ER-XC02

1159 FIBER SENSORS Area Ionizer Pulse AC Method ER-X SERIES Related Information ■■General terms and conditions.............. F-7 ■■Glossary of terms.......................... P.1497 ■■Selection guide............................ P.1157~ ■■General precautions...................... P.1501 LASER SENSORS PHOTOELECTRIC SENSORS Conforming to EMC Directive MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS panasonic.net/id/pidsx/global MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS High-Speed, Wide Area Charge Removal "Fast Charge Removal", "Airless", "Low-Pressure". Three charge removal modes for diverse application coverage. The ER-X series offers an airless charge removal capability to eliminate the need for compressed air in addition to low pressure and high speed compressed air based modes. Furthermore, it supports dual-head configurations for expanded application coverage. MACHINE VISION SYSTEMS UV CURING SYSTEMS Head 1 Head 2 Selection Guide Static Removers Cleaning Box Pulse Air-gun Electrostatic Sensor ER-X ER-TF Fast Charge Removal Airless or LowPressure ER-VS02 ER-VW ER-Q ER-F Massive ion discharge when using air reduces charge removal time. Prevents dust dispersion and cleanliness degradation! By applying a compressed air source, the ion volume increases providing an improved tact time for substrate ionization. This makes the ER-X suitable for applications such as electronic paper and thin film solar cells, where charge removal time is directly linked to productivity. The ER-X series can effectively remove surface charges with an air pressure of less than 0.05 MPa. With the advantage of minimal dust dispersion, it is suitable for charge removal in semiconductor, FPD (mobile panel), and other applications that require high degree of cleanliness. The presence of air also helps prevent adhesion of dust to the discharge needles, requiring less cleaning than in the airless charge removal mode. Area Ionizer ER-X SERIES APPLICATIONS 1160 FIBER SENSORS Removal of static charges on laminate film Prevention of part feeder clogging High-speed charge removal on FPCs LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Removing dust while separating TAB protective film PARTICULAR USE SENSORS Preventing static damage to module components SENSOR OPTIONS ER-X008 SIMPLE WIRE-SAVING UNITS ER-X008 WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC Super-compact slim head Pulse AC method for faster charge removal By thoroughly redesigning the discharge needle, we have created a super-compact slim head that combines high-speed charge removal*1 with a maintenance-saving design*2. The ER-X series can be embedded in, or retrofitted onto, equipment that did not provide enough space for antistatic measures in the past. The ER-X series has adopted the pulse AC method that alternately applies positive and negative voltages to each discharge needle. This enables generation and discharge of a large amount of ions, resulting in faster charge removal. Select from eight pulse frequencies according to your application, from 100 Hz for charge removal on nearby or moving workpieces to 1 Hz for charge removal on far-away workpieces or in a threedimensional space. *1 Pulse AC method with built-in air tubes (max. pressure 0.5 MPa) *2 Discharge needle air barrier structure, discharge needle unit for simple need replacement HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Charge removal time characteristics (TYPICAL) 30 mm (1.181 in) 22 mm (0.866 in) Measured at a charge removal distance of 100 mm 3.937 in using a 150 × 150 mm 5.906 × 5.906 in CPM (at center of CPM). 1,000 Charge voltage (V) Angle adjustment screw 360degree angle adjustment − Conventional type, with airflow, 0.05 MPa − ER-X032, airless − ER-X032, with airflow, 0.05 MPa 800 Cleaning Box Pulse Air-gun 600 Electrostatic Sensor Conventional type 400 200 Selection Guide Static Removers ER-X ER-X ER-TF 0 1 2 3 Charge removal time (sec.) 4 ER-VS02 ER-VW ER-Q ER-F 1161 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS Area Ionizer ER-X SERIES Automatic ion balance control Discharge needle air barrier design for reduced contamination The ER-X series provides an automatic ion balance control mechanism that senses the amount of ions being generated (which changes according to environmental factors) and compensate for this deviation in the controller, thus maintaining a highly stable ion balance as an original operator setting. A barrier of clean air around the discharge needle keeps foreign matter from