ERZ-V20R511

Date To: : November 29.2017 PIDSA PRODUCT RＥＦＥＲＥＮＣＥ ＤＡＴＡ ＳＨＥＥＴ Product Description Product Part Number ZNR SURGE ABSORBER : ERZV20R□□□（□□□＝201 to 511) : Deveice Solutions Business Division Prepared by : Automotive & Industrial Systems Company Contact Person : Panasonic Corporation Signature : Masayoshi Kanazawa Title : Charge Check by : Name(Print） 1037-2 Kamiosatsu, Chitose City, Engineering Section Hokkaido 066-8502 Japan Phone : +81-123-23-8194 Signature Name(Print） Title : Naoki Saito : Engineer CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 1 DATE - 20 Novembar 1, 2016 [HANDLING PRECAUTIONS] ！ Precautions for Safety In the case that a ZNR surge absorber (Type D, Series V ) (hereafter referred to as the ZNR ,or product name) is used if an abnormality takes place because of peripheral conditions of the ZNR (material, environments, power source conditions, circuit conditions, etc. in equipment design), fire, electric shock, burn, or product failure may be occur. The precautions for this product are described below, understand the content thoroughly before usage. For more questions, contact us. 1. ！ Precautions to be strictly observe 1.1 Confirmation of performance ratings Use the ZNR within its rated range of performance such as the Max. allowable voltage, withstanding surge current, withstanding energy, impulse life (surge life), average pulse power, and operating temperature range. If used outside the range, the ZNR can be degrade and have element fracture, which may result in smoking and ignition. 1.2 To avoid accidents due to unexpected phenomena, take the following measures 1) In the event of fracture of the ZNR, its pieces may scatter ; hence, put the case or cover of the set product in place. 2) Do not install the ZNR near combustible substances (polyvinyl chloride wires, resin moldings, etc.). If it is difficult to do, install a nonflammable cover. 3) Across-the-line use When the ZNR is used across a line, put a current fuse in series with the ZNR. (Refer to Item 2.1.1 (4) and Table 1.) 4) Use between line to ground (1) In the case that the ZNR is used between a line to the ground, the short-circuit of the ZNR may not blow the current fuse because of grounding resistance, which may cause smoking and ignition of the ZNR's exterior resin. As the measure against it, install an earth leakage breaker on the power supply side of the ZNR position. If no earth leakage breaker is installed, use a thermal fuse together with a current fuse in series. (Refer to Table 1.) (2) In the case that the ZNR is used between a live part and metal case, a electric shock may develop at a short circuit of the ZNR ; hence, ground the metal case to the ground or keep it from the human body. 2. Application notes 2.1 Pay attention to the following items to avoid the shortened life and failure of the ZNR 1) Circuit conditions (1) Select a ZNR of which the maximum voltage including fluctuations in source voltage allows for the maximum permissible circuit voltage. (Refer to Table 1.) (2) In cases that surges are intermittently applied at short intervals (for example, in the case that the voltage of the noise simulator test is impressed etc.), do not cause them to exceed the ZNR's rated pulse power. (3) Select a ZNR recommended in Table 1. Across the Line (Line to Line) use If possible, use a Part No. marked with * incase of voltage temporarily rises load unbalance of separately-wired loads, short between hot and neutral-line, open of neutral line in singlephase-three-wired system, and due to resonance at switching for a capacitive, inductive load. Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 2 - 20 Used between line to ground Use a different Part No. from "Across-the-line use" as table 1, because of raising voltage in case of "Line to Ground Fault". Use a part No. marked with ** in table 1, in case of the insulation resistance test (500VDC) for equipment. When using a part of the varistor voltage that the insulation efficiency examination can not be cleared, there is a case where the surge absorber can be done by removing it from the circuit depending on the circuit condition (Refer examination of Japan Domestic Safety Regulations). Use a Part No. marked with *** in table 1, in case of the withstanding voltage test (1000VAC or 1200VAC) for equipment. (4） Concerning current fuse We recommended to selecting a ZNR and the rated current of a current fuse as follows. Finally, please be sure that there is no danger if the ZNR mounted on equipment breaks. Series V05 V07 V09 V10 V14 V20 ERZV20++++ Std. Bulk P/N ERZV05++++ ERZV07++++ ERZV09++++ ERZV10++++ ERZV14++++ Std. Taped P/N ERZV+5++++ ERZV+7++++ ERZV+9++++ ERZV+A++++ ERZV+E++++ 5A max 7A max 7A max 10A max Fuse rated current 3A max ＊ Fuses shall use rated voltages appropriate for circuits. ＊ Refer to Item ( 2.1 5) ) " CSA safety standard approved fuse" as well. The recommended fuse position is shown in table 1, "Example of ZNR application", however, if the load current of protected equipment is larger than that of the above recommended fuse rated current, install a current fuse at the position shown below. Power Source Side Current Fuse Ｚ ZNR (5) Concerning thermal fuse Set a thermal fuse to get high thermal conductivity with ZNR. Note/Revision Panasonic Corporation Protected Equipment 10A max CLASSIFICATION PRODUCT REFERENCE DATA SHEET SUBJECT Table 1 ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 3 - 20 Example of ZNR application Measure against across-the-line surge DC/AC single-phase Measure against surge across the line and between the line and ground DC/AC single-phase ｆ L ｆ L ZNR1 N Protected Equipment N ZNR2 ZNR2 Thermal Fuse Thermal coupling f : fuse Connection example Protected Equipment ZNR1 f : fuse AC 3-phase AC 3-phase ｆ ｆZNR3 ｆ ｆ ZNR3 ｆ ZNR3 Protected Equipment ｆZNR3 Protected Equipment ZNR3 ZNR3 ZNR4 ZNR4 Thermal coupling f : fuse ZNR4 Thermal fuse f : fuse ZNR Across the Line (Line to Line) use Source Nominal varistor voltage voltage AC100V Example of rating selection ZNR1 ZNR3 Line to Ground use ZNR Source voltage * 201 to 361 AC100V∼ AC220V * AC120V 241 to 431 AC200V 471 to 621* AC220V 471 to 621 AC240V 511,621 AC380V 821 ZNR2 ZNR4 * AC230V∼ AC240V * Note/Revision Panasonic Corporation AC380V Nominal varistor voltage 471 511 * 621 821_and_more** *** 182 511 * 621 ** 821 and more *** 182 112** *** 182 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 4 - 20 2) Operating environments (1) The ZNR is designed and manufactured for application in general purpose electronic devices. The ZNR shall not be exposed to the weather, except for usage inside unit. (2) Do not use the ZNR in places exposed to temperatures beyond the operating temperature range, such as places exposed to sunlight and vicinities of heating equipment. (3) Do not use the ZNR in places exposed to high temperatures and high humidity, such as places exposed directly to rain, wind, dew condensation, and vapor. (4) Do not use the ZNR in dusty and salty places and atmospheres polluted by corrosive gases. 