213
FIBER
SENSORS
Digital Laser Sensor
Amplifier-separated
LS-400 SERIES
Related Information
LASER
SENSORS
■■General terms and conditions.............. F-3
■■SC-GU3......................................... P.971~
■■About laser beam........................ P.1593~
■■Selection guide.............................. P.169~
■■Glossary of terms / General precautions. ...... P.1549~ / P.1552~
■■Korea’s S-mark.............................. P.1602
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
Recognition
(Excluding LS-403)
AREA
SENSORS
Conforming to
FDA regulations
(LS-H□F only)
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
These products are Class 2
(LS-H□-A: Class 1) laser in
compliance with IEC / JIS
/ GB standards and FDA*
regulations Do not look at the
laser beam directly or through
optical system such as a lens.
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
*This product complies with 21 CFR 1040.10 and
1040.11 Laser Notice No. 50, dated June 24,
2007, issued by CDRH (Center for Devices and
Radiological Health) under the FDA (Food and Drug
Administration).
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
panasonic.net/id/pidsx/global
Test input
User-friendly, high precision
laser sensing!
Timer
PNP output
type available
Light intensity
monitor
Interference Automatic
prevention sensitivity setting
We offer 6 types of laser sensor heads for various applications
RF-230
FA COMPONENTS
MACHINE VISION
SYSTEMS
A line width of approx. 240 mm
9.449 in (typical) at a 1,000 mm
39.370 in sensing distance
UV CURING
SYSTEMS
A spot size of approx. 10 × 8 mm 0.394 × 0.315 in
at a 3 m 9.843 ft sensing distance (Note 2)
Selection
Guide
Amplifier
Built-in
Amplifierseparated
Easy-to-use sealing-type
reflective tape available
A spot diameter of approx.
ø1 mm ø0.039 in at a 1 m
3.281 ft sensing distance (Note 1)
RF-31
RF-33
Long sensing range
coaxial retroreflective type
LS-H92
Coaxial retroreflective type
Connector type
LS-401/401P/403
RF-330
5m
(16.404 ft)
A spot diameter of approx. ø1 mm
ø0.039 in at a 1,000 mm 39.370 in
sensing distance (Note 1)
Long sensing range line
reflective type LS-H22
Amplifiers
RF-330
7m
(22.966 ft)
RF-310
LS-500
30 m
(98.425 ft)
Compact
reflector
RF-310
A line width of approx. 115 mm
4.528 in (typical) at a 500 mm
19.685 in sensing distance
LS-400
Certified
(Some models only)
A spot diameter of approx. ø1 mm ø0.039 in
at a 1 m 3.281 ft sensing distance (Note 1)
A spot diameter of approx. ø0.2 mm ø0.008 in
at a 50 mm 1.969 in sensing distance (Note 1)
LS-H91
500 mm
(19.685 in)
Coaxial retroreflective type
LS-H91-A Class 1 type
Cable type (with external input)
LS-401-C2 / LS-401P-C2
1m
(3.281 ft)
Long sensing range
spot reflective type
LS-H21
Notes: 1) The spot diameter is a typical example. The measurement values given here
were determined with a center light intensity of 1/e2 (13.5 %).
2) This is the reference value from visual observation.
A spot diameter of approx. ø0.2
mm ø0.008 in at a 50 mm 1.969
in sensing distance (Note 1)
Long sensing range spot reflective type
LS-H21-A Class 1 type
Digital Laser Sensor
LS-400 SERIES
FIBER
SENSORS
APPLICATIONS
Detecting objects with a complex shape
Its linear sensing area enables more
stable detection of objects with complex
shapes.
LS-H22
Detecting the remaining amount of sheet rolls
The coaxial retroreflective sensor with a spot diameter
of approx. ø1 mm ø0.039 in (at a 1 m 3.281 ft sensing
distance), can measure amounts remaining on sheet rolls
with high precision.
Sheet rolls
Detecting electronic component pins
Because its spot shape can be adjusted in accordance
with the object, it can be easily set to detect even the
minutest object from a remote location.
Reflector
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
LS-H91
LS-H21
Transparent films
NOTE: T
he applications given in this catalog are examples for reference only. Stable sensing may not be possible under
certain setup conditions and environmental conditions, so be sure to check the actual sensor before use.
Long sensing range spot reflective type
Long sensing range line reflective type
Industry standard mounting pitch
Easy and accurate adjustments
The mounting pitch for sensor heads is
25.4 mm 1.000 in, the same industry standard as the
CX-400 series Ver.2 general purpose photoelectric
sensors. Hence, existing mounting brackets can be used
even when replacing general purpose sensors with laser
sensors.
A spot-size adjuster is built into the back of the sensor
head allowing the user to adjust the sensor easily while
viewing the spot. The adjuster is adjustable with a
screwdriver to avoid accidents during maintenance or
any other time the sensors are handled.
The spot shape can be adjusted
according to the object.
Long sensing range line reflective type: LS-H22
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
Long sensing range spot reflective type: LS-H21(-A)
Easy adjustment while
viewing the spot.
Coaxial retroreflective type: LS-H91(-A), LS-H92
FA COMPONENTS
Laser emission indicator
MACHINE VISION
SYSTEMS
Operation indicator
General purpose photoelectric
sensor CX-400 series Ver.2
Spot-shape adjuster
Highly reliable built-in multiple
turn-type knob allows you to
adjust the spot shape easily.
Slim size
Identical shape and mounting
214
11.2 mm 0.441 in
Spot-shape adjuster
(multiple turn)
Industry standard
mounting pitch
25.4mm 1.000 in
Line-up of FDA / IEC / JIS
Class 1 type
LS-H91(F)-A, LS-H21(F)-A
Sensor mounting bracket for beam axis
MS-CX-11
alignment is available
Visible light spot using the Class 1 type.
This makes beam axis alignment much easier.
It is possible to make a minor adjustment for the bracket
by 4 degrees up, down, right or left, even after setting
up the sensor. The bracket can be mounted in both
longitudinal and lateral directions.
4 degrees up and down
4 degrees
right and left
Vertical
adjustment
screw
Hole for the
foot angled
mounting
bracket
Sensor mounting bracket
for beam axis alignment
MS-CX-11
Horizontal
Hole for the foot
adjustment screw biangled mounting bracket
UV CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
LS-400
215
FIBER
SENSORS
LASER
SENSORS
LS-400 SERIES
Digital Laser Sensor
Easy setting, dual display
Equipped with 2 large 4-digit digital displays. While checking the current incident light intensity (red display), the
optimal threshold value (green display) can be set easily.
PHOTOELECTRIC
SENSORS
10 mm 0.394 in
thickness
MICRO
PHOTOELECTRIC
SENSORS
Threshold value setting display
Green LED, 4 digits (Max. display: 9999)
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Current incident light intensity display Large jog switch
Red LED, 4 digits (Max. display: 9999)
Large MODE key
2 switches enable simple operation
Only two switches, the large MODE key and the large jog switch, are required for operation.
2
1
3
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
Pressing the switch
selects or cancels the
operating mode
Pressing the switch then
confirms the selected
setting
Moving the switch from
side to side allows items
to be selected
Wiring and space saving
The quick-connection cables enable reductions in wiring.
(connector type)
The connections and man-hours for the relay terminal
setup can be reduced and valuable space is saved.
Also, LS-400 series amplifiers can of course be
connected side-by-side with a connector type amplifier
of FX-500/300 series digital fiber sensors or DPS-400
series digital pressure sensors.
Digital fiber sensor
FX-500/300 series
Digital pressure sensor
DPS-400 series
Note: Because the transmission method varies depending on the
amplifiers, check the instruction manual for the amplifiers when
connecting them.
Up to 16 units can be
connected together
FA COMPONENTS
MACHINE VISION
SYSTEMS
New release of type with upper communication functions toamplifiers,
facilitate
preventive
LS-403
check
the instructionmaintenance!
manual for the amplifiers
when
UV CURING
SYSTEMS
Network communication possible
connecting them.
Can connect to Open Network CC-Link IE Field /
CC-Link / DeviceNet / EtherCAT via Communication
Unit for Open Network SC-GU3 series. Monitoring and
various settings can be done from PLC, PC, etc.
LS-500
LS-400
Current values
of connected
sensors are
shown.
1ch
しきい値 現在値
90
65
9ch
Threshold tracking function saves
maintenance time
This function seeks
changes in the light emitting
amount resulting from
changes in the environment
over long periods (such
as dust levels), so that
the incident light intensity
can be checked at desired
intervals and the threshold
values can be reset
automatically. This helps to
reduce the man-hours for
maintenance.