adhering to it, preventing degraded performance. Additionally, by using separate air sources for the discharge needle barrier and ion transport, the ER-X series keeps discharge from becoming unstable due to pressure concentration, allowing the device to efficiently generate and transport ions. Example of variable discharge frequency/ion balance LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC Air barrier structure Efficient charge removal structure using 0.05 MPa airflow Discharge needle after 1 month Efficient charge removal structure Variable discharge frequency Variable ion balance Carefully designed to prevent contamination in manufacturing processes In consideration of the manufacturing process (secondary cells etc.), the ER-X series heads neither use copper nor plate processing. This minimizes the risk of contamination with foreign substances. Flat discharge surface for easy cleaning Discharge needle unit for simple needle replacement The ER-X series heads have a flat discharge face, allowing effortless cleaning of the discharge needles and air outlets by simply brushing along the groove provided. The removable discharge needle unit (including a set of four needles) substantially simplifies maintenance. To remove the unit, just slide it toward both ends as indicated by the arrows. HUMAN MACHINE INTERFACES Discharge needles ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS Air outlets Discharge needle unit UV CURING SYSTEMS Groove Selection Guide Static Removers Commercial brush Dual Head Configuration for Enhanced Charge Area and Layout Expansion Cleaning Box 1 Controller Pulse Air-gun controller Electrostatic Sensor • Different heads can be combined. • Charge removal is possible with a layout that places heads on either side of the workpiece. • The charge removal efficiency can be increased by synchronizing the two heads. High-voltage unit ER-X ER-TF ER-VS02 ER-VW Head 1 + 2 heads High-voltage unit ER-Q ER-F Head 2 Charge removal modes can be selected. Charge removal in "fast" or "low-pressure" mode requires compressed air, while "airless or low-pressure" mode does not need compressed air. Area Ionizer ER-X SERIES Multifunction controller to which 2 heads can be connected FIBER SENSORS This all-in-one model controller features a range of functionality that allows it to perform optimal charge removal. Level meter indicator (green) Indicates static buildup around the head or the amount of ion generated from the head. Discharge indicator (green) Lights up during discharge. CHECK indicator (orange) Lights up when dirt, wear, etc. of the discharge needle is detected. ERROR indicator (red) Lights up when abnormal discharge is detected. Discharge frequency setting switch Discharge control switch ON: Discharge allowed OFF: Discharge halt SET UP button Stores the settings for the amount of ion and the check threshold in memory. Discharge control input Turn ion generation on and off from an external device. Alarm output, error output Report maintenance timing and malfunctions to an external device. 1162 Select from eight ion generation frequencies ranging from 100 Hz to 1 Hz according to your application. Ion balance setting switch Adjust the ion balance to any of 15 levels according to the strength of the charge on the workpieces. Various setting switch • Check level changeover switch Set the maintenance notification level to “standard” or “high-sensitivity.” • Ion balance control switch Enable or disable the ion balance auto control function. • Indicator changeover switch Set the level meter indicator display mode to “charge strength display” or “ion generation volume display.” • 2 heads control switch Set the ion generation timing for the two heads to “synchronize” or “inverse.” LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Static Removers Cleaning Box Pulse Air-gun Electrostatic Sensor ER-X ER-TF ER-VS02 ER-VW ER-Q ER-F 1163 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Area Ionizer ER-X SERIES ORDER GUIDE Heads Head connection cable is not supplied with the head. Please order it separately. Type Charge removal time (±1,000 V→±100 V) Appearance Ion balance AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Bar type 1 sec. approx. (Note 1) INDUCTIVE PROXIMITY SENSORS ±30 V or less (Note 1, 2) PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES Effective charge removal width Model No. 80 mm 3.150 in approx. ER-X008 160 mm 6.299 in approx. ER-X016 320 mm 12.598 in approx. ER-X032 480 mm 18.898 in approx. ER-X048 640mm 25.197 in approx. ER-X064 Notes: 1) In condition of discharge distance 100 mm 3.937 in, center of the product, discharge wavelength 50 Hz and no air supply. 