EEE-FK1E330V

Aluminum Electrolytic Capacitors Surface Mount Type FK series Features ● Endurance：105 ℃ 2000 h to 5000 h ● Low impedance（40 % to 60 % less than FC series） ● Miniaturized (30 % to 50 % less than FC series) ● Vibration-proof product (30G guaranteed) is available upon request（ø6.3 ≦） ● AEC-Q200 compliant ● RoHS compliant Specifications Category temp. range Rated voltage range Capacitance range Capacitance tolerance Leakage current Dissipation factor (tan δ) Characteristics at low temperature Endurance Shelf life Resistance to soldering heat –55 ℃ to +105 ℃ 6.3 V to 100 V 3.3 μF to 6800 μF ±20 % (120 Hz / +20 ℃) I ≦ 0.01 CV or 3 (μA) After 2 minutes (Whichever is greater) Please see the attached characteristics list Rated voltage (V) 6.3 10 16 25 35 50 63 80 100 2 2 2 2 2 2 2 2 2 Z (–25 ℃) / Z (+20 ℃) (Impedance ratio at 120 Hz) 3 3 3 3 3 3 3 3 3 Z (–40 ℃) / Z (+20 ℃) 4 4 4 3 3 3 3 3 3 Z (–55 ℃) / Z (+20 ℃) After applying rated working voltage for 2000 hours at +105 ℃ ± 2 ℃ and then being stabilized at +20 ℃, capacitors shall meet the following limits. （≧ ø12.5 and suffix “G” in ø8×10.2, ø10×10.2 are 5000 hours） Capacitance change Within ±30 % of the initial value (Suffix “G” is 35 %) Dissipation factor（tan δ) ≦ 200 % of the initial limit (Suffix “G” is 300 %) Leakage current Within the initial limit After storage for 1000 hours at +105 ℃ ± 2 ℃ with no voltage applied and then being stabilized at +20 ℃, capacitors shall meet the limits specified in endurance. (With voltage treatment) After reflow soldering and then being stabilized at +20 ℃, capacitors shall meet the following limits. Capacitance change Within ±10 % of the initial value Within the initial limit Dissipation factor（tan δ) Leakage current Within the initial limit Frequency correction factor for ripple current Frequency (Hz) Correction factor 50, 60 0.70 120 0.75 j FK 6.3 10 16 25 35 Size code Series identification Unit：V H J K 2A （I） （P） （）Reference size Unit：mm Capacitance (μF) Rated voltage code j A C E V W Pressure Relief (ø10 and larger) Lot number R. voltage code H L Rated voltage code Negative polarity marking (–) 3300 B±0.2 Mark for Lead-Free products (Black dot) A±0.2 （I） Lot number Series identification øD±0.5 0.3 max. Negative polarity marking (–) Capacitance (μF) 22 j FK ≧ ø12.5 100 k to 1.00 Dimensions Example : 6.3 V 22 μF, 6.3 V 3300 μF Marking color : BLACK ≦ ø10 10 k 0.95 K Marking 1k 0.90 50 63 80 100 B C D D8 E F G H13 J16 K16 øD 4.0 5.0 6.3 6.3 8.0 8.0 10.0 12.5 16.0 18.0 L 5.8±0.3 5.8±0.3 5.8±0.3 7.7±0.3 6.2±0.3 10.2±0.3 10.2±0.3 13.5±0.5 16.5±0.5 16.5±0.5 A, B 4.3 5.3 6.6 6.6 8.3 8.3 10.3 13.5 17.0 19.0 H 5.5 max. 6.5 max. 7.8 max. 7.8 max. 9.5 max. 10.0 max. 12.0 max. 15.0 max. 19.0 max. 21.0 max. I 1.8 2.2 2.6 2.6 3.4 3.4 3.5 4.7 5.5 6.7 W 0.65±0.1 0.65±0.1 0.65±0.1 0.65±0.1 0.65±0.1 0.90±0.2 0.90±0.2 0.90±0.3 1.20±0.3 1.20±0.3 P 1.0 1.5 1.8 1.8 2.2 3.1 4.6 4.4 6.7 6.7 K 0.35 +0.15 ー0.20 0.35 +0.15 ー0.20 0.35 +0.15 ー0.20 0.35 +0.15 ー0.20 0.35 +0.15 ー0.20 0.70±0.2 0.70±0.2 0.70±0.3 0.70±0.3 0.70±0.3 ・The dimensions of the vibration-proof products, please refer to the page of the mounting specification. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06-Dec-19 Aluminum Electrolytic Capacitors (SMD Type) Dimensions (Vibration-proof products) ✽ The size and shape are different from standard products. Please inquire details of our company. < Size code：E, F, G, H13, J16, K16, K21 > Supportive Terminals K R W *1：E to G : L±0.3 ( ) Reference size Size code D D8 E F G H13 J16 K16 K21 øD 6.3 6.3 8.0 8.0 10.0 12.5 16.0 18.0 18.0 L A, B 6.1 8.0 6.5 10.5 10.5 13.8 16.8 16.8 21.8 6.6 6.6 8.3 8.3 10.3 13.5 17.0 19.0 19.0 7.8 7.8 9.5 10.0 12.0 15.0 19.0 21.0 21.0 (I) (I) T L*1 ( ) Reference size Supportive Terminals ※The diagram is not drawn to scale. H max. (P) B±0.2 (S) H øD±0.5 (P) R T W L±0.3 A±0.2 (I) K F (S) B±0.2 A±0.2 H øD±0.5 F (I) < Size code：D, D8 > Unit：ｍｍ F I 0 to +0.15 0 to +0.15 0 to +0.15 0 to +0.15 0 to +0.15 –0.1 to +0.15 –0.1 to +0.15 –0.1 to +0.15 –0.1 to +0.15 2.4 2.4 3.4 3.4 3.5 4.7 5.5 6.7 6.7 W P 0.65±0.1 0.65±0.1 0.7±0.1 1.2±0.2 1.2±0.2 1.2±0.2 1.4±0.2 1.4±0.2 1.4±0.2 2.2 2.2 2.2 3.1 4.6 4.4 6.7 6.7 6.7 K +0.15 －0.20 +0.15 －0.20 +0.15 －0.20 0.35 0.35 0.35 0.70±0.2 0.70±0.2 0.70±0.3 0.70±0.3 0.70±0.3 0.70±0.3 R S T 1.1±0.2 1.1±0.2 0.70±0.2 0.70±0.2 0.70±0.2 2.2±0.2 3.0±0.2 3.0±0.2 3.0±0.2 3.3 3.3 5.3 5.3 6.9 7.1 9.0 11.0 11.0 1.05±0.2 1.05±0.2 1.7±0.2 1.3±0.2 1.3±0.2 2.4±0.2 1.9±0.2 1.9±0.2 1.9±0.2 Land / Pad pattern The circuit board land/pad pattern size for chip capacitors is specified in the following table. The land pitch influences installation strength and consider it. （Table of board land size vs. capacitor size） Size code ● Standard products c b B (ø4) C (ø5) D (ø6.3) D8 (ø6.3x7.7L) E (ø8x6.2L) F (ø8x10.2L) G (ø10x10.2L) H (ø12.5) J (ø16) K (ø18) b a Land space ● Vibration-proof products C H G A A B Size code B c 2.5 2.8 3.2 3.2 4.0 4.0 4.1 5.7 6.5 7.5 1.6 1.6 1.6 1.6 1.6 2.0 2.0 2.0 2.5 2.5 G H D (ø6.3xL6.1） D8 (ø6.3xL8.0） E (ø8x6.5L) F (ø8x10.5L) G (ø10) H (ø12.5) J (ø16) K (ø18) A 1.2 1.2 1.8 2.7 3.9 3.9 5.8 5.8 B 3.6 3.6 4.2 4.0 4.4 6.0 6.8 7.3 C 3.2 3.2 5.0 4.7 4.7 6.9 6.2 6.2 D E Unit：ｍｍ F G 2.0 0.95 0.65 1.0 2.0 0.95 0.65 1.0 1.3 1.5 1.4 1.5 1.3 1.0 1.7 1.1 1.3 1.2 1.9 1.1 2.8 1.3 1.9 2.2 3.6 1.3 1.9 1.7 3.6 1.8 1.9 1.7 H 1.2 1.2 2.0 2.5 2.5 2.5 2.8 2.8 When size “A” is wide, back fi llet can be made, decreasing fi tting strength. C G F < Size code：E, F, G, H, J, K > C 1.0 1.5 1.8 1.8 2.2 3.1 4.6 4.0 6.0 6.0 （Table of board land size vs. capacitor size） F G E D C Unit：ｍｍ b When size “a” is wide, back fi llet can be made, decreasing fi tting strength. B < Size code：D, D8 > a ＊Take mounting conditions, solderability and fi tting strength into B D B consideration when selecting parts for your company’s design. ＊ The vibration-proof capacitors of size ø6.3 has support terminals extending A E A from the bottom side to the lead edge. Then, make sure to find appropriate soldering conditions to form fillet on the support terminals if B required for appearance inspection. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01-Apr-22 FK series Characteristics list Endurance : 105 ℃ 2000 h (≧ ø12.5 : 5000 h) Capacitance (±20 %) (μF) 22 47 100 6.3 220 330 470 1000 1500 3300 6800 22 33 150 220 10 330 470 680 1000 2200 4700 6800 10 22 47 16 68 100 150 220 330 470 680 1500 3300 4700 10 22 33 47 68 25 100 150 220 330 470 1000 1500 2200 3300 L øD 4.0 4.0 5.0 5.0 6.3 6.3 6.3 8.0 8.0 8.0 10.0 12.5 16.0 4.0 4.0 5.0 6.3 6.3 8.0 8.0 8.0 8.0 10.0 12.5 16.0 18.0 4.0 4.0 5.0 5.0 6.3 6.3 6.3 6.3 6.3 8.0 8.0 8.0 10.0 12.5 16.0 18.0 4.0 5.0 5.0 6.3 6.3 6.3 6.3 8.0 8.0 8.0 8.0 10.0 12.5 16.0 16.0 18.0 Standard Vibrationproof 5.8 5.8 5.8 5.8 5.8 5.8 7.7 6.2 10.2 10.2 10.2 13.5 16.5 5.8 5.8 5.8 5.8 7.7 6.2 10.2 10.2 10.2 10.2 13.5 16.5 16.5 5.8 5.8 5.8 5.8 5.8 5.8 5.8 7.7 7.7 6.2 10.2 10.2 10.2 13.5 16.5 16.5 5.8 5.8 5.8 5.8 5.8 5.8 7.7 6.2 10.2 10.2 10.2 10.2 13.5 16.5 16.5 16.5 ー ー ー ー 6.1 6.1 8.0 6.5 10.5 10.5 10.5 13.8 16.8 ー ー ー 6.1 8.0 6.5 10.5 10.5 10.5 10.5 13.8 16.8 16.8 ー ー ー ー 6.1 6.1 6.1 8.0 8.0 6.5 10.5 10.5 10.5 13.8 16.8 16.8 ー ー ー 6.1 6.1 6.1 8.0 6.5 10.5 10.5 10.5 10.5 13.8 16.8 16.8 16.8 B (B) C (C) D D D8 E F F G H13 J16 B (B) C D D8 E F F F G H13 J16 K16 B (B) C (C) D D D D8 D8 E F F G H13 J16 K16 B C (C) D D D D8 E F F F G H13 J16 J16 K16 Specification Ripple current*2 (mA rms) 90 90 160 160 240 240 280 300 600 600 850 1100 1800 90 90 160 240 280 300 600 600 600 850 1100 1800 2060 90 90 160 160 240 240 240 280 280 300 600 600 850 1100 1800 2060 90 160 160 240 240 240 280 300 600 600 600 850 1100 1800 1800 2060 Impe- *3 dance (Ω) 1.35 1.35 0.70 0.70 0.36 0.36 0.34 0.26 0.16 0.16 0.08 0.06 0.035 1.35 1.35 0.70 0.36 0.34 0.26 0.16 0.16 0.16 0.08 0.06 0.035 0.033 1.35 1.35 0.70 0.70 0.36 0.36 0.36 0.34 0.34 0.26 0.16 0.16 0.08 0.06 0.035 0.033 1.35 0.70 0.70 0.36 0.36 0.36 0.34 0.26 0.16 0.16 0.16 0.08 0.06 0.035 0.035 0.033 Part No. tan δ*4 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.30 0.36 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.21 0.25 0.29 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.20 0.22 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.14 0.16 0.18 Standard Product EEEFK0J220R EEEFK0J470UR EEEFK0J470R EEEFK0J101UR EEEFK0J101P EEEFK0J221P EEEFK0J331XP EEEFK0J331P EEEFK0J471P EEEFK0J102P EEEFK0J152P EEVFK0J332Q EEVFK0J682M EEEFK1A220R EEEFK1A330UR EEEFK1A330R EEEFK1A151P EEEFK1A221XP EEEFK1A221P EEEFK1A331P EEEFK1A471P EEEFK1A681P EEEFK1A102P EEVFK1A222Q EEVFK1A472M EEVFK1A682M EEEFK1C100R EEEFK1C220UR EEEFK1C220R EEEFK1C470UR EEEFK1C470P EEEFK1C680P EEEFK1C101P EEEFK1C151XP EEEFK1C221XP EEEFK1C221P EEEFK1C331P EEEFK1C471P EEEFK1C681P EEVFK1C152Q EEVFK1C332M EEVFK1C472M EEEFK1E100R EEEFK1E220R EEEFK1E330UR EEEFK1E330P EEEFK1E470P EEEFK1E680P EEEFK1E101XP EEEFK1E101P EEEFK1E151P EEEFK1E221P EEEFK1E331P EEEFK1E471P EEVFK1E102Q EEVFK1E152M EEVFK1E222M EEVFK1E332M Vibration-proof product ー ー ー ー EEEFK0J101V EEEFK0J221V EEEFK0J331XV EEEFK0J331V EEEFK0J471V EEEFK0J102V EEEFK0J152V EEVFK0J332V EEVFK0J682V ー ー ー EEEFK1A151V EEEFK1A221XV EEEFK1A221V EEEFK1A331V EEEFK1A471V EEEFK1A681V EEEFK1A102V EEVFK1A222V EEVFK1A472V EEVFK1A682V ー ー ー ー EEEFK1C470V EEEFK1C680V EEEFK1C101V EEEFK1C151XV EEEFK1C221XV EEEFK1C221V EEEFK1C331V EEEFK1C471V EEEFK1C681V EEVFK1C152V EEVFK1C332V EEVFK1C472V ー ー ー EEEFK1E330V EEEFK1E470V EEEFK1E680V EEEFK1E101XV EEEFK1E101V EEEFK1E151V EEEFK1E221V EEEFK1E331V EEEFK1E471V EEVFK1E102V EEVFK1E152V EEVFK1E222V EEVFK1E332V Reflow Rated voltage (V) (mm) Size code*1 Case size Min. Packaging Q'ty (pcs) Taping (1) (1) (1) (1) (1) (1) (1) (2) (2) (2) (2) (3) (3) (1) (1) (1) (1) (1) (2) (2) (2) (2) (2) (3) (3) (3) (1) (1) (1) (1) (1) (1) (1) (1) (1) (2) (2) (2) (2) (3) (3) (3) (1) (1) (1) (1) (1) (1) (1) (2) (2) (2) (2) (2) (3) (3) (3) (3) 2000 2000 1000 1000 1000 1000 900 1000 500 500 500 200 125 2000 2000 1000 1000 900 1000 500 500 500 500 200 125 125 2000 2000 1000 1000 1000 1000 1000 900 900 1000 500 500 500 200 125 125 2000 1000 1000 1000 1000 1000 900 1000 500 500 500 500 200 125 125 125 *1: Size code( ): Miniaturization product *2: Ripple current (100 kHz / +105 ℃） *3: Impedance (100 kHz / +20 ℃) *4: tan δ (120 Hz / +20 ℃) ・ Please refer to the page of "Reflow Profile" and "The Taping Dimensions". Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06-Dec-19 FK series Characteristics list Endurance : 105 ℃ 2000 h (≧ ø12.5 : 5000 h) Capacitance (±20 %) (μF) 4.7 10 22 33 47 68 35 100 150 220 330 470 680 1000 1500 4.7 10 22 33 47 50 100 150 220 330 390 470 560 680 1000 4.7 10 22 63 33 47 68 100 150 220 470 680 3.3 4.7 10 80 22 33 47 68 100 150 330 470 L øD 4.0 4.0 5.0 5.0 6.3 6.3 6.3 6.3 8.0 8.0 8.0 10.0 12.5 12.5 16.0 16.0 4.0 5.0 6.3 6.3 6.3 8.0 6.3 8.0 8.0 10.0 10.0 12.5 12.5 16.0 16.0 16.0 16.0 5.0 6.3 6.3 8.0 8.0 8.0 8.0 10.0 12.5 12.5 16.0 18.0 5.0 6.3 6.3 8.0 8.0 8.0 10.0 12.5 12.5 12.5 16.0 18.0 Standard Vibrationproof 5.8 5.8 5.8 5.8 5.8 5.8 7.7 7.7 10.2 10.2 10.2 10.2 13.5 13.5 16.5 16.5 5.8 5.8 5.8 5.8 7.7 6.2 7.7 6.2 10.2 10.2 10.2 13.5 13.5 16.5 16.5 16.5 16.5 5.8 5.8 7.7 6.2 10.2 10.2 10.2 10.2 13.5 13.5 16.5 16.5 5.8 5.8 7.7 6.2 10.2 10.2 10.2 13.5 13.5 13.5 16.5 16.5 ー ー ー ー 6.1 6.1 8 8 10.5 10.5 10.5 10.5 13.8 13.8 16.8 16.8 ー ー 6.1 6.1 8 6.5 8 6.5 10.5 10.5 10.5 13.8 13.8 16.8 16.8 16.8 16.8 ー 6.1 8 6.5 10.5 10.5 10.5 10.5 13.8 13.8 16.8 16.8 ー 6.1 8 6.5 10.5 10.5 10.5 13.8 13.8 13.8 16.8 16.8 B (B) C C D D D8 D8 F F F G H13 H13 J16 J16 B (C) D D D8 E D8 E F G G H13 H13 J16 J16 J16 J16 C D D8 E F F (F) G H13 H13 J16 K16 C D D8 E F F G H13 H13 H13 J16 K16 Specification Ripple current*2 (mA rms) 90 90 160 160 240 240 280 280 600 600 600 850 1100 1100 1800 1800 60 85 165 165 195 195 195 195 350 670 670 900 900 1610 1610 1610 1610 50 80 120 120 250 250 250 400 800 800 1410 1690 25 40 60 60 130 130 200 500 500 500 793 917 Impe- *3 dance (Ω) 1.35 1.35 0.70 0.70 0.36 0.36 0.34 0.34 0.16 0.16 0.16 0.08 0.06 0.06 0.035 0.035 2.90 1.52 0.88 0.88 0.68 0.68 0.68 0.68 0.34 0.18 0.18 0.12 0.12 0.073 0.073 0.073 0.073 3.00 1.50 1.20 1.20 0.65 0.65 0.65 0.35 0.16 0.16 0.082 0.08 5.00 3.00 2.40 2.40 1.30 1.30 0.70 0.32 0.32 0.32 0.17 0.153 Part No. tan δ*4 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 Standard Product EEEFK1V4R7R EEEFK1V100UR EEEFK1V100R EEEFK1V220R EEEFK1V330P EEEFK1V470P EEEFK1V680XP EEEFK1V101XP EEEFK1V101P EEEFK1V151P EEEFK1V221P EEEFK1V331P EEVFK1V471Q EEVFK1V681Q EEVFK1V102M EEVFK1V152M EEEFK1H4R7R EEEFK1H100UR EEEFK1H100P EEEFK1H220P EEEFK1H330XP EEEFK1H330P EEEFK1H470XP EEEFK1H470P EEEFK1H101P EEEFK1H151P EEEFK1H221P EEVFK1H331Q EEVFK1H391Q EEVFK1H471M EEVFK1H561M EEVFK1H681M EEVFK1H102M EEEFK1J4R7R EEEFK1J100P EEEFK1J220XP EEEFK1J220P EEEFK1J330P EEEFK1J470P EEEFK1J680UP EEEFK1J101P EEVFK1J151Q EEVFK1J221Q EEVFK1J471M EEVFK1J681M EEEFK1K3R3R EEEFK1K4R7P EEEFK1K100XP EEEFK1K100P EEEFK1K220P EEEFK1K330P EEEFK1K470P EEVFK1K680Q EEVFK1K101Q EEVFK1K151Q EEVFK1K331M EEVFK1K471M Vibration-proof product ー ー ー ー EEEFK1V330V EEEFK1V470V EEEFK1V680XV EEEFK1V101XV EEEFK1V101V EEEFK1V151V EEEFK1V221V EEEFK1V331V EEVFK1V471V EEVFK1V681V EEVFK1V102V EEVFK1V152V ー ー EEEFK1H100V EEEFK1H220V EEEFK1H330XV EEEFK1H330V EEEFK1H470XV EEEFK1H470V EEEFK1H101V EEEFK1H151V EEEFK1H221V EEVFK1H331V EEVFK1H391V EEVFK1H471V EEVFK1H561V EEVFK1H681V EEVFK1H102V ー EEEFK1J100V EEEFK1J220XV EEEFK1J220V EEEFK1J330V EEEFK1J470V EEEFK1J680UV EEEFK1J101V EEVFK1J151V EEVFK1J221V EEVFK1J471V EEVFK1J681V ー EEEFK1K4R7V EEEFK1K100XV EEEFK1K100V EEEFK1K220V EEEFK1K330V EEEFK1K470V EEVFK1K680V EEVFK1K101V EEVFK1K151V EEVFK1K331V EEVFK1K471V Reflow Rated voltage (V) (mm) Size code*1 Case size Min. Packaging Q'ty (pcs) Taping (1) (1) (1) (1) (1) (1) (1) (1) (2) (2) (2) (2) (3) (3) (3) (3) (1) (1) (1) (1) (1) (2) (1) (2) (2) (2) (2) (3) (3) (3) (3) (3) (3) (1) (1) (1) (2) (2) (2) (2) (2) (3) (3) (3) (3) (1) (1) (1) (2) (2) (2) (2) (3) (3) (3) (3) (3) 2000 2000 1000 1000 1000 1000 900 900 500 500 500 500 200 200 125 125 2000 1000 1000 1000 900 1000 900 1000 500 500 500 200 200 125 125 125 125 1000 1000 900 1000 500 500 500 500 200 200 125 125 1000 1000 900 1000 500 500 500 200 200 200 125 125 *1: Size code( ): Miniaturization product *2: Ripple current (100 kHz / +105 ℃） *3: Impedance (100 kHz / +20 ℃) *4: tan δ (120 Hz / +20 ℃) ・ Please refer to the page of "Reflow Profile" and "The Taping Dimensions". Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06-Dec-19 FK series Characteristics list Endurance : 105 ℃ 2000 h (≧ ø12.5 : 5000 h) 100 Capacitance (±20 %) (μF) L øD Standard Vibrationproof Specification Ripple current*1 (mA rms) Impe- *2 dance (Ω) Part No. tan δ*3 Standard Product Vibration-proof product Reflow Rated voltage (V) (mm) Size code Case size Min. Packaging Q'ty (pcs) Taping 22 8.0 10.2 10.5 F 130 1.30 0.07 EEEFK2A220P EEEFK2A220V (2) 500 33 10.0 10.2 10.5 G 200 0.70 0.07 EEEFK2A330P EEEFK2A330V (2) 500 47 12.5 13.5 13.8 H13 500 0.32 0.07 EEVFK2A470Q EEVFK2A470V (3) 200 68 12.5 13.5 13.8 H13 500 0.32 0.07 EEVFK2A680Q EEVFK2A680V (3) 200 100 16.0 16.5 16.8 J16 793 0.17 0.07 EEVFK2A101M EEVFK2A101V (3) 125 150 16.0 16.5 16.8 J16 793 0.17 0.07 EEVFK2A151M EEVFK2A151V (3) 125 220 18.0 16.5 16.8 K16 917 0.153 0.07 EEVFK2A221M EEVFK2A221V (3) 125 330 18.0 16.5 16.8 K16 917 0.153 0.07 EEVFK2A331M EEVFK2A331V (3) 125 Endurance： 105 ℃ 5000 h 6.3 10 16 25 35 50 Capacitance (±20 %) (μF) 470 1000 1500 330 470 680 1000 330 470 680 150 220 330 470 100 150 220 330 100 150 220 L øD 8.0 8.0 10.0 8.0 8.0 8.0 10.0 8.0 8.0 10.0 8.0 8.0 8.0 10.0 8.0 8.0 8.0 10.0 8.0 10.0 10.0 Standard Vibrationproof 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.2 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 Specification Ripple current*1 (mA rms) F F G F F F G F F G F F F G F F F G F G G 600 600 850 600 600 600 850 600 600 850 600 600 600 850 600 600 600 850 350 670 670 Part No. Impedance*2 (Ω) tan δ*3 0.16 0.16 0.08 0.16 0.16 0.16 0.08 0.16 0.16 0.08 0.16 0.16 0.16 0.08 0.16 0.16 0.16 0.08 0.34 0.18 0.18 0.26 0.26 0.26 0.19 0.19 0.19 0.19 0.16 0.16 0.16 0.14 0.14 0.14 0.14 0.12 0.12 0.12 0.12 0.10 0.10 0.10 Standard Product EEEFK0J471GP EEEFK0J102GP EEEFK0J152GP EEEFK1A331GP EEEFK1A471GP EEEFK1A681GP EEEFK1A102GP EEEFK1C331GP EEEFK1C471GP EEEFK1C681GP EEEFK1E151GP EEEFK1E221GP EEEFK1E331GP EEEFK1E471GP EEEFK1V101GP EEEFK1V151GP EEEFK1V221GP EEEFK1V331GP EEEFK1H101GP EEEFK1H151GP EEEFK1H221GP Vibration-proof product EEEFK0J471GV EEEFK0J102GV EEEFK0J152GV EEEFK1A331GV EEEFK1A471GV EEEFK1A681GV EEEFK1A102GV EEEFK1C331GV EEEFK1C471GV EEEFK1C681GV EEEFK1E151GV EEEFK1E221GV EEEFK1E331GV EEEFK1E471GV EEEFK1V101GV EEEFK1V151GV EEEFK1V221GV EEEFK1V331GV EEEFK1H101GV EEEFK1H151GV EEEFK1H221GV Reflow Rated voltage (V) (mm) Size code Case size Min. Packaging Q'ty (pcs) Taping (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 *1: Ripple current (100 kHz / +105 ℃） *2: Impedance (100 kHz / +20 ℃) *3: tan δ (120 Hz / +20 ℃) ・ Please refer to the page of "Reflow Profile" and "The Taping Dimensions". Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06-Dec-19 Guidelines and precautions regarding the technical information and use of our products described in this online catalog. ■ If you want to use our products described in this online catalog for applications requiring special qualities or reliability, or for applications where the failure or malfunction of the products may directly jeopardize human life or potentially cause personal injury (e.g. aircraft and aerospace equipment, traffic and transportation equipment, combustion equipment, medical equipment, accident prevention, anti-crime equipment, and/or safety equipment), it is necessary to verify whether the specifications of our products fit to such applications. Please ensure that you will ask and check with our inquiry desk as to whether the specifications of our products fit to such applications use before you use our products. ■ The quality and performance of our products as described in this online catalog only apply to our products when used in isolation. Therefore, please ensure you evaluate and verify our products under the specific circumstances in which our products are assembled in your own products and in which our products will actually be used. ■ If you use our products in equipment that requires a high degree of reliability, regardless of the application, it is recommended that you set up protection circuits and redundancy circuits in order to ensure safety of your equipment. ■ The products and product specifications described in this online catalog are subject to change for improvement without prior notice. Therefore, please be sure to request and confirm the latest product specifications which explain the specifications of our products in detail, before you finalize the design of your applications, purchase, or use our products. ■ The technical information in this online catalog provides examples of our products' typical operations and application circuits. We do not guarantee the non-infringement of third party's intellectual property rights and we do not grant any license, right, or interest in our intellectual property. ■ If any of our products, product specifications and/or technical information in this online catalog is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially with regard to security and export control, shall be observed. ■ The switchover date for compliance with the RoHS Directive/REACH Regulations varies depending on the part number or series of our products. ■ When you use the inventory of our products for which it is unclear whether those products are compliant with the RoHS Directive/REACH Regulation, please select "Sales Inquiry" in the website inquiry form and contact us. We do not take any responsibility for the use of our products outside the scope of the specifications, descriptions, guidelines and precautions described in this online catalog. 16-Apr-21 Notices / Items to be observed Notices ■ Applicable laws and regulations ・This product complies with the RoHS Directive (Restriction of the use of certain hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU and（EU)2015/863)). ・ No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. We do not use PBBs or PBDEs as brominated flame retardants. ・ Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this product. ・ These products are not dangerous goods on the transportation as identified by UN(United Nations) numbers or UN classification. ■ Limited applications ・ This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home appliances, computers and other office equipment, optical equipment, measuring equipment. ・ An advanced specification must be signed individually for high-reliability use that might threaten human life or property due to a malfunction of the capacitor. ■ Intellectual property rights and licenses ・ The technical information in this specification provides examples of our products' typical operations and application circuits. We do not guarantee the non-infringement of third party's intellectual property rights and we do not grant any license, right, or interest in our intellectual property. Items to be observed ■ For specification ・ This specification guarantees the quality and performance of the product as individual components. The durability differs depending on the environment and the conditions of usage. Before use, check and evaluate their compatibility with actual conditions when installed in the products. When safety requirements cannot be satisfied in your technical examination, inform us immediately. ・ Do not use the products beyond the specifications described in this document. ■ Upon application to products where safety is regarded as important Install the following systems for a fail-safe design to