Incident light intensity
Selection
Guide
Amplifier
Built-in
Amplifierseparated
Note: Because the transmission method varies depending on the
Current value
The amount of light
received when there
is no object
Threshold value
Time
しきい値 現在値
0
0
2ch
50
0
10ch
0
0
3ch
40
70
11ch
0
0
4ch
0
0
12ch
0
0
5ch
0
0
13ch
0
0
6ch
0
0
14ch
0
0
7ch
0
0
15ch
0
0
8ch
0
0
16ch
0
0
End unit
[Touch panel display example]
Threshold values of
connected sensors are
shown.
Communication Unit
for Open Network
SC-GU3 series
Digital laser sensor
Digital fiber sensor
Digital fiber sensor
Digital pressure sensor
LS-403/501
FX-501/502
FX-301/305
DPS-401/402
*CC-Link and CC-Link IE Field are a registered trademark of
Mitsubishi Electric Corporation.
DeviceNet is a registered trademark of ODVA (Open DeviceNet
Vender Association, Inc.).
EtherCAT is a registered trademark of Beckhoff Automation GmbH.
*Refer to p.971~ for details of SC-GU3 series.
Digital Laser Sensor
LS-400 SERIES
4 new modes enabling wide array of sensing
Hysteresis mode
Window comparator mode
FIBER
SENSORS
2 independent output modes Differential sensing mode
NG: Over range
By adjusting the hysteresis,
convexo-concave parts of uneven
objects can be cancelled enabling
more stable sensing.
The sensor judges any object
outside the range of incident light
intensity established by two set
threshold values.
Incident light intensity
NG: Under range
OK
To left
MICRO
PHOTOELECTRIC
SENSORS
OUT1
OFF
ON
OK
To right
LASER
SENSORS
PHOTOELECTRIC
SENSORS
ON
AREA
SENSORS
OUT2
OFF
By combining two outputs, wide
array of control is possible, allowing
you to detect meandering objects,
for example.
Only rapid changes in light received
are detected, which enable the edge of
glass, etc. to be detected accurately.
Optimal for positioning.
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
MODE NAVI customized function
SENSOR
OPTIONS
Frequently used functions such as response time,
M.G.S. function, data bank load, emission halt function
and D-CODE values can be stored in CUSTOM mode.
The settings are changed easily.
SIMPLE
WIRE-SAVING
UNITS
Response time
M.G.S. function
CUSTOM mode
WIRE-SAVING
SYSTEMS
Data bank load
MEASUREMENT
SENSORS
Emission halt function
STATIC
CONTROL
DEVICES
D-CODE
LASER
MARKERS
Accurately sense the minutest variations
(M.G.S. function)
Cable type allows external input
When sensing at close range or when the target objects
are transparent or minute, adjust the sensor receiving
sensitivity to one of 3 levels (U-LG mode: 4 levels) for
the optimal setting. In addition, changing the receiving
sensitivity will not effect the response time.
The LS-401-C2 cable-type amplifier is equipped with an
external input wire (5-core). It is ideal to use the laser
sensor at places where external teaching or laser light
emission halting is to be carried out, or at the places
where the laser sensor is to be used separately.
PLC
External input
Receiving sensitivity: High
• Laser emission halt
• Teaching
Receiving sensitivity: Medium
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
2 m 6.562 ft cable
attached
Receiving sensitivity: Low
Selection
Guide
Amplifier
Built-in
Amplifierseparated
Interference prevention function
The sensitivity can be changed
without changing the response time.
216
The automatic interference
prevention function prevents
against interference among
up to 4 sensors.
LS-500
LS-400
Setting conditions viewed at a glance (D-CODE)
Emission halt function
If you do not want to
place a laser spot in
the visual range of
the image processor,
you can stop the laser
radiation using the
emission halt signal
from the external input.
The amplifier setting is shown as an 8-digit code. Handy
for remote indications and follow-ups.
Third digit:
Response time
First digit:
Output operation
Second digit:
Timer operation
Fourth digit:
M.G.S. function
Fifth digit:
Hysteresis
Seventh digit:
Customized function
Eighth digit:
Sensing mode
Sixth digit:
External input mode
217
Digital Laser Sensor
LS-400 SERIES
ORDER GUIDE
FIBER
SENSORS
LASER
SENSORS
Sensor heads
PHOTOELECTRIC
SENSORS
Type
MICRO
PHOTOELECTRIC
SENSORS
Appearance
AREA
SENSORS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Class 2
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
Coaxial
retroreflective
Class 1
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
LS-400
Long
sensing
range spot
reflective
Long
sensing
range line
reflective
Class 1
STATIC
CONTROL
DEVICES
Diffuse reflective
MEASUREMENT
SENSORS
Class 2
WIRE-SAVING
SYSTEMS
Class 2
SIMPLE
WIRE-SAVING
UNITS
Model No.
Conforming
standards
LS-H92 (Note 1)
IEC / JIS / GB
LS-H92F (Note 2)
FDA / IEC / JIS
LS-H91 (Note 1)
IEC / JIS / GB
LS-H91F (Note 2)
FDA / IEC / JIS
LS-H91-A (Note 1)
IEC / JIS / GB
0.2 to 30 m 0.656 to 98.425 ft (Note 4)
0.2 to 20 m 0.656 to 65.617 ft (Note 4)
0.2 to 10 m 0.656 to 32.808 ft (Note 4)
0.2 to 10 m 0.656 to 32.808 ft (Note 4)
0.1 to 7 m 0.328 to 22.966 ft (Note 4)
0.1 to 5 m 0.328 to 16.404 ft (Note 4)
0.1 to 3 m 0.328 to 9.843 ft (Note 4)
0.1 to 3 m 0.328 to 9.843 ft (Note 4)
0.1 to 5 m 0.328 to 16.404 ft (Note 4)
0.1 to 3 m 0.328 to 9.843 ft (Note 4)
0.1 to 1 m 0.328 to 3.281 ft (Note 4)
0.1 to 1 m 0.328 to 3.281 ft (Note 4)
LS-H91F-A (Note 2) FDA / IEC / JIS
LS-H21 (Note 1)
IEC / JIS / GB
LS-H21F (Note 2)
FDA / IEC / JIS
LS-H21-A (Note 1)
IEC / JIS / GB
LS-H21F-A (Note 2) FDA / IEC / JIS
LS-H22 (Note 1, 3)
: U-LG
: STD
: FAST
: H-SP
Sensing range
30 to 1,000 mm 1.181 to 39.370 in
30 to 500 mm 1.181 to 19.685 in
30 to 300 mm 1.181 to 11.811 in
30 to 300 mm 1.181 to 11.811 in
30 to 500 mm 1.181 to 19.685 in
30 to 250 mm 1.181 to 9.843 in
30 to 150 mm 1.181 to 5.906 in
30 to 150 mm 1.181 to 5.906 in
IEC / JIS / GB
LS-H22F (Note 2, 3) FDA / IEC / JIS
30 to 1,000 mm 1.181 to 39.370 in
30 to 500 mm 1.181 to 19.685 in
30 to 300 mm 1.181 to 11.811 in
30 to 300 mm 1.181 to 11.811 in
NOTE: Mounting bracket is not supplied with the sensor head. Please select from the range of optional sensor head mounting
brackets.
Notes: 1) Obtained Korea’s S-mark certification.
2) This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and
Radiological Health) under the FDA (Food and Drug Administration). For details, refer to the Laser Notice No. 50.
3) LS-H22(F) is the model No. for LS-H21(F) long sensing range spot reflective type sensor head combined with the LS-MR1 lens attachment for line
reflective type sensor head. Hence, LS-H21(F) appears on the sensor head itself.
4) The sensing range is the value for the RF-330 [RF-230 for the LS-H92(F)] reflector. In addition, the sensing range is the possible setting range for the
reflector. The sensor can detect an object less than 0.1 m 0.328 ft [LS-H92(F): 0.2 m 0.656 ft] away. Note that if there are white papers or specular
objects near the sensor head, reflected light from these objects may be received. In such cases, use the M.G.S. function of the amplifier unit to change
the response time or incident light sensitivity.
5 m 16.404 ft cable length type
5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) is also available.
When ordering this type, suffix “-C5” to the model No.
• LS-H91-C5
• LS-H91-A-C5
• LS-H21-C5
• LS-H22-C5
Package without reflector
The LS-H91(F), LS-H91(F)-A and LS-H92(F) are also available without the reflector (RF-330 or RF-230).
When ordering this type, suffix “-Y” to the model No.
