond to any cycle, such as an associated data or Status Register read. If there is not a match, then a NOP with /EC HIGH needs to be inserted before issuing any new instructions, such as Write to Next Free Address instruction to learn the data. Since Next Free operations are controlled by the /FI–/FF daisy chain, only the device with the first empty location will respond. If an instruction is used to unlock the daisy chain it will work only on the Highest-Priority Match device, if one exists. If none exists, the instruction will have no effect except to unlock the daisy chain. To read the Status registers of specific devices when there is no match requires the use of the TCO DS command to set DS=PA of each device. Single chip systems can tie /EC HIGH and read the Status register or the /MA and /MM pins to monitor match conditions, as the daisy chain lock-out feature is not needed in this configuration. This removes the need to insert a NOP in the case of a no-match. When the Control register is set to Enhanced mode, you can continue to write data to the Comparand register or issue a Move to Next Free Address instruction without first having to issue a NOP with /EC HIGH to unlock the daisy chain after a Compare cycle with no match, as indicated in cases 4 and 5 of Table 6b. In Enhanced mode, data write cycles as well as command write cycles are enabled in all devices even when /EC is LOW. Exceptions are data writes, moves, or VBC instructions involving HM, 15 which occur only in the device with the highest match; and data writes or move instructions involving NF, which occur only in the device with /FI LOW and /FF HIGH. Enhanced mode speeds up system performance by eliminating the need to unlock the daisy chain before Command or Data Write cycles. Full Flag Cascading The Full Flag daisy chain cascading is used for three purposes: first, to allow instructions that address Next Free locations to operate globally; second, to provide a system wide Full flag; third, to allow the loading of the Page Address registers during initialization using the SFF instruction. The full flag logic causes only the device containing the first empty location to respond to Next Free instructions such as “MOV NF,CR,V”, which will move the contents of the Comparand register to the first empty location in a string of devices and set that location Valid, so it will be available for the next automatic compare. With devices connected as in Figure 1a, the /FF output of the last device in a string provides a full indication for the entire string. IEEE 802.3/802.5 Format Mapping To support the symmetrical mapping between the address formats of IEEE 802.3 and IEEE 802.5, the WidePort LANCAM provides a bit translation facility. Formally expressed, the nth input bit, D(n), maps to the xth output bit, Q(x), through the following expressions: D(n) = Q(7-n) for 0 ≤ n ≤ 7, D(n) = Q(23-n) for 8 ≤ n ≤ 15 D(n) = Q(39-n) for 16 ≤ n ≤ 23 D(n) = Q(55-n) for 24 ≤ n ≤ 31 Control Register bits CT10 and CT9 select whether to persistently translate, or persistently not to translate, the data written onto the 64-bit internal bus. The default condition after a Reset command is not to translate the incoming data. Figure 2 shows the bit mapping between the two formats. INITIALIZING THE WIDEPORT LANCAM Initialization of the WidePort LANCAM is required to configure the various registers on the device. Since a Control register reset establishes the operating conditions shown in Table 5, restoration of operating conditions better suited for the application may be required after a reset, whether using the Control Register reset, or the /RESET pin. When the device powers up, the memory and registers are in an unknown state, so the /RESET pin must be asserted to place the device in a known state. Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued Setting Page Address Register Values In a vertically cascaded system, the user must set the individual Page Address registers to unique values by using the Page Address initialization mechanism. Each Page Address register must contain a unique value to prevent bus contention. This process allows individual device selection. The Page Address register initialization works as follows: Writes to Page Address registers are only active for devices with /FI LOW and /FF HIGH. At initialization, all devices are empty, thus the top device in the string will respond to a TCO PA instruction, and load its PA register. To advance to the next device in the string, a Set Full Flag (SFF) instruction is used, which is also only active for the device with /FI LOW and /FF HIGH. The SFF instruction changes the first device’s /FF to LOW, although the device really is empty, which allows the next device in the string to respond to the TCO PA instruction and load its PA register. The initialization proceeds through the chain in a similar manner filling all the PA registers in turn. Each device must have a unique Page Address value stored in its PA register, or contention will result. After all the PA registers are filled, the entire string is reset through the Control register, which does not change the values stored in the individual PA registers. After the reset, the Device Select registers are usually set to FFFFH to enable operation, in Case 1 of Table 6a. The Control registers and the Segment Control registers are then set to their normal operating values for the application. Vertically Cascaded System Initialization Table 7 shows an example of code that initializes a daisychained string of WidePort LANCAM devices. The initialization example shows how to set the Page Address registers of each of the devices in the chain through the use of the Set Full Flag instruction, and how the Control registers and Segment counters of all the WidePort LANCAM devices are set for a typical application. Each Page Address register must contain a unique value (not FFFFH) to prevent bus contention. For typical daisy chain operation, data is loaded into the Comparand registers of all the devices in a string simultaneously by setting DS=FFFFH. Since reading is prohibited when DS=FFFFH except for the device with a match, for a diagnostic operation you need to select a specific device by setting DS=PA for the desired device to be able to read from it. Refer to Tables 6a and 6b for preconditions for reading and writing. Initialization for a single WidePort LANCAM is similar. The Device Select register in this case is usually set to equal the Page Address register for normal operations. Also, the dedicated /MA flag output can be used instead of /MF, allowing /EC to be tied HIGH. Cycle Type Command Write Command Write Command Write Command Write Op-Code TCO DS TCO CT TCO PA SFF • • TCO CT TCO CT TCO SC Data Bus DQ31–16 0A28H 0A00H 0A08H 0700H DQ15–0 FFFFH 0000H nnnnH X Comments Target Device Select register and disable local device selection Target Control register and reset Target Page Address register and set page for cascaded operation Set Full flag; allows access to next device (repeat previous cycle plus this one for each device in chain) Target Control register and reset Full flags, but not Page address Target Control register and give initial values Target Segment counter and set destination to only use upper segment and source to only use lower segment Set Persistent source to Memory at the Highest-Priority match Notes 1 2 2 Command Write Command Write Command Write 0A00H 0A00H 0A10H 0005H 0000H 8080H 2808H X 3 Command Write SPS M@HM Notes: 4 1. Toggling the /RESET pin generates the same effect as this reset of the Control register, but good programming practice dictates a software reset for initialization to account for all possible prior conditions. 2. This instruction may be omitted for a single WidePort LANCAM application. The last SFF will cause the /FF pin in the last chip in a daisy chain to go LOW. In a daisy chain, DS needs to be set equal to PA to read out a particular chip prior to a match condition. 3. Typical WidePort LANCAM control environment: Enable match flag; Enable full flag; 32 CAM bits/32 RAM bits; Disable comparison masking; and Enable address increment. This example translates to 8080H. See Table 9 for Control Register bit assignments. 4. Setting the persistent source to the Memory at Highest-Priority match allows a compare operation to be followed by a read of the associated data when a match is found. Note that the persistent destination is set to the Comparand register by the reset. Table 7: Example Initialization Routine Rev. 2 16 WidePort LANCAM® Family INSTRUCTION SET DESCRIPTIONS § Instruction: Select Persistent Source (SPS) Binary Op-Code: 0000 f000 0000 0sss* f Address Field flag† sss Selected source This instruction selects a persistent source for data reads, until another SPS instruction changes it or a reset occurs. The default source after reset for Data Read cycles is the Comparand register. Setting