3) Processing conditions (1) Do not wash the ZNR by such solvents (thinner, acetone, etc.) as its exterior resin deteriorates. (2) Do not apply a strong vibration, shock (by falling, etc.) to the ZNR, cracking to its exterior resin and element may occur. (3) When coating the ZNR with resin (including molding), do not use such resin. (4) Do not bend the ZNR lead wires at the position close to its ZNR exterior resin, or apply external force to the position. (5) When soldering the ZNR lead wires, follow the recommended condition and do not melt the solder and insulating materials constituting the ZNR. Soldering Method Recommended Condition Attention Flow soldering 260deg.C, within 10sec Type D is not Reflow soldering object part. Type D *1 When using at the thing except the condition that it is possible to suggest to the above, confirm that there is not a problem. The limit of the repair be once and go in solder temperature within 400℃ and moreover within 5 seconds. *2 Profile be careful because there is a margin of error in the way of measuring. *3 The temperature depend on the size and the package density of the substrate. Therefore, confirm every kind of the substrate. ● Soldering temperature-time profile to recommend Soldering Preheating Temperature Gradual Time Preheating The normal to 130deg.C max.120s Soldering Gradual cooling max.260deg.C max.10s Gradual cooling Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 5 - 20 4) Long-term storage (1) Do not store the ZNR under high temperature and high humidity. Store it at temperature up to 40 degree-C and at humidity below 75%RH, and use it within two years. Before using the ZNR that has been stored for a long period (two year or longer), confirm the solderability. (2) Avoid atmospheres full of corrosive gases (hydrogen sulfide, sulfurous acid, chlorine, ammonia, etc.). (3) Avoid direct sunlight and dew condensation. 5) Application notes for CSA (1) CSA regulate "Maximum Rating of Fuse"for using ZNR to "Audio,Video and Similar Electronic Equipment" as below. Maximum Peak Current 8/20 μs, 1 time (A) Maximum Rating of Fuse (A) 500 and under 3 Over 500 to 2000 and under 5 Over 2000 to 6000 and under 10 Over 6000 Not specified. （2） "Rated Voltages" are specified for UL/CSA recognized components besides Maximum Allowable Voltage because of conforming to the Standby Current specified in safety standards. In case of making an application to UL/CSA approval for equipment with ZNR, the maximum AC operating voltage of equipment shall be lower than the ZNR Rated Voltage. 3. Notices 3.1 In cases that the ZNR is used in equipment (aerospace equipment, medical equipment, etc.) requiring extremely high reliability, ask us for selection of Part No., and protection coordination, etc. in advance. 3.2 There is possibility that the ZNR will unexpectedly smoke or ignite because of abnormal rise of the circuit voltage and invasion of excessive surge. To prevent that accident from spreading over the equipment and not to expand the damage, use multiplex protection such as the adoption of frame-retardant materials for housing parts and structural parts. 3.3 Package marking includes the product number, quantity, and country of origin. As a rule, country of origin should be indicated in English. 4. Substances of this product 4.1 This product not been manufactured with any ozone depleting chemical controlled under the Montreal Protocol. 4.2 This product comply with RoHS(Restriction of the use of certain Hazardous Substance in electrical and electronic equipment) Directive(2011/65/EU). 4.3 All the materials used in this part are registered material under the Law Concerning the Examination and Regulaon of Manufacture, etc. of Chemical Substance Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 6 - 20 [SPECIFICATIONS] 1. Scope, Part Numbers, Construction 1.1 Scope This specification applies to the ZNR Surge Absorbers (Bulk Type). 