• LS-H92-Y
• LS-H92F-Y
• LS-H91-A-Y
• LS-H91F-A-Y
• LS-H91-Y
• LS-H91F-Y
Digital Laser Sensor
LS-400 SERIES
218
ORDER GUIDE
FIBER
SENSORS
Amplifiers
LASER
SENSORS
Type
Appearance
Model No.
Cable type
(With external input)
Connection method
LS-401 (Note 1)
NPN open-collector
transistor two outputs
LS-401P
PNP open-collector
transistor two outputs
LS-403
NPN open-collector
transistor two outputs
LS-401-C2 (Note 1)
NPN open-collector
transistor two outputs
LS-401P-C2
PNP open-collector
transistor two outputs
Connector type
With upper
communication
function (Note 2)
Output
MICRO
PHOTOELECTRIC
SENSORS
Use quick-connection cable (4-core) (optional)
2 m 6.562 ft cabtyre cable (5-core) included
Cable outer diameter: ø3.7 mm ø0.146 in
Quick-connection cables Quick-connection cable is not supplied with the connector type amplifier. Please order it separately.
Appearance
Model No.
CN-74-C1
Main cable
(4-core)
Sub cable
(2-core)
Description
Length: 1 m 3.281 ft
0.2 mm2 4-core cabtyre cable,
with connector on one end
Cable outer diameter: ø3.3 mm ø0.130 in
Note: LS-H92(F) only
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
STATIC
CONTROL
DEVICES
CN-74-C5
Length: 5 m 16.404 ft
PLC
CN-72-C1
Length: 1 m 3.281 ft
HUMAN
MACHINE
INTERFACES
CN-72-C2
Length: 2 m 6.562 ft
0.2 mm2 2-core cabtyre cable,
with connector on one end
Cable outer diameter: ø3.3 mm ø0.130 in
Length: 5 m 16.404 ft
Model No.
LASER
MARKERS
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Description
When cascading multiple amplifiers, or when it moves depending on the way it is installed on
a DIN rail, these end plates clamp amplifiers into place on both sides. Make sure to use end
plates when cascading multiple amplifiers together.
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
Accessories
• RF-230 (Reflector)
PARTICULAR
USE
SENSORS
Length: 2 m 6.562 ft
Two pcs. per set
• RF-330 (Reflector)
INDUCTIVE
PROXIMITY
SENSORS
MEASUREMENT
SENSORS
End plates End plates are not supplied with the amplifier. Please order them separately when the amplifiers are mounted in cascade.
MS-DIN-E
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
CN-74-C2
CN-72-C5
Type
AREA
SENSORS
PRESSURE /
FLOW
SENSORS
Notes: 1) Obtained Korea’s S-mark certification.
2) F
or upper communication, a communication unit for open network SC-GU3 series is needed separately. Refer to p.971~ for SC-GU3 series.
Type
PHOTOELECTRIC
SENSORS
• CN-EP1 (Connector for amplifier)
5 pcs. per set (Note)
Note: One is attached to each
sensor head according to
standard.
• LS-MR1 (Lens attachment for line reflective type)
LS-400
219
FIBER
SENSORS
Digital Laser Sensor
LS-400 SERIES
OPTIONS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Designation
Model No.
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
Foot angled mounting bracket
MS-CX-2
Foot biangled mounting bracket
Flat mounting possible to avoid obstructions caused by the height of the sensor.
MS-CX-3
Back angled mounting bracket
MS-CX-4
Protective mounting bracket
Protects sensors preventing beam axis displacement due to shocks.
MS-CX-11
Mounting bracket that makes fine beam axis alignment possible
after setting the sensor head.
Adjustment angle: up and down, right and left: 4 degrees
Mounting directions: two directions, vertical and horizontal
MS-AJ1
Horizontal mounting type
MS-AJ2
Vertical mounting type
MS-AJ1-A
Horizontal mounting type
MS-AJ2-A
Vertical mounting type
Amplifier mounting bracket
MS-DIN-2
Mounting bracket for amplifier
Reflector mounting bracket
MS-RF23
Mounting bracket for RF-230
Amplifier
protection seal
FX-MB1
10 sets of 2 communication window seals and 1 connector seal
Communication window seal: It prevents malfunction due to transmission signal from another
amplifier, as well as, prevents effect on another amplifier.
Connector seal: It prevents contact of any metal, etc., with the pins
of the quick-connection cable.
Reflector
RF-310
For coaxial retroreflective type
Compact reflector
RF-33
For coaxial retroreflective type
Size: 25.2 × 27.8 × t 0.4 mm
0.992 × 1.094 × t 0.016 in
RF-31
For coaxial retroreflective type
Size: 9.2 × 9.2 × t 0.4 mm
0.362 × 0.362 × t 0.016 in
Sensor head
mounting
bracket
Sensor mounting
bracket for beam
axis alignment
Universal sensor
mounting stand
(Note 1)
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
Reflective tape
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
• MS-CX-1
MS-CX-1
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
Sensor head mounting bracket
Description
Bank
selection unit
(Note 2)
FX-CH
NPN input type
FX-CH-P
PNP input type
Amplifier
Built-in
Amplifierseparated
LS-500
LS-400
Two M3 (length 12 mm
0.472 in) screws with
washers are attached.
Two M3 (length 12 mm
0.472 in) screws with
washers are attached.
• MS-CX-3
• MS-CX-4
Basic assembly
Lateral arm assembly
Two M3 (length 12 mm
0.472 in) screws with
washers are attached.
Two M3 (length 12 mm
0.472 in) screws with
washers are attached.
Sensor mounting bracket
for beam axis alignment
• MS-CX-11
Two M3 (length 14 mm
0.551 in) screws with
washers are attached.
Sensing range (U-LG mode)
• LS-H91(F): 0.1 to 7 m
0.328 to 22.966 ft
• LS-H91(F)-A: 0.1 to 5 m
0.328 to 16.404 ft
Amplifier mounting bracket
• MS-DIN-2
Setting for up to 16 laser sensors can be
changed at once by means of external signals.
Notes: 1) Refer to p.953~ for the universal sensor mounting stand MS-AJ series.
2) Refer to p.166 for the bank selection unit FX-CH.
Reflector mounting bracket
Universal sensor mounting stand
Selection
Guide
• MS-CX-2
• MS-AJ1
• MS-AJ1-A
• MS-AJ2
With the lateral arm,
Swivel:
360° rotation the sensor can
45°
45°
Elevation
angle: ±45°
Height
adjustment:
150 mm
5.906 in
approx.
Mounting hole
for M6 screw
sense from above
a production line.
Swivel:
360°
rotation
45°
Height
Elevation
adjustment: angle:
150 mm
±45°
5.906 in
approx.
Forward / back
adjustment
130 mm
5.118 in
approx.
360°
45°
Angle 45°
adjustment:
±45°
45°
Mounting hole
for M6 screw
Reflector
Reflective tape
• RF-310
• RF-33
4 mm
0.157 in
12 mm
0.472 in
0.4 mm
0.016 in
24 mm
0.945 in
• RF-31
0.4 mm
0.016 in
45°
27.8 mm
1.094 in
25.2 mm
0.992 in
9.2 mm
0.362 in
9.2 mm
0.362 in
• MS-RF23
• MS-AJ2-A
With the lateral arm,
Swivel:
360° rotation the sensor can
Swivel:
sense from above a 360° rotation
Height
production line.
adjustment:
Forward / back
150 mm
adjustment
Height
5.906 in
130 mm
adjustment:
approx.
5.118 in
150 mm
approx.
5.906 in
Mounting hole
approx.
for M6 screw
360°
Amplifier
Angle
adjustment:
±45°
45°
Mounting hole
for M6 screw
Two M4 (length 10 mm 0.394 in)
screws with washers are attached.
protection seal
• FX-MB1
Communication
window seal
Connector seal
Bank selection unit
• FX-CH(-P)
Digital Laser Sensor
LS-400 SERIES
SPECIFICATIONS
FIBER
SENSORS
LASER
SENSORS
Sensor heads
Coaxial retroreflective
Model No.
