HP3-M-AC220V

VDE 2c, 3c 10 AMP POWER RELAY HP-RELAYS 25 .984 36 1.417 FEATURES • Interchangeable with existing models • Long life and high reliability • High contact capacity up to 10 A 250 V AC • Available with plug-in/solder and quick-connect terminals 44.5 1.752 mm inch SPECIFICATIONS (at 20°C 68°F) Contacts Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1 A) Contact material Rating Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "initial breakdown voltage" section *2 Detection current; 10 mA *3 Excluding contact bounce time *4 Half-wave pulse of sine wave: 11ms; detection time: 10µs *5 Half-wave pulse of sine wave: 6ms *6 Detection time: 10µs *7 Refer to 5. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT (Page 61). Characteristics (at 60 Hz, 20°C 68°F) 2 Form C 3 Form C 4 Form C 15 mΩ Silver Silver alloy Maximum operating speed Initial insulation resistance*1 Between open contacts Breakdown Between contact sets voltage*2 Between contact and coil Operate time*3 (at nominal voltage) Release time (without diode)*3 (at nominal voltage) Temperature rise Functional*4 Shock resistance Destructive*5 Functional*6 Vibration resistance Destructive Conditions for opera- Ambient tion, transport and temp. storage*7 (Not freezing and condensing at low Humidity temperature) Unit weight 2 Form C 3 Form C 4 Form C 20 cpm more than 100 MΩ at 500 V DC 1,000 2,000 1,000 Vrms Vrms Vrms 1,500 2,000 1,500 Vrms Vrms Vrms 1,500 2,000 1,500 Vrms Vrms Vrms Approx. 15 ms Approx. 15 ms Approx. 25 ms Approx. 25 ms Nominal switching capacity 10 A 250 V AC (resistive) Max. 65°C 98 m/s2 {10 G} 980 m/s2 {100 G} 58.8 m/s2 {6 G}, 10 to 55 Hz at 1 mm double amplitude 117.6 m/s2 {12 G}, 10 to 55 Hz at 2 mm double amplitude –50°C to +40°C –58°F to +104°F 5 to 85% R.H. Approx. 60g 2.12 oz Approx. 100g 3.53 oz Approx. 125g 4.41 oz LIFE DATA Contact rating and expected life For AC load type Voltage Load Electrical life 125 V AC Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) — — 10 A 7.5 A 5A 3A 1A 0.7 A Mechanical life 250 V AC Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) 10 A 7.5 A 7.5 A 5A 3A 2A 0.6 A 0.4 A Expected life (min. operations) 2×105 5×105 1×106 2×106 1×107 Current Note: When the electromagnet or exciting coil (Solenoid, etc.) is the load, the value of motor or lamp load is applicable. 411 HP Contact rating and expected life For DC load type Voltage Load Electrical life 24 V DC Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) — 7A 7.5 A 5A 5A 3A 1A 0.6 A Mechanical life 125 V DC Resistive (cosϕ ] 1) Inductive (cos ϕ ] 0.4) — — 0.5 A 0.4 A 0.3 A 0.2 A 0.1 A 0.06 A Expected life (min. operations) 2×105 5×105 1×106 2×106 1×107 Current Life curve 1,000 Operations, ×104 900 800 700 600 500 400 300 200 125 V A Mechanical life more than 10,000,000 operations 100 0 0 VA Cc C cosϕ =1 Notes: 1. For DC inductive loads, use an arc suppressing circuit. 