ensure safety if these products are to be used in equipment where a defect in these products may cause the loss of human life or other signification damage, such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime prevention equipment. (1) The system is equipped with a protection circuit and protection device. (2) The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault. ■ Conditions of use ・ Before using the products, carefully check the effects on their quality and performance, and determined whether or not they 　can be used. These products are designed and manufactured for general-purpose and standard use in general electronic equipment. These products are not intended for use in the following special conditions. (1) In liquid, such as Water, Oil, Chemicals, or Organic solvent. (2) In direct sunlight, outdoors, or in dust. (3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx. (4) In an environment where strong static electricity or electromagnetic waves exist. (5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these products. (6) Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin and other material. (7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues) (8) Using in the atmosphere where strays acid or alkaline. (9) Using in the atmosphere where there are excessive vibration and shock. (10) Using in the atmosphere where there are low pressure or decompression. ・ Please arrange circuit design for preventing impulse or transitional voltage. 　Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage, instantaneous high 　voltage, high pulse voltage etc. ・ Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and affects performance, characteristics, and functions of customer system. 16-Apr-21 Aluminum Electrolytic Capacitors (SMD Type) 　　Application guidelines (SMD Type) 1. Circuit design 1.1 Operating temperature and frequency Electrical characteristics of the capacitor are likely to change due to variation in temperature and/or frequency. Circuit designers should take these changes into consideration. (1) Effects of operating temperature on electrical parameters At higher temperatures : Leakage current increases At lower temperatures : Hybrid type has smaller capacitance and larger tan δ. Other aluminum electrolytic capacitors have smaller capacitance, larger tan δ, and larger impedance as well as equivalent series resistance (ESR). (2) Effects of frequency on electrical parameters At higher frequency capacitance and impedance decrease while tanδ increases. At lower frequency, heat generated by ripple current will rise due to an increase in equivalent series resistance (ESR). 1.2 Operating temperature and life expectancy (1) Expected life is affected by operating temperature. Generally, each 10 °C reduction in temperature will double the expected life. Use capacitors at the lowest possible temperature below the upper category temperature. (2) If operating temperatures exceed the upper category limit, rapid deterioration of electrical parameter will occur and irreversible damage will result. Measure not only the ambient temperature but also the surface temperature of the capacitor’s case top, which has effects of ripple current and radiated heat from power transistors, IC's, and/or resistors. Avoid placing components, which could conduct heat to the capacitor from the back side of the circuit board. (3) The formula for calculating expected life is as follows ; T1-(T2+⊿T) L2 = L1×2 10 where T1 ≧ T2 L1 : Guaranteed life (h) at temperature, T1 (℃) L2 : Expected life (h) at temperature, T2 (℃) T1 : Upper category temperature (℃) *Hybrid type : + temperature rise due to rated ripple current (℃) T2 : Capacitor's ambient temperature (℃) ⊿T : Temperature rise due to ripple current (°C) (4) Using the capacitor beyond the rated lifetime will result in short circuit, electrolyte leak, vent open, and large deterioration of characteristics. The lifetime cannot exceed 15 years due to aging of sealing rubber. (5) If the capacitor is used in a high temperature condition for a long time, micro cracks may appear on the surface of sealing rubber, and/or capacitor case exterior may become brownish in color, but the product reliability will not be influenced. 1.3 Load conditions to avoid The following load conditions will cause rapid deterioration of capacitor’s electrical characteristics. In addition, instantaneous heating and gas generation within the capacitor may cause an operation of pressure relief vent, and that results in electrolyte leaks, explosion and/or fire ignition. The leaked electrolyte is combustible and electrically conductive. (1) Reverse voltage DC capacitors have polarity. Therefore, do not apply the reverse voltage. Find the correct polarity before insertion. (2) Charge / Discharge applications General purpose capacitors are not suitable for use in repeating charge/discharge applications. For such applications, consult a sales representative with actual application condition. Rush current must not exceed 100 A. (3) ON-OFF circuit When using capacitors in circuit where ON-OFF switching is repeated more than 10,000 times a day, consult a sales representative with actual application condition for an appropriate choice of capacitors. (4) Over voltage Do not apply a voltage exceeding the rated voltage. The rated surge voltage can be applied only for a short time. 　　 Make sure that a sum of the DC voltage and the superimposed AC ripple voltage does not exceed the rated voltage. 