the persistent source to M@aaaH loads the Address register with “aaaH,” and the first access to that persistent source will be at aaaH, after which the AR value increments or decrements as set in the Control register. The SPS M@[AR] instruction does the same except the current Address Register value is used. Instruction: Select Persistent Destination (SPD) Binary Op-Code: 0000 f001 mmdd dvvv* f Address Field flag† mm Mask Register select ddd Selected destination vvv Validity setting for Memory Location destinations This instruction selects a persistent destination for data writes, which remains until another SPD instruction changes it or a reset occurs. The default destination for Data Write cycles is the Comparand register after a reset. When the destination is the Comparand register or the memory array, the data written may be masked by either Mask Register 1 or Mask Register 2, so that only destination bits corresponding to bits in the mask register set to 0 will be modified. An automatic compare will occur after writing the last segment of the Comparand or mask registers, but not after writing to memory. Setting the persistent destination to M@aaaH loads the Address register with “aaaH,” and the first access to that persistent destination will be at aaaH, after which the AR value increments or decrements as set in the Control register. The SPD M@[AR] instruction does the same except the current Address Register value is used. Instruction: Temporary Command Override (TCO) Binary Op-Code: 0000 f010 00dd d000* f Address Field flag† ddd Register selected as source or destination for only the next Command Read or Write cycle The TCO instruction temporarily redirects the DQ bus for register access. If f=1, a register write will be performed with the data on DQ15–0. If f=0, a subsequent Command Read cycle reads the register contents through DQ15–0. During register reads, DQ31–16 will contain the upper 16bits of the Status register, except in the case of a Page 17 Address register read where these bits are 0s. After the access, subsequent Command Read or Write cycles revert to reading the Status register and writing to the Instruction decoder. All registers except the Status, NF, PS, and PD are available for write access. All registers are available for read access. The complete Status register is only available through a non-TCO Command Read access. Reading the PS register also outputs the Device ID on bits 15–4, as shown in Table 13. Instruction: Data Move (MOV) Binary Op-Code: 0000 f011 mmdd dsss or 0000 f011 mmdd dvss* f Address Field flag† mm Mask Register select ddd Destination of data sss Source of data v Validity setting if destination is a Memory location The MOV instruction performs a 64-bit move of the data in the selected source to the selected destination. If the source or destination is aaaH, the Address register is set to “aaaH.” For MOV instructions to or from aaaH or [AR], the Address register will increment or decrement from that value after the move completes, as set in the Control register. Data transfers between the Memory array and the Comparand register may be masked by either Mask Register 1 or Mask Register 2, in which case, only those bits in the destination which correspond to bits in the selected mask register set to 0 will be changed. A Memory location used as a destination for a MOV instruction may be set to Valid or left unchanged. If the source and destination are the same register, no net change occurs (a NOP). Instruction: Validity Bit Control (VBC) Binary Op-Code: 0000 f100 00dd dvvv* f Address Field flag† ddd Destination of data vvv Validity setting for Memory location The VBC instruction sets the Validity bits at the selected memory locations to the selected state. This feature can be used to find all valid entries by using a repetitive sequence of CMP V through a mask of all 1s followed by a VBC HM, S. If the VBC target is aaaH, the Address register is set to “aaaH.” For VBC instructions to or from aaaH or [AR], the Address register will increment or decrement from that value after the operation completes, as set in the Control register. Rev. 2 WidePort LANCAM® Family INSTRUCTION SET DESCRIPTIONS C ontinued Instruction: Compare (CMP) Binary Op-Code: 0000 0101 0000 0vvv* vvv Validity condition A CMP V, S, or R instruction forces a Comparison of Valid, Skipped, or Random entries against the Comparand register through a mask register, if one is