2. When used under a DC load operating at high repetition rate with considerable arcing, corrosion of the contacts and/or the contact blades is likely to occur. When using the relay under conditions of high temperature, humidity or high repetition rate, it is suggested that the relay cover be removed to facilitate extended operation. 10 TYPICAL APPLICATIONS HP relays enjoy wide use in various applications, particularly in automation controls and remote controls. Applications include: Industrial machinery Machine tool Food processing packing machines Office equipment Coin operate devices Home appliances Transportation Communication and measuring devices Amusement devices ORDERING INFORMATION Ex. Contact arrangement 2: 2 Form C 3: 3 Form C 4: 4 Form C HP 3 M AC240V Coil voltage AC 6, 12, 24, 48, 115, 220, 240 V DC 6, 12, 24, 48, 110 V Terminal Nil: Standard plug-in terminal M: Direct mounting (3 Form C only) TM: Top mounting (2 Form C only) L: Lamp wired, standard plug-in terminal (Notes) 1. For UL/CSA or VDE recognized types, add suffix UL/CSA or VDE (HP2-TM type VDE application under way) 2. Standard packing Carton: 50 pcs. Case: 200 pcs. 3. UL/CSA approved type is standard. TYPES AND COIL DATA 1. Standard plug-in terminal type (without lamp wired) DC TYPES at 20°C 68°F Type Part No. HP2-DC6V HP2-DC12V HP2-DC24V HP2-DC48V HP2-DC110V HP3-DC6V HP3-DC12V HP3-DC24V HP3-DC48V HP3-DC110V HP4-DC6V HP4-DC12V HP4-DC24V HP4-DC48V HP4-DC110V Nominal coil voltage, V DC 6 12 24 48 110 6 12 24 48 110 6 12 24 48 110 Pick-up voltage, V DC (max.) 4.8 9.6 19.2 38.4 88 4.8 9.6 19.2 38.4 88 4.8 9.6 19.2 38.4 88 Drop-out voltage, V DC (min.) 0.9 1.8 3.6 7.2 16.5 0.9 1.8 3.6 7.2 16.5 0.9 1.8 3.6 7.2 16.5 Max. allowable voltage, V DC 6.6 13.2 26.4 52.8 121 6.6 13.2 26.4 52.8 121 6.6 13.2 26.4 52.8 121 Coil resistance, Ω (±10%) 25 110 440 1,800 7,300 24 100 400 1,560 7,450 22 95 380 1,500 7,000 Nominal coil current, mA 240 109 54.5 26.7 15.0 250 120 60 31 14.9 273 127 63 32 15.7 Nominal operating power, W 1.5 1.3 1.3 1.3 1.7 1.5 1.4 1.4 1.5 1.6 1.6 1.5 1.5 1.5 1.7 2 Form C 3 Form C 4 Form C 25 os ϕ = 1 5 Load current, A 412 HP AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F Type Part No. HP2-AC6V HP2-AC12V HP2-AC24V HP2-AC48V HP2-AC115V HP2-AC220V HP2-AC240V HP3-AC6V HP3-AC12V HP3-AC24V HP3-AC48V HP3-AC115V HP3-AC220V HP3-AC240V HP4-AC6V HP4-AC12V HP4-AC24V HP4-AC48V HP4-AC115V HP4-AC220V HP4-AC240V Nominal coil voltage, V AC 6 12 24 48 115 220 240 6 12 24 48 115 220 240 6 12 24 48 115 220 240 Pick-up voltage, V AC (max.) 4.8 9.6 19.2 38.4 92 176 192 4.8 9.6 19.2 38.4 92 176 192 4.8 9.6 19.2 38.4 92 176 192 Drop-out voltage, V AC (min.) 1.8 3.6 7.2 14.4 34.5 66 72 1.8 3.6 7.2 14.4 34.5 66 72 1.8 3.6 7.2 14.4 34.5 66 72 Max. allowable voltage, V AC 6.6 13.2 26.4 52.8 126.5 242 264 6.6 13.2 26.4 52.8 126.5 242 264 6.6 13.2 26.4 52.8 126.5 242 264 Inductance, H 0.049 0.190 0.776 3.106 15.83 57.90 66.26 0.030 0.119 0.475 1.899 10.36 39.32 44.05 0.019 0.077 0.309 1.292 6.953 26.57 29.75 