EEF-UE0G221CX

2018 Products Catalog Conductive Polymer Aluminum Electrolytic Capacitors 2018.4 http://industrial.panasonic.com/ww/products/capacitors/polymer-capacitors/sp-cap ——— Notices ——— ■ Applicable Laws and Regulations ● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU). ● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. ● We do not use PBBs or PBDEs as brominated flame retardants. ● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this product. ■ Limited applications ● This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home appliances, computers and other office equipment, optical equipment, measuring equipment. ● High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm to a human life or property ] more. When use is considered by the use, the delivery specifications which suited the use separately need to be exchanged. ——— Items to be observed ——— ● This specification guarantees the quality and performance of the product as individual components. Before use, check and evaluate their compatibility with installed in your products. ● Do not use the products beyond the specifications described in this document. ■ For specifications ● Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment where a defect in these products may cause the loss of human life or other signification damage, such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime prevention equipment. · The system is equipped with a protection circuit and protection device. · The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault. ■ Conditions of use ● Before using the products, carefully check the effects on their quality and performance, and determined whether or not they can be used. These products are designed and manufactured for general-purpose and standard use in general electronic equipment. These products are not intended for use in the following special conditions. (1) In liquid, such as Water, Oil, Chemicals, or Organic solvent. (2) In direct sunlight, outdoors, or in dust. (3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx. (4) In an environment where strong static electricity or electromagnetic waves exist. (5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these products. (6) Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin and other material. (7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues) (8) Using in the atmosphere which strays Acid or alkaline. (9) Using in the atmosphere which there are excessive vibration and shock. ● Please arrange circuit design for preventing impulse or transitional voltage. Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage, instantaneous high voltage, high pulse voltage etc. ● Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and affects performance, characteristics, and functions of customer system. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Mar. 2017 Conductive Polymer Aluminum Electrolytic Capacitors Application Guidelines (SP-Cap) 1. Circuit design 1.1 Prohibited circuits for use Do (1) (2) (3) (4) (5) not use the SP-Cap with the following circuit. Time-constant circuit Coupling circuits 2 or more SP-Cap connected serially Circuit which are greatly affected by leakage current High-impedance voltage retention circuits 1.2 Voltage and polarity The application of over- voltage and reverse voltage described below can cause increases in leakage current and short circuits. Applied voltage, refers to the voltage value including the peak value of the transitional Instantaneous voltage and the peak value of ripple voltage, not just steady line voltage. Design your circuit so than the peak voltage does not exceed the stipulated voltage. [Over-Voltage] Do not apply over-voltage in excess of the rated voltage. Do not apply voltage, which exceeds the full rated voltage when the SP-Cap receive impulse voltage, instantaneous high voltage, high pulse voltage etc. [Reverse-Voltage] Do not apply reverse-voltage 1.3 Ripple current Use the SP-Cap within the stipulated permitted ripple current. When excessive ripple current is applied to the SP-Cap, if causes increases in leakage current and short circuits due to self-heating. Even when using the SP-Cap under the permissible ripple current, reverse voltage may occur if the DC bias voltage is low. 1.4 Leakage current There is a risk of leakage current characteristics increasing even if the following use environments are within the stipulated range. However, even if the leakage current increases, the SP-Cap self-repairing function will reduce the leakage current in most cases when a voltage is applied. (1) After re-flow (2) Shelf conditions such as high temperature with no load, high temperature high humidity with no load and sudden temperature changes. 