Conductive Polymer Aluminum
Solid Capacitors
P9
OS-CON Line-up
Selection guide
Technical data
P15 Series system diagram
P16 Image of case size
P17 Products list
P21 Packing specifications（SMD type）
P23 Packing specifications（Radial lead type）
P25 Recommended soldering condition
P26 Fundamental structure
P27 Characteristics
P30 Reliability
P33 SXV
Surface mount type
P34 SVPG
P35 SVPF
P37 SVPE
P39 SVPS
P41 SVPD
P43 SVPC
P45 SVPB
P47 SVPA
P49 SVQP
P51 SVP
Radial lead type
Conductive Polymer Aluminum Solid Capacitors
P11 Guidelines and precautions
P53 SXE
P54 SEPF
P55 SEPC
P57 SEQP
P59 SEP
P61 Catalog Deletion and EOL series
※ Yelloew letters ： Update
※ Red letters ： New series
INDEX
P8
OS-CON INDEX
P9
OS-CON Line-up
P11 Guidelines and precautions
P15 Selection guide
P25 Technical data
P33 Each series
P61 Catalog Deletion and EOL series
8
Guidelines and precautions for use
About capacitors
Please take note of the following points in order to make the best use of capacitor's
performance.
Please use capacitors within the range of specified performance after confirming
each capacitor's usage environment and circuit condition.
Please choose capacitors that match the lifetime of the intended circuit design.
The performance of capacitors is changed by the temperature or frequency.
Therefore, please consider these variations when designing the circuit.
Please buy capacitors from our official distributors. Otherwise there is no warranty.
Line-up
Conductive Polymer Aluminum Solid Capacitors
Conductive Polymer Tantalum Solid Capacitors
Considerations when using in
industrial equipment
To when capacitors are used in industrial equipment,
allow wider margin of capacitance, impedance and other
characteristics.
Polarity
OS-CON and POSCAP have polarity.
Please confirm the polarity prior to use. If it is used with
the reverse polarities, leakage current, shorter lifetime or
a short circuit may result.
There is no bi-polar model of the OS-CON and POSCAP.
Rating and category
The definition of rating and category is as follows.
Rated temperature:
The maximum ambient temperature at which rated
voltage may be continuously applied.
Operating temperature and
ripple current
Rated voltage:
The maximum direct voltage or peak value of pulse
voltage which may be applied continuously to a
capacitor at any temperature between the lower
category temperature and the rated temperature.
Set the operating temperature so that it falls within the
The range of ambient temperatures for which a capacitor
Do not apply current that exceeds the allowable ripple
has been designed to operate continuously;
current. When excessive ripple current is applied,
this is given by the lower and upper category
internal heat increases and reduces the lifetime.
temperature.
In case capacitors are used under the condition out of
Category voltage:
the specified frequency, ripple current shall not exceed
the value revised by the frequency coefficient.
5
Category temperature range:
range stipulated in this delivery specification.
The maximum voltage which may be applied continuously
to a capacitor at its upper limit of category temperature.
Parallel connection
Operating environment restrictions
Ripple current may be flowed to a capacitor that has
Do not use the capacitor in the following environments
lower impedance when a different kind of capacitor is
used in parallel.
Please be very careful of choosing models.
Please consider the balance of electric current when
more than two capacitors are connected in parallel.
Places where water, salt water or oil can directly fall on
it and pleces where dew condensation may form
Places with noxious gas (hydrogen sulfide, sulfurous
acid, nitrous acid, chlorine, ammonia, etc)
Places susceptible to ozone, ultraviolet rays and radiation
Places where vibration or shock exceeds the allowable
value as specified in the catalog or specification sheet
Places under direct sunlight
Applied voltage for designing
Do not apply voltages exceeding the full rated voltage.
If such voltage is applied, it may cause short circuit
even though it is just a moment.
90% and below of the rated voltage or category
voltage of the POSCAP is recommended. If the
rated voltage is 10V or over except for TQC series,
80% and below of the rated voltage or category
voltage is recommended.
The sum of the DC voltage plus the peak AC voltage
shall not exceed the rated voltage or category voltage.
The sum of the DC voltage plus the negative peak
AC voltage shall not allow reverse voltage.
Do not apply reverse voltage.
Please contact us when there is a concern that circuit
operation may cause reverse voltage.
Land pattern
Please design hole space and hole diameter of circuit
board for capacitor radial lead type,
or land patterns for capacitor SMD type with
consideration of the product dimension specified in the
catalog or specification sheet and the size tolerance.
Avoid locating heat-generating components around the
capacitor and on the underside of the PC board.
When a capacitor is mounted to the double sided circuit
board, avoid placing through holes under the capacitor.
Avoid having the printed wire under the capacitor.
Soldering
The soldering conditions as soldering iron, flow soldering, reflow soldering should be under the range prescribed in specifications.
If the specifications are not followed, there is a possibility of the cosmetic defection, the intensive increase of leakage
current or the capacitance reduction.
Soldering heat stress to capacitor varies depending on temperature, duration time, mounting condition such as size,
material and component quantity of PC board. Please check the heat durability in your actual soldering condition.
6
Guidelines and precautions for use
About capacitors
Things to be noted before
mounting
Do not reuse capacitors that have been assembled in a
set and energized.
Leakage current may increase when capacitors are
stored for long term. In this case, we recommend you to
apply the rated voltage for 1 hour at 60℃ to 70℃ with
a resistor load of 1kΩ.
In case the capacitor has re-striking-voltage, please
apply the rated voltage to the capacitor through a
resistor load of 1kΩ.
Storage conditions
It is necessary to maintain a good storage environment
in order to prevent the problem when soldering due to
the degradation of solderability or moisturization of
molding resin.
When storing the reel in the storage bag, please
ensure that the storage bag is fully sealed.※
Do not store in high temperature and high humidity
environment.
For duration of storage, refer to the respective
"Guidelines and precautions for use" of each capacitor.
Do not store in damp conditions such as with water,
salt water, or oil, and dew condensation.
Do not store in places filled with noxious gas
Mounting 1
Please mount capacitors after confirming the polarity.
Please mount capacitors after confirming its rated
capacitance and rated voltage.
When mounting capacitors to the circuit board, please
use capacitors with the lead space matching the hole
space of the circuit board.
Do not drop capacitors or use capacitors dropped
beforehand.
(hydrogen sulfide, sulfurous acid, nitrous acid,
chlorine, ammonia, etc).
Do not store in places susceptible to ozone, ultraviolet
rays and radiation.
Please unseal storage bag just before mounting and
be conscious that the capacitors are used up.
Refer to the respective "Guidelines and precautions
for use" of each capacitor when some remain by
necessity.
※Only for capacitors packed by laminate bag.
Be careful not to deform the capacitor during installation.
Mounting 2
When an automatic inserter is used to clinch the
Capacitors comprise solid organic compounds, various
capacitor lead terminal, make sure it is not set too
metals, resin, rubber, etc. Treat them as industrial waste
strongly.
when disposing of it.
Be careful of the shock force that can be produced by
In case of disposing of a large amount of capacitor, we
absorbers, product chckers and centers on automatic
inserters and installers.
Do not apply excessive external force to the lead
terminal or the capacitor itself.
7
Disposal of capacitors
can dispose on your behalf.
OS-CON
Line-up
Fundamental
structure
Characteristics
Reliability
Classification
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Series
Page
Features
SXV
33
Super high voltage
105℃ 5,000ｈ
SVPG
34
Low ESR
High ripple current
SVPF
35 to 36
SVQP
SVPE
SVP
Radial lead type
SXE
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
●
●
High voltage
Large capacitance
●
105℃ 5,000h
Super low ESR
●
● ●
● ●
Large capacitance
Size
code
Category
temperature
range(℃)
SVPS
SVPD
39 to 40
41 to 42
Guaranteed at 125℃
Rated 35V max.
85℃85％ RH
● ●
15 to 33
B45 −55 to ＋105 16 to 25
15 to 47
C10 −55 to ＋105
Selection guide
SVPC
43 to 44
SVPB
SVPA
SVQP
45 to 46
47 to 48
49 to 50
Low profile
Low ESR
High ripple current
Guaranteed at 125℃
Surface mount type
SVP
51 to 52
Standard
−55 to ＋105 16 to 25
27 to 82
C6
−55 to ＋105 16 to 50
10 to 180
E7
−55 to ＋105 16 to 50
18 to 270
E12 −55 to ＋105 16 to 50
39 to 560
F12 −55 to ＋105 16 to 50
68 to 1,000
B6
−55 to ＋105 2.5 to 6.3
150 to 390
C6
−55 to ＋105 2.5 to 10
220 to 390
16
● ●
9
Purple
Purple
Purple
Purple
470
10 to 33
A5
−55 to ＋105 4.0 to 10
B6
−55 to ＋105 4.0 to 16
22 to 68
C6
−55 to ＋105 4.0 to 20
22 to 150
E7
−55 to ＋105 4.0 to 25
10 to 270
F8
−55 to ＋105 4.0 to 16
100 to 680
C6
−55 to ＋125 10 to 25
10 to 56
E7
−55 to ＋125 16 to 35
8.2 to 82
F8
−55 to ＋125 25 to 35
18 to 39
E12 −55 to ＋125 25 to 35
22 to 47
Purple
Purple
47 to 82
B6
−55 to ＋105 2.5 to 16
39 to 180
C6
−55 to ＋105 2.5 to 16
68 to 560
E7
−55 to ＋105 2.5 to 16
120 to 680
Purple
E12 −55 to ＋105 2.5 to 16 270 to 1,500
C5
●
C55 −55 to ＋105
●
●
2.5
−55 to ＋105 2.5 to 20
20
2,700
15 to 120
22
B6
−55 to ＋105 2.5 to 20
10 to 82
C6
−55 to ＋105 2.5 to 20
22 to 180
E7
−55 to ＋105 2.5 to 20
47 to 330
F8
−55 to ＋105 2.5 to 16
180 to 820
C6
−55 to ＋125 4.0 to 20
22 to 150
E7
−55 to ＋125 6.3 to 20
47 to 220
A5
−55 to ＋105 4.0 to 16
3.3 to 33
B6
−55 to ＋105 4.0 to 20
10 to 68
C6
−55 to ＋105 2.5 to 20
22 to 220
E7
−55 to ＋105 4.0 to 20
33 to 330
F8
−55 to ＋105 4.0 to 20
E12 −55 to ＋105 2.5 to 20
Catalog Deletion and
EOL models
270
B6
F12 −55 to ＋105
Technical data
16
F12 −55 to ＋125 25 to 35
Low ESR
Large capacitance
Capacitance Marking
range(μＦ)
color
C10 −55 to ＋105 2.0 to 1.6 180 to 1,200
●
Long life
Rated
voltage
range
(Ｖ．ＤＣ)
E12 −55 to ＋105 63 to 100
F12 −55 to ＋105
Surface mount type
SEPF
37 to 38
Long life ・ High reliability
Recommended
soldering
condition
High voltage
Packing
specifications
（Radial lead type）
Low ESR
Packing
specifications
（SMD type）
Large capacitance
Products list
Line-up
Small size ・ Low profile
Image of
case size
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
56 to 680
100 to 680
F12 −55 to ＋105 2.5 to 20 150 to 1,500
Purple
Purple
Purple
Purple
OS-CON
Line-up
54
Small size・Low profile
High voltage
Large capacitance
105℃ 5,000h
E12 −55 to ＋105 63 to 100
15 to 33
C55 −55 to ＋105 16 to 32
22 to 150
C6
●
●
● ●
Radial lead type
SEPC
55 to 56
● ● ●
●
−55 to ＋105 16 to 35
−55 to ＋105 16 to 35
39 to 270
82 to 560
F13 −55 to ＋105 16 to 35
120 to 1,000
E7
Purple
−55 to ＋105
2.5
100 to 560
Ｃ55 −55 to ＋105
6.3
220
Purple
100 to 560
C6
−55 to ＋105 2.5 to 16
C7
−55 to ＋105
C9
−55 to ＋105 2.5 to 16
E7
−55 to ＋105 2.5 to 16 150 to 1,000 Purple
E9
−55 to ＋105 2.5 to 16 180 to 1,000
E12 −55 to ＋105
6.3
16
E13 −55 to ＋105 2.5 to 6.3
57 to 58
105℃ 5,000h
Guaranteed at 125℃
Rated 32V max.
● ●
59 to 60
Standard
Fundamental
structure
Characteristics
Reliability
SXV
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVP
180 to 270
470 to 820
C6
−55 to ＋125 4.0 to 20
22 to 150
E7
−55 to ＋125 4.0 to 32
6.8 to 330
F8
−55 to ＋125 4.0 to 32
15 to 680
E12 −55 to ＋125 4.0 to 32
18 to 560
C6
−55 to ＋105 4.0 to 20
22 to 150
E7
−55 to ＋105 4.0 to 20
33 to 330
F8
−55 to ＋105 4.0 to 20
56 to 680
E12 −55 to ＋105 2.5 to 20
Recommended
soldering
condition
470
100 to 820
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Purple
POSCAP
Line-up
Guidelines and
precautions
F13 −55 to ＋125 4.0 to 20 150 to 1,200
SEP
Packing
specifications
（Radial lead type）
SVQP
F13 −55 to ＋105 2.5 to 16 470 to 2,700
SEQP
Products list
Packing
specifications
（SMD type）
SVPG
22 to 180
E12 −55 to ＋105 16 to 35
B9
Super low ESR
Large capacitance
Small size
Low profile
105℃ 5,000h
Selection guide
Long life ・ High reliability
High voltage
●
Capacitance Marking
range(μＦ)
color
Technical data
Super high voltage
105℃ 5,000ｈ
Size
code
Rated
voltage
range
(Ｖ．ＤＣ)
Image of
case size
Surface mount type
SEPF
53
Features
Category
temperature
range(℃)
Series system
diagram
Radial lead type
SXE
Page
Low ESR
Series
Large capacitance
Classification
Small size ・ Low profile
Guidelines and
precautions
Selection guide
Purple
100 to 680
F13 −55 to ＋105 2.5 to 20 150 to 1,500
Technical data
Surface mount type
Catalog Deletion and
EOL models
10
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Guidelines and
precautions
Precautions for circuit designing
C rucial precautions
Important
1.Prohibited circuits
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
（a）Leakage current of the OS-CON may increase in the following conditions.
（1）Soldering
（2）When voltage is not applied: high temperature no-load test, high temperature and high humidity no-load test,
rapidly changing temperature test, etc.
（b）Avoid the use of the OS-CON in the following type of circuits because leakage current may increase.
（1）High-impedance circuits
（2）Coupling circuits
（3）Time constant circuits
（4）Other circuits that are significantly affected by leakage current
SVP
※ If you plan to use 2 or more OS-CONs in a series connection, please contact us before use
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
2.Failure and life-span
The failure rate is 0.5% /1000h (Confidence level: 60%) based on JIS C 5003.
The prospective failure is not zero. The mainly failure modes are as follows.
2-1. Contingency failure
The most common failure mode is a short circuit. Mainly caused by the soldering or operating temperature
environment, along with heat stresses, electrical stresses or mechanical stressesas follows.
POSCAP
Line-up
Guidelines and
precautions
（1）Applying voltage over the rated voltage.
（2）Applying reverse voltage
（3）Excessive mechanical stress
（4）Applying rush current by sudden charge or discharge out of the specification.
（a）The following phenomenon is seen when short-current is applied to the OS-CON.
Selection guide
（1）When current is relatively low (φ10: approx 1A or less, φ8: approx 0.5A or less, φ6.3:approx 0.2A or
less)The OS-CON becomes heated, but no effects are visible even when the current is continously carried.
（2）When the short circuit currents exceed the mentioned value above.
After internal temperature increase, sealing rubber may be turned over.
In some cases, odorous gas may be produced.
Technical data
（b）In case a short circuit occurs, ensure safety by fully considering the followings.
（1）If odorous gas is released, turn off the main power of the equipment.
In this case, keep your face and hands away from the area.
（2）Though it depends on the conditions, it takes seconds to minutes before odorant gas generates.
Protective circuit should operate in this period.
（3）If the gas comes into eyes, rinse immediately. If the gas is inhaled, gargle immediately.
（4）Do not lick the electrolyte. If the electrolyte touches skin, wash it off with soap immediately.
（5）The OS-CON contains combustible substances. In case a large current continues to flow after a short
Surface mount type
circuit, in the worst case, the shorted-out section may ignite. For safety, install a redundant circuit or
a protective circuit, etc.
2-2. Wear-out failure (lifetime)
When lifetime span exceeded the specified guarantee time of endurance and damp heat, electrolyte might
insulate and cause electric characteristic changed. This is called an open circuit.
The electric characteristics of capacitance and ESR may possibly change within the specified range in
specifications even if it is used under the condition of the rated voltage,
Catalog Deletion and
EOL models
11
electric and mechanical performance. Please note it when designing.
OS-CON
Line-up
Selection guide
Guidelines and
precautions
Technical data
O ther precautions
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
1.Leakage current
SVPG
In such a case, leakage current will gradually decrease by applying voltage (withinthe category voltage and the
upper limit of category temperature).
Then, self-healing speed of leakage current is faster when it is near to the upper limit of category temperature and
the category voltage.
OS-CON
leakage current restoration characteristics
16V/10μF (16V DC applied)
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
(Measured voltage:10V)
100
10
60℃
1
20℃
105℃
1
10
100
1,000
100
5V applied
10
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
8V applied
1
10V applied
0.1
SXE
Radial lead type
1,000
Leakage current (μA)
Leakage current (μA)
leakage current restoration characteristics
SVPE
10V/33μF (Ambient temperature:65℃)
1,000
0.1
OS-CON
SVPF
Surface mount type
Mechanical stress may cause OS-CON’s leakage current increased.