2) Ion balance is average of plus and minus. Also, the specification value is typical value in condition of less than ±10°C ambient temperature change, set the ion balance after 30 minutes of the discharge starting, switching on the ion balance control function. Controller Power cable is not supplied with the controller. Please order it separately. Type Appearance Model No. Number of heads connected Output ER-XC02 Max. 2 units PhotoMOS relay LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS Standard type Note: ‌When using the ER-X008, use the new controller ER-XC02. The new controller ER-XC02 is compatible with existing heads of the ER-X series. The new controller can be distinguished as follows: New ER-XC02 controller MACHINE VISION SYSTEMS HEAD 1 Head connection cable Static Removers Cleaning Box Pulse Air-gun Electrostatic Sensor ER-X ER-TF ER-VS02 ER-VW ER-Q ER-F ER-XC02 DSC DSC CHECK CHECK ERROR UV CURING SYSTEMS Selection Guide Old ER-XC02 controller ER-XC02 Appearance + + 0 0 − − ERROR HEAD HEAD 2 1 The front panel design is changed. + + 0 0 − − HEAD 2 Head connection cable is not supplied with the head. Please order it separately. Model No. Description ER-XCCJ2H Length: 2 m 6.562 ft, Net weight: 120 g approx. ER-XCCJ5H Length: 5 m 16.404 ft, Net weight: 290 g approx. ER-XCCJ10H Length: 10 m 32.808 ft, Net weight: 560 g approx. Cabtyre cable with both connector Area Ionizer ER-X SERIES 1164 OPTIONS Designation Power cable FIBER SENSORS Model No. Description ER-XCC2 Length: 2 m 6.562 ft, Net weight: 80 g approx. ER-XCC5 Length: 5 m 16.404 ft, Net weight: 190 g approx. 0.15 mm2 10-core cabtyre cable with connector Cable outer diameter: ø5.3 mm ø0.209 in ER-XAPS-EX IN: 100 to 240 V AC, 50 / 60 Hz OUT: 24 V DC, 1.5 A (Note 1) AC adapter ER-XAPS AC cable Discharge needle unit Discharge part protective cover Power cable • ER-XCC□ PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AC adapter • ER-XAPS-EX Ambient temperature: 0 to +40 °C +32 to +104 °F Ground wire: 3.7 m 12.139 ft AC cable: 1 pc., Cable length 1.8 m 5.906 ft, Rating 125 V AC (Note) Wiring connector terminals: 6 pcs. LASER SENSORS • ER-XAPS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS CN-ACCN-C2 AC cable (conforming to CCC), Length: 2 m 6.562 ft INDUCTIVE PROXIMITY SENSORS CN-ACKR-C2 AC cable (conforming to KTL), Length: 2 m 6.562 ft PARTICULAR USE SENSORS ER-XANT Unit with replacement tungsten needles: 1 pc. ER-XANT2 For ER-X008 only. Unit with replacement tungsten needles: 1 pc. ER-XACVR For ER-X016/X032/X048/X064. Enables to prevent electric shock by mounting to the heads. 2 pcs per set. (Note 2) Material: polycarbonate Weight: 20 g approx. (1 set) * No effect on charge removal capacity of the heads by mounting a discharge part protection cover Notes: 1) Rating of the AC cable is 125 V AC. In case using at more than 125 V, prepare a proper cable by yourself or purchase our optional cable CN-ACCN-C2 or CN-ACKR-C2. And, the AC cable is not enclosed with ER-XAPS-EX. 2) The number of set(s) you need depends on the head model No. Model No. No. of set (2 pcs per set) ER-X016 ER-X032 ER-X048 ER-X064 1 set 2 set 3 set 4 set Discharge needle unit • ER-XANT SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS Discharge part protective cover • ER-XACVR MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Static Removers Cleaning Box Pulse Air-gun Electrostatic Sensor ER-X ER-TF ER-VS02 ER-VW ER-Q ER-F 1165 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Area Ionizer ER-X SERIES SPECIFICATIONS Heads Type Item Model No. Effective charge removal width Cleaning Box Pulse Air-gun Electrostatic Sensor ER-X ER-TF ER-VS02 ER-VW ER-Q ER-F ER-X032 80 mm 3.150 in approx. 160 mm 6.299 in approx. Ion balance ±30 V or less (Note 1, 2) Discharge method Pulse AC method Discharge output voltage ±7,000 V approx. Ozone generation 0.01 ppm or less Maximum air pressure ER-X048 ER-X064 320 mm 12.598 in approx. 480 mm 18.898 in approx. 640 mm 25.197 in approx. 1 second or less (Note 1) 0.5 MPa Applicable fluid Air (dried clean air) (Note 3) Ambient temperature 0 to +50 °C +32 to +122 °F (No dew condensation), Storage: –10 to +65 °C +14 to +149 °F Ambient humidity 35 to 65 % RH, Storage: 35 to 85 % RH Vibration resistance 10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each Shock resistance 100 m/s2 acceleration (10 G approx.), in X, Y and Z directions for three times each Enclosure grounding method Floating Main unit enclosure: PPS, Stainless steal (SUS) Head mounting bracket: Stainless steal (SUS), Discharge needle: Tungsten Material Net weight 330 g approx. 