1.5 Temperature (1) Use at or under the rated (guaranteed) temperature. Operation at temperatures exceeding specifications causes large changes in the SP-Cap electrical properties, and deterioration than can potentially lead to failure. When calculating the operating temperature of the SP-Cap, be sure to include not only the ambient temperature and internal temperature of the unit, but also radiation from heat generating elements inside the unit (power transistors, resistors, etc.), and self-heating due to ripple current. (2) Specified ESR is a value at the time of shipping from factory. ESR may change upon use conditions. 1.6 Failure rate The majority of failure modes are short circuits or increases in leakage current. The main factors of failure are mechanical stress, heat stress and electric stress due to re-flow and heat from the use temperature environment. Even within the stipulated limits, it is possible to lower the failure rate by reducing use conditions such as temperature and voltage. Please be sure to have ample margin in your design. [Expected Failure Rate] (1) Date based on our reliability tests: 8.2 Fit or less (Based on applied rated voltage at 105 °C) (2) Market failure rate: 0.13 Fit or less (Based on c=0, Reliability standard : 60 %) 1.7 Mounting area consideration Isolate the surface of PCB under the mounted SP-Cap. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Jan. 2018 Conductive Polymer Aluminum Electrolytic Capacitors 2. Mounting 2.1 When mounting (1) (2) (3) (4) Check the SP-Cap ratings (capacitance and voltage) before mounting. Check the SP-Cap polarity before mounting. Check the land size for the SP-Cap before mounting. When using a mounter, if the pressure for mounting is too high, then the current leak may increase, shortcircuiting may occur, or the SP-Cap may break down or come off. 2.2 Soldering (1) Reflow soldering Be performed by one of following methods. (a) Ambient heat conduction reflow (IR / Hot-air) Please refer to the page of “Mounting Specifications”. (b) Vapor phase reflow (but only allowable for CX, CT, SX, ST, GX, LX, LT and HX series). Please contact Panasonic for details of allowable vapor phase reflow condition. (2) Wave soldering and dip soldering Please remind SP-Cap is NOT compatible. (3) Hand soldering Excessive force stress to the SP-Cap should be avoided Conditions : Tip temperature of soldering iron : 350 °C max. Exposure time : 10 s max. ✽ Once removed from the printed circuit board for any reason, please do not use the SP-Cap again. 2.3 Land size Refer to the land size of “Mounting specifications” for appropriate design dimensions. Circuit board design requires examination of the most suitable dimensions taking conditions such as circuit board, parts and reflow into consideration. 2.4 Mechanical stress Do not apply excessive force to the SP-Cap this can damage the electrodes and badly affect the SP-Cap mount ability. It can also cause the increase of leakage current, separation of the lead wire and element, and damage to the SP-Cap body, all of which can badly affect the electrical performance of the SP-Cap. 2.5 Circuit board cleaning SP-Cap should be cleaned after soldering in accordance with the following conditions. Temperature : Less than 60 °C Time : Within 5min Be sure to sufficiently wash and dry (20 min at 100 °C) the board afterward. [Recommended Cleaning Solvents] Pine Alpha ST-100S, Clean-thru 750H / 750L / 710M, Aqua Cleaner 210SEP, Sunelec B-12 DK Beclear CW-5790, Techno Cleaner 219, Cold Cleaner P3-375, Telpene Cleaner EC-7R Technocare FRW-17 / FRW-1 / FRV-1, AXREL 32, IPA (Isopropyl alcohol) (1) Consult our factory when performing processes with cleaning solvents other than those listed above or deionized water. (2) The use of ozone depleting cleaning agents are not recommended in the interest of protecting the environment. (3) In the case of using ultrasonic cleaning, the terminals may be broken. Therefore, please test before using in mass production. 3. Usage environment of equipment Avoid using equipment to which SP-Cap are fi ted in the following environments. (1) In liquid, such as Water, Oil, Chemicals, or Organic solvent. (2) In direct sunlight, outdoors, or in dust. (3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2. (4) In an environment where strong static electricity or electromagnetic waves exist. (5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these SP-Cap. (6) Sealing or coating of these SP-Cap or a printed circuit board on which these SP-Cap are mounted, with resin and other material. (7) Acid or alkaline environments. (8) Environment subject to excessive vibration and shock. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Jan. 2018 Conductive Polymer Aluminum Electrolytic Capacitors 4. Storage SP-Cap should be stored in a moisture proof environment. Storage conditions before and after opening the moisture proof packaging as follows. (If these conditions are exceeded, the package may absorb moisture and there is a risk of damage to the exterior due to heat stress during mounting.) [Environment of Storage] Temperature: 5 °C to 30 °C without direct sunlight Humidity : Less than 70 % Maximum storage term before opening the package (2 years after manufactured) Maximum storage condition after opening the package (7 days after opening) SP-Cap should be all used within the storage term after opening the package. 5. Transportation Take sufficient care during handling because excessive vibration, or shock can cause the reliability of the SP-Cap to decrease. 6. Emergency procedures If the SP-Cap is overheated, the resin case may emit smoke. If this occurs, immediately switch off the unit’s main power supply to stop operation. Keep your face and hands away from the SP-Cap the temperature may be high enough to cause the SP-Cap to ignite and burn. 7. Discarding Since SP-Cap are composed of various metals and resins, treat them as industrial waste when arranging for their disposal. The precautions for the use of functional polymer aluminum electrolytic capacitors follow the “Precautionary guidelines for the use of fixed aluminum electrolytic capacitors for electronic equipment”, RCR- 2367B issued by EIAJ in March 2002. Please refer to the above guidelines for details. ◇ Intellectual property right We, Panasonic Group are providing the product and service that customers can use without anxiety, and are working positively on the protection of our products under intellectual property rights. Representative patents relating to SP-Cap are as follows : US Patent No. 7136276 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Jan. 2018 Conductive Polymer Aluminum Electrolytic Capacitors Line up CX EEFCX---- CT EEFCF---- CS EEFCS---- SX EEFSX---- GX EEFGX---- LX EEFLX---- ST EEFST---- LT EEFLT---- SS EEFSS---- LS EEFLS---- SR EEFSR---- LR EEFLR---- CY ECGCY---- Guaranteed at 85℃ , SY ECGSY---- Height 3.0 mm max. , HX EEFHX---- Super low ESR/High ripple current Conductive Polymer Aluminum Electrolytic Capacitors Diagram 2-terminals Standard Products 3-terminals Low ESR Products Low ESR/Low ESL Products✽ CX Series 7.3×4.3×1.9 mm GX Series 7.3×4.3×1.9 mm GX-L Series 7.3×4.3×1.9 mm 2 V.DC/560 µF to 35 V.DC/22 µF ESR : 12 mΩ to 40 mΩ 2 V.DC/560 µF to 2.5 V.DC/470 µF ESR : 3 mΩ 2 V.DC/560 µF to 2.5 V.DC/470 µF ESR : 3 mΩ Low profile Super Low ESR Super Low ESR CT Series 7.3×4.3×1.4 mm SX Series 7.3×4.3×1.9 mm LX Series 7.3×4.3×1.9 mm 4 V.DC/180 µF to 35 V.DC/15 µF ESR : 15 mΩ/40 mΩ 2 V.DC/560 µF to 6.3 V.DC/180 µF ESR : 4.5 mΩ to 9 mΩ 2 V.DC/560 µF to 2.5 V.DC/470 µF ESR : 4.5 mΩ/6 mΩ Low profile Low profile CS Series 7.3×4.3×1.1 mm 4 V.DC/120 µF to 35 V.DC/10 µF ESR : 15 mΩ/40 mΩ ST Series 7.3×4.3×1.4 mm LT Series 7.3×4.3×1.4 mm 2 V.DC/330 µF to 2.5 V.DC/270 µF ESR : 6 mΩ 2 V.DC/330 µF to 2.5 V.DC/270 µF ESR : 6 mΩ SS Series 7.3×4.3×1.1 mm LS Series 7.3×4.3×1.1 mm 2 V.DC/220 µF to 2.5 V.DC/180 µF ESR : 6 mΩ 2 V.DC/220 µF to 2.5 V.DC/180 µF ESR : 6 mΩ SR Series 7.3×4.3×1.0 mm (max.) LR Series 7.3×4.3×1.0 mm (max.) 2 V.DC/220 µF to 6.3 V.DC/68 µF ESR : 4.5 mΩ to 9 mΩ 2 V.DC/220 µF to 6.3 V.DC/68 µF ESR : 4.5 mΩ to 9 mΩ Guaranteed at 85 °C CY/SY Series 7.3×4.3×2.8 mm 4 V.DC/470 µF to 6.3 V.DC/330 µF ESR : 9 mΩ/15 mΩ Guaranteed at 125 °C HX Series 7.3×4.3×1.9 mm 2 V.DC/560 µF to 25 V.DC/33 µF ESR : 4.5 mΩ to 40 mΩ ✽ : ESL : 0.5nH (Typ.) Old Series Standard Products CD Series 7.3×4.3×1.8 mm 2 V.DC 220 µF to 16 V.DC 8.2 µF ESR : 15 mΩ to 110 mΩ Low Profile FD Series 7.3×4.3×1.1 mm 2 V.DC 68 µF to 12.5 V.DC 15 µF ESR : 28 mΩ to 40 mΩ Low ESR Products SL Series 7.3×4.3×1.9 mm 2 V.DC 220 µF to 6.3 V.DC 56 µF ESR : 9 mΩ UD Series 7.3×4.3×2.8 mm 2 V.DC 470 µF to 8 V.DC 100 µF ESR : 9 mΩ to 18 mΩ UE Series 7.3×4.3×4.2 mm 2 V.DC 560 µF to 8 V.DC 150 µF ESR : 7 mΩ to 15 mΩ Miniaturization Products MC Series 6.3×3.2×1.9 mm 2 V.DC 120 µF to 6.3 V.DC 47 µF ESR : 12 mΩ to 18 mΩ Please contact us when old series is necessary. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Jul. 2017 Conductive Polymer Aluminum Electrolytic Capacitors Mounting Specifications ● Recommendable reflow soldering Temperature on the surface of capacitor (°C) Soldering temperature and Soldering time Peak temperature 260 °C 10 s max. Temperature Time > 255 °C > 230 °C 130 s max. > 217 °C 150 s max. Soldering temperature 250 30 s max. 200 150 Soldering time 150 to 200 °C 180 s max. 100 Sp-Cap recommended profile condition of the IPC/J-STD-020D standard 50 Time (s) Reflow cycle : 3 max. EX.) Peak temperature 10 s max. Peak temperature Time in 230 °C or more 260 °C, 10 s max. 40 s max. 250 °C, 10 s max. 60 s max. 250 200 150 Time in 230 °C or more 150 to 200 °C 120 s max. 100 50 Time (s) 270 260 250 240 230 0 Reflow cycle : 2 max. ● Typical Peak temperature (°C) Temperature on the surface of capacitor (°C) 10 20 30 40 50 60 70 Time in 230 °C or more (s) land pattern For standard terminal (2-terminals) a c b Unit : mm Capacitor Series a b c Standard (Except MC) 8.8 4.0 2.8 (MC) 7.2 2.6 2.2 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 03 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors ● Typical ● VIA land pattern For Low ESL terminal (3-terminals) (LR, LS, LT, LX, GX-L series) For Low ESL terminal (3-terminals) (LR, LS, LT, LX, GX-L series) Unit : mm Unit : mm VIA(+)10-00.4 8.8 4.0 2.7 VIA(–)10-00.4 – 1.3 0.5 – + – – 1.15 1.9 2.8 5.1 + Capacitor 0.9 0.9 Capacitor 0.9 0.9 0.9 0.5 0.3 0.3 Packaging Specifications ● Reel ● Embossed Dimensions Taping 0D0 (Feeding hole) P0 P2 Tape running direction b E t F – A W E 0C a 0A 0B a + 0D R:1.0 P1 b Chip pocket B b-b Cross section a-a Cross section Unit : mm W A B W F E P1 Standard (MC series) Standard (MC series) 7.6±0.2 6.3±0.3 4.5±0.2 3.6±0.3 12.0±0.3 5.5±0.1 1.75±0.10 8.0±0.1 t Unit : mm 0A 0B 0330 330 80 Reel 0C 0D E 13±0.5 21±0.8 2±0.5 W t 14 3 P2 P0 0D0 2.0±0.1 4.0±0.1 1.5+0.1 0 Upper row : Product height (mm) / Lower berth : t to 1.1 1.4 to 1.9 2.8 4.2 (MC series) 1.5±0.2 2.4±0.2 3.5±0.2 4.3±0.2 2.8±0.3 a Packaging Box Dimensions c Unit : mm Reel b 0330 a b c 400 max. 400 max. 135 max. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 03 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : CS, CT, CX Features ● High voltage (35 V.DC max.) profile (Height 1.0 mm max.) ● High ripple current (5600 mAr.m.s. max.) ● RoHS compliance, Halogen free ● Low Specifications Series CS CT Category temp. range CX –55 °C to +105 °C Rated voltage range 4 V.DC to 35 V.DC Nominal cap.range 10 μF to 120 μF 2 V.DC to 35 V.DC 15 μF to 180 μF 15 μF to 560 μF Capacitance tolerance ±20 % (120 Hz / + 20 °C) DC leakage current I < 0.1 CV (μA) [2 V.DC to 6.3 V.DC, 2 minutes], I < 0.3 CV (μA) [10 V.DC to 35 V.DC, 2 minutes] Dissipation factor (tan d) < 0.06 (120 Hz / + 20 °C) Surge voltage (V.DC) Rated voltage × 1.25 [2 V.DC to 16 V.DC], × 1.15 [20 V.DC to 35 V.DC] (15 °C to 35 °C) +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance < 2 times of the initial limit 2 V.DC to 6.3 V DC : < 3 times of the initial limit DC leakage current 10 V.DC to 35 V.DC : Within the initial limit +60 °C, 90 %, 500 h, No-applied voltage tan d Capacitance change of initial measurd value Damp heat (Steady state) 2 V.DC to 2.5 V.DC 4 V.DC, 10 V.DC to 35 V.DC 6.3 V.DC +70 %, –20 % +60 %, –20 % +50 %, –20 % < 2 times of the initial limit 2 V.DC to 6.3 V.DC : Within the initial limit DC leakage current 10 V.DC to 35V DC : < 3 times of the initial limit tan d Marking Dimensions (not to scale) – H + Cap. Polarity bar (Positive) P P L Lot No. W2 W2 W1 R.V. code Unit : mm Series CS Rated voltage mark d e g 2 V.DC 2.5 V.DC 4 V.DC j A C 6.3 V.DC 10 V.DC 16 V.DC D E V 20 V.DC 25 V.DC 35 V.DC L±0.2 W1±0.2 W2±0.1 H±0.1 7.3 4.3 2.4 1.1 P±0.3 1.3 CT 7.3 4.3 2.4 1.4 1.3 CX 7.3 4.3 2.4 1.9 1.3 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Reflow ✽3 Case size (mm) Series Rated Capacitance voltage (±20 %) (V.DC) (μF) ✽1 L W H Part number Min.