1
(Hrs.)
10
100
POSCAP
Line-up
Guidelines and
precautions
1,000
(Hrs.)
※To make the recovery of LC values easy to
show, samples that LC values have been
increased on purpose are used in the test.
Selection guide
Technical data
2.Rapid charge and discharge limitation
Allowance of a large rush current to flow due to rapid charge and discharge may result in short circuit or large
leakage current. The protection circuit, to maintain high reliability, is recommended when rush current to flow
to the OS-CON is in the following cases.
（a）Products which 10 times of allowable ripple current is less than 10A: It is when 10A or over of rush current is applied
Surface mount type
（b）Products which 10 times of allowable ripple current is 10A or over: It is when rush current, which the figure is
over 10 times of allowable ripple current, is applied.
Catalog Deletion and
EOL models
12
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Guidelines and
precautions
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
3.Soldering with a soldering iron
6.Handling after soldering
(a) When lead terminals for radial lead type must
Do not subject the OS-CON to excessive stress as
be processed because the lead pitch and the PCB
follows.
holes do not match, process them without any
(a) Do not tilt, bend or twist the OS-CON.
stresses to the OS-CON before soldering.
(b) Do not move the PCB with holding the OS-CON
(b) Solder without any excessive stresses to the
OS-CON itself.
(c) When the OS-CON has been soldered once and
needs to be removed, remove it after the solder
SVQP
itself.
(c) Do not hit the OS-CON with objects.
(d) When stacking PCBs, make sure that the OS-CON
does not touch other PCBs or components.
has been completely melted.
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
(d) Do not let the tip of the soldering iron touch the
OS-CON itself.
7.Cleaning PCB
Check the following items before washing PC board
4.Flow soldering
with these detergents: high quality alcohol-based
(a) Do not apply flow soldering to OS-CON SMD type.
750H, 750L, 710M, 750K or Techno Care FRW 14
(b) Do not solder the OS-CON itself by submerging
it in melted solder.
Solder the opposite side that the OS-CON is
mounted on.
(c) Note that flux does not adhere to anywhere expect
Selection guide
the lead terminal.
(d) Note that other components do not fall over and
touch the OS-CON when soldering.
cleaning fluid such as Pine-α ST-100S, clean thru
through 17 or detergents including substitute
freon as AK-225AES or IPA.
(a) Use immersion or ultrasonic waves to clean
within 2 minutes.
(b) The temperature of the cleaning fluid should
be less than 60℃.
(c) Watch the contamination of the detergent
such as conductivity, pH, specific gravity,
water content, etc.
(d) Do not store the OS-CON in a location subject
Technical data
5.Reflow soldering
(a) Do not apply reflow soldering to OS-CON
Radial Lead type.
(b) Please contact us for setting VPS conditions.
to gases from the cleaning fluid or in an
airtight container after cleaning.
(e) Dry the PCB or OS-CON with hot air that should
be less than the upper category temperature.
(f) Please note that indication may disappear
when rubbing print side after washing
depending on a cleaner.
Surface mount type
(g) Please contact us for details about detergents,
cleaning methods and detergents other
than those listed above.
Catalog Deletion and
EOL models
13
OS-CON
Line-up
Technical data
Selection guide
Guidelines and
precautions
8.Fixatives and coating materials
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
9.Capacitor insulation
for the OS-CON. In particular, don’t use acetone
lead terminal, positive lead terminal and PC board
in the fixative, coating agent and diluent.
patterns with each other due to the following
（b）Before applying the fixative or coating, completely
reasons.
（a）Insulation is not guaranteed at a part of resin on
remove any flux residue and foreign matter from
the surface of a case.
the area where the board and the OS-CON will
（b）It offers inconstant resistance between a case
be jointed together.
SVPF
Surface mount type
Be sure to completely separate the case, negative
（a）Select the appropriate covering and sealant materials
SVPG
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
and a negative lead terminal and it isn’t insulated.
（c）Allow any detergent to dry before applying the
SVQP
fixative or coating.
SVP
curing conditions.
Open the bags just before mounting and use up all products once opened,
For keeping a good solderability, store the OS-CON as follows.
Before unsealing
Within 24 months after shipment
Bag packing product
Radial
lead type Taping product
Within 30 months after shipment
Within 24 months after shipment
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
10.Storage conditions
SMD type※1
SXE
Radial lead type
（d）Please contact us for the fixative and coating heat
POSCAP
Line-up
Guidelines and
precautions
After unsealing
Within 30 days from opening
(packaged with carrier tape)
Selection guide
Within 7 days from opening
※1 The JEDEC J-STD-020 standard is not applicable
Technical data
Surface mount type
Catalog Deletion and
EOL models
14
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
SXV
Series system
diagram
SMD type
P.51 to 52
SVP
Standard
F12 Size
2.5 to 25V
56 to 1,500μF
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
E12 Size
2.5 to 25V
33 to 680μF
F8 Size
4.0 to 25V
22 to 680μF
E7 Size
4.0 to 25V
10 to 330μF
C6 Size
SVQP
2.5 to 25V
6.8 to 220μF
SXE
B6 Size
Radial lead type
SVP
SEPF
SEPC
SEQP
SEP
4.0 to 20V
10 to 68μF
A5 Size
4.0 to 16V
3.3 to 33μF
Catalog Deletion and
EOL series
P.47 to 48
SVPA
Low ESR
High ripple current
F8 Size
2.5 to 16V
180 ∼ 820μF
E7 Size
2.5 to 20V
47 ∼ 330μF
C6 Size
2.5 to 20V
22 to 180μF
B6 Size
2.5 to 20V
10 to 82μF
P.45 to 46
SVPB
P.39 to 40
P.43 to 44
SVPC
Large capacitance
Low ESR
F12 Size
2.5V
2,700μF
P.35 to 36
SVPF
105℃5,000h
High voltage
Large capacitance
E12 Size
F12 Size
E7 Size
E12 Size
2.5 to 16V
270 to 1,500μF
2.5 to 16V
120 to 680μF
C6 Size
2.5 to 16V
68 to 560μF
B6 Size
2.5 to 16V
39 to 180μF
Low profile
16 to 50V
68 to 1,000μF
16 to 50V
39 to 560μF
P.37 to 38
SVPE
Super low ESR
Large capacitance
F12 Size
16V
470μF
C10 Size
2.0,16V
180,1200μF
C6 Size
E7 Size
2.5 to 10V
220, 390μF
C6 Size
2.5, 6.3V
150 to 390μF
16 to 50V
18 to 270μF
B6 Size
16 to 50V
10 to 180μF
SVPS SVQP
Long life
F8 Size
E7 Size
C6 Size
4.0 to 25V
10 to 270μF
C6 Size
4.0 to 20V
22 to 150μF
B6 Size
4.0 to 16V
22 to 68μF
A5 Size
4.0 to 10V
10 to 33μF
E12 Size
New
63 to 100V
15 to 33μF
4.0 to 20V
22 to 150μF
P.41 to 42
SVPD
Guaranteed at 125℃
High voltage
F12 Size
25, 35V
47, 82μF
E12 Size
E7 Size
16 to 35V
8.2 to 82μF
C6 Size
C10 Size
New
Guidelines and
precautions
105℃5,000h
Super high volltage
25, 35V
18, 39μF
Low ESR
High ripple current
POSCAP
Line-up
SXV
F8 Size
SVPG
2.5 to 20V
15 to 120μF
P.33
25, 35V
22, 47μF
P.34
C5 Size
E7 Size
6.3 to 20V
47 to 220μF
B6 Size
20V
22μF
Guaranteed at 125℃
4.0 to 16V
100 to 680μF
16 to 25V
27 to 82μF
C55 Size
P.49 to 50
10, 25V
10, 56μF
16V
270μF
B45 Size
New
16 to 25V
15 to 47μF
Selection guide
Radial lead type
P.59 to 60
Technical data
SEP
Standard
E12 Size
2.5 to 25V
33 to 680μF
E7 Size
4.0 to 25V
10 to 330μF
Surface mount type
F13 Size
2.5 to 25V
56 to 1,500μF
F8 Size
4.0 to 25V
22 to 680μF
C6 Size
Catalog Deletion and
EOL models
15
4.0 to 25V
6.8 to 150μF
SEPC
105℃5,000h
Super low ESR
Large capacitance
P.55 to 56
F13 Size
2.5 to 16V
470 to 2,700μF
E13 Size E12 Size
2.5 to 6.3V
470 to 820μF
16V
180, 270μF
E9 Size
E7 Size
C9 Size
C6 Size
2.5 to 16V
180 to 1,000μF
2.5 to 16V
100 to 820μF
2.5 to 16V
150 to 1,000μF
2.5, 16V
100 to 560μF
C55 Size C7 Size
6.3V
220μF
P.57 to 58
6.3V
470μF
B9 Size
2.5V
100 to 560μF
SEPF
105℃5,000h
High voltage
Large capacitance
P.54
F13 Size
16 to 35V
120 to 1,000μF
E12 Size E7 Size
16 to 35V
82 to 560μF
16 to 35V
39 to 270μF
C6 Size
C55 Size
16 to 35V
22 to 180μF
16, 32V
22, 150μF
SEQP F13
105℃ 5,000h
Guaranteed at 125℃
High voltage
Size
4.0 to 20V
150 to 1,200μF
E12 Size F8 Size
4.0 to 32V
18 to 560μF
E7 Size
4.0 to 32V
6.8 to 330μF
4.0 to 32V
15 to 680μF
C6 Size
4.0 to 20V
22 to 150μF
P.53
SXE
105℃5,000h
Super high volltage
E12 Size
New
63 to 100V
15 to 33μF
OS-CON
Line-up
Image of
case size
Selection guide
Guidelines and
precautions
SMD type
P.45 to 46
P.35 to 36
P.37 to 38
P.37 to 38
SVP
P.35 to 36
P.33
12.7
P.39 to 40
P.35 to 36
P.37 to 38
P.39 to 40
P.35 to 36
P.41 to 42
P.37 to 38
P.41 to 42
P.41 to 42
P.47 to 48
P.41 to 42
P.43 to 44
P.51 to 52
P.43 to 44
SXV
SVPE SVPE SVPS SVPF SVPD SVPE
SVPS
SVPS
SVPD SVPD SVPA SVPD
SVPC
P.41 to 42
SVPD
P.43 to 44
P.39 to 40
P.43 to 44
SVPA
P.51 to 52
SVP
Characteristics
Reliability
SXV
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVPC SVPC SVP SVPC
P.47 to 48
P.43 to 44
P.47 to 48
Fundamental
structure
SVPG
SVPS SVPF
SVPE
P.39 to 40
Recommended
soldering
condition
10.3
8.3
New
P.34
SVPS SVPG SVPF SVPB SVPB SVPF SVPG SVPF
P.51 to 52
8.0
12.0
7.0
8.3
6.6
6.6
6.6
P.45 to 46
10.0
6.0
5.5
5.0
P.35 to 36
New
Packing
specifications
（Radial lead type）
10.3
10.3
8.3
8.3
6.6
Products list
Packing
specifications
（SMD type）
Surface mount type
P.34
6.6
Image of
case size
SVPC
SVPA
P.47 to 48
P.49 to 50
SVPA
SVQP
P.49 to 50
P.51 to 52
P.51 to 52
SVQP
P.51 to 52
SVP
SVP
SVP
SVP
SVQP
SXE
Radial lead type
New
6.6
6.6
5.3
4.3
P.39 to 40
6.6
5.3
5.3
5.3
4.3
φ10.0
φ10.0
φ8.0
φ6.3
φ6.3
φ6.3
6.0
φ5.0
4.5
5.5
φ5.0
F12
size
φ8.0
φ6.3
φ4.0
F8
size
Technical data
C5
C55
C6
C10
E7
E12
size
size
size
size
size
size
10.3
A5
B45
B6
size
size
size
(Unit:mm)
Series system
diagram
P.51 to 52
SVP
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
※ Profile of case size are all indicated in maximum values.
POSCAP
Line-up
Guidelines and
precautions
Radial lead type
P.55 to 56
P.54
P.54
P.57 to 58 P.55 to 56 P.55 to 56
P.54
E9
E12
E12
E13
F8
F13
F13
size
size
size
size
size
size
size
P.57 to 58 P.55 to 56
P.54
New
P.53
φ10.0
P.55 to 56 P.57 to 58
φ10.0
Selection guide
φ10.0
Technical data
13.0
φ8.0
13.0
φ8.0
8.0
φ8.0
13.0
φ8.0
12.0
φ8.0
9.0
φ8.0
7.0
φ6.3
7.0
φ6.3
9.0
φ6.3
7.0
6.0
φ6.3
6.0
φ6.3
5.5
9.0
φ5.0
E7
size
12.0
B9
C55
C6
C6
C7
C9
E7
size
size
size
size
size
size
size
P.54
P.55 to 56
SEPC SEPF SEPF SEQP SEPC SEPC SEPF SEQP SEPC SEPF SXE SEPC SEQP SEPF SEPC
P.55 to 56 P.55 to 56 P.59 to 60
SEPC SEPC SEP
P.55 to 56 P.59 to 60
SEPC SEP
P.55 to 56
SEPC
P.57 to 58
SEQP
P.59 to 60
P.59 to 60
SEP
P.57 to 58
SEQP
Surface mount type
P.59 to 60
SEP
SEP
※ Profile of case size are all indicated in maximum values.
Catalog Deletion and
EOL models
16
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Products list
Size・ESR Matrix list / SMD type
V
2.0
μF
Series
3.3
4.7
6.8
8.2
10
15
18
22
27
33
39
47
56
68
82
100
SVPE
SVPE
SVPE
2.5
SVPC
SVPB
SVPA
B6（30）
SVP
SXV
SVPS
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVPC
4.0
SVPB
C5（40）
SVPA
B6（30）
SVQP
SVP
B6（60）
A5（200） B6（70）
SVPE
SVPE
SVPS
B6（30）
A5（200）
SVPC
6.3
SVQP
B6（30）
A5（200）
B6（30,25）
SVPB
C5（40）
SVPA
SVP
B6（30）
SVQP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
B6（70）
A5（200）
SVP
A5（220） A5（200）
SVPS
10
SVPD
C6（45）
SVPC
B6（30,23）
SVPB
C5（40）
SVPA
C6（30）
C6（45）
A5（240） A5（240）
SVP
POSCAP
Line-up
A5（220） A5（200）
C6（50）
B6（70）
SVPG
Guidelines and
precautions
C6（45）
B45（25）
SVPF
B6（27）
SVPE
SVPS
B6（90）
E7（30）
C6（24）
SVPD
16
SVPC
B6（35,27）
SVPB
C6（35,24）
A5（260）
B6（30）
SVPB
C5（45）
C55（35）
B6（40）
E7（33）
C6（35）
SVQP
E7（45）
C6（60）
SVP
B6（120）
SVPG
C6（60）
C6（60） E7（45）
SVPS
E7（60）
SVPD
C6（65）
SVPF
50
SVPF
63
SXV
100 SXV
F8（40） F8（40）
C6（30）
C6（30）
E12（24）
E7（24）
B6（40）
SVPF
SVPD
E7（45）
B45（30）
SVPF
35
F8（35）
E7（45）
C6（60）
SVPA
25
E7（40）
E7（45）
B45（27）
SVPS
17
E7（40）
C6（50）
B6（90）
SVPF
20
C6（24）
E7（30）
C6（50）
B6（120）
SVPG
Technical data
C6（30,25）
C5（40）
SVQP
SVP
F8（35）
E7（40）
SVPA
Catalog Deletion and
EOL models
C6（40）
C6（30）
B6（70）
SVQP
Surface mount type
C6（40）
C6（45）
SVPE
Catalog Deletion and
EOL series
Selection guide
C6（45）
E7（70）
E7（48）
F8（45）
C6（35）
E7（30）
F12（28）
E12（30）
E12（20）
F12（30）
F8（60） E12（50）
C6（40）
E7（28）
F12（20）
E12（25）
E7（35）
E12（25）
E12（40）
How to read the lists in P17 to 20
・ The name, sizes and ESR values of each series are found where the voltage (V) and
capacitance (μF) intersect each other. (Refer to the example.)
・ Please confirm the details in the list of each series from P33 to P60.
・ There are two or more same series names in a cell, which part number is different
each, so please check the characteristics list of the series.