Nominal coil current, mA 310 160 78 39 18 9.5 9.0 520 260 130 65 28.5 14.2 13.9 800 400 200 95 42 21 20.5 Nominal operating power, VA 1.9 1.9 1.9 1.9 2.1 2.1 2.2 3.1 3.1 3.1 3.1 3.3 3.1 3.3 4.8 4.8 4.8 4.6 4.8 4.6 4.9 2 Form C 3 Form C 4 Form C NOTES 1. The range of coil current for AC relays is ±15% (60 Hz). For DC relays it is ±10% at 20°C, 68°F. 2. The HP relay will operate in a range from 80% to 110% of the nominal coil voltage. It is, however, recommended that the relay be used in the range of 85% to 110% of the nominal coil voltage, with the temporary voltage variation taken into consideration. 3. When the operating voltage of AC re- lays drops below 80% of the nominal coil voltage, the relay will generate a considerable amount of heat which is not recommended for maximum efficiency. 4. The coil resistance of DC types is the measured value of the coil at a temperature of 20°C 68°F. If the coil temperature changes by ±1°C, the measured value of the coil resistance should be increased or decreased by 0.4%. 5. For applications from 220 V to 240 V DC, connect a resistor in series with the relay coil. See chart for resistor values. Voltage 220 V DC 240 V DC 2 Form C 3 Form C 4 Form C 7.3 kΩ 7.45 kΩ 7 kΩ (5 W) (5 W) (5 W) 8.7 kΩ 8.8 kΩ 8.3 kΩ (5 W) (5 W) (5 W) 2. Standard plug-in terminal type (with lamp wired) DC TYPES at 20°C 68°F Type Part No. HP2-L-DC6V HP2-L-DC12V HP2-L-DC24V HP2-L-DC48V HP2-L-DC110V HP3-L-DC6V HP3-L-DC12V HP3-L-DC24V HP3-L-DC48V HP3-L-DC110V HP4-L-DC6V HP4-L-DC12V HP4-L-DC24V HP4-L-DC48V HP4-L-DC110V Nominal coil Pick-up voltage, voltage, V DC V DC (max.) 6 12 24 48 110 6 12 24 48 110 6 12 24 48 110 4.8 9.6 19.2 38.4 88 4.8 9.6 19.2 38.4 88 4.8 9.6 19.2 38.4 88 Drop-out voltage, V DC (min.) 0.9 1.8 3.6 7.2 16.5 0.9 1.8 3.6 7.2 16.5 0.9 1.8 3.6 7.2 16.5 Max. allowable voltage, V DC 6.6 13.2 26.4 52.8 121 6.6 13.2 26.4 52.8 121 6.6 13.2 26.4 52.8 121 Coil resistance, Ω (±10%) 25 110 440 1,800 7,300 24 100 400 1,560 7,450 22 95 380 1,500 7,000 Nominal coil current, mA 240 109 54.5 26.7 15.0 250 120 60 31 14.9 273 127 63 32 15.7 Nominal operating power, W 1.5 1.3 1.3 1.3 1.7 1.5 1.4 1.4 1.5 1.6 1.6 1.5 1.5 1.5 1.7 2 Form C LED Neon lamp 3 Form C LED Neon lamp 4 Form C LED Neon lamp 413 HP AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F Type Part No. HP2-L-AC6V HP2-L-AC12V HP2-L-AC24V HP2-L-AC115V HP2-L-AC220V HP2-L-AC240V HP3-L-AC6V HP3-L-AC12V HP3-L-AC24V HP3-L-AC115V HP3-L-AC220V HP3-L-AC240V HP4-L-AC6V HP4-L-AC12V HP4-L-AC24V HP4-L-AC115V HP4-L-AC220V HP4-L-AC240V Nominal coil voltage, V AC 6 12 24 115 220 240 6 12 24 115 220 240 6 12 24 115 220 240 Pick-up voltage, V AC (max.) 4.8 9.6 19.2 92 176 192 4.8 9.6 19.2 92 176 192 4.8 9.6 19.2 92 176 192 Drop-out voltage, V AC (min.) 1.8 3.6 7.2 34.5 66 72 1.8 3.6 7.2 34.5 66 72 1.8 3.6 7.2 34.5 66 72 Max. allowable voltage, V AC 6.6 13.2 26.4 126.5 242 264 6.6 13.2 26.4 126.5 242 264 6.6 13.2 26.4 126.5 242 264 Inductance, H 0.049 