selected. During a CMP E instruction, the compare is only done on the Validity bits and all data bits are automatically masked. Instruction: Special Instructions Binary Op-Code: 0000 0110 00dd drrr* ddd Target resource rrr Operation These instructions are a special set for the A/L WidePort LANCAMs to accommodate the added features over the MU9C1485. Two alternate sets of configuration registers can be selected by using the Select Foreground and Select Background Registers instructions. These registers are the Control, Segment Control, Address, Mask Register 1, and the PS and PD registers. An RSC instruction resets the Segment Control register count values for both the Destination and Source counters to the original Start limits. The Shift instructions shift the designated register one bit right or left. The right and left limits for shifting are determined by the CAM/RAM partitioning set in the Control register. The Comparand register is a barrel-shifter, and for the example of a device set to 64 bits of CAM executing a Shift Comparand Right instruction, bit 0 is moved to bit 63, bit 1 is moved to bit 0, and bit 63 is moved to bit 62. For a Shift Comparand Left instruction, bit 63 is moved to bit 0, bit 0 is moved to bit 1, and bit 62 is moved to bit 63. MR2 acts as a sliding mask, where for a Shift Right instruction bit 1 is moved to bit 0, while bit 0 “falls off the end,” and bit 63 is replicated to bit 62. For a Shift Mask Left instruction, bit 0 is replicated to bit 1, bit 62 is moved to bit 63, and bit 63 "falls off the end.” With shorter width CAM fields, the bit limits on the right or left move to match the width of CAM field. Instruction: Set Full Flag (SFF) Binary Op-Code: 0000 0111 0000 0000* The SFF instruction is a special instruction used to force the Full flag LOW to permit setting the Page Address register in vertically cascaded systems. Instruction: No Operation (NOP) Binary Op-Code: 0000 0011 0000 0000 The NOP (No-OP) belongs to the MOV instructions, where a register is moved to itself. No change occurs within the device. This instruction is useful in unlocking the daisy chain in Standard mode. Notes: § Instruction cycle lengths given in Table 8. * Instruction Op-Codes are loaded on the DQ31–16 lines. † If f=1, the instruction requires an absolute address (or register contents for TCOs) to be supplied onthe DQ15–0 lines. Supplied addresses will update the Address register to the “aaaH” value supplied. After an operation involving M@[AR] or M@aaaH, the Address register will be incremented or decremented depending on the setting in the Control register. Rev. 2 18 WidePort LANCAM® Family INSTRUCTION SET SUMMARY MNEMONIC FORMAT INS dst,src[msk],val INS: Instruction mnemonic dst: Destination of the data src: Source of the data msk: Mask register used val: Validity condition set at the location written Instruction: Select Persistent Destination Cont. Operation Mnemonic Op-Code Mem. at Highest-Prio. Match, Emp. SPD M@HM,E Masked by MR1 SPD M@HM[MR1],E Masked by MR2 SPD M@HM[MR2],E Mem. at Highest-Prio. Match, Skip SPD M@HM,S Masked by MR1 SPD M@HM[MR1],S Masked by MR2 SPD M@HM[MR2],S Mem. at High.-Prio. Match, Random SPD M@HM,R Masked by MR1 SPD M@HM[MR1],R Masked by MR2 SPD M@HM[MR2],R Mem. at Next Free Addr., Valid SPD M@NF,V Masked by MR1 SPD M@NF[MR1],V Masked by MR2 SPD M@NF[MR2],V Mem. at Next Free Addr., Empty SPD M@NF,E Masked by MR1 SPD M@NF[MR1],E Masked by MR2 SPD M@NF[MR2],E Mem. at Next Free Addr., Skip Masked by MR1 Masked by MR2 SPD M@NF,S SPD M@NF[MR1],S SPD M@NF[MR2],S 012DH 016DH 01ADH 012EH 016EH 01AEH 012FH 016FH 01AFH 0134H 0174H 01B4H 0135H 0175H 01B5H 0136H 0176H 01B6H 0137H 0177H 01B7H Instruction: Select Persistent Source Operation Mnemonic Comparand Register Mask Register 1 Mask Register 2 Memory Array at Addr. Reg. Memory Array at Address Mem. at Highest-Prio. Match SPS CR SPS MR1 SPS MR2 SPS M@[AR] SPS M@aaaH SPS M@HM Op-Code 0000H 0001H 0002H 0004H 0804H 0005H Instruction: Select Persistent Destination Operation Mnemonic Op-Code Comparand Register Masked by MR1 Masked by MR2 Mask Register 1 MaskRegister 2 Mem. at Addr. Reg. set Valid Masked by MR1 Masked by MR2 Mem. at Addr. Reg. set Empty Masked by MR1 Masked by MR2 Mem. at Addr. Reg. set Skip Masked by MR1 Masked by MR2 SPD CR SPD CR[MR1] SPD CR[MR2] SPD MR1 SPD MR2 SPD M@[AR],V SPD M@[AR][MR1],V SPD M@[AR][MR2],V SPD M@[AR],E SPD M@[AR][MR1],E SPD M@[AR][MR2],E SPD M@[AR],S SPD M@[AR][MR1],S SPD M@[AR][MR2],S 