Example
SVP
Series name
A5
Size
(240)
ESR value (unit:mΩ)
OS-CON
Line-up
120
150
180
220
270
330
SVPC
SVPB
820
1000
1200
1500
2700
B6（15,10） C6（10）
B6（30,24,19）
C6（25,15）
C6（16）
E7（20）
E12（9）
E12（10） F12（12）
C5（40）
C6（20）
SVP
E7（20）
F8（19）
C6（23）
SVPS
E12（13）
E7（22）
C6（22）
B6（30,23,20）
SVPC
E7（22）
C6（22）
C6（40）
SVP
C6（40）
SVPE
B6（12）
E7（22）
F8（20）
E7（35）
B6（15）
E12（13） F8（25）
F12（12）
C6（10）
B6（15）
SVPS
C6（22）
E7（22）
SVPC
B6（21）
C6（27,15）
C6（22）
E7（22）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
F8（20）
C6（17）
SVPG
E12（12） E12（12）
SVPB
SVQP
Packing
specifications
（Radial lead type）
F12（12）
E12（9）
SVPA
Products list
Packing
specifications
（SMD type）
F8（20）
C6（27,21,15）
SVPE
E7（22）
E12（12）
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVPB
SVPA
SVQP
SVP
SVQP
F8（20）
SVP
E7（35）
C6（17）
E7（35）
F8（25）
F8（25）
F8（25）
SVPE
F12（12）
E12（15）
C6（20）
E7（30）
SVPS
10
680
B6（10）
SVPA
6.3
560
C10（8）
B6（10）
SVPE
4.0
470
SVPE
SVPE
2.5
390
Image of
case size
Surface mount type
2.0
μF
Series
Series system
diagram
F8（24）
F8（30）
SVPD
SVPC
C6（27,22）
E7（22）
E7（19）
SVPB
SVPA
SVQP
SVP
E7（30）
E7（35）
E7（35）
E7（35）
F8（30）
F8（25）
E12（17）
C6（22）
SVPE
C10（11）
SVPS
F8（29）
SEQP
SEP
POSCAP
Line-up
C10（8）
SVPF
SEPC
F12（13）
F8（25）
SVPG
SEPF
Catalog Deletion and
EOL series
F8（24）
E7（35）
SXE
Radial lead type
V
Technical data
Size・ESR Matrix list / SMD type
Selection guide
Guidelines and
precautions
E7（22）
E12（14）
F12（12）
F12（10）
Guidelines and
precautions
SVPD
16
SVPC
E7（27）
E7（22）
E12（16）
Selection guide
SVPB
SVPA
F8（29）
SVQP
F8（30）
SVP
E12（20）
F12（16）
F8（30）
SVPG
SVPF
E7（25）
C6（25）
E12（14）
Technical data
F12（12）
SVPS
20
SVPB
SVPA
SVQP
SVP
F12（20）
SVPG
SVPF
25
SVPF
E12（16）
F12（14）
SVPS
SVPD
35
SVPF
F12（18）
Surface mount type
SVPD
50
SVPF
63
SXV
100 SXV
Standard sizes
A5
φ4.0×L5.5
(unit : mm)
B45
B6
φ5.0×L4.5
φ5.0×L6.0
C5
C55
C6
C10
φ6.3×L5.0
φ6.3×L5.5
φ6.3×L6.0
φ6.3×L10.0
E7
E12
φ8.0×L7.0
φ8.0×L12.0
F8
F12
φ10.0×L8.0
φ10.0×L12.7
※ Red letters ： New models
Catalog Deletion and
EOL models
18
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Products list
Size・ESR Matrix list / Radial lead type
V
μF
6.8
Series
10
15
18
22
33
39
47
56
68
82
100
120
150
B9（7）
2.5
SEPC
SEP
SXV
SEPC
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
4.0
SEQP
C6（40）
SEP
C6（40）
C6（40）
SEPC
6.3
SVQP
SEQP
C6（45）
E7（35）
SEP
C6（45）
E7（35）
SEPC
SVP
10
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
SEQP
C6（45）
E7（35）
SEP
C6（45）
E7（35）
SEPF
16
C55（30）
C6（24）
SEPC
SEQP
C6（50）
E7（40）
SEP
C6（50）
E7（40）
20
Guidelines and
precautions
Selection guide
SEQP
C6（60）
C6（60）
25
32
E7（45）
E7（45）
E7（45）
SEPF
SEQP
SEPF
63
SXE
C55（35）
E7（100）
F8（80）
E7（30）
19
F13（20）
φ5.0×L9.0
(unit : mm)
C55
C9
φ6.3×L5.5
φ6.3×L6.0
φ6.3×L7.0
φ6.3×L9.0
E7（28）
E12（20）
E12（40）
C7
Catalog Deletion and
EOL models
F13（20）
E12（24）
E12（50）
E12（25）
C6
Surface mount type
E12（24）
F8（40）
E7（25）
C6（35）
100 SXE
B9
F8（40）
C6（30）
SEPF
35
F8（40）
F8（35）
Standard sizes
Technical data
F8（30）
C6（25）
SEP
POSCAP
Line-up
F8（30）
SEPF
Catalog Deletion and
EOL series
E7（22）
C9（10）
E7
E9
E12
E13
φ8.0×L7.0
φ8.0×L9.0
φ8.0×L12.0
φ8.0×L13.0
F8
F13
φ10.0×L8.0
φ8.0×L12.0
F13（18）
OS-CON
Line-up
220
270
330
B9（7）
2.5
390
C6（10）
470
560
B9（7）
B9（7）
C9（7）
C9（7）
E7（8）
E9（8）
E9（5,7）
C6（10）
E13（7）
C9（7）
SEPC
SEP
SEPC
1200
E13（7）
1500
E9（7）
2700
F13（10）
F13（12）
E7（35）
SEP
E7（35）
E7（35）
C55（18）
SEPC
Fundamental
structure
Characteristics
Reliability
SXV
E12（13）
F8（25）
F8（25）
E12（13）
F8（25）
E9（8）
C9（7）
F13（7）
C9（7）
E9（7）
F13（12）
F13（12）
E7（18）
F13（10）
C7（20）
SEQP
F8（25）
E12（15）
F13（12）
SEP
F8（25）
E12（15）
F13（12）
SEPC
E7（22）
SEQP
F8（25）
E12（17）
F13（13）
SEP
F8（25）
E12（17）
F13（13）
SEPC
Recommended
soldering
condition
SVPG
E13（8）
6.3
SEPF
Packing
specifications
（Radial lead type）
F13（7）
E13（7）
SEQP
20
1000
Products list
Packing
specifications
（SMD type）
E9（7）
4.0
16
820
E12（13）
C9（7）
10
680
Image of
case size
C6（22）
E9（10）
E12（16）
E7（22）
E7（13）
E12（14）
E12（11）
E12（20）
F13（16）
E12（20）
F13（16）
SEPF
E7（25）
E12（14）
SVPS
SVPD
SVPC
SVPB
SVPA
SVP
F13（12）
F13（10）
SEP
SVPE
SVQP
E9（10）
SEQP
SVPF
Surface mount type
Series
180
Series system
diagram
F13（12）
SXE
Radial lead type
V
μF
Technical data
Size・ESR Matrix list / Radial lead type
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
SEQP
SEP
25
32
SEPF
E12（16）
POSCAP
Line-up
F13（14）
Guidelines and
precautions
SEPF
SEQP
35
SEPF
63
SXE
100 SXE
Selection guide
※ Red letters ： New models
Technical data
Surface mount type
Catalog Deletion and
EOL models
20
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Packing
specifications
（SMD type）
Specifications for SMD type
1. Part number system
1 6
S
Rated voltage
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Radial lead type
SEPC
SEP
Rated capacitance
2.0
2.5
2R5
6.3
6
4.0
10
20
20
16
10
SVPD
100
SVPE
470
22
220
SVPS
25
35
SVPB
4.7
SVPC
16
SVPF
35
100
SVQP
3.3
SVPA
4
10
Rated cap.(μF)
SVP
2
1,500
SVPG
100
SXV
2. Taping
2-1. Carrier tape
4.0±0.1
t
2.0±0.1
φ1.5± 0.1
0
E
Catalog Deletion and
EOL series
W
F
POSCAP
Line-up
B
Guidelines and
precautions
T
P
A
Mounting parts
Selection guide
Direction of unreeling
(unit : mm)
Dimension
Size code
Technical data
Surface mount type
Catalog Deletion and
EOL models
21
3
Example
25
SEQP
3 R
Series name
Code
Rated volt.
SVP
SEPF
P
Example
SVQP
SXE
V
A
4.7
B
W
F
E
4.7
12.0
5.6
16.0
6.9
16.0
6.9
16.0
6.9
16.0
±0.3
±0.1
P
5.5
1.75
7.5
1.75
±0.1
±0.1
7.5
1.75
12.0
7.5
1.75
12.0
7.5
1.75
12.0
8.0
t
0.4
A5
±0.2
B6
±0.2
C5
±0.2
C55
±0.2
C6
±0.2
C10
±0.2
±0.2
7.0
24.0
11.5
1.75
16.0
±0.1
±0.1
8.6
8.6
24.0
11.5
1.75
12.0
0.4
5.6
6.9
6.9
6.9
7.0
±0.2
±0.2
±0.2
±0.2
±0.2
±0.3
±0.3
±0.3
±0.3
±0.3
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
8.0
±0.1
±0.1
±0.1
±0.1
0.4
±0.1
0.4
±0.1
0.4
±0.1
0.4
±0.2
8.6
24.0
11.5
1.75
16.0
±0.1
±0.1
F8
10.7
10.7
24.0
11.5
1.75
16.0
0.4
F12
10.7
10.7
24.0
11.5
1.75
16.0
8.6
±0.2
±0.2
±0.2
±0.2
±0.3
±0.3
±0.3
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
6.2
±0.2
6.2
10.5
±0.2
±0.1
5.3
±0.2
0.5
E12
±0.1
6.2
±0.2
±0.2
±0.2
±0.3
5.8
±0.2
±0.1
E7
±0.2
T
±0.2
7.2
±0.1
±0.2
0.5
12.3
±0.2
8.2
±0.1
±0.2
0.4
13.0
±0.1
※Please contact us separately concerning about B45 size of SVPG series.
±0.2
Code
3R3
4R7
10
22
100
220
470
1500
M
Capacitance
tolerance
Cap.
tolerance
Code
±20％
M
OS-CON
Line-up
2±0.5
(unit : mm)
Size code
φ80±1.0
φ13±0.2
φ21±0.8
R1.0
A5
W1
Technical data
Direction of unreeling
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
W2
13.0±0.5 17.5±1.0
B6, C5, C55, C6 17.0±0.5 21.5±1.0
C10, E7, F8, E12, F12 25.0±0.5 29.5±1.0
※Please contact us separately concerning
about B45 size of SVPG series.
SXV
SVPG
SVPF
Surface mount type
2-2. Reel
Selection guide
Guidelines and
precautions
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
W1
W2
Direction of unreeling
2-3. Polarity
SVP
SXE
Radial lead type
φ380±2.0
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
3. Minimum packing quantity and weight
Taping type
Size code
Quantity(pcs./Reel,φ380) Typical weight(g)
A5
2,000
700
C5
1,300
800
B6
C55
C6
C10
1,500
1,000
1,000
500
800
800
800
700
E7
1,000
1,100
F8
500
1,000
E12
F12
400
400
Technical data
800
Surface mount type
1,000
※Please contact us separately concerning about B45 size of SVPG series.
Catalog Deletion and
EOL models
22
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
SXV
Packing
specifications
（Radial lead type）
Specifications for radial lead type
1. Part number system
1 6
S E P C
4 7 0
M
T
Rated voltage
Series name
Rated capacitance
Capacitance
tolerance
Taping or forming of
terminal code
Example
SVPF
Rated volt. Code
Surface mount type
SVPG
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
2.5
4.0
6.3
20
32
SVP
100
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
SEPC
6
20
Rated cap.
(μF)
SEQP
4
10
16
SEP
2R5 ※1
10
25
SVQP
Example
SXE
16
6.8
6R8
22
22
10
SEPF
100
220
25
470
32
1,000
100
Code
2,700
Cap.
tolerance
Code
±20％
M
10
Taping or lead
terminal wire
process code
None suffix for
regular Iength lead
type products
100
220
470
1000
2700
※1 Code 2 is used for 2.5V products of B9,C6,C9,E7,E9 and F13 size in SEPC series.
2. Lead terminal process
2-1. Applications
※ The following table is a standard specification. Please contact us separately concerning specifications except for that mentioned below.
Because of a limit on the length of a model name, the part of process name changes to +S from +TSS, +D from +TS, +3 from +C3.
Please contact us for details.
Series
Size code
SEP
SEQP
SEPC
SEPF
SXE
Bag-packed products (lead terminal cutting)
Taping
Not processed
Straight cut
B9,C55,C6,C7,C9,E7,E9,E12
○
＋C3
＋TSS （＋S）
E13
○
＋C3
＋TS （＋D）
F8,F13
○
＋C3
＋T
2-2. Lead terminal cutting
Lead terminal
cutting code
＋C3
（＋3）
Process
names
Straight
cut
Dimensions (unit : mm)
Size code (φD)
B9（φ5）
C55,C6，C7,C9（φ6.3）
E7，E9，E12，E13（φ8）
F8，F13（φ10）
Size code
F
Surface mount type
Catalog Deletion and
EOL models
23
F±1
Technical data
L±0.5
B9
2.0
L
C3
3.5
C55,C6,C7,C9 E7, E9, E12, E13
2.5
3.5
F8, F13
5.0
OS-CON
Line-up
Selection guide
Guidelines and
precautions
2-3. Lead terminal taping
F
φD0
t
P2
（＋D）
F
P0
φD0
t
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
h
W2
W1
P1
Packing
specifications
（Radial lead type）
Carrier
Tape
P
H
E13（φ8）
L
F＝3.5mm
Hold-down Tape
W0
P1
P0
＋TS
W2
W
F8,F13（φ10）
h
H
F＝5.0mm
L
＋T
P
Products list
Packing
specifications
（SMD type）
W
P2
Technical data
Taping
Image of
case size
Hold-down Tape
Carrier
Tape
SVPF
Surface mount type
Size code (φD)
W1
Ｆ
W0
Taping code
Series system
diagram
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
E7,E9,E12（φ8）
P1
F
P0
φD0
t
Hold-down Tape
Carrier
Tape
(unit : mm)
Code
F
P
P0
P1
P2
Δh
W
W0
W1
Tolerance
＋0.8
−0.2
±1.0
±0.2
±0.5
±1.0
±1.0
±0.5
min.
±0.5
W2
H
φD0
t
L
max ±0.75 ±0.2
±0.3
max
max
5.0 12.7 12.7 3.85 6.35
0
18.0
9.5
9.0
2.5
18.5 4.0
0.6
0
11.0
＋TS（＋D） φ8
3.5 12.7 12.7 4.60 6.35
0
18.0
9.5
9.0
2.5
17.5 4.0
0.6
0
11.0
φ5
2.0 12.7 12.7 5.35 6.35
0
18.0
9.5
9.0
2.5
17.5 4.0
0.6
0
11.0
φ6.3
2.5 12.7 12.7 5.10 6.35
0
18.0
9.5
9.0
2.5
17.5 4.0
0.6
0
11.0
φ8
3.5 12.7 12.7 4.60 6.35
0
18.0
9.5
9.0
2.5
17.5 4.0
0.6
0
11.0
＋T
φ10
＋TSS
（＋S）
SXE
Radial lead type
F＝3.5mm
W2
W
C55,C6,C7,C9（φ6.3）
W0
B9（φ5）
F＝2.5mm
h
W1
（＋S）
F＝2.0mm
L
＋TSS
P
H
P2
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Technical data
3. Minimum packing quantity and weight
Processed type discrete lead terminals
Zig-zag pack taping type
Size code
Case size
Quantity(pcs./Bag)
Typical weight(g)
B9
φ5
500
180
2,000
1,000
C55
φ 6.3
500
150
1,500
650
C6
φ 6.3
500
160
1,500
700
C7
φ 6.3
500
210
1,500
920
C9
φ 6.3
500
240
1,500
1,000
E7
φ 8
200
110
1,000
820
E9
φ 8
200
130
1,000
900
E12
φ 8
200
200
1,000
980
E13
φ 8
200
160
1,000
1,060
F8
φ10
200
180
500
890
F13
φ10
200
280
500
940
Quantity(pcs./Bag) Typical weight(g)
Surface mount type
Catalog Deletion and
EOL models
24
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Peak temperature 250℃ lead free reflow soldering profile
The cycles of reflow soldering: Twice (max)
Temperature on the
surface of capacitor
Image of
case size
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Recommended
soldering
condition
250℃
230℃
220℃
200℃
180℃
40s max
50s max
150℃
120s max
60s max
Time(sec.)
Peak temperature 260℃ lead free reflow soldering profile
The cycles of reflow soldering: Once (max)
Temperature on the
surface of capacitor
OS-CON
Line-up
260℃
230℃
220℃
200℃
180℃
40s max
50s max
150℃
120s max
60s max
Time(sec.)
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Soldering with a soldering iron
Tip of a soldering iron: 400±10℃
Working time: 5sec. max
Flow soldering
Temperature
Time
Flow number
Preheating
120℃ or less
(ambient temperature)
120 sec. or less
1 time
Soldering
condition
260 ＋ 5℃ or less
10 ＋ 1 sec. or less
Technical data
2 times or less
※1. When soldering 2 times, total immersion time should be 10 ＋ 1 sec. or less.
Surface mount type
Catalog Deletion and
EOL models
25
※1
OS-CON
Line-up
Fundamental
structure
1. Basic structure of OS-CON
OS-CON has a basic construction similar to an aluminum electrolytic capacitor.
A distinctive difference lies in electrolyte.
Separator sheet impregnated with electrolytic solution.
Aluminum electrolytic capacitor
Separator sheet impregnated with conductive polymer.
Liquid electrolyte
Technical data
Selection guide
Guidelines and
precautions
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Solid electrolyte
SXV
Separator sheet
Anode aluminum foil
Aluminum case
Cathode aluminum foil
Cathode aluminum foil
Separator sheet
Anode aluminum foil
Anode terminal
Surface mount type
Element
Aluminum
case
Sealing
rubber
Dielectric oxidization layer Electrolyte impregnating separator sheet
(Electrolyte serves as the actual cathode.)
