501
FIBER
SENSORS
Safety Light Curtain
Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Related Information
■■General terms and conditions.............. F-3
■■Glossary of terms / General precautions.... P.1549~ / P.1595
■■Selection guide...............................P.457~
■■Korea’s S-mark / KC-mark............. P.1602
LASER
SENSORS
PHOTOELECTRIC
SENSORS
Ver.2
Certified
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
Conforming to
OSHA / ANSI
Listing
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Conforming to GB/T 4584
(Excluding SF4B-□-03)
Certified
(SF4B-□ only)
(SF4B-□-03 only)
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
Category 4 PLe SIL3
The control category differs depending on the configuration and wiring of the external circuit.
Protection structure IP67
New version with improved environmental resistance performance
It is possible to select from each three types of standard / robust types depending on the worksite
A wide range of variations are available with protective heights of 230 to 1,910 mm 9.055 to 75.197 in
(1,270 mm 50.000 in for the finger protection type). Mixing six types in a series connection is also possible.
Finger protection type
MACHINE VISION
SYSTEMS
SF4D
SF4B/
SF4B-G
SF4B-C
SF2B
Hand protection type
SF4B-H□(G□)
Arm / Foot protection type SF4B-A□(G□)
Minimum sensing object
Minimum sensing object
mm
mm
ø0.551 in
mm
mm
ø0.984 in
mm
mm
ø1.772 in
ø25
(10 mm 0.394 in beam pitch)
ø45
(20 mm 0.787 in beam pitch)
(40 mm 1.575 in beam pitch)
* In the case of “When used as safety device for presses in China”, the protective height differs. For details, refer to p.509~ / p.534~ and “Definition of
sensing heights” (p.645).
Global support for the safety of press machines or shear (paper cutting) machines
Can be widely used for press machines and other types of equipment from Japan, Europe, North America, South Korea, and China.
Type
Model No.
SF4B-□
SF4B-□G
SF4C
BSF4-AH80
SF4B-F□(G□)
Minimum sensing object
ø14
UV CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
panasonic.net/id/pidsx/global
Safety
light
curtains
SF2C
Definition of
Sensing Heights
Control
units
SF4B-A□-01
SF4B-H□-01
SF4B-H□G-01
SF4B-F□-01
SF4B-□-03
Machinery EMC
UL
Japanese Press
Japanese Shear
S-mark
Directive Directive Certified Machine Support (Paper Cutter) Support certification
●
●
●
●
●
●
●
● (No.TA523)
● (No.TA521)
●
●
●
●
●
●
SF-C11
●
●
●
SF-C12
●
●
●
SF-C13
●
●
●
SF-C14EX
●
●
●
SF-C14EX-01
●
●
●
● (No.TA524)
Korean Press /
Cutting Machine
● : Available
Chinese GB
Compatibility
●
●
●
● (No.TA522)
●
●(No.09-AV4BI-0001 to 0009)
(No.TA525) (Note 1)
●
(No.TA526) (Note 2)
●
●
(No.TA527) (Note 1)
(No.TA528) (Note 2)
●
●
(No.TA529) (Note 1)
(No.TA530) (Note 2)
Notes: 1) In combination with SF4B-A□-01.
2) In combination with SF4B-H□-01 / SF4B-H□G-01 / SF4B-F□-01.
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
APPLICATIONS
502
FIBER
SENSORS
Detecting the intrusion and
presence of a human being
Detecting the intrusion of a human being: Example 1
The safety light curtains allow you to discriminate between a workpiece
and a human being by performing muting control for each beam axis.
Detecting the intrusion of a human being: Example 2
By using the fixed blanking function,
obstacles that always exist are ignored.
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
A unified response time of 14 ms for all models makes calculation work easy
A fast response time of 14 ms has been achieved regardless of the number of beam channels, the beam axis pitches
and the number of units connected in series. This reduces calculation work required for the safety distance.
14 ms even in case of 3 units connected in series!
Safety distance
Safety distance (Note)
the machinery’s
maximum stopping time
Finger protection type
or
STATIC
CONTROL
DEVICES
Series connection allows max. 3 sets or a total of
up to 192 beam axes.
116 mm*4.567 in
Dangerous source
Safety distance
Characteristic
distance for
safety light
curtain
SIMPLE
WIRE-SAVING
UNITS
MEASUREMENT
SENSORS
Hand protection type
28 mm* 1.102 in
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
Same response
Characteristic distance for
time of
14 ms
PARTICULAR
USE SENSORS
LASER
MARKERS
PLC
(Note)
Characteristic distance
for the machinery’s
maximum stopping time
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
SF4B series
Characteristic distance
for SF4B series
* It is the characteristic distance for safety light curtain based on ISO 13855.
Note: Calculate the safety distance based on the distance depending on the safety light curtain and the distance depending on the maximum halting
time of machinery. Install the safety light curtain according to the relevant standards of the region where the safety light curtain is used.
Improved environmental resistance performance and easier operability
New structure
Protection structure IP67 in a very compact size
A seamless structure with minimal joints has now been developed. The inner unit is protected by a cylindrical inner
case. Seams on the unit and lens surfaces have been greatly reduced so that particles such as oil mists and dust are
prevented from penetrating the case. Thus, the environmental resistance performance could be raised.
Slim
28 mm 1.102 in
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Inner case
Cylindrical inner case
protects the internal unit.
This new structure does not use adhesive
or double-sided tape on the joints like
with the previous models. There is no
need to worry about water immersion
or corrosion such as a coolant causing
the adhesive to strip off.
SF4B / SF4B-G series Ver.2 has passed the tests of IP65 and IP67 as specified by IEC / JIS standards.