Type
Item
Class 2
Class 1
Long sensing range
line reflective
MICRO
PHOTOELECTRIC
SENSORS
LS-H91
LS-H91-A
LS-H21
LS-H21-A
LS-H22(Note 3)
AREA
SENSORS
FDA (Note 2) / IEC / JIS
standards conforming type
LS-H92F
LS-H91F
LS-H91F-A
LS-H21F
LS-H21F-A
LS-H22F(Note 3)
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
EMC Directive, RoHS Directive
LS-401(P), LS-401(P)-C2, LS-403
U-LG mode
0.1 to 7 m
0.1 to 5 m
0.2 to 30 m
0.656 to 98.425 ft (Note 4) 0.328 to 22.966 ft (Note 4) 0.328 to 16.404 ft (Note 4)
30 to 1,000 mm
1.181 to 39.370 in
30 to 500 mm
1.181 to 19.685 in
30 to 1,000 mm
1.181 to 39.370 in
STD mode
0.1 to 5 m
0.1 to 3 m
0.2 to 20 m
0.656 to 65.617 ft (Note 4) 0.328 to 16.404 ft (Note 4) 0.328 to 9.843 ft (Note 4)
30 to 500 mm
1.181 to 19.685 in
30 to 250 mm
1.181 to 9.843 in
30 to 500 mm
1.181 to 19.685 in
0.2 to 10 m
0.1 to 3 m
0.1 to 1 m
0.656 to 32.808 ft (Note 4) 0.328 to 9.843 ft (Note 4) 0.328 to 3.281 ft (Note 4)
30 to 300 mm
1.181 to 11.811 in
30 to 150 mm
1.181 to 5.906 in
30 to 300 mm
1.181 to 11.811 in
FAST mode
Operation indicator
Orange LED (lights up when the amplifier output is ON)
Laser emission indicator
–
Ambient temperature
IP40 (IEC)
SIMPLE
WIRE-SAVING
UNITS
STATIC
CONTROL
DEVICES
35 to 85 % RH, Storage: 35 to 85 % RH
LASER
MARKERS
Ambient illuminance
Incandescent light: 3,000 ℓx or less at the light-receiving face
Voltage withstandability
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 500 Hz frequency, 1.5 mm 0.059 in (10 G max.) double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Shock resistance
FDA (Note 2) / IEC /
JIS standards
conforming type
SENSOR
OPTIONS
–10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –20 to +70 °C –4 to +158 °F
Ambient humidity
IEC / JIS / GB standards
conforming type
PARTICULAR
USE
SENSORS
MEASUREMENT
SENSORS
Multi-turn adjuster
Protection
INDUCTIVE
PROXIMITY
SENSORS
WIRE-SAVING
SYSTEMS
Green LED (lights up during laser emission)
Spot-shape adjuster
Environmental resistance
Class 2
LS-H92
H-SP mode
Emitting element
Long sensing range spot reflective
PHOTOELECTRIC
SENSORS
IEC / JIS / GB standards
conforming type
Applicable amplifiers
Sensing range
Diffuse reflective
Class 1
CE marking directive compliance
Red semiconductor laser,
Class 2 (IEC / JIS / GB)
Max. output: 3 mW
Peak emission wavelength: 655 nm 0.026 mil
Red semiconductor laser,
Class 2 (FDA / IEC / JIS)
Max. output: 3 mW
Peak emission wavelength: 655 nm 0.026 mil
Material
Cable
220
Red semiconductor laser, Red semiconductor laser, Red semiconductor laser, Red semiconductor laser,
Class 1 (IEC / JIS / GB) Class 2 (IEC / JIS / GB) Class 1 (IEC / JIS / GB) Class 2 (IEC / JIS / GB)
Max. output: 1 mW
Max. output: 3 mW
Max. output: 1 mW
Max. output: 3 mW
Peak emission wavelength:
Peak emission wavelength:
Peak emission wavelength:
Peak emission wavelength:
655 nm 0.026 mil
655 nm 0.026 mil
655 nm 0.026 mil
655 nm 0.026 mil
Red semiconductor laser, Red semiconductor laser, Red semiconductor laser, Red semiconductor laser,
Class 1 (FDA / IEC / JIS) Class 2 (FDA / IEC / JIS) Class 1 (FDA / IEC / JIS) Class 2 (FDA / IEC / JIS)
Max. output: 1 mW
Max. output: 3 mW
Max. output: 1 mW
Max. output: 3 mW
Peak emission wavelength:
Peak emission wavelength:
Peak emission wavelength:
Peak emission wavelength:
655 nm 0.026 mil
655 nm 0.026 mil
655 nm 0.026 mil
655 nm 0.026 mil
Enclosure: PBT (Mounting part: PEI), Lens cover: Acrylic
0.1 mm , single core two parallel shielded cables, 2 m 6.562 ft long (Connector for amplifier attached) (Note 5)
2
Weight
Net weight: 30 g approx.
Gross weight: 40 g approx.
Net weight: 30 g approx.
Gross weight: 45 g approx.
Net weight: 30 g approx.
Gross weight: 40 g approx.
Net weight: 35 g approx.
Gross weight: 45 g approx.
Accessories
LS-MR1
RF-230(Reflector): RF-330(Reflector): RF-330(Reflector):
Lens attachment
1 pc. Warning label: 1 set Explanation label: 1 set
1 pc.
1 pc.
for line reflective : 1 pc.
Warning label: 1 set Warning label: 1 set Explanation label: 1 set Labels are written in
Labels are written in
Warning
label: 1 set
Labels are written in
Japanese, English and
Japanese and Chinese
Labels are written in
Labels are written in
Labels are written in
Japanese, English and
Chinese for compliance
for compliance with
Japanese, English and
Japanese and Chinese
Japanese, English and
Chinese for compliance
with various standards.
various standards.
Chinese for compliance
for compliance with
Chinese for compliance
with various standards.
with various standards.
various standards.
with various standards.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and
Radiological Health) under the FDA (Food and Drug Administration). For details, refer to the Laser Notice No. 50.
3) LS-H22(F) is the set model No. for LS-H21(F) long sensing range spot reflective type sensor head combined with the LS-MR1 lens attachment for line
reflective type. Hence, LS-H21(F) appears on the sensor head itself.
4) The sensing range is the value for the RF-330 [RF-230 for the LS-H92(F)] reflector. In addition, the sensing range is the possible setting range for the
reflector. The sensor can detect an object less than 0.1 m 0.328 ft [LS-H92(F): 0.2 m 0.656 ft] away. Note that if there are white papers or specular
objects near the sensor head, reflected light from these objects may be received. In such cases, use the M.G.S. function of the amplifier unit to change
the response time or incident light sensitivity.
5) Cable cannot be extended.
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
LS-400
221
Digital Laser Sensor
SPECIFICATIONS
FIBER
SENSORS
LASER
SENSORS
Amplifiers
PHOTOELECTRIC
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
Model No.
Item
NPN output
LS-401
LS-403
LS-401-C2
PNP output
LS-401P
–
LS-401P-C2
EMC Directive, RoHS Directive
Supply voltage
12 to 24 V DC ±10 % Ripple P-P 10 % or less
Power consumption
Outputs
(Output 1, Output 2)
Normal operation: 950 mW or less (Current consumption 40 mA or less at 24 V supply voltage)
ECO mode: 780 mW or less (Current consumption 33 mA or less at 24 V supply voltage)
NPN open-collector transistor
• Maximum sink current: 100 mA (LS-401□) (Note 2) , 50 mA (LS-403) (Note 3)
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1.5 V or less at 100 mA (Note 2) sink current
at 50 mA (Note 3) sink current (LS-403)
Output operation
SIMPLE
WIRE-SAVING
UNITS
Response time
LASER
MARKERS
Incorporated
80 µs or less (H-SP), 150 µs or less (FAST), 500 µs or less (STD), 4 ms or less (U-LG) selectable with jog switch
NPN non-contact input
• Signal condition
High: +5 V to +V or open,
Low: 0 to +2 V (source current 0.5 mA or less)
• Input impedance: 10 kΩ approx.
External input
Laser emission halt
Full-auto teaching /
Limit teaching
–
PNP non-contact input
• Signal condition
High: +4 V to +V (sink current 3 mA or less)
Low: 0 to +0.6 V or open
• Input impedance: 10 kΩ approx.
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Operation indicator
Orange LED (lights up when output 1 and output 2 are ON)
Laser emission indicator
Green LED (lights up during laser emission)
Select indicator
Yellow LED (lights up when either output 1 or output 2 is selected)
MODE indicator
RUN: Green LED, TEACH • L/D • TIMER • CUST • PRO: Yellow LED
Digital display
4 digit (green) + 4 digit (red) LED display
Sensitivity setting
Normal mode: 2-level teaching / Limit teaching / Full-auto teaching / Manual adjustment
Window comparator mode: Teaching (1-level, 2-level, 3-level) / Manual adjustment
Hysteresis mode: Teaching (1-level, 2-level, 3-level) / Manual adjustment
Differential mode: 5-level settings (LS-403: 8-level settings)
Fine sensitivity adjustment function
Amplifierseparated
LS-500
LS-400
Timer function
Incorporated
Incorporated with variable ON-delay / OFF-delay / One shot timer, switchable either effective or ineffective.
