EVPAFKB65

Light Touch Switches/EVPAF 3.0 mm×2.6 mm SMD Light Touch Switches Type: EVPAF ■ Features ● External dimensions: 3.0 mm× 2.6 mm, Height 0.65 mm ● High operability Equipped with an actuator (push plate) ● Low temperature use ■ Recommended Applications ● Operation switches for portable electronic equipment (Mobile phone, Portable audio) ■ Explanation of Part Numbers 1 2 3 Product Code 4 5 Type 6 7 8 9 Height ■ Speci cations Type Snap action/Push-on type SPST Rating 10 μA 2 Vdc to 20 mA 15 Vdc (Resistive load) Contact Resistance Electrical 500 mΩ max. Insulation Resistance 50 MΩ min. (at 100 Vdc) Dielectric Withstanding Voltage 250 Vac for 1 minute Bouncing Mechanical Endurance 10 ms max. (ON, OFF) Operating Force 1.3 N, 1.6 N, 2.4 N, 3.4 N Travel Operating Life 0.15 mm 1.3 N, 1.6 N, 3.4 N : 100000 cycles min., 2.4 N : 500000 cycles min. Operating Temperature –40 °C to +85 °C –40 °C to +85 °C (Bulk) –20 °C to +60 °C (Taping) Storage Temperature Minimum Quantity/Packing Unit 8000 pcs. Embossed Taping (Reel Pack) Quantity/Carton 40000 pcs. Note: Non washable Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 2016.09 industrial.panasonic.com/ac/e/ –1–   Panasonic Corporation 2016 ANCTB15E 201606-Fd Light Touch Switches/EVPAF A' A 4-0.5 2-1.8 2.6 (Embossed Taping) With J-bent terminals B B' φ0.65 ( 0.75) (Adhesive) 0.44 A A' B B' Circuit diagram ( 4-0.35 2-3.4 EVPAFKB65 4-0.35 +0.1 –0.15 ) (Push plate) 0.65 2-1.2±0.05 3 EVPAF (0.65) 2-3.5±0.05 2-2.4±0.05 1.6 (0.4) A' 2.6 (1.15) (0.8) A 2-2.4±0.05 No. 1 (Without the remainder of the gate) ■ Dimensions in mm (not to scale) B (1.5) (2-2.5) B' PWB land pattern for reference Part of A-A' terminal is exposed at area. Any land pattern or vias shall not be provided at area. Operating Force Height Operating Life EVPAFKB65 1.3 N 0.65 mm 100000 cycles EVPAFFB65 No. 2 1.6 N 0.65 mm 100000 cycles 3 A' 4-0.5 2-1.8 2.6 With J-bent terminals B B' φ0.65 ( 0.75) (Adhesive) (Push plate) 2-3.4 A A' B B' Circuit diagram 2-1.2±0.05 A 0.48 4-0.35 (Embossed Taping) 0.70 (0.65) 2-3.5±0.05 2-2.4±0.05 1.6 (0.4) A' 2.6 (1.15) (0.8) A B (1.5) (2-2.5) B' 2-2.4±0.05 EVPAF (Without the remainder of the gate) Part Numbers PWB land pattern for reference Part of A-A' terminal is exposed at area. Any land pattern or vias shall not be provided at Part Numbers Operating Force Height area. Operating Life EVPAF5B70 3.4 N 0.7 mm 100000 cycles EVPAF7B70 2.4 N 0.7 mm 500000 cycles Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ac/e/ –2–   Panasonic Corporation 2016 ANCTB15E 201606-Fd Light Touch Switches/EVPAF ■ Dimensions in mm (not to scale) A' 4-0.5 2-1.8 2.6 A (Embossed Taping) B B' φ0.65 (Push plate) 2-3.4 2-3.5±0.05 2-2.4±0.05 1.6 A A' B (1.15) (0.8) (0.65) (0.4) 2.6 ( 0.75) (Adhesive) A' B B' B' PWB land pattern for reference (1.5) (2-2.5) Part Numbers A Circuit diagram 4-0.3 +0.15 –0.1 With J-bent terminals 0.39 2-1.2±0.05 EVPAF 0.65 2-2.4±0.05 3 (Without the remainder of the gate) No. 3 Part of A-A' terminal is exposed at area. Any land pattern or vias shall not be provided at area. Operating Force Height Operating Life EVP0AFB65 1.6 N 0.65 mm 500000 cycles EVPAF7B65 2.4 N 0.65 mm 500000 cycles EVPAF5B65 3.4 N 0.65 mm 100000 cycles ● Embossed Carrier Taping MAX. 260 230 180 Fan or Normal Temp. Tape width=12.0 mm t1 Feeding hole 150 Chip pocket P2 P 0 E φD0 F W A B Operation Top (°C) ■ Recommended Reflow Soldering Conditions (Normal Temp.) 90±30 40±10 Soldering Time (s) Part No. EVPAF EVP0AF Height A 0.65/0.70 B t2 W 3.75±0.2 2.95±0.2 12.0±0.3 P1 Chip component Tape running direction F E P1 P2 P0 D 0 Dia t1 5.5±0.1 1.75±0.1 8.0±0.1 2.0±0.1 4.0±0.1 1.5±0.3 0.3±0.1 ● Standard Reel Dimensions in mm (not to scale) Unit: mm t2 0.8±0.2 ■ Recommended Shape of Test Pole T E B C D r φ1.5 toφ2.0 A Item A W B C t D Rate (mm) φ380.0±2.0 φ80.0±1.0 φ13.0±0.5 φ21.0±1.0 Item Rate (mm) W 13.5±1.0 T t r 17.5±1.0 _ _ R0.3 mm±0.05 mm E 2.0±0.5 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ac/e/ –3–   Panasonic Corporation 2016 ANCTB15E 201606-Fd