(aluminum oxide)
Cathode Anode terminal
terminal
Cathode terminal
Anode
terminal
Plastic spacer
Characteristics between OS-CON and aluminum electrolytic capacitor due to a difference in electrolyte
Aluminum electrolytic capacitor
0.01S/cm
Conductivity
100S/cm
・Difficult to lower ESR due to low conductivity ・The highest electronic conductivity, realizing
super low ESR.
・ESR augments, in particular, in low temperature
・ESR is stable in low temperature conditions
conditions
・Liquid electrolyte is evaporable at high temperature ・Little evaporation due to solid electrolyte
・Static capacitance is on the decline at high ・Little decrease in static capacitance
・Long lifespan even at high temperature
Reliability, lifespan temperature
・Limited lifespan resulting from dry-up
・Very minor fluctuations in temperature
・Major fluctuations in temperature characteristics characteristics
Temperature coefficient
(for lifespan)
2 times by 10℃ reduction
Surface mount type
Radial lead type
Enlarged section diagram of the element
Cathode
terminal
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
SXE
Radial lead type
Sealing rubber
SVPG
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
10 times by 20℃ reduction
105℃/2,000h→85℃/8,000h
105℃/2,000h→85℃/20,000h
Selection guide
※Please contact us separately if you require life factor
of SXV, SXE series.
2. OS-CON Manufacturing Method
【Radial lead type】
【Surface mount type】
Aluminum etching foll
Aluminum etching foll
Forming
Forming
Foil slitter
Winding
Lead wire
Separator Sheet
Forming and carbonization
Foil slitter
Winding
Technical data
Lead wire
Separator Sheet
Forming and carbonization
Conductive polymer
impregnation and polymerization
Conductive polymer
impregnation and polymerization
Rubber・Case
Surface mount type
Rubber・Case
Rubber sealing (curl)
Rubber sealing (curl)
Marking
Aging and Inspection
Aging and Inspection
Forming and Marking
Packing and Shipping
Packing and Shipping
Plastic Spacer
Catalog Deletion and
EOL models
26
OS-CON
Line-up
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Characteristics
1. OS-CONElectrical characteristics
1-1. Frequency characteristics
100
(at
（25℃）
25℃)
A：OS-CON
16V/56μF（φ8×6.9L：347 ）
B：AI-E（Low impedance）
16V/47μF（φ6.3×7L：218 ）
C：Ta-cap
16V/47μF（φ6.3×11L：311 ）
D：AI-E（Low impedance）
16V/1,000μF（φ16×25L：5,024 ）
SXV
Surface mount type
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Impedance（Ω）
SVPG
SVPF
Fig.B Impedance & ESR frequency characteristics
(several OS-CON models)
Fig.A Impedance frequency characteristics
(OS-CON vs other types)
10
1
B
C
0.1
100
OS-CON
A→35SVPD8R2M
B→16SVPA82MAA
C→4SEPC560MX
D→2SEPC2700M
10
Impedance（Ω）
ESR（Ω）
Image of
case size
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
1
(at
（25℃）
25℃)
ESR
A
D
0.1
B
A
B
C
C
0.01
D
Impedance
D
A
0.01
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
1K
10K
Frequency（Hz）
Fig.A ESR temperature characteristics
(OS-CON vs other types)
100K
10M20M
1M
Frequency（Hz）
ESR (Ω)
Ta
OS
CR(X5U)
0.001
−55
CR(X5P)
−20
0
20
Temperature (℃)
OS
10μF
Al
0.01
Capacitance change
at 120kHz
10
10μF
1
Temperature characteristics
20
Equivalent series resistance
at 100kHz
0.1
27
10K
Fig.B Capacitance temperature characteristics
(OS-CON vs other types)
Temperature characteristics
10
Catalog Deletion and
EOL models
1K
1-2. Characteristics at high temperature and low temperature
Selection guide
Surface mount type
0.001
10M20M
1M
The OS-CON is an electrolytic capacitor that has excellent frequency characteristics. It improves ESR greatly, and
provides the excellent frequency characteristics because the OS-CON uses a high conductive polymer as electrolyte.
Fig.A: The OS-CON’s frequency characteristic shows a nearly ideal curve. When compared at 100kHz,
The OS-CON 56μF, and low impedance aluminum electrolytic capacitor 1,000μF nearly have the same feature.
Fig.B: The resonance point of the OS-CON is at 100kHz to 10MHz. The ESR is an extremely small value
approximately 5mΩ at 100kHz of 560μF.
100
Technical data
100K
Capacitance change (%)
SVQP
Al
Ta
0
CR(X5P)
−10
−20
CR(X5U)
−30
−40
−50
85
105
OS-CON’s Characteristics at high temperature and
low temperature is that it features little change in
temperature for the ESR.
What ESR changes a little against temperature
means that noise clearing ability changes a little
against temperature as well. The OS-CON is suitable
for outdoor apparatus.
−55
−20
0
20
Temperature (℃)
85
105
OS =OS-CON
Purple
AI =AL-E. Cap
Blue
Ta
=Tantalum Cap.
Green
CR(X5P) =Cera Cap. (X5P Type)
Red
CR(X5U) =Cera Cap. (X5U Type)
Pink
OS-CON
Line-up
1-3. Bias characteristics
(a) Capacitance
Bias voltage characteristics
OS.1 =OS-CON(10SVP10M) Purple
0
10μF
OS.1
OS.2 =OS-CON(25SVPD10M)
Light Purple
CR(X5P) =Cera Cap.
OS.2
Red
Pink
(X5U Type ; 50V/10μF)
CR(X5U)
CR(X5P)
10
20
Bias voltage (V)
30
35
When voltage is applied to
ceramic capacitors, they show a
bias characteristics where static
capacitance is reduced. Our
OS-CON product, however, will
show no reduction in capacitance for applied voltage within
its rating.
10
Z
0.1
ESR
0.01
100
1,000
Frequency(kHz)
10,000
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVP
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
OS-CON（25SVPD10M）
0V bias
POSCAP
Line-up
Guidelines and
precautions
10
1
Z
Selection guide
ESR
0.1
Multi-layer ceramic capacitor (25V/4.7μF)
20V bias
10
Z
1
0.1
ESR
0.01
0.001
10
0.001
10
100
ESR, Impedance(Ω)
ESR, Impedance(Ω)
Recommended
soldering
condition
0.01
0.001
10
100
100
ESR, Impedance(Ω)
ESR, Impedance(Ω)
Multi-layer ceramic capacitor (25V/4.7μF)
0V bias
1
Packing
specifications
（Radial lead type）
SVQP
(b) Impedance, ESR
Bias characteristics of OS-CON & ceramic capacitors
100
Products list
Packing
specifications
（SMD type）
Radial lead type
−10
−30
0
Image of
case size
(X5P Type ; 10V/10μF)
CR(X5U) =Cera Cap.
−20
Series system
diagram
Surface mount type
Capacitance change (%)
Capacitance change
at 120Hz
Technical data
Selection guide
Guidelines and
precautions
100
1,000
Frequency(kHz)
10,000
Technical data
OS-CON (25SVPD10M)
20V bias
10
1
0.1
Z
Surface mount type
ESR
0.01
100
1,000
Frequency(kHz)
10,000
0.001
10
100
1,000
Frequency(kHz)
ESR & impedance of ceramic capacitors change largely between 300kHz to 1MHz.
As for OS-CON, neither ESR nor impedance changes.
10,000
Catalog Deletion and
EOL models
28
OS-CON
Line-up
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
1-4. Allowable Ripple Current
3.74
3.5
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
2
0
Blue
Green
※Samples of SVP series are
approximate models.
1.80
1.39
1.15
1.10
1
0.5
Light Purple
Ta.Cap. (Low ESR)
2.67
2.5
1.5
OS-CON (SVP series)
AI-E. Cap. (Low Impedance)
3
SVQP
SVP
Allowable Ripple Current（100kHz45℃）
4
Ripple Current（Arms）
Image of
case size
Characteristics
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
0.84
0.45
0.74
16V/33μF
0.45
0.45
0.48
16V/47μF 10V/100μF 10V/220μF
When selecting smoothing capacitors for power supply, the allowable ripple current of a capacitor is
one of criterion.
The allowable value of ripple current is decided by the generated heat of a capacitor, this heating is
due to the ESR. Since a large ESR capacitor generates larger heat value, it can not make the flow of
ripple current greater.
Compared to other electrolytic capacitors, ESR of the OS-CON is so small that it can allow much
ripple currents.
1-5. ESL Characteristics
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Technical data
The OS-CON is a capacitor of high performance with low ESR and large capacitance.
Recently in circuit technologies, the constituent of ESL is important in the domain of the
high frequency with that of electronic equipment.
(a) Eqivalent series circuit of capacitor
ESL
(b) Approximate ESL values of SEPC series
(unit:nH)
Surface mount type
Catalog Deletion and
EOL models
29
Size
Code
at 10 MHz
at 40 MHz
B9
C55
C6
C7
C9
E7
E9
E12
E13
F13
1.6
2.4
2.6
2.3
2.2
2.9
2.7
4.3
4.3
6.0
1.5
2.3
2.5
2.3
2.1
2.8
2.6
4.1
4.1
5.8
※Measuring position: root of lead terminal
※Measuring method: Based on JEITA RC-2003
※All values on left figure are not guaranteed but
reference.
Please contact SANYO for details of measurement.
OS-CON
Line-up
Guidelines and
precautions
Capacitance change
at 120Hz
10V/22μF
70℃
−1
85℃
105℃
−10
145℃
135℃
125℃
155℃
The decrease in capacitance of the
OS-CON depends on temperature.
The left figure shows the speed
of capacitance decrease at
each temperature. This graph
indicates that temperature
coefficient of the OS-CON
lifetime is 10 times by 20℃
reduction.
Compared with this, aluminum
capacitor lifetime is 2 times by
10℃ reduction.
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
Capacitance change（％）
1. Temperature acceleration test (Endurance)
Technical data
Selection guide
Reliability
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
100
Time（h）
SVP
1,000
Estimation of life time
OS-CON
105℃
95℃
85℃
75℃
Aluminum electrolytic capacitor
⇒ 2,000h
⇒ 6,324h
⇒ 20,000h
⇒ 63,245h
105℃
95℃
85℃
75℃
⇒ 2,000h
⇒ 4,000h
⇒ 8,000h
⇒ 16,000h
※Guaranteed temperature of the OS-CON is 105℃,
except for SEQP, SVQP and SVPD series.
※Time is an estimate, not guaranteed.
Though the OS-CON and an
aluminum electrolytic capacitors
are guaranteed on 2,000 hours
at 105℃, the life span results in
differences as temperature
drops.
The OS-CON has a longer life
span compared with an
aluminum electrolytic capacitor.
SXE
Radial lead type
10
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
2. Self-Healing Mechanism
The dielectric substance of the OS-CON is a non-conductive oxide film that has formed
on the surface of an anode aluminum foil. Since the oxide film is solid and thin, leakage
current may temporarily increase if micro cracks are generated by external stress (i.e.
mechanical, thermal, electrical) [see figure (b)]. When this happens, the leakage current
generates Joule heat [see figure (c)] and with this heat the electrolyte turns
non-conductive and insulates the outlet of the leakage path [see figure (d)]. The
leakage current from the micro cracks is thus suppressed through this function. This is
known as "self-healing mechanism."
Electrolyte
Crack generated by
an external impact
Heating by Joule heat
Insulation of electrolyte,
a part of heating
Technical data
Surface mount type
Dielectric oxide film
Anode aluminum foil
（a）
Leakage current
（b）
Leakage current
（c）
（d）
Catalog Deletion and
EOL models
30
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Reliability
3. Reliability presumption of life for the OS-CON
The capacitance of the OS-CON is getting smaller as time goes with endurance test.
This means wear-failure of the OS-CON is open mode, which is a main failure factor.
The life time is different by each operating temperature and self-heating by ripple current.
The following formula is used to to estimate the presumptive lifetime of the OS-CON at ambient
temperature
Tx (℃).
The result of the following estimation is not guaranteed but presumptive values based
on actual measurement. The estimated life-span is limited up to 15 years.
3-1. Calculation formula of estimated life expectancy
Lx＝Lo×10
To−Tx
20
Lx : Life expectance (h) in actual use (temperature Tx)
Lo : Guaranteed (h) at maximum temperature in use
To : Maximum operating temperature (℃)
Tx : Temperature in actual use (ambient temperature of the OS-CON) (℃)
Please contact us separately about estimated life expectancy of new series (SXV, SXE
series) and products (SVQP, SVPD, SEQP series) guaranteed at 125℃.
※The estimated life expectancy of conductive polymer electrolyte type can be calculated
without consideration of self-heating under application of the ripple current
※SVPS series: Self-heating temperature when applied the allowable ripple current.
POSCAP
Line-up
Guidelines and
precautions
Self-heating temperature when applied the rated ripple current
series
SVP, SVPA, SVPC, SVPS
SVP, SVPA, SVPC, SVPS ※
SVPB, SVPE, SVPF, SVPG, SXV, SEP, SEPC, SEPF, SXE
SVQP, SEQP, SVPD
※
Selection guide
Technical data
Surface mount type
Catalog Deletion and
EOL models
31
size
Except for A5, B6
A5,B6
All
All
Self-heating
approx. 20℃
approx. 10℃
approx. 20℃
approx. 2℃
OS-CON
Line-up
Leakage current ESR（mΩ at 100kHz） tanδ（at 120Hz） Capacitance change（%）
（μA at 16V30s）
4-1. Endurance (105°
C, 16V applied)
20
Characteristics on Endurance
10
0
−10
−20
0
0.1
5,000
10,000
0.08
Little change in
characteristics can be seen
after 10,000 hours because
of adoption of conductive
polymer that excels in
thermal stability.
0.06
0.04
0.02
0
0
100
5,000
10,000
Technical data
(16SVP39M)
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
4. Conductive polymer type
Selection guide
Guidelines and
precautions
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
80
SVQP
60
SVP
20
0
0
100
5,000
10,000
10
1
0.1
0
SXE
Radial lead type
40
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
5,000
10,000
POSCAP
Line-up
Leakage current ESR（mΩ at 100kHz） tanδ（at 120Hz） Capacitance change（%）
（μA at 16V30s）
4-2. Damp heat (60°
C90% RH, without load)
Characteristics on damp heat
20
10
0
−10
−20
0
0.1
5,000
10,000
5,000
10,000
0.08
0.06
0.04
Little change in
characteristics can be seen
after 10,000h hours in a
high temperature and damp
heat environment because of
the excellent thermal
stability of conductive
polymer.
Guidelines and
precautions
Selection guide
Technical data
0.02
0
0
100
80
60
40
Surface mount type
20
0
0
100
5,000
10,000
5,000
10,000
10
1
0.1
0
Catalog Deletion and
EOL models
32
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SXV
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Items
Condition
Specifications
(V)
−
63
100
Surge voltage
(V)
Room temperature
72.5
115.0
Category temperature range (℃)
Capacitance tolerance
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
Dissipation Factor (DF)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋105
−
120Hz/20℃
(％)
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
60℃, 90 to 95%RH,
1,000h,
No applied voltage
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
SVP
SEP
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
Marking and dimensions
227
SXV
33
63
Series
（SXV）
E12
L
Rated voltage
Size list
RV
R
±0.5
L
8.0
＋0.1
−0.4
W ±0.2 H
11.9
8.3
±0.2
8.3
C
±0.2
R
P
9.0 0.8∼1.1
±0.2
3.2
63
（＋）
Recommended land pattern dimension of PWB
RV : Rated voltage
15
33
Size
code φD
W
Rated capacitance
Selection guide
μF
(unit : mm)
0.2max
Polarity marking
（Cathode）
Case No.
Guidelines and
precautions
Technical data
ESR
※1 In case of some problems for measured values, measure after applying rated voltage.
※2 Please refer to page 25 for reflow soldering conditions.
Catalog Deletion and
EOL series
POSCAP
Line-up
Within 1.3 times of the initial limit
100
(unit : mm)
E12
C
SEQP
VPS (230℃ X 75s)
Within ±10% of the initial value
DF
P
C
SEPC
Resistance to soldering heat※2
△C/C
H
SEPF
φD
Radial lead type
SXE
0.75 to 1.25
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
105℃, 5,000h,
Rated voltage applied
Endurance
Damp heat(Steady state)
SVQP
RoHS directive/Halogen-free compliant
Super high voltage（100V）
Endurance： 105℃ 5,000h
Rated voltage
Equivalent series resistance (ESR)
SVPG
Series
Specifications
Leakage current※1
SXV
NEW
E12
Size code
a
b
c
2.8
11.1
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
E12
1.9
a
b
SXV series characteristics list
Surface mount type
Size
code
E12
Part number
Rated
voltage
(V)
63SXV33M
100SXV15M
Rated
capacitance
(μF)
ESR(mΩ) (max)
100kHz to 300kHz/20℃
63
33
25
2950
12
104
100
15
40
2350
12
75
Frequency coefficient for ripple current
Catalog Deletion and
EOL models
33
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Series
OS-CON
Line-up
HS directive/Halogen-free compliant
Low ESR（8mΩ）
High rated ripple current（5,800mArms）
Selection guide
Guidelines and
precautions
Specifications
Condition
Specifications
(V)
−
16
20
25
Surge voltage
(V)
Room temperature
18
23
29
Capacitance tolerance
−
−55 to ＋105
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Dissipation Factor (DF)
Leakage current※1
Equivalent series resistance (ESR)
Characteristics of impedance
ratio at high temp.
and low temp.