✽4 Packaging Q’ty (pcs) ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 5100 15 4 120 7.3 4.3 1.1 EEFCS0G121R 3500 6.3 68 7.3 4.3 1.1 5100 15 EEFCS0J680R 3500 10 47 7.3 4.3 1.1 3200 40 EEFCS1A470R 3500 15 7.3 4.3 1.1 3200 40 EEFCS1C150R 3500 16 22 7.3 4.3 1.1 3200 40 EEFCS1C220R 3500 33 7.3 4.3 1.1 3200 40 EEFCS1C330R 3500 10 7.3 4.3 1.1 3200 40 EEFCS1D100R 3500 CS 20 15 7.3 4.3 1.1 3200 40 EEFCS1D150R 3500 22 7.3 4.3 1.1 3200 40 EEFCS1D220R 3500 10 7.3 4.3 1.1 3200 40 EEFCS1E100R 3500 15 7.3 4.3 1.1 3200 40 EEFCS1E150R 3500 35 10 7.3 4.3 1.1 3200 40 EEFCS1V100R 3500 4 180 7.3 4.3 1.4 5100 15 EEFCT0G181R 3500 6.3 100 7.3 4.3 1.4 5100 15 EEFCT0J101R 3500 10 68 7.3 4.3 1.4 3200 40 EEFCT1A680R 3500 16 47 7.3 4.3 1.4 3200 40 EEFCT1C470R 3500 25 CT Specification 33 7.3 4.3 1.4 3200 40 EEFCT1D330R 3500 47 7.3 4.3 1.4 3200 40 EEFCT1D470R 3500 25 22 7.3 4.3 1.4 3200 40 EEFCT1E220R 3500 35 15 7.3 4.3 1.4 3200 40 EEFCT1V150R 3500 20 ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Reflow ✽3 Case size (mm) Series Rated Capacitance voltage (±20 %) (V.DC) (μF) 220 270 2 2.5 330 390 470 560 220 330 390 470 150 180 4 220 270 330 100 120 CX 6.3 10 16 20 25 35 150 180 220 47 68 100 15 22 33 47 68 22 33 47 56 15 22 33 15 22 Specification ✽1 L W H 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 Part number Min.✽4 Packaging Q’ty (pcs) EEFCX0D221R EEFCX0D271XR EEFCX0D331R EEFCX0D331XR EEFCX0D391R EEFCX0D471R EEFCX0D561R EEFCX0E221R EEFCX0E331R EEFCX0E391R EEFCX0E471R EEFCX0G151R EEFCX0G181R EEFCX0G181XR EEFCX0G221R EEFCX0G221XR EEFCX0G271R EEFCX0G331R EEFCX0J101R EEFCX0J121R EEFCX0J151R EEFCX0J151XR EEFCX0J181R EEFCX0J221R EEFCX1A470R EEFCX1A680R EEFCX1A101R EEFCX1C150R EEFCX1C220R EEFCX1C330R EEFCX1C470R EEFCX1C680R EEFCX1D220R EEFCX1D330R EEFCX1D470R EEFCX1D560R EEFCX1E150R EEFCX1E220R EEFCX1E330R EEFCX1V150R EEFCX1V220R 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 5100 15 5600 12 5100 15 5600 12 5100 15 5100 15 5100 15 5100 15 5100 15 5100 15 5100 15 5100 15 5100 15 5600 12 5100 15 5600 12 5100 15 5100 15 5100 15 5100 15 5100 15 5600 12 5100 15 5100 15 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 3200 40 ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. 2 V.DC to 6.3 V.DC 10 V.DC to 35 V.DC Coefficient T < 45 °C 45 °C < T < 85 °C 85 °C < T < 105 °C 1.0 0.7 0.25 1.0 0.8 0.5 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : SX (Low ESR Products) Features ● Large capacitance (560 μF max.) ESR (4.5 mΩ to 9 mΩ) ● High ripple current (8500 mAr.m.s. max.) ● RoHS compliance, Halogen free ● Low Specifications Series Category temp. range Rated voltage range Nominal cap.range Capacitance tolerance DC leakage current Dissipation factor (tan d) Surge voltage (V.DC) Endurance Damp heat (Steady state) SX –55 °C to +105 °C 2 V.DC to 6.3 V.DC 82 μF to 560 μF ±20 % (120 Hz/+20 °C) I < 0.1 CV (μA) 2 minutes < 0.06 (120 Hz/+20 °C) Rated voltage × 1.25 (15 °C to 35 °C) +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 2 times of the initial limit DC leakage current < 3 times of the initial limit +60 °C, 90 %, 500 h, No-applied voltage 2 to 2.5 V.DC 4 V.DC Capacitance change of initial measurd value +70 %, –20 % +60 %, –20 % tan d < 2 times of the initial limit DC leakage current Within the initial limit Marking 6.3 V.DC +50 %, –20 % Dimensions (not to scale) – + H Cap. Polarity bar (Positive) P P Lot No. W1 W2 W2 L R.V. code Rated voltage mark d e g j 2 V.DC 2.5 V.DC 4 V.DC 6.3 V.DC Unit : mm Series SX L±0.2 W1±0.2 W2±0.1 H±0.1 7.3 4.3 2.4 1.9 P±0.3 1.3 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06 Mar. 2018 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Reflow ✽3 Case size (mm) Series Rated Capacitance voltage (±20 %) (V.DC) (μF) 180 220 270 330 2 390 470 560 150 180 220 270 SX 330 2.5 390 470 82 100 150 180 220 270 4 NEW NEW 6.3 NEW 330 120 150 180 220 Specification ✽1 L W H 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 Part number Min.✽4 Packaging Q’ty (pcs) EEFSX0D181ER EEFSX0D221ER EEFSX0D271ER EEFSX0D271XE EEFSX0D271E4 EEFSX0D331ER EEFSX0D331XE EEFSX0D331E4 EEFSX0D391ER EEFSX0D391XE EEFSX0D391E4 EEFSX0D471ER EEFSX0D471XE EEFSX0D471E4 EEFSX0D561E4 EEFSX0E151ER EEFSX0E181ER EEFSX0E221ER EEFSX0E221E7 EEFSX0E271E7 EEFSX0E331ER EEFSX0E331XE EEFSX0E331E4 EEFSX0E391ER EEFSX0E391XE EEFSX0E391E4 EEFSX0E471ER EEFSX0E471XE EEFSX0E471E4 EEFSX0G820ER EEFSX0G101ER EEFSX0G151ER EEFSX0G151E7 EEFSX0G181ER EEFSX0G221ER EEFSX0G271ER EEFSX0G331ER EEFSX0G331XE EEFSX0J121E7 EEFSX0J151ER EEFSX0J181ER EEFSX0J221ER 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 6300 9 6300 9 6300 9 7500 6 8500 4.5 6300 9 7500 6 8500 4.5 6300 9 7500 6 8500 4.5 6300 9 7500 6 8500 4.5 8500 4.5 6300 9 6300 9 6300 9 7000 7 7000 7 6300 9 7500 6 8500 4.5 6300 9 7500 6 8500 4.5 6300 9 7500 6 8500 4.5 6300 9 6300 9 6300 9 7000 7 6300 9 6300 9 6300 9 6300 9 7500 6 7000 7 6300 9 6300 9 6300 9 ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. T < 45 °C 45 °C < T < 85 °C 85 °C < T < 105 °C Coefficient 1.0 0.7 0.25 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06 