EETEE2G391KJ

Aluminum Electrolytic Capacitors/ EE Snap-in Type Series: EE Type: TS ■ Features ● Endurance : 105 °C 3000 h ● Miniaturize (Maximum Ripple Current) Low profile ● RoHS directive compliant ■ Specifications Category Temp. Range Rated W.V. Range Nominal Cap. Range Capacitance Tolerance –40 °C to +105 °C 200 V.DC, 250 V.DC 220 µF to 1800 µF –25 °C to +105 °C 400 V.DC, 450 V.DC 75 µF to 560 µF ±20 % (120 Hz/+20 °C) 3앀 CV (µA) max. After 5 minutes application of rated working voltage at +20 °C C : Capacitance (µF) V: W.V. (V.DC) DC Leakage Current tan δ Please see the attached standard products list Frequency (Hz) 50 60 100 Frequency Correction 200V.DC, 250V.DC 0.75 0.80 0.95 Factor for Ripple Current 400V.DC, 450V.DC 0.75 0.80 0.95 120 1.00 1.00 500 1.20 1.20 1 k 1.25 1.25 10 k to 1.30 1.40 After 3000 hours application of DC voltage with specified ripple current (< rated DC working voltage) at +105 °C±2 °C, the capacitors shall meet the following limits. Capacitance change tan δ DC leakage current Endurance < ±20 % of initial measured value < 200 % of initial specified value < initial specified value After storage for 1000 hours at +105 °C±2 °C within no voltage applied and then being stabilized at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment) Shelf Life ✽ A formula to calculate estimated lifetime of TS-EE Series is different from other series. Please contact us. ■ Dimensions in mm (not to scale) φD+1.0 max. Polarity bar (mm) 2-φ2.0±0.1 (1 Sleeve 0.0 ) 10 .0± 0.1 Vent L+2.0 max. (φD) 4.0±0.5 Rated voltage etc. indicate to sleeve. Recommended PWB piercing plan 4.0±0.5 +0.2 2.0 max. Terminal (t=0.8) (3.5) 0.8 –0.1 1.5±0.2 Top of spin Standard terminal type does not require terminal trimming process Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ EE ■ Standard Products Case size Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) Min. Packaging Q'ty W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 300 22 25 EETEE2D301HJ 1.70 0.15 200 390 22 30 EETEE2D391HJ 2.17 0.15 200 470 22 35 EETEE2D471HJ 2.22 0.15 200 22 40 EETEE2D591HJ 2.30 0.15 200 590 700 590 800 200 25 30 EETEE2D591JJ 2.30 0.15 200 22 45 EETEE2D701HJ 2.65 0.15 200 25 35 EETEE2D701JJ 2.65 0.15 200 30 25 EETEE2D591KJ 3.08 0.15 200 22 50 EETEE2D801HJ 3.08 0.15 200 25 40 EETEE2D801JJ 3.08 0.15 200 30 30 EETEE2D801KJ 3.48 0.15 200 35 25 EETEE2D801LJ 3.48 0.15 200 25 50 EETEE2D102JJ 3.48 0.15 200 1000 30 35 EETEE2D102KJ 3.98 0.15 100 35 30 EETEE2D102LJ 4.20 0.15 200 1200 30 40 EETEE2D122KJ 4.20 0.15 100 1300 30 45 EETEE2D132KJ 4.62 0.15 100 35 40 EETEE2D152LJ 4.62 0.15 100 100 1500 ✽ (pcs) 30 50 EETEE2D152KJ 5.22 0.15 1800 35 45 EETEE2D182LJ 5.22 0.15 100 220 