Based the value at
100kHz, ＋20℃
−55℃ Z/Z20℃
0.75 to 1.25
＋105℃ Z/Z20℃
0.75 to 1.25
105℃, 5,000h,
Rated voltage applied
Endurance
Resistance to soldering heat※2
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
60℃, 90 to 95%RH,
1,000h,
No applied voltage
Damp heat(Steady state)
△C/C
VPS (230℃ X 75s)
Reliability
SVPF
Within 1.5 times of the initial limit
SVPE
SVPS
SVPD
Within the initial limit
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
SVQP
SVP
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
SVPC
SVPB
SVPA
SXE
SEPF
SEPC
SEQP
SEP
(unit : mm)
Size φD
code
W
P
C
B45
C10
±0.5
5.0
6.3
L
＋0.1
−0.4
W
4.4
9.9
±0.2
H
5.3
6.6
±0.2
5.3
6.6
C
±0.2
R
P
6.0 0.6∼0.8
7.3 0.6∼0.8
±0.2
1.4
2.1
POSCAP
Line-up
Guidelines and
precautions
Rated capacitance
L
Rated voltage
Size list
RV
16
R
25
15
(unit : mm)
Size code
B45
33
Selection guide
Recommended land pattern dimension of PWB
RV : Rated voltage
20
（＋）
C
μF
Characteristics
△C/C
H
15
25
Fundamental
structure
LC
Series
（PG）
Recommended
soldering
condition
Catalog Deletion and
EOL series
0.2max
φD
PG
Packing
specifications
（Radial lead type）
SXV
Marking and dimensions
003
Products list
Packing
specifications
（SMD type）
SVPG
※1 In case of some problems for measured values, measure after applying rated voltage.
※2 Please refer to page 25 for reflow soldering conditions.
Polarity marking
（Cathode）
Case No.
Image of
case size
Surface mount type
Category temperature range (℃)
Technical data
Items
Rated voltage
Series system
diagram
Radial lead type
SVPG
Surface
mount type
NEW
B45
47
B45
a
270
C10
b
a
b
c
B45
1.4
7.4
1.6
C10
2.1
9.1
1.6
Technical data
SVPG series characteristics list
Size
code
B45
C10
Part number
Rated
voltage
(V)
Rated
capacitance
(μF)
ESR(mΩ) (max)
100kHz to 300kHz/20℃
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
25SVPG15M
25
15
30
2800
12
75
20SVPG33M
20
33
27
3000
12
132
16SVPG47M
16
47
25
3200
12
150
16SVPG270M
16
270
8
5800
12
864
Surface mount type
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Catalog Deletion and
EOL models
34
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVPF
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Items
Condition
Rated voltage
(V)
Surge voltage
Capacitance tolerance
Dissipation Factor (DF)
(V)
Room temperature
(％)
120Hz/20℃
Leakage current※1
Equivalent series resistance (ESR)
100kHz to 300kHz/20℃
−55℃
SEQP
SEP
Within 1.5 times of the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
DF
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
Within ±10% of the initial value
Within 1.3 times of the initial limit
ESR
Marking and dimensions
0.2max
B6, C6 size ： PF
E7, E12, F12
size ： SVPF
Rated capacitance
(unit : mm)
W
H
82
25
SVPF
Series
φD
003
Guidelines and
precautions
L
R
Rated voltage
Size
code φD
（＋）
Selection guide
Size list
μF
RV
16
RV : Rated voltage
20
25
35
10
E7
C6
22
27
B6
E7
39
47
E12
C6
56
B6
C6
68
82
50
C6
18
F12
E7
B6
100
E12
E7
120
F12
C6
180
C6
270
E7
E7
330
E12
F12
390
35
Within 1.5 times of the initial limit
※1 When measured values are questionable, measure after voltage processing mentioned below.
Voltage processing: Apply voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for reflow soldering conditions.
POSCAP
Line-up
Catalog Deletion and
EOL models
Within the initial limit
ESR
VPS (230℃ X 75s)
Polarity marking
（Cathode）
Case No.
Surface mount type
Within 1.5 times of the initial limit
ESR
△C/C
heat※2
Catalog Deletion and
EOL series
Technical data
0.75 to 1.25
Within ±20% of the initial value
DF
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
57
0.75 to 1.25
LC
Damp heat(Steady state)
−55 to ＋105
50
40
Please see the attached characteristics list
Z/Z20℃
＋105℃ Z/Z20℃
105℃, 5,000h,
Rated voltage applied
35
29
Please see the attached characteristics list
△C/C
Endurance
25
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
P
C
Radial lead type
SEPF
SEPC
23
M : ±20
120Hz/20℃
Based the value at
100kHz, ＋20℃
20
18
−
SVP
SXE
Specifications
16
−
Category temperature range (℃)
Resistance to soldering
SVQP
RoHS directive/Halogen-free compliant
High voltage（50V）
Large capacitance（1,000μF）
Endurance： 105℃ 5,000h
Specifications
Characteristics of impedance
ratio at high temp.
and low temp.
SXV
Series
E12
560
E12
1000
F12
F12
±0.5
±0.2 H
L ＋0.1
−0.4 W
±0.2
C
±0.2
R
P
±0.2
B6
5.0
5.9
5.3
5.3
6.0 0.6∼0.8
1.4
C6
6.3
5.9
6.6
6.6
7.3 0.6∼0.8
2.1
E7
8.0
6.9
8.3
8.3
9.0 0.6∼0.8
3.2
E12
8.0
11.9
8.3
8.3
9.0 0.8∼1.1
3.2
F12
10.0
12.6 10.3 10.3 11.0 0.8∼1.1
4.6
OS-CON
Line-up
SVPF series characteristics list
C6
E7
E12
F12
Rated
capacitance
(μF)
ESR(mΩ) (max)
100kHz to 300kHz/20℃
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
25
27
40
2450
12
135
20SVPF56MX
20
56
30
2800
12
224
16SVPF82M
16
82
27
3000
12
262
50SVPF10M
50
10
40
2500
12
100
SXV
SVPG
Technical data
25SVPF27MX
Fundamental
structure
Characteristics
Reliability
35SVPF22M
35
22
35
2600
12
154
25SVPF47M
25
47
30
2800
12
235
25SVPF56M
25
56
30
2800
12
280
20SVPF120M
20
120
25
3200
12
480
16SVPF180M
16
180
22
3300
12
576
50SVPF18M
50
18
35
2700
12
180
35SVPF39M
35
39
30
2800
12
273
SVQP
25SVPF82M
25
82
28
3000
12
410
SVP
25SVPF100M
25
100
24
3200
12
500
20SVPF180M
20
180
25
3200
12
720
16SVPF270M
16
270
22
3300
12
864
50SVPF39M
50
39
25
3800
12
390
35SVPF82M
35
82
20
4000
12
574
25SVPF180M
25
180
16
4650
12
900
20SVPF390M
20
390
14
4950
12
1560
POSCAP
Line-up
16SVPF560M
16
560
14
4950
12
1792
Guidelines and
precautions
50SVPF68M
50
68
20
4300
12
680
35SVPF120M
35
120
18
4400
12
840
25SVPF330M
25
330
14
5000
12
1650
20SVPF560M
20
560
12
5400
12
2240
16SVPF1000M
16
1000
12
5400
12
3200
SVPF
Surface mount type
B6
Rated
voltage
(V)
Part number
Series system
diagram
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SXE
Radial lead type
Size
code
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Selection guide
Technical data
Recommended land pattern dimension of PWB
(unit : mm)
C
Size code
a
b
a
B6
1.4
C6
E7
b
c
7.4
1.6
2.1
9.1
1.6
2.8
11.1
1.9
E12
2.8
11.1
1.9
F12
4.3
13.1
1.9
Surface mount type
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Catalog Deletion and
EOL models
36
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
SXV
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Surface
mount type
SVPE
Series
Specifications
Items
Specifications
Condition
(V)
Rated voltage
(V)
Surge voltage
Category temperature range(℃)
−
2.0
2.5
6.3
10
16
Room temperature
2.6
3.3
8.2
12
18
−
−55 to ＋105
Capacitance tolerance (％)
120Hz/20℃
M : ±20
Dissipation Factor (DF)
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz/20℃
Please see the attached characteristics list
Leakage current※1
Equivalent series resistance (ESR)
Characteristics of impedance
ratio at high temp.
and low temp.
Based the value at
100kHz, ＋20℃
−55℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
LC
VPS (230℃ X 75s)
0.2max
Polarity marking
（Cathode）
Case No.
PE
Series
B6, C6, C10
size is PE
F12 size is SVPE
Rated capacitance
L
Size φD
code
R
（＋）
Rated voltage
Size list
μF
RV
2.0
RV : Rated voltage
2.5
16
C10
C6
B6
270
B6
330
B6,C6
390
470
10
B6
B6,C6
220
1200
6.3
B6
150
180
37
Within 1.3 times of the initial limit
Within the initial limit (after voltage processing)
(unit : mm)
W
P
C
003
Selection guide
Catalog Deletion and
EOL models
Within 1.3 times of the initial limit
ESR
Marking and dimensions
390
2.5
Surface mount type
Within ±10% of the initial value (±15% for 2.5V)
DF
※1 When measured values are questionable, measure after voltage processing mentioned below.
Voltage processing: Apply voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for reflow soldering conditions.
Guidelines and
precautions
Technical data
Within 1.5 times of the initial limit
Within the initial limit (after voltage processing)
LC
Catalog Deletion and
EOL series
POSCAP
Line-up
Within 1.5 times of the initial limit
DF
ESR
H
SEP
Resistance to soldering
heat※2
Within ±20% of the initial value
△C/C
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
Damp heat(Steady state)
φD
Radial lead type
SEPC
Within the initial limit
LC
△C/C
SEQP
Within 1.5 times of the initial limit
ESR
SVP
SEPF
Within 1.5 times of the initial limit
DF
105℃, 2,000h,
Rated voltage applied
Endurance
0.75 to 1.25
Z/Z20℃
＋105℃ Z/Z20℃
SVQP
SXE
RoHS directive/Halogen-free compliant
Super Low ESR（8mΩ∼ 18mΩ）
Large capacitance（1,200μF）
F12
C10
±0.5
L
＋0.1
−0.4
W ±0.2 H
±0.2
C
±0.2
R
P
±0.2
B6
5.0
5.9
5.3
5.3
6.0 0.6∼0.8
1.4
C6
6.3
5.9
6.6
6.6
7.3 0.6∼0.8
2.1
C10
6.3
9.9
6.6
6.6
7.3 0.6∼0.8
2.1
F12
10.0
12.6 10.3 10.3 11.0 0.8∼1.1
4.6
OS-CON
Line-up
B6
C10
F12
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
6SVPE150M
6.3
150
12
10
3520
12
500
6SVPE180M
6.3
180
15
13
3150
12
500
6SVPE220MW
6.3
220
15
13
3150
12
500
2R5SVPE270M
2.5
270
10
9
3860
12
500
2R5SVPE330M
2.5
330
15
13
3150
12
500
2R5SVPE330MY
2.5
330
10
9
3860
12
500
2R5SVPE390MX
2.5
390
10
9
3860
12
700
220
20
18
2700
12
500
10SVPE220M
C6
ESR(mΩ) (max)
100kHz/20℃ 300kHz/20℃※1
10
6SVPE220M
6.3
220
10
9
3900
12
500
2R5SVPE390M
2.5
390
10
9
3900
12
500
180
11
10
4460
12
576
8
8
5230
12
500
10
9
6100
12
1504
16SVPE180M
16
2SVPE1200M
2.0
16SVPE470M
1200
16
470
※1 The ESR value in 300kHz is a reference one.
Recommended land pattern dimension of PWB
Technical data
Rated
Rated
voltage capacitance
(μF)
(V)
Part number
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
Size
code
Series system
diagram
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
SXE
Radial lead type
SVPE series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
(unit : mm)
C
Size code
a
b
a
b
c
B6
1.4
7.4
1.6
C6
2.1
9.1
1.6
C10
2.1
9.1
1.6
F12
4.3
13.1
1.9
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Technical data
Surface mount type
Catalog Deletion and
EOL models
38
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVPS
Items
Condition
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
(V)
−
4.0
6.3
10
16
20
25
Surge voltage
(V)
Room temperature
5.2
8.2
12
18
23
25
Category temperature range (℃)
Capacitance tolerance
(％)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋105
−
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
Dissipation Factor (DF)
Based the value at
100kHz, ＋20℃
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
60℃, 90 to 95% RH,
1,000h,
No-applied voltage
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Resistance to soldering heat※2
0.75 to 1.25
−55℃ Z/Z20℃
105℃, 5,000h,
Rated voltage applied
(25V → 20V applied)
Endurance
Damp heat(Steady state)
SVQP
Specifications
Rated voltage
Equivalent series resistance (ESR)
SVPG
RoHS directive/Halogen-free compliant
Endurance： 105℃ 5,000h（Long life）
Specifications
Leakage current※1
SXV
Series
VPS (230℃ X 75s)
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 When measured values are questionable, measure after voltage processing mentioned below.
Voltage processing: Apply voltage for 120 minutes at 105℃. The voltage to be applied is the rated voltage for 4.0-20V products, and 20V for 25V products.
※2 Please refer to page 25 for reflow soldering conditions.
Marking and dimensions
POSCAP
Line-up
180
16
Selection guide
Series
B6,C6,E7,F8
size is SVPS
※A5 is S on the side
of rated capacitance
Rated capacitance
Rated voltage
μF
Catalog Deletion and
EOL models
39
R
（＋）
RV
10
15
22
33
39
47
68
82
100
120
150
180
220
270
330
470
680
±0.5
±0.2 H
L ＋0.1
−0.4 W
A5
B6
C6
E7
F8
6.3
A5
B6
C6
10
A5
A5
B6
C6
E7、F8
E7
F8
F8
16
C6
E7
F8
F8
R
P
±0.2
4.0
5.4
4.3
4.3
5.0 0.6∼0.8
1.0
5.0
5.9
5.3
5.3
6.0 0.6∼0.8
1.4
C6
6.3
5.9
6.6
6.6
7.3 0.6∼0.8
2.1
E7
8.0
6.9
8.3
8.3
9.0 0.6∼0.8
3.2
F8
10.0
7.9 10.3 10.3 11.0 0.6∼0.8
4.6
20
25
E7
B6
C
±0.2
A5
RV : Rated voltage
4.0
±0.2
B6
Size list
Technical data
Surface mount type
L
P
C
SVPS
Size φD
code
W
H
003
(unit : mm)
0.2max
Polarity marking
Case No.
（Cathode）
φD
Guidelines and
precautions
C6
E7
OS-CON
Line-up
B6
C6
E7
F8
Rated
capacitance
(μF)
Allowable
ESR(mΩ) (max)
ripple current
100kHz to 300kHz/20℃ 100kHz(mArms)※1
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
10SVPS10M
10
10
220
700
10
50
10SVPS15M
10
15
200
740
10
75
6SVPS22M
6.3
22
200
740
12
69.3
4SVPS33M
4.0
33
200
740
15
66
16SVPS22M
16
22
90
1060
10
176
10SVPS33M
10
33
70
1100
12
165
6SVPS47M
6.3
47
30
1970
12
300
4SVPS68M
4.0
68
30
1970
12
300
20SVPS22M
20
22
60
1450
10
88
16SVPS39M
16
39
24
2460
12
300
10SVPS68M
10
68
30
2200
12
300
6SVPS120M
6.3
120
22
2570
12
300
4SVPS150M
4.0
150
22
2570
12
300
25SVPS10M
25
10
60
1500
10
125
20SVPS47M
20
47
45
1890
12
188
16SVPS82M
16
82
30
2760
12
262
10SVPS150MX
10
150
30
2760
12
500
6SVPS220M
6.3
220
22
3220
12
500
4SVPS270M
4.0
270
22
3220
12
500
16SVPS100M
16
100
35
2670
12
320
16SVPS180M
16
180
29
3430
12
576
10SVPS150M
10
150
30
3020
12
300
10SVPS330M
10
330
24
3770
12
660
6SVPS470M
6.3
470
20
4130
12
592
4SVPS680M
4.0
680
20
4130
12
544
※1 The surface temperature of aluminum case top must not exceed 105℃. A rise in temperature due to self-heating by ripple current should
be factored in.
Recommended land pattern dimension of PWB
Technical data
A5
Rated
voltage
(V)
Part number
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
Size
code
Series system
diagram
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
SXE
Radial lead type
SVPS series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
（unit : mm）
C
Size code
a
b
a
b
c
A5
1.0
6.2
1.6
B6
1.4
7.4
1.6
C6
2.1
9.1
1.6
E7
2.8
11.1
1.9
F8
4.3
13.1
1.9
Technical data
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Surface mount type
Catalog Deletion and
EOL models
40
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVPD
Condition
Items
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
(V)
−
10
16
25
35
Surge voltage
(V)
125℃
12
18
29
40
Category temperature range (℃)
Characteristics of impedance
ratio at high temp.
and low temp.
Radial lead type
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
−55 to ＋125
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
Dissipation Factor (DF)
＋125℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 2 times of the initial limit
ESR
Within 2 times of the initial limit
85℃, 85 to 90%RH,
1,000h,
Rated voltage applied
Resistance to soldering heat※2
0.75 to 1.25
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
125℃, 2,000h,
Rated voltage applied
Endurance
SVP
SXE
−
(％)
Capacitance tolerance
Damp heat(Steady state)
SVQP
Specifications
Rated voltage
Equivalent series resistance (ESR)
SVPG
RoHS directive/Halogen-free compliant
Endurance： 125℃ 2,000h 35V max./Rated voltage
85℃ 85% guaranteed
Available for high reliability applications such as automotive, industrial equipments, etc.