Mar. 2018 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : GX (Super Low ESR Products) Features ● Large capacitance (560 μF max.) Low ESR (3 mΩ max.) ● Low ESL ( 3-terminals : 50 % less than 2-terminals) [Suffix : L] ● High ripple current (10200 mAr.m.s. max.) ● RoHS compliance, Halogen free ● Super Specifications Series Category temp. range Rated voltage range Nominal cap.range Capacitance tolerance DC leakage current Dissipation factor (tan d) Surge voltage (V.DC) Endurance Damp heat (Steady state) GX –55 °C to +105 °C 2 V.DC to 2.5 V.DC 330 μF to 560 μF ±20 % (120 Hz/+20 °C) I < 0.1 CV (μA) 2 minutes < 0.06 (120 Hz/+20 °C) Rated voltage × 1.25 (15 °C to 35 °C) +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 2 times of the initial limit DC leakage current < 3 times of the initial limit +60 °C, 90 %, 500 h, No-applied voltage Capacitance change of 2 V.DC to 2.5 V.DC initial measurd value +70 %, –20 % tan d < 2 times of the initial limit DC leakage current Within the initial limit Marking Cap. Polarity bar (Positive) Lot No. Rated voltage mark d 2 V.DC e 2.5 V.DC R.V. code Dimensions (not to scale) 2 terminals 3 terminals + – + H H – P P L L W1 W2 W2 + W2 – W2 W1 P4 P1 P3 P2 P1 Unit : mm Series GX L±0.2 7.3 W1±0.2 W2±0.1 H±0.1 4.3 2.4 1.9 ✽ Externals of figure are the reference. P±0.3 1.3 Unit : mm Series L±0.2 W1±0.2 W2±0.1 H±0.1 P1±0.3 P2±0.1 P3±0.2 P4±0.2 GX 7.3 4.3 2.4 1.9 1.3 1.1 0.7 1.4 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Apr. 2018 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Case size (mm) Series Rated Capacitance (±20 %) voltage (V.DC) (μF) 330 470 2 GX 560 NEW 2.5 330 470 Specification ✽1 L 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 W 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 H 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 10200 3 10200 3 10200 3 10200 3 10200 3 10200 3 10200 3 10200 3 The number of terminals 2 Reflow ✽3 Part number Min.✽4 Packaging Q’ty (pcs) EEFGX0D331R EEFGX0D471R EEFGX0D471L EEFGX0D561R EEFGX0D561L EEFGX0E331R EEFGX0E471R EEFGX0E471L 3500 3500 3500 3500 3500 3500 3500 3500 3 ○ ○ ○ ○ ○ ○ ○ ○ ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. T < 45 °C 45 °C < T < 85 °C 85 °C < T < 105 °C Coefficient 1.0 0.7 0.25 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 07 Apr. 2018 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : LX (Low ESR / Low ESL Products) Features ● Large capacitance (560 μF max.) ESR (4.5 mΩ, 6 mΩ) ● Low ESL (3-terminals : 50 % less than 2-terminals) ● High ripple current (8500 mAr.m.s. max.) ● RoHS compliance, Halogen free ● Low Specifications Series Category temp. range Rated voltage range Nominal cap.range Capacitance tolerance DC leakage current Dissipation factor (tan d) Surge voltage (V.DC) Endurance Damp heat (Steady state) LX –55 °C to +105 °C 2 V.DC to 2.5 V.DC 330 μF to 560 μF ±20 % (120 Hz/+20 °C) I < 0.1 CV (μA) 2 minutes < 0.06 (120 Hz/+20 °C) Rated voltage × 1.25 (15 °C to 35 °C) +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 2 times of the initial limit DC leakage current < 3 times of the initial limit +60 °C, 90 %, 500 h, No-applied voltage Capacitance change of 2 V.DC to 2.5 V.DC initial measurd value +70 %, –20 % tan d < 2 times of the initial limit DC leakage current Within the initial limit Marking Dimensions (not to scale) – H + Cap. Polarity bar (Positive) L W1 P4 Lot No. W2 + W2 – P1 R.V. code P3 P2 P1 Unit : mm Rated voltage mark d e 2 V.DC 2.5 V.DC Series L±0.2 W1±0.2 W2±0.1 H±0.1 P1±0.3 P2±0.1 P3±0.2 P4±0.2 LX 7.3 4.3 2.4 1.9 1.3 1.1 0.7 1.4 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Reflow ✽3 Case size (mm) Series Rated Capacitance voltage (±20 %) (V.DC) (μF) 330 2 LX 470 560 330 2.5 470 Specification ✽1 L W H 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 Part number Min.✽4 Packaging Q’ty (pcs) EEFLX0D331R EEFLX0D331R4 EEFLX0D471R EEFLX0D471R4 EEFLX0D561R EEFLX0D561R4 EEFLX0E331R EEFLX0E331R4 EEFLX0E471R EEFLX0E471R4 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 7500 6 8500 4.5 7500 6 8500 4.5 7500 6 8500 4.5 7500 6 8500 4.5 7500 6 8500 4.5 ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. T < 45 °C 45 °C < T < 85 °C 85 °C < T < 105 °C Coefficient 1.0 0.7 0.25 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : SR, LR, SS, LS, ST, LT Features ● Low profile (Height 1.0 mm max.) ● Low ESR (4.5 mΩ to 9 mΩ) ● Low ESL (3-terminals : 50% less then 2-terminals) ● High ripple current (8500 mAr.m.s. max.) ● RoHS compliance, Halogen free [LR, LS, LT