Light Touch Switches/EVPBL
2.8 mm×1.9 mm SMD Light Touch Switches
Type:
EVPBL
■ Features
● External dimensions: 2.8 mm×1.9 mm, Height 0.53 mm, 0.57 mm, 0.60mm
● High operability equipped with an actuator (push plate)
● IP67
■ Recommended Applications
● Operation switches for portable electronic equipments
(Mobile phone, Portable audio)
■ Explanation of Part Numbers(Standard specification only)
1
2
3
4
5
B
L
Product Code
Type
6
7
8
9
A
Operating
Force
10
11
12
0
0
0
Height
Packing unit
B 16,000 pcs.
F
20,000 pcs.
■ Specifications
Type
Snap action/Push-on type SPST
Rating
10 μA 2 V DC to 20 mA 15 V DC (Resistive load)
Contact Resistance
Electrical
500 mΩ max.
Insulation Resistance
Mechanical
Endurance
50 MΩ min. (at 100 V DC)
Dielectric With standing Voltage
250 V AC for 1 minute
Bouncing
10 ms max. (ON, OFF)
1.6 N, 2.25 N, 3.0N
Operating Force
Travel
0.15 mm
Operating Life
Protective Structure
300,000 cycles min.
IP67(*1)
Operating Temperature
–40 °C to +85 °C
–40 °C to +85 °C (Bulk)
–20 °C to +60 °C (Taping)
Storage Temperature
Minimum Quantity/Packing Unit
Dust resistance : 4 types of talc 8 h,
Water resistance : Immersion depth 1 m 30 min.
1.6 N, 2.25 N : 16,000 pcs. Embossed Taping (Reel Pack)
3.0 N : 20,000 pcs. Embossed Taping (Reel Pack)
1.6 N, 2.25 N : 80,000 pcs.
3.0 N : 100,000 pcs.
Quantity/Carton
Note: Non washable
(*1) IP 67 : Switch shall not be operated during test.
Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function.
However, IP67 shall be guaranteed under single product state,
then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage.
So, please ask us in advance, if the switch is applied to important usage for water and dust resistant.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2020.02
LQGXVWULDOSDQDVRQLFFRPDFH
1
© Panasonic Corporation 2020
ANCTB104E 202002
Light Touch Switches/EVPBL
■ Dimensions in mm (not to scale)
EVPBL
(Embossed Taping)
General dimension tolerance : ±0.1
( ) dimensions are reference dimensions.
(Without the remainder of the
molding gate and the film)
This reference specifications are subject to change.
H
(0.35)
A'
B
B'
1.9±0.15
A
(φ0.85)
2.8±0.15
2-3(Terminal)
A
0.1max.
0.1max.
2-1.5
2-0.75
(2-2.18)
B
A
B'
This product is designed to be smaller than the
conventional type, which lowered the film peel off
strength. Therefore please avoid to apply force to
a push plate from side, or/and
avoid set-knob to touch push plate during insertion
to a set-case.
:Recommended land pattern area.
:No soldering area.
A'
No soldering
0.6
1.72
(1.9)
Circuit Diagram
Molding gate
Solder thickness t=0.08±0.01
(1.8)
B
B'
2.14
3.4
Part Numbers
A'
• Any land pattern or via holes shall not be
provided at
area.
• If it's necessary to design land pattern or
via holes at
area.
please apply resist to them to protect their
metal part completely.
• If their metal parts are not protected
completely,short circuit failure may occur
by solder ball.
• Beside, there should be convexoconcave by
designing additional pattern,
it may cause swith tilt, influence on
solder-ability or flux intrusion
after reflow soldering.
• Therefore, please study any influence of
additional land pattern or via holes at
area in advance.
Operating Force
H=Height
Operating Life
EVPBL2A1B000
1.6 N
0.53 mm
300,000 cycles
EVPBL9A2B000
2.25 N
0.57 mm
300,000 cycles
EVPBL5A8F000
3.0 N
0.60 mm
300,000 cycles
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Panasonic Corporation Electromechanical Control Business Division
industrial.panasonic.com/ac/e/
2
© Panasonic Corporation 2020
ANCTB104E 202002
Light Touch Switches/EVPBL
■ Recommended Reflow Soldering Conditions
Switch Top(°C)
MAX.
245
Cooling
220
180
150
*Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch
to make sure the both temperatures are within the specification.
If even one of them is out of the specifications,please adjust.
(Normal
condition)
90±30
40±10
Time
● Carrier tape
F
E
H
φG
J
I
K
A
C
B
D
t
Take out direction
Taping condition : Lack of products in the middle of taping should be one MAX.
but total quantity specified in the specifications
should be secured.
Peeling off strength of top tape : It should be within 0.2N to 1.0N at 165 degree
in peeling off angle.
Joint of carrier tape : One joint per one reel may exist.
Unit: mm
Part No.
EVPBL
Height
0.53
0.57
0.60
A
B
C
D
E
F
G
H
I
J
K
t
8.0±0.3
1.75±0.1
3.5±0.1
4.0±0.1
4.0±0.1
2.0±0.1
1.5 ー0
2.2±0.2
3.4±0.2
0.7±0.2
(6.25)
0.3±0.1
+0.1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Panasonic Corporation Electromechanical Control Business Division
industrial.panasonic.com/ac/e/
3
© Panasonic Corporation 2020
ANCTB104E 202002
Requests to customers
Please refer to "the latest product specifications" when designing your product.
Requests to customers :
https://industrial.panasonic.com/ac/e/salespolicies/
Safety Precautions
When using our products, no matter what sort of equipment they might be used for, be sure to
confirm the applications and environmental conditions with our specifications in advance.
Please contact ..........
Electromechanical Control Business Division
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2020
ANCTB104E 202002
Specifications are subject to change without notice.
很抱歉,暂时无法提供与“EVPBL2A1B000”相匹配的价格&库存,您可以联系我们找货
免费人工找货