PIR MOTION SENSORS 2019
Special designs from Panasonic that provide high sensitivity and reliability
02
PIR MOTION SENSORS
Pyroelectric infrared motion sensors from Panasonic for optimal usability and reliability
Panasonic develops and produces PIR motion sensors, which combine easy integration, high reliability and environment-friendly materials.
The Panasonic PIR motion sensors abbreviated as PaPIRs, have different series of products, including:
AMN NaPiOn: 2nd generation
EKM PaPIRs: 3rd generation
EKMB (WL) digital output for battery-operated devices (1, 2, 6μA)
AMN3 digital output for battery-free devices (170μA)
EKMC (VZ) digital and analog output for battery-free devices (170μA)
Available lens colors: white and black
Available lens colors: white, black and pearl white
Applications
Multi-function printers,
video-conference systems
Lighting controls in general,
smart luminaires,
smart LED bulbs
Thermostats,
HVAC (heater,
ventilator or
air conditioner)
Digital signage,
vending machine
Wake-up switch for LCD
displays and panels
IP cameras, intrusion alarms
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
Smart home and
IoT applications
CONTENT
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
AMN - Standard Detection Type . . . . . . . . . . . . . . . . . . . . 18
PaPIRs design features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
AMN - Slight Motion Detection Type . . . . . . . . . . . . . . . . . 19
Technical information for all sensors (EKM and AMN) . . . . 6
AMN - Spot Detection Type . . . . . . . . . . . . . . . . . . . . . . . 20
EKM - Standard Detection Type . . . . . . . . . . . . . . . . . . . . . 7
AMN - 10m Detection Type (long distance) . . . . . . . . . . . 21
EKM - Low Profile Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AMN - Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
EKM - Slight Motion Detection Type . . . . . . . . . . . . . . . . . . 9
Cautions for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
EKM - Standard and Slight Motion Detection Type . . . . . 10
EKM - High Density Long Distance Detection Type . . . . . 11
EKM - Horizontally Wide Detection Type . . . . . . . . . . . . . 12
EKM - Wall Installation Detection Type (corner) . . . . . . . . 13
EKM - Long Distance Detection Type . . . . . . . . . . . . . . . . 14
EKM - Lensless Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
EKM - Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
EKMB1
■ Ordering
information
● PaPIRs
1
● Others
K: 6μA
motion sensor
● Current
1: 1μA /
consumption in standby mode
2: 2μA / 3: 6μA
● Detection（ Lens ）
00: Lensless / 01: 5m distance standard / 03: 12m long distance
04: Wall installation type / 05: Horizontally wide type /
06: High density long distance type / 07: Low profile type
/
/ Blank: Other than 6μA
● Lens color
0: Lensless / 1: White /
2: Black / 3: Pearl white
● Lens
0: Lensless / 1: with lens
EKMC160010
● PaPIRs
motion sensor
● Sensor type
1: Digital / 2:
● Lens color
0: Lensless / 1: White /
2: Black / 3: Pearl white
Analog
● Detection（ Lens ）
00: Lensless / 01: 5m distance standard / 03: 12m long distance
04: Wall installation type / 05: Horizontally wide type /
06: High density long distance type / 07: Low profile type
/
● Lens
0: Lensless
/ 1: with lens
AMN 3 11
● NaPiOn
sensor
● Lens color
1: Black / 2:
White
● Detection（ Lens ）
1: Standard type / 2: Slight
3: Spot type / 4: 10m type
motion type /
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
03
04
PIR MOTION SENSORS
PaPIRs design features
The PIR motion sensors from Panasonic offer crucial advantages over conventional PIR motion sensors. The unique design concept
(explained below) ranges from the production of the pyroelectric sensing devices to the internal signal processing, thus guaranteeing an optimal detection capability and high reliability.
Easy design-in
Small and fancy lens design
The integrated amplifier / comparator circuit inside a TO-5 metal
can (digital type) prevents interferences caused by electromagnetic fields, such as those generated by cell phones and
wireless devices. A special differential circuit design is introduced for the EKMB 6μA type for applications where a high
noise resistance is required (up to GHz range).
Thanks to the special design of the small pyroelectric elements, it is possible to use a smaller lens size while keeping
the same detection area and distance compared to conventional sensors.
PaPIRs
Conventional
PIR element size
1.1×1.1mm
Small multilens
TO-5 metal can
0.6mm
0.4mm
High sensitive quad pyroelectric
0.6mm
element with slit design
0.6mm
ASIC inside (amplifier and comparator)
0.4mm
0.6mm
"Plug and Play"
Lens
Reduced focal length
(Distance from element to lens)
Radiation noise
No false
alarms
VDD
OUT
GND
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
Detection zones
PIR MOTION SENSORS
Two times better sensitivity
The sensitivity has been significantly improved thanks to a
unique slit design of the pyroelectric elements. The separated
sensing areas prevent thermal crosstalk between the single
sensing elements. Therefore, reliable detection is possible even
if the temperature difference between the background
(e.g. floor / wall) and the target object (human) is small.
(e.g. ∆T = 4°C)
Element without slit design
Element with slit design
Four times better signal-to-noise ratio
Improved signal-to-noise ratio thanks to a special I/V circuit
which is used for converting a current signal from the pyroelectric element to voltage. Panasonic PIR motion sensors perform
by the feedback capacitor and the operational amplifier, different
from the conventional FET-type, thereby decreasing the probability of false alarms due to temperature fluctuation.
Conventional PIR (JFET)
PaPIRs (op amp)
DC current
feedback circuit
FET
Op amp
Rg
Temperature distribution of
conventional pyroelectric
sensors without slit design
Temperature distribution of
Panasonic’s pyroelectric infrared
sensors with slit design
Lead-free pyroelectric element
A ferroelectric Lithiumtantalate (LiTaO3) single lead-free crystal is
used as the pyroelectric element for Panasonic PIR motion sensors. Conventional PIR motion sensors normally use a ceramic
base material (e.g. PZT) for the pyroelectric element, which contains lead in many cases.
PaPIRs: High signal-to-noise ratio
Threshold
Analog output
diagram
Conventional types: Low signal-to-noise ratio
Threshold
Low current consumption EKMB (WL)
Reduction of current consumption (1, 2 or 6μA) thanks to the
special circuit design technology allows battery life to be
extended for battery-driven products.
