ADPW11

PS-A (ADPW) Pressure sensor Built-in amplifier and compensating circuit New PS-A PRESSURE SENSOR Direct water pressure detection type FEATURES TYPICAL APPLICATIONS 1. Not only air, now water pressure can be detected directly. • Water heaters (water level detection) • Industrial water pressure monitoring *For other media, please inquire. 2. Linear output achieved for both positive and negative pressure. 3. Standalone type One-touch connection using connector 4. Low power consumption contributes to energy savings. RoHS compliant ORDERING INFORMATION ADPW 1 1 PS-A Direct water pressure detection type Pressure sensors Shape 1: Standalone type Installation hole: 4.5mm dia., 40mm pitch Pipe shape: 6mm dia., No 0-ring groove Compatible plug: XMP-04V Rated pressure 1: Negative pressure –19.6kPa Positive pressure 49.0kPa * Please inquire about pressure ranges. RATING 1. Use conditions and Absolute maximum ratings Item Type of pressure Pressure medium Max. applied pressure Max. applied voltage Ambient temperature range Storage temperature range ADPW11 Gauge pressure Air and water –90 to 350kPa 7.0 V –10 to 80°C 14 to 176°F –20 to 85°C –4 to 185°F Remarks Note*1 Note: *1. Please consult us for other pressure media. * When the pressure medium is a liquid, the maximum pressure it can withstand may be exceeded due to shock pressure (water hammer), etc., caused by sudden changes in pressure. Please only use after sufficiently verifying in the actual environment under actual conditions. ASCTB243E 201209-T 201201-T Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e PS-A (ADPW) 2. Electrical characteristics Item ADPW11 –19.6 to 49kPa –2 to 5m 5.0±0.25V 16mW (typ.) 2.0±0.06V 4.5±0.12V 1.0±0.084V 2.5±0.06V 1.0±0.024V ±0.5%FS ±0.3%FS 30mV ±2.0%FS 15Ω (typ.) Rated pressure Drive voltage Power consumption Offset voltage Rated output voltage for positive pressure Rated output voltage for negative pressure Rated span voltage for positive pressure Rated span voltage for negative pressure Non linearity Pressure hysteresis Offset voltage temperature characteristics Sensitivity temperature characteristics Output impedance Notes: *2. *3. *4. *5. Remarks Converts to water level Note*2 and *3 Note*2 and *3 Note*2 and *3 Note*2 and *3 Note*2 and *3 Note*2 and *3 Note*2, *3 and *5 Note*2, *3 and *5 Note*3 and *4 Note*3, *4 and *5 Note*2 Indicates output when temperature is 25°C 77°F. Indicates output when drive voltage is 5 V. Although output fluctuates due to fluctuations in the drive voltage, this is not included. Indicates from output value at 25°C 77°F and the change of output at 0 and 50°C 32 to 122°F. Full scale (FS) indicates 0 to 49 kPa. REFERENCE DATA 1.-(2) Offset voltage temperature characteristics Output voltage, V 4 3 Pressure sensors 2 1 –20 –10 0 10 20 30 Pressure, kPa 40 50 1.-(3) Sensitivity temperature characteristics 30 Sensitivity temperature characteristics, %FS 5 Offset voltage temperature characteristics, mV 1.-(1) Output characteristics 20 10 0 –10 –20 –30 0 32 10 50 20 30 40 68 86 104 Temperature, °C °F 50 122 2.0 1.5 1.0 0.5 0.0 –0.5 –1.0 –1.5 –2.0 0 32 10 50 20 30 40 68 86 104 Temperature, °C °F 50 122 2. THB (high temperature high humidity bias test) Offset voltage change, mV 30 20 10 0 –10 –20 –30 0 20 40 60 Time, hours 80 Panasonic Corporation 100 Span voltage change for positive pressure, mV Within 85°C 185°F and 85% RH 5 V applied between No. 2 (VDD) and No. 3 (GND) Applied pressure: 0kPa 30 20 10 0 –10 –20 –30 100ASCTB243E 0 20 201209-TASCTB243E 40 60 80201209-T Time, hours Automation Controls Business Unit industrial.panasonic.com/ac/e ASCTB243E 201209-T PS-A (ADPW) DIMENSIONS (mm inch) The CAD data of the products with a CAD Data mark can be downloaded from: http://industrial.panasonic.com/ac/e CAD Data 50.0 1.969 40.0 1.575 18.0 .709 a. di ia. 5 d 4. 77 2 -.1 2 37.4 1.472 (12.1) (.476) GND VDD Vout 2.0 .079 4.0 .157 C C. 0.5 02 0 8.0 .315 Pressure inlet hole 2.0 dia. .079 dia. 6.0 dia. .236 dia. 8.8 dia. .346 dia. Connector Manufacturing company: J.S.T. Mfg. Co. Ltd. Plug housing: XMP-04V Retainer: XMS-04V Socket contact: SXA-001T-P0.6 Top Top Bottom Bottom 2) Air tightness may be compromised due to the case breaking or loosening if the screws are not tightened properly. Please make sure the proper torque is used when tightening the screws during sensor installation. ASCTB243E 201209-T 201201-T 2. Environment 1) Please avoid using or storing the pressure sensor chip in a place exposed to corrosive gases (such as the gases given off by organic solvents, sulfurous acid gas, hydrogen sulfides, etc.) which will adversely affect the performance of the pressure sensor chip. 2) Avoid use in environments susceptible to condensation and freezing. 3) The connector on this product is not water proof. Please make sure there is no problem with the installation environment before installing. 4) When using with cable wiring, we recommend using shielded cables and keeping them as short as possible in order to prevent noise from leaking in. 5) Since the internal circuitry may be destroyed if an external surge voltages is supplied, provide an element which will absorb the surges. 6) Please note that noise entering the power supply may cause malfunction and breakdown. 7) Static electricity can damage this product. Please take sufficient cautions when handling. Panasonic Corporation Automation Controls Business Unit 3. Other handling precautions 1) Oil has been placed inside the pressure intake opening in order to protect the pressure sensor chip and sensor chip. Do not insert foreign objects, such as a needle, into the pressure intake opening. Doing so may cause damage to the sensor chip or cause oil to leak. 2) As a rule, please do not use this product if it has been dropped. If you still intend to use it, please verify functionality first. 3) Use an operating pressure which is within the rated pressure range. Using a pressure beyond this range may cause damage. 4) Avoid using the pressure sensor where it will be susceptible to ultrasonic or other high-frequency vibration. 5) To assure reliability, check the sensor under actual loading conditions. Avoid any situation that may adversely affect its performance. industrial.panasonic.com/ac/e Pressure sensors NOTES 1. Installation direction 1) Influenced by the weight of the filled oil, the offset voltage will shift depending on the installation direction. This product should be installed in the recommended orientation shown below in order to achieve detection results it was designed for.