1.2 Part Numbers Explanation of Part Numbers 1 2 3 4 5 6 7 E R Z V 2 0 R Product V20 Code V20 series 8 9 10 11 12 Design no. Series Lead Configuration R W:7.5mm Note/Revision Panasonic Corporation Nominal Varistor Voltage The first two digits are significant figures and the third one denotes the number of zeros following. CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 7 1.3 Construction ① ZNR Element ① ＺＮＲ Ｅｌｅｍｅｎｔ ＺＮＲ素子   ＺＮＲ素子   ② Electrode ② Ｅｌｅｃｔｒｏｄｅ 電極   電極 ③ Internal solder ③ Ｓｏｌｄｅｒ material   はんだ 内部はんだ ④ Coating ④ Ｃｏａｔｉｎｇ   外装樹脂   外装樹脂 Lead Wires   ⑤Ｌｅａｄ Ｗｉｒｅｓ ⑤    リード線   リード線 Item 部品名 Material 材 質 ① ZNR Element ＺＮＲ素子 ZnO Ceramics etc. 酸化亜鉛 他 ② Electrode 電極 Silver 銀 ③ Internal solder material 内部はんだ Sn-Ag-Cu ④ Coating 外装樹脂 Epoxy Resin（UL94 V-O approved） エポキシ樹脂（UL94 V-0 認定品） ⑤ Lead Wires リード線 series シリーズ :V20 :V20 Tin(Sn100%) Plated Copper 錫(Sn100%)メッキ銅線 Note/Revision Panasonic Corporation - 20 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 2. Appearance, Dimensions 2.1 Appearance Without dirt and crack, marking should be clear. 2.2 Dimensions Refer to Figure 1.1 to 1.2 and table 1.1 to 1.2. Fig. 1.1 Straight Lead Type Part No ：ERZV20R271 Note/Revision Panasonic Corporation 8 - 20 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 9 - 20 3. Electrical Requirements Listed below of Specifications, Test Specifications, and Test Methods. Individual specifications is in the table 2 Characteristics 3.1 Max. allowable voltage Specifications AC ：Table 2 DC ：Table 2 3.2 Rated voltage AC ：Table 2 3.3 Rated wattage Table 2 3.4 Varistor voltage 3.5 Clamping voltage V1 Table 2 Table 2 Maximum peak current 1 pulse 3.6 (Withstanding surge current) 3.7 Maximum energy 3.8 Temperature coefficient of varistor voltage 2 pulses Measuring current : 1mA DC Measuring current : Table 2 Current Waveform : 8/20μs Table 2 Impulse : 8/20μs Table 2 Impulse : 8/20μs at interval of 5 min. Table 2 Impulse : 2ms , 1 pulse Table 2 Impulse : 10/1000μs, 1 pulse 0∼−0.05%/℃ 3.9 Capacitance Table 2 3.10 Dielectric loss Table 2 3.11 Withstand voltage Test Specifications No breakdown Measured voltage : V1 Temp. range : ＋25℃ to ＋85deg.C Measuring frequency : 1kHz 1MHz (below 100pF) Measuring frequency : 1kHz 1MHz (below 100pF) Applied voltage : Table 2 Time : 1 min. Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 10 - 20 3.Electrical Test M ethods Test M ethods/Description Charactenristics Environmental conditions under which every measuring is done without doubt on Standard test condition the measuring results. Unless specially, specified, temperature, relative humidity are 5deg.C to 35deg.C, 45 to 85%RH respectively. 3. 1 M aximum allowable voltage 3. 2 Rated voltage 3. 3 Rated wattage The maximum Sine wave voltage (rms) that can be applied continuously or maximum DC voltage in the specified environmental temperature range. The maximum Sine wave voltage (rms) that can be applied continuously in CSA recognized equipment. The maximum power to be loaded with in the specified environmental temperature range. Voltage between both terminals of ZNR measured when CmA of DC current is 3. 4 Varistor voltage applied under standard conditions. It is called Vc or VcmA. M easuring the varistor voltage should be made promptly to avoid heat affection. 3. 5 Clamping voltage 3. 6 current (8/20μs). M aximum peak current The maximum current within the varistor voltage change of ±10% with the (Withstanding surge current) standard impulse (8/20μs) applied by the specified condition. 3. 7 M aximum energy Temperature coefficient 3. 8 The maximum voltage between two terminals with the specified standard impulse The maximum energy within the varistor voltage change of ±10% when the specified impulse is applied. Coefficient indicating dependency of varistor voltage on specified temperature. of varistor voltage 3. 