Threshold
Analog output
diagram
Threshold
False alarm
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
05
06
PIR MOTION SENSORS
Technical information for all sensors (EKM and AMN)
Block diagram output circuit
ASIC
TO-5
Digital output with integrated
amplifier and comparator
Infrared
radiation
VDD
Stabilized power
I/V
Multilens
Amp
Comparator
Output
GND
PIR sensor
Optical filter
ASIC
Analog output with
integrated amplifier
TO-5
Infrared
radiation
Stabilized power
I/V
Multilens
Amp
VDD
Output
GND
PIR sensor
Optical filter
Wiring diagram
Digital output
Sensor
Sensor
VDD
VDD
GND
GND
Load
Out
Out
Microcomputer,
A/D converter, etc.
IOUT: max. 100μA
IOUT: max. 100μA
Analog output
Sensor
VDD
GND
Out
Microcomputer,
A/D converter, etc.
IOUT: max. 200μA
Notes:
Digital output types:
The output signal for the digital output type is from inside FET drain, therefore pull-down resistors are necessary. Please select an output resistor (pull-down concept) in accordance with VOUT so that the output current is maximum 100μA. If the output current is more than 100μA, this may cause false alarms.
If the microcomputer has a pull-down function, there is no need for a resistor as long as the output current does not exceed 100µA.
Analog output types (EKMC26 series):
In either case, a microcomputer or a resistor needs to be chosen in accordance to VOUT, so that the output current is maximum 200µA.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
PIR MOTION SENSORS
07
EKM - Standard Detection Type
PaPIRs: 3rd generation
EKM series
Preference type
Flat lens for an unobtrusive integration
Lens diameter 9.5mm
Specified detection distance (Note 1)
up to 5m
Typical ceiling installation height (Note 2)
3m
Field of view
106° x 97°
Detection zones
64
Note 1:
Note 2:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
Typical applications
››
››
››
››
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
Lighting controls for offices and smart homes
Smart luminaires
Smart LED bulbs
IP cameras
Digital signage
Wake-up switch for
displays
Ventilation systems and
air conditioners
Dimension (in mm, inches in brackets)
AMN series
Further information on electrical characteristics please see page 16
Detection area
X-Y cross section at 3m (9.8ft)
Y
Y
5m
5m (16.4ft)
(16.4ft)
(48.4°)
41.8°
(0.374 dia.)
4m (13.1ft)
14.4
(0.567)
A
13
A
(0.512)
Ø9.5
Ø0.45
4.6
(0.181)
Ø11
(0.433 dia.)
VDD
P.C.D. Ø5.08 ±0.2
41.8°
(48.4°)
45
°
3m
OUT
±4°
45°
°
±4
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
1m
(3.3ft)
1m
(3.3ft)
2m
(6.6ft)
3m
(9.8ft)
5m
4m
3m
2m
1m
(16.4ft)
(13.1ft)
(9.8ft)
(6.6ft)
(3.3ft)
0
1m
2m
3m
(3.3ft)
(6.6ft)
(9.8ft)
4m
5m (16.4ft)
5m
(13.1ft) (16.4ft)
(9.8ft)
X
47.0°
(53.1°)
47.0°
(53.1°)
3m
(9.8ft)
5m
SECTION A-A
Notes
(6.6ft)
4m (13.1ft)
(0.2 dia.)
GND
(9.8ft)
2m
0
X
(0.018 dia.)
3m
(16.4ft)
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Sensitivity
White
Black
Pearl White
Standard
EKMB1101111
EKMB1101112
EKMB1101113
Standard
EKMB1201111
EKMB1201112
EKMB1201113
Standard
EKMB1301111K
EKMB1301112K
EKMB1301113K
Standard
EKMC1601111
EKMC1601112
EKMC1601113
Adjustable
EKMC2601111K
EKMC2601112K
EKMC2601113K
High
High
Please contact us if a higher or a lower sensitivity is required.
Low
Note: The specification shows the X-Y cross section at 2.5m.
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
08
PIR MOTION SENSORS
EKM - Low Profile Type
Lower height lens design
[14.4mmg10.9mm]
EKM series
Comparable performance to PaPIRs standard detection type lens
Fit with superior product design
Specified detection distance (Note 1)
up to 5m
Typical ceiling installation height (Note 2)
3m
Field of view
110° x 110°
Detection zones
32
Note 1:
Note 2:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
Typical applications
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
LED screen for TV, PC
››
››
Digital signage
Wake-up switch for
displays
››
››
Smart luminaires
››
IP cameras
Ventilation systems and
air conditioners
Lighting controls for
offices and smart home
AMN series
Further information on electrical characteristics please see page 16
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 3m (9.8ft)
Y
(16.4ft) 5m
Y
(54.8°)
5m(16.4ft)
44.7°
4m(13.1ft)
3m(9.8ft)
2m(6.6ft)
1m(3.3ft)
0
1m(3.3ft)
2m(6.6ft)
3m(9.8ft)
44.7°
4m(13.1ft)
(54.8°)
5m
4m
(16.4ft) (13.1ft)
3m
3m
(9.8ft)
2m
(6.6ft)
1m
(3.3ft)
0
1m
(3.3ft)
2m
(6.6ft)
3m
(9.8ft)
5m(16.4ft)
5m
4m
(13.1ft) (16.4ft)
(9.8ft)
44.7°
X
44.7°
(54.8°)
(54.8°)
3m
(9.8ft)
5m
(16.4ft)
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Sensitivity
White
Black
Pearl White
Standard
EKMB1107111
EKMB1107112
EKMB1107113
Standard
EKMB1207111
EKMB1207112
EKMB1207113
Standard
EKMB1307111K
EKMB1307112K
EKMB1307113K
Standard
EKMC1607111
EKMC1607112
EKMC1607113
Adjustable
EKMC2607111K
EKMC2607112K
EKMC2607113K
Note: The specification shows the X-Y cross section at 2.5m.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
High
High
Low
Please contact us if a higher or a lower sensitivity is required.
PIR MOTION SENSORS
09
EKM - Slight Motion Detection Type
Optimized for small movements
Lens diameter 14.6mm
Almost the same mechanical dimensions like the Standard and
Slight Motion Detection Type (lens diameter 0.3mm smaller)
up to 2.5m - 4m
Typical ceiling installation height (Note 2)
3m
Field of view
104° x 104°
Detection zones
112
Note 1:
Note 2:
›› ∆T ≥ 4°C
›› Object speed: 0.5m/s
›› Object size: 200 x 200mm
›› Crossing 1 detection zone
Typical applications
››
››
››
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
Lighting controls for
offices and smart
homes
Ventilation systems
and air conditioners
Smart luminaires
Smart LED bulbs
AMN series
Specified detection distance (Note 1)
Further information on electrical characteristics please see page 16
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 3m (9.8ft)
Y
Y
(52.2°)
48.5°
Molding gate
X
VDD
48.5°
(52.2°)
3m
OUT
(9.8ft)
5m
(16.4ft)
4m
(13.1ft)
3m
(9.8ft)
2m
(6.6ft)
1m
(3.3ft)
0
P.C.D.
