Programmable Controller
FP0R SERIES
Conforming to EMC Directive
Recognition
(Some models only)
Listing
(Some models only)
The New Standard of Ultra-compact PLCs
NEW
Equipped with RS485 Port
Largest in its class *1
Large Capacity Program and
Data Memory
Fastest in its class *1
Ultra-high Speed Processing
Multi-axis Control available
without Expansion
Industry’s First *2
Battery-less Automatic Backup
of All Data
*1. Among compact PLCs with up to 128 I/O points based on our research as of July 1, 2011
*2. Based on our research as of July 1, 2011
2011.08
panasonic-electric-works.net/sunx
Our Mission is to Maximize Customer Benefits with
Enhancing Advanced Functionality and Performance.
The Answer is
, Superior to Basic Ultra-
Smallest in its class *1
The control unit is small at 90 mm 3.54 in in height and 25 mm 0.98 in in width.
Even when expanded with three expansion units, the total width only 100 mm
The ultra-compact space-saving body size facilitates the miniaturization of
target machines, equipment, and control panels.
Ultra
100 mm
3.94 in
I/O points compact
Min.
10 points
Max.
128 points
The number of I/O points
is expandable up to 128
by adding three expansion
units having 32 I/O points
each to one control unit
equipped with 32 I/O points.
60 mm
2.36 in
25 mm
0.98 in
Input/Output terminals
Expansion
unit
Expansion
unit
Expansion
unit
Only one cable is required
for communications with
the “Control FPWIN Pro”
or "Control FPWIN GR"
programming tool.
Tool ports
Equipped with both
USB 2.0 and RS232C
ports.
▲
C14R Control unit
▲
C32T Control unit
Multi-axis (4-axis) control is available without expansion units.
The built-in 4-axis pulse outputs allow multi-axis motor control
without positioning units or other expansion units.
Conventional model
Control
unit
FP0R
Expansion
unit
Space
saving
FP0R
Y0
Y2
Y4
Y6
Economical
M
M
M
M
2
M
M
M
M
50 kHz max. each axis
Outstanding Products
Worldwide simultaneous launch of the 3-year warranty
For details, visit the following website:
panasonic-denko.co.jp/ac/e/fasys/warranty
compact Models.
3.94 in.
Industry’s First *
Battery-less automatic backup of
all data
The F type (FP0R-F32) has a built-in FeRAM, which is a cutting-edge
device that allows the automatic saving of all data without a backup
battery.
● There is no need to worry about data loss after a long vacation.
● Battery replacement is no longer necessary when shipping or transferring the unit overseas.
● Replacement of equipment and restoration of idle equipment is easy.
● The unit can be powered off flexibly on weekends or at other
non-operating times, promoting energy saving.
* Based on our research as of July 1, 2011
NEW
Equipped with RS485 port
Up to 99 units can be connected, expanding applications for
the eco-conscious business field.
The PLC link is available with up to 16 other FP series and
FP0R units.
Fastest in its class *1
Ultra-high speed processing
Ultra-high speed: 80 ns/step (ST instructions)
* Within a range of 0 to 3,000 steps. Processing of the 3,001st and later steps is
580 ns, 1.5 times faster than the conventional model.
Note: Unit expansion increases the base time.
Base scan time:
I/O refresh + base time
Without expansion units: 0.2 ms or less
With expansion units: 0.2 ms or less + (1 x Number of expansion units) ms
Large capacity independent
comment memory
Program maintenance and management become easier.
USB tool port provided as
standard equipment
Programming work becomes simpler, easier, and quicker,
improving the production efficiency.
Full-fledged positioning functions
A variety of dedicated instructions enable high-accuracy
positioning.
Largest in its class *1
Large capacity program
Program capacity: 32 k steps *2
Data register: 32 k words *2
*1 Among compact PLCs with up to 128 I/O points based on our research as of July 1, 2011
*2 C10, C14 or C16 control unit: Program capacity of 16 k steps and data register of 12 k words
3
POSITIONING
■ Jog positioning control (F171 instruction)
The motion can be started without a preset target
value. When a stop signal is input, the target value
is set, and the motion is slowed to a stop.
The jog operation (without a preset target value) The positioning operation
is continued until the stop signal is input.
slows to a stop.
■ Individual settings for acceleration and deceleration
(available for F171, F172, and F174 instructions)
The acceleration time and deceleration time can be
individually set.
Acceleration time
Deceleration time
The speed can be changed
during the jog operation.
Start signal
Individually settable within a range of 30 ms to 32,767 ms
Stop signal
Useful for
Useful for
■ Labelers: Stopping the motion at a constant distance from the point where
a label end detection signal is triggered
■ Processing machines: Stopping the motion at a constant distance from
the point where a processing object edge detection
signal is triggered, and cut/drill the object
■ Changing the speed
(available for F171 and F172 instructions)
The target speed can be changed by an external
signal input during the jog operation or trapezoidal
control operation.
■ Labelers: Starting the operation at a relatively low acceleration to prevent
tape from breaking
Stopping the operation at high deceleration when detecting the
label end to save the tape
■ Lifts: Optimizing the acceleration and deceleration during ascending and
descending transfers.
■ Measuring the pulse frequency (F178 instruction)
Pulses input in a specified period by a single
instruction are counted, and the frequency is calculated.
Specified period
The speed can be freely changed until the operation starts to
decelerate to a stop.
Useful for
Setting range: 1 ms to 5,000 ms
Useful for
■ Speed synchronization of transfer or processing equipment.
■ Detection of motor rotation speed for encoder feedback control
■ Built-in 4-axis pulse outputs (Transistor output type)
■ High-speed counters and pulse outputs
Two sets can simultaneously undergo two-axis linear
interpolation.
Ladder programs can be combined to create an
application for counting pulse signals from the encoder
through the high-speed counter input and adjusting the
pulse output frequency based on the count to
synchronize the slave axis speed with the master axis
speed.
No complicated speed calculation or programming is required.
Two-axis linear interpolation is available by using the F175 dedicated
instruction. Two sets such as two X-Y tables, for example, can be
simultaneously controlled.
FP0R
In the right-hand figure, the
speed of conveyor 1, which
is inverter-controlled, is
measured based on the
encoder pulse count, and
pulses are output to the
slave motor (for jog
operation) according to the
measured speed in order to
synchronize the speed of
conveyor 2.
Two-axis X-Y table x 2
■ Built-in multipoint PWM outputs (4 channels)
The pulse output port of FP0R can also serve as a PWM output
port. One of the application examples is an analog voltage
output, which can be used for inverter speed control.
FP0R
5V
INVERTER
Y0,Y2,Y4,Y6
COM
Vin
GND
The speed can be controlled by
changing the ON width of the PWM
output.
4
Rin
The unit can also serve as an
analog voltage output when a
smoothing capacitor is inserted in
the circuit.
Conveyor 1
Inverter
Motor
(master)
Encoder
Conveyor 2
High-speed
counter
Motor
(slave)
Pulse output
NETWORK
■ PLC link (MEWNET-W0)
■ FP Web-Server2
Contact data can be shared among up to 16 PLC units, including
FP0R, FPΣ, FP-X, FP2/FP2SH, and a mixture of them, without the
need for programs.
The FP0R operation status can be monitored
on a Web browser.
RS232C / 2 stations / 115.2 kbps /
15 m 49.2 ft
RS232C
1-to-1 link available
Connectable
with FPΣ,
FP-X,
FP2/FP2SH as
well as FP0R
The FP0R operation status can be monitored on a
Web browser by connecting FP Web-Server2
and FP0R via RS232C and making required
settings using dedicated software (FP Web
Configurator Tool 2).
FP Web-Server 2
(AFP0611)
Application examples
Use two FP0R units to control the assembly and transfer sections of a small
machine respectively, connect them via the PLC link, and share one display
Ethernet 100BASE-TX
RS485
Up to 16 units connectable
RS485 / 16 stations / 115.2 kbps / 1200 m 3937 ft
FP0R
FP Web-Server 2
MCU
RS232C
FPΣ, FP-X, and FP2/FP2SH can
also be mixed in the network.
Application examples
Management of manufacturing line operations
■ RS485 serial communication
■ RS232C general-purpose serial communications
Compatible with both Modbus master and slave RTU.
The control unit has an RS232C port for serial
communications.
This feature expands applications for the eco-conscious business field,
and is ideal for the control of air conditioners, temperature, and
electrical power.
The RS232C port allows for direct connection to an operation
display panel or a PC. Also, it facilitates bi-directional data
communications with bar-code readers and other RS232C
devices.
* The port block has S, R, and G terminals for connection.
Operation display panels can also be connected to the tool port.
* Both the relay output and transistor output types of control unit equipped with an RS232C
port are available.
Temperature
controller
PLC
Eco-POWER METER
● For connection with an operation display panel or a PC
● Up to 99 units can be connected.
When 17 or more FP series units need to be linked, you can link up to 99 units
by using the Modbus function instead of MEWNET-W0. Since each FP0R unit
can be either a master or a slave, a multi-master link can be created by passing
a token from a user program.
Host computer
(commercially available PC)
Token passing
Operation display
panel
● For data communications with general-purpose RS232C devices
A multi-master link of
up to 99 units can be created.
Master /
Slave
Master /
Slave
Master /
Slave
Master /
Slave
FP0R
Master /
Slave
IMAGECHECKER
Bar-code reader ID card management system
■ CC-Link slave unit
■ I/O link unit
This unit is compatible with CC-Link, which is an open
network, and capable of reading/writing four-word data
through a maximum of 16 input and 16 output points.
This link unit enables FP0R to serve as a slave
station of MEWNET-F (remote I/O system) and
exchange I/O data from 32 input points and 32
output points with a master station without the need
for programs.
