Light Touch Switches/EVPBA
3.0 mm×2.6 mm 2 terminals SMD
Light Touch Switches
Type:
EVPBA
■ Features
● External dimensions: 3.0 mm×2.6 mm, Height 0.58 mm
● High operability
Equipped with an actuator (push plate)
■ Recommended Applications
● Operation switches for portable electronic equipment
(Mobile phone, Portable audio)
■ Explanation of Part Numbers
1
2
3
Product Code
4
5
6
7
8
9
Type
■ Specifications
Type
Snap action/Push-on type SPST
10 μA 2 V DC to 20 mA 15 V DC (Resistive load)
Rating
Contact Resistance
Electrical
500 mΩ max.
Insulation Resistance
50 MΩ min. (at 100 V DC)
Dielectric Withstanding Voltage
250 V AC for 1 minute
Bouncing
Mechanical
Endurance
10 ms max. (ON, OFF)
Operating Force
1.8 N
Travel
0.13 mm
Operating Life
300,000 cycles min.
Operating Temperature
–40 °C to +85 °C
–40 °C to +85 °C (Bulk)
–20 °C to +60 °C (Taping)
Storage Temperature
Minimum Quantity/Packing Unit
20,000 pcs. Embossed Taping (Reel Pack)
100,000 pcs.
Quantity/Carton
Note: Non washable
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
LQGXVWULDOSDQDVRQLFFRPDFH
1
© Panasonic Corporation 2019
ANCTB16E 201903-Fd
Light Touch Switches/EVPBA
■ Dimensions in mm (not to scale)
EVPBA
(Embossed Taping)
General dimension tolerance : ± 0.1
( )dimensions are reference dimensions.
1.3
2.6
(Without the remainder of the gate)
3.5
3
A'
A
(φ0.7)
(Push plate)
A
A'
(0.04)
0.35
0.38
0.58
Circuit diagram
A
A'
2- 1.5
3.8
2.6
Land pattern plan
Soldering thicknes t=0.08±0.01
The opening ratio of the solder stencil to a
land pattern shall be 70%
If you design different stencil mask and land
pattern, or apply different soldering thickness
compared with our recommended pattern as
described above, please ask us in advance.
Part Numbers
Operating Force
Height
Operating Life
EVPBABA3A
1.8 N
0.58 mm
300,000 cycles
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Panasonic Corporation Electromechanical Control Business Division
industrial.panasonic.com/ac/e/
2
© Panasonic Corporation 2019
ANCTB16E 201903-Fd
Light Touch Switches/EVPBA
■ Recommended Reflow Soldering Conditions
Operation Top (°C)
MAX.
260
Fan or Normal Temp.
230
180
150
(Normal Temp.)
90±30
40±10
Soldering Time (s)
Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch
to make sure the both temperatures are withiin the specification.
If even one of them is out of the specifi cations, please adjust.
● Embossed Carrier Taping
Tape width=12.0 mm (A=12.0 mm)
I
F
E
φG
J
B
D
H
K
A
C
Taping condition : Lack of products in the middle of taping should be
one MAX, but total quantity specified in the
specifications should be secured.
Peeling off strength of top tape : It should be within 0.2N to 1.0N at
165 degree in peeling off angle.
Joint of carrier tape : One joint per one reel may exist.
t
Tape running direction
Part No.
Height
EVPBA
0.58
A
B
C
12.0±0.3 1.75±0.10 5.5±0.1
D
E
F
4.0±0.1
4.0±0.1
2.0±0.1
G
H
I
J
K
1.5±0.3 3.75±0.20 2.85±0.20 0.8±0.2
(10.25)
Unit: mm
t
0.3
+0.15
-0.1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Panasonic Corporation Electromechanical Control Business Division
industrial.panasonic.com/ac/e/
3
© Panasonic Corporation 2019
ANCTB16E 201903-Fd
Requests to customers
Please refer to "the latest product specifications" when designing your product.
Requests to customers :
https://industrial.panasonic.com/ac/e/salespolicies/
Safety Precautions
When using our products, no matter what sort of equipment they might be used for, be sure to
confirm the applications and environmental conditions with our specifications in advance.
Please contact ..........
Electromechanical Control Business Division
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2019
ANCTB16E-1 201903-Fd
Specifications are subject to change without notice.
很抱歉,暂时无法提供与“EVPBABA3A”相匹配的价格&库存,您可以联系我们找货
免费人工找货