9 Capacitance 3.10 Dielectric loss 3.11 Withstand voltage Capacitance shall be measured at 1kHz±10％、1Vrms max. ( 1M Hz±10％ below 100pF )、0V bias and 20±2deg.C. Dielectric loss tangent shall be measured at 1kHz ±10％、1Vrms max. ( 1M Hz±10％ below 100pF )、0V bias and 20±2deg.C. The specified voltage shall be applied both terminals of the specimen connected together and metal foil closely wrapped round its body for 1 minute. Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 11 - 20 4. Mechanical Requirements Listed below of Specifications, Test Specifications, and Test Methods. 4. Mechanical Requirements Characteristics 4.1 4.2 Robustness of terminations (Tensile) Robustness of terminations (Bending) 4.3 Vibration 4.4 Solderability 4.5 Resistance to soldering heat Specifications Test Specifications No outstanding damage V20 series : 19.6N, 10s No outstanding damage V20 series : 9.8N No outstanding damage Frequency : 10 to 55Hz Amplitude : 0.75mm Time : each 2 hours Minimum 95% of the terminals should Solder temp. : 235±5℃ be covered with solder uniformly Immersed time : 2±0.5s Solder temp. : 260±5℃ Immersed time : 10±1s ΔV1 ≦ ± 5% 4. Mechanical Test Methods Characteristics Robustness of terminations 4. 1 (Tensile) Test Methods/Description After gradually applying the specified load and keeping the unit fixed for ten seconds, the terminal shall be visually examined for any damage. The unit shall be secured with its terminals kept vertical and the specified load is Robustness of terminations applied, gradually bent by 90゜in one direction, back to the original position, then 4. 2 (Bending) 90゜ in the opposite direction, and again back to the original position. The damage of the terminals is visually examined. After repeatedly applying a single harmonic vibration (amplitude ; 0.75mm ; double 4. 3 amplitude ; 1.5mm with 1 minute vibration frequency cycles(10Hz to 55Hz to 10Hz) Vibration to each of three perpendicular directions for 2 hours. The varistor shall then be visually examined. After dipping the terminals to a depth of about 3mm from the body, in the melted 4. 4 Solderability solder of 235±5℃ for 2±0.5 seconds, the terminals are visually examined. After each lead shall be dipped into a solder bath having a temperature 260±5℃ to a point 2.0∼2.5mm from the body of the unit, be held there for specified time, and 4.5 Resistance to Soldering Heat then be stored at room temperature and humidity for 1 to 2 hour. The change of Vc and mechanical damages are examined. Note : Varistor Voltage change of forward direction shall be measured in the test of uni-pole surge life and DC load life. Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 12 - 20 5. Environmental Requirements Listed below of Specifications, Test Specifications, and Test Methods. Individual specifications is in the table 2 5. Environmental Requirements 5.1 High temperature storage (Dry heat) ΔV1 ≦ ± 5% Ambient temp. : 125±2℃ Time : 1000h Ambient condition 5.2 Damp heat ΔV1 : 40±2℃, ≦ ± 5% 90 to 95%RH Time 5.3 Low temperature storage (Cold) ΔV1 ≦ ± 5% ΔV1 ≦ ± 5% : 1000h Ambient temp. : −40±2℃ Time : 1000h Step 5.4 Heat cycle No outstanding damage Temp. Period 1 −40±3℃ 30min. 2 Room Temp. 15min. 3 ＋125±2℃ 30min. 4 Room Temp. 15min. 5cycles 5.5 High temperature load (Dry heat load) ΔV1 ≦ ± 10% Ambient temp. : 85±2℃ Time : 1000h Ambient condition 5.6 Damp heat load ΔV1 : 40±2℃, ≦ ± 10% 90 to 95%RH Time Impulse life I 5.7 (Surge life I) Impulse life Ⅱ 5.8 (Surge life Ⅱ) ΔV1 ≦ ± 10% at listed table 2 ΔV1 ≦ ± 10% at listed table 2 Impulse : 8/20μs Applied condition : 10 times by interval 10s : 8/20μs Applied condition : 10 times by interval 10s -40℃ to + 85℃ Storage Temperature Range -40℃ to +125℃ Panasonic Corporation 4 Impulse Operating Temperature Range Note/Revision : 1000h 5 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 5. Environmental Test Methods High temperature storage 5. 