MW
3456
12
FP0R
3456
12
CC-Link
789
789
Connectable
as slaves
FP0
CC-Link
slave unit
0
Other companies’
PLC as a master
station
FP0-CCLS
(AFP07943)
0
Ethernet
Master station with an
FP2 multi-wire link unit
(FP2-MW) mounted
FP0-IOL
(AFP0732)
RS485 / 32 stations / 500 kbps / 700 m 2296 ft
FP0R
FP0 I/O
link unit
FP0R
FP0 I/O
link unit
5
OTHER USEFUL FUNCTIONS
■ Program protection
■ Analog I/O
● Program upload protection setting
The lineup includes a compact analog I/O unit with one analog
output and two analog input channels, an A/D converter unit with
eight analog input channels, and a D/A converter unit with four
analog output channels. Communication using up to 24 channels
is possible. Both the compact body size and the high
input/output resolution of 1/4,000 (12 bits) have been achieved.
The DIP switches in the unit cover a variety of input/output
ranges and are user-friendly.
User programs can be protected from unauthorized copying by
disabling program upload using our software, FPWIN. This
function is useful for users who manage original programs on a
PC.
Upload
(Read)
Upload
(Read)
PC
Since uppercase and lowercase alphanumeric characters can be
used, there are approx. 218 trillion possible password combinations.
If an incorrect password is entered three times in a row, a
cold reboot is required.
This function is useful for users who upload programs from
FP0R.
■ Temperature controller
Thermocouple unit
4ch AFP0420
(FP0-TC4)
8ch AFP0421
(FP0-TC8)
The clock allows for year, month, day, hour, minute, and second
data processing. The clock data can be linked to periodic
monitoring of production data and operation status, and the
management of error history records.
■ Interrupt input
This function takes in input signals at high speed regardless of
the scan time and instantly executes the interrupt program. This
is useful for high-accuracy positioning control or control of
defective item ejector valves. The X0 to X7 inputs can be
designated as interrupt inputs (C10: X0 to X5).
■ Pulse catch
6
Laser analog
sensor
Potentiometer
Analog I/O unit
Input: 2ch / Output: 1ch
AFP0480
(FP0-A21)
A/D converter unit
Input: 8ch
D/A converter unit
Voltage output: 4ch
AFP0401
(FP0-A80)
AFP04121
(FP0-A04V)
D/A converter unit
Current output: 4ch
AFP04123
(FP0-A04I)
■ EEPROM data saving (F12 and P13 instructions)
■ Built-in real-time clock (T type only)
This function can take in 10 μs short pulse
inputs and is therefore ideal for taking in
signals from a sensor to detect small
components.
Inverter
FP Memory Loader
● Eight-character password
● A temperature control program can be
written in only one line by using a PID
instruction (F356 EZPID), facilitating
temperature control programming by a
PLC, which had previously been
considered difficult.
● The total accuracy is ±0.8°C ±33.44°F (K, J
and T range). Two types are available:
4-channel and 8-channel types. Up to three
units can be connected, allowing
high-accuracy multi-point PID control of a
maximum of 24 channels.
Pressure sensor
10 μs
The X0 to X7 inputs can
be designated as pulse
catch inputs.
All FP0R series models are equipped with EEPROM, which can
electrically rewrite data and retain data without the need for
voltage supply. Setting data and production result data can be
written and saved by the P13 instruction, and read out by the F12
instruction when necessary.
2,048 words / block
(Writable in 16 blocks max.)
P13 (Write)
F12 (Read)
EEPROM
Note: Each block is limited to 10,000 write operations.
■ Program download in RUN mode (Comment writable)
Even while the equipment is operating with FP0R in RUN mode, a
whole program edited offline can be downloaded to FP0R, and
comments can be written simultaneously.
Programs can be changed without stopping a running production
line.
Control FPWIN Pro
or
Control FPWIN GR
Download in RUN mode
Programs and comments can
be simultaneously written.
PROGRAMMING SOFTWARE
■ Control FPWIN Pro (IEC61131-3 compliant Windows version software)
Compliant with international standard IEC61131-3
Programming software approved by PLC Open
LD
SFC
Ladder
Diagram
1. Five programming languages can be used.
IL
2. Easy to reuse well-proven programs
FBD
Function
Block
Diagram
Features
Sequential
Function
Chart
Instruction
List
ST
Programming can be done using the language most familiar to the
developer or using the language most suited to the process to be
performed. High-level (structured text) languages that allow structuring,
such as C, are supported.
Efficiency when writing programs has been greatly increased by being
able to split programming up for each function and process using
structured programming.
3. Keep know-how from getting out
Structured
Text
By "black boxing" a part of a program, you can prevent know-how from
leaking out and improve the program's maintainability.
4. Uploading of source programs from PLC possible.
Maintainability increased by being able to load programs and comments
from the PLC.
● Programming in the language most suited to the
process
Easy-to-understand, efficient programs can be created, for example, by
using a ladder program for machine control or ST for communications
control.
● Programming in the language you are good at
Programming time can be greatly reduced by the easy ability to split and
then integrate programming for each function and process.
Main program
(SFC)
Designer A
(SFC)
Positioning
program (ST)
Designer B
(ST)
Communications
program (ST)
Completed
program
Completed
program
Designer C
(ST)
Malfunction handling
program (ladder)
5. Programming for all models in the FP series possible.
Operational Environment
* FP0R is compatible with Ver. 6.1 or later.
OS
Windows 2000/XP/Vista/7 (Note)
Hard disk capacity
At least 120 MB
CPU
Pentium III processor (700 MHz) or compatible
Onboard memory
At least 256 MB RAM or more
Screen resolution
At least 1,024 x 768
Display colors
High Color (16-bit) or higher
Applicable PLC
FP0R/FP0/FPΣ/FP-X/FP-e/FP2/FP2SH
Note: Only Ver. 6.2 or later is compatible with Windows 7. (To be released in September 2011)
Designer D
(ladder)
■ Control FPWIN GR (Windows version software)
The ladder programming software for FP series
Program status display
Highly operational software tool for maximizing convenience in the field
Features
Tool bar
1. Easy field operations not requiring the use of a mouse
for data entry, search, writing, monitoring and timer
changes, all carried out only from the keyboard.
Access often-used
functions using icons.
2. All FP series PLCs are supported.
Data
monitoring
window
3. Easy programming with wizard functions.
4. Communication with GTWIN and PCWAY
simultaneously through the same port.
5. A simulation function is available.
Relay
monitoring
window
Program display
Search window
Allows you to search
various data
Function bar
Buttons for instruction input
and confirmation,
on-line/off-line selection and
PLC mode selection.
Operational Environment
* FP0R is compatible with Ver. 2.8 or later.
OS
Windows 98/Me/2000/XP/Vista/7 (Note)
Hard disk capacity
At least 40 MB
CPU
Pentium 100 MHz or higher
Onboard memory
At least 64 MB (depends on OS)
Screen resolution
At least 1,024 x 768
Display colors
High Color (16-bit) or higher
Applicable PLC
FP0R/FP0/FPΣ/FP-X/FP-e/FP2/FP2SH
Note: Only Ver. 2.90 or later is compatible with Windows 7.
7
PART NUMBER LIST
■ Control units
10 points Input: 6, Relay output: 4
10 points Input: 6, Relay output: 4
Terminal block type
14 points Input: 8, Relay output: 6
Connector type
14 points Input: 8, Relay output: 6
Connector type
Terminal block type
AFP0RC10RS
AFP0RC10RM
AFP0RC14RS
AFP0RC14RM
with RS232C
AFP0RC10CRS
with RS232C
AFP0RC10CRM
with RS232C
AFP0RC14CRS
with RS232C
AFP0RC14CRM
with RS485
AFP0RC10MRS
with RS485
AFP0RC14MRS
16 points Input: 8, Transistor output: 8
32 points Input: 16, Transistor output: 16
32 points Input: 16, Transistor output: 16
MIL connector type
MIL connector type
MIL connector type
32 points Input: 16, Transistor output: 16
MIL connector type
T type
F type
AFP0RC16T
AFP0RC16P
AFP0RC32T
AFP0RC32P
with RS232C
AFP0RC16CT
AFP0RC16CP
with RS232C
AFP0RC32CT
AFP0RC32CP
with RS232C
AFP0RT32CT
AFP0RT32CP
with RS232C
AFP0RF32CT
AFP0RF32CP
with RS485
AFP0RC16MT
AFP0RC16MP
with RS485
AFP0RC32MT
AFP0RC32MP
with RS485
AFP0RT32MT
AFP0RT32MP
with RS485
AFP0RF32MT
AFP0RF32MP
■ Expansion units
8 points Input: 8
8 points Input: 4, Relay output: 4 8 points Relay output: 8
8 points Transistor output: 8
32 points Input: 16, Transistor output: 16
MIL connector type
Terminal block
type
MIL connector type
MIL connector type
AFP0RE8X
AFP0RE8RS
Connector type
AFP0RE8RM
Terminal block type
AFP0RE8YRS
AFP0RE8YT
AFP0RE8YP
16 points Input: 16
16 points Transistor output: 16 16 points Input: 8, Transistor output: 8 16 points Input: 8, Relay output: 8
MIL connector type
MIL connector type
AFP0RE16X
AFP0RE16YT
■ Intelligent units
Analog I/O unit Input: 2 ch, Output: 1 ch
MIL connector type
AFP0RE16YP
AFP0RE16T
AFP0RE16P
Terminal block
type
Connector type
AFP0RE16RS
AFP0RE16RM
AFP0RE32P
Units in common with FP0
A/D converter unit Input: 8 ch
D/A converter unit Voltage output: 4 ch
D/A converter unit Current output: 4 ch
Terminal block type
Terminal block type
Terminal block type
Terminal block type
Part number: AFP0480
Product number: (FP0-A21)
AFP0401
(FP0-A80)
AFP04121
(FP0-A04V)
AFP04123
(FP0-A04I)
■ Link and Communication units
I/O link unit
AFP0RE32T
CC-Link slave unit
Units in common with FP0
KS1 Signal converter
FP Web-server 2 Unit
Thermocouple unit
4 ch
8 ch
AFP0420
(FP0-TC4)
AFP0421
(FP0-TC8)
■ Power supply unit and others
Power supply unit
Units in common with FP0
FP memory loader
Input: 100 to 240 V AC,
Output: 24 V DC, 0.7 A
Part number: AFP0732
Product number: (FP0-IOL)
8
AFP07943
(FP0-CCLS)
AKS1202
AFP0611
(FP-WEB2)
Part number: AFP0634
Product number: (FP0-PSA4)
Data clear type: AFP8670
Data hold type: AFP8671
* FP0R is compatible with Ver. 2.0 or later.