0100H 0140H 0180H 0108H 0110H 0124H 0164H 01A4H 0125H 0165H 01A5H 0126H 0166H 01A6H 0127H 0167H 01A7H 0924H 0964H 09A4H 0925H 0965H 09A5H 0926H 0966H 09A6H 0927H 0967H 09A7H 012CH 016CH 01ACH Mem. at Next Free Addr., Random SPD M@NF,R Masked by MR1 SPD M@NF[MR1],R Masked by MR2 SPD M@NF[MR2],R Instruction: Temporary Command Override Operation Mnemonic Op-Code Control Register Page Address Register Segment Control Register Read Next Free Address Address Register Device Select Register Read Persistent Source Read Persistent Destination TCO CT TCO PA TCO SC TCO NF TCO AR TCO DS TCO PS TCO PD 0n00H* 0n08H* 0n10H * 0218H 0n20H * 0n28H * 0230H 0238H Mem. at Addr. Reg. set Random SPD M@[AR],R Masked by MR1 SPD M@[AR][MR1],R Masked by MR2 SPD M@[AR][MR2],R Memory at Address set Valid Masked by MR1 Masked by MR2 Memory at Addr. set Empty Masked by MR1 Masked by MR2 Memory at Address set Skip Masked by MR1 Masked by MR2 Mem. at Address set Random Masked by MR1 Masked by MR2 SPD M@aaaH,V SPD M@aaaH[MR1],V SPD M@aaaH[MR2],V SPD M@aaaH,E SPD M@aaaH[MR1],E SPD M@aaaH[MR2],E SPD M@aaaH,S SPD M@aaaH[MR1],S SPD M@aaaH[MR2],S SPD M@aaaH,R SPD M@aaaH[MR1],R SPD M@aaaH[MR2],R *Note: n = 2 for register read access n = A for register write access Instruction: Data Move Operation Comparand Register from: No Operation Mask Register 1 Mask Register 2 Memory at Address Reg. Masked by MR1 Masked by MR2 Memory at Address Masked by MR1 Masked by MR2 Mnemonic NOP MOV CR,MR1 MOV CR,MR2 MOV CR,[AR] MOV CR,[AR][MR1] MOV CR,[AR][MR2] MOV CR,aaaH MOV CR,aaaH[MR1] MOV CR,aaaH[MR2] Op-Code 0300H 0301H 0302H 0304H 0344H 0384H 0B04H 0B44H 0B84H 0305H 0345H 0385H Mem. at Highest-Prio. Match, Valid SPD M@HM,V Masked by MR1 SPD M@HM[MR1],V Masked by MR2 SPD M@HM[MR2],V Mem. at Highest-Prio. Match MOV CR,HM Masked by MR1 MOV CR,HM[MR1] Masked by MR2 MOV CR,HM[MR2] 19 Rev. 2 WidePort LANCAM® Family INSTRUCTION SET SUMMARY Continued Instruction: Data Move Continued Operation Mnemonic Mask Register 1 from: Comparand Register No Operation Mask Register 2 Memory at Address Reg. Memory at Address Mem. at Highest-Prio. Match Mask Register 2 from: Comparand Register Mask Register 1 No Operation Memory at Address Reg. Memory at Address Mem. at Highest-Prio. Match MOV MR1,CR NOP MOV MR1,MR2 MOV MR1,[AR] MOV MR1,aaaH MOV MR1,HM Op-Code 0308H 0309H 030AH 030CH 0B0CH 030DH Memory at Next Free Address, Comparand Register Masked by MR1 Masked by MR2 Mask Register 1 Mask Register 2 Memory at Next Free Address, Comparand Register Masked by MR1 Masked by MR2 Mask Register 1 Mask Register 2 No Change to Validity bits, from: MOV NF,CR 0330H MOV NF,CR[MR1] 0370H MOV NF,CR[MR2] 03B0H MOV NF,MR1 0331H MOV NF,MR2 0332H Location set Valid, from: MOV NF,CR,V MOV NF,CR[MR1],V MOV NF,CR[MR2],V MOV NF,MR1,V MOV NF,MR2,V MOV MR2,CR MOV MR2,MR1 NOP MOV MR2,[AR] MOV MR2,aaaH MOV MR2,HM 0310H 0311H 0312H 0314H 0B14H 0315H 0334H 0374H 03B4H 0335H 0336H Instruction: Validity Bit Control Operation Mnemonic Set Validity bits at Address Register Set Valid VBC [AR],V Set Empty VBC [AR],E Set Skip VBC [AR],S Set Random Access VBC [AR],R Set Validity bits at Address Set Valid Set Empty Set Skip Set Random Access Op-Code 0424H 0425H 0426H 0427H Memory at Address Register, No Change to Validity bits, from: Comparand Register MOV [AR],CR 0320H Masked by MR1 MOV [AR],CR[MR1] 0360H Masked by MR2 MOV [AR],CR[MR2] 03A0H Mask Register 1 MOV [AR],MR1 0321H Mask Register 2 MOV [AR],MR2 0322H Memory at Address Register, Location set Valid, from: Comparand Register MOV [AR],CR,V Masked by MR1 MOV [AR],CR[MR1],V Masked by MR2 MOV [AR],CR[MR2],V Mask Register 1 MOV [AR],MR1,V Mask Register 2 MOV [AR],MR2,V Memory at Address, No Change to Validity bits, from: Comparand Register MOV aaaH,CR Masked by MR1 MOV aaaH,CR[MR1] Masked by MR2 MOV aaaH,CR[MR2] Mask Register 1 MOV aaaH,MR1 Mask Register 2 MOV aaaH,MR2 Memory at Address, Location set Valid, from: Comparand Register MOV aaaH,CR,V Masked by MR1 MOV aaaH,CR[MR1],V Masked by MR2 MOV aaaH,CR[MR2],V Mask Register 1 MOV aaaH,MR1,V Mask Register 2 MOV aaaH,MR2,V Memory at Highest-Priority Match, No Change to Validity from: Comparand Register MOV HM,CR Masked by MR1 MOV HM,CR[MR1] Masked by MR2 MOV HM,CR[MR2] Mask Register 1 MOV HM,MR1 Mask Register 2 MOV HM,MR2 0324H 0364H 03A4H 0325H 0326H VBC aaaH,V VBC aaaH,E VBC aaaH,S VBC aaaH,R 0C24H 0C25H 0C26H 0C27H 0B20H 0B60H 0BA0H 0B21H 0B22H Set Validity bits at Highest-Priority Match Set Valid