410 g approx. 530 g approx. 650 g approx. 780 g approx. Notes: 1) In condition of discharge distance 100 mm 3.937 in, center of the product, discharge wavelength 50 Hz and no air supply. 2) Ion balance is average of plus and minus. Also, the specification value is typical value in condition of less than ±10 °C ambient temperature change, set the ion balance after 30 minutes of the discharge starting, switching on the ion balance control function. 3) Dried clean air is the air passing through air dryer (dew point –20 °C –4 °F approx.) and air filter (mesh size 0.01 μm 0.0004 mil approx.) Controller Type Item Model No. Number of heads connected Supply voltage Current consumption Indictor DSC (Discharge) Controller ER-XC02 Maximum 2 units 24 V DC ±10 % 450 mA or less when connecting 1 heads, 800 mA or less when connecting 2 heads Displays status of Head 1 and 2 Green LED (lights up when discharging) CHECK Orange LED (lights up when dirt, wear, etc. of the discharge needle is detected) ERROR Red LED (lights up when abnormal discharge is detected) Level meter Static Removers ER-X016 Charge removal time Output Selection Guide Head ER-X008 ALARM ERROR COM (Common) Output operation Short-circuit protection Discharge control input (DSC OFF) Ambient temperature Ambient humidity Voltage withstandability Green LED (5 levels, lights up depending on amount of the charge or ion generation) PhotoMOS relay output • Maximum load current: 100 mA • Applied voltage: 30 V DC or less (between output-output common) • Residual voltage: 1.5 V or less (at load current of 100 mA) ALARM: ON when dirt or wear of the discharge needle is detected; OFF when operation is normal. ERROR: OFF when abnormal discharge is detected; ON when operation is normal. Incorporated (automatic reset type) Discharge allowed: Open, Discharge halt: 24 V or 0 V shorted 0 to +50 °C +32 to +122 °F (No dew condensation), Storage: –10 to +65 °C +14 to +149 °F 35 to 65 % RH, Storage: 35 to 85 % RH 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 MΩ, or more, with 250 V megger between all supply terminals connected together and enclosure Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each Shock resistance Enclosure grounding method Material Weight Accessories 100 m/s2 acceleration (10 G approx.) in X, Y and Z directions for three times each Floating Enclosure: ABS 130 g approx. Power supply / I/O connector: 1 set (Housing 5557-10R, Terminal 5556TL [manufactured by Molex]) Ground wire (3.7 m 12.139 ft approx.): 1 pc. Area Ionizer CHARGE REMOVAL CHARACTERISTICS (TYPICAL) 1166 ER-X SERIES Please contact our office for details on data that is not listed here. LASER SENSORS Measured using a 150 × 150 mm 5.906 × 5.906 in CPM (charge plate monitor). (At center of CPM) Common PHOTOELECTRIC SENSORS Correlation between charge removal Correlation between charge removal Correlation between charge removal distance and charge removal time (50 Hz) distance and charge removal time (10 Hz) distance and charge removal time (1 Hz) 200 100 0 0.1 0.2 0.3 0.4 0.5 ─ Airless ─ 0.005 MPa ─ 0.1 MPa ─ 0.3 MPa ─ 0.5 MPa 8 6 CPM Center L 4 2 0 10 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) Applied pressure (MPa) ─ Airless ─ 0.005 MPa ─ 0.1 MPa ─ 0.3 MPa ─ 0.5 MPa 8 6 CPM Center L 4 2 10 Charge removal time (sec.) 10 − ER-X064 − ER-X048 − ER-X032 − ER-X016 Charge removal time (sec.) Air flow [ℓ/min. (ANR)] 400 Charge removal time (sec.) Air flow 300 8 6 PRESSURE / FLOW SENSORS L 4 INDUCTIVE PROXIMITY SENSORS 2 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) 0 LIGHT CURTAINS / SAFETY COMPONENTS CPM Center 0 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. Center L −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) CPM + − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 Center 0 −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) Charge removal field (vertical direction, 0.005 MPa, 50 Hz) Charge removal width W (mm in) Center 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 Charge removal field (vertical direction, airless, 1 Hz) Charge removal width W (mm in) CPM + Charge removal field (vertical direction, airless, 10 Hz) Charge removal width W (mm in) Charge removal width W (mm in) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 CPM + Center − L W STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 PLC − 1 sec. − 2 sec. − 5 sec. − 10 sec. 