0.190 0.776 15.83 57.90 66.26 0.030 0.119 0.475 10.36 39.32 44.05 0.019 0.077 0.309 6.953 26.57 29.75 Nominal coil current, mA 310 160 78 18 9.5 9.0 520 260 130 28.5 14.2 13.9 800 400 200 42 21 20.5 Nominal operating power, VA 1.9 1.9 1.9 2.1 2.1 2.2 3.1 3.1 3.1 3.3 3.1 3.3 4.8 4.8 4.8 4.8 4.6 4.9 LED 2 Form C Neon lamp LED 3 Form C Neon lamp LED 4 Form C Neon lamp 3. Top Mounting (TM) and direct mounting (M) type DC TYPES at 20°C 68°F Type Part No. Nominal coil Pick-up voltage, voltage, V DC V DC (max.) 6 12 24 48 110 6 12 24 48 110 4.8 9.6 19.2 38.4 88 4.8 9.6 19.2 38.4 88 Drop-out voltage, V DC (min.) 0.9 1.8 3.6 7.2 16.5 0.9 1.8 3.6 7.2 16.5 Max. allowable voltage, V DC 6.6 13.2 26.4 52.8 121 6.6 13.2 26.4 52.8 121 Coil resistance, Ω (±10%) 25 110 440 1,800 7,300 24 100 400 1$B!"(J560 7,450 Nominal coil current, mA 240 109 54.5 26.7 15.0 250 120 60 31 14.9 Nominal operating power, W 1.5 1.3 1.3 1.3 1.7 1.5 1.4 1.4 1.5 1.6 HP2-TM-DC6V HP2-TM-DC12V 2 Form C HP2-TM-DC24V Top Mounting Type (TM) HP2-TM-DC48V HP2-TM-DC110V HP3-M-DC6V HP3-M-DC12V 3 Form C HP3-M-DC24V Direct Mounting Type (TM) HP3-M-DC48V HP3-M-DC110V AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F Type Part No. HP2-TM-AC6V HP2-TM-AC12V HP2-TM-AC24V HP2-TM-AC48V HP2-TM-AC115V HP2-TM-AC220V HP2-TM-AC240V HP3-M-AC6V HP3-M-AC12V HP3-M-AC24V HP3-M-AC48V HP3-M-AC115V HP3-M-AC220V HP3-M-AC240V Nominal coil voltage, V AC 6 12 24 48 115 220 240 6 12 24 48 115 220 240 Pick-up voltage, V AC (max.) 4.8 9.6 19.2 38.4 92 176 192 4.8 9.6 19.2 38.4 92 176 192 Drop-out voltage, V AC (min.) 1.8 3.6 7.2 14.4 34.5 66 72 1.8 3.6 7.2 14.4 34.5 66 72 Max. allowable voltage, V AC 6.6 13.2 26.4 52.8 126.5 242 264 6.6 13.2 26.4 52.8 126.5 242 264 Inductance, H 0.049 0.190 0.776 3.106 15.83 57.90 66.26 0.030 0.119 0.475 1.899 10.36 39.32 44.05 Nominal coil current, mA 310 160 78 39 18 9.5 9.0 520 260 130 65 28.5 14.2 13.9 Nominal operating power, VA 1.9 1.9 1.9 1.9 2.1 2.1 2.2 3.1 3.1 3.1 3.1 3.3 3.1 3.3 2 Form C Top Mounting Type (TM) 3 Form C Direct Mounting Type (M) 414 HP 4. Direct mounting (with lamp wired) type DC TYPES Type 3 Form C Neon lamp Part No. HP3-ML-DC110V Nominal coil Pick-up voltage, voltage, V DC V DC (max.) 110 88 Drop-out voltage, V DC (min.) 16.5 Max. allowable voltage, V DC 121 Coil resistance, Ω (±10%) 7,450 Nominal coil current, mA 14.9 Nominal operating power, W 1.6 AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F Type Part No. HP3-ML-AC115V HP3-ML-AC220V HP3-ML-AC240V Nominal coil Pick-up Drop-out voltage, voltage, voltage, V AC V AC (max.) V AC (min.) 115 V 220 V 240 V 92 176 192 34.5 66 72 Max. allowable voltage, V AC 126.5 242 264 Inductance, H 10.36 39.32 44.05 Nominal coil current, mA 28.5 14.2 13.9 Nominal operating power, VA 3.3 3.1 3.3 3 Form C Neon lamp LAMP-WIRED RELAYS Specifications Life of neon lamp....continuous: more than 25,000 hours (more than 3 years) on/off = 1: more than 6 years Life of LED..............continuous: more than 50,000 hours (more than 5.5 years) on/off = 1: more than 100,000 hours (more than 11 years) NEON LAMP LED Variation Type Coil Voltage AC 6V 12 V 24 V — 115 V 220 V 240 V DC 6V 12 V 24 V 48 V 110 V — — HP2-L HP3-L HP3-ML HP4-L LED (Light emitting diode) Neon lamp Notes: 1. AC 48 V type is not available for lamp wiring. Circuit diagrams Neon lamp type LED type Operating current of LED Coil Voltage DC 6V DC 12V DC 24V DC 48V AC 6V AC 12V AC 24V Operating current of LED DC 6.4 mA DC 5.7 mA DC 4.7 mA DC 4.5 mA AC 10.5 mA AC 9.0 mA AC 7.7 mA Terminal No. Type HP2-L Polarity (+) 7 (–) 2 Notes: 1. Pay attention to the polarity of coil See circuit diagram (LED type only). (DC type) HP3-L HP3-ML 10 2 HP4-L 10 1 Notes: 1. Operating current of relays should be increased by the value of LED operating current. Please refer the table. Operating current of neon lamp is approx. 0.3 mA to 0.4 mA. 2. To use the HP relay in the inductive load circuit, the contact protection circuit is recommended. 415 HP ACCESSORIES Please refer to "MOUNTING METHODS" for further information. UL, CSA recognized except BRACKET and INSERTING PLATE. HP Relay Solder terminal socket for rectangular hold boring (with hold-down clip) HP2-SRS Screw terminal socket for DIN rail assembly (with hold-down clip) HP2-SFD For HP2, HP4 HP-BRACKET for direct mounting HP2 (UL, CSA, VDE) HP3-SRS (UL, CSA) HP3-SFD HP3 HP INSERTION PLATE for P/C board mounting (UL, CSA, VDE) HP4-SRS (UL, CSA, VDE) HP4-SFD HP4 (UL, CSA) (UL, CSA) DIMENSIONS AND WIRING DIAGRAM HP2 (2 Form C) Plug-in terminal types 0.5 .020 5 8 5 .197 .315 .197 mm inch 44 1.732 51 2.008 25 .984 15 .591 0.8 .031 Circuit diagram 5.26 .207 9.5 .374 36 7.5 .295 1.417 5.8 .228 5.3 .209 5.26 .207 10 .394 Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 Accepts Faston 205 416 HP HP2-SRS (with hold-down clip) Optimum space-saving panel cut-out. Can be mounted from either the front or the rear of the panel. Front surface-mounting 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE mm inch HOLD-DOWN CLIP 5 .197 22 .866 5 .197 6.2 .244 4.1 .161 30 1.181 1.0 .039 6 .236 13 .512 48±0.2 38 1.890 ±.008 56 1.496 2.205 33 1.299 24 +0.1 –0 .945 +.004 –0 48±0.5 34 +1 1.890±.020 –0 1.339 +0.39 –0 57.9±3 2.280±.118 HP RELAY HP SOCKET 4 mm SCREW SPRING WASHER 13 .512 PANEL Rear surface-mounting 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE 56.9±3 2.240±.118 39 48±0.5 1.535 1.890±.020 HOLD-DOWN CLIP 5.5 .217 HP RELAY HP SOCKET 4 mm SCREW SPRING WASHER Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 14 .551 31 1.220 PANEL HP2-SFD (with hold-down clip) Front wiring in restricted space 10±0.2 .394±.008 HP2 RELAY HOLD DOWN CLIP 23.8±0.6 .937±.024 22±0.2 .866±.008 Mounting dimensions 12 .472 2-M4 .157 SCREW HOLE or 22±0.2 4.2±0.1 .165±.004 DIA. HOLE .866±.008 5.8±0.2 .228±.008 7.5±0.2 .295±.008 9.5±0.2 .374±.008 0.6±0.15 .024±.006 58±1 2.283±.039 ±1 1 69±±.039 36 2.717 1.417±.039 80±1 3.150±.039 