VBC HM,V Set Empty VBC HM,E Set Skip VBC HM,S Set Random Access VBC HM,R Set Validity bits at All Matching Set Valid Set Empty Set Skip Set Random Access Locations VBC ALM,V VBC ALM,E VBC ALM,S VBC ALM,R 042CH 042DH 042EH 042FH 043CH 043DH 043EH 043FH 0B24H 0B64H 0BA4H 0B25H 0B26H bits, 0328H 0368H 03A8H 0329H 032AH Instruction: Compare Operation Compare Valid Locations Compare Empty Locations Compare Skipped Locations Comp. Random Access Locations Mnemonic CMP V CMP E CMP S CMP R Op-Code 0504H 0505H 0506H 0507H Instruction: Special Instructions Operation Mnemonic Shift Comparand Right Shift Comparand Left Shift Mask Register 2 Right Shift Mask Register 2 Left Select Foreground Registers Select Background Registers Reset Seg. Cont. Reg. to Initial Val. SFT CR, R SFT CR, L SFT M2, R SFT M2, L SFR SBR RSC Op-Code 0600H 0601H 0610H 0611H 0618H 0619H 061AH Memory at Highest-Priority Match, Location set Valid, from: Comparand Register MOV HM,CR,V 032CH Masked by MR1 MOV HM,CR[MR1],V 036CH Masked by MR2 MOV HM,CR[MR2],V 03ACH Mask Register 1 MOV HM,MR1,V 032DH Mask Register 2 MOV HM,MR2,V 032EH Instruction: Miscellaneous Instructions Operation Mnemonic No Operation Set Full Flag NOP SFF Op-Code 0300H 0700H Rev. 2 20 WidePort LANCAM® Family INSTRUCTION SET SUMMARY Continued CYCLE LENGTH Short Command Write MOV reg, reg (except L-70) TCO reg (except CT) TCO CT (non-reset, HMA invalid) SPS, SPD, SFR SBR, RSC, NOP SFT (A) MOV reg, reg (L-70) MOV reg, mem TCO CT (reset) VBC (NFA invalid) SFT (L) MOV mem, reg TCO CT (non-reset, HMA valid) CMP SFF VBC (NFA valid) Status register or 16-bit register CYCLE TYPE Command Read Data Write Comparand register (not last segment) Mask register (not last segment) Data Read Medium Memory array (NFA invalid) Comparand register Mask register Memory array Long Memory array (NFA valid) Comparand register (last segment) Mask register (last segment) Note: The specific timing requirements for Short, Medium, and Long cycles are given in the Switching Characteristics Section under the tELEH parameter. For two cycle TCO reads of a register’s contents, the first cycle (Command Write TCO) is short, and the second cycle (Command read) is medium. Table 8: Instruction Cycle Lengths REGISTER BIT ASSIGNMENTS 15 RST R E S E T = 0 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Mode Match Flag Enable =00 Disable = 01 No Change = 11 Full Flag Translation Enable = 00 Disable = 01 No Change = 11 Input Not Translated = 00 Input Translated = 01 No Change = 11 CAM/RAM Part. 64 CAM/0 RAM = 000 48 CAM/16 RAM = 001 32 CAM/32 RAM = 010 16 CAM/48 RAM = 011 48 RAM/16 CAM = 100 32 RAM/32 CAM = 101 16 RAM/48 CAM = 110 No Change = 111 Comp. Mask AR Inc/Dec None = 00 MR1 = 01 MR2 = 10 No Change = 11 Increment = 00 Decrement = 01 Disable = 10 No Change = 11 Standard Mode = 00 Enhanced Mode = 01 Reserved = 10 No Change = 11 Note: D15 reads back as 0. Table 9: Control Register Bit Assignments 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 Set Dest. Seg. Limits =0 No Chng. =1 Reserved Dest. Count Start Limit 0 Dest. Set Count Source End Seg. Limit Limits =0 No Chng. =1 Reserved 0 Reserved Src. Count Start Limit 0 Reserved Src. Count End Limit Load Dest. Seg. Count =0 No Chng. =1 0 Dest. Load Seg. Src. Count Seg. Value Count =0 No Chng. =1 Reserved 0 Reserved Src. Seg. Count Value Note: D15, D10, D5, and D2 read back as 0s. Reserved locations D14, D12, D9, D7, D4, and D1 should always be set to 0. Table 10: Segment Control Register Bit Assignments 21 Rev. 2 WidePort LANCAM® Family REGISTER BIT ASSIGNMENTS Continued 31 4485A/L 2485A/L 1485A/L 4485A/L 2485A/L 1485A/L /MA /MA /MA 15 30 /MM /MM /MM 14 29 /FL /FL /FL 13 28 27 26 25 24 23 22 21 20 19 18 17 16 Skip Empty Skip Empty Skip Empty 12 11 0 10 9 8 7 Page Address Bits, PA14–4 Page Address Bits, PA15–5 Page Address Bits, PA15–6 6 5 4 3 2 1 0 Next Free Address, NF11–0 Next Free Address, NF10–0 Page Address, PA3–0 Page Address, PA4–0 Page Address, PA5–0 Next Free Address, NF9–0 Note: The Next Free Address register is read only, and is accessed by performing a Command Read cycle immediately following a TCO NF instruction. Table 11: Next Free Address Register Bit Assignments 31 4485A/L 2485A/L 1485A/L 4485A/L 2485A/L 1485A/L /MA /MA /MA 15 30 /MM /MM /MM 14 29 /FL /FL /FL 13 28 27 26 25 24 23 22 21 20 19 18 17 16 Skip Empty Skip Empty Skip Empty 0 12 11 10 9 8 Page Address Bits, PA14–4 Page Address Bits, PA15–5 Page Address Bits, PA15–6 7 6 5 3 