Timer period
Automatic interference
prevention function
Environmental resistance
Selection
Guide
Amplifier
Built-in
PNP open-collector transistor
• Maximum source current: 100 mA (Note 2)
• Applied voltage: 30 V DC or less (between output and +V)
• Residual voltage: 1.5 V or less [at 100 mA (Note 2) source current]
Selectable either Light-ON or Dark-ON, with jog switch
Short-circuit protection
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
Cable type
With upper communication function
CE marking directive compliance
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
Connector type
Type
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
LS-400 SERIES
Ambient temperature
1 to 9,999 ms approx.
0.5 ms approx. 1 to 9,999 ms approx.
Incorporated [Up to four sets of sensor heads can be mounted close together. (However, LS-401□ is disabled when in H-SP
mode, up to two sets of LS-403 can be mounted close together when in H-SP mode)]
–10 to +55 °C +14 to +131 °F (If 4 to 7 units are mounted close together: –10 to +50 °C +14 to +122 °F,
if 8 to 16 units are mounted close together: –10 to +45 °C +14 to +113 °F) (No dew condensation or icing allowed), Storage: –20 to +70 °C 4 to +158 °F
Ambient humidity
Voltage withstandability
1 to 9,999 ms approx.
35 to 85 % RH, Storage: 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
Shock resistance
Material
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Enclosure: Heat-resistant ABS, Transparent cover: Polycarbonate, Push button switch: Acrylic, Jog switch: ABS
Cable
– (Note 4)
Cable extension
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Weight
Net weight: 15 g approx., Gross weight: 20 g approx.
0.15 mm2 5-core cabtyre cable, 2 m 6.562 ft long
Net weight: 65 g approx., Gross weight: 75 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) In case of LS-401(P), 50 mA if 5 to 8 amplifiers are connected in cascade, and 25 mA if 9 to 16 amplifiers are connected in cascade.
3) In case of LS-403, 25 mA if 5 to 16 amplifiers are connected in cascade.
4) The cable is not supplied as an accessory for connector type. Be sure to purchase the optional quick-connection cables given below.
When connecting to SC-GU3 series, be sure to purchase the optional cascading connector unit.
Main cable (4-core): CN-74-C1 (cable length 1 m 3.281 ft), CN-74-C2 (cable length 2 m 6.562 ft), CN-74-C5 (cable length 5 m 16.404 ft)
Sub cable (2-core): CN-72-C1 (cable length 1 m 3.281 ft), CN-72-C2 (cable length 2 m 6.562 ft), CN-72-C5 (cable length 5 m 16.404 ft)
Cascading connector unit: SC-71
Digital Laser Sensor
LS-400 SERIES
I/O CIRCUIT AND WIRING DIAGRAMS
FIBER
SENSORS
LS-401(-C2) LS-403
NPN output type
I/O circuit diagram
D
1
Sensor circuit
Tr1
2
Tr2
4
ZD2
+5V
(Brown) +V (Note 1)
Brown (Note 1)
Load
Load
(White) Output 2 100 mA / 50 mA max. (Note 3,4) +
–
100 mA / 50 mA max. (Note 3,4)
ZD1
Black
(Blue) 0 V (Note 1)
Internal circuit
Load
Load
+
–
Pink (Note 2)
12 to 24V DC
±10 %
Blue (Note 1) * 1
*1
Users’ circuit
Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue).
The power is supplied from the connector of the main cable.
2) Connector type LS-401/403 does not incorporate the external
input.
3) LS-401(-C2) is 100 mA max, however, LS-401(-C2) is 50 mA max.
if 5 to 8 amplifiers are connected in cascade, and 25 mA max. if 9
to 16 amplifiers are connected in cascade.
4) LS-403 is 50 mA max, however, it is 25 mA max. if 5 to 16
amplifiers are connected in cascade.
Notes: 1) The quick-connection sub cable does not have brown lead wire
and blue lead wire.
The power is supplied from the connector of the main cable.
2) The quick-connection cable does not have a pink lead wire.
Terminal layout of connector type
2
Output 1
• External input
High: +5 V to +V, or open
Low: 0 to +2 V (source current: 0.5 mA or less)
• Beam emission halts and teaching occurs
when at Low.
or
PARTICULAR
USE
SENSORS
MEASUREMENT
SENSORS
* Connector for amplifier (CN-EP1) pin position
Terminal No.
1
2
3
Symbols … D: Reverse supply polarity protection diode
ZD1, ZD2: Surge absorption zener diode
Tr1, Tr2: NPN output transistor
INDUCTIVE
PROXIMITY
SENSORS
WIRE-SAVING
SYSTEMS
4
Output 2
0V
Non-voltage contact or NPN open-collector transistor
PRESSURE /
FLOW
SENSORS
SIMPLE
WIRE-SAVING
UNITS
Terminal No.
3
* 1
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
SENSOR
OPTIONS
1
+V
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
White
12 to 24V DC
±10 %
(Pink) External input (Note 2)
3
Color code of cable type/quick-connection cable
Color code of cable type/quick-connection cable
(Black) Output 1
LASER
SENSORS
PHOTOELECTRIC
SENSORS
Wiring diagram
Terminal No. of connector type
222
4
Connection cable
1
Conductor core wire: Brown
2
Shield wire
3
Conductor core wire: Yellow
4
Shield wire
Cable color: Gray
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
Cable color: Black
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
LS-401P(-C2)
PNP output type
I/O circuit diagram
Wiring diagram
Terminal No. of connector type
Sensor circuit
1
ZD1
0V
Tr1
ZD2
Tr2
4
D
Internal circuit
Pink (Note 2)
*1
Black
(Pink) External input (Note 2)
*1
3
(Black) Output 1
100 mA max. (Note 3)
(White) Output 2
Load
–
12 to 24V DC
±10 %
Load
(Blue) 0 V (Note 1)
Users’ circuit
Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue).
The power is supplied from the connector of the main cable.
2) Connector type LS-401P does not incorporate the external input.
3) LS-401P is 50 mA max. if 5 to 8 amplifiers are connected in
cascade, and 25 mA max. if 9 to 16 amplifiers are connected in
cascade.
Blue (Note 1)
Non-voltage contact or PNP open-collector transistor
• External input
High: +4 V to +V (sink current: 3 mA or less)
Low: 0 to +0.6 V, or open
• Beam emission halts and teaching occurs
when at High.
12 to 24V DC
±10 %
Terminal No.
4
Output 2
3
0V
* Connector for amplifier (CN-EP1) pin position
Terminal No.
2
3
4
Connection cable
1
Conductor core wire: Brown
2
Shield wire
3
Conductor core wire: Yellow
4
Shield wire
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
LS-400
1
+V
1
Symbols … D: Reverse supply polarity protection diode
ZD1, ZD2: Surge absorption zener diode
Tr1, Tr2: PNP output transistor
–
Terminal layout of connector type
Output 1
* 1
Load
Load
Notes: 1) The quick-connection sub cable does not have brown lead wire
and blue lead wire.
The power is supplied from the connector of the main cable.
2) The quick-connection cable does not have a pink lead wire.
2
or
+
White
+
UV
CURING
SYSTEMS
Brown (Note 1)
(Brown) +V (Note 1)
100 mA max. (Note 3)
2
Color code of cable type/quick-connection cable
Color code of cable type/quick-connection cable
MACHINE
VISION
SYSTEMS
Cable color: Gray
Cable color: Black
223
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
Digital Laser Sensor
PRECAUTIONS FOR PROPER USE
• This catalog is a guide to select a suitable product.
Be sure to read the instruction manual attached to the
product prior to its use.
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
PARTICULAR
USE
SENSORS
Cautions for laser beams
• These products are class 2 (LS-H□-A:
Class 1) laser in compliance with IEC / JIS /
GB standards and FDA* regulations. Do not
look at the laser beam directly or through
optical system such as a lens.
• The following label is attached to the
product. Handle the product according to the
instruction given on the warning label.
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
IEC / JIS / GB Class 2 type
FDA Class 1 type
This product has warning labels attached
and included in the packaging that are
written in Japanese, English and Chinese
for compliance with various standards.
This product has explanation labels attached
and included in the packaging that are
written in Japanese, English and Chinese for
compliance with various standards.
* This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice
No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and
Radiological Health) under the FDA (Food and Drug Administration).
Safety standards for laser beam products
• A laser beam can harm human being’s eyes, skin, etc.,
because of its high energy density. IEC has classified
laser products according to the degree of hazard and the
stipulated safety requirements. LS-H□(F) is classified as
Class 2 laser. LS-H□(F)-A is classified as Class 1 laser.