INSTALLATION AND OPTIONS
■ Installation
The control unit width is only 25 mm 0.98 in*.
Even when expanded to allow for 128 I/O points,
the total width is only 105 mm 4.13 in.
The control unit is pocket-sized: W 25 x H 90 x D 60 mm W 0.98 x
H 3.54 x D 2.36 in.
The number of I/O points can be expanded up to 128. Even with
the maximum expansion, the size is only W 105 x H 90 x D 60 mm
W 4.13 x H 3.54 x D 2.36 in. The ultra-compact body size and
installation area facilitate the miniaturization of target machines,
equipment, and control panels.
Up to three expansion units can be directly
connected without connection cables.
The expansion units can be directly connected to the control unit
with a simple operation using the expansion connector and lock
lever on the side of the unit. Dedicated cables or backplanes are
not necessary for expansion.
* The 32 I/O points type control unit is 30 mm 1.18 in in width.
● Three options for installation methods
The control unit can be directly mounted on a panel by using the optional flat
type mounting plate.
Control
unit
DIN rail
Slim type mounting plate
Expansion
unit
Expansion
unit
Expansion
unit
units
(Upcantobe3expanded.
)
Flat type mounting plate*
* Cannot be used when expanded.
A terminal block type and a connector type are available. Both can be detached for easy wiring.
■ Options
● Wiring tools
Terminal screwdriver
Molex connector pressure contact tool
Necessary when wiring relay output type and
terminals block (Phoenix).
Necessary when wiring relay output type
and molex connectors.
Necessary when wiring transistor output type
connectors.
Part number: AXY52000FP
Part number: AFP0805
Part number: AFP0806
Multi-wire connector pressure contact tool
● Parts for mounting
FP0 Slim type mounting plate
Flat type mounting plate
Screw-stop attachment plate, Slim model
Screw-stop attachment plate, Flat model
Part number: AFP0803 (including 10 pieces)
Part number: AFP0804 (including 10 pieces)
● I/O cables
● Flat cable connector set (10 leads)
Relay output molex type I/O cable
Transistor output type I/O cable
Loose-wiring cable (9 leads) with molex socket attached at
one end, AWG20, 0.5 mm2, 1 set: 2 cables (blue & white)
< Length: 1 m 3.28 ft > 2 cable set
Part number: AFP0551
< Length: 3 m 9.84 ft > 2 cable set
Part number: AFP0553
Loose-wiring cable (10 leads) with connectors attached at
one end, AWG22, 0.3 mm2, 1 set: 2 cables (blue & white).
< Length: 1 m 3.28 ft > 2 cable set
Part number: AFP0521
Part number: AFP0808
(including 4 pieces)
< Length: 3 m 9.84 ft > 2 cable set
Part number: AFP0523
Notes: 1) One I/O cable set (2 cables) is necessary with the following models: C10RS / C10RM, C14RS / C14RM, E8RS / E8RM, E16RS / E16RM
2) One I/O cable set (2 cables) is necessary with the following models: C16T / E16X, E16T / E16YT
3) Two I/O cable sets (total 4 cables) are necessary with the following models: C32T / E32T
● Maintenance parts
Terminal socket
Attaches to relay output
and terminal block types.
Part number: AFP0802 (2 sokets per pack)
Molex socket
Attaches to relay output and
molex connector types.
Part number: AFP0801 (2 sokets per pack)
Wire-press socket
Attaches to transistor output
type.
Part number: AFP0807 (2 sokets per pack)
FP0R Power cable (Length: 1 m 3.28 ft)
Attaches to FP0R control unit.
Part number: AFPG805 (1 cable per pack)
9
OPTIONS
■ OPTIONS
● RT-3 unit relays (Power PhotoMOS relay type)
RT-3 unit relay
Contact
arrangement
1 Form A × 4
Type
DC only
(equipped with AQZ102)
AC / DC dual use
(equipped with AQZ204)
Rated input
voltage
12 V DC
24 V DC
12 V DC
24 V DC
Product No.
RT3SP1-12V
RT3SP1-24V
RT3SP2-12V
RT3SP2-24V
RT-3 Unit relay
Part No.
Packing quantity
AY34001
AY34002
Inner carton: 1 piece
Outer case: 20 pieces
AY35001
AY35002
Notes: 1) Only for use with Power PhotoMOS relays. Cannot be equipped with PA relays.
2) Please consult us other contact arrangement.
● RT-3 unit relays (PA relay type)
RT-3 unit relay
Contact
arrangement
Rated input voltage
12 V DC
24 V DC
1 Form A × 4
Product No.
RT3S-12V
RT3S-24V
RT-3 Unit relay
Part No.
Packing quantity
AY33001
Inner carton: 1 piece
Outer case: 20 pieces
AY33002
Notes: 1) Only for use with PA relay type. Cannot be equipped with Power PhotoMOS relay
stndard type. However, equipping with voltage sensitive type is possible.
2) 5 V DC type relays are also available. Please consult us.
3) Please consult us other contact arrangement.
● 4-point terminals
4-point terminals
Type
PA relay and Voltage sensitive type power PhotoMOS relay type
Rated input voltage
12, 24 V DC
Part No.
AY30000
Packing quantity: inner carton: 1 piece, outer case: 20 pieces
Mountable relays
PA relay
Power PhotoMOS relay
(voltage sensitive type)
Mountable relays for 4-point terminal
Product name
PA relay
Power PhotoMOS relay (voltage sensitive type)
Part No.
APA3311 and APA3312
AQZ10*D (DC only)
AQZ20*D (AC / DC dual use)
Note: Never mount relays into this product other than those given above.
Doing so will cause malfunction, breakdown, and breakdown of the connected product.
● RT-2 relay terminals
Pressure connector
connect type
Wire-direct connect
type
DIN rail mounting type
1. Pressure connector connect type
I / O type
Input device
Output device
Rated voltage
12 V DC
24 V DC
12 V DC
24 V DC
Product No.
RT2S-ID16-12V
RT2S-ID16-24V
RT2S-OD16-12V
RT2S-OD16-24V
Part No.
AY231501
AY231502
AY232501
AY232502
Product No.
RT2S-C-ID16-12V
RT2S-C-ID16-24V
RT2S-C-OD16-12V
RT2S-C-OD16-24V
Part No.
AY231511
AY231512
AY232511
AY232512
Packing quantity
Inner carton: 1 piece
Outer case: 10 pieces
2. Wire-direct connect type
I / O type
Input device
Output device
10
Rated voltage
12 V DC
24 V DC
12 V DC
24 V DC
Packing quantity
Inner carton: 1 piece
Outer case: 10 pieces
■ OPTIONS
● Cables
Connecting cables for FP series and Interface terminal
Product name and shape
RT-2 relay terminal
RT-1 PC relay terminal
16 points
Input unit
Input side:
10-pin × 2
RT-2 relay terminal
RT-1 PC relay terminal
For FP0 and FP0R 8-point input
20-pin
Input side:
10-pin
−
−
AY15013 AY15014 AY15015 AY15016 AY15017
−
−
AY15913 AY15914 AY15915 AY15916 AY15917
−
−
AY15023 AY15024 AY15025 AY15026 AY15027
−
−
AY15923 AY15924 AY15925 AY15926 AY15927
For FP0, FP0R and FPΣ
16-point input
20-pin
8 points
Input unit
250 mm
9.84 in
Connecting cable
Length (Part number)
500 mm 1,000 mm 1,500 mm 2,000 mm 3,000 mm 5,000 mm
19.69 in 39.37 in 59.06 in 78.74 in 118.11 in 196.85 in
10-pin
Expansion cable
Interface
terminal
10-pin
No. of
connector
contacts of
controller side
Product Controller
name
side unit
10-pin
Expansion cable with
wire-pressed terminal
Connector terminal
20-pin
16 points
I/O unit
For FP0, FP0R and FPΣ
16-point output
20-pin
RT-2 relay terminal
RT-1 PC relay terminal
10-pin
16 points
Output side:
Output unit 10-pin × 2
For FP0 and FP0R 8-point output
10-pin
FP0
FP0R
FPΣ
RT-2 relay terminal
RT-1 PC relay terminal
20-pin
−
10-pin
I/O side: 20-pin
10-pin
10-pin
M type 16-point,
34-pin output cable
8 points
Output side:
Output unit 10-pin
AYT52202 AYT52203 AYT52204 AYT52205 AYT52206 AYT52207
20P
32 points
Controller side
16 points
16 points
20-pin
RT-2 relay terminal
RT-1 PC relay
terminal / S type
20-pin
I/O side: 40-pin
Terminal side
64 points
I/O unit
40-pin
For FPΣ 64-point I/O unit
−
−
AY15633 AY15634 AY15635 AY15636 AY15637
(Standard packing; carton: 1 pc., Case: 10 pcs.)
Expansion cables with wire-pressed terminal for relay terminal
Product name and shape
Expansion cable with wire-pressed terminal
20-pin
20-pin
Relay terminal side
I/O type
Relay terminal
Length (Part number)
1,000 mm 1,500 mm 2,000 mm 3,000 mm 5,000 mm
39.37 in 59.06 in 78.74 in 118.11 in 196.85 in
16-point both input
and output
RT-2 relay terminal
RT-1 PC relay terminal / S type
AY15853 AY15854 AY15855 AY15856 AY15857
Note: Please consult us regarding connecting cables for the various controllers. Regarding the expansion cables with wire-pressed terminal, the triangle mark does not correspond to wire No. 1, so be sure
to inquire for details.
● WAGO DIO Station
For Easy and Secure Connection Between
FP0R and a Sensor
Power supply unit
FP0R
Even a thin sensor or
electrical wire can be
connected.
(0.08 - 0.5 sq)
Example: Sensor
(2) Cable for input
24 V DC
(3) Cable for output
(4) DIO station
(1) Common terminal block
24 V DC
can be
branched.
Power is supplied
through the cable to the
PLC common terminal
and the sensor.
The cable comes in
lengths up to 10 m
32.81 ft in increments
of 0.1 m 0.33 ft.