GND
5m
4m
3m
2m
1m
(16.4ft)
(13.1ft)
(9.8ft)
(6.6ft)
(3.3ft)
0
1m
2m
3m
(3.3ft)
(6.6ft)
(9.8ft)
(52.2°) 48.5°
X
4m
1m
(3.3ft)
2m
(6.6ft)
3m
(9.8ft)
4m
(13.1ft)
5m
5m
(16.4ft)
(13.1ft) (16.4ft)
48.5°(52.2°)
3m
(9.8ft)
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
EKM series
PaPIRs: 3rd generation
Sensitivity
White
Black
Pearl White
Standard
EKMB1191111
EKMB1191112
EKMB1191113
Standard
EKMB1291111
EKMB1291112
EKMB1291113
Standard
EKMB1391111K
EKMB1391112K
EKMB1391113K
Standard
EKMC1691111
EKMC1691112
EKMC1691113
Adjustable
EKMC2691111K
EKMC2691112K
EKMC2691113K
High
High
Please contact us if a higher or a lower sensitivity is required.
Low
Note: The specification shows the X-Y cross section at 2.5m.
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
10
PIR MOTION SENSORS
010
EKM - Standard and Slight Motion Detection Type
PaPIRs: 3rd generation
EKM series
The rectangular center zone is optimized detecting smallest
movements.
Lens diameter 14.9mm
Almost the same mechanical dimensions like the Slight Motion
Detection Type (lens diameter 0.3mm bigger)
Specified detection distance (Note 1)
up to 2.2m - 3.1m
Typical ceiling installation height (Note 2)
3m
Field of view slight motion area
44° x 44°
Field of view standard motion area
91° x 91°
Detection zones slight motion area
36
Detection zones standard motion area
48
Note 1:
Note 2:
››
››
››
››
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
››
Lighting controls for
restrooms, changing
rooms, smoking cabins
and hotel rooms
Smart luminaires
Smart LED bulbs
Hot desking
Digital signage
Vending machines
Wake-up switch for
displays
Ventilation systems and
air conditioners
Further information on electrical characteristics please see page 16
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 3m (9.8ft)
Slight motion
detection area
Y
Standard motion
detection area
Y
5m (16.4ft)
16.6
(0.654 dia)
4m (13.1ft)
Ø14.9
(45.3°)
41.0°
3m (9.8ft)
2m (6.6ft)
17.2
(0.677)
7.9
A
A
Ø0.45 ±0.05
(0.311)
(0.587 dia)
1m (3.3ft)
X
(0.018 dia)
4.6
Ø11
0
(0.181)
AMN series
›› ∆T ≥ 4°C
›› Object speed: 0.5m/s (slight motion area)
›› Object speed: 1m/s (standard motion area)
›› Object size: 200 x 200mm (slight motion area)
›› Object size: 400 x 200mm (standard motion area)
›› Crossing 1 detection zone (slight motion area)
›› Crossing 2 detection zones (standard motion area)
Typical applications
(0.433 dia)
1m (3.3ft)
2m (6.6ft)
P.C.D. Ø5.08 ±0.2
VDD
(0.2 dia)
41.0°
(45.3°)
3m (9.8ft)
4m (13.1ft)
GND
OUT
3m
45
°
±4°
5m
(9.8ft)
4°
45° ±
(16.4ft)
4m
(13.1ft)
3m
2m
(9.8ft)
(6.6ft)
1m
(3.3ft)
0
1m
(3.3ft)
(45.3°) 41.0°
2m
(6.6ft)
3m
(9.8ft)
4m
5m (16.4ft)
5m
(13.1ft) (16.4ft)
41.0° (45.3°)
3m
X
(9.8ft)
SECTION A-A
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Note: The specification shows the X-Y cross section at 2.2m.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
Sensitivity
White
Black
Pearl White
Standard
EKMB1193111
EKMB1193112
EKMB1193113
Standard
EKMB1293111
EKMB1293112
EKMB1293113
Standard
EKMB1393111K
EKMB1393112K
EKMB1393113K
Standard
EKMC1693111
EKMC1693112
EKMC1693113
Adjustable
EKMC2693111K
EKMC2693112K
EKMC2693113K
High
High
Low
Please contact us if a higher or a lower sensitivity is required.
PIR MOTION SENSORS
11
EKM - High Density Long Distance Detection Type
PaPIRs: 3rd generation
EKM series
Smallest long range sensor
Maximum installation height of 17m (high sensitivity type)
Lens diameter 19.3mm
Maxim
insta um
llati
heigh on
t of
Additional lip (20.45mm) ready for an o-ring
up to 12m - 14.5m
Typical ceiling installation height (Note 2)
12m
Field of view
69° x 69°
Detection zones
128
Note 1:
Note 2:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
17m
Typical applications
››
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
Lighting controls for
warehouses, industrial
buildings, entrance halls
and retail shops
Street lighting
Security cameras
Smart high-bay
luminaires
AMN series
Specified detection distance (Note 1)
Further information on electrical characteristics please see page 16
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 12m (39.4ft)
Y
Y
10m (32.8ft)
(34.5°)
31°
X
(34.5°)
(39.4ft)
VVDDDD
(26.2ft)
6m
(19.7ft)
4m
(13.1ft)
2m
(6.6ft)
0
31°
12m
8m
10m 8m
6m
4m
2m
(32.8ft) (26.2ft)
(19.7ft)
(13.1ft)
(6.6ft)
0
(34.5°) 31°
X
2m
4m
(6.6ft)
(13.1ft) (19.7ft)
6m
8m
(26.2ft)
2m
(6.6ft)
4m
(13.1ft)
6m
(19.7ft)
8m
(26.2ft)
10m (32.8ft)
10m
(32.8ft)
31° (34.5°)
12m
(39.4ft)
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Sensitivity
White
Black
Pearl White
Standard
EKMB1106111
EKMB1106112
EKMB1106113
Standard
EKMB1206111
EKMB1206112
EKMB1206113
Standard
EKMB1306111K
EKMB1306112K
EKMB1306113K
Standard
EKMC1606111
EKMC1606112
EKMC1606113
Adjustable
EKMC2606111K
EKMC2606112K
EKMC2606113K
High
High
Please contact us if a higher or a lower sensitivity is required.
Low
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
12
PIR MOTION SENSORS
EKM - Horizontally Wide Detection Type
PaPIRs: 3rd generation
World’s first PIR with “Approach Sensing” technology
EKM series
Panasonic presents the world’s first PIR sensor in the shape of
a hammerhead with a special optic, which is more sensitive to
radial motion.