01-Nov-22 Aluminum Electrolytic Capacitors (SMD Type) (5) Ripple current Do not apply ripple currents exceeding the rated value. Make sure that rated ripple currents superimposed on low DC bias voltages do not cause reverse voltage conditions. Even if the current is below the rated ripple current, using the capacitor for longer than the rated lifetime will cause ESR increase and internal generation of heat, which may eventually lead to vent open, bulging of case/rubber, electrolyte leak, short circuit, explosion, or ignition in the worst case. 1.4 Connections in series or parallel (1) Capacitors connected in parallel Because the impedance of the capacitor and PCB’s wiring are very close, various impedance values may cause unbalanced ripple current loads among parallel capacitors. Combine the same part number and wire them carefully to minimize the potential risk of an excessive ripple current concentrating to one capacitor of the smallest impedance. (2) Capacitors connected in series Voltage being applied to each capacitor must be smaller than the rated voltage. Unbalanced voltages to the series capacitors may exceed the rated voltage. Voltage-divider resistors considering leakage currents could prevent the over-voltage to the series capacitors. Conductive polymer hybrid aluminum electrolytic capacitors are not allowed to be connected in series. 1.5 Capacitor mounting considerations (1) For double sided circuit boards, avoid wiring patterns passing between the mounted capacitor and the circuit board. When a radial lead type capacitor is dipped into a solder bath, an excess solder may deposit under the capacitor by capillary action, causing short circuit between anode and cathode terminals. Also, lead holes must be placed with special care for radial lead type capacitors because laminate on capacitor’s surface may become damaged during flow process. (2) The pitch between circuit board holes should match the lead wire pitch of the radial lead type capacitors within the specified tolerances. Unmatched pitch may cause an excessive stress on lead wires during the insertion process and result in short/open circuit, increased leakage current, or electrolyte leak. (3) Clearance for case mounted pressure relief Capacitors with case mounted pressure relief require sufficient clearance to allow for proper pressure relief operation. The minimum clearance are dependent on capacitor diameters as follows. (Ø 10 mm to Ø 16 mm: 2 mm minimum, Ø 18 mm: 3 mm minimum) (4) Wiring near the pressure relief Avoid locating high voltage or high current wiring or circuit board paths above the pressure relief. Flammable, high temperature gas that exceeds 100 ℃ may be released which could dissolve the wire insulation and ignite. (5) Circuit board patterns under the capacitor Avoid circuit board runs under the capacitor, as an electrical short can occur due to an electrolyte leakage. (6) Resonant vibration after circuit board’s production may make a heavy load on the capacitor and cause rapid change in characteristics and/or capacitor’s break. 1.6 Electrical isolation Electrically isolate the capacitor’s case from cathode terminals, as well as circuit patterns. 1.7 Capacitor coating The laminate coating is intended for marking and identification purposes and is not meant to electrically insulate the capacitor. Its color may become brownish in a high-temperature condition, but the marking appearance and electrical characteristics will not be influenced. 2. Capacitor handling techniques 2.1 Considerations before using (1) Capacitors have a finite life. Do not reuse or recycle capacitors from used equipment. (2) Transient recovery voltage may be generated in the capacitor due to dielectric absorption. If required, this voltage can be discharged with a resistor with a value of about 1 kΩ. (3) Capacitors stored for a long period of time may exhibit an increase in leakage current. This can be corrected by gradually applying rated voltage in series with a resistor of approximately 1 kΩ. (4) If capacitors are dropped, they can be damaged mechanically or electrically. Avoid using dropped capacitors. (5) Dented or crushed capacitors should not be used. The seal integrity can be damaged and loss of electrolyte/ shortened life can result. 01-Nov-22 Aluminum Electrolytic Capacitors (SMD Type) 2.2 Capacitor insertion (1) Verify the correct capacitance and rated voltage of the capacitor. (2) Verify the correct polarity of the capacitor before insertion. (3) Verify the correct terminal dimension and land pattern size for surface mount type, or holes’ pitch for radial lead type before mount to avoid short circuit, stress on the terminals, and/or lack of terminal strength. (4) Excessive mounting pressure can cause high leakage current, short circuit, or disconnection. (5) When using a mounter for radial lead type, avoid cutter wear and acute angle of lead-bending with respect to circuit board. That may create excessive stress and pull the lead to damage the capacitor. 2.3 Reflow soldering (for surface mount type) (1) Surface-mount type capacitor are exclusively for reflow soldering. When reflow solder is used an ambient heat condition system such as the simultaneous use of infrared and hot-air is recommended. (2) Observe proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits. If the peak temperature is high or if the heating time is long, it may cause deterioration of the electrical characteristics and life characteristics. Recommended soldering condition is a guideline for ensuring the basic characteristics of the components, but not for the stable soldering conditions. Conditions for proper soldering should be set up according to individual onditions. 　