series] Specifications Series Category temp. Range Rated voltage range Nominal cap.Range Capacitance tolerance DC leakage current Dissipation factor (tan d) Surge voltage (V.DC) Endurance Damp heat (Steady state) SR LR SS LS ST LT –55 °C to +105 °C 2 V.DC to 6.3 V.DC 2 V.DC to 2.5 V.DC 68 μF to 220μF 180 μF to 220μF 270 μF to 330 μF ±20 % (120 Hz / + 20 °C) I < 0.1 CV (μA) 2 minutes < 0.06 (120 Hz/+20 °C) Rated voltage × 1.25 (15 °C to 35 °C) +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 2 times of the initial limit DC leakage current < 3 times of the initial limit +60 °C, 90 %, 500 h, No-applied voltage 2 V.DC to 2.5 V.DC 4 V.DC 6.3 V.DC Capacitance change of initial measurd value +70 %, –20 % +60 %, –20 % +50 %, –20 % tan d < 2 times of the initial limit DC leakage current Within the initial limit Marking Cap. Polarity bar (Positive) Rated voltage mark Lot No. d e g j R.V. code 2 V.DC 2.5 V.DC 4 V.DC 6.3 V.DC Dimensions (not to scale) SR, SS, ST series LR, LS, LT series + – + H H – L P4 P W1 P1 P3 Unit : mm Series SR SS ST L±0.2 7.3 7.3 7.3 W1±0.2 W2±0.1 4.3 2.4 4.3 2.4 4.3 2.4 ✽ Externals of figure are the reference. W1 + W2 – W2 W2 L W2 P H±0.1 1.0 ✽1 1.1 1.4 P±0.3 1.3 1.3 1.3 ✽1 : Maximum P2 P1 Unit : mm Series LR LS LT L±0.2 W1±0.2 W2±0.1 7.3 4.3 2.4 7.3 4.3 2.4 7.3 4.3 2.4 H±0.1 1.0 ✽1 1.1 1.4 ✽ Externals of figure are the reference. P1±0.3 P2±0.1 P3±0.2 P4±0.2 1.3 1.1 0.7 1.4 1.3 1.1 0.7 1.4 1.3 1.1 0.7 1.4 ✽1 : Maximum Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Case size (mm) Series SR LR SS LS ST LT Rated Capacitance voltage (±20 %) (V.DC) (μF) 2 220 2.5 180 4 6.3 120 68 2 220 2.5 180 4 6.3 2 2.5 2 2.5 2 2.5 2 2.5 120 68 220 180 220 180 330 270 330 270 Specification ✽1 L 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 W 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 H 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.0 max. 1.1 1.1 1.1 1.1 1.4 1.4 1.4 1.4 ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 7500 6 8500 4.5 7500 6 8500 4.5 6300 9 6300 9 7500 6 8500 4.5 7500 6 8500 4.5 6300 9 6300 9 7500 6 7500 6 7500 6 7500 6 7500 6 7500 6 7500 6 7500 6 The number of terminals 2 Reflow ✽3 Part number Min.✽4 Packaging Q’ty (pcs) EEFSR0D221R EEFSR0D221R4 EEFSR0E181R EEFSR0E181R4 EEFSR0G121R EEFSR0J680R EEFLR0D221R EEFLR0D221R4 EEFLR0E181R EEFLR0E181R4 EEFLR0G121R EEFLR0J680R EEFSS0D221R EEFSS0E181R EEFLS0D221R EEFLS0E181R EEFST0D331R EEFST0E271R EEFLT0D331R EEFLT0E271R 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. T < 45 °C 45 °C < T < 85 °C 85 °C < T < 105 °C Coefficient 1.0 0.7 0.25 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Nov. 2015 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : CY, SY (Guaranteed at 85 °C) Features ● Endurance 85 °C 2000 h height (3.0 mm max.) ● High ripple current (5100 mAr.m.s. to 6300 mAr.m.s. max.) ● RoHS compliance, Halogen free ● Product Specifications Series CY / SY Category temp. range –55 °C to +85 °C Rated voltage range 4 V.DC, 6.3 V.DC Nominal cap.range 330 μF to 470 μF Capacitance tolerance ±20 % (120 Hz / + 20 °C) DC leakage current I < 0.1 CV (μA) [4 V.DC, 6.3 V.DC, 2 minutes] Dissipation factor (tan d) < 0.06 (120 Hz / + 20 °C) Rated voltage × 1.25 [4 V.DC, 6.3 V.DC] (15 °C to 35 °C) Surge voltage (V.DC) +85 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 2 times of the initial limit DC leakage current < 3 times of the initial limit +60 °C, 90 %, 500 h, No-applied voltage 4 V.DC Capacitance change of initial measurd value +60 %, –20 % tan d < 2 times of the initial limit Damp heat (Steady state) 6.3 V.DC +50 %, –20 % DC leakage current Within the initial limit Marking Dimensions (not to scale) – + H Cap. Polarity bar (Positive) P P L Lot No. W2 W2 W1 R.V. code Unit : mm Rated voltage mark g j 4 V.DC 6.3 V.DC Series CY/SY L±0.2 W1±0.2 W2±0.1 H±0.2 7.3 4.3 2.4 2.8 P±0.3 1.3 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Jul. 2017 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Reflow ✽3 Case size (mm) Series CY SY Rated Capacitance voltage (±20 %) (V.DC) (μF) Specification ✽1 L W H Part number Min.