Specified detection distance (Note 1 & 2)
up to 5m
Field of view area A
122° x 35°
Field of view area B
150° x 20°
Detection zones area A
88
Detection zones area B
16
Note 2:
Note 1:
›› ∆T ≥ 4°C (Area A)
›› ∆T ≥ 8°C (Area B)
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
AMN series
Typical applications
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
››
Corridor sensors
››
››
Door intercom systems
Wall switches
Entrance and garden
lamps
››
Thermostats
Wake-up switch for
displays
Intrusion alarm sensors
for windows and doors
Further information on electrical characteristics please see page 16
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 1m (3.3ft)
Y
(10°)
Y
1m (3.3ft)
X
0
15°
4m
(13.1ft)
(25°)
3m
(9.8ft)
2m
(6.6ft)
1m
(3.3ft)
0
1m
(3.3ft)
2m
(6.6ft)
3m
(9.8ft)
1m (3.3ft)
4m
(13.1ft)
Area A
1m
(3.3ft)
(61°)
VDD
58°
58°
(61°)
Area B
Area B
(75°)
74°
74° (75°)
X
1m
(3.3ft)
5m
2.5m
(16.4ft)
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
(8.2ft)
Sensitivity
White
Black
Pearl White
Standard
EKMB1105111
EKMB1105112
EKMB1105113
Standard
EKMB1205111
EKMB1205112
EKMB1205113
Standard
EKMB1305111K
EKMB1305112K
EKMB1305113K
Standard
EKMC1605111
EKMC1605112
EKMC1605113
Adjustable
EKMC2605111K
EKMC2605112K
EKMC2605113K
High
High
Low
Please contact us if a higher or a lower sensitivity is required.
PIR MOTION SENSORS
13
EKM - Wall Installation Detection Type (corner)
PaPIRs: 3rd generation
EKM series
Lens diameter 20.7mm
Similar dimensions like the Long Distance Detection Type
Specified detection distance
(Note 1 & 2)
up to 12m (1st step lens)
up to 6m (2nd step lens)
up to 3m (3rd step lens)
Field of view
56° x 112°
Detection zones
68
Note 1:
Typical applications
››
››
››
››
Note 2:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
Intrusion alarm sensors
Thermostats
Door intercom systems
Entrance and garden
lamps
Dimension (in mm, inches in brackets)
AMN series
Further information on electrical characteristics please see page 16
Detection area
X-Y cross section at 5m (16.4ft)
Y
1st line lens
(0.866)
2m (6.6ft)
X
Ø20.7
0
1st step
2m (6.6ft)
2nd step
4.0°
(0.795)
3m
20.2
(9.8ft)
Ø11
2nd line lens
6m
8m
6m
(26.2ft) (19.7ft)
3rd line lens
4.6
(0.018 dia.)
4m(13.1ft)
(19.7ft)
(0.181)
Ø0.45 ±0.05
7.3
A
(0.287)
(0.815 dia.)
A
Y
(6.6°)
22
(0.433 dia.)
4m
(13.1ft)
2m
(6.6ft)
0
2m
(6.6ft)
4m
6m
(13.1ft) (19.7ft)
3rd step
6m(19.7ft)
8m
(26.2ft)
44.0°
(48.9°)
12m
GND
45
°
5m
(16.4ft)
5
(0.197)
2.5
(0.2 dia.)
(0.098)
(39.4ft)
VDD
P.C.D. Ø5.08 ±0.2
52.5°
(56.1°)
OUT
±4°
45°
52.5°
(56.1°)
5m
X
(16.4ft)
4°
±
12m
(39.4ft)
6m
(19.7ft)
3m
(9.8ft)
SECTION A-A
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Sensitivity
White
Black
Pearl White
Standard
EKMB1104111
EKMB1104112
EKMB1104113
Standard
EKMB1204111
EKMB1204112
EKMB1204113
Standard
EKMB1304111K
EKMB1304112K
EKMB1304113K
Standard
EKMC1604111
EKMC1604112
EKMC1604113
Adjustable
EKMC2604111K
EKMC2604112K
EKMC2604113K
High
High
Please contact us if a higher or a lower sensitivity is required.
Low
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
14
PIR MOTION SENSORS
EKM - Long Distance Detection Type
PaPIRs: 3rd generation
Lens diameter 20.7mm
EKM series
Similar dimensions like the Wall Installation Type
Specified detection distance (Note 1)
up to 12m
Typical ceiling installation height (Note 2)
7m
Field of view
108° x 99°
Detection zones
92
Typical applications
››
››
››
››
Note 2:
Note 1:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
The sensitivity of passive infrared
sensors is influenced by environmental conditions, so a performance
evaluation test under representative
conditions is recommended
Lighting control for
sport halls and public
areas
Intrusion alarm sensors
Street lighting
Security cameras
Dimension (in mm, inches in brackets)
Detection area
12m
Y
X-Y cross section at 7m (22.9ft)
(39.4ft)
Y
(49.3°)
46.3°
10m (32.8ft)
22
(0.866)
Ø20.7
P.C.D. Ø5.08±0.2
(0.2 dia.)
20.2
5
VDD
2.5
Ø11
(0.433 dia.)
(0.197)
4.6
(0.018 dia.)
46.3°
(49.3°)
10m 8m
6m
(32.8ft) (26.2ft) (19.7ft)
GND
°±4°
(26.2ft)
6m
(19.7ft)
4m
(13.1ft)
2m
(6.6ft)
4m
2m
(13.1ft)
(6.6ft)
0
2m
4m
(6.6ft)
(13.1ft)
6m
2m
(6.6ft)
4m
(13.1ft)
6m
(19.7ft)
8m
(26.2ft)
10m (32.8ft)
8m 10m
(19.7ft) (26.2ft) (32.8ft)
7m
OUT
45
8m
0
X
(0.181)
Ø0.45 ±0.05
(0.795)
A
7.3
A
(0.287)
(0.815 dia.)
(0.098)
AMN series
Further information on electrical characteristics please see page 16
(23.0ft)
4°
45°±
X
51.3°
(54.0°)
51.3°
(54.0°)
7m
(23.0ft)
SECTION A-A
12m
(39.4ft)
Notes
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Note: The specification shows the X-Y cross section at 5m.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
Sensitivity
White
Black
Pearl White
Standard
EKMB1103111
EKMB1103112
EKMB1103113
Standard
EKMB1203111
EKMB1203112
EKMB1203113
Standard
EKMB1303111K
EKMB1303112K
EKMB1303113K
Standard
EKMC1603111
EKMC1603112
EKMC1603113
Adjustable
EKMC2603111K
EKMC2603112K
EKMC2603113K
High
High
Low
Please contact us if a higher or a lower sensitivity is required.