2 4 Match Address, AM11–0 Match Address, AM10–0 Match Address, AM9–0 1 0 Page Address, PA3–0 Page Address, PA4–0 Page Address, PA5–0 Note: The Status register is read only, and is accessed by performing a Command Read cycle. Table 12: Status Register Bit Assignments 31 4485A/L 2485A/L 1485A/L 4485A/L 2485A/L 1485A/L Note: 30 /MM /MM /MM 14 29 /FL /FL /FL 13 28 27 26 25 24 23 22 21 20 19 18 17 16 /MA /MA /MA 15 Skip Empty Skip Empty Skip Empty 12 11 0 10 9 8 Page Address Bits, PA14–4 Page Address Bits, PA15–5 Page Address Bits, PA15–6 2 7 6 5 4 3 1 PS PS PS 0 Device ID = 445 H Device ID = 245 H Device ID = 145 H The Persistent Source register is read only, and is accessed by performing a Command Read cycle immediately following a TCO PS instruction. Table 13: Persistent Source Register Bit Assignments Rev. 2 22 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Supply Voltage Voltage on all other pins Temperature under bias Storage Temperature DC Output Current “A” Devices “L” Devices -0.5 to 7.0 Volts -0.5 to 4.6 Volts -0.5 to VCC +0.5 Volts (-2 Volts for 10 ns, measured at the 50% point) -55°C to 125°C -55°C to 125°C 20 mA (per output, one at a time, one second duration. Stresses exceeding those listed under Absolute Maximum Ratings may include failure. Exposure to absolute maximum ratings for extended periods may reduce reliability. Functionality at or above these conditions is not implied. All voltages referenced to GND. OPERATING CONDITIONS (voltages referenced to GND at the device pin) Symbol Parameter VCC Operating Supply Voltage VIH VIL TA Input Voltage Logic 1 Min Typical “A” Devices 4.75 “L” Devices 3.0 2.0 5.0 3.3 Max 5.25 3.6 Units Volts Volts 1, 2 Still Air Notes -0.5 Input Voltage Logic 0 Ambient Operating Commercial (-XXTCC) 0 Temperature Industrial (-XXTCI) -40 VCC + 0.5 Volts 0.8 Volts 70 85 °C °C DC ELECTRICAL CHARACTERISTICS Average Power Supply Current (mA) -50 Device 1485A 1485L 2485A 2485L 4485A 4485L Typ 290 n/a 355 n/a 490 n/a Max 335 n/a 395 n/a 525 n/a -70 -90 Max 235 170 275 185 350 235 -12 Typ 175 120 200 135 265 180 Max 200 150 225 165 295 205 Typ Max Typ 240 155 285 175 375 230 265 215 185 145 325 450 205 165 400 330 265 215 Symbol Parameter ICC(SB) Stand-by Power Supply Current VOH VOL IIZ Output Voltage Logic 1 Output Voltage Logic 0 Input Leakage Current /RESET TEST1, TEST2 Others IOZ Output Leakage Current “A” Devices “L” Devices Min Typical Max 7 2 Units mA mA Volts Notes /E = HIGH IOH = -2.0mA IOL = 4.0mA 2.4 0.4 6 6 -2 -10 9 10 15 15 +2 10 Volts Kohms VIN = 0 V Kohms VIN=Vcc; 11 µA µA VSS ≤ VIN ≤ VCC VSS ≤ VOUT ≤ VCC; DQN = High Impedance 23 Rev. 2 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued CAPACITANCE Symbol Parameter CIN COUT Input Capacitance Output Capacitance Max 6 7 Units pF pF Notes f = 1 MHz, VIN = 0 V f = 1 MHz, VOUT = 0 V AC TEST CONDITIONS Input Signal Transitions Input Signal Rise Time Input Signal Fall Time Input Timing Reference Level Output Timing Reference Level 0.0 Volts to 3.0 Volts < 3 ns < 3 ns 1.5 Volts 1.5 Volts SWITCHING TEST FIGURES Vc c R1 I nput Waveform T o D evice U nder T est C1 R2 0V V IL (MIN) 50% Amplitude Point Figure 6: AC Test Load 10ns Figure 7: Input Signal Waveform SWITCHING TEST FIGURE COMPONENT VALUES Parameter VCC R1 R2 C1 (Includes jig) “A” Devices 5.0 961 510 30 5 “L” Devices 3.3 635 702 30 5 Units Volts Ohm Ohm pF pF Test Load A Test Load B Rev. 2 24 WidePort LANCAM® Family OPERATIONAL CHARACTERISTICS Continued SWITCHING CHARACTERISTICS (see Note 3) Available N/A Not Available No 1 2 · Cycle Time “A” Devices “L” Devices -50 N/A Min 50 15 30 45 5 0 10 3 30 40 3 0 10 0 5 35 0 0 4 16 18 50 0 0 10 3 0 10 0 Max 70 15 35 55 15 0 10 3 · -70 Symbol Parameter (all times in nanoseconds) tELEL Chip Enable Compare Cycle Time tELEH Chip Enable LOW Short Cycle: Pulse Width Medium Cycle: Long Cycle: Min Max Min 90 25 50 75 15 0 10 3 30 52 10 3 0 10 0 5 50 0 0 5 16 18 100 100 · · -90 · · -12 Max Min 120 35 75 100 20 0 15 3 · · Max Notes 4 4 4 5 5 6 70 85 4,6 4,6 7 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 tEHEL tCVEL tELCX tELQX tELQV tEHQZ tDVEL tELDX tFIVEL Chip Enable HIGH Pulse Width Control Input to Chip Enable LOW Set-up Time Control Input from Chip Enable LOW Hold Time Chip Enable LOW to Outputs Active Chip Enable LOW to Outputs Valid Chip Enable HIGH to Outputs High-Z Data to Chip Enable LOW Set-up Time Data from Chip Enable LOW Hold Time Full In Valid to Chip Enable LOW 50 75 15 3 0 15 0 7 75 0 0 7 25 25 100 20 Set-up Time tFIVFFV Full In Valid to Full Flag Valid tELFFV Chip Enable LOW to Full Flag Valid tMIVEL Match In Valid to Chip Enable LOW Set-up Time tEHMFX Chip Enable HIGH to /MF, /MA, /MM Invalid tMIVMFV Match In Valid to /MF Valid tEHMFV Chip Enable HIGH to /MF Valid tEHMXV Chip Enable HIGH to /MA and /MM Valid tRLRH Reset LOW Pulse Width 8 90 8 30 30 8 Notes: 1. -1.0V for a duration of 10 ns measured at the 50% amplitude points for Input-only lines (Figure 8). 