・ The Temperature on Capacitor top shall be measured by using thermal couple that is fixed firmly by epoxy glue. (3) In case of use in 2 times reflow, 2nd reflow must be done when the capacitor’s temperature return back to normal level. (4) In our recommended reflow condition , the case discoloration and the case swelling might be slightly generated. But please acknowledge that these two phenomena do not influence the reliability of the product. (5) The crack on top marking might be occurred by reflow heat stress. 　But please acknowledge that it does not influence the reliability of the product. (6) VPS (Vapor Phase Soldering) reflow can cause significant characteristics change and/ or mounting failure due to deformation by acute temperature rise. VPS is acceptable provided that the process does not exceed recommended reflow profile and temperature rise is less than 3 ℃/sec. Please contact Panasonic for detailed conditions. (7) The vibration-proof capacitors of size ø6.3 has support terminals extending from the bottom side to the lead edge. Then, make sure to find appropriate soldering conditions to form fillet on the support terminals if required for appearance inspection. However, even if sufficient solder fillets are not observed, the reliability of vibration-proof will not be lowered because the support terminals on the bottom side enhance the solder joint to PCB. 2.4 Flow soldering (for radial lead type) (1) Radial lead type capacitors cannot apply to reflow soldering. (2) Do not immerse the capacitor body into the solder bath as excessive internal pressure could result. (3) Apply proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits. (4) Do not allow other parts or components to touch the capacitor during soldering. 2.5 Manual soldering (1) Apply soldering conditions (temperature and time) based on the specification, or do not exceed temperature of 350 ℃ for 3 seconds. (2) If a soldered capacitor must be removed and reinserted, avoid excessive stress on the capacitor leads. (3) Avoid physical contacts between the tip of the soldering iron and capacitors to prevent capacitor failure. (4) When bending lead wires of radial type capacitors to match the hole pitch on PCB, avoid applying excessive stress to the capacitor body. 2.6 Capacitor handling after soldering (1) Avoid moving the capacitor after soldering to prevent excessive stress on the lead wires where they enter the seal. The capacitor may break from element portion due to a torque at outer rim, causing a large stress to terminals. (2) Do not use the capacitor as a handle when moving the circuit board assembly. The total weight of the board would apply to element portion through terminals, and the capacitor may break. (3) Avoid striking the capacitor after assembly to prevent failure due to excessive shock. The capacitor may break due to excessive shock or load above specified range. 01-Nov-22 Aluminum Electrolytic Capacitors (SMD Type) 2.7 Circuit board cleaning (1) Circuit boards can be immersed or ultrasonically cleaned using suitable cleaning solvents for up to 5 minutes and up to 60 °C maximum temperatures. The boards should be thoroughly rinsed and dried. The use of ozone depleting cleaning agents is not recommended for the purpose of protecting our environment. 【Target solvent】 Pine Alpha ST-100S, Aqua Cleaner 210SEP, Clean-thru 750H / 750L / 710M, Sunelec B-12, Sunelec B-12, Cold Cleaner P3-375, Techno Cleaner 219, DK Be-clear CW-5790, Telpene Cleaner EC-7R, Technocare FRW-17 / FRW-1 / FRV-1 (2) Avoid using the following solvent groups unless specifically allowed in the specification ; (a) Halogenated based solvents : may permeate the seal and cause internal corrosion. Especially, 1-1-1 trichloroethane must not be used on any aluminum electrolytic capacitors. (b) Alkaline based solvents ： may dissolve and react to the aluminum case. (c) Petroleum based solvents ： may deteriorate the sealing rubber. (d) Xylene ： may deteriorate the sealing rubber. (e) Acetone ： may erase the markings on the capacitor top. (3) A thorough drying after cleaning is required to remove residual cleaning solvents that may be trapped between the capacitor and the circuit board. Avoid drying temperatures, which exceed the upper category temperature of the capacitor. (4) Monitor the contamination levels of the cleaning solvents during use in terms of electrical conductivity, pH, specific gravity, and water content. Inside the capacitor may corrode with high density of chlorine. Control the flux density in the cleaning agent to be less than 2 mass%. (5) Depending on the cleaning method, the marking on a capacitor may be erased or blurred. ※ Please consult us if you are not certain about acceptable cleaning solvents or cleaning methods. 2.8 Mounting adhesives and coating agents When using mounting adhesives or coating agents to control humidity, avoid using materials containing halogenated solvents. Also, avoid the use of chloroprene based polymers. Cure or dry out the coating agents thoroughly, and do not leave any solvents. Make sure to dry out cleaning agents completely immediately after washing the circuit board if the capacitors are mounted afterward, so that the solvents are not left under the capacitor body. Also, leave more than 1/3 of the sealing portion open, and do not cover that portion with any adhesives or coating. 