22 25 EETEE2E221HJ 1.43 0.15 200 22 30 EETEE2E301HJ 1.56 0.15 200 25 25 EETEE2E301JJ 1.70 0.15 200 22 35 EETEE2E371HJ 1.70 0.15 200 22 40 EETEE2E421HJ 1.82 0.15 200 300 370 420 520 420 250 590 25 30 EETEE2E421JJ 1.82 0.15 200 22 45 EETEE2E521HJ 2.00 0.15 200 25 35 EETEE2E521JJ 2.00 0.15 200 30 25 EETEE2E421KJ 2.20 0.15 200 22 50 EETEE2E591HJ 2.30 0.15 200 25 40 EETEE2E591JJ 2.30 0.15 200 30 30 EETEE2E591KJ 2.50 0.15 200 35 25 EETEE2E591LJ 2.50 0.15 200 25 45 EETEE2E731JJ 2.70 0.15 200 730 30 35 EETEE2E731KJ 3.00 0.15 100 35 30 EETEE2E731LJ 3.00 0.15 200 860 30 40 EETEE2E861KJ 3.30 0.15 100 1000 30 45 EETEE2E102KJ 3.45 0.15 100 ✽ 1300 35 45 EETEE2E132LJ 3.75 0.15 100 ✽ 1500 35 50 EETEE2E152LJ 4.05 0.15 100 Endurance : 105 °C 3000 h Terminal Pitch : 10 mm ✽ When capacitors of φ35×45L and φ35×50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ EE ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 22 25 EETEE2G1O1HJ 0.95 0.15 200 30 EETEE2G121HJ 1.22 0.15 200 150 22 35 EETEE2G151HJ 1.33 0.15 200 25 30 EETEE2G181JJ 1.33 0.15 200 320 330 370 30 25 EETEE2G181KJ 1.68 0.15 200 22 45 EETEE2G221HJ 1.55 0.15 200 25 35 EETEE2G221JJ 1.55 0.15 200 30 30 EETEE2G221KJ 1.79 0.15 200 35 25 EETEE2G221LJ 1.79 0.15 200 22 50 EETEE2G271HJ 1.68 0.15 200 25 40 EETEE2G271JJ 1.68 0.15 200 30 35 EETEE2G271KJ 2.12 0.15 100 25 45 EETEE2G321JJ 1.90 0.15 200 30 40 EETEE2G331KJ 2.33 0.15 100 35 30 EETEE2G331LJ 2.33 0.15 200 200 25 50 EETEE2G371JJ 2.12 0.15 30 45 EETEE2G391KJ 2.52 0.15 100 35 35 EETEE2G391LJ 2.52 0.15 100 30 50 EETEE2G471KJ 2.85 0.15 100 35 40 EETEE2G471LJ 2.85 0.15 100 560 35 45 EETEE2G561LJ 3.18 0.15 100 75 22 25 EETEE2W750HJ 0.83 0.20 200 22 30 EETEE2W101HJ 0.95 0.20 200 25 25 EETEE2W101JJ 0.95 0.20 200 22 35 EETEE2W121HJ 1.15 0.20 200 25 30 EETEE2W121JJ 1.22 0.20 200 30 25 EETEE2W121KJ 1.22 0.20 200 390 470 100 120 150 180 450 22 40 EETEE2W151HJ 1.22 0.20 200 22 45 EETEE2W181HJ 1.38 0.20 200 25 40 EETEE2W181JJ 1.38 0.20 200 30 30 EETEE2W181KJ 1.60 0.20 200 35 25 EETEE2W181LJ 1.60 0.20 200 220 25 45 EETEE2W221JJ 1.55 0.20 200 250 35 30 EETEE2W251LJ 1.90 0.20 200 25 50 EETEE2W271JJ 1.74 0.20 200 30 40 EETEE2W271KJ 1.90 0.20 100 270 300 330 ✽ (pcs) 22 270 ✽ Min. Packaging Q'ty 120 220 ✽ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 100 180 400 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) 390 470 35 35 EETEE2W301LJ 2.20 0.20 100 30 45 EETEE2W331KJ 2.20 0.20 100 35 40 EETEE2W331LJ 2.40 0.20 100 30 50 EETEE2W391KJ 2.40 0.20 100 35 45 EETEE2W391LJ 2.61 0.20 100 35 50 EETEE2W471LJ 2.85 0.20 100 Endurance : 105 °C 3000 h Terminal Pitch : 10 mm ✽ When capacitors of φ35×45L and φ35×50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008