Example: Switch and Lamp
Quick connection with
DIO using the finger lever
The connector can be
reused.
(2)(3) Cable specifications
AWG28, Rated voltage: 30 V
Outer diameter of sheath: ø 4.4 ø 0.17
Minimum allowable bending radius: R = 13.2
Power supply wire: 0.3 sq, 250 mm 9.84 in
Product name
(1) Common terminal block
(2) PM flexible cable for input
(3) PM flexible cable for output
(4) 8 ponts, MIL-DIO station
Product number
PM-PW8-739/3.5
PM-FP0X-M733SS-F1M
PM-FP0Y-M733SS-F1M
PM-M733-3X8PC-S1
Ident number
51197832
51251907
51251909
51238076
Contact WAGO Kontakttechnik GmbH & Co. KG for inquiries
about DIO Station.
URL: http://www.wago.com
11
COMPATIBILITY
■ Compatibility between FP0 and FP0R
Programs
FP0R has an "FP0-compatible mode". This mode provides conditions
for functions, memory areas, system registers, etc. identical to those
of FP0. If programs in FP0 are transported to FP0R, FP0R can
function identically as FP0 did (with some exceptions described
below).
This high degree of compatibility ensures
easy and worry-free replacement of FP0
with FP0R even if the device or machine to
be manufactured is identical.
Installation
The shape, outside dimensions, installation method, and the
connector pin arrangement are identical to those of FP0.
● It is recommended that Control FPWIN Pro or FPWIN GR should be used for transporting FP0 programs to FP0R.
Before an FP0 program is downloaded to FP0R, a message stating "Switch to FP0-compatible mode for the download?"
appears. If "Yes" is chosen, FP0R will automatically be set in FP0-compatible mode.
Download an FP0
program into FP0R.
Switch to
FP0-compatible
mode?
Yes
Switched to
FP0-compatiblemode.
The program is
downloaded.
FP Memory Loader
PC
When the FP Memory Loader (AFP8670/AFP8671) is used to read a program from FP0 and transport it
to FP0R, FP0R will automatically be set into FP0-compatible mode. For the program transport to FP0R,
use FP Memory Loader Ver. 2.0 or later. (Ver. 1.1 and earlier versions are not compatible with FP0R.)
● FP0 specification items not covered by FP0-compatible mode (See "FP0R User's Manual" for details.)
Item
FP0
5 ms / block (256 blocks max.: 1,280 ms)
Instruction F170: PWM output frequency range
0.15 Hz to 1 kHz
6 Hz to 1 kHz
High-speed counter/pulse output elapsed value
± 24 bits
± 32 bits
Instruction P13: EEPROM write time
Instruction F168: Home return
Instruction F169: Pulse output
Instruction F144: Serial data communications
* Writing even only one block takes 100 ms.
The elapsed value is not counted during home return.
The elapsed value is counted during home return.
"Non-counting mode" selectable
Counted and added even when "non-counting mode" is
selected
Transmittable data size: Unlimited
Transmittable data size: 2,048
Note: The F type has no compatible functions because it does not correspond to any units of the conventional FP0 series.
12
FP0R (FP0-compatible mode)
100 ms in units of 32 blocks (256 blocks max.: 800 ms)
■ Control unit replacement table
FP0
FP0R
Product name
Product No.
Part No.
FP0-C10RS
AFP02123
FP0-C10RM
AFP02113
FP0-C10CRS
AFP02123C
FP0-C10CRM
AFP02113C
FP0-C14RS
AFP02223
FP0-C14RM
AFP02213
FP0-C14CRS
AFP02223C
FP0-C14CRM
AFP02213C
FP0-C16T
AFP02343
FP0-C16P
AFP02353
FP0-C16CT
AFP02343C
FP0-C16CP
AFP02353C
FP0-C32T
AFP02543
FP0-C32P
AFP02553
FP0-C32CT
AFP02543C
FP0-C32CP
AFP02553C
FP0-T32 Control unit with RS232C port,
clock / calendar function and 10 k type
FP0-T32CT
AFP02643C
FP0-T32CP
AFP02653C
FP0-S-LINK Control unit with RS232C port
FP0-SL1
AFP02700
FP0-C10 Control unit
FP0-C10 Control unit with RS232C port
FP0-C14 Control unit
FP0-C14 Control unit with RS232C port
FP0-C16 Control unit
FP0-C16 Control unit with RS232C port
FP0-C32 Control unit
FP0-C32 Control unit with RS232C port
Product name
FP0R-C10 Control unit
FP0R-C10 Control unit with RS232C port
FP0R-C14 Control unit
Order
receiving
will be
discontinued
in August
2012.
FP0R-C14 Control unit with RS232C port
FP0R-C16 Control unit
FP0R-C16 Control unit with RS232C port
FP0R-C32 Control unit
FP0R-C32 Control unit with RS232C port
FP0R-T32 Control unit with RS232C port
and real clock / calendar function
Part No.
AFP0RC10RS
AFP0RC10RM
AFP0RC10CRS
AFP0RC10CRM
AFP0RC14RS
AFP0RC14RM
AFP0RC14CRS
AFP0RC14CRM
AFP0RC16T
AFP0RC16P
AFP0RC16CT
AFP0RC16CP
AFP0RC32T
AFP0RC32P
AFP0RC32CT
AFP0RC32CP
AFP0RT32CT
AFP0RT32CP
Continue to be available
No corresponding models
FP0R-F32 Control unit with RS232C port
AFP0RF32CT
AFP0RF32CP
■ Expansion unit replacement table
FP0
FP0R
Product name
FP0-E8
FP0-E16
FP0-E32
Product No.
Part No.
Product name
Part No.
FP0-E8X
AFP03003
AFP0RE8X
FP0-E8RS
AFP03023
AFP0RE8RS
FP0-E8RM
AFP03013
FP0-E8YRS
AFP03020
FP0-E8YT
AFP03040
FP0-E8YP
AFP03050
FP0-E16X
AFP03303
FP0-E16RS
AFP03323
FP0-E16RM
AFP03313
FP0-E16T
AFP03343
FP0-E16P
AFP03353
AFP0RE16P
FP0-E16YT
AFP03340
AFP0RE16YT
FP0-E16YP
AFP03350
AFP0RE16YP
FP0-E32T
AFP03543
FP0-E32P
AFP03553
FP0R-E8
Order
receiving
will be
discontinued
in August
2012.
AFP0RE8RM
AFP0RE8YRS
AFP0RE8YT
AFP0RE8YP
AFP0RE16X
AFP0RE16RS
AFP0RE16RM
FP0R-E16
FP0R-E32
AFP0RE16T
AFP0RE32T
AFP0RE32P
13
SPECIFICATIONS
■ Performance specifications (FP0R Control units)
C10
(Relay output type only)
Product type of FP0R control unit
Programming method / Control method
10 points
[Input: 6, Relay output: 4]
No expansion
(Control unit only)
Number of With expansion 1
I/O points * Same type of control and expansion units
With expansion 2
* Mix type of relay and transistor units
Program memory
Program capacity
C14
(Relay output type only)
C16
C32
(Transistor output type only) (Transistor output type only)
Relay symbol / Cyclic operation
16 points
32 points
14 points
[Input: 8, Relay output: 6] [Input: 8, Transistor output: 8] [Input: 16, Transistor output: 16]
T32
(Transistor output type only)
F32
(Transistor output type only)
32 points
[Input: 16, Transistor output: 16]
Max. 58 points
Max. 62 points
Max. 112 points
Max. 128 points
Max. 128 points
Max. 106 points
Max. 110 points
Max. 112 points
Max. 128 points
Max. 128 points
EEPROM (no backup battery required)
Basic
High-level
Up to 3,000 steps
Operation speed
3,001st and later steps
Internal relay (R)
Relay
Timer / Counter (T / C)
Operation
memory Memory Data register (DT)
area
Index register (IX, IY)
Master control relay points (MCR)
Number of labels (JMP and LOOP)
Differential points
Number of step ladder
Number of subroutines
High speed counter
Pulse output
PWM output
Pulse catch input / interrupt input
Interrupt program
Special
Periodical interrupt
functions
Constant scan
Number of
instructions
32 k steps
110 approx.
210 approx.
Basic instructions: 0.08 µs Min. Timer instructions: 2.2 µs Min. High-level instructions: 0.32 µs (MV instruction) Min.
Basic instructions: 0.58 µs Min. Timer instructions: 3.66 µs Min. High-level instructions: 1.62 µs (MV instruction) Min.
4,096 points
1,024 points
12,315 words
32,765 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each)*
Not available
4 points (50 kHz max. each) Two channels can be controlled individually.*
Not available
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input: 8 programs (6 programs for C10 only) / Periodic: 1 program / Pulse match: 4 programs
In units of 0.5 ms: 0.5 ms to 1.5 sec. / In units of 10 ms: 10 ms to 30 sec.
In units of 0.5 ms: 0.5 ms to 600 ms
16 k steps
One RS232C port is mounted on each of C10CRS, C10CRM, C14CRS, C14CRM, C16CT, C16CP, C32CT, C32CP, T32CT, T32CP, F32CT and F32CP type
(3P terminal block) Transmission speed (Baud rate): 2,400 to 115,200 bits/s, Transmission distance: 15 m 9.8 ft. Communication method: half duplex
RS232C port
RS485 port
Program and system register
One RS485 port is mounted on each of C10MRS, C14MRS, C16MT, C16MP, C32MT, C32MP, T32MT, T32MP, F32MT and F32MP type(3P terminal block)
Transmission speed (Baud rate): 115.2 kbps (It is possible to change to 19.2 kbps by the setting.), Transmission distance: 1,200 m 3,937 ft, Communication method: half duplex
Stored program and system register in EEPROM
Backup of the entire
Backup of the
area by FeRAM
entire area by a
(without the need
built-in secondary
for a battery)
battery
Watchdog timer (690 ms approx.), Program syntax check
Not available
Not available
Available
Rewriting in RUN mode, Download in RUN mode (incl. comments), 8-character password setting, and Program upload protection
Stored fixed area in EEPROM
Counter: 16 points
Internal relay: 128 points
Data register: 315 words
Memory
backup Operation memory
Maintenance
Self-diagnostic function
Real-time clock function
Other functions
* For the limitations while operating units, see the manual.
