Conductive Polymer Aluminum
Solid Capacitors
Surface Mount Type
SVPS series
Features
● 105 ℃ 5000 h
● RoHS compliance, Halogen free
Specifications
Size code
A5
B6
C6
E7
F8
Rated voltage range
4.0 V to 10 V
4.0 V to 16 V
–55 ℃ to +105 ℃
4.0 V to 20 V
4.0 V to 25 V
4.0 V to 16 V
Nominal cap.range
10 μF to 33 μF
22 μF to 68 μF
22 μF to 150 μF
10 μF to 270 μF
100 μF to 680 μF
Category temp. range
Capacitance tolerance
DC leakage current
±20 % (120 Hz / +20 ℃)
Please see the attached characteristics list
Dissipation factor (tan δ)
Please see the attached characteristics list
Dissipation factor (tanδ)
DC leakage current
+60 ℃, 90 % to 95 % RH, 1000 h, No-applied voltage
Capacitance change
Within ±20 % of the initial value
Dissipation factor (tanδ)
DC leakage current
Marking
≦ 150 % of the initial limit
Within the initial limit (after voltage processing)
Dimensions (not to scale)
Polarity marking (−)
0.2 max.
H
øD
Series code*
⊕
L
R. voltage
(V)
* Depends on the case size.
R. capacitance
(μF)
W
⊖
Lot No.
Size
code
A5
B6
C6
E7
F8
C
Damp heat
(Steady state)
≦ 150 % of the initial limit
Within the initial limit
P
Endurance
+105 ℃ 5000 h, rated voltage applied (25 V product : 20 V applied)
Capacitance change
Within ±20 % of the initial value
R
Unit:mm
øD±0.5
+0.1
L -0.4
W±0.2
H±0.2
C±0.2
R
P*1
4.0
5.0
6.3
8.0
10.0
5.4
5.9
5.9
6.9
7.9
4.3
5.3
6.6
8.3
10.3
4.3
5.3
6.6
8.3
10.3
5.0
6.0
7.3
9.0
11.0
0.6 to 0.8
1.0
1.4
2.1
3.2
4.6
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
*1 : Reference
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03-Feb-17
SVPS series
Characteristics list
Case size
Rated
Rated
capacitance
voltage
(±20 %)
(V)
(μF)
4.0
6.3
Specifications
(mm)
øD
L
Size
code
Ripple
current*1
(mA rms)
ESR*2
(mΩ max.)
Standard (Reel size : ø380)
*3
tan δ
LC*4
(μA)
Min.
Packaging
Q'ty
(pcs)
Part number
33
4.0
5.4
A5
740
200
0.15
66
4SVPS33M
2000
68
5.0
5.9
B6
1970
30
0.12
300
4SVPS68M
1500
150
6.3
5.9
C6
2570
22
0.12
300
4SVPS150M
1000
270
8.0
6.9
E7
3220
22
0.12
500
4SVPS270M
1000
680
10.0
7.9
F8
4130
20
0.12
544
4SVPS680M
500
22
4.0
5.4
A5
740
200
0.12
69.3
6SVPS22M
2000
47
5.0
5.9
B6
1970
30
0.12
300
6SVPS47M
1500
120
6.3
5.9
C6
2570
22
0.12
300
6SVPS120M
1000
220
8.0
6.9
E7
3220
22
0.12
500
6SVPS220M
1000
470
10.0
7.9
F8
4130
20
0.12
592
6SVPS470M
500
10
4.0
5.4
700
220
0.10
50
10SVPS10M
2000
15
4.0
5.4
740
200
0.10
75
10SVPS15M
2000
10
A5
33
5.0
5.9
B6
1100
70
0.12
165
10SVPS33M
1500
68
6.3
5.9
C6
2200
30
0.12
300
10SVPS68M
1000
E7
2760
30
0.12
500
10SVPS150MX
1000
3020
30
0.12
300
10SVPS150M
8.0
6.9
10.0
7.9
330
10.0
7.9
3770
24
0.12
660
10SVPS330M
500
22
5.0
5.9
B6
1060
90
0.10
176
16SVPS22M
1500
39
6.3
5.9
C6
2460
24
0.12
300
16SVPS39M
1000
82
8.0
6.9
E7
2760
30
0.12
262
16SVPS82M
1000
100
10.0
7.9
2670
35
0.12
320
16SVPS100M
500
180
10.0
7.9
3430
29
0.12
576
16SVPS180M
500
22
6.3
5.9
1450
60
0.10
88
20SVPS22M
1000
47
8.0
6.9
1890
45
0.12
188
20SVPS47M
1000
10
8.0
6.9
1500
60
0.10
125
25SVPS10M
1000
150
16
20
25
F8
F8
C6
E7
500
*1: Ripple current (100 kHz / +105 ℃)
: The surface temperature of aluminum case top must not exceed 105 ℃.