2. Common I/O lines are clamped, so that signal transients cannot fall below -0.5V. 3. Over Ambient Operating Temperature and Vcc(min) to Vcc(max). 4. See Table 8. 5. Control signals are /W, /CM, and /EC. 6. With load specified in Figure 7, Test Load A. 7. With load specified in Figure 7, Test Load B. 8. /E must be HIGH during this period to ensure accurate default values in the configuration registers. 9. With output and I/O pins unloaded. 10. TEST1 and TEST2 may not be implemented on all versions of these products. 25 Rev. 2 WidePort LANCAM® Family TIMING DIAGRAMS READ CYCLE WRITE CYCLE 2 3 2 3 /E /E 4 5 4 5 /W /W 4 5 4 5 /C M / CM /EC 4 5 4 /EC 5 9 10 DQ1 5 – 0 7 8 11 D Q 15–0 / FI 6 13 / FF 12 COMPARE CYCLE 1 2 /E 3 4 5 /W 4 5 V AL ID /CM 4 5 /EC 14 /M I 15 16 /M F 17 /M A, /M M 18 Rev. 2 26 WidePort LANCAM® Family PACKAGE OUTLINE He E A2 A1 Hd D G a ge Plan e 0 .2 5 L1 L L e b c Dimensions are in mm. Dim. A1 Dim. A2 80-pin TQFP 0.05 0.15 1.35 1.45 Dim. b 0.22 0.38 Dim. c 0.08 0.20 Dim. D 13.90 14.10 Dim. E 13.90 14.10 Dim. e 0.65 nom Dim. Hd 15.90 16.10 Dim.He 15.90 16.10 Dim. L 0.45 0.75 Dim. L1 1.00 nom 27 Rev. 2 WidePort LANCAM® Family ORDERING INFORMATION Part Number MU9C4485A - 50TCC MU9C4485A - 70TCC MU9C4485A - 90TCC MU9C4485A - 12TCC MU9C4485L - 70TCC MU9C4485L - 90TCC MU9C4485L - 12TCC MU9C4485A - 70TCI MU9C4485A - 90TCI MU9C4485A - 12TCI MU9C2485A - 50TCC MU9C2485A - 70TCC MU9C2485A - 90TCC MU9C2485A - 12TCC MU9C2485L - 70TCC MU9C2485L - 90TCC MU9C2485L - 12TCC MU9C2485A - 70TCI MU9C2485A - 90TCI MU9C2485A - 12TCI MU9C1485A - 50TCC MU9C1485A - 70TCC MU9C1485A - 90TCC MU9C1485A - 12TCC MU9C1485L - 70TCC MU9C1485L - 90TCC MU9C1485L - 12TCC MU9C1485A - 70TCI MU9C1485A - 90TCI MU9C1485A - 12TCI Organization 4096 x 64 4096 x 64 4096 x 64 4096 x 64 4096 x 64 4096 x 64 4096 x 64 4096 x 64 4096 x 64 4096 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 2048 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 1024 x 64 Cycle Time 50ns 70ns 90ns 120ns 70ns 90ns 120ns 70ns 90ns 120ns 50ns 70ns 90ns 120ns 70ns 90ns 120ns 70ns 90ns 120ns 50ns 70ns 90ns 120ns 70ns 90ns 120ns 70ns 90ns 120ns Package 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP 80-PIN TQFP Temperature 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C -40–85° C -40–85° C -40–85° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C -40–85° C -40–85° C -40–85° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C 0–70° C -40–85° C -40–85° C -40–85° C Voltage 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 3.3 ± 0.3 3.3 ± 0.3 3.3 ± 0.3 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 3.3 ± 0.3 3.3 ± 0.3 3.3 ± 0.3 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 5.0 ± .25 3.3 ± 0.3 3.3 ± 0.3 3.3 ± 0.3 5.0 ± .25 5.0 ± .25 5.0 ± .25 MUSIC Semiconductors Agent or Distributor: MUSIC Semiconductors reserves the right to make changes to its products and specifications at any time in order to improve on performance, manufacturability, or reliability. Information furnished by MUSIC is believed to be accurate, but no responsibility is assumed by MUSIC Semiconductors for the use of said information, nor for any infringement of patents or of other third party rights which may result from said use. No license is granted by implication or otherwise under any patent or patent rights of any MUSIC company. ©Copyright 1998, MUSIC Semiconductors Asian Headquarters MUSIC Semiconductors Special Export Processing Zone 1 Carmelray Industrial Park Canlubang, Calamba, Laguna Philippines Tel: +63 49 549 1480 Fax: +63 49 549 1024 Sales Tel/Fax: +632 723 62 15 European Headquarters MUSIC Semiconductors Torenstraat 28 6471 JX Eygelshoven Netherlands Tel: +31 45 5462177 Fax: +31 45 5463663 USA Headquarters MUSIC Semiconductors, Inc. 254 B Mountain Avenue Hackettstown, New Jersey 07840 USA http://www.music-ic.com Tel: 908/979-1010 email: info@music-ic.com Fax: 908/979-1035 USA Only: 800/933-1550 Tech Support 888/226-6874 Product Info Rev. 2 28