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) − 1 sec. − 2 sec. − 5 sec. − 10 sec. 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + Center L − W − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) Charge removal field (vertical direction, 0.5 MPa, 10 Hz) Charge removal width W (mm in) − 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 Center 0 Charge removal field (vertical direction, 0.5 MPa, 50 Hz) Charge removal width W (mm in) L W Charge removal width W (mm in) CPM + Center Charge removal field (vertical direction, 0.005 MPa, 1 Hz) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + Center L − HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) − W − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 Static Removers Cleaning Box Pulse Air-gun Electrostatic Sensor ER-X CPM Center + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM Center + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) Charge removal width W (mm in) CPM + 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 UV CURING SYSTEMS Selection Guide Charge removal field Charge removal field Charge removal field (horizontal direction, airless, 50 Hz) (horizontal direction, airless, 10 Hz) (horizontal direction, airless, 1 Hz) Charge removal width W (mm in) Charge removal field (vertical direction, 0.5 MPa, 1 Hz) MACHINE VISION SYSTEMS W ER-X032 Common Charge removal width W (mm in) Charge removal width W (mm in) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 Charge removal width W (mm in) WIRE-SAVING SYSTEMS FA COMPONENTS Charge removal field (vertical direction, 0.005 MPa, 10 Hz) L SENSOR OPTIONS MEASUREMENT SENSORS Common −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 PARTICULAR USE SENSORS SIMPLE WIRE-SAVING UNITS Charge removal field (vertical direction, airless, 50 Hz) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 Center 0 MICRO PHOTOELECTRIC SENSORS AREA SENSORS ─ Airless ─ 0.005 MPa ─ 0.1 MPa ─ 0.3 MPa ─ 0.5 MPa Common −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 FIBER SENSORS 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 ER-TF ER-VS02 ER-VW − 1 sec. − 2 sec. − 5 sec. − 10 sec. CPM Center + −100 −3.937 L − W −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) ER-Q ER-F 1167 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Static Removers Cleaning Box Pulse Air-gun 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 ER-VS02 ER-VW ER-Q ER-F Charge removal width W (mm in) Charge removal width W (mm in) CPM + L − W − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) Charge removal field (horizontal direction, 0.5 MPa, 1 Hz) 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 Center 0 −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + L − W − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) Charge removal field (horizontal direction, airless, 50 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 0 Center −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) Charge removal field (horizontal direction, airless, 10 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 0 Center −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) ER-X064 800 31.496 600 23.622 400 15.748 200 7.874 Center 0 −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. − 10 sec. 100 200 300 400 500 600 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) Charge removal field (horizontal direction, 0.005 MPa, 50 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 0 Center −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) Charge removal field (horizontal direction, 0.005 MPa, 10 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 0 Center −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) ER-X064 800 31.496 600 23.622 400 15.748 200 7.874 0 −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 Charge removal field (horizontal direction, 0.005 MPa, 1 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 0 Center −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 CPM + L − W − 1 sec. − 2 sec. − 5 sec. 