■ General specifications (FP0R Control units)
Item
Rated voltage
Operating voltage range
C10, C14, C16
Allowed momentary
power off time
C32, T32, F32
Ambient temperature
Storage temperature
Ambient humidity
Storage humidity
Breakdown voltage
(Detection current: 5 mA)
Specifications
24 V DC
20.4 to 28.8 V DC
5 ms (at 20.4 V DC), 10 ms (21.6 V DC or higher)
10 ms (20.4 V DC or higher)
0 to +55 °C 32 to +131 °F
-40 to +70 °C -40 to +158 °F (-20 °C to +70 °C -4 to +158 °F for T32 only)
10 to 95% RH (at 25 °C 77 °F, no condensation)
10 to 95% RH (at 25 °C 77 °F, no condensation)
Input terminals - output terminals, Output terminals – power and functional ground terminals --- Transistor output: 500 V AC for 1 minute (Relay output: 1,500 V
AC for 1 minute) / Input terminals – power and functional ground terminals, Functional ground terminal – power terminal --- Transistor output: 500 V AC for 1
minute (Relay output: 500 V AC for 1 minute) / Output terminals – output terminals (different common terminals) --- Relay output: 1,500 V AC for 1 minute
Insulation resistance
(Test voltage: 500 V DC)
Input terminals - output terminals, input terminals – power and functional ground terminals, output terminals – power and functional ground
terminals, functional ground terminal – power terminal --- Transistor output: 100 MΩ minimum (relay output: 100 MΩ minimum) / Output
terminals – output terminals (different common terminals) --- Relay output: 100 MΩ minimum
Vibration resistance
Shock resistance
Noise immunity
Operating condition
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 µs (using a noise simulator) (Power supply terminal)
Free from corrosive gasses and excessive dust
■ Input specifications (Common to control units and expansion units)
Item
Rated input voltage
Operating voltage range
Rated input current
Input impedance
Input points per common
Min. ON voltage/ON current
Max. OFF voltage/OFF current
Response
OFF → ON
time
ON → OFF
Insulation method
Control unit
(As for the limitation on the number of simultaneous ON points, please refer to the manual.)
Specifications
Expansion unit
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
4.7 mA approx. (at 24 V DC)
9.1 kΩ approx.
5.1 kΩ approx.
6 points / common (C10), 8 points / common (C14, C16), 16 points / common (C32, T32, F32)
19.2 V / 2 mA
2.4 V / 1.2 mA
20 µs or less * An input time constant (0.1 to 64 ms) can be set.
2 ms or less
Same as above
Same as above
Photocoupler
* Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
14
■ Output specifications (Common to control units and expansion units)
for the limitation on the number of simultaneous
( As
)
ON points, please refer to the manual.
1. Relay output type
Item
Output type
Rated control capacity
OFF → ON
Response time
ON → OFF
Mechanical
Life time
Electrical
■ I/O circuit diagrams
Relay output type
Specifications
1a
2 A 250 V AC, 2 A 30 V DC (4.5 A / common)
10 ms approx.
8 ms approx.
2 x 107 operations or more
105 operations or more
None
2 points / common + 1 point / common + 1point / comon (C10),
4 points / common + 1 point / common + 1point / comon (C14)
Surge absorber
Output points per common
2. Transistor output type
NPN
Input
Max. load current
OFF state leakage current
ON state voltage drop
OFF → ON
Response
time
ON → OFF
Current
Internal
circuit
9.1 kΩ
Output points per common
Insulation method
*
9.1 kΩ
*
Xn
Internal
circuit
Internal
circuit
8 points / common (C16T), 16 points / common (C32, T32, F32)
Photocoupler
Xn
COM
9.1 kΩ
COM
*
*
Zener diode
Surge absorber
Internal
circuit
9.1 kΩ
21.6 to 26.4 V DC
C16, E16T and E8YT: 30 mA or less C16, E16P and E8YP: 35 mA or less
C32, T32, F32, E32T and E16Y: C32, T32, F32, E32P and E16YP:
60 mA or less
70 mA or less
Voltage
X0
X0
PNP
Open collector
5 to 24 V DC
24 V DC
4.75 to 26.4 V DC
21.6 to 26.4 V DC
C16, C32, T32 and F32: 0.2 A / point (Max. 14 per common terminal)
E16, E32, E8Y and E16Y: 0.3 A / point (Max. 14 per common terminal)
1 µA or less
0.2 V DC or less
20 µs or less (Load current: 5 mA or more), 0.1 ms or less (Load current: 0.5 mA or more) (Note)
40 µs or less (Load current: 5 mA or more), 0.2 ms or less (Load current: 0.5 mA or more) (Note)
Output type
Rated load voltage
Load voltage allowable range
Transistor output type (NPN)
Input
Specifications
Item
External power
supply
SPECIFICATIONS
Output
Output
Y0
L
Internal
circuit
Yn
Internal
circuit
COM
Internal
circuit
Y0
Internal
circuit
Yn
L
(+)
L
Source
Internal
L
(−)
Internal
Note: For transistor output types, make sure that the externally supplied voltage between the (+) and (-) terminal
is between 21.6 and 26.4 V DC.
* For expansion unit: 5.1 k Ω
Note: For expansion unit: 1 ms or less
■ Analog unit specifications (FP0 Expansion units)
1. Analog input specifications
Specifications
Item
FP0-A21
Number of input points
2 channels / unit
Voltage range
Input range
FP0-A80
8 channels / unit Number of input points
can be changed 2, 4, 6 and 8 channels.
0 to 5 V (K0 to K4000) (Note 1)/-10 to +10 V
-100 to +100 mV (K -2000 to K +2000) (Note 1)
0 to 5 V (K0 to K4000) (Note 1)/
-10 to +10 V (K -2000 to K +2000) (Note 1)
Current range
0 to 20 mA (K 0 to K 4000) (Note 1)
Resolution
1/4,000 (12 bits)
1 ms / channel (Note 2)
±1 % FS or less (0 to 55 °C 32 to 131 °F), ±0.6 % F.S or less (25 °C 77 °F)
1 MΩ or more
Conversion speed
Overall precision
Voltage range
Current range
Voltage range
Absolute
maximum input Current range
Input
impedance
250 Ω
Insulation method
None
Averaging function
Between analog output terminal and
FP0 internal circuit: optical coupler
insulation (non-insulated between
channels)
Between analog input terminal and
A/D converter unit external power
supply: based on insulation-type
DC/DC converter
32 input contact points
Can be switched on and off.
Notes: 1) If the analog input value exceeds the upper or lower limit, the digital value will preserve the upper or lower limit.
2) The time shown below is required before the analog data is reflected in the control unit input.
FP0-A21
Analog intput
WX2
0V
Conversion
time
K0
1 ms
FP0-A80
Analog intput
WX2
0V
K0
10 V
Refresh standby
Refresh
0 ms to scan time
1 ms x number
of expansions
10 V
Refresh
Conversion time
Refresh
standby
1 ms to
0 ms to scan time
1 ms x number of
(Note 4)
1 ms x number
Number of input channels
input channels
of expansions
(Note 3)
2
Output range
-10 to +10 V range (K -2000 to K +2000) (Note 1)
Voltage range
Current range 0 to 20 mA (K0 to K4000) (Note 1)
Conversion speed
500 µs / channel (Note 2)
Overall precision
±1 % F.S. or less (0 to 55 °C 32 to 131 °F), ±0.6 % F.S. or less (25 °C 77 °F)
Output impedance Voltage range
0.5 Ω or less
±10 mA
30 Ω or less
Current range
Insulation method (Note 2)
Number of I/O contact points
16 output contact points
K0
WX2
0V
Analog output
FP0-A04V / FP0-04I
K2000
K0
WX2
Specifications
Input range
Range for K and J
-100.0 to 500.0 °C/-148.0 to 790.0 °F
Range for T
-100.0 to 400.0 °C/-148.0 to 752.0 °F
Range for R
0V
Analog output
0 to 1500.0 °C/32.0 to 1590.0 °F (Note 1)
Digital output
T (when using °C): K -1000 to K4000
T (when using °F): K -1480 to K7520
(When range over using °C: K -1001, K4001 or K8000)
(When range over using °F: K -1481, K7521 or K8000)
(When the thermocouple broken: K8000) (Note 2)
(Until the temperature can be measured at the initial startup: K8001) (Note 3)
R (when using °C): K0 to K15000
R (when using °F): K320 to K15900 (Note 1)
(When range over using °C: K 0, K15001 or K16000)
(When range over using °F: K 0, K15901 or K16000)
(When the thermocouple broken: K16000) (Note 2)
(Until the temperature can be measured at the initial startup: K16001) (Note 3)
16 input contact points, 32 output contact points (Note 3)
Refresh
1 ms x number
of expansions
Waiting for
processing
0 ms to scan time
Conversion
time
500
µs
10 V
K2000
Waiting for
processing
0 ms to
scan time
Conversion
time
Refresh
1 ms x number
of expansions
500 µs / 1 ch
1 ms / 2 ch
10 V
3) The data for two channels will be output to the D/A converter unit with one scan of the control unit.
Item
Resolution
0.1 °C
Sampling cycle (Note 5)
300 ms: when using 2 channels for an input points (Note 4)
500 ms: when using 4 channels for an input points (Note 4)
Overall accuracy
Range for K and J
Range for T
Range for R
(Note 1)
K and J (when using °C): K -1000 to K5000
K and J (when using °F): K -1480 to K7900 (Note 1)
(When range over using °C: K-1001, K5001 or K8000)
(When range over using °F: K-1481, K7901 or K8000)
(When the thermocouple broken: K8000) (Note 2)
(Until the temperature can be measured at the initial startup: K8001) (Note 3)
500 Ω or less
K2000
■ Thermocouple unit specifications (FP0 Expansion units)
Item
1,000 Ω or less
Between analog output terminal
and FP0 internal circuit: optical
coupler insulation (non-insulated
between channels)
Between analog output terminal and FP0 internal circuit:
Between analog output terminal
optical coupler insulation (non-insulated between
and analog I/O unit extenal
channels)
power supply: based on
Between analog output terminal and D/A converter unit
insulation type DC/DC converter
external power supply: based on insulation type DC/DC
Between analog output terminal
converter
and analog input terminal: based
on insulation type DC/DC
converter
Notes: 1) If the digital value exceeds the upper or lower limit, D/A conversion will not take place.