Classification by IEC 60825-1
Selection
Guide
Amplifier
Built-in
Classification
LS-400
Description
Class 1
Lasers that are safe under reasonably foreseeable conditions
of operation, including the use of optical instruments for
intrabeam viewing.
Class 2
Lasers that emit visible radiation in the wavelength range from
400 nm to 700 nm where eye protection is normally afforded
by aversion responses, including the blink reflex.
This reaction may be expected to provide adequate protection
under reasonably foreseeable conditions of operation
including the use of optical instruments for intrabeam viewing.
Amplifierseparated
LS-500
Refer to p.1552~ for general precautions and p.1593~ for information about laser beam.
Part description (Amplifier)
Select 1 indicator (Yellow)
Select 2 indicator (Yellow)
MODE indicator / TIMER (Yellow)
Output 1 operation indicator (Orange)
Output 2 operation indicator (Orange)
MODE indicator / CUSTOM (Yellow)
Laser emission indicator
(Green)
AREA
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
LS-400 SERIES
Safe use of laser products
• For the purpose of preventing users from suffering
injuries by laser products, IEC 60825-1 (Safety of laser
products). Please check the standards before use.
(Refer to p.1593~ for information about laser beam.)
1
2
TIMER
CUST
LASER
L/D
ON
OUT
MODE indicator / RUN (Green)
MODE indicator / TEACH (Yellow)
PRO
MODE indicator /
L/D ON (Yellow)
MODE indicator /
PRO (Yellow)
3
PUSH
1
MODE
CANCEL
2
MODE key
Jog switch
Digital display (Green, Red)
Spot-shape adjuster (Only for LS-H21□, LS-H22□)
• The diffuse reflective type LS-H21□ and LS-H22□
incorporate the spot-shape adjuster to adjust the shape
of spots.
Spot-shape adjuster
Description
Turn the spot-shape adjuster clockwise or counterclockwise to adjust the spot shape at your desired
detecting distance. However, if the adjuster is
turned too far, it may be damaged.
Digital Laser Sensor
PRECAUTIONS FOR PROPER USE
224
Refer to p.1552~ for general precautions and p.1593~ for information about laser beam.
Mounting
Lens attachment for line reflective type (LS-MR1)
Amplifier
1 Fit the rear part of the mounting
section of the amplifier on a 35 mm
1.378 in width DIN rail.
2 Press down the rear part of the
mounting section of the unit on the
35 mm 1.378 in width DIN rail and
fit the front part of the mounting
section to the DIN rail.
1 Push the amplifier forward.
2 Lift up the front part of the amplifier
to remove it.
Note: Be careful. If the front part is lifted without
pushing the amplifier forward, the hook on
the rear portion of the mounting section is
likely to break.
1 Insert the sensor head connector
into the inlet until it clicks.
2 Fit the cover to the connector.
2
1
35mm 1.378 in width
DIN rail
1
2
• The lens attachment for line reflective type LS-MR1 mounted in
the long sensing range line reflective type LS-H22□ is removable.
When LS-H22□ is used without LS-MR1, it will provide the
equivalent performance to the long sensing range spot reflective
type LS-H21□. In addition, the optional LS-MR1 can be attached
to LS-H21□ to obtain the performance equivalent to LS-H22□.
• Keep the lens clean of dust, dirt, water, oil, grease, etc.
• Do not apply any excessive force to LS-MR1.
Such force may cause damage.
Removing method
Insert a screwdriver into the fixing slot located at the top of
sensor head.
2 Tilt the screwdriver inserted in Step 1 to remove LS-MR1.
1
2
1
Sensor head
connector
Cover
Mounting method
1
Sensor head
• The tightening torque should be 0.5 N·m or less.
M3 (length 12 mm
0.472 in) screw
with washers
Sensor head mounting
bracket (optional)
• When placing the sensor head horizontally or vertically, the
reflector must also be positioned horizontally or vertically as
shown in Fig. 1 below.
If the sensor head is placed horizontally or vertically but the
reflector is leaned as shown in Fig. 2 below, the reflection
amount will decrease, which may cause unstable detection.
Fig. 1 Proper positioning
When placing the sensor head horizontally or vertically, the
reflector shall also be positioned horizontally or vertically.
Fig. 2 Improper positioning
When placing
the sensor head
horizontally or
vertically, but the
reflector is leaned.
LS-400 SERIES
2
Fixing slot
The size of upper fixing
hook of LS-MR1 is not
same as the lower fixing
hook. After identifying
Lens attachment for
Fixing slot
line reflective type
the upper and lower
Fixing hooks
LS-MR1
fixing hooks, insert
LS-MR1 upper fixing hook into the fixing slot at the top of
sensor head and then insert LS-MR1 lower fixing hook into
the fixing slot at the bottom of sensor head.
After mounting, check that LS-MR1 is properly fixed to
the sensor head.
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
Wiring
• Make sure that the power supply is off while wiring.
• Verify that the supply voltage variation is within the rating.
• Take care that if a voltage exceeding the rated range is
applied, or if an AC power supply is directly connected, the
sensor may get burnt or damaged.
• Take care that short-circuit or wrong wiring of the load may
burn or damage the sensor.
• Do not run the wires together with high-voltage lines or
power lines or put them in the same raceway. This can
cause malfunction due to induction.
• Ensure that an isolation transformer is utilized for the DC
power supply. If an auto transformer is utilized, the main
amplifier or power supply may be damaged.
• Make sure to use the optional quick-connection cable for
the connection of the amplifier [connector type LS-401(P) /
LS-403]. Extension up to total 100 m 328.084 ft is possible
with 0.3 mm2, or more,cable. However, in order to reduce
noise, make the wiring as short as possible.
HUMAN
MACHINE
INTERFACES
Others
LS-400
• Do not use during the initial transient time (0.5 sec. approx.)
after the power supply is switched on.
• Because the sensitivity is higher in U-LG mode than in other
modes, it can be more easily affected by extraneous noise.
Check the operating environment before use.
• These sensors are only for indoor use.
• Avoid dust, dirt, and steam.
• Take care that the product does not come in direct contact
with water, oil, grease, or organic solvents, such as, thinner,
etc.
• This sensor cannot be used in an environment containing
inflammable or explosive gasses.
• Never disassemble or modify the sensor.
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
225
FIBER
SENSORS
LASER
SENSORS
Digital Laser Sensor
LS-400 SERIES
DIMENSIONS (Unit: mm in)
LS-H91(-A) LS-H91F(-A)
Sensor head
PHOTOELECTRIC
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
11.2
0.441
3
0.118
15.5
0.610
5
0.197
INDUCTIVE
PROXIMITY
SENSORS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
Beam emitting /
receiving part
UV
CURING
SYSTEMS
7.6
0.299
(18 0.709)
15.5
0.610
5 0.197
3
0.118
11.2
0.441 Beam3
receiving
0.118
part
(18 0.709)
LS-H22 LS-H22F
Sensor head
Spot-size adjuster
18.5
0.728
Beam- 31 25.4
emitting1.220 1.000
part
(
Select 1 indicator (Yellow)
Output 2 operation indicator (Orange)
Selection
Guide
Amplifier
Built-in
Amplifierseparated
11
0.433
LS-401-C2 LS-401P-C2
Output 1 operation indicator (Orange)
3 0.118
27.8
1.094
7
0.276
36.5
1.437
11
0.433
3.95 0.156
Suitable for 35 mm
1.378 in width DIN rail
LS-400
CN-74-C1 CN-74-C2 CN-74-C5
Main cable (Optional)
• Length L
50
1.969
L
CN-74-C1
1,000 39.370
2,000 78.740
CN-74-C5
5,000 196.850
ø3.3 ø0.130 cable
(
14
0.551
2.54
0.100
)
2.9
(0.114
)
10
0.394
6
0.236
( )
75
2.953
Communication window
3
0.118
10
0.394
2.54
0.100
7
0.2 0.276
0.008
10
0.394
13.6
0.535
3 0.118
ø3.7 0.146 cable, 2 m 6.562 ft long
27.8
1.094
13.05
0.514
30
1.181
10.5
0.413
24
3
0.945
Suitable for 35 mm 0.118
1.378 in width DIN rail
36.5
1.437
ø8
ø0.315
2
0.079
3
0.118
CN-72-C1 CN-72-C2 CN-72-C5
1.4 3.95
0.055 0.156
50
1.969
L
Model No.