PIR MOTION SENSORS
15
EKM - Lensless Type
Small sensor elements with a very high sensitivity (D, NEP)
Please contact us whenever a customized lens is required, the
sensor shall be used with an external lens or for the design
data of the pin-hole lens
Typical applications
Average: 5.6μW/cm²
Maximum: 7.6μW/cm²
Detection sensitivity
››
››
Detection sensitivity is measured by following system
Black body
250° C
Aperture
Masking
plate
EKM series
PaPIRs: 3rd generation
PaPIRs
Pin-hole lens
Combination with
lenses from external
suppliers
5V DC
340mm
Recorder
Chopper (1Hz )
Dimension (in mm, inches in brackets)
AMN series
Further information on electrical characteristics please see page 16
Detection area
Pin-hole lens example
3.0
0.6
3.0
0.4
Ø9.1
Ø8.3
55°
0.6
ELEMENT
0.6
8.4
9.3
Ø0.45 ±0.05
5.5
P.C.
D
0.6
0.4
VDD
.Ø
5.08 ±0
.2
GND
45° ±
4°
Notes
OUT
45°
±4°
Standby current
consumption
1µA
High-end
2µA
6µA
Economy
170µA
170µA
6µA
Special
170µA
170µA
Output type
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Analog
(op amp)
Digital
(open collector)
Digital
(open collector)
Digital
(open collector)
Sensitivity
Part numbers
Standard
EKMB1100100
Standard
EKMB1200100
Standard
EKMB1300100K
Standard
EKMC1600100
Adjustable
EKMC2600100K
High
High
Please contact us if a higher or a lower sensitivity is required.
Low
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
16
PIR MOTION SENSORS
EKM - Characteristics
EKM series
EKM - Maximum rated values
Items
EKMB series
EKMC series
Power supply voltage
-0.3 to 4.5V DC
-0.3 to 7V DC
Ambient temperature
-20 to 60°C
-20 to 55°C (high sensitivity type)
(no frost, no condensation)
Storage temperature
-20 to 70°C
EKM - Electrical characteristics (digital output types)
Item
AMN series
Operating voltage
Symbol
VDD
EKMB11 series
(1μA)
EKMB12 series
(2μA)
EKMB13K series
(6μA)
EKMC16 series
(170µA)
Max
4.0V DC
6.0V DC
Min
2.3V DC
3.0V DC
Conditions
–
Ambient temperature: 25°C
IOUT = 0A
EKMB series: VDD = 3V DC
EKMC series: VDD = 5V DC
Current consumption
(in standby/sleep mode)
Note 1
IW
Ave
Output current
(during detection period)
Note 2
IOUT
Max
100μA
Ambient temperature: 25°C
VOUT ≥ VDD – 0.5V DC
Output voltage
(during detection period)
VOUT
Min
VDD – 0.5V
Ambient temperature: 25°C
Circuit stability time
(when voltage is applied)
tWU
1μA
2μA
6μA
170µA
Ave
25 seconds
–
–
Max
210 seconds
10 seconds
30 seconds
Ambient temperature: 25°C
IOUT = 0A
EKMB series: VDD = 3V DC
EKMC series: VDD = 5V DC
Note 1:
The total current consumption during detection is the current consumption in standby mode (IW) plus the output current (IOUT). For the 1μA type the average current consumption (IW) is 1μA in sleep mode and 1.9μA in standby mode. Please also refer to the timing charts on the next page.
Note 2:
Please select an output resistor (pull-down concept) in accordance with VOUT so that the output current is maximum 100μA.
EKM - Electrical characteristics (analog output)
Item
Symbol
Operating voltage
VDD
Current consumption
(in standby mode) Note1
IW
Output current
(during detection period) Note 2
Analog output saturated voltage
Output offset voltage
(at non detection)
Remarks
EKMC26K series
Max
5.5V
Min
3.0V
Ave
170μA
Max
350μA
Ambient temperature = 25°C
IOUT = 0A
IOUT
Max
200μA
–
VH
High
Min. 1.9V
–
VL
Low
Max. 0.2V
–
Max
1.2V
Ave
1.1V
Min
1.0V
Max
150mVPP
Ave
80mVPP
Max
30 seconds
VOFF
Steady noise
VN
Circuit stability time
(after applying voltage)
tWU
–
Ambient temperature: 25°C
Steady output voltage at non
detection
–
Ambient temperature: 25°C
IOUT = 0A
Note 1:
The total current consumption during detection is the current consumption in standby mode (IW) plus the output current (IOUT).
Note 2:
The output offset voltage has a certain tolerance. Please assure to measure the offset voltage before setting the upper and lower threshold values.
Otherwise the threshold window could be unsymmetrical relative to the offset voltage.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
PIR MOTION SENSORS
17
Timing chart
1μA type (digital output)
EKM series
2μA / 6μA / 170μA type (digital output)
ON
ON
Power supply
Power supply
OFF
OFF
Yes
Yes
Movement
Movement
No
No
High
1) Sleep
2) Standby
3) Mask
Mode
Output
Low
tWU
Unstable
1）
2）
3） 1）
2）
3）
1）
2）
3）
High
Output
Low
t2
t3
t2
t2
t3
*2
Explanation of the timing
tWU
*1
Explanation of modes
Circuit stability time: about 25 seconds (typ.) for 2μA type,
max. 10 seconds for 6μA type, max. 30 seconds for 170μA type.
1)
Sleep mode:
When the output is Low. The electrical current consumption is around
1μA
While the circuitry is stabilizing after the power is turned on, the
sensor output is not fixed in the High or Low state. This is true
regardless of whether or not the sensor has detected anything.
2)
Standby mode:
After the sensor's output has reached High status, the sensor switches
to standby mode. The electrical current consumption gets close to
1.9μA. When the sensor's output returns to its Low value after the "hold
time" has expired, the sensor switches again to sleep mode.
3)
Mask mode:
Time during which the output is forced to Low status after the end of the
standby mode. (No detection is possible during this period.)
Explanation of the timing
t1)
(tWU)
Circuit stability time: about 25 seconds (typ.)
While the circuitry is stabilizing after the power is turned on, the sensor
output is not fixed in the High or Low state. This is true regardless of
whether or not the sensor has detected anything.
t2)
Standby hold time:
About 2.6 seconds (typ.) after the last detection of a signal. (*1)
t3)
Mask time:
About 1.3 seconds (typ.) During this stage, even if the sensor detects
something, the output will not switch to High. (*2)
170μA type (analog output)
ON
Power supply
OFF
Movement
Yes
No
VDD
VH
Output voltage
GND
tWU
VOFF
VN
VL
Detection signal
Explanation of the timing
tWU
Circuit stability time: max. 30 seconds
While the circuitry is stabilizing after the power is turned on, the sensor output
is not fixed. This is true regardless of whether or not the sensor has detected
anything.
