Messrs.
Issue No.
: PC-02-068
Date of issue : November 15, 2002
Classification : New Change Renewal
Digi-Key
Delivery Specification
Product Description
Product Part Number
: Balun
: EHF2BG0920
Classification of Spec
Applications
: Individual Product Specification
: Cellular phone
For other applications, contact the undersigned in advance.
: November 14, 2007 from the date of issue.
Term of Validity
CUSTOMER USE ONLY
Receipt Record#:
This was certainly received by us.
1(one) copy is being returned to you.
Date of receipt:
Received by:
Title:
Dept.:
Matsushita Electronic Components Co., Ltd.
Network Device Company
Module Strategic Business Unit
Engineering Group HFD Team
Prepared by
Checked by
: H. Ito
: M. Mizuno
992-1 Aiba Ohno-cho Ibi-gun Gifu 501-0598 JAPAN
Tel: +81-0585-36-2322
Fax: +81-0585-36-2344
Authorized by
Title
: M. Mizuno
: Manager of Engineering
[Shape, appearance, dimension] Unit: mm
GND
(5)
OUT2
(4)
(1)
IN
(2)
GND
(3)
OUT1
2.0+/-0.1
(4)
(5)
(6)
(3)
(2)
(1)
0.95+/-0.1
1.25+/-0.1
NU
(6)
Sn-Pb (Sn:Pb=9:1) or Sn
Ni
Ceramic substrate
Ag-Pd
Note 1) “typ” is used where no dimensional tolerance applies.
Item
Appearance/
construction
Description
Product surface shall be covered with a protective film, which does not
easily separate nor present noticeable unevenness, scratches, pinholes,
color changes etc.
Terminals shall ensure practically acceptable quality.
Substrate shall be as shown in the drawing with no excessive chippings,
scratches, burrs, or cracks.
Marking
Remarks
Shall be legible in black (with printing paste).
marked side for pin 1.
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Appearance
Drawing No.
151-EHF-2BG0920
9-1
[Absolute maximum ratings]
No.
Item
Symbol
Rating
Unit
1 Maximum input power Pmax 100
2 Operating temperature Topr -30…+85
3 Storage temperature
Tstg -40…+85
Note: This component cannot apply a DC Bias.
[Electrical characteristics]
No.
Item
1 Frequency
2
3
4
5
Insertion loss (Back to back)
Unbalance impedance
Balance impedance
Unbalance port VSWR
6 Amplitude balance
7 Phase balance
[Internal circuitry]
Remarks
mW DC voltage is 0V.
degC
degC
T=-30…+85degC
Specification
Test
Circuit
-
Min.
880
Typ.
-
Max.
960
MHz
Fig-2
Fig-1
-
50
200
-
1.0
2.0
dB
ohm
ohm
-
Fig-1
Fig-1
-1.5
165
180
1.5
195
dB
deg
(1)IN
(5)GND
(2)GND
(4)OUT2
(3)OUT1
[Measuring circuit]
< Phase balance measurement >
•Phase1
A=IN, B=OUT, C=Terminal resistor (50 ohm)
•Phase2
A=IN, C=OUT, B=Terminal resistor (50 ohm)
•Phase balance
Phase balance=Phase1-Phase2
< Insertion loss measurement >
Assuming the loss as “Loss” when D=IN, E=OUT
Insertion loss for a device is “Loss”/2
NETWORK ANALYZER
S-PARAMETER
TEST SET
IN
OUT
C
FIG.1
Unit
GND
GND
A
FIG.2
Matching
Resistor
47 ohm
GND
B
E
D
GND
GND
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Specification and measurement
Drawing No.
151-EHF-2BG0920
9-2
[Terminal dimensions] Unit: mm
Pin No.
0.65
0.65
(5)
(6)
0.65
0.3
(4)
0.3
Bottom View
0.2
(3)
0.3
(2)
(1)
0.35
Tolerance of
Terminal dimensions : +/-0.15
(6)
NU
(4)
OUT2
IN
(1)
GND
(2)
0.35
0.3
OUT1
(3)
Delivery Specification
Enact. Date
November 15, 2002
November 15, 2002
PCB Pad
Top View
Balun
Enfo. Date
(5)
GND
Product
0.65
1.0
2.65
1.0
[Recommended PCB pad dimensions] Unit: mm
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Terminals/Recommended lands
Drawing No.