Length L
CN-72-C1
1,000 39.370
CN-72-C2
2,000 78.740
CN-72-C5
5,000 196.850
9.2
0.362
Sub cable (Optional)
• Length L
ø3.3 ø0.130 cable
14
(0.551
)
2.54
0.100
3
0.118
2.9
(0.114
)
10
0.394
6
0.236
( )
12
10.5
(0.472
) 0.413
12
10.5
(0.472
) 0.413
2.65
0.104
Jog switch
Digital display (Red, Green)
Output 2 operation indicator (Orange)
10.5
0.413
CN-74-C2
MODE key
Laser emission indicator (Green)
Jog switch
30
1.181
Length L
Amplifier
12
0.472
58.7
30.85 2.311
1.215
8.4
2.7 0.106
0.331
5.15 0.203
Select 1 indicator (Yellow)
75
2.953
Communication window
Model No.
(18 0.709)
16
(0.630
)
MODE key
24
3
0.945
0.118
LS-500
ø1.45 ø0.057, single core
two parallel shielded cables
Select 2 indicator (Yellow)
Digital display (Red, Green)
3
10 0.118
0.394
CN-EP1
2-M3 × 0.5 0.020
thru-hole threads
12
0.472
Output 1 operation indicator (Orange)
Spot-size adjuster
2,000
(78.740
)
Amplifier
58.7
30.85 2.311
8.4 1.215
2.7 0.106
0.331
5.15 0.203
4
( 0.157
)
18.5
0.728
18.5
)
)
Laser emission indicator (Green)
25
0.984
3 0.118
16
0.630
2,000
78.740
LS-401 LS-401P LS-403
Laser emission indicator (Green)
3
0.118
Beamemitting
part
(18 0.709)
(
3.5
0.138
1.5 0.059
Beam11.2
receiving
0.441
part
5
0.197
33.5 31 25.4 0.728
(1.319
) 1.220 1.000
CN-EP1
2-M3 × 0.5 0.020
thru-hole threads
ø1.45 ø0.057, single core
two parallel shielded cables
Select 2 indicator (Yellow)
Operation indicator (Orange)
Laser emission indicator (Green)
25
0.984
CN-EP1
16
(0.630
)
2-M3 × 0.5 0.020
thru-hole threads
ø1.45 ø0.057, single core
two parallel shielded cables
2,000
(78.740
)
Sensor head
HUMAN
MACHINE
INTERFACES
MACHINE
VISION
SYSTEMS
5
0.197
31 25.4
1.220 1.000
Operation indicator (Orange)
PLC
FA
COMPONENTS
CN-EP1
16
(0.630
)
2-M3 × 0.5 0.020
thru-hole threads
ø1.45 ø0.057, single core
two parallel shielded cables
Laser emission indicator (Green)
25
0.984
3 0.118
1
0.039
15.5
0.610
31 25.4
Beam emitting / 1.220 1.000
receiving part
LS-H21(-A) LS-H21F(-A)
LASER
MARKERS
ENERGY
MANAGEMENT
SOLUTIONS
11.2
0.441
8.8
0.346
2,000
(78.740
)
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
Sensor head
Operation indicator (Orange)
Laser emission indicator (Green)
25
0.984
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
LS-H92 LS-H92F
Operation indicator (Orange)
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
The CAD data can be downloaded from our website.
3
0.118
7.2
0.283
2.65
0.104
2.54
0.100
7
0.2 0.276
0.008
10
0.394
13.6
0.535
7.2
0.283
3
0.118
Digital Laser Sensor
DIMENSIONS (Unit: mm in)
MS-DIN-E
LS-400 SERIES
The CAD data can be downloaded from our website.
End plate (Optional)
RF-230
Reflector [Accessory for LS-H92(F)]
3
0.118
15
0.591
AREA
SENSORS
49.3
59.3 1.941
2.335
5.6 M3 square nut
0.220
(
32
1.260
10 0.394
4
0.157
Suitable for 35 mm 1.378 in width DIN rail
)
PRESSURE /
FLOW
SENSORS
5 0.197
3.3
0.130
40
1.575
Material: Polycarbonate
Reflector (Accessory for LS-H91□)
SENSOR
OPTIONS
2-ø4.6 ø0.181
mounting holes
RF-310
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
8.3
0.327
Material: Acrylic (Reflector)
ABS (Base)
RF-330
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
30
1.181
24.7
0.972
1.6
0.063
LASER
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
M3 (length 18 mm 0.709 in) pan head screws
60
2.362
FIBER
SENSORS
PHOTOELECTRIC
SENSORS
50.3
1.980
2.75
0.108
3
0.118
226
Reflector (Optional)
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
2-ø3.2 ø0.126
mounting holes
30 1.181
24 0.945
45 37 23
1.772 1.457 0.906
8
0.315
7
0.276
5.5 0.217
4.2 0.165
12
0.472
2-ø3.2 0.126
mounting holes
3.2
0.126
HUMAN
MACHINE
INTERFACES
Material: Acrylic (Reflector)
ABS (Base)
RF-33 RF-31
Reflective tape (Optional)
Amplifier mounting bracket (Optional)
21.6 0.850
16 0.630
5.2
0.205
10
0.394
Model No.
A
B
RF-33
25.2
0.992
27.8
1.094
RF-31
9.2
0.362
9.2
0.362
3.2
0.126
0.4
0.016 ø1.8
ø0.071
7.5
0.295 4.2 0.165
35
1.378
2
0.079
2
0.079
5.2
0.205
UV
CURING
SYSTEMS
5
0.197
t1
t 0.039
2-ø3.2 ø0.126 holes
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
3.2
0.126
8.5
0.335
Adhesive tape
A
ENERGY
MANAGEMENT
SOLUTIONS
MS-DIN-2
0.4
0.016
B
STATIC
CONTROL
DEVICES
PLC
7
0.276
Material: Acrylic (Reflector)
ABS (Base)
MEASUREMENT
SENSORS
LASER
MARKERS
13.6
0.535
24
17.2
0.945 0.677
32
1.260
4
0.157
27
1.063
Selection
Guide
Amplifier
Built-in
Amplifierseparated
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
LS-500
MS-CX-1
Sensor head mounting bracket (Optional)
8
0.315
5
0.197 6
0.236
20
0.787
13.8
0.543
R20 R0.787
Sensor head mounting bracket (Optional)
t 1.2
t 0.047
3.5
3.4
0.138 0.134
30 1.181
22
0.866
7°
7°
7°
14
0.551
3.4
0.134
Material: Stainless steel (SUS304)
30 1.181
22 0.866
10°
Two M3 (length 12 mm 0.472 in)
screws with washers are attached.
t 1.2
t 0.047
MS-CX-2
25
41 0.984
1.614
R25
R0.984
3.4 0.134
2-ø3.3 ø0.130 holes
3.4
0.134
10
0.394
19
0.748
12.5
0.492
10°
2.5
0.098
39
1.535 54
2.126
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in)
screws with washers are attached.
25
0.984
7°
7.5
0.295
7°
5
0.197
R25 R0.984
4-ø3.3 ø0.130 holes
4.5
7.5 0.177
0.295
25
10
0.394 0.984
R20 R0.787
3.2
0.126
20
0.787
3.2
0.126
6
0.236
LS-400
227
FIBER
SENSORS
LASER
SENSORS
Digital Laser Sensor
DIMENSIONS (Unit: mm in)
MS-CX-3
Sensor head mounting bracket (Optional)
10
0.394
30
1.181
3.5
20.5
0.138
0.807
3.4
R25 10° 0.134
R0.984
3.4
0.134
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
5
0.197
8
0.315
3.4
0.134
PARTICULAR
USE
SENSORS
R25
R0.984
10°
15
0.591
32 1.260
20 0.787
5.5
0.217
14
0.551
8.5
0.335
6
0.236
5
0.197
6
0.236
Two M3 (length 12 mm 0.472 in)
screws with washers are attached.
60°
4
0.157
4.5 0.177
3.4
0.134
6
0.236
13
0.512
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
MS-CX-11
10°
25
0.984 R7.5
t 1.2
R0.295
t 0.047 12.5
0.492
Material: Stainless steel (SUS304)
6
0.236
ø36 ø50
ø1.417 ø1.969
Material: Stainless steel (SUS304)
18
0.709
3.4
25
35
0.134 0.984 1.378
INDUCTIVE
PROXIMITY
SENSORS
WIRE-SAVING
SYSTEMS
MS-CX-4
t 1.2
t 0.047
MICRO
PHOTOELECTRIC
SENSORS
SIMPLE
WIRE-SAVING
UNITS
The CAD data can be downloaded from our website.