Specifications
Leakage current※1
SXV
Series
VPS (230℃ X 75s)
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 2 times of the initial limit
ESR
Within 2 times of the initial limit
LC
Within the initial limit
△C/C
Within ±10% of the initial value
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125℃.
※2 Please refer to page 25 for reflow soldering conditions.
Marking and dimensions
POSCAP
Line-up
47
35
Selection guide
Series
C6 size is PD
E7,F8,E12,
F12size is SVPD
Rated capacitance
Rated voltage
Technical data
L
RV
10
16
F8
E7
22
Catalog Deletion and
EOL models
41
E12
F8
39
82
35
C6
18
56
25
E7
8.2
47
（＋）
RV : Rated voltage
10
Surface mount type
R
Size list
μF
P
C
SVPD
Size φD
code
W
H
003
(unit : mm)
0.2max
Polarity marking
（Cathode）
Case No.
φD
Guidelines and
precautions
E12
C6
E7
F12
F12
±0.5
L
＋0.1
−0.4
W ±0.2 H
±0.2
C
±0.2
R
P
±0.2
C6
6.3
5.9
6.6
6.6
7.3 0.6∼0.8
2.1
E7
8.0
6.9
8.3
8.3
9.0 0.6∼0.8
3.2
F8
10.0
7.9 10.3 10.3 11.0 0.6∼0.8
4.6
E12
8.0
F12
10.0
11.9
8.3
8.3
9.0 0.8∼1.1
3.2
12.6 10.3 10.3 11.0 0.8∼1.1
4.6
OS-CON
Line-up
C6
E7
F8
E12
F12
Rated
Rated
voltage capacitance
(μF)
(V)
Part number
ESR(mΩ) (max)
100kHz to 300kHz/20℃
Rated ripple current Allowable ripple current
100kHz（mArms）
105℃＜Tx≦125℃※1 Tx≦105℃※1
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
25SVPD10M
25
10
65
474
1500
10
50
10SVPD56M
10
56
45
538
1700
12
112
35SVPD8R2M
35
70
400
1300
10
57
25SVPD22M
25
22
48
580
1835
10
110
16SVPD82M
16
82
40
670
2120
12
262
8.2
Technical data
Size
code
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
SVPD series characteristics list
Selection guide
Guidelines and
precautions
SVPE
35SVPD18M
35
18
60
550
1800
10
126
25SVPD39M
25
39
45
664
2100
10
195
35SVPD22M
35
22
50
700
2300
12
154
25SVPD47M
25
47
30
943
2980
12
235
35SVPD47M
35
47
30
1150
3650
12
329
SVQP
25SVPD82M
25
82
28
1202
3800
12
410
SVP
Recommended land pattern dimension of PWB
C
a
b
a
b
SVPB
SVPA
SXE
c
C6
2.1
9.1
1.6
E7
2.8
11.1
1.9
F8
4.3
13.1
1.9
E12
2.8
11.1
1.9
F12
4.3
13.1
1.9
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
（unit : mm）
Size code
SVPC
Radial lead type
※1 Tx : Ambient temperature
SVPS
SVPD
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Technical data
Surface mount type
Catalog Deletion and
EOL models
42
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVPC
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Items
Condition
Specifications
(V)
−
2.5
4.0
6.3
10
16
Surge voltage
(V)
Room temperature
3.3
5.2
8.2
12
18
Category temperature range (℃)
Capacitance tolerance
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz/20℃
Please see the attached characteristics list
(％)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋105
−
Dissipation Factor (DF)
Based the value at
100kHz, ＋20℃
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Resistance to soldering heat※2
0.75 to 1.25
−55℃ Z/Z20℃
105℃, 2,000h,
Rated voltage applied
Endurance
Damp heat(Steady state)
SVQP
RoHS directive/Halogen-free compliant
Low ESR（9mΩ∼ 30mΩ）
Large capacitance（2,700μF）
Rated voltage
Equivalent series resistance (ESR)
SVPG
Series
Specifications
Leakage current※1
SXV
Update
VPS (230℃ X 75s)
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value (±15% for 2.5V 4.0V)
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for reflow soldering conditions.
Catalog Deletion and
EOL series
Marking and dimensions
POSCAP
Line-up
120
16
Selection guide
B6, C6 size is
PC, E7, E12, F12
size is SVPC
Rated capacitance
L
Rated voltage
Technical data
Catalog Deletion and
EOL models
43
R
（＋）
Size list
μF
Surface mount type
P
C
SVPC
Size φD
code
W
H
003
(unit : mm)
0.2max
Polarity marking
Case No.
（Cathode）
Series
φD
Guidelines and
precautions
RV
39
68
100
120
150
180
220
270
330
390
560
680
820
1,200
1,500
2,700
B6
C6
C6
E7
E12
E12
F12
4.0
B6
6.3
B6
B6
C6
C6
E7、E12
E12
E12
C6
E7
E12
10
B6
C6
E7
E7
L
W ±0.2 H
±0.2
C
±0.2
R
P
±0.2
B6
5.0
5.9
5.3
5.3
6.0 0.6∼0.8 1.4
C6
6.3
5.9
6.6
6.6
7.3 0.6∼0.8 2.1
E7
8.0
6.9
8.3
8.3
9.0 0.6∼0.8 3.2
E12
8.0
11.9
8.3
8.3
9.0 0.8∼1.1 3.2
F12
10.0
RV : Rated voltage
2.5
±0.5
＋0.1
−0.4
16
B6
C6
C6
E7
E7
E12
12.6 10.3 10.3 11.0 0.8∼1.1 4.6
OS-CON
Line-up
16SVPC39M
16
39
10SVPC68M
10
68
6SVPC100M
B6
6SVPC120MV
16
16SVPC100M
16
100
10
120
120
10
10SVPC120M
10SVPC120MV
16SVPC120M
16
10SVPC270M
10
4.0
4SVPC560MX
4.0
4SVPC1200M
4.0
4SVPC1500M
2.5
2R5SVPC820M
2.5
2R5SVPC1500M
2.5
2R5SVPC2700M
1200
12
10
820
9
8
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
500
15
750
15
5070
SVPF
SVPE
1200
15
5150
SXV
SVPG
960
15
5380
10
12
2700
500
15
4700
9
10
1500
1033
15
4700
10
12
1500
Reliability
864
15
5380
Characteristics
500
15
4700
8
9
560
500
12
4070
10
12
820
6.3
6SVPC820M
491
12
3370
14
660
12
3220
17
16
270
16
16SVPC270M
20
680
2.5
2R5SVPC680M
500
12
3220
Fundamental
structure
500
12
3460
19
500
12
3220
19
22
560
4.0
4SVPC560M
22
390
6.3
6SVPC390M
300
12
3220
17
19
330
10
10SVPC330M
300
12
2900
19
22
270
300
12
3500
21
22
150
300
12
3160
23
27
120
16
16SVPC150M
300
12
2410
14
300
12
3160
Recommended
soldering
condition
415
12
2630
Packing
specifications
（Radial lead type）
300
12
2320
Products list
Packing
specifications
（SMD type）
300
12
3390
13
16
560
2.5
2R5SVPC560M
15
390
2.5
2R5SVPC390MV
300
12
3160
22
25
390
2.5
2R5SVPC390M
300
12
2320
13
15
330
4.0
4SVPC330MV
21
330
4.0
4SVPC330MY
300
12
2600
18
300
12
2320
23
27
330
4.0
4SVPC330M
300
12
2490
15
300
12
2440
13
17
330
6.3
6SVPC330M
15
220
6.3
6SVPC220MV
300
12
2200
23
27
220
6.3
6SVPC220M
300
12
2800
Image of
case size
300
12
2200
Series system
diagram
300
12
1970
19
22
300
12
2730
23
27
300
12
2240
23
24
300
12
1970
22
25
68
16
16SVPC68MV
300
12
2660
26
30
300
12
2150
16
19
68
16SVPC68M
300
12
1970
20
24
12
2540
26
30
180
2.5
2R5SVPC180MV
300
17
20
180
2.5
12
20
23
180
1970
2350
26
30
150
26
18
21
150
300
21
25
150
2.5
2R5SVPC180MY
F12
120
4.0
2R5SVPC180M
E12
6.3
12
26
30
Leakage current
(μA)(max)
After 2 minutes
1820
20
23
100
4.0
4SVPC150MV
E7
100
4.0
4SVPC150M
4SVPC150MY
C6
6.3
6.3
6SVPC100MY
30
DF
(% max)
30
23
27
68
10
10SVPC68MV
35
39
16
16SVPC39MV
100kHz/20℃
Rated
ripple current
300kHz/20℃※1 100kHz (mArms) at 105℃
Technical data
Part number
ESR (mΩ) (max)
Surface mount type
Rated
Rated
voltage capacitance
(V)
(μF)
Radial lead type
Size
code
Selection guide
Guidelines and
precautions
SVPC series characteristics list
1350
Technical data
※1 The ESR value in 300kHz is a reference one.
Recommended land pattern dimension of PWB
（unit : mm）
Size code
C
B6
C6
a
E7
b
E12
F12
a
b
1.4
c
7.4
1.6
2.1
9.1
1.6
2.8
11.1
1.9
2.8
11.1
1.9
4.3
13.1
1.9
Surface mount type
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
※ Red letters ： New models
Catalog Deletion and
EOL models
44
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVPB
Items
Condition
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
Specifications
Rated voltage
(V)
−
2.5
4.0
6.3
10
16
20
Surge voltage
(V)
Room temperature
3.3
5.2
8.2
12
18
23
Category temperature range (℃)
Capacitance tolerance
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋105
−
Dissipation Factor (DF)
Equivalent series resistance (ESR)
SVPG
Based the value at
100kHz, ＋20℃
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value(±30% for C5 size)
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
105℃, 1,000h,
Rated voltage applied
Endurance
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
Damp heat(Steady state)
Radial lead type
SEPF
SEPC
SEQP
SEP
Resistance to soldering heat※2
0.75 to 1.25
−55℃ Z/Z20℃
SVP
SXE
RoHS directive/Halogen-free compliant
Low profile/5mm height, 5.5mm height
Specifications
Leakage current※1
SXV
Series
VPS (230℃ X 75s)
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value (±20% for C5 size)
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125℃.
※2 Please refer to page 25 for reflow soldering conditions.
Catalog Deletion and
EOL series
Marking and dimensions
0.2max
Polarity marking
（Cathode）
Case No.
PB
56
10
Selection guide
(unit : mm)
Series
(PB)
P
C
003
W
H
Guidelines and
precautions
φD
POSCAP
Line-up
Rated capacitance
Rated voltage
L
R
μF
RV
2.5
4.0
6.3
10
120
C5
±0.2
6.6
6.6
7.3 0.6∼0.8
2.1
6.6
6.6
7.3 0.6∼0.8
2.1
16
C5
C5
P
5.4
20
C5
C5
R
4.9
C55
82
C
±0.2
6.3
22
100
H
±0.2
6.3
15
C5
W
±0.2
C5
RV : Rated voltage
56
45
L
＋0.1
−0.4
（＋）
33
Catalog Deletion and
EOL models
±0.5
C55
Size list
Technical data
Surface mount type
Size φD
code
OS-CON
Line-up
C5
C55
Rated
Rated
voltage capacitance
(μF)
(V)
Part number
ESR (mΩ) (max)
100kHz to 300kHz/20℃
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
20SVPB15M
20
15
45
2000
12
120
16SVPB33M
16
33
40
1670
12
211
10SVPB56M
10
56
40
1670
12
224
6SVPB82M
6.3
82
40
1670
12
207
4SVPB100M
4.0
100
40
1670
12
160
2R5SVPB120M
2.5
120
40
1670
12
120
22
35
2000
12
88
20SVPB22M
20
Recommended land pattern dimension of PWB
Technical data
Size
code
Series system
diagram
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
SVPB series characteristics list
Selection guide
Guidelines and
precautions
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
Size code
a
b
a
b
c
C5
2.1
9.1
1.6
C55
2.1
9.1
1.6
SXE
Radial lead type
C
（unit : mm）
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Technical data
Surface mount type
Catalog Deletion and
EOL models
46
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVPA
Items
Condition
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
(V)
−
2.5
4.0
6.3
10
16
20
Surge voltage
(V)
Room temperature
3.3
5.2
8.2
12
18
23
Category temperature range (℃)
Capacitance tolerance
−55 to ＋105
−
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz/20℃
Please see the attached characteristics list
(％)
Dissipation Factor (DF)
Characteristics of impedance
ratio at high temp.
and low temp.
Based the value at
100kHz, ＋20℃
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
VPS (230℃ X 75s)
Resistance to soldering heat※2
0.75 to 1.25
−55℃ Z/Z20℃
105℃, 2,000h,
Rated voltage applied
Endurance
Damp heat(Steady state)
SVQP
Specifications
Rated voltage
Equivalent series resistance (ESR)
SVPG
RoHS directive/Halogen-free compliant
Low ESR 18mΩ
High rated ripple current（4,240mArms）
Specifications
Leakage current※1
SXV
Series
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for reflow soldering conditions.
Catalog Deletion and
EOL series
Marking and dimensions
47
20
Selection guide
Catalog Deletion and
EOL models
47
Size
φD
code
Series
B6, C6 size is
PA, E7, F8
size is
Rated capacitance
Rated voltage
L
R
（＋）
RV
10
22
39
47
68
82
120
150
180
220
270
330
470
680
820
±0.5
±0.2 H
L ＋0.1
−0.4 W
B6
C6
E7
F8
4.0
B6
C6
E7
F8
6.3
B6
C6
10
E7
E7
F8
F8
R
P
±0.2
5.0
5.9
5.3
5.3
6.0 0.6∼0.8
1.4
6.3
5.9
6.6
6.6
7.3 0.6∼0.8
2.1
E7
8.0
6.9
8.3
8.3
9.0 0.6∼0.8
3.2
F8
10.0
7.9 10.3 10.3 11.0 0.6∼0.8
4.6
16
C6
C6
C
±0.2
B6
RV : Rated voltage
2.5
±0.2
C6
Size list
μF
Surface mount type
(unit : mm)
W
P
C
003
SVPA
Technical data
0.2max
Polarity marking
（Cathode）
Case No.
H
Guidelines and
precautions
φD
POSCAP
Line-up
E7
F8
20
B6
C6
E7
OS-CON
Line-up
20SVPA10M
B6
C6
E7
F8
20
ESR (mΩ) (max)
100kHz/20℃ 300kHz/20℃※1
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
10
40
35
1700
12
80
6SVPA47MAA
6.3
47
30
26
1970
12
300
4SVPA68MAA
4.0
68
30
26
1970
12
300
2R5SVPA82MAA
2.5
82
30
26
1970
12
300
20SVPA22M
20
22
35
31
2040
12
88
16SVPA39MAA
16
39
35
31
2040
12
300
16SVPA39MAAY
16
39
24
20
2460
12
300
10SVPA68MAA
10
68
30
26
2200
12
300
Technical data
Rated
Rated
voltage capacitance
(V)
(μF)
Part number
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
SVPE
SVPS
SVPD
SVPC
6SVPA120MAA
6.3
120
22
19
2570
12
300
4SVPA150MAA
4.0
150
22
19
2570
12
300
2R5SVPA180MAA
2.5
180
20
18
2690
12
300
SVQP
SVP
20SVPA47M
20
47
33
29
2630
12
188
16SVPA82MAA
16
82
30
25
2760
12
262
10SVPA150MAA
10
150
30
25
2760
12
500
6SVPA220MAA
6.3
220
22
19
3220
12
500
4SVPA270MAA
4.0
270
22
19
3220
12
500
2R5SVPA330MAA
2.5
330
20
18
3370
12
500
SVPB
SVPA
SXE
Radial lead type
Size
code
Series system
diagram
Surface mount type
SVPA series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
16SVPA180M
16
180
29
28
3430
12
576
10SVPA330M
10
330
24
23
3770
12
660
POSCAP
Line-up
Guidelines and
precautions
6SVPA470M
6.3
470
20
19
4130
12
592
4SVPA680M
4.0
680
20
19
4130
12
544
2R5SVPA820M
2.5
820
19
18
4240
12
500
Selection guide
※1 The ESR value at 300kHz is a reference one.
Recommended land pattern dimension of PWB
Technical data
（unit : mm）
C
Size code
a
b
a
B6
1.4
C6
E7
F8
b
c
7.4
1.6
2.1
9.1
1.6
2.8
11.1
1.9
4.3
13.1
1.9
Surface mount type
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Catalog Deletion and
EOL models
48
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVQP
Series
Specifications
Items
Condition
(V)
−
4.0
6.3
10
16
20
Surge voltage
(V)
Room temperature
5.2
8.2
12
18
23
Category temperature range (℃)
Capacitance tolerance
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋125
−
Dissipation Factor (DF)
Equivalent series resistance (ESR)
SVPG
Based the value at
100kHz, ＋20℃
＋125℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 2 times of the initial limit
ESR
Within 2 times of the initial limit
125℃, 1,000h,
Rated voltage applied
Endurance
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
Damp heat(Steady state)
Radial lead type
SEPF
SEPC
SEQP
SEP
Resistance to soldering heat※2
0.75 to 1.25
−55℃ Z/Z20℃
SVP
SXE
Specifications
Rated voltage
Leakage current※1
SXV
RoHS directive/Halogen-free compliant
Endurance： 125℃ 1,000h
VPS (230℃ X 75s)
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125℃.
※2 Please refer to page 25 for reflow soldering conditions.