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) ER-X008 Charge removal field (horizontal direction, 0.5 MPa, 50 Hz) Charge removal width W (mm in) ER-TF CPM + L − W Charge removal field (horizontal direction, airless, 1 Hz) Electrostatic Sensor ER-X Center −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) Charge removal width W (mm in) PLC − 1 sec. − 2 sec. − 5 sec. − 10 sec. Center −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 Charge removal width W (mm in) LASER MARKERS 200 400 600 800 1,000 7.874 15.748 23.622 31.496 39.370 Charge removal distance L (mm in) −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + L − W 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 Center CPM + L − W − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) Charge removal field (horizontal direction, 0.5 MPa, 10 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 0 −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 Center CPM + L − W − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) Charge removal field (horizontal direction, 0.5 MPa, 1 Hz) 800 31.496 600 23.622 400 15.748 200 7.874 Center 0 −200 −7.874 −400 −15.748 −600 −23.622 −800 −31.496 0 Charge removal field (horizontal direction, 0.005 MPa, 10 Hz) 300 11.811 CPM + L − W Charge removal width W (mm in) STATIC ELECTRICITY PREVENTION DEVICES − 1 sec. − 2 sec. − 5 sec. − 10 sec. 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 Center 0 Charge removal field (horizontal direction, 0.5 MPa, 50 Hz) ER-X064 Charge removal field (horizontal direction, 0.5 MPa, 10 Hz) Charge removal width W (mm in) MEASUREMENT SENSORS −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + L − W ER-X032 Charge removal width W (mm in) WIRE-SAVING SYSTEMS Center Charge removal width W (mm in) SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS − 1 sec. − 2 sec. − 5 sec. − 10 sec. 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 Charge removal width W (mm in) PARTICULAR USE SENSORS −100 −3.937 −200 −7.874 −300 −11.811 −400 −15.748 −500 −19.685 0 CPM + L − W Charge removal field (horizontal direction, 0.005 MPa, 1 Hz) Charge removal width W (mm in) INDUCTIVE PROXIMITY SENSORS Center Charge removal width W (mm in) PRESSURE / FLOW SENSORS 500 19.685 400 15.748 300 11.811 200 7.874 100 3.937 0 Charge removal width W (mm in) LIGHT CURTAINS / SAFETY COMPONENTS Charge removal field Charge removal field (horizontal direction, 0.005 MPa, 50 Hz) (horizontal direction, 0.005 MPa, 10 Hz) Charge removal width W (mm in) AREA SENSORS ER-X032 Charge removal width W (mm in) MICRO PHOTOELECTRIC SENSORS Measured using a 150 × 150 mm 5.906 × 5.906 in CPM (charge plate monitor). (At center of CPM) Charge removal width W (mm in) PHOTOELECTRIC SENSORS ER-X SERIES CHARGE REMOVAL CHARACTERISTICS (TYPICAL) Please contact our office for details on data that is not listed here. FIBER SENSORS LASER SENSORS Area Ionizer Center 200 7.874 100 3.937 0 −100 −3.937 − 0.5 sec. − 1 sec. − 2 sec. 200 400 600 800 1,000 1,200 1,400 1,600 7.874 15.748 23.622 31.496 39.370 47.244 55.118 62.992 Charge removal distance L (mm in) CPM + L − W −200 −7.874 −300 −11.811 0 − 1 sec. − 2 sec. − 5 sec. − 10 sec. 300 400 600 100 500 200 3.937 7.874 11.811 15.748 19.685 23.622 Charge removal distance L (mm in) Area Ionizer ER-X SERIES 1168 I/O CIRCUIT AND WIRING DIAGRAMS When connecting the output to negative common 6 2 3 4 5 6 7 8 9 10 (Front view) Housing: 5569-10A [Manufactured by Molex] Terminal No. Terminal name 3 8 1 Color code 1 0V Blue 2 – 4 COM(–) Discharge control input COM(OUT) Violet 5 F.G. terminal Green/Yellow 6 24 V Brown 7 COM(+) – 8 COM(IN) White 9 Alarm output Orange 10 Error output Black 3 10 Pink Note: C  olor code refers to cable colors of an optional power supply cable. (Brown) +V 6 7 COM(+) (White) COM (IN) 8 (Pink) Discharge control input 3 (Brown) +V 7 COM(+) (Violet) COM (OUT) 4 (Orange) Alarm output Load 9 Main circuit 1 When connecting the output to positive common *1 (Black) Error output Load (Pink) Discharge control input + 24 V DC – ±10 % (White) COM (IN) Main circuit Power connector pin arrangement FIBER SENSORS 9 10 (Blue) 0 V 4 2 COM(─) 5 Internal circuit (Green/Yellow) F.G. PHOTOELECTRIC SENSORS *2 (Orange) Alarm output Load (Black) Error output + – 24 V DC ±10 % (Blue) 0 V 1 2 COM(–) Be sure to ground. 5 User’s circuit (Green/Yellow) F.G. Internal circuit *1 Be sure to ground. SENSOR OPTIONS or or Contact “closed” or transistor ON: Discharge halt Contact “open” or transistor OFF: Starting discharge Contact “closed” or transistor ON: Discharge halt Contact “open” or transistor OFF: Starting discharge SIMPLE WIRE-SAVING UNITS Notes: 1) Be sure to ground the F.G. terminal. If F.G. terminal is not connected properly, it may cause electric shock. 