35.4±0.5 1.394±.020 80 69±0.5 2.717±.020 3.150 6±0.3 .236±.012 15±0.2 .591±.008 22±0.6 .866±.024 4.1±0.3 .161±.012 10±0.6 .394±.024 ±0.6 33.8 1.331±.024 37.9±0.6 1.492±.024 Max. 85 3.346 Max. 89 3.504 Installation screw block (installation screw, hexagonal nut, spring washer) 4 .157 30 30 1.181 1.181 Panel hole dimensions for side-by-side installation Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 Note: Hold down clip and installation screw block are included in package. HP2-TM (2 Form C) Top mounting types 2.8 .110 35.7 1.406 46.8 1.843 52.3 2.059 4 mm SCREW or 8-32 NC-2 SCREW SCREW WASHER 7 .276 5.5 .217 24.7 .972 25 .984 15 .591 35.7 1.406 0.8 .031 PANEL 0.8 .031 Circuit diagram Mounting dimensions 9.5 .374 45.5 58 1.791 2.283 7.5 .295 5.8 .228 5.3 .209 2.25R .089R 45.5 1.791 Accepts Faston 205 5.26 .207 4.5 10 .177 .394 5.26 .207 Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 4.5±0.1 DIA. HOLE or 4 mm SCREW HOLE .117±.004 DIA. HOLE 2 .079 30 1.181 417 HP HP3 (3 Form C) Plug-in terminal types 38 1.496 0.5 .020 58 5 .197 .315 .197 mm inch 44 1.732 3 .118 5 .197 38 1.496 11 11 .433 .433 4.75 .187 0.5 .020 2 .079 5.75 .226 5.5 .217 8.5 36 4 .335 1.417 .157 7.65 4.1 .301 .161 7 .276 36 1.417 Circuit diagram Accepts Faston 187 2 .079 Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 HP3-SRS (with hold-down clip) Optimum space-saving panel cut-out. Can be mounted from either the front or the rear of the panel. 22.23 .875 6.2 .244 3.5 .138 48±0.2 1.890±.008 38 56 1.496 2.205 0.6 7.65 .024 .301 5.5 .217 30 1.181 8.5 .335 2.75 .108 8 .315 14.5 .571 Front surface-mounting 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE 3.5 .138 5 .197 42.95 22 1.691 .866 5 .197 4.1 .161 31 +1 –0 1.220 +0.39 –0 48±0.5 1.890±.020 40±0.3 1.575±.012 HOLD DOWN CLIP 31 +1 –0 1.220 +.039 –0 HP RELAY 52±0.3 2.047±.012 Rear surface-mounting +0.2 4.2−0 dia. +.008 .165−0 dia. Lot No. 11 11 .433 .433 45 1.772 1 .039 5.5 .217 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE 3.5 .138 39 +1 –0 1.535 +.039 –0 48±0.5 1.890±.020 30 1.181 Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 46 +1 –0 1.811 +.039 –0 HP3-SFD (with hold-down clip) Front wiring in restricted space 22±0.2 .866±.008 HP3 RELAY HOLD DOWN CLIP 23.8±0.6 .937±.024 37 1.457 ±0.2 ±.008 Mounting dimensions 12 .472 37 1.457 ±0.2 ±.008 2-M4 .157 SCREW HOLE or 4.2±0.1 .165±.004 DIA. HOLE 5.5±0.2 .217±.008 8.5±0.2 .335±.008 ±0.2 7.65.008 .301± 1.75±0.15 .069±.006 58±1 2.283±.039 69±1 36±1 2.717±.039 1.417±.039 80±1 3.150±.039 35.4±0.5 1.394±.020 69±0.5 80 2.717±.020 3.150 37±0.6 1.457±.024 6±0.3 .236±.012 4.1±0.3 .161±.012 10±0.6 .394±.024 ±0.6 33.8 1.331±.024 37.9±0.6 1.492±.024 Max. 85 3.346 Max. 89 3.504 Installation screw block (installation screw, hexagonal nut, spring washer) 45 1.772 4 .157 45 1.772 Panel hole dimensions for side-by-side installation Note: Hold down clip and installation screw block are included in package. Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 418 HP HP3-M (3 Form C) Direct mounting types 38 1.496 16 .630 2.1R mm inch Mounting dimension 4.2 .165 5 .197 2.1R 44 60 1.732 2.362 73.5 2.894 11 7 .276 .433 20.5 .807 36 1.417 60 2.362 3 .118 4.2 .165 16 .630 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE 38 1.496 11 11 .433 .433 4.75 4.75 4.75 .187 .187 .187 2.5 2.5 .098 .098 0.5 .020 MIN. 2 .079 MIN. 40 1.575 Circuit diagram 5.75 .226 5.5 .217 8.5 .335 36 7.65 1.417 .301 4 mm SCREW or SPRING 8-32 NC-2 SCREW WASHER 0.5 2 .020 .079 0.5 .020 0.5 4.1 .020 .161 2 .079 Accepts Faston 187 73.5 44 1.732 60 2.894 2.362 7 .276 20.5 5 .807 11 .197 .433 Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 16 .630 38 1.496 36 1.417 HP4 (4 Form C) Plug-in terminal types 5 8 5 .197 .315 .197 0.5 .020 44 1.732 51 2.008 0.8 .031 50 1.969 40 1.575 10 .394 Circuit diagram 5.26 .207 36 1.417 9.5 .374 7.5 .295 5.8 .228 5.3 .209 25 .984 10 .394 10 .394 Accepts Faston 187 Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 419 HP HP4-SRS (with hold-down clip) Optimum space-saving panel cut-out. Can be mounted from either the front or the rear of the panel. mm inch Front surface-mounting 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE HOLD-DOWN CLIP 5 .197 22 .866 5 .197 4.1 .161 58 2.283 48±0.2 38 1.890 ±.008 56 1.496 2.205 6.2 .244 5.5 .217 33 1.299 48 +1 –0 34 +1 48±0.5 –0 1.339 1.890 +.039 ±.020 –0 53±3 2.087±.118 HP RELAY HP SOCKET 4 mm SCREW SPRING WASHER 13 .512 +.039 –0 PANEL Rear surface-mounting 1.0 .039 6 .236 13 .512 4.2±0.1 DIA. HOLE or 4 mm SCREW HOLE .165±.004 DIA. HOLE 52±3 2.047±.118 HOLD-DOWN CLIP HP RELAY HP SOCKET 4 mm SCREW SPRING WASHER Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 39 +1 48±0.5 –0 1.535 1.890 +.039 ±.020 –0 14 .551 58 +1 –0 2.284 +.039 –0 PANEL HP4-SFD (with hold-down clip) Front wiring in restricted space. Two HP2 relays can be mounted in one socket. 10±0.2 .394±.008 25±0.1 .984±.004 10±0.2.008 .394± HOLD DOWN CLIP HP4 RELAY 58±1 2.283±.039 5.8 .228 7.5±0.2 .295±.008 9.5±0.2 .374±.008 0.6±0.15 .024±.006 ±0.2 ±.008 Mounting dimensions 23.8 .937 ±0.6 ±.024 53±0.2 2.087±.008 12 .472 2-M4 .157 SCREW HOLE or 4.2±0.1 .165±.004 DIA. HOLE 53±0.2 2.087±.008 69±1 2.717±.039 36±1 1.417±.039 80±1 3.150±.039 35.4±0.5 1.394±.020 69±0.5 2.717±.020 80 3.150 15±0.2 15±0.2 .591±.008 .591±.008 53±0.6 2.087±.024 6±0.3 .236±.012 4.1±0.3 .161±.012 10±0.6 .394±.024 33.8±0.6 1.331±.024 37.9±0.6 1.492±.024 Max. 85 3.346 Max. 89 3.504 Installation screw block (installation screw, hexagonal nut, spring washer) 61 2.402 4 .157 61 2.402 Panel hole dimensions for side-by-side installation Note: Hold down clip and installation screw block are included in package. Dimension : Max. 2mm .079 inch: 2 to 9mm .079 to .354 inch: 9 to 20mm .354 to .787 inch: Min. 20mm .787 inch: General tolerance ±0.2 ±.008 ±0.5 ±.020 ±1.0 ±.039 ±1.5 ±.059 ACCESSORIES for HP2 and HP4 types HP Bracket (with 2 screws, 2 washers) The HP Bracket is used for mounting HP2 relays and HP4 relays directly to the panel. It facilitates soldering or quick connections with Faston 205 tab 0.8 mm .031 inch. Notes: 1. This bracket is unavailable for UL, CSA and VDE applications. 