1 (Dry heat) 13 - 20 The specimen shall be subjected to 125±2℃ for 1000 hours in a thermostatic bath without load and then stored at room temperature and humidity for 1 to 2 hours. Thereafter, the change of Vc shall be measured. The specimen shall be subjected to 40±2℃, 90 to 95%RH for 1000 hours without load and then stored at room temperature and humidity for 1 to 2 hours. 5. 2 Damp heat Thereafter, the change of Vc shall be measured. Low temperature storage The specimen shall be subjected to −40±2℃ without load for 1000 hours and then stored at room temperature for 1 to 2 hours. Thereafter, the change of Vc shall be 5. 3 (Cold) measured. The temperature cycling shall be repeated 5 times and stored at room temperature 5. 4 Heat cycle and humidity for 1 to 2 hours. The change of Vc as well as mechanical damage shall be examined. High temperature load After being continuously applied the maximum allowable voltage at 85±2℃ for 5. 5 (Dry heat load) 1000 hours, the specimen shall be stored at room temperature and humidity for 1 to 2 hours. Thereafter, the change of Vc shall be measured. The specimen shall be subjected to 40±2℃, 90 to 95%RH and the maximum 5. 6 Damp heat load allowable voltage for 1000 hours and then stored at room temperature and humidity for 1 to 2 hours. Thereafter, the change of Vc shall be measured. Impulse life I After the specified impulse is applied 10000 times continuously with the interval 10 5. 7 (Surge life I) seconds at room temperature, the specimen shall be stored at room temperature and humidity for 1 to 2 hours. Thereafter, the change of Vc shall be measured. Impulse life II After the specified impulse is applied 100000 times continuously with the interval 10 5. 8 (Surge life II) seconds at room temperature, the specimen shall be stored at room temperature and humidity for 1 to 2 hours. Thereafter, the change of Vc shall be measured. Note : Varistor Voltage change of forward direction shall be measured in the test of uni-pole surge life and DC load life. 6. Marking Contents Refer to table 3 Individual specifications of Dimensions and Electrical Requirements and Environmental Requirements are indicated below. Dimensions : Table 1 Electrical Requirements : Table 2 Environmental Requirements : Table 2 Marking Contents : Table 3 Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 14 - 20 Table 1 Series V20 Straight Lead Type 1) 品番 Part No. 付図番号 Fig. No. D max. (mm) H max. (mm) T max. (mm) W +/-1.0 (mm) L +/-1.0 (mm) B min. (mm) C +/-0.4 (mm) Φd +/(mm) 単重 Approx. (g) ERZV20R271 付図 1.1 Fig. 1.1 21.5 24.5 5.6 7.5 2.5 20.0 - 0.8 +0.08 -0.05 4.4 1) 参考値 Typical Fig 1.1 Straight Lead Type Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 15 - 20 Table 2 Series V20 Electrical Part Number Maximum Allowable Voltage ACrms DC Rated Voltage Rated wattage Varistor Voltage ACrms Environmental Clamping Voltage Maximum Peak Curent Maximum Energy (max.) 1 time 2 times 2ms Impulse Life (Surge Life) (max.) (max.) (max.) I II (J) 1kHz (pF) 1kHz (%) (V) (A) (A) (V) (V) (V) (W) (V) ERZV20R201 130 170 118 1.0 185 ∼ 225 340 100 10000 7000 100 140 1700 10 1000 250 120 ERZV20R221 140 180 127 1.0 198 ∼ 242 360 100 10000 7000 110 155 1600 10 1000 250 120 VxA(V) xA (A) (A) (J) 10/1000 μs Capaci- Di- Withtance electric stand Loss voltage ERZV20R241 150 200 136 1.0 216 ∼ 264 395 100 10000 7000 120 168 1500 10 1000 250 120 ERZV20R271 175 225 159 1.0 247 ∼ 303 455 100 10000 7000 135 190 1300 10 1000 250 120 ERZV20R331 210 270 189 1.0 297 ∼ 363 545 100 10000 6500 160 228 1100 10 1000 250 120 ERZV20R361 230 300 209 1.0 324 ∼ 396 595 100 10000 6500 180 255 1100 10 1500 250 120 ERZV20R391 250 320 227 1.0 351 ∼ 429 650 100 10000 6500 195 275 1100 10 1500 250 120 ERZV20R431 275 