(Analog output will remain as the previous data.)
2) The time shown below is required to update the actual analog output.
K2000
Number of input points 4-channel, 8-channel (The number of input points can be changed 2, 4, 6 and 8 channels.)
4 to 20 mA (K0 to K4000) (Note 1)
1/4,000 (12 bits)
FP0-A21
3) Settings value switch for the number of input channel
4) With each one scan of the control unit, the data for two channels will be loaded into control unit. In other words, if the input
channel number switch is set to 8-channel, the data in the control unit will be updated once every four scans.
Specifications
FP0-A04V
FP0-A04I
Voltage output 4 channels / units Current output 4 channels / units
FP0-A21
1 channel / unit
Resolution
Absolute output
load resistance
±30 mA
Number of I/O contact points
Item
Number of output points
Max. output current Voltage range
±15 V
Between analog input terminal and
FP0 internal circuit: optical coupler
insulation (non-insulated between
channels)
Between analog input terminal and analog
I/O unit external power supply: based on
insulation type DC/DC converter
Between analog input terminal and
analog output terminal: based on
insulation type DC/DC converter
2. Analog output specifications
Specifications
(-100 to 500 °C):
(-100 to 400 °C):
(0 to 99.9 °C):
(100 to 299.9 °C):
(300 to 1,500 °C):
700 ms: when using 6 channels for an input points (Note 4)
900 ms: when using 8 channels for an input points (Note 4)
±0.8 °C or less
±0.8 °C or less
±3 °C or less
±2.5 °C or less
±2 °C or less
Input impedance
1 MΩ or more
• Between thermocouple input terminals and FP0 internal circuits:
Photo-coupler insulation, DC/DC converter insulation
• Between thermocouple input terminal channels: PhotoMOS relay insulation
Number of I/O contact points 32 input contact points (Note 6)
Notes:
1) The measurement range available for degree Celsius is not available for degree Fahrenheit, of which the
upper-limit measurement is set lower than degree Celsius, since the digital value (temperature value displayed) for
degree Fahrenheit is bigger than that for degree Celsius.
2) When the thermocouple is broken, the digital value will become K8000 or K16000 within 70 seconds since broken.
Practice in the ladder program a process for avoiding a risk, would be resulting from a broken thermocouple, and
exchange the thermocouple.
3) Until the conversion data will be ready after the initial startup was made, the digital value shows K8001 or K16001.
Those are not a temperature data. Create a ladder program, so that they are not acquired as a temperature data.
4) The settings of the input channel selection switch.
5) Conversion values for 6-time measurements (6 from the latest 8 measurements, excluding the max. and min.) are
averaged, so that it takes time for the digital value to be displayed due to the rapid temperature change.
6) The control unit reads the data for 2 channels per 1 scan by the control unit. Read data by utilizing the sample
program given in the product specifications and manual.
Insulation method
15
SPECIFICATIONS
■ I/O Link unit specifications
(FP0 Expansion units)
Item
■ FP Web-server2 unit specifications (FP0 Expansion units)
Item
Specifications
Communication method
Synchronous method
Two-wire, half duple
Asynchronous method
Transmission line
2-wire cable
(Twisted-pair cable or VCTF 0.75 mm2 x 2C equivalent)
Transmission distance
(Total distance)
Max. 700 m 2,297 ft (using twisted-pair cable)
Max. 400 m 1,312 ft (using VCTF cable)
Transmission speed (Baud rate)
0.5 Mbits/s
Number of control I/O point
per an I/O link unit
64 points (Input: 32 points and Output: 32 points) (Note)
Remote I/O map allocation
32X / 32Y
Interface
Conforming to RS485
Transmission error check
CRC (Cyclic Redumdancy Check) method
Specifications
Communication
functions
RS232C Ethernet conversion
(PLC remote programming via Ethernet)
E-mail sending function
HTTP server function
General-purpose communication (Server/Client)
PPP server function
Communication
interface
RS232C terminal block 3-pin: Mainly used for PLC connection
RS232C D-Sub 9-pin: Mainly used for Modem connection
100 BASE-TX (RJ45): Used for Ethernet connection
RS232C
communication
Transmission speed: 1,200, 2,400, 4,800, 9,600, 19,200, 38,400,
57,600, 115,200 bits/s
Data length: 7 bits / 8 bits, Parity: Even / Odd / None
Ethernet communication 100 Mbits/s (100 BASE-TX: RJ45)
Note: This point number is the number of points that can be linked for inputting and outputting via the host PLC
and network MEWNET-F. If the output for the I/O link unit error flag is set to ON, this number becomes 63
points (31 input points and 32 output points).
Supported protocol
TCP, UDP, IP, DHCP, FTP, TELNET, HTTP, SMTP, and PPP
Memory size
148 kB approx. (for storing htm files)
Setup method
Setup using FP Web Configurator Tool 2
■ CC-Link slave unit specifications (FP0 Expansion units)
1. Communication specifications
Item
Note: Length of the multi-drop connected cables at both ends
The cable length has restrictions in communication speed, CC-Link version, and dedicated cables
to be used.
For details concerning the CC-Link, refer to the CC-Link Partner Association.
Specifications
Version
CC-Link Ver.1.10
Communication method
Broadcast polling method
Transmission speed
10 Mbits/s, 5 Mbits/s, 2.5 Mbits/s, 625 kbits/s, 156 kbits/s
Max.
transmission distance
(Note)
10 Mbits/s
Ver.1.10 CC-Link cable
CC-Link high-performace cable
CC-Link cable
100 m 328 ft
100 m 328 ft
160 m 525 ft
150 m 492 ft
2.5 Mbits/s
400 m 1,312 ft
200 m 656 ft
625 kbits/s
900 m 2,952 ft
600 m 1,969 ft
156 kbits/s
1,200 m 3,937 ft
1,200 m 3,937 ft
5 Mbits/s
Interface
RS485
Station type
Remote device station
Number of occupied stations
1 station
■ Power supply unit specifications (FP0 Expansion units)
Item
Rated input voltage
When an FP0 thermocouple unit is used with an FP0 CC-Link slave unit, the measurement
accuracy of the thermocouple unit which is installed on the left of the CC-Link slave unit is as
shown in the table below.
Specifications
Thermocouple
0.8 °C 33.44 °F
2 °C 35.6 °F
3 °C 37.4 °F
6 °C 42.8 °F
100 to 299.9 °C 212 to 571.82 °F
2.5 °C 36.5 °F
5 °C 41 °F
300 to 1,500 °C 572 to 2,732 °F
2 °C 35.6 °F
4 °C 39.2 °F
Applicable crimp teriminals
Manufacturer
100 to 240 V AC
Variable input voltage range 85 to 264 V AC
Input
Rated frequency
50/60 Hz
Frequency range
47 to 63 Hz
Number of phases
Single-phase
Inrush current
30 A (0 to P) or less, with cold start
Leakage current
0.75 mA or less
JST Mfg. Co., Ltd.
Part number
Applicable wiring
V1.25-M3 (round type)
V1.25-S3A (fork type)
0.35 to 1.65 mm2
V2-M3 (round type)
V2-S3A (fork type)
1.04 to 2.00 mm2
AWG #17 to #14
Output
24 V DC
Voltage accuracy
±5 %
Rated current
0.7 A (Note)
Output current range
0 to 0.6 A
500 mV or less
Ripple voltage
AWG #22 to #15
7.2 mm 0.28 in or less
Allow able momentary power off time 10 ms or more
Rated voltage
When CC-Link
slave unit with a
thermocouple unit
0 to 99.9 °C 32 to 211.82 °F
K, J and T
R
Standard
specifications
Protective Over-current protection 0.63 A or more
functions Over-voltage protection Available
Note: Start up may not be possible if a device with a large inrush current is connected even if below the rated
current. In such a case, we recommend suppressing the inrush current by inserting a 1 to 2 Ω resister
between the power supply unit and the device.
■ Current consumption
Type of unit
FP0R control
units
FP0R
expansion
units
16
C10
C14
C16
C32
T32
F32
AFP0RE8X
AFP0RE8R
AFP0RE8YR
AFP0RE8YT/P
AFP0RE16X
AFP0RE16R
AFP0RE16T/P
AFP0RE16YT/P
AFP0RE32T/P
Control unit current
consumption (24 V DC)
Expansion unit current
consumption (24 V DC)
100 mA or less
120 mA or less
70 mA or less
—
—
—
90 mA or less
—
10 mA or less
10 mA or less
10 mA or less
15 mA or less
10 mA or less
20 mA or less
—
50 mA or less
100 mA or less
20 mA or less
25 mA or less
35 mA or less
—
—
—
—
—
100 mA or less
Type of unit
Control unit current
consumption (24 V DC)
Expansion unit current
consumption (24 V DC)
20 mA or less
20 mA or less
100 mA or less
60 mA or less
100 mA or less
130 mA or less
FP0-A21
FP0-A80
FP0 intelligent FP0-A04V
units
FP0-A04I
FP0-TC4
FP0-TC8
FP0-CCLS
FP0-IOL
Communication
FP-WEB2
units
AFP15402
(C-NET adapter)
● Control unit current consumption
20 mA or less
20 mA or less
25 mA or less
—
40 mA or less
30 mA or less
40 mA or less
40 mA or less
—
95 mA or less (at 24 V DC)
240 mA or less (at 12 V DC)
50 mA or less
—
This refers to the current consumed via the power
supply connector of the control unit. If expansion
units or intelligent units are added, the current is
increased by the value indicated above.
● Expansion unit current consumption
This refers to the current consumed via the
power supply connector of the expansion unit.
Units with no value indication don't have a power
supply connector.