A rise in temperature due to self-heating by ripple current should be factored in.
*2: ESR (100 kHz to 300 kHz / +20 ℃)
*3: tan δ (120 Hz / +20 ℃)
*4: After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency(f)
120 Hz ≦ f < 1 kHz
1 kHz ≦ f < 10 kHz
10 kHz ≦ f < 100 kHz
100 kHz ≦ f < 500 kHz
Coefficient
0.05
0.3
0.7
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03-Feb-17
Guidelines and precautions regarding the
technical information and use of our products
described in this online catalog.
■ If you want to use our products described in this online catalog for applications requiring special
qualities or reliability, or for applications where the failure or malfunction of the products may directly
jeopardize human life or potentially cause personal injury (e.g. aircraft and aerospace equipment,
traffic and transportation equipment, combustion equipment, medical equipment, accident prevention,
anti-crime equipment, and/or safety equipment), it is necessary to verify whether the specifications of
our products fit to such applications. Please ensure that you will ask and check with our inquiry desk
as to whether the specifications of our products fit to such applications use before you use our products.
■ The quality and performance of our products as described in this online catalog only apply to our
products when used in isolation. Therefore, please ensure you evaluate and verify our products under
the specific circumstances in which our products are assembled in your own products and in which our
products will actually be used.
■ If you use our products in equipment that requires a high degree of reliability, regardless of the
application, it is recommended that you set up protection circuits and redundancy circuits in order
to ensure safety of your equipment.
■ The products and product specifications described in this online catalog are subject to change for
improvement without prior notice. Therefore, please be sure to request and confirm the latest product
specifications which explain the specifications of our products in detail, before you finalize the design
of your applications, purchase, or use our products.
■ The technical information in this online catalog provides examples of our products' typical operations
and application circuits. We do not guarantee the non-infringement of third party's intellectual property
rights and we do not grant any license, right, or interest in our intellectual property.
■ If any of our products, product specifications and/or technical information in this online catalog is to
be exported or provided to non-residents, the laws and regulations of the exporting country,
especially with regard to security and export control, shall be observed.
■ The switchover date for compliance with the RoHS Directive/REACH Regulations varies depending
on the part number or series of our products.
■ When you use the inventory of our products for which it is unclear whether those products are
compliant with the RoHS Directive/REACH Regulation, please select "Sales Inquiry" in the website
inquiry form and contact us.
We do not take any responsibility for the use of our products outside the scope of the
specifications, descriptions, guidelines and precautions described in this online catalog.
16-Apr-21
Notices / Items to be observed
Notices
■ Applicable laws and regulations
・This product complies with the RoHS Directive (Restriction of the use of certain hazardous substances in electrical and
electronic equipment (DIRECTIVE 2011/65/EU and(EU)2015/863)).
・ No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing
this product. We do not use PBBs or PBDEs as brominated flame retardants.
・ Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method,
on the occasion of export of this product.
・ These products are not dangerous goods on the transportation as identified by UN(United Nations) numbers or UN
classification.
■ Limited applications
・ This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home appliances,
computers and other office equipment, optical equipment, measuring equipment.
・ An advanced specification must be signed individually for high-reliability use that might threaten human life or
property due to a malfunction of the capacitor.
■ Intellectual property rights and licenses
・ The technical information in this specification provides examples of our products' typical operations and application
circuits. We do not guarantee the non-infringement of third party's intellectual property rights and we do not grant
any license, right, or interest in our intellectual property.
Items to be observed
■ For specification
・ This specification guarantees the quality and performance of the product as individual components.
The durability differs depending on the environment and the conditions of usage.
Before use, check and evaluate their compatibility with actual conditions when installed in the products.
When safety requirements cannot be satisfied in your technical examination, inform us immediately.