2.9 Potting and molding Potting and molding processes cannot be recommended. They have potential risks to change the capacitor’s performance and reliability due to injection pressure, diffused material into the capacitor, as well as heat accumulation by covered resin. Also, evaporated electrolyte may remain inside the resin, then turn to liquid, and possibly short circuit PCB patterns. 2.10 Fumigation In exporting electronic appliances with aluminum electrolytic capacitors, in some cases fumigation treatment using such halogen compound as methyl bromide is conducted for wooden boxes. If such boxes are not dried well, the halogen left in the box is dispersed while transported and enters in the capacitors inside. This possibly causes electrical corrosion of the capacitors. Therefore, after performing fumigation and drying make sure that no halogen is left. Don’t perform fumigation treatment to the whole electronic appliances packed in a box. 2.11 Flux If you use a halogen type (Chlorine type, Bromine type, etc.) high-activity flux, please use it after confirmation in advance, as it may have an impact on performance and reliability of this product due to the residue of the flux. 3. Precautions for using capacitors 3.1 Environmental conditions Capacitors should not be stored or used in the following environments. (1) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor. (2) Direct contact with water, salt water, or oil. (3) High humidity conditions where water could condense on the capacitor. (4) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, chlorine compound, bromine, bromine compound or ammonia. (5) Exposure to ozone, radiation, or ultraviolet rays. (6) Vibration and shock conditions exceeding specified requirements. Even within the specified requirements, a large vibration acceleration may be applied due to resonance, so be sure to evaluate and confirm with the actual product. 01-Nov-22 Aluminum Electrolytic Capacitors (SMD Type) 3.2 Electrical precautions (1) Avoid touching the terminals of a capacitor as a possible electric shock could result. The exposed aluminum case is not insulated and could also cause electric shock if touched. (2) Avoid short circuiting the capacitor terminals with conductive materials such as acids or alkaline solutions. (3) Electrical characteristics may largely change if a silicon material with low molecular-weight siloxane is used near the capacitor. 4. Emergency procedures (1) If the pressure relief of the capacitor operates, immediately turn off the equipment and disconnect from the power source. This will minimize an additional damage caused by the vaporizing electrolyte. (2) Avoid contact with the escaping electrolyte gas, which can exceed 100 ℃ temperatures. If electrolyte or gas enters the eye, immediately flush the eye with large amounts of water. If electrolyte or gas is ingested by mouth, gargle with water. If electrolyte contacts the skin, wash with soap and water. 5. Long term storage (1)　Leakage current of a capacitor tends to increase after a long-term storage due to dielectric dissolution, and very high current may flow at the first voltage load. However, applying voltage will form the dielectric, and the leakage current will decrease. Expiration date is 42 months from the outgoing inspection date for part numbers listed below, and it is 12 month for part numbers not listed below. Series S (Only high temperature reflow) HA (Only high temperature reflow) HB (Only high temperature reflow and 5.4 mm height) HC, HD, FCA, FC, FKA, FK, FKS, FN, FP, FT, FH, TG, TK,TP, TC, TCU, TQ Expiration date 42 months from outgoing inspection date Storage condition is to keep in room temperature (5 ℃ to 35 ℃) and humidity (45 % to 85 %) with no direct sunshine. （2）Environmental conditions Do not store under condition outside the area described in the specification, and also under conditions listed below. (a) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor. (b) Direct contact with water, salt water, or oil. (c) High humidity conditions where water could condense on the capacitor. (d) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, chlorine compound, bromine, bromine compound or ammonia. (e) Exposure to ozone, radiation, or ultraviolet rays. (f) Vibration and shock conditions exceeding specified requirements. 6. Capacitor disposal When disposing capacitors, use one of the following methods. (1) Incinerate after crushing the capacitor or puncturing the can wall (to prevent explosion due to internal pressure rise). (2) Dispose as solid waste. NOTE : Local laws may have specific disposal requirements which must be followed. The precautions in using aluminum electrolytic capacitors follow the "Safety application guide for the use in fixedaluminum electrolytic capacitors for electronic equipment", RCR-2367D issued by JEITA in October 2017. Please refer to the above application guide for details. ■ AEC-Q200　compliant The products are tested based on all or part of the test conditions and methods defined in AEC-Q200. Please consult with Panasonic for the details of the product specification and specific evaluation test results, etc., and please review and approve Panasonic's product specification before ordering. 01-Nov-22