151-EHF-2BG0920
9-3
[Quality characteristics]
Test item
Test condition
Judgment criteria
No abnormality shall
be observed in
appearance or
electrical
characteristics.
High temperature
+85degC, 1000h
Low temperature
-40degC, 1000 h
High-temperature high-humidity storage
+60degC, 90%RH, 1000h
Pressure Pot
+121degC, 99%RH, 2.026x10 Pa, 100h
Temperature cycling
-40…+85degC, Each 30 min., 200cy
Vibration
10…500Hz, 10G, in each direction of XYZ, 2h30min.
Impact
100G, 6mS, Half sinusoidal wave, in each direction of XYZ, 3 times
Shock (Drop)
1.8m , 6 facesx6cy(36 times with 100g Dummy Load)
Electro static discharge
200pF, 0 ohm, +/-200V, Each 5 times
Soldering heat resistance
Manual hot gas: 260+/-10degC, 30 sec., 2 times
5
Over 90% of the terminal
surface shall be covered
with solder.
Soldering iron: 260+/-10degC, 3 sec., 2 times
Reflow: 260degC peak, 2 times
Solder ability
Over 95% of the terminal
surface shall be covered
with solder.
Solder bath: 235+/-5degC, 2 sec.
Reflow: 230degC
Board warping
Assemble this component on a PC board with 0.8mm thickness using
the recommended soldering condition shown below, and apply a
bending force of 3mm warping at a rate of 1mm/sec. 5 seconds and 5
times.
45mm
45mm
t=0.8mm
3mm
There should not be
any cracks in the
component or solder
joints, no abnormality
in electrical
characteristics.
Terminal removal
Solder a component on a PC board using the recommended condition shown below and
then press the component sideways at 1mm/sec. Destruction limit 9.8N or greater.
Seating plane co-planarity
Within 0.1mm
< Recommended soldering condition >
Diagram1
Shown below is a recommended reflow soldering condition .
Temperature
degC
250
230
200
170
140
30~60 sec.
Balun
Delivery Specification
Enact. Date
Enfo. Date
60~180 sec.
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
Time
EHF2BG0920
Quality Characteristics
Drawing No.
151-EHF-2BG0920
9-4
[Cautions for use]
(1) Operating a product over the maximum rating for even a moment may result in a
product failure or breakage. Never use a product in such a condition that it may
cause a safety problem.
(2) Opening or short-circuiting the product terminals or inserting a product in the
reverse orientation while power is being supplied may cause a breakage. Always
avoid such circumstances.
(3) Operations in a corrosive gas atmosphere or improper environments such as hightemperature, high-humidity or dewy conditions may lead to product performance
deterioration, a breakage, a change in appearance etc. Please avoid such
conditions, as they are unsafe.
(4) Always ground the soldering iron or soldering bath used for assembly operation to
avoid any excessive voltage applied to a product.
(5) After soldering with solder bridges, incomplete soldering or in the reverse
orientation, supplying power may result in a product breakage. Please confirm the
soldered condition before supplying power to the product.
(6) Excessive stress on the terminals may cause a contact failure or performance
deterioration. Please use caution.
(7) Please provide a fail-safe provision in the product you design by taking any failure
of our product into consideration.
(8) This product does not include a DC-cutting device. Application of a DC voltage
between the Balance port and the Unbalance port may cause product deterioration
or breakage.
* If any question arises about the safety of this product, please contact us immediately with a
request for an engineering examination.
[Remarks]
*1: All of the materials used in this product are those listed as the existing chemical
substances based on the “Law for examination and regulation of manufacture of
chemical substances”.
*2: The production process of this product does not use any ozone-depleting
chemicals (OZC) regulated by the Montreal Protocol.
*3: Validity of this specification is 5 years from the date of issue, but the validity is
considere d on going unless any changes are made.
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Cautions
Drawing No.
151-EHF-2BG0920
9-5
[Packaging materials]
1. Materials
1) Embossed carrier tape (Refer to the attachment)
2) Top tape: Anti-static
3) Packaging box (Refer to the attachment)
4) Packaging tape, carrier-securing adhesive tape
2. Specification
No.
Item
1 Reel outer diameter
2
3
4
5
Condition
Refer to the attachment .