・ Do not use the products beyond the specifications described in this document.
■ Upon application to products where safety is regarded as important
Install the following systems for a fail-safe design to ensure safety if these products are to be used in equipment where
a defect in these products may cause the loss of human life or other signification damage, such as damage to vehicles
(automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances,
combustion/ gas equipment, rotating rotating equipment, and disaster/crime prevention equipment.
(1) The system is equipped with a protection circuit and protection device.
(2) The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event
of a single fault.
■ Conditions of use
・ Before using the products, carefully check the effects on their quality and performance, and determined whether or not they
can be used. These products are designed and manufactured for general-purpose and standard use in general electronic
equipment. These products are not intended for use in the following special conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high
concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx.
(4) In an environment where strong static electricity or electromagnetic waves exist.
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these products.
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin and
other material.
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular, when using water or
a water-soluble cleaning agent, be careful not to leave water residues)
(8) Using in the atmosphere where strays acid or alkaline.
(9) Using in the atmosphere where there are excessive vibration and shock.
(10) Using in the atmosphere where there are low pressure or decompression.
・ Please arrange circuit design for preventing impulse or transitional voltage.
Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage, instantaneous high
voltage, high pulse voltage etc.
・ Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid deterioration of
characteristics and functions of each product. Electrolyte leakage damages printed circuit and affects performance,
characteristics, and functions of customer system.
16-Apr-21
Conductive Polymer Aluminum Solid Capacitors
Application Guidelines(OS-CON)
1. Circuit design
1.1 Prohibited circuits
(1) Leakage current of the OS-CON may increase in the following conditions.
(a) Soldering
(b) When voltage is not applied : high temperature no-load test, high temperature and high humiditynoload test,
rapidly changing temperature test, etc.
(2) Avoid the use of the OS-CON in the following type of circuits because leakage current may increase.
(a) High-impedance circuits
(b) Coupling circuits
(c) Time constant circuits
(d) Other circuits that are significantly affected by leakage current.
✽ If you plan to use 2 or more OS-CONs in a series connection, please contact us before use。
1.2 Failure and life-span
The failure rate is 0.5 % /1000 h (Confidence level : 60 %) based on JIS C 5003.
The prospective failure is not zero. The mainly failure modes are as follows.
1.2-1 Contingency failure
The most common failure mode is a short circuit. Mainly caused by the soldering or operating temperature
environment, along with heat stresses, electrical stresses or mechanical stressesas follows.
・ Applying voltage over the rated voltage.
・ Applying reverse voltage
・ Excessive mechanical stress
・ Applying rush current by sudden charge or discharge out of the specification.
(1) The following phenomenon is seen when short-current is applied to the OS-CON.
(a) When current is relatively low. (ø10 : approx 1 A or less, ø8 : approx 0.5 A or less, ø6.3 : approx 0.2 A or less)
The OS-CON becomes heated, but no effects are visible even when the current is continously carried.
(b) When the short circuit currents exceed the mentioned value above.
After internal temperature increase, sealing rubber may be turned over.
In some cases, odorous gas may be produced.
(2) In case a short circuit occurs, ensure safety by fully considering the followings.
(a) If odorous gas is released, turn off the main power of the equipment.
In this case, keep your face and hands away from the area.
(b) Though it depends on the conditions, it takes seconds to minutes before odorant gas generates.
Protective circuit should operate in this period.
(c) If the gas comes into eyes, rinse immediately. If the gas is inhaled, gargle immediately.
(d) Do not lick the electrolyte. If the electrolyte touches skin, wash it off with soap immediately.
(e) The OS-CON contains combustible substances. In case a large current continues to flow after a short circuit,
in the worst case, the shorted-out section may ignite. For safety, install a redundant circuit or a protective
circuit, etc.
1.2-2 Wear-out failure (life time)
When lifetime span exceeded the specified guarantee time of endurance and damp heat, electrolyte might insulate
and cause electric characteristic changed. This is called an open circuit.
The electric characteristics of capacitance and ESR may possibly change within the specified range in specifications
even if it is used under the condition of the rated voltage, electric and mechanical performance.
Please note it when designing.
1.3 Leakage current
Mechanical stress may cause OS-CON’s leakage current increased.
In such a case, leakage current will gradually decrease by applying voltage (withinthe category voltage and the upper
limit of category temperature).