Sensor head mounting bracket (Optional)
PHOTOELECTRIC
SENSORS
SENSOR
OPTIONS
LS-400 SERIES
4 0.157
R25
R0.984
0.5
0.020
R7.5
R0.295 46
1.811
25
0.984
Sensor mounting bracket for beam axis alignment (Optional)
MEASUREMENT
SENSORS
2.5 0.098
9
0.354
STATIC
CONTROL
DEVICES
20.3
0.799
Horizontal adjustment range
2-ø3.5 ø0.138
M3 (length16 mm 0.630 in)
horizontal adjustment screw
LASER
MARKERS
10.5 14.5
0.413 0.571
13
0.512 40
1.575
PLC
HUMAN
MACHINE
INTERFACES
(
4°
)
Center of beam axis
13
0.512
1.8
0.071
M4 (length16 mm 0.630 in) angle fixing screw
M3 (length16 mm 0.630 in)
vertical adjustment screw
ENERGY
MANAGEMENT
SOLUTIONS
52.8
2.079
FA
COMPONENTS
25.4
1.000
Vertical adjustment range
55
2.165
4°
2-ø3.5 ø0.138
20.4
( 0.803
)
MACHINE
VISION
SYSTEMS
24.6
0.969
12 0.472
12 0.472
5
0.197
UV
CURING
SYSTEMS
37.3
1.469
8
0.315
11.5
0.453
40
1.575
48
1.890
Material: Zinc die-cast
Selection
Guide
Two M3 (length 14 mm 0.551 in)
screws with washers are attached.
Amplifier
Built-in
Amplifierseparated
MS-RF23
Reflector mounting bracket for RF-230 (Optional)
40
1.575
LS-500
LS-400
3
(0.118
)
Assembly dimensions
4.5
0.177
10
0.394
4.5
0.177
11
0.433
50
1.969
40
1.575
5 0.197
50.3
1.980
8.3
0.327
15 0.591 61
2.402
35
1.378
t2
t 0.079
18 0.709
12
0.472
(
28.3
19.3 1.114
0.760
10
0.394
16 0.630
3
0.118
40
1.575
7 0.276
)
26
1.024
28
1.102
(
)
20
0.787
(
Two M4 (length 10 mm 0.394 in) screws with washers are attached.
30
(1.181
)
)
8-M4 × 0.7 0.028 thru-hole threads
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
49.3
1.941
61.3
2.413
37
1.457
7
0.276
10
0.394
40
1.575
5
0.197
t2
t 0.079
Digital Laser Sensor
DIMENSIONS (Unit: mm in)
MS-AJ1
11.8
0.465
20 0.787
6 0.236
Cable guide
(POM)
(
(
Sensor mounting bracket
[Stainless steel (SUS304)]
)
147
5.787 (Note)
218
8.583
)
Cable guide
(POM)
44.5
(1.752
) 28
4.2 0.165
M4 hexagonsocket-head
bolt
20
0.787
45
1.772
Base
(PA)
Two M3 (length 14 mm 0.551 in) screws
with washers, two M3 (length 16 mm
0.630 in) screws with washers, two M3
(length 18 mm 0.709 in) screws with
washers, one auxiliary mounting plate for
EQ-20 series and one auxiliary mounting
plate for EX-40 series are attached.
25.5
1.004
32
1.260
10
0.394
2-ø6.6 ø0.260 mounting holes
Note: The dimensions in the brackets indicate the adjustable range of the
movable part.
1
20
0.787 0.039
147
(5.787
)(Note)
210
(8.268)
AREA
SENSORS
45°
4.2 0.165
M4 hexagonsocket-head
bolt
Sensor mounting bracket
[Stainless steel (SUS304)]
SENSOR
OPTIONS
10
0.394
SIMPLE
WIRE-SAVING
UNITS
24.5
0.965
Base
(PA)
Two M3 (length 14 mm 0.551 in) screws
with washers, two M3 (length 16 mm
0.630 in) screws with washers, two M3
(length 18 mm 0.709 in) screws with
washers, one auxiliary mounting plate for
EQ-20 series and one auxiliary mounting
plate for EX-40 series are attached.
31
1.220
15
8
0.591 0.315
PRESSURE /
FLOW
SENSORS
PARTICULAR
USE
SENSORS
2-ø6.6 ø0.260
mounting holes
32
1.260
46
1.811
20
0.787
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
INDUCTIVE
PROXIMITY
SENSORS
ø10 ø0.394 pipe
[Stainless steel (SUS304)]
20
0.787
LASER
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
45°
3.2
0.126
FIBER
SENSORS
PHOTOELECTRIC
SENSORS
28 20
1.102 0.787
4
0.157
25 20
33
1.299 0.984 0.787
Attachment
(Nylon 6)
36.5
(1.437
)
18
0.709
1.102
17.8
0.701 12
2-ø3.4 ø0.134
0.472 mounting holes
t2
2-3.2
0.126×4.2 0.165
t 0.079
elongated holes
1 0.039
45°
ø10 ø0.394 pipe
[Stainless steel (SUS304)]
8
0.315
Universal sensor mounting stand (Optional)
11.8
0.465
20 0.787
6 0.236
45°
3.2
0.126
1
0.039
Attachment
(Nylon 6)
MS-AJ2
28 20
1.102 0.787
4
0.157
33 25 20 20
1.299 0.984 0.7870.787
228
The CAD data can be downloaded from our website.
Universal sensor mounting stand (Optional)
17.8
0.701 12
2-ø3.4 ø0.134
0.472
mounting holes
t2
2-3.2
0.126×4.2 0.165
t 0.079
elongated holes
1 0.039
LS-400 SERIES
Note: The dimensions in the brackets indicate the adjustable range of the
movable part.
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
MS-AJ1-A
16.5
0.650
Universal sensor mounting stand (Optional)
28.45
1.120
6 0.236
Cable guide
(POM)
28
1.102
(
12
0.472
)
33
(1.299
)
Sensor mounting bracket
[Stainless steel (SUS304)]
(Note 2)
Arm joint
(Nylon 6)
147
2-ø3.4 ø0.134
5.787
mounting holes
ø10 ø0.394 pipe
(Note 1)
[Stainless steel (SUS304)]
2-3.2 0.126×4.2 0.165
elongated holes
(
218
(8.583
)
210
8.268
134
5.276 (Note 1)
4.2 ø10 ø0.394 pipe
0.165 [Stainless steel (SUS304)]
33
1.299
( )
32
10
1.260
0.394
2-ø6.6 ø0.260 mounting holes
28.45
1.120
Cable guide
(POM)
Base
(PA)
Two M3 (length 14 mm 0.551 in) screws
with washers, two M3 (length 16 mm
0.630 in) screws with washers, two M3
(length 18 mm 0.709 in) screws with
washers, one auxiliary mounting plate for
EQ-20 series and one auxiliary mounting
plate for EX-40 series are attached.
Notes: 1) The dimensions in the brackets indicate the adjustable range of the
movable part.
2) Refer to MS-AJ1 / MS-AJ2 for the assembly dimensions with the
sensor mounting bracket, sensor or reflector.
31
1.220
8
15
0.591 0.315
)
134
5.276 (Note 1)
4.2 ø10 ø0.394 pipe
0.165 [Stainless steel (SUS304)]
12
0.472
(
20
0.787
(
210
8.268
33
(1.299
)
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
)
UV
CURING
SYSTEMS
10
0.394
36.5
(1.437
)
32
1.260
46
1.811
20
0.787
16.5
(0.650
)
33
1.299
Sensor mounting bracket
[Stainless steel (SUS304)]
(Note 2)
Arm joint
(Nylon 6)
147
2-ø3.4
ø0.134
5.787
mounting holes ø10 ø0.394 pipe
(Note 1)
[Stainless steel (SUS304)]
2-3.2 0.126×4.2 0.165
elongated holes
210
(8.268
)
(203.5
8.012)
Base
(PA)
Universal sensor mounting stand (Optional)
6 0.236
18
0.709
44.5
1.752
25.5
1.004
16.5
0.650
(16.5
0.650)
)
20
8
0.787
45
0.315
1.772
MS-AJ2-A
2-ø6.6 ø0.260
mounting holes
(208.5
8.209)
24.5
0.965
Two M3 (length 14 mm 0.551 in) screws with
washers, two M3 (length 16 mm 0.630 in) screws
with washers, two M3 (length 18 mm 0.709 in)
screws with washers, one auxiliary mounting
plate for EQ-20 series and one auxiliary mounting
plate for EX-40 series are attached.
Notes: 1) T
he dimensions in the brackets indicate the adjustable range of the
movable part.
2) Refer to MS-AJ1 / MS-AJ2 for the assembly dimensions with the
sensor mounting bracket, sensor or reflector.
Selection
Guide
Amplifier
Built-in
Amplifierseparated
LS-500
LS-400
工商网监
湘ICP备2023018690号