2) To stop discharge, turn ON the discharge control input for 20 ms or longer. To start discharge, turn OFF (open) the discharge control input. Discharge will start in 20 ms. • Never use this product in a device for personnel protection. • In case of using devices for personnel protection, use products which meet laws or standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. • Do not use this product in places where there may be a danger of flammable or combustible items being present. • To prevent electric shock and to conduct proper discharge, be sure to ground a frame ground (F.G.) terminal of a controller. • Do not place hands near the discharge needle. Doing so may cause electric shock. • Since the tip of the discharge needle is sharp, take sufficient care in handling the discharge needle, or injuries may result. • The high-voltage cable between the head and the highvoltage unit must be fixed and the minimum bend radius is R30 mm R1.181 in or more. In case of using at the bend radius R30 mm R1.181 in or less and using at moving part may cause fire and break down, etc. of the high-voltage cable. • Clean the discharge needle regularly (about once a week). Otherwise, optimum charge removal performance may not be achieved, and accidents or operating problems may occur. • If this product is used in a confined space, ozone emitted from this product may be detrimental. Be sure to provide ventilation. • Do not direct ionized air toward the face. Ozone may cause irritation to places such as the nose and throat. Mounting Head installation • Using 2 M4 screws or 1 M6 screw, mount the head onto the equipment housing. • Loosen the angle adjustment screw, adjust the head angle, and then fasten the head with the tightening torque of 0.5 N∙m or less. Angle adjustment screw M4 screw Angle adjustment screw M6 screw PRESSURE / FLOW SENSORS PARTICULAR USE SENSORS Non-voltage contact or NPN transistor/open collector PRECAUTIONS FOR PROPER USE AREA SENSORS INDUCTIVE PROXIMITY SENSORS User’s circuit *2 Non-voltage contact or PNP transistor/open collector MICRO PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Load (Violet) COM (OUT) LASER SENSORS Refer to p.1501 for general precautions. Notes: 1) Be sure to ground the equipment housing onto which the head is mounted. 2) The distance between the head and the charge removing object should be 30 mm 1.181 in or more. If the static buildup of the charge removing object is 30 kV or more, set the distance to 50 mm 1.969 in or more. 3) If there is metal near the head or between the head and the charge removing object, ion is absorbed, hindering appropriate static removal. Install the head under the following installation condition. 4) In case using the side mounting, the discharge frequency should be 10 Hz or more. • Back-side mounting (All frequencies) • Side mounting (10 Hz or more) 50 mm 1.969 in or more 50 mm 1.969 in or more Surrounding metal WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS The discharge muzzle must exceed this line (surrounding metal.) 5) When installing two or more heads set the same frequency and keep the distance as below. In face to face or parallel using different frequency, keep the distance between the heads 400 mm 15.748 in or more. • Face-to-face installation • Parallel installation Selection Guide Static Removers Cleaning Box Pulse Air-gun Electrostatic Sensor 100 mm 3.937 in or more ER-X ER-TF 50 mm 1.969 in or more ER-VS02 High-voltage unit installation • Use 2 M4 screws or 2 M6 screws to fasten the head. The tightening torques for fastening, are as follows. When using M4 screws: 1.2 N·m When using M6 screws: 2.5 N·m M6 screw M4 screw Notes: 1) Do not place any objects on top of the highvoltage unit. 2) When using multiple heads, keep the distance of at least 10 mm 0.394 in 10 mm between the high-voltage units. 0.394 in 3) W  hen fastening the high-voltage unit or more using M6 screws, fasten before connecting the head connection cable. ER-VW ER-Q ER-F 1169 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Area Ionizer ER-X SERIES PRECAUTIONS FOR PROPER USE Refer to p.1501 for general precautions. PIPING Controller installation • Air supplied to this product will reduce contamination of the discharge needle and improve the charge removal speed. • The outer diameter of the air tube to fit to the air inlet portion of this product should be ø6 mm ø0.236 in. • Make sure that clean air (air containing no water, no oil and no dust) should be supplied. • Since the pressure will drop when the air piping from the main pressure supply is extended or pneumatic components (e.g., needle valve, speed controller, mini filter) are added, keep an eye on the pressure supply to the ionizer making sure it is not in short