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
AMN series
t1（tWU）
18
PIR MOTION SENSORS
AMN - Standard Detection Type
NaPiOn: 2nd generation
EKM series
Small lens diameter of only 9.5mm
Specified detection distance (Note 1)
up to 5m
Typical ceiling installation height (Note 2)
3m
Field of view
120° x 106°
Detection zones
64
Note 2:
Note 1:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
Lighting controls
››
Multi-functional printers
Heaters
Ventilators and air
conditioners
Further information on electrical characteristics please see page 22
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 3m (9.8ft)
Y
5m
(0.374 dia.)
5m (16.4ft)
(53.1°)
44.8°
14.5
4.5
(0.177)
(0.018 dia.)
Ø11
(0.433 dia.)
4m (13.1ft)
(0.571)
11
A
A
Ø0.45 ±0.05
6m (19.9ft)
Y
(16.4ft)
9.5
(0.433)
AMN series
Typical applications
X
(0.2 dia.)
44.8°
(53.1°)
GND
45
°
45°
(6.6ft)
1m
(3.3ft)
1m
(3.3ft)
2m
(6.6ft)
3m
(9.8ft)
4m (13.1ft)
OUT
±4°
(9.8ft)
2m
0
VDD
P.C.D. Ø5.08 ±0.2
3m
5m (16.4ft)
4°
6m
5m
4m
3m
2m
1m
(19.9ft)
(16.4ft)
(13.1ft)
(9.8ft)
(6.6ft)
(3.3ft)
0
1m
2m
3m
4m
5m
(3.3ft)
(6.6ft)
(9.8ft)
(13.1ft)
(16.4ft)
6m (19.9ft)
6m
(19.9ft)
±
54.0°
X
(60.1°)
SECTION A-A
54.0°
(60.1°)
5m
(16.4ft)
Notes
Standby current consumption
Output type
Sensitivity
White
Black
NaPiOn 2nd generation
170μA
Digital
(open collector)
Standard
AMN31112
AMN31111
Note: The specification shows the X-Y cross section at 2.5m.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
PIR MOTION SENSORS
19
AMN - Slight Motion Detection Type
NaPiOn: 2nd generation
EKM series
Optimized for small movements
Specified detection distance (Note 1)
up to 2m - 3.3m
Typical ceiling installation height (Note 2)
3m
Field of view
107° x 106°
Detection zones
104
Typical applications
Note 2:
Note 1:
›› ∆T ≥ 4°C
›› Object speed: 0.5m/s
›› Object size: 200mm x 200mm
›› Crossing 1 detection zone
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
Lighting controls
››
Multi-functional printers
Heaters
Ventilators and air
conditioners
Dimension (in mm, inches in brackets)
AMN series
Further information on electrical characteristics please see page 22
Detection area
X-Y cross section at 3m (9.8ft)
Y
Ø12.7
Y
(53.6°)
(0.500 dia.)
Ø11.9
49.0°
5m
(16.4ft)
4m
(13.1ft)
3m
(9.8ft)
15.2
(0.598)
12.8
(0.504)
2m (6.6ft)
1m (3.3ft)
(0.177)
(0.018 dia.)
8.9
A
A
Ø0.45 ±0.05
(0.350)
(0.469 dia.)
X
4.5
Ø11
(0.433 dia.)
0
1m (3.3ft)
VDD
P.C.D. Ø5.08 ±0.2
(0.2 dia.)
49.0°
3m
GND
OUT
5m
4m
(16.4ft) (13.1ft)
3m
(9.8ft)
2m
(6.6ft)
1m
(3.3ft)
(53.1°) 48.3°
X
45
°
±4°
45°
SECTION
(6.6ft)
3m
(9.8ft)
4m (13.1ft)
(53.6°)
(9.8ft)
2m
0
1m
(3.3ft)
2m
(6.6ft)
3m
(9.8ft)
4m
5m (16.4ft)
5m
(13.1ft) (16.4ft)
48.3°(53.1°)
3m (9.8ft)
°
±4
A-A
Notes
Standby current consumption
Output type
Sensitivity
White
Black
NaPiOn 2nd generation
170μA
Digital
(open collector)
Standard
AMN32112
AMN32111
Note: The specification shows the X-Y cross section at 2m.
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
20
PIR MOTION SENSORS
AMN - Spot Detection Type
NaPiOn: 2nd generation
Flat lens
EKM series
Lens diameter 8.9mm
Narrow field of view
Specified detection distance (Note 1)
up to 5m - 5.6m
Typical ceiling installation height (Note 2)
5m
Field of view
57° x 42°
Detection zones
24
Note 2:
Note 1:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
››
››
››
Vending machines
››
Digital signage
Multi-functional printers
Intrusion alarm sensors
for windows and doors
Further information on electrical characteristics please see pag 22
Dimension (in mm, inches in brackets)
Detection area
X-Y cross section at 5m (16.4ft)
Y
(0.350 dia.)
Ø8.9
3m (9.8ft)
15.1
A
2m (6.6ft)
1m (3.3ft)
(0.594)
A
Y
(28.5°)
20.2°
X
0
Ø0.45 ±0.05
(0.018 dia.)
1m (3.3ft)
4.5
(0.177)
AMN series
Typical applications
Ø11
(0.433 dia.)
2m (6.6ft)
20.2°
5m
(28.5°)
(16.4ft)
3m
(9.8ft)
VDD
P.C.D. Ø5.08 ±0.2
(0.2 dia.)
2m
(6.6ft)
1m
(3.3ft)
(21.0°) 11.9°
0
1m
(3.3ft)
2m
(6.6ft)
11.9° (21.0°)
5m
X
GND
45
°
(16.4ft)
OUT
±4°
45°
°
±4
SECTION A-A
Notes
Standby current consumption
Output type
Sensitivity
White
Black
NaPiOn 2nd generation
170μA
Digital
(open collector)
Standard
AMN33112
AMN33111
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
3m (9.8ft)
3m
(9.8ft)
PIR MOTION SENSORS
21
AMN - 10m Detection Type (long distance)
EKM series
NaPiOn: 2nd generation
Specified detection distance (Note 1)
up to 5 - 10m
Typical ceiling installation height (Note 2)
5m
Field of view
120° x 107°
Detection zones
80
Note 1:
Typical applications
››
››
››
Note 2:
›› ∆T ≥ 4°C
›› Object speed: 1m/s
›› Object size: 700 x 250mm
›› Crossing 2 detection zones
The sensitivity of passive infrared
sensors is influenced by environmental
conditions, so a performance evaluation
test under representative conditions is
recommended
Lighting controls
Heaters
Ventilators and
air-conditioners
Dimension (in mm, inches in brackets)
AMN series
Further information on electrical characteristics please see page 22
Detection area
X-Y cross section at 5m (16.4ft)
Y
10m
(32.8ft)
Y
(60.0°)
57.1°
Ø17.4
(0.685 dia.)