PRODUCT TYPES
Control units
Product name
FP0R-C10 Control Unit
Specications
Built-in memory
(Program capacity) Number of I/O points Power supply
Input
voltage
EEPROM
(16 k steps)
10
Input: 6
Output: 4
Output
24 V DC
24 V DC
Sink/Source
(±common)
24 V DC
24 V DC
Sink/Source
(±common)
Relay: 2 A
Relay: 2 A
Relay: 2 A
Relay: 2 A
10
Input: 6
Output: 4
FP0R-C10 Control Unit with RS485 port
EEPROM
(16 k steps)
10
Input: 6
Output: 4
24 V DC
24 V DC
Sink/Source
(±common)
FP0R-C14 Control Unit
EEPROM
(16 k steps)
14
Input: 8
Output: 6
24 V DC
24 V DC
Sink/Source
(±common)
24 V DC
24 V DC
Sink/Source
(±common)
Relay: 2 A
Relay: 2 A
FP0R-C10 Control Unit with RS232C port
EEPROM
(16 k steps)
FP0R-C14 Control Unit with RS232C port
EEPROM
(16 k steps)
14
Input: 8
Output: 6
Connection type
Terminal block
AFP0RC10RS
Molex connector
AFP0RC10RM
Terminal block
AFP0RC10CRS
Molex connector
AFP0RC10CRM
Terminal block
AFP0RC10MRS
Terminal block
AFP0RC14RS
Molex connector
AFP0RC14RM
Terminal block
AFP0RC14CRS
Molex connector
AFP0RC14CRM
Terminal block
AFP0RC14MRS
FP0R-C14 Control Unit with RS485 port
EEPROM
(16 k steps)
14
Input: 8
Output: 6
24 V DC
24 V DC
Sink/Source
(±common)
FP0R-C16 Control Unit
EEPROM
(16 k steps)
16
Input: 8
Output: 8
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
Input: 16
Output: 16
24 V DC
24 V DC Transistor NPN: 0.2 A
Sink/Source
(±common) Transistor PNP: 0.2 A
MIL connector
Power supply
voltage
Input
FP0R-C16 Control Unit with RS232C port
EEPROM
(16 k steps)
FP0R-C16 Control Unit with RS485 port
EEPROM
(16 k steps)
FP0R-C32 Control Unit
EEPROM
(32 k steps)
FP0R-C32 Control Unit with RS232C port
FP0R-C32 Control Unit with RS485 port
FP0R-T32 Control Unit with RS232C port and Real-time
clock function
EEPROM
(32 k steps)
EEPROM
(32 k steps)
EEPROM
(32 k steps)
FP0R-T32 Control Unit with RS485 port and Real-time
clock function
EEPROM
(32 k steps)
FP0R-F32 Control Unit with RS232C port and Battery-less
automatic all data backup function
EEPROM
(32 k steps)
FP0R-F32 Control Unit with RS485 port and Battery-less
automatic all data backup function
EEPROM
(32 k steps)
16
Input: 8
Output: 8
16
Input: 8
Output: 8
32
Input: 16
Output: 16
32
32
32
Input: 16
Output: 16
Input: 16
Output: 16
Input: 16
Output: 16
32
Input: 16
Output: 16
32
Input: 16
Output: 16
32
Part number
MIL connector
AFP0RC16T
AFP0RC16P
AFP0RC16CT
AFP0RC16CP
AFP0RC16MT
AFP0RC16MP
AFP0RC32T
AFP0RC32P
AFP0RC32CT
AFP0RC32CP
AFP0RC32MT
AFP0RC32MP
AFP0RT32CT
AFP0RT32CP
AFP0RT32MT
AFP0RT32MP
AFP0RF32CT
AFP0RF32CP
AFP0RF32MT
AFP0RF32MP
Notes: 1) See page 13 for the “Control unit replacement table” of the existing FP0 control units.
2) A power cable (Part number: AFPG805) is supplied with the control units.
Expansion units
Product name
FP0R-E8 Expansion Unit
FP0R-E16 Expansion Unit
Number of I/O points
Specications
Connection type
—
MIL connector
AFP0RE8X
8
Input: 8
—
8
Input: 4
Output: 4
24 V DC
24 V DC
Sink/Source
(±common)
Relay: 2 A
8
Output: 8
24 V DC
—
8
Output: 8
—
8
Output: 8
16
Input: 16
16
Input: 8
Output: 8
16
Input: 8
Output: 8
—
16
Input: 8
Output: 8
—
16
Output: 16
—
16
Output: 16
—
32
Input: 16
Output: 16
—
32
Input: 16
Output: 16
—
FP0R-E32 Expansion Unit
Part number
Output
24 V DC
Sink/Source
(±common)
Terminal block
AFP0RE8RS
Molex connector
AFP0RE8RM
Relay: 2 A
Terminal block
AFP0RE8YRS
—
Transistor NPN: 0.3 A
MIL connector
AFP0RE8YT
—
—
Transistor PNP: 0.3 A
MIL connector
AFP0RE8YP
—
24 V DC
Sink/Source
(±common)
—
24 V DC
24 V DC
Sink/Source
(±common)
Notes: 1) The relay output type expansion units come with a power cable (part number: AFP0581).
(The transistor output type expansion units need no power cable.)
2) The terminal block type relay output units have two terminal blocks (9 pins) made by Phoenix.
Use a 2.5 mm 0.10 inch wide screwdriver. Preferably use the specific terminal block screwdriver (part number:
AFP0806, Phoenix type code SZS0, 4 x 2.5 mm 0.10 inch) or equivalent.
24 V DC
Sink/Source
(±common)
24 V DC
Sink/Source
(±common)
Relay: 2 A
Transistor NPN: 0.3 A
MIL connector
AFP0RE16X
Terminal block
AFP0RE16RS
Molex connector
AFP0RE16RM
MIL connector
AFP0RE16T
Transistor PNP: 0.3 A
MIL connector
AFP0RE16P
—
Transistor NPN: 0.3 A
MIL connector
AFP0RE16YT
—
Transistor PNP: 0.3 A
MIL connector
AFP0RE16YP
Transistor NPN: 0.3 A
MIL connector
AFP0RE32T
Transistor PNP: 0.3 A
MIL connector
AFP0RE32P
24 V DC
Sink/Source
(±common)
24 V DC
Sink/Source
(±common)
3) The connector type relay output units have two connectors made by Nihon Molex (Molex type code
51067-0900, 9 pins). Use the specific Molex connector press-fit tool (part number: AFP0805, Nihon
Molex type code 57189-5000) or equivalent.
4) The transistor output units have a press-fit socket for wire-pressed terminal cable and contacts.
Use the press-fit tool (part number: AXY52000FP) for wire-pressed terminal cable.
17
PRODUCT TYPES
Intelligent units
Product name
FP0 Analog I/O Unit
Part number
FP0-A21
AFP0480
FP0-A80
AFP0401
Number or channels : 4 channels
Output range
: (Voltage output type) -10 to +10 V (Resolution: 1/4,000)
(Current output type) 4 to 20 mA (Resolution: 1/4,000)
FP0-A04V
AFP04121
FP0-A04I
AFP04123
K, J, T and R thermocouple, Resolution: 0.1°C
FP0-TC4
AFP0420
K, J, T and R thermocouple, Resolution: 0.1°C
FP0-TC8
AFP0421
Product number
Part number
FP0 Thermocouple Unit
Number or channels : 2 channels
Input range
: Voltage 0 to 5 V, -10 to +10 V (Resolution: 1/4,000)
Current 0 to 20 mA (Resolution: 1/4,000)
Number or channels : 1 channel
Output range
: Voltage -10 to +10 V (Resolution: 1/4,000)
Current 0 to 20 mA (Resolution: 1/4,000)
FP0 A/D Converter Unit
FP0 D/A Converter Unit
Product number
Specications
Number or channels : 8 channels
Input range
: Voltage 0 to 5 V, -10 to +10 V, -100 to 100 mV (Resolution: 1/4,000)
Current 0 to 20 mA (Resolution: 1/4,000)
Link and communication units
Product name
FP0 CC-Link Slave Unit
Power supply
voltage
Specications
This unit is for making the FP0 function as a slave station of the CC-Link.
Only one unit can be connected to the furthest right edge of the FP0 expansion bus.
Note: Accuracy will change if an FP0 thermocouple unit is used at the same time.
For details, please refer to the catalog or to the CC-Link Unit manual.
24 V DC
FP0-CCLS
AFP07943
FP0-IOL
AFP0732
FP0 I/O Link Unit
This is a link unit designed to make the FP0 function as a station to MEWNET-F (remote
I/O system).
24 V DC
KS1 Signal Converter
RS232C/RS485 data can be easily monitored by LAN.
24 V DC
AKS1202
C-NET Adapter
(for computer side)
This is an RS485 adapter designed to allow use of the computer link function for
connecting to a network-connected PLC via C-NET from a host computer.
100 to 240 V AC
AFP8536
24 V DC
AFP8532
FP Web-Server 2 Unit
Unit for connecting FP series or RS232C interface device and Ethernet
Web-server function and E-mail sending function
24 V DC
FP-WEB2
AFP0611
Product number
Part number
FP0-PSA4
AFP0634
Power supply unit and others
Product name
FP0 Power Supply Unit
FP Memory Loader
Specications
Input voltage: 100 to 240 V AC
Output capacity: 24 V DC, 0.7 A
Data clear type
AFP8670
Data hold type
AFP8671
Programming tools
Specications
Product name
Windows version tool software
Control FPWIN Pro Ver.6
(Conforms to IEC61131-3)
(FP0R is compatible with Ver. 6.1 or later.)
Japanese version, Full type
CD-ROM for Windows
AFPS50160
English version, Full type
CD-ROM for Windows
AFPS50560
Japanese tool kit with cable
Windows version tool software
Control FPWIN GR
(FP0R is compatible with Ver. 2.8 or later.)
Handheld programmer
18
Part number
CD-ROM for Windows, with cable (AFC8503)
for connection of FP to DOS/V PC
AFPS10122
English version, Full type
CD-ROM for Windows
AFPS10520
English version, Small type
CD-ROM for Windows
AFPS11520
Chinese version, Full type
CD-ROM for Windows
AFPS10820
Korean
CD-ROM for Windows
AFPS10920
Not available for FP0R. Also the discontinued models (AFP1113V2 and AFP1114V2) are not compatible with FP0R. (They are compatible with FP0.)