1.4 Rapid charge and discharge limitation
Allowance of a large rush current to flow due to rapid charge and discharge may result in short circuit or large leakage
current. The protection circuit, to maintain high reliability, is recommended when rush current to flow to the OS-CON
is in the following cases.
(1) Products which 10 times of allowable ripple current is less than 10 A : It is when 10 A or over of rush current is
applied.
(2) Products which 10 times of allowable ripple current is 10 A or over : It is when rush current, which the figure is over
10 times of allowable ripple current, is applied.
05-Mar-21
Conductive Polymer Aluminum Solid Capacitors
2. Mounting
2.1 Soldering with a soldering iron
(1) When lead terminals for radial lead type must be processed because the lead pitch and the PCB holes do not match,
process them without any stresses to the OS-CON before soldering.
(2) Solder without any excessive stresses to the OS-CON itself.
(3) When the OS-CON has been soldered once and needs to be removed, remove it after the solder has been completely
melted.
(4) Do not let the tip of the soldering iron touch the OS-CON itself.
2.2 Flow soldering
(1) Do not apply flow soldering to OS-CON SMD type.
(2) Do not solder the OS-CON itself by submerging it in melted solder.
(3) Solder the opposite side that the OS-CON is mounted on.
(4) Note that flux does not adhere to anywhere expect the lead terminal.
(5) Note that other components do not fall over and touch the OS-CON when soldering.
2.3 Reflow soldering
(1) Do not apply reflow soldering to OS-CON Radial Lead type.
(2) Please contact us for setting VPS conditions.
2.4 Capacitor handling after soldering
Do not subject the OS-CON to excessive stress as follows.
(1) Do not tilt, bend or twist the OS-CON.
(2) Do not move the PCB with holding the OS-CON itself.
(3) Do not hit the OS-CON with objects.
(4) When stacking PCBs, make sure that the OS-CON does not touch other PCBs or components.
2.5 Circuit board cleaning
Check the following items before washing PC board with these detergents: high quality alcohol-based cleaning fluid
such as Pine-a ST-100S, clean thru 750H, 750L, 710M, 750K or Techno Care FRW 14 through 17 or detergents
including substitute freon as AK-225AES or IPA.
(1) Use immersion or ultrasonic waves to clean within 2 minutes.
(2) The temperature of the cleaning fluid should be less than 60 °C.
(3) Watch the contamination of the detergent such as conductivity, pH, specific gravity, water content, etc.
(4) Do not store the OS-CON in a location subject to gases from the cleaning fluid or in an airtight container after
cleaning.
(5) Dry the PCB or OS-CON with hot air that should be less than the upper category temperature.
(6) Please note that indication may disappear when rubbing print side after washing depending on a cleaner.
(7) Please contact us for details about detergents, cleaning methods and detergents other than those listed
above.
2.6 Fixatives and coating materials
(1) Select the appropriate covering and sealant materials for the OS-CON. In particular, don’t use acetone in the fixative,
coating agent and diluent.
(2) Before applying the fixative or coating, completely remove any flux residue and foreign matter from the area where
the board and the OS-CON will be jointed together.
(3) Allow any detergent to dry before applying the fixative or coating.
(4) Please contact us for the fixative and coating heat curing conditions.
2.7 Capacitor insulation
Be sure to completely separate the case, negative lead terminal, positive lead terminal and PC board patterns with each
other due to the following reasons.
(1) Insulation is not guaranteed at a part of resin on the surface of a case.
(2) It offers inconstant resistance between a case and a negative lead terminal and it isn’t insulated.
05-Mar-21
Conductive Polymer Aluminum Solid Capacitors
3. Storage
Open the bags just before mounting and use up all products once opened,
For keeping a good solderability, store the OS-CON as follows.
Before unsealing
SMD type*1
Radial
lead type
Within 24 months after shipment
Bag packing product
Within 30 months after shipment
Taping product
Within 24 months after shipment
After unsealing
Within 30 days from opening
(packaged with carrier tape)
Within 7 days from opening
*1 : The JEDEC J-STD-020 standard is not applicable
✽ Intellectual property right
We, Panasonic Group are providing the product and service that customers can use without anxiety, and are working
positively on the protection of our products underintellectual property rights.
Representative patents relating to OS-CON are as follows:
US Patent No.7158367
05-Mar-21