✽4 Packaging Q’ty (pcs) ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 5100 15 4 470 7.3 4.3 2.8 ECGCY0G471R 2000 6.3 330 7.3 4.3 2.8 5100 15 ECGCY0J331R 2000 4 470 7.3 4.3 2.8 6300 9 ECGSY0G471R 2000 6.3 330 7.3 4.3 2.8 6300 9 ECGSY0J331R 2000 ✽1: Ripple current (100 kHz/ +45°C ) ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. T < 45 °C 45 °C < T < 65 °C 65 °C < T < 85 °C Coefficient 1.0 0.7 0.25 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Jul. 2017 Conductive Polymer Aluminum Electrolytic Capacitors Surface Mount Type Series : HX (Guaranteed at 125 °C) Features ● Endurance 125 °C 1000 h voltage & Large capacitance (2 V.DC 560 μF to 25 V.DC 33 μF) ● Low ESR (4.5 mΩ max.) ● RoHS compliance, Halogen free ● High Specifications Series Category temp. range Rated voltage range Category voltage range Nominal cap.range Capacitance tolerance DC leakage current Dissipation factor (tan d) Surge voltage (V.DC) Endurance Damp heat (Steady state) HX –55 °C to +125 °C 2 V.DC to 2.5 V.DC, 10 V.DC to 25 V.DC 1.6 V.DC to 2 V.DC, 8 V.DC to 20 V.DC 15 μF to 560 μF ±20 % (120 Hz/+20 °C) 2 V.DC to 2.5 V.DC : I < 0.1 CV (μA) 2 minutes, 10 V.DC to 25 V.DC : I < 0.3 CV (μA) 2 minutes < 0.1 (120 Hz/+20 °C) Rated voltage × 1.25 [2 V.DC to 16 V.DC], × 1.15 [20 V.DC to 25 V.DC](15 °C to 35 °C) +125 °C, 1000 h, Category voltage applied Capacitance change Within ±20 % of the initial value tan d < 2 times of the initial limit DC leakage current Within the initial limit After storing for 500 hours at +60 °C, 90 % 2 V.DC to 2.5 V.DC 10 V.DC to 25 V.DC Capacitance change of initial measurd value +70 %, –20 % +60 %, –20 % tan d < 2 times of the initial limit 2 V.DC to 2.5 V.DC : Within the initial limit DC leakage current 10 V.DC to 25V DC : < 3 times of the initial limit Marking Dimensions (not to scale) – + H Cap. Polarity bar (Positive) P P Lot No. W1 W2 W2 L R.V. code Rated voltage mark d e A 2 V.DC 2.5 V.DC 10 V.DC Unit : mm C D E 16 V.DC 20 V.DC 25 V.DC Series HX L±0.2 W1±0.2 W2±0.1 H±0.1 7.3 4.3 2.4 1.9 P±0.3 1.3 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Mar. 2018 Conductive Polymer Aluminum Electrolytic Capacitors Characteristics list Reflow ✽3 Series Rated voltage [105 °C] (V.DC) Category Capacitance voltage (±20 %) [125 °C] (μF) (V.DC) 470 2 1.6 560 330 2.5 2 470 HX 47 10 16 20 25 8 12.8 16 20 Case size (mm) Specification ✽1 L W H 7.3 4.3 1.9 7.3 4.3 1.9 ✽2 Ripple ESR current (mAr.m.s.) (mΩ max.) 5100 15 6300 9 Part number Min.✽4 Packaging Q’ty (pcs) EEFHX0D471R 3500 EEFHX0D471R9 3500 7.3 4.3 1.9 7500 6 EEFHX0D471R6 3500 7.3 4.3 1.9 8500 4.5 EEFHX0D471R4 3500 7.3 4.3 1.9 5100 15 EEFHX0D561R 3500 7.3 4.3 1.9 8500 4.5 EEFHX0D561R4 3500 7.3 4.3 1.9 5100 15 EEFHX0E331R 3500 7.3 4.3 1.9 6300 9 EEFHX0E331R9 3500 7.3 4.3 1.9 7500 6 EEFHX0E331R6 3500 7.3 4.3 1.9 8500 4.5 EEFHX0E331R4 3500 7.3 4.3 1.9 5100 15 EEFHX0E471R 3500 7.3 4.3 1.9 6300 9 EEFHX0E471R9 3500 7.3 4.3 1.9 7500 6 EEFHX0E471R6 3500 7.3 4.3 1.9 8500 4.5 EEFHX0E471R4 3500 7.3 4.3 1.9 3200 40 EEFHX1A470R 3500 68 7.3 4.3 1.9 3200 40 EEFHX1A680R 3500 100 7.3 4.3 1.9 3200 40 EEFHX1A101R 3500 15 7.3 4.3 1.9 3200 40 EEFHX1C150R 3500 22 7.3 4.3 1.9 3200 40 EEFHX1C220R 3500 33 7.3 4.3 1.9 3200 40 EEFHX1C330R 3500 47 7.3 4.3 1.9 3200 40 EEFHX1C470R 3500 68 7.3 4.3 1.9 3200 40 EEFHX1C680R 3500 22 7.3 4.3 1.9 3200 40 EEFHX1D220R 3500 33 7.3 4.3 1.9 3200 40 EEFHX1D330R 3500 47 7.3 4.3 1.9 3200 40 EEFHX1D470R 3500 56 7.3 4.3 1.9 3200 40 EEFHX1D560R 3500 15 7.3 4.3 1.9 3200 40 EEFHX1E150R 3500 22 7.3 4.3 1.9 3200 40 EEFHX1E220R 3500 33 7.3 4.3 1.9 3200 40 EEFHX1E330R 3500 ✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C) ✽3: Please refer to the page of “Mounting Specifications”. ✽4: Please contact us when 500 pcs packing is necessary. Temperature compensation multipliers for ripple current Temp. 2 V.DC to 2.5 V.DC 10 V.DC to 25 V.DC Coefficient T < 45 °C 45 °C < T < 85 °C 85 °C < T < 105 °C 105 °C < T < 125 °C 1.0 0.7 0.25 0.25 1.0 0.8 0.5 0.25 Ripple current should be controlled so that surface temperature of capacitor does not exceed the category temperature. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 05 Mar. 2018 SP-Cap/ Conductive Polymer Aluminum Capacitors (Specialty Polymer Aluminum Capacitors) Surface Mount Type Series: FD, CD, UD, UE Old series [Our Requests] Since this series is old, we don't recommend you to adopt it but CX & SX series for your new design. ■ Features ● Low ESR ● Excellent Noise-absorbent Characteristics ● RoHS directive compliant ■ Specifications Series & Size Code FD CD Category Temp. Range UD UE –40 °C to +105 °C Rated Voltage Range 2 V.DC to 12.5 V.DC 2 V.DC to 16 V.DC 2 V.DC to 8 V.DC 2 V.DC to 8 V.DC Nominal Cap.Range 15 μF to 68 μF 2.2 μF to 220 μF 68 μF to 470 μF 100 μF to 560 μF Capacitance Tolerance ±20 % Reflow 240 °C : I < 0.06 CV (μA) 2minutes (2 V.DC to 4 V.DC) I < 0.04 CV or 3 (μA) 2 minutes (6.3 V.DC to 16 V.DC) (Whichever is greater) Reflow 260 °C : I < 0.1 CV (μA) 2 minutes < 0.06 (120 Hz/+20 °C)