2. When using the special bracket, it is recommended to use the screws and washers called out in the chart in the next page in order to eliminate any possible damage to the relay coil. Mounting methods (a) Remove the M3 × 7 screw (red colored) fixed to the relay, and place the bracket on the relay with the attaching M3 × 7 screw (blue colored) and the spring washer. (b) Use the additional M3 × 7 screw and washer for attaching the bracket to the panel. 8 .315 For the HP4 type relay two brackets are used 14 .551 4 .158 90°±3° 14 .55120 23 .906 2 .079 8.5 .335 1 .039 3 DIA. HOLE .118 DIA. HOLE .787 3.5 DIA. HOLE .138 DIA. HOLE Keying tab. 420 HP Thickness of a special bracket A suitable screw A suitable washer 1.0 mm (.039 inch) M3 × 7-M3 × 8 for M3 Screw Millimeter 3mm .118inch diameter 7mm .276inch length M 3 1.6 mm (.063 inch) M3 × 8 for M3 × 7 2.0 mm (.079 inch) M3 × 8-M3 × 10 for M3 Dimensions and mounting method HP2 4.5 DIA. HOLE .177 DIA. HOLE 25 .984 4.5 DIA. HOLE .177 DIA. HOLE 50 1.969 8.5 .335 51 2.008 20 .787 7 .276 25 .984 MIN. 26 1.024 25 .984 mm inch HP4 3 mm SCREW 42 1.654 BRACKET PANEL KEYING TAB 3 mm SCREW 27 1.063 51 2.008 1. Rear-surface mounting 8.5 .335 51 2.008 20 .787 7 .276 MIN. 26 1.024 3.2 DIA. HOLE .126 DIA. HOLE 25 .984 3.2 DIA. HOLE .126 DIA. HOLE 50 1.969 44 1.732 3 mm SCREW 2. Front-surface mounting 44 1.732 42 1.654 3 mm SCREW 13 .512 14.5 .571 MIN. 26 1.024 4.5 DIA. HOLE .177 DIA. HOLE 13 .512 14.5 .571 25 .984 KEYING TAB MIN. 26 1.024 25 .984 28.5 1.122 PANEL BRACKET 44 1.732 51 2.008 4.5 DIA. HOLE .177 DIA. HOLE HP Inserting Plate for HP2 and HP4 types 1. HP inserting plate is used for mounting 2. If adjustment by soldering is not suitHP2 and HP4 relays on a printed board to able, bore 1/8" diameter hole on the printadjust the length of the terminals. ed circuit board and mount the relay with a M3 × 10 screw. The chart to the right suggests the proper screws for different printed circuit boards. 3. Two plates are used for the HP4 type relay. Thickness of P/C board 1.0 mm .039 inch 1.2 mm .047 inch Suitable screw M3 × 10 M3 × 10 PC board pattern 3 .118 15 .591 8 .315 4 DIA. HOLE .157 DIA. HOLE 16 .630 36 1.417 7.3 .287 HP2 3 .118 4.5 .177 1.0 .039 7.5 .295 9.5 .374 8.9 .350 15 .591 3.2 DIA. HOLE .126 DIA. HOLE 10 .394 5.8 .228 5.8 .228 7.5 .295 9.5 .374 8.9 .350 1.0 .039 10 .394 HP4 25 .984 5.8 .228 5.8 .228 46 1.811 HP INSERTION PLATE PC BOARD 15 .591 5 .197 10 .394 16.5 .650 25 .984 2 .079 15 .591 3.2 DIA. HOLE .126 DIA. HOLE Please refer to the above second instruction. Tolerance: ±0.1 ±.004 For Cautions for Use, see Relay Technical Information (Page 48 to 76). 9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, 421 Ltd. Go To Online Catalog