Ø17
18.5
4.5
Ø11
(0.433 dia.)
VDD
P.C.D. Ø5.08 ±0.2
57.1°
(60.0°)
(0.2 dia.)
10m
5m
(32.8ft)
(32.8ft)
8m
(26.2ft)
6m
(19.7ft)
4m
(13.1ft)
2m
(6.6ft)
0
X
(0.177)
(0.018 dia.)
(0.730)
A
8.6
A
Ø0.45 ±0.05
(0.339)
(0.669 dia.)
10m
8m
6m
4m
(26.2ft) (19.7ft) (13.1ft)
2m
(6.6ft)
0
2m
(6.6ft)
4m
6m
(13.1ft) (19.7ft)
8m
(26.2ft)
2m
(6.6ft)
4m
(13.1ft)
6m
(19.7ft)
8m
(26.2ft)
10m (32.8ft)
10m
(32.8ft)
(16.4ft)
GND
45
°
OUT
±4°
45°
49.3°
(53.5°)
°
±4
49.3°
(53.5°)
X
5m
(16.4ft)
10m
(32.8ft)
SECTION A-A
Notes
Standby current consumption
Output type
Sensitivity
White
Black
NaPiOn 2nd generation
170μA
Digital
(open collector)
Standard
AMN34112
AMN34111
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
22
PIR MOTION SENSORS
AMN - Characteristics
EKM series
AMN - Maximum rated values (digital output)
Items
Value
Power supply voltage
-0.3 to 7V DC
Ambient temperature
-20 to +60°C
(no frost, no condensation)
Storage temperature
-20 to +70°C
AMN - Electrical characteristics (digital output)
Symbol
Operating voltage
VDD
Current consumption (in standby mode)
Note 1
AMN series
Items
AMN3* series
Conditions
Max
6.0V DC
Min
3.0V DC
IW
Ave
170μA
Ambient temperature: 25°C
IOUT = 0A VDD = 5V DC
Output current (during detection)
Note 2
IOUT
Max
100μA
Ambient temperature: 25°C
VOUT ≥ VDD – 0.5V DC
Output voltage (during detection)
VOUT
Min
VDD - 0.5V
Ambient temperature: 25°C
Circuit stability time
(when voltage is applied) Note 3
tWU
Max
30 seconds
Ambient temperature: 25°C
IOUT = 0A VDD = 5V DC
–
Note 1:
The total current consumption is equal to the current consumption in standby mode (IW) plus the output current (IOUT).
Note 2:
Please select an output resistor (pull-down concept) in accordance with VOUT so that the output current is maximum 100μA. If the output current is more than 100μA, this
may cause false alarms.
Note 3:
The sensor temperature has to be constant for the time specified.
Digital output
ON
Power supply
OFF
Yes
Movement
No
High
Output
Low
tWU
Explanation of the timing
tWU
Circuit stability time: max. 30 seconds
While the circuitry is stabilizing after the power is turned on, the sensor output
is not fixed in the High or Low state. This is true regardless of whether or not the
sensor has detected anything.
Further information at www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
PIR MOTION SENSORS
23
Cautions for use
Basic principles
Cautions
PaPIRs are pyroelectric infrared sensors that detect variations in infrared rays.
However, detection may not be successful in the following cases: lack of movement or no
temperature change in the heat source. They could also detect the presence of heat sources other than a human body. Efficiency and reliability of the system may vary depending on
the actual operating conditions:
1) Refer to the newest specification regarding optimal operating environment conditions.
2) Do not solder with a soldering iron above 350°C (662°F) or for more than 3 seconds.
This sensor should be hand-soldered.
3) To maintain stability of the product, always mount it on a printed circuit board.
4) Do not use liquids to wash the sensor. If washing fluid gets into the lens, it can reduce
the performance.
5) Do not use a sensor after it has fallen on the ground.
6) The sensor may be damaged by ±200 volts of static electricity.
Avoid direct hand contact with the pins and be very careful when operating the product.
7) When wiring the product, always use shielded cables and minimize the wiring length to
prevent noise disturbances.
8) The inner circuit board can be destroyed by a voltage surge.
The use of surge absorption elements is highly recommended.
Surge resistance: below the power supply voltage value indicated in the section on
maximum rated values.
9) Please use a stabilized power supply. Noise from the power supply can cause operating errors.
Noise resistance: max. ±20V (square waves with a width of 50ns or 1μs)
To reduce the effect of noise from the power supply , install a capacitor on the sensor's
power supply pin.
10) Operation errors can be caused by noise from static electricity, lightnings, cell phones,
amateur radio, broadcasting offices, etc
11) The detection performance can be reduced by dirt on the lens, please be careful.
12) The lens is made of soft materials (Polyethylene).
Please avoid adding weight or impacts that may change its shape, causing operation
errors or reduced performance.
13) The specified temperature and humidity levels are suggested to prolong usage. However, they do not guarantee durability or environmental resistance.
Generally, high temperatures or high humidity levels will accelerate the deterioration of
electrical components. Please consider both the planned usage and environment to
determine the expected reliability and length of life of the product.
14) Do not attempt to clean this product with detergents or solvents such as benzene or
alcohol, as these can cause shape or color alterations.
15) Avoid storage in high, low temperature or liquid environments.
Also, avoid storage in environments containing corrosive gas, dust, salty air etc.
Adverse conditions may cause performance deterioration and the sensor's main part or
the metallic connectors could be damaged.
16) Storage conditions
Temperature: +5 to +40°C, humidity: 30 to 75%
Please use within 1 year after delivery.
1) Detecting heat sources other than the human body, such as:
a) small animals entering the detection area
b) When a heat source, for example sun light, incandescent lamp, car headlights etc.,
or strong light beam hit the sensor regardless whether the detection area is inside
or outside.
c) Sudden temperature change inside or around the detection area caused by hot
or cold wind from HVAC, or vapor from a humidifier, etc.
2) Difficulty in sensing the heat source
a) Glass, acrylic or similar materials standing between the target and the sensor may
not allow a correct transmission of infrared rays.
b) Non-movement or quick movements of the heat source inside the detection area.
