EVE-PDBRL408B

Encoders/EVEP/Q 16 mm Square Encoders Type: EVEP/EVEQ Features Recommended Applications Good operational feel Long life with high click torque Shaft wobble : 0.1 mm max. Centralized control of automotive audio equipment, navigation systems, and air conditioners. Explanation of Part Numbers 1 2 3 4 Product Code 5 6 7 Function 8 9 10 Combination of Shaft & Bushing 11 12 Output (Pulses) Switch Classification E V EP E VEQ Rotation Angle 36 0 ° (Endless) Shaft Pull/Push Strength Shaft Wobble Mechanical 10 0 N min. 0.1 mm max.(Length form mounting surface : 21.5 mm) ( 50 mN·m is applied on the point 2 mm from the shaft tip) Rotation Torque 25 mN·m max. Detents 16 points 32 points Output Signals Phase A and B R e so lutio n 8 pulses / 3 6 0 ° Rating 1 mA 10 V DC (at each bit) 1 Ω max. Contact Resistance Electrical Chattering 5 ms ma x. 50 M Ω min. (at 250 V DC) Insulation Resistance 30 0 V AC for 1 minute Dielectric Withstanding Voltage Bouncing Switch Part 16 pulses/ 36 0 ° 5 m s m a x. Type S P S T P ush - o n Rating 20 mA 16 V DC Contact Resistance 10 0 mΩ max. Operating Force 6 N Travel Endurance 0. 5 m m Rotation Life (Encoder) 1,000,000 cycles min. 30,000 cycles min. Operating Life (Switch) 1,000,000 cycles min. 30,000 cycles min. Minimum Quantity/Packing Unit 50 pcs. (Tray Pack) Quantity/Carton 20 0 pcs. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 2017.09 industrial.panasonic.com/ww –1–   Panasonic Corporation 2017 ANCTB65E 201709-Fd Encoders/EVEP/Q Dimensions in mm (not to scale) D A COM. B E B:Output signal B φ1.8 +0 - 0.05 1.5 2-0.5 16.5 12.8+0 - 0.15 17.0 A:Output signal A General dimension tolerance : ± 0.5 ( )dimensions are reference dimensions. except gate area 11.8+0 - 0.15 EVEP/EVEQ +0.05 0.6 9 0 °± 3 ° 12.0 9.0±0.1 7.5 13.0 +0 - 0.2 21.5 φ13.0 - 0.1 φ12.7 +0.1 - 0.05 φ12.0 +0.05 - 0.1 Mounting surface PWB mounting hole for reference Encoder / Switch Circuit 16.6.±0.05 4-φ1.9 +0.1 -0 15.00±0.05 9.0 Center of shaft φ1.85+0.05 -0 D A COM.B E A COM 5-φ1.0+0.1 -0 P2.5x4=10 (SWITCH) D E (ENCODER) B (Tolerance:±0.1) (View from mounting side) PWB thickness t=1.6 Phase Difference Test Circuit Diagram Detent steady point 5 V DC 10 k 10 k 10 k 10 k OFF Signal A ON Signal A T1 T2 T3 Signal B T4 A B OFF 0.01 μF Signal B 0.01 μF Encoder ON C.W COM Phase difference T1, T2, T3 , T4 (At rotational speed 60 r/min.) Initial............... 8 m sec. min. After life........ 2.5 m sec. min. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ww –2–   Panasonic Corporation 2017 ANCTB65E 201709-Fd