Catalog Deletion and
EOL series
Marking and dimensions
0.2max
Polarity marking
（Cathode）
Case No.
QP
22
20
Selection guide
(unit : mm)
Size
code φD
Series
(QP)
Rated capacitance
Rated voltage
L
P
C
003
W
H
Guidelines and
precautions
φD
POSCAP
Line-up
R
μF
RV
6.3
10
16
22
Surface mount type
82
C6
100
C6
120
150
220
Catalog Deletion and
EOL models
49
C6
E7
E7
C6
E7
E7
±0.2
R
P
±0.2
5.9
6.6
6.6
7.3 0.6∼0.8
2.1
6.9
8.3
8.3
9.0 0.6∼0.8
3.2
20
E7
56
C
8.0
C6
47
±0.2
6.3
C6
39
W ±0.2 H
E7
RV : Rated voltage
4.0
L
C6
（＋）
Size list
Technical data
±0.5
＋0.1
−0.4
OS-CON
Line-up
C6
Part number
Rated
Rated
voltage capacitance
(μF)
(V)
Rated ripple current Allowable ripple current
100kHz（mArms）
105℃＜Tx≦125℃※1 Tx≦105℃※1
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
20SVQP22M
20
22
60
459
1450
10
220
16SVQP39M
16
39
50
512
1620
10
312
10SVQP56M
10
56
45
538
1700
12
280
6SVQP82M
6.3
82
45
538
1700
12
258
6SVQP100M
6.3
100
40
572
1810
12
315
4SVQP150M
E7
ESR(mΩ) (max)
100kHz to 300kHz/20℃
4.0
150
40
572
1810
12
300
20SVQP47M
20
47
45
598
1890
12
470
16SVQP82M
16
82
40
670
2120
12
656
10SVQP120M
10
120
35
810
2560
12
600
10SVQP150M
10
150
35
810
2560
12
750
220
35
810
2560
12
693
6SVQP220M
6.3
Recommended land pattern dimension of PWB
C
a
b
a
b
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
（unit : mm）
Size code
Image of
case size
Radial lead type
※1 Tx : Ambient temperature
Technical data
Size
code
Series system
diagram
Surface mount type
SVQP series characteristics list
Selection guide
Guidelines and
precautions
c
C6
2.1
9.1
1.6
E7
2.8
11.1
1.9
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Technical data
Surface mount type
Catalog Deletion and
EOL models
50
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Surface
mount type
SVP
Items
Condition
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
(V)
−
2.5
4.0
6.3
10
16
20
Surge voltage
(V)
Room temperature
3.3
5.2
8.2
12
18
23
Category temperature range (℃)
Capacitance tolerance
−55 to ＋105
−
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Dissipation Factor (DF)
Characteristics of impedance
ratio at high temp.
and low temp.
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
60℃, 90 to 95%RH,
1,000h,
No applied voltage
SVP
SEQP
SEP
Guidelines and
precautions
0.2max
Polarity marking
（Cathode）
Case No.
003
82
16
Within 1.5 times of the initial limit
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±10% of the initial value
DF
Within 1.3 times of the initial limit
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
3.3
4.7
6.8
10
15
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
470
560
680
820
1,200
1,500
W
Rated capacitance
L
R
Size list
μF
Size
code φD
Series
A5, B6, C6 size
has no marking
E7,F8,E12,F12
size is SVP
Rated voltage
Technical data
51
DF
ESR
(unit : mm)
Selection guide
Catalog Deletion and
EOL models
Within ±20% of the initial value
Marking and dimensions
SVP
Surface mount type
Within the initial limit
△C/C
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for reflow soldering conditions.
Catalog Deletion and
EOL series
POSCAP
Line-up
VPS (230℃ X 75s)
LC
P
C
SEPC
Resistance to soldering heat※2
H
SEPF
φD
Radial lead type
SXE
0.75 to 1.25
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
105℃, 2,000h,
Rated voltage applied
Endurance
Damp heat(Steady state)
SVQP
Specifications
Rated voltage
Equivalent series resistance (ESR)
SVPG
RoHS directive/Halogen-free compliant
Standard of Surface Mount Type
Wealth of models
Specifications
Leakage current※1
SXV
Series
RV
（＋）
RV : Rated voltage
2.5
4.0
6.3
A5
A5
B6
B6
C6
E7
E12
F12
E12
F8
F12
A5
A5
A5
A5
B6
B6
C6
C6
C6
E7, F8
C6
10
C6
C6
E7
E7, F8
F8
F8
F8, E12
F8, E12
F12
F12
16
20
A5
B6
C6
E7
F8
E12
F12
±0.5
4.0
5.0
6.3
8.0
10.0
8.0
10.0
L
＋0.1
−0.4
W ±0.2 H
±0.2
C
±0.2
R
P
5.0 0.6∼0.8
4.3
4.3
5.4
6.0 0.6∼0.8
5.3
5.3
5.9
7.3 0.6∼0.8
6.6
6.6
5.9
9.0 0.6∼0.8
8.3
8.3
6.9
7.9 10.3 10.3 11.0 0.6∼0.8
9.0 0.8∼1.1
8.3
8.3
11.9
12.6 10.3 10.3 11.0 0.8∼1.1
±0.2
1.0
1.4
2.1
3.2
4.6
3.2
4.6
Recommended land pattern
dimension of PWB
A5
B6
B6
C6
E7
E7
F8
F8
F8, E12
F12
B6
C
OS-CON
Line-up
C6
C6
E7
E7
F8
F8
E12
F12
a
b
（unit : mm）
Size code
a
b
c
A5
1.0
6.2
1.6
1.4
7.4
1.6
2.1
9.1
1.6
2.8
11.1
1.9
4.3
13.1
1.9
2.8
11.1
1.9
4.3
13.1
1.9
B6
C6
E7
F8
E12
F12
OS-CON
Line-up
B6
C6
E7
F8
E12
F12
16SVP3R3M
10SVP4R7M
10SVP6R8M
10SVP10M
10SVP15M
6SVP22M
4SVP33M
20SVP10M
16SVP15M
16SVP22M
10SVP33M
6SVP47M
4SVP39M
4SVP68M
20SVP22M
20SVP27M
16SVP39M
10SVP47M
10SVP56M
6SVP82M
6SVP100M
6SVP120MV
4SVP150MX
2R5SVP220M
20SVP33M
20SVP47M
16SVP56M
16SVP82M
10SVP120M
10SVP150MX
6SVP220MX
4SVP330M
20SVP56M
20SVP68M
16SVP100M
16SVP150M
16SVP180MX
10SVP150M
10SVP270M
10SVP330MX
6SVP220M
6SVP330M
6SVP470MX
4SVP680M
20SVP100M
16SVP180M
10SVP330M
6SVP470M
4SVP560M
2R5SVP680M
20SVP150M
16SVP330M
10SVP560M
6SVP820M
4SVP1200M
2R5SVP1500M
Rated
voltage
(V)
Rated
capacitance
(μF)
ESR(mΩ) (max)
100kHz to 300kHz/20℃
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
16
10
10
10
10
6.3
4.0
20
16
16
10
6.3
4.0
4.0
20
20
16
10
10
6.3
6.3
6.3
4.0
2.5
20
20
16
16
10
10
6.3
4.0
20
20
16
16
16
10
10
10
6.3
6.3
6.3
4.0
20
16
10
6.3
4.0
2.5
20
16
10
6.3
4.0
2.5
3.3
4.7
6.8
10
15
22
33
10
15
22
33
47
39
68
22
27
39
47
56
82
100
120
150
220
33
47
56
82
120
150
220
330
56
68
100
150
180
150
270
330
220
330
470
680
100
180
330
470
560
680
150
330
560
820
1200
1500
260
240
240
220
200
200
200
120
120
90
70
70
70
60
60
60
50
50
45
45
40
17
40
23
45
45
45
40
35
35
35
35
40
40
35
30
30
30
25
25
25
25
25
25
24
20
17
15
13
13
20
16
13
12
12
12
660
670
670
700
740
740
740
1020
1020
1060
1100
1100
1100
1400
1450
1450
1620
1620
1700
1700
1810
2780
1810
2390
1890
1890
1890
2120
2560
2560
2560
2560
2400
2400
2670
3020
3020
3020
3700
3700
3700
3700
3700
3700
3320
3640
3950
4210
4520
4520
4320
4720
5230
5440
5440
5440
7.0
8.0
9.0
10
10
12
15
10
10
10
12
12
12
12
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
15
15
15
15
15
15
15
15
15
15
18
18
Leakage current
(μA)(max)
After 2 minutes
26.4
23.5
34
50
75
69.3
66
100
120
176
165
148
78
136
88
108
125
94
112
103
126
151
120
110
132
188
179
262
240
300
277
264
224
272
320
480
576
300
540
660
277
416
592
544
400
576
660
592
448
340
600
792
840
775
960
750
Technical data
A5
Part number
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
Surface mount type
Size
code
Series system
diagram
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
SVP
SXE
Radial lead type
SVP series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Technical data
Surface mount type
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Catalog Deletion and
EOL models
52
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Radial lead
type
SXE
Items
Condition
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
−
63
Surge voltage
（V）
−
72.5
Category temperature range（℃）
−
Capacitance tolerance
（％）
Characteristics of impedance
ratio at high temp.
and low temp.
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
Z/Z20℃
＋105℃
Z/Z20℃
0.75 to 1.25
0.75 to 1.25
△C/C
Within ±20% of the initial value
tanδ
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit
△C/C
Within ±20% of the initial value
tanδ
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±5% of the initial value
tanδ
Within 1.3 times of the initial limit
Flow method
(260±5℃ X 10s)
Resistance to soldering heat※2
ESR
Within 1.3 times of the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for reflow soldering conditions.
Marking and dimensions
POSCAP
Line-up
Guidelines and
precautions
−55℃
227
SXE
33
63
Selection guide
Series
(SXE)
15min.
Rated capacitance
L
Rated voltage
Size list
Technical data
μF
RV
Size
code
（＋）
φD
E12
±0.5
8.0
L max
F
φd ±0.05
12.0
3.5±0.3
0.6
4min.
19min.
RV : Rated voltage
63
15
33
(unit : mm)
φd
Polarity marking
（Cathode）
Case No.
φD
Radial lead type
SEPF
Based the value at
100kHz, ＋20℃
60℃, 90 to 95%RH,
1,000h,
No applied voltage
SVP
115.0
−55 to ＋105
105℃, 5,000h,
Rated voltage applied
Endurance
100
120Hz/20℃
Dissipation Factor (DF)
Damp heat(Steady state)
SXE
Specifications
（V）
F
Surface mount type
SVPF
RoHS directive/Halogen-free compliant
Super high voltage（100V）
Endurance： 105℃ 5,000h
Rated voltage
Equivalent series resistance (ESR)
SVPG
Series
Specifications
Leakage current※1
SXV
NEW
100
E12
E12
SXE series characteristics list
Surface mount type
Size
code
E12
Part number
Rated
voltage
(V)
63SXE33M
100SXE15M
Rated
capacitance
(μF)
ESR(mΩ) (max)
100kHz to 300kHz/20℃
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
63
33
25
2950
12
104
100
15
40
2350
12
75
Frequency coefficient for ripple current
Catalog Deletion and
EOL models
53
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
SEPF
Series
OS-CON
Line-up
RoHS directive/Halogen-free compliant
High voltage（35V）
Large capacitance（1,000μF）
Endurance： 105℃ 5,000h
Guidelines and
precautions
Specifications
Surge voltage
(V)
−
(％)
Dissipation Factor (DF)
Equivalent series resistance (ESR)
−55 to ＋105
32
35
37
40
0.75 to 1.25
LC
Within the initial limit
Within ±20% of the initial value
Within 1.5 times of the initial limit
DF
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
DF
Within the initial limit
Within ±5% of the initial value
Within the initial limit
ESR
Within the initial limit (after voltage processing)
LC
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SVPG
Within 1.5 times of the initial limit
△C/C
Flow method
(260±5℃ X 10s)
Packing
specifications
（Radial lead type）
SXV
Within 1.5 times of the initial limit
△C/C
Products list
Packing
specifications
（SMD type）
0.75 to 1.25
DF
ESR
Image of
case size
Within ±20% of the initial value
ESR
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
Resistance to soldering heat※2
29
Please see the attached characteristics list
△C/C
Damp heat(Steady state)
25
Please see the attached characteristics list
100kHz to 300kHz/20℃
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
＋105℃ Z/Z20℃
105℃, 5,000h,
Rated voltage applied
Endurance
23
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Characteristics of impedance
ratio at high temp.
and low temp.
Specifications
M : ±20
120Hz/20℃
120Hz/20℃
Leakage current※1
20
18
Room temperature
Category temperature range (℃)
Capacitance tolerance
16
−
Technical data
Condition
(V)
Series system
diagram
SVPF
Surface mount type
Items
Rated voltage
Selection guide
Radial lead
type
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for flow soldering conditions.
68
32
(SEPF)
（＋）
F
φD
SEPF
μF
15min.
Rated capacitance
Rated voltage
L
4min.
19min.
(unit : mm)
Size
code
φD
±0.5
6.3
6.3
8.0
8.0
10.0
C55
C6
E7
E12
F13
L max
F
φd ±0.05
5.5
6.0
7.0
12.0
13.0
2.5±0.5
2.5±0.5
3.5±0.5
3.5±0.5
5.0±0.5
0.45
0.5
0.5 ※
0.6
0.6
※3 32SEPF68M is 0.6±0.05
RV
22
39
56
68
82
120
150
180
270
330
390
560
1,000
16
RV : Rated voltage
20
25
C6
C55
C6
E7
E12
F13
C6
E7
E12
F13
E7
32
35
C55
C6
E7
E7
E12
F13
Ｃ55
C6
E7
E12
F13
Part number
32SEPF22M
16SEPF150M
35SEPF22M
25SEPF56M
20SEPF120M
16SEPF180M
35SEPF39M
32SEPF68M
25SEPF82M
20SEPF180M
16SEPF270M
35SEPF82M
25SEPF180M
20SEPF390M
16SEPF560M
35SEPF120M
25SEPF330M
20SEPF560M
16SEPF1000M
Rated
voltage
(V)
32
16
35
25
20
16
35
32
25
20
16
35
25
20
16
35
25
20
16
Rated
capacitance
(μF)
22
150
22
56
120
180
39
68
82
180
270
82
180
390
560
120
330
560
1000
Coefficient
120Hz≦ f ＜1kHz
0.05
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
F13
Guidelines and
precautions
Selection guide
Rated
ESR(mΩ) (max) ripple
current
100kHz to 300kHz/20℃ 100kHz (mArms) at 105℃
35
30
35
30
25
22
30
25
28
25
22
20
16
14
14
18
14
12
12
Frequency coefficient for ripple current
Frequency
SEPF
E12
SEPF series characteristics list
Size
code
SXE
Radial lead type
φd
Polarity marking
（Cathode）
Case No.
223
SVP
Size list
Marking and dimensions
Series
SVQP
1kHz≦ f ＜10kHz
0.3
2400
2590
2600
2800
3200
3300
2800
3200
3000
3200
3300
4000
4650
4950
4950
4400
5000
5400
5400
10kHz≦ f ＜100kHz
0.7
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
12
12
12
12
12
12
12
10
12
12
12
12
12
12
12
12
12
12
12
140
480
154
280
480
576
273
435
410
720
864
574
900
1560
1792
840
1650
2240
3200
100kHz≦ f ≦500kHz
1
Technical data
Surface mount type
Catalog Deletion and
EOL models
54
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Radial lead
type
SEPC
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Items
Condition
Specifications
(V)
−
2.5
4.0
6.3
10
16
Surge voltage
(V)
Room temperature
3.3
5.2
8.2
12
18
Category temperature range (℃)
Capacitance tolerance
−55 to ＋105
−
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Dissipation Factor (DF)
Characteristics of impedance
ratio at high temp.
and low temp.
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
105℃, 5,000h,
Rated voltage applied
Endurance
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
SVP
SEPF
SEPC
SEQP
SEP
Flow method
(260±5℃ X 10s)
Resistance to soldering heat※2
LC
Within the initial limit
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±5% of the initial value
DF
Within the initial limit
ESR
Within the initial limit
LC
Within the initial limit (after voltage processing)
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105℃.
※2 Please refer to page 25 for flow soldering conditions.
Marking and dimensions
Catalog Deletion and
EOL series
E12, E13, F13 Size
POSCAP
Line-up
003
Guidelines and
precautions
2700
2.5
SEPC
Series
SEPC
φd
(unit : mm)
（＋）
φD
Polarity marking
（Cathode）
Case No.
F
Radial lead type
SXE
0.75 to 1.25
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
Damp heat(Steady state)
SVQP
RoHS directive/Halogen-free compliant
Super Low ESR（5mΩ∼ 24mΩ）
Large capacitance（2,700μF）
Endurance： 105℃ 5,000h
Rated voltage
Equivalent series resistance (ESR)
SVPG
Series
Specifications
Leakage current※1
SXV
Update
has
(B9no size
marking )
15min.
Rated capacitance
L
Rated voltage
4min.
19min.
B9, C55, C6, C7, C9, E7, E9 Size
φd
（＋）
F
φD
Selection guide
15min.
Technical data
L
4min.
19min.
B9,C55,C6,C7,C9,E7,E9 size flat rubber is used.