(Please refer to the table on page 8 or 11 for details about movement speed.)
3) Expansion of the detection area
In case of a considerable difference in the ambient temperature and the human body
temperature, the detection area may be larger than the configured detection area.
4) Malfunction / Detection error
On rare occasions, an erroneous detection signal may be output due to the nature of
pyroelectric element. When the application cannot tolerate erroneous detection signals,
take countermeasures by introducing a pulse-count circuit, etc.
5) Detection distance
Panasonic's PIR Motion sensors state the detection distance in the specifications
because they are usually provided with the lens (please refer to item 6 for lensless
types). The PIR Motion sensor could detect variations in infrared rays however such
variations are decided by following three factors.
• The temperature difference between the target and the surroundings:
The larger the temperature difference, the easier it is to detect targets.
•
Movement speed: If the target is moving at a slower or faster speed than specified in
the tables, the detection ability may be lower.
• Target size: The human body is the standard. If the target is smaller or larger than
specified in the table, the detection ability may be lower.
The detection distance explained in our data sheet is defined by the three factors
mentioned above. Panasonic's standard for the temperature difference between the
target and the surrounding is defined as 4°C. The larger the temperature difference,
the longer the detection distance. If the temperature difference is 8°C, which is twice
as much as the standard, the detection distance will be approx. 1.4 times longer than
the distance at 4°C. For example, if targets at a distance of 5m can be detected at
4°C, then the sensor can detect targets at a distance of 7m at 8°C. (This is based
on the theory that the detection sensitivity will vary inversely with the square of the
distance.)
6) Lensless Type
The lensless type cannot detect any targets because it is not possible to focus infrared
variations into the sensor chip. It is not possible to determine the detection distance and
the field of view without a lens. Please provide your own lens based on your lens design
concept.
7) Lens material and the plate setting in front of the lens
Typically, the only material that can be passed by infrared rays is Polyethylene.
(The lens material of Panasonic's PIR Motion sensors is "High density polyethylene,
HDPE".) When you need to set a plate in front of the lens, please choose one made from
the Polyethylene. Please note the thickness or color of the plate will affect the detection
ability, e.g. it may make the detection distance shorter. Therefore, please confirm by
testing the sensor with the plate under realistic conditions.
Safety precautions
Obey the following precautions to prevent injury or accidents.
1) Do not use these sensors under any circumstance in which the range of their ratings, environment conditions or other specifications are exceeded. Using the sensors in any way
which causes their specifications to be exceeded may generate abnormally high levels of heat, emit smoke, etc., resulting in damage to the circuitry and possibly causing an
accident.
2) Our company is committed to making products of the highest quality and reliability. Nevertheless, all electrical components are subject to natural deterioration, and durability of a
product will depend on the operating environment and conditions of use. Continued use after such deterioration could lead to overheating, smoke or fire. Always use the product in
conjunction with proper fire-prevention, safety and maintenance measures to avoid accidents, reduction in product life expectancy or break-down.
3) Before connecting, check the pin layout by referring to the connector wiring diagram, specifications diagram, etc., to verify that the connector is connected properly. Mistakes
made in connection may cause unforeseen problems in operation, generate abnormally high levels of heat, emit smoke, etc., resulting in damage to the circuitry.
4) Do not use any motion sensor which has been disassembled or remodeled.
5) Failure modes of sensors include short-circuiting, open-circuiting and temperature rises. If this sensor is to be used in equipment where safety is a prime consideration, examine the possible effects of these failures on the equipment concerned, and ensure safety by providing protection circuits or protection devices.
Example : Safety equipment and devices, traffic signals, burglar and disaster prevention devices, controlling and safety device for trains and motor vehicles
Further information at /www3.panasonic.biz/ac/e/control/sensor/human/index.jsp
Global Network
Europe
East Asia
Germany
(European Headquarters) : Panasonic Electric Works Europe AG
Austria :
Panasonic Electric Works Austria GmbH
Panasonic Industrial Devices Materials Europe GmbH
Benelux :
Panasonic Electric Works Sales Western Europe B.V.
Czech Republic : Panasonic Electric Works Europe AG, organizac�ní složka
France :
Panasonic Electric Works Sales Western Europe B.V.
Hungary :
Panasonic Electric Works Europe AG
Ireland :
Panasonic Electric Works UK Ltd.
Italy :
Panasonic Electric Works Italia srl
Nordic Countries : Panasonic Electric Works Europe AG
Panasonic Fire & Security Europe AB
Poland :
Panasonic Electric Works Polska sp. z o.o.
Spain :
Panasonic Electric Works España S.A.
Switzerland :
Panasonic Electric Works Schweiz AG
United Kingdom : Panasonic Electric Works UK Ltd.
China :
Panasonic Industrial Device Sales (China) Co., Ltd.
Hong Kong :
Panasonic Industrial Devices Sales (Hong Kong) Co., Ltd.
Taiwan :
Panasonic Industrial Devices Sales Taiwan Co., Ltd.
Korea :
Panasonic Industrial Devices Sales Korea Co., Ltd.
Japan :
Panasonic Industrial Devices Sales Japan Co., Ltd.
Asia-Pacific
SINGAPORE /
INDONESIA :
Panasonic Industrial Devices Automation Controls Sales Asia Pacific
THAILAND :
Panasonic Life Solutions Sales (Thailand )Co.,Ltd.
MALAYSIA :
Panasonic Industrial Devices Sales (M) Sdn. Bhd.
PHILIPPINES :
Panasonic Philippines (Sales Division of PMPC)
INDIA :
Panasonic India Pvt. Ltd. / Industrial Division
VIETNAM :
Panasonic Vietnam Co., Ltd. / Panasonic Sales Vietnam
TURKEY :
Panasonic Elektronik Satis A.S. PTR.
The Americas
United States
(Headquarters in NJ) : Panasonic Industrial Devices Sales Company of America
Canada :
Panasonic Canada Inc
Brazil :
Panasonic Do Brasil Limitada
ロㄊㄇㄆチヴㄐㄍㄖㄕㄊㄐㄏㄔチヤㄐㄎㄑㄏㄚ
System Components Business Unit
Address: 1048, Kadoma, Kadoma-shi
Osaka 571-8686, Japan
Telephone: +81-6-6900-2773
(Sensors & Devices Promotion Department)
Web: http://www3.panasonic.biz/ac/e/control/sensor/human/
(PIR Motion Sensor PaPIRs)
All Rights Reserved © 2019 COPYRIGHT Panasonic Corporation
Specifications are subject to change without notice.
工商网监
湘ICP备2023018690号