Reel inner diameter Refer to the attachment .
Reel inner width Refer to the attachment .
Quantity in a reel 4000 pieces/reel
Taping direction
6 Top tape
attachment
position
Remarks
Tape unreeling direction
(with markings facing up)
Top tape
8.0+/-0.2mm
5.5mm
< Top tape attachment area >
Embossed tape
Top tape edge must stay inside the sprocket holes of the embossed
carrier (Sprocket holes shall not be covered).
Tape unreeling direction
7 Label attachment
position
Label
Tape breaks force.
Min. 10N
Top cover tape strength.
Min. 10N
Tape peel force.
0.1…1.0N
Tape peel angle.
165…180degree
Reel weight.
Max 1500g
Indicated Item
Pat No., Lot No.
Quantity, Maker
Country of Origin
Leader part
8 Tape leader part
and tape ending
part
Ending part
Product -loaded part Embossed carrier
200~220mm
(Product-unloaded part)
100~150mm, 25~38 pieces
worth, (Product-unloaded part)
9 Missing products No missing products shall be allowed.
10 Packaged quantity in a box 21 reels/box (Max)
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
Top tape
300~
400mm
84000 pieces/box(Max)
EHF2BG0920
Packaging specification 1
Drawing No.
151-EHF-2BG0920
9-6
1. Method
1) Load products in each cavity of an embossed carrier tape, in the correct orientation, by
leaving the product-unloaded part shown in Item No. 8(P9-6) of the packaging specification.
2) Heat-seal a top tape in good alignment on the carrier tape.
3) After 4000 pieces are loaded and reeled, provide a product-unloaded part at the tape-leader
portion. Secure the tip of the carrier tape with a piece of adhesive tape.
4) Stack the reels (21 reels max.) and enclose them in a packaging box. Close the flaps with a
piece of adhesive tape.
5) Provide markings on the packaging box.
< Items to be indicated >
1. Part No.
2. Quantity
3. Lot No.
4. Manufacturer name
5. Country of origin
Marking on the packaging box
Packaging box shape varies
with the number of reels enclosed.
Reel label
Number of
stacking, 21
reels max.
* Insert cushion material in the empty
spaces to secure reels .
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Packaging specification 2
Drawing No.
151-EHF-2BG0920
9-7
[Embossed tape dimensions] Unit: mm
2+/-0.05
+0.1
0.25+/-0.05
2.25 +/-0.1
8+/-0.2
d1.5-0
+/-0.1
3.5 +/-0.05 1.75
4+/-0.1
(5.0deg)
+0.2
4+/-0.1
1.05+/-0.1
d1.0 -0
(5.0deg)
1.45+/-0.1
(1) Unspecified corner radius shall be 0.3mm max.
(2) Cumulative pitch error of sprocket holes shall be +/-0.2mm for 10 pitches.
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Packaging specification 3
Drawing No.
151-EHF-2BG0920
9-8
ƒÓ
A ƒÓ
18
0
-3
0
R85
ƒÓ
3
[Reel dimensions] Unit: mm
(1) This reel conforms to EIAJ -RRM-08B based on EIAJ standard.
(2) Material: PS (Polystyrene)
44
Center area
.2
H
} 0
•
1
2-R
18
.0
2
2-R1
2
} 0.
•
MI
N
.0
18
‹
•
120
120 •
‹
N
MI
2•} 0.2
2
R10.5 •} 0.
2
N ƒ
Ó 60+1
0
W1
10
W2
ƒÓ
MIN 18.0
3 •} 0.2
ƒ
Ó 13
B
5
R0.
ƒ
Ó 3
4
3 B
3 B
Label
105...50
0.2
0.4
0.6
0.8
0.8
0.6
H
0.4
0.2
5
4
Scale
3
Rim , Hub
Rim A
180
0
-3
Hub N
60
+1
0
Inner width , Outer width
Tape width
8
Inner width W1 Outer width W2
9+/-0.3
11+/-1.0
Number
105
110
Balun
Delivery Specification
Enact. Date
Enfo. Date
November 15, 2002
November 15, 2002
P.S.M
Approval
Check
Plan
-----
M. Mizuno
M. Mizuno
H. Ito
EHF2BG0920
Packaging specification 4
Drawing No.
151-EHF-2BG0920
9-9