Options and maintenance parts
Product name
Specications
Part number
Data clear type
AFP8670
Data hold type
AFP8671
Terminal screwdriver
Relay output type Necessary when wiring terminals block (Phoenix).
AFP0806
Molex connector pressure contact tool
Necessary when wiring relay output type and Molex connectors. (MOLEX: 57189-5000)
Multi-wire connector pressure contact tool
Necessary when wiring transistor output type connectors.
FP0 Slim type Mounting plate
Screw-stop attachment plate for FP0 expansion unit. Slim model.
FP0 Flat type Mounting plate
Screw-stop attachment plate for FP0 control unit. Flat model.
FP Memory Loader (Note)
AFP0805
AXY52000FP
AFP0803 (set for 10)
AFP0804 (set for 10)
Loose-wiring cable (9 leads) with molex socket attached at one end, AWG20, 0.5 mm2,
Length: 1 m 3.3 ft
AFP0551 (2 cables set)
1 set: 2 cables (blue & white).
Length: 3 m 9.8 ft
AFP0553 (2 cables set)
Transistor output type I/O Cable
Loose-wiring cable (10 leads) with connectors attached at one end, AWG22, 0.3 mm2,
1 set: 2 cables (blue & white)
Length: 1 m 3.3 ft
AFP0521 (2 cables set)
Flat cable connector set
Flat cable connector set (10 leads)
AFP0808 (including 4 pieces)
Terminal socket
Attaches to relay output and terminal block type. Maintenance part
AFP0802 (2 sokets per pack)
Molex socket
Attaches to relay output and Molex connector types. Maintenance part
AFP0801 (2 sokets per pack)
Wire-press socket
Attaches to transistor output type. Maintenance part
AFP0807 (2 sokets per pack)
Power cable for conrol unit
Attaches to FP0R control unit. Maintenance part Length: 1 m 3.3 ft
AFPG805 (1 cable per pack)
Power cable for expansion unit
Attaches to expansion unit. Maintenance part Length: 1 m 3.3 ft
AFP0581 (1 cable per pack)
Relay output Molex type I/O cable
Length: 3 m 9.8 ft
AFP0523 (2 cables set)
Note: FP0R is compatible with Ver. 2 or later.
19
DIMENSIONS
■ Control units and Expansion units
(Unit: mm in)
* For the relay output type, the terminal block type is listed as the representative type.
C10RS, C10RM, C10CRS, C10CRM, C10MRS,
C14RS, C14RM, C14CRS, C14CRM and
C14MRS
60.0
2.36
(10)
(0.39)
25.0
0.98
(Note 1)
90.0
3.54
E8RS, E8RM, E8YRS, E16RS and E16RM
(9)
(0.35)
Output terminal block
RS232C port (C10CR and C14CR only)
RS485 port (C10MR and C14MR only)
Control units
3.5
0.14
60.0
2.36
Input connector
(7.5)
(0.30)
(10)
(0.39) 13.0
0.51
Notes: 1) DIN rail is attached on the center of the unit.
2) The AFP0RE8YRS is not equipped with an input terminal block.
C16T, C16P, C16CT, C16CP, C16MT and C16MP
C10RS/C10RM C14RS/C14RM E8RS/E8RM E16RS/E16RM/
E8YRS
60.0
2.36
90.0
3.54
Expansion units
● Terminal array
Input terminal block
(18)
(0.71)
(4.5)
(0.18)
DIN standard rail
Control units
(9)
(0.35)
(7.5)
(0.30)
(4.5)
(0.18)
(10)
DIN standard rail
(0.39) 13.0 (DIN EN50022 35 mm 1.38 in width)
0.51
30.0 (Note 2)
1.18
Input connector
60.0
2.36
(18)
(0.71)
(Note 1)
90.0
3.54
130.0
5.12
approx.
E32T, E32P, E16X, E16YT and E16YP
Output connector
Notes: 1) DIN rail is attached on the center of the unit.
2) The AFP0RE32T, AFP0RE32P, AFP0RE16X, AFP0RE16YT and AFP0RE16YP are
25 mm 0.98 in each.
3) The AFP0RE16X has no output connector.
4) The AFP0RE16YT and AFP0RE16YP has no input connector.
■ FP0 Analog I/O Unit and
D/A Converter Unit
■ FP0 A/D Converter Unit
(10)
(0.39)
60.0
2.36
25
0.98
(10)
(0.39)
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
COM
(9)
(0.35)
Y0
Y2
Y4
Y6
(+)
(7.5)
(0.30)
(4.5)
(0.18)
(10)
DIN standard rail
(0.39) 13.0 (DIN EN50022 35 mm 1.38 in width)
0.51
25.0
0.98
X1
X3
X5
X7
COM
SG
RD
SD
Y1
Y3
Y5
Y7
(–)
−
E
+
Note: Two COM terminals on the input circuit are connected
inside the unit.
X0
X2
X4
X6
COM
● RS232C port Terminal array
8.50
0.33
X1
X3
X5
X7
COM
X8
XA
XC
XE
COM
X9
XB
XD
XF
COM
SG
RD
SD
Output (16 points / common) ● RS485 port Terminal array
Y0
Y2
Y4
Y6
(+)
Y1
Y3
Y5
Y7
(–)
Y8
YA
YC
YE
(+)
Y9
YB
YD
YF
(–)
−
E
+
Notes: 1) Four COM terminals on the input circuit are
connected inside the unit.
2) Two (+) terminals and two (-) terminals on the output
circuit are connected respectively inside the unit.
■ FP0 Power Supply
Unit
60.0
2.36
● RS232C port Terminal array
Output (8 points / common) ● RS485 port Terminal array
■ FP Web-Server 2 Unit
and Thermocouple Unit
25.0
0.98
RS232C port (C32C, T32C and F32C only)
RS485 port (C32M, T32M, F32M only)
Y0
Y1
Y2
Y3
(NC)
(NC)
(NC)
(NC)
COM
Input (16 points / common)
90.0
3.54
Expansion units
Y0
Y1
Y2
Y3
COM
Y4
COM
Y5
COM
● Terminal array
60.0
2.36
3.5
0.14
C32T, C32CT, C32P, C32CP, C32MT, C32MP,
T32CT, T32CP, T32MT, T32MP,
F32CT, F32CP, F32MT and F32MP
Y0
Y1
(NC)
(NC)
COM
Y2
COM
Y3
COM
X0
X2
X4
X6
COM
130.0
5.12
approx.
Output connector
X0
X1
X2
X3
X4
X5
X6
X7
COM
Input (8 points / common)
(Note 1)
90.0
3.54
RS232C port (C16C only)
RS485 port (C16M only)
X0
X1
X2
X3
(NC)
(NC)
(NC)
(NC)
COM
● Terminal array
60.0
2.36
90.0
3.54
Notes: 1) DIN rail is attached on the center of the unit.
2) The AFP0RE8X has no output connector.
3) The AFP0RE8YT and AFP0RE8YP has no input connector.
X0
X1
X2
X3
X4
X5
X6
X7
COM
(DIN EN50022 35 mm 1.38 in width)
Expansion units
E16T, E16P, E8X, E8YT and E8YP
X0
X1
X2
X3
X4
X5
(NC)
(NC)
COM
130.0
5.12
approx.
25.0
0.98
Input
3.5
0.14
Output
Control units
60.0
2.36
35.0
1.38
19.2
0.76
60.0
2.36
EXPANSION
CONNECTOR
MODE
1
2
3
4
5
OFF ON
90.0
3.54
V0
I 0
IN COM
V1
90.0
3.54
90.0
3.54
I 1
90.0
Input
terminal 3.54
Connection
terminal
V
OUT
I
COM
FP0 - A21
Output
terminal
3.5
0.14
4.5
0.18
4.5
0.18
3.5
0.14
3.5
0.14
■ External Dimensions During Expansions
A + B + C + D dimensions (mm in)
● Top view (with DIN rail attached)
A
(67.5)
(2.66)
60.0
2.36
● Front view
B
A
XO-7
X8-F
XO-7
X8-F
0
RUN
C
XO-7
B
B
P ROG.
YO-7
Y8-F
YO-7
Y8-F
1
4
4
2011.08
4
5
6
7
8
7
90.0
3.54
8
9
A
9
A
B
C
B
C
D
E
F
3
5
6
9
B
D
E
1
2
4
5
A
C
F
1
3
7
8
9
B
D
Y8-F
0
2
6
7
8
E
F
YO-7
1
5
6
A
C
Y8-F
3
(45)
(1.77)
E
0
2
3
D
F
YO-7
0
2
9
B
C
E
F
0
5
7
B
D
E
F
A
C
D
E
3
8
9
A
C
D
6
7
8
9
A
C
1
2
4
5
6
7
8
9
0
3
4
5
6
7
8
X8-F
1
2
3
4
5
6
A
RUN
XO-7
0
1
2
3
4
ALARM
X8-F
0
1
2
PROG
ERROR
D
D
E
F
F
(45)
(1.77)
A→B
A→C
A→D
Control unit 1 expansion
2 expansion
3 expansion
only
unit connected units connected units connected
Control unit
C10RS
C10CRS
C10RM
C10CRM
C10MRS
C14RS
C14CRS
C14RM
C14CRM
C14MRS
C16T
C16CT
C16P
C16CP
C16MT
C16MP
C32T
C32CT
C32P
C32CP
T32CT
T32CP
F32CT
F32CP
C32MT
C32MP
T32MT
T32MP
F32MT
F32MP
25
0.98
50
1.97
75
2.95
100
3.94
30
1.18
55
2.17
80
3.15
105
4.13
panasonic-electric-works.net/sunx
Panasonic Electric Works SUNX Co., Ltd.
Global Sales & Marketing Division
No. CE-FP0R-9 August, 2011
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
■Telephone: +81-568-33-7861 ■Facsimile: +81-568-33-8591
All Rights Reserved ©Panasonic Electric Works SUNX Co., Ltd. 2011
工商网监
湘ICP备2023018690号