350 250 1.0 387 ∼ 473 710 100 10000 6500 215 303 1000 10 1500 250 120 ERZV20R471 300 385 272 1.0 423 ∼ 517 775 100 10000 6500 250 350 900 10 1500 250 120 ERZV20R511 320 410 291 1.0 459 ∼ 561 845 100 10000 6500 273 382 800 10 1500 250 120 Note/Revision Panasonic Corporation CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 16 - 20 Table 3 Series V20 Part Number 品番 Marking Contents 表示の内容 ＺＮＲ Explanation of the content 内容の説明 Trade Mark 製造者識別マーク Product Name 品名 Ｖ２０□□□Ｕ Type Name , Abbreviation of Part No. タイプ名，品番略称 □□□･･･ Nominal Varistor Voltage      公称バリスタ電圧略称 UL Recognized Component Mark UL 認定マーク CSA Monogram CSA モノグラム Factory Identification Marking ○ 工場識別コード None 表記なし ･･･ Japan 日本国 Q     ･･･ Indonesia インドネシア ERZV20R271 ＺＮＲ Ｖ２０□□□Ｕ ○◆◇ ◆ ◆ Year Code(example) 年コード(例) 0 1 ⋮ ◇ 2030 2031 ⋮ example K A ⋮ 部品表示の一例 2020 2021 ⋮ V20□□□U 0 1 ⋮ ⋮ 2010 2011 H 2038 8 2018 8 2028 J 2039 9 2019 9 2029 ･ When the tens digit of Christian era is even number, an alphabetic character (1:A, 2:B...9:J, 0:K, l is excluded.) shall be used for the abbreviation of end of Christian era. ･西暦年の＋の位が偶数年は末尾略称に英字 (1:Ａ,2::Ｂ…9:J,0:K,Iを除く)を使用する。 ･ When the tens digit of Christian era is odd number, a numeric character (End of Christian era) shall be used for the abbreviation of end of Christian era. ･西暦年の＋の位が奇数年は末尾略称に数字(西暦末尾) を使用する。 ◇ Monthly Code 月コード Jan. Jul. 1 7 Feb. Aug. 2 8 Mar. Sep. 3 9 Apr. Oct. O 4 May. Nov. N 5 Jun. Dec. D 6 Note/Revision Panasonic Corporation CLASSIFICATION PRODUCT REFERENCE DATA SHEET SUBJECT ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 17 7. Packing 7.1 Packing quantity shall be shown Table 4 7.2 ZNR Surge Absorbers shall be packed in plastic bag, and then packed into carton box. 7.3 Dimensions of packing materials and marking on the packing materials shall be shown Fig. 2.1 and Fig. 2.2 Approx. 150∼220 Approx. 90 to 120 Quantity Country of origin (marked in English) (Unit : mm) Fig 2.1 Bag Approx. 340 B Marking contents ・Part number ・Quantity ・Lot number ・Country of origin (marked in English) Approx. 210 Fig 2.2 Carton box Note/Revision Panasonic Corporation (Unit : mm) - 20 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 18 - 20 Table 4 Series V20 Part Numbers ERZV20R271 Quantity in Packing Unit pcs. Packing Quantity in Carton pcs. 50 2,000 Note/Revision Panasonic Corporation Dimension B (mm) Approx. 160 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 19 7.4 Packing Indication Contents of Label 7.4.1 Bar Code Label Specification Bar code symbology Label size Bar code height Bar code dimension Wide element width Narrow/Wide bar ratio Inter character gap Quiet zone Bar code resolution :EIAJ Code39 :90.0 mm x 45.0 mm :5 mm :0.334 mm :1:2 :0.167 mm :3.81 mm :11.70 character/inch 7.4.2 Bar Code Contents Bar Code 1 * 3N 1 Panasonic P/N Bar Code 2 * 3N 2 Bar Code 3 * 1P Panasonic P/N SP SP Serial No. SP Quantity Vender code * 7.4.3 Label Contents Panasonic P/N, Quantity, Lot.No., Country of origin, Company name, etc. 7.4.4 Constitution of Lot No. ２ ４ ０２ ＧＨ Ａ６７ day Fix Consecutive No(ex. A01,A02,…,A99,B01,…) Month(1,2,…..9,O,N,D)月 Year(Last digit) 7.4.5 Label Form and Examples (ERZV07D471) Symbols of things Note/Revision Panasonic Corporation * * - 20 CLASSIFICATION SUBJECT PRODUCT REFERENCE DATA SHEET ZNR SURGE ABSORBER V-SERIES (Bulk Type) ERZV20R271 20 - 20 8. Country of origin 8.1 Country of origin Japan Indonesia 8.2 Factory name Panasonic Corporation P T. Panasonic Industrial Devices Batam 8.3 Address 1037-2 Kamiosatsu, Chitose City, Hokkaido 066-8502 Japan Puri Industrial Park 2000, Batam Centre, Kelurahan Baloi Permai Batam 8.4 Factory Identification Method Factory Identification Marking : None Factory Identification Marking : Q Note/Revision Panasonic Corporation