supply. For the pneumatic components, select those that can accommodate the air supply flow rate. • Mount the controller on a 35 mm 1.378 in wide DIN rail or using M4 screws. Lock release lever AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS 2 1 35 mm 1.378 in wide DIN rail • Pull the lock release lever to remove this product from the DIN rail. M4 screw SIMPLE WIRE-SAVING UNITS Head section Air inlet WIRE-SAVING SYSTEMS ø6 mm ø0.236 in tube MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS 11.4 mm 0.449 in Note: After inserting the tube into the joint of this product, always make sure that the tube is all the way in and securely inserted. Insufficient tube insertion will cause air leakage. • The tightening torque should be 1.2 N•m or less. PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. ER-X008 Head ø6.9 ø0.272 high-voltage cable 500 mm 19.685 in long UV CURING SYSTEMS 2-ø6.5 ø0.256 mounting holes 6 0.236 180 7.087 17 0.669 160 6.299 28.5 1.122 9.4 0.370 Joint for ø6 ø0.236 air tube 28.5 1.122 9.4 0.370 106 4.173 40 40 1.575 1.575 28 1.102 18 0.709 Selection Guide 5 0.197 Static Removers 2-ø4.5 ø0.177 mounting holes Cleaning Box Electrostatic Sensor 38 1.496 (18) (0.709) ER-X 35 1.378 10.5 0.413 170 6.693 ER-Q ER-F 9.5 0.374 Points of discharge needle ion air outlet 163 6.417 ø12 ø0.472 150 5.906 138 5.433 162 6.378 22 0.866 4.2 0.165 30 1.181 (25) (0.984) 9.4 0.370 ER-VS02 ER-VW Clean air outlet (4 points) 2-ø6.5 ø0.256 Pulse Air-gun ER-TF 31 1.220 192 7.559 6.2 0.2441 6 0.236 18 0.709 Head mounting bracket 28.4 1.118 18 0.709 Discharge needle unit Area Ionizer DIMENSIONS (Unit: mm in) ER-X016 ER-X032 35 1.378 ER-X064 2-ø4.5 ø0.177 mounting holes 10.5 0.413 31 1.220 162 6.378 28.4 1.118 40 1.575 6 0.236 192 7.559 4.2 0.165 18 0.709 6.2 0.244 9.4 0.370 A 40 1.575 PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS D C 22 0.866 30 1.181 18 0.709 Head mounting bracket Discharge needle unit Model No. A B C D (E) ER-X016 120 4.724 194 7.638 226 8.898 238 9.370 251 9.882 ER-X032 280 11.024 354 13.937 386 15.197 398 15.669 411 16.181 ER-X048 440 17.323 514 20.236 546 21.496 558 21.969 571 22.480 ER-X064 600 23.622 674 26.535 706 27.795 718 28.268 731 28.780 PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES Mounting drawing with discharge part protective cover (ER-XACVR) (18) (0.709) Model No. 45.7 1.799 15.7 0.618 159.6 6.283 (160) (6.299) (F) LASER SENSORS AREA SENSORS Head mounting bracket Discharge part protective cover FIBER SENSORS MICRO PHOTOELECTRIC SENSORS Clean air outlet (4 points) 4.2 0.165 9.4 0.370 28.5 1.122 B (E) 2-ø6.5 ø0.256 18 ø12 0.709 ø0.472 170 6.693 Joint for ø6 ø0.236 air tube 9.5 0.374 Points of discharge needle ion air outlet Details of a head mounting bracket ø6.5 ø0.256 28.5 1.122 9.4 0.370 160 6.299 (25) (0.984) 9.4 0.370 Head 180 7.087 5 0.197 (18) (0.709) The CAD data in the dimensions can be downloaded from our website. ø6.9 ø0.272 high-voltage cable 500 mm 19.685 in long 6 0.236 2-ø6.5 ø0.256 17 mounting holes 0.669 28 1.102 18 0.709 38 1.496 ER-X048 1170 ER-X SERIES 18 0.709 25.4 1.000 (F) ER-X016 159.6 6.283 ER-X032 319.6 12.583 ER-X048 479.6 18.882 ER-X064 639.6 25.181 LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS ER-XC02 Controller ER-XCCJ□H (16) (0.630) (16) (0.630) (ø6) (9.1) (0.358) (ø0.236) For head 1 Head connection connector S12B-PUDSS-1 [Manufactured by JST Mfg.Co., Ltd.] (9.3) (0.336) 5.2 0.205 6.5 0.256 7 0.276 7 0.276 L • Length L (9.1) (0.358) (14) (0.551) For head 2 44 1.732 Head connection cable (14) (0.551) (8.8) (0.346) (8.8) (0.346) Model No. Length L ER-XCCJ2H 2,000 78.740 ER-XCCJ5H 5,000 196.850 ER-XCCJ10H 10,000 393.701 18 0.709 53 2.087 39 1.535 10 0.394 ER-XCC□ Power cable (Optional) Suitable for 35 mm 1.378 in width DIN rail (103.5) (4.075) 76 97 2.992 3.189 (19.6) (0.772) Selection Guide (140) (5.512) (14.4) (0.567) ER-XAPS(-EX) Model No. Length L ER-XCC2 2,000 78.740 ER-XCC5 5,000 196.850 AC adapter (Optional) F.G. wire 3.7 m 12.139 ft 4 0.157 (14.4) (0.567) 2-ø5 ø0.197 mounting holes Power supply connection connector 5569-10A [Manufactured by Molex] (22.2) (0.874) Cable 1.8 m 5.910 ft (19.6) (0.772) 95.9 3.776 28 1.102 43.8 1.724 Note: The AC cable is not enclosed with ER-XAPS-EX. Cleaning Box Pulse Air-gun • Length L L (ø5.3) (ø0.209) (22.2) (0.874) 35.4 1.394 90 3.543 (23.2) (0.913) UV CURING SYSTEMS Static Removers 27.3 1.075 60 2.362 (16.5) (0.650) 9.2 0.362 MACHINE VISION SYSTEMS AC cable 1.8 m 5.910 ft (Note) Electrostatic Sensor ER-X ER-TF ER-VS02 ER-VW ER-Q ER-F