Size list
μF
Surface mount type
Catalog Deletion and
EOL models
55
RV
100
150
180
220
270
330
390
470
560
680
820
1,000
1,500
2,700
2.5
RV : Rated voltage
4.0
6.3
10
16
E7
C6，C9
E7
E9, E12
E7
E9, E12
B9
C55
B9, C9
C6
B9
C7,C9, E9, E13
B9, C6,C9, E9 C9, E9, E13 C9, E9
F13
E13
F13
C9,E7, E9, E13
E7
E9
F13
F13
F13
Size
code
φD
±0.5
L max
B9
5.0
9.0
C55
6.3
5.5
C6
6.3
6.0
C7
6.3
7.0
C9
6.3
9.0
E7
8.0
7.0
E9
8.0
9.0
E12
8.0
12.0
E13
8.0
13.0
F13
10.0
13.0
F
φd ±0.05
2.0±0.5 0.6
2.5±0.5 0.45
2.5±0.5 0.45 ※3
2.5±0.5 0.6
2.5±0.5 0.6
3.5±0.5 0.6 ※4
3.5±0.5 0.6
3.5±0.5 0.6
3.5±0.5 0.6
5.0±0.5 0.6
※3 2SEPC390M, 2SEPC560M : 0.5±0.05
※4 16SEPC150MD,10SEPC270MD : 0.45±0.05
OS-CON
Line-up
C55
Rated
voltage
(V)
C7
7
4180
10
500
2SEPC330MZ
2.5
330
7
4180
10
500
2SEPC470MZ
2.5
470
7
4180
10
500
2SEPC560MZ
2.5
560
7
4180
10
500
6SEPC220M
6.3
220
18
2980
12
280
100
24
2490
10
320
16
2SEPC390M
2.5
390
10
3900
12
500
2SEPC560M
2.5
560
10
3900
12
500
6SEPC470ME
6.3
470
20
2970
10
592
16
100
10
4680
10
500
6SEPC470MW
6.3
470
7
5600
10
592
6SEPC560MW
6.3
560
7
5600
10
705
E12
E13
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
4SEPC560MW
4.0
560
7
5600
10
500
2SEPC330MW
2.5
330
7
5600
10
500
SVP
2SEPC560MW
2.5
560
7
5600
10
500
2.5
820
7
5600
10
500
16SEPC150MD
16
150
22
3220
12
500
16SEPC220MD
16
220
13
4150
10
500
10SEPC270MD
10
270
22
3220
12
500
820
8
5300
10
500
2.5
6SEPC1000MD
6.3
1000
18
3530
10
1260
16SEPC180MX
16
180
10
5000
10
576
16SEPC270MX
16
270
10
5000
10
864
6SEPC470MX
6.3
470
8
5700
10
592
6SEPC560MX
6.3
560
7
6100
10
705
4SEPC560MX
4.0
560
7
6100
10
500
2SEPC560MX
2.5
560
8
4700
10
280
2SEPC820MX
2.5
820
7
6100
10
500
2SEPC820MY
2.5
820
5
7200
10
500
2SEPC1000MX
2.5
1000
7
6100
10
500
16SEPC180M
16
180
16
4360
10
576
16SEPC270M
16
270
11
5000
10
864
6SEPC470M
6.3
470
8
5700
10
592
4SEPC560M
4.0
560
7
6100
10
500
4SEPC680M
4.0
680
7
6100
10
544
2.5
820
7
6100
10
500
470
10
6100
10
1504
2R5SEPC820M
16SEPC470M
F13
Products list
Packing
specifications
（SMD type）
SVQP
2SEPC820MD
E9
Leakage current
(μA)(max)
After 2 minutes
100
2SEPC820MW
E7
DF
(% max)
2.5
16SEPC100MW
C9
Rated
ESR(mΩ) (max)
ripple current
100kHz to 300kHz/20℃ 100kHz (mArms) at 105℃
2SEPC100MZ
16SEPC100M
C6
Rated
capacitance
(μF)
Technical data
B9
Part number
Image of
case size
16
6SEPC680M
6.3
680
7
6640
10
857
6SEPC1500M
6.3
1500
10
5560
10
1890
4SEPC820M
4.0
820
7
6640
10
656
2SEPC2700M
2.5
2700
10
5560
10
1350
SXE
Radial lead type
Size
code
Series system
diagram
Surface mount type
SEPC series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Technical data
Surface mount type
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
※ Red letters ： New models
Catalog Deletion and
EOL models
56
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Radial lead
type
SEQP
Items
Condition
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
(V)
−
4.0
6.3
10
16
20
32
Surge voltage
(V)
Room temperature
5.2
8.4
12
18
23
37
Category temperature range(℃)
Capacitance tolerance
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋125
−
Dissipation Factor (DF)
＋125℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 2 times of the initial limit
ESR
Within 2 times of the initial limit
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
SVP
SEPC
SEQP
SEP
Resistance to soldering heat※2
Guidelines and
precautions
003
15
32
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±5% of the initial value
DF
Within the initial limit
ESR
Within the initial limit
LC
Within the initial limit (after voltage processing)
Series
Size
code
（＋）
(SEQP)
Rated capacitance
Rated voltage
15min.
L
4min.
19min.
Size list
Technical data
μF
57
Within 1.5 times of the initial limit
(unit : mm)
φd
Polarity marking
（Cathode）
Case No.
Selection guide
Catalog Deletion and
EOL models
DF
ESR
Marking and dimensions
SEQP
Surface mount type
Within ±20% of the initial value
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125℃.
※2 Please refer to page 25 for flow soldering conditions.
Catalog Deletion and
EOL series
POSCAP
Line-up
Flow method
(260±5℃ X 10s)
Within the initial limit
△C/C
F
SEPF
LC
φD
Radial lead type
SXE
0.75 to 1.25
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
125℃, 1,000h,
105℃, 5,000h,
Rated voltage applied
Endurance
Damp heat(Steady state)
SVQP
Specifications
Rated voltage
Equivalent series resistance (ESR)
SVPG
RoHS directive/Halogen-free compliant
High voltage（32V）
Endurance： 125℃ 1,000h, 105℃ 5,000h
Specifications
Leakage current※1
SXV
Series
RV
6.8
15
18
22
39
47
56
68
82
100
120
150
180
270
330
470
560
680
820
1,200
φD
6.3
10
16
C6
C6
C6
C6
E7
E7
F8
E12
E12
F8
F13
F13
E7
E7
F8
E12
F13
F8
E12
F13
20
C6
E7
F8
E12
F13
L max
F
φd ±0.05
2.5±0.5
0.45
C6
6.3
6.0
E7
8.0
7.0
F8
10.0
8.0
E12
8.0
12.0
F13
10.0
13.0
RV : Rated voltage
4.0
±0.5
32
E7
F8
E12
3.5±0.5
5.0±0.5
3.5±0.5
5.0±0.5
0.45
0.50
0.60
0.60
OS-CON
Line-up
C6
E7
E12
F13
Rated ripple current Allowable ripple current
100kHz（mArms）
105℃＜Tx≦125℃※1 Tx≦105℃※1
DF
(% max)
Leakage current
(μA)(max)
After 2 minutes
20SEQP22M
20
22
60
458
1450
10
220
16SEQP39M
16
39
50
512
1620
10
312
10SEQP56M
10
56
45
537
1700
12
280
6SEQP82M
6.3
82
45
537
1700
12
258
4SEQP150M
4.0
150
40
572
1810
12
300
32SEQP6R8M
32
20SEQP47M
20
16SEQP82M
10SEQP120M
6.8
100
440
1400
10
44
47
45
598
1890
12
470
16
82
40
670
2120
12
656
10
120
35
810
2560
12
600
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
SXV
SVPG
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
6SEQP150M
6.3
150
35
810
2560
12
472
SVQP
4SEQP330M
4.0
330
35
810
2560
12
660
SVP
15
80
560
1800
10
96
32SEQP15M
F8
Rated
Rated
ESR(mΩ) (max)
voltage capacitance
100kHz to 300kHz/20℃
(V)
(μF)
Technical data
Part number
Image of
case size
32
20SEQP68M
20
68
40
759
2400
12
272
16SEQP150M
16
150
30
955
3020
12
480
10SEQP270M
10
270
25
1170
3700
12
540
6SEQP330M
6.3
330
25
1170
3700
12
416
4SEQP680M
4.0
680
25
1170
3700
12
544
SXE
Radial lead type
Size
code
Series system
diagram
Surface mount type
SEQP series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
32SEQP18M
32
18
50
790
2500
12
115
POSCAP
Line-up
20SEQP100M
20
100
24
1050
3320
15
400
Guidelines and
precautions
16SEQP180M
16
180
20
1151
3640
15
576
10SEQP330M
10
330
17
1250
3950
15
660
6SEQP470M
6.3
470
15
1332
4210
15
592
4SEQP560M
4.0
560
13
1430
4520
15
448
20SEQP150M
20
150
20
1367
4320
15
600
16SEQP330M
16
330
16
1493
4720
15
792
10SEQP560M
10
560
13
1655
5230
15
840
6SEQP820M
6.3
820
12
1721
5440
15
775
4SEQP1200M
4.0
1200
12
1721
5440
18
960
Selection guide
Technical data
※1 Tx : Ambient temperature
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Surface mount type
Catalog Deletion and
EOL models
58
OS-CON
Line-up
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Radial lead
type
SEP
Items
Condition
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
SVQP
Specifications
Rated voltage
(V)
−
2.5
4.0
6.3
10
16
20
Surge voltage
(V)
Room temperature
3.3
5.2
8.2
12
18
23
Category temperature range (℃)
Capacitance tolerance
120Hz/20℃
M : ±20
120Hz/20℃
Please see the attached characteristics list
Rated voltage applied, after 2 minutes
Please see the attached characteristics list
100kHz to 300kHz/20℃
Please see the attached characteristics list
(％)
Characteristics of impedance
ratio at high temp.
and low temp.
−55 to ＋105
−
Dissipation Factor (DF)
Equivalent series resistance (ESR)
SVPG
＋105℃ Z/Z20℃
0.75 to 1.25
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
ESR
Within 1.5 times of the initial limit
105℃, 3,000h,
Rated voltage applied
(2.5V → 2,000h)
Endurance
60℃, 90 to 95%RH,
1,000h,
No-applied voltage
Damp heat(Steady state)
SEQP
SEP
Guidelines and
precautions
Polarity marking
（Cathode）
Case No.
003
820
6
Selection guide
μF
59
Within 1.5 times of the initial limit
Within 1.5 times of the initial limit
LC
Within the initial limit (after voltage processing)
△C/C
Within ±5% of the initial value
DF
Within the initial limit
ESR
Within the initial limit
LC
Within the initial limit (after voltage processing)
(unit : mm)
φd
Series
Size
code
（＋）
(SEP)
Rated capacitance
Rated voltage
15min.
L
4min.
19min.
Size list
Technical data
Catalog Deletion and
EOL models
DF
ESR
Marking and dimensions
SEP
Surface mount type
Within ±20% of the initial value
※1 In case of some problems for measured values, measure after applying rated voltage.
※2 Please refer to page 25 for flow soldering conditions.
Catalog Deletion and
EOL series
POSCAP
Line-up
Flow method
(260±5℃ X 10s)
Within the initial limit
△C/C
F
SEPC
Resistance to soldering heat※2
LC
φD
Radial lead type
SEPF
0.75 to 1.25
−55℃ Z/Z20℃
Based the value at
100kHz, ＋20℃
SVP
SXE
RoHS directive/Halogen-free compliant
Standard of Radial Lead Type
Endurance： 105℃ 3,000h
Specifications
Leakage current※1
SXV
Series
RV
22
33
39
47
56
68
82
100
120
150
180
220
270
330
470
560
680
820
1,200
1,500
φD
4.0
6.3
10
16
C6
C6
C6
C6
E7
E7
E12
F13
E7
F8
E12
F8
F13
E7
C6
F8
E12
F13
E7
F8
E12
F13
F8
E12
F13
L max
F
φd ±0.05
2.5±0.5
0.45
C6
6.3
6.0
E7
8.0
7.0
F8
10.0
8.0
E12
8.0
12.0
F13
10.0
13.0
RV : Rated voltage
2.5
±0.5
20
C6
E7
E7
F8
F8
F8、E12
F13
3.5±0.5
5.0±0.5
3.5±0.5
5.0±0.5
0.45
0.50
0.60
0.60
OS-CON
Line-up
E7
F8
E12
Rated
capacitance
(μF)
ESR(mΩ) (max)
100kHz to 300kHz/20℃
Rated
ripple current
100kHz (mArms) at 105℃
DF
(% max)
20SEP22M
20
22
60
1450
10
220
16SEP39M
16
39
50
1620
10
312
10SEP56M
10
56
45
1700
12
280
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
6SEP82M
6.3
82
45
1700
12
258
4SEP100M
4.0
100
40
1810
12
200
SXV
4SEP150M
4.0
SVPG
150
40
1810
12
300
20SEP33M
20
33
45
1890
12
330
20SEP47M
20
47
45
1890
12
470
16SEP82M
16
82
40
2120
12
656
10SEP120M
10
SVPF
SVPE
SVPS
120
35
2560
12
600
6SEP150M
6.3
150
35
2560
12
472
4SEP220M
4.0
220
35
2560
12
440
4SEP330M
4.0
330
35
2560
12
660
56
40
2400
12
224
SVQP
SVP
20SEP56M
20
20SEP68M
20
68
40
2400
12
272
20SEP100MX
20
100
35
2570
12
400
16SEP150M
16
150
30
3020
12
480
10SEP270M
10
270
25
3700
12
540
6SEP330M
6.3
330
25
3700
12
416
4SEP470M
4.0
470
25
3700
12
376
4SEP680M
4.0
680
25
3700
12
544
20SEP100M
20
100
24
3320
15
400
16SEP180M
16
180
20
3640
15
576
10SEP330M
10
330
17
3950
15
660
6SEP470M
6.3
470
15
4210
15
592
4SEP560M
4.0
560
13
4520
15
448
2.5
680
13
4520
15
340
20SEP150M
20
150
20
4320
15
600
16SEP330M
16
330
16
4720
15
792
560
13
5230
15
840
2R5SEP680M
F13
Leakage current
(μA)(max)
After 2 minutes
Image of
case size
Surface mount type
C6
Rated
voltage
(V)
Part number
Series system
diagram
10
10SEP560M
6SEP820M
6.3
820
12
5440
15
775
4SEP1200M
4.0
1200
12
5440
18
960
2R5SEP1500M
2.5
1500
12
5440
18
750
SVPD
SVPC
SVPB
SVPA
SXE
Radial lead type
Size
code
Technical data
SEP series characteristics list
Selection guide
Guidelines and
precautions
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Technical data
※1 Tx : Ambient temperature
Frequency coefficient for ripple current
Frequency
120Hz≦ f ＜1kHz
1kHz≦ f ＜10kHz
10kHz≦ f ＜100kHz
100kHz≦ f ≦500kHz
Coefficient
0.05
0.3
0.7
1
Surface mount type
Catalog Deletion and
EOL models
60
OS-CON
Line-up
Catalog Deletion and EOL series
Image of
case size
Products list
Packing
specifications
（SMD type）
Packing
specifications
（Radial lead type）
Recommended
soldering
condition
Fundamental
structure
Characteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
SXV
The following table is a list of our parts which have been deleted from our catalogs. If you are
using any of the following models, please substitute with the suggested alternative model/series.
Also, we have announced the end of life of aluminum solid capacitors with organic semiconductive
electrolyte. We hope alternative parts (Aluminum Solid Capacitors with Organic Semiconductive
Electrolyte) will continue to serve your needs. Thank you very much.
■The list of alternatives for higher voltage
Series
SVPG
Surface mount type
SVPF
SVPE
SVPS
SVPD
SVPC
SVPB
SVPA
Size Code
A5
B6
SVP
C6
SVQP
E7
SVP
Radial lead type
SXE
SEPF
SEPC
SEQP
SEP
Catalog Deletion and
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
F8
SVQP
E7
Models for
Deletion
6SVP15M
4SVP22M
10SVP22M
6SVP33M
6SVP56M
4SVP82M
4SVP100M
10SVP82M
6SVP120M
6SVP150M
4SVP150M
4SVP220M
4SVP470M
6SVQP150M
4SVQP220M
Year of
Deletion
2002
2002
2002
2002
2002
2002
2002
2002
2002
2002
2002
2002
2002
2007
2007
Alternative
model
10SVP15M
6SVP22M
16SVP22M
10SVP33M
10SVP56M
6SVP82M
4SVP150MX
16SVP82M
10SVP120M
10SVP150MX
10SVP150MX
6SVP220MX
6SVP470MX
10SVQP150M
6SVQP220M
■The list of alternatives to 25V products
Series
SVP
SEP
Size Code
C6
E7
F8
E12
F12
C6
E7
F8
E12
F13
Models for
Deletion
25SVP6R8M
25SVP10M
25SVP22M
25SVP33M
25SVP56M
25SEP6R8M
25SEP10M
25SEP22M
25SEP33M
25SEP56M
Year of
Alternative series
Deletion
2013
2013
SVPD series
2013
SVPF series
2013
2013
2013
2013
SEPF series
2013
2013
2013
※Surge voltage of above models is 25V and they need to apply the temperature derating voltage, so
customers are encouraged to migrate to models in alternative series which is superior in operating voltage.
Technical data
■End of life/ Aluminum Solid Capacitors with Organic Semiconductive Electrolyte
Series
Size Code
Status
All size
EOL
SZP
SF
SP
SC
SA
Surface mount type
SL
SH
SS
SG
SPA
SM
SN
Catalog Deletion and
EOL models
61
SV
工商网监
湘ICP备2023018690号