503
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Error details can be understood at a glance with a digital error indicator
The system constantly checks the safety light curtain for
problems such as incorrect cable wiring, disconnection,
short-circuits, internal circuit problems, and incoming light
problems. Details of any electrical problems such as at
equipment startup will appear on the digital display. It is
no longer necessary to count the number of times the LED
blinks, making the system much more convenient.
Angle of view is wider and
indicators are even more visible
Error number notification means smooth support via telephone
Normal operation
Breaking out error
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
Digital error
indicator
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
A muting control function is provided to increase both safety and productivity
The safety light curtain is equipped with
a muting control function that causes the
line to stop only when a person passes
through the safety light curtain, and does
not stop the line when an object passes
through. The muting sensors and muting
lamps can be connected directly to the
safety light curtain so that a exclusive
controller is not required for muting. This
both reduces costs and increases safety
and productivity.
(excluding SF4B-□-03)
Muting sensors
Muting
lamps
Safety light
curtain
SF4B series
Muting lamps
SF4B
series
External device
(Force-guided relay, etc.)
Muting sensors
CX-400 series
UV CURING
SYSTEMS
Motor, etc.
Override function allows the line to be restarted smoothly after it has stopped while muting control was active
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
(excluding SF4B-□-03)
In case the power turns off while the
Example: When power turns off while safety light curtain was interrupted
safety light curtain has been interrupted
SF4B series
Previous model
by an object or in case the line stops
before the muting conditions have been
established (if only one muting sensor has
Removal
No removal
been interrupted), the line can be restarted
operation
necessary
required
smoothly without having to remove the
object that is interrupting the safety light
curtain.
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Object must be removed before restart
Smooth restart
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Equipped with a safety circuit that does not require an exclusive safety relay unit
The safety light curtain has a built-in
external device monitoring function (such
as for monitoring whether relays have
fused) and an interlock function. The
safety circuit is built without safety relay
unit and size reduction of a control board
is achieved, which contributes to cost
reduction.
Previous model
PHOTOELECTRIC
SENSORS
Monitor
MICRO
PHOTOELECTRIC
SENSORS
External devices
(Force-guided relay, etc.)
Motor, etc.
SF4B series
Reset input
No safety relay
unit needed
Smaller
control board
Monitor
Built-in external
device monitoring
function
SF4B series
External devices
(Force-guided relay, etc.)
Motor, etc.
Note: Contact Panasonic Corporation for details on the recommended products.
Beam-axis alignment indicators show the incident light position at a glance
Beam-axis alignment indicators display the beam channels of the safety light curtain in four blocks. When the beam
channel at the bottommost channel (or topmost channel), which is used as a reference for beam-axis alignments, is
correctly aligned, the LED blinks red. After this, each block lights red as the beam axes successively become aligned.
When all channel beam axes are aligned, all LEDs light green. The display also has an additional stability indicator
(STB) so that setup can be carried out with greater stability.
3 block
Blinking
A
B
C
D
Light
up
OSSD
STB
A
B
C
D
Light
up
OSSD
STB
Light
up
2 block
OSSD
STB
1 block
OSSD
STB
A
B
C
D
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
All beam axes
are aligned
4 block
The beam axes of the two
lower blocks are aligned
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
DIN terminal block
SFS4-SFD (AG1S847) [4-poles type]
SFS6-SFD (AG1S867) [6-poles type]
A
B
C
D
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
SIMPLE
WIRE-SAVING
UNITS
SF relay, slim type
SFS3-L-DC24V (AG1S132)
SFS4-L-DC24V (AG1S142)
The bottommost beam
axis is aligned
AREA
SENSORS
PARTICULAR
USE SENSORS
◦Safety relay
Panasonic Corporation
SF relay, slim type
Beam axes are
displayed in 4 blocks
FIBER
SENSORS
LASER
SENSORS
Reset input
Safety light curtain Safety relay unit
504
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
The bottommost LED ‘D’
is blinking red
The two bottom LEDs ‘C, D’
light up in red
All LEDs ‘A to D’
light up in green
Furthermore, STB display
allows the most stable incident
light status* to be confirmed.
* 140 % or more incident light intensity
of control output operation level
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
505
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Supports both PNP and NPN polarities in a single model
The SF4B / SF4B-G series combines PNP transistor output and NPN transistor output in a single model. Overseas
equipment that uses PNP, replacement with NPN sensors, factories that are positively grounded, and transfer of
equipment overseas are all situations where the control circuits for a single model are suitable for use a.
■ Polarity can be changed easily by changing wiring
When the output polarity setting wire (shielded) is
connected to 0 V, PNP output is selected, and when it
is connected to 24 V, it switches to NPN output.
PNP circuit
0V
NPN circuit
24 V
Output polarity setting wire (Shield)
Control output (OSSD)
Connect to 0 V
Connect to 24 V
Not connected / open
PNP output
NPN output
Error
Laser alignment tool for easy installation
The tool performs beam-axis alignment using a laser
beam spot. As the tool is battery-operated, it is possible
to perform beam-axis alignment before supplying power
to the equipment.
Laser alignment tool
The topmost beam axis
is correctly aligned
LASER
MARKERS
Visible red spot!
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
The bottommost channel beam axis
is correctly aligned
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
PNP/NPN polarity indicator
Either PNP or NPN side lights
depending on which is selected.
Output polarity setting wire (Shield)
Greatly improved ease of installation
New structure
(excluding SF4B-□G□)
The hexagon-socket head bolts used for aligning the
beam axis can be accessed from the front of the safety
light curtain. Beam adjustment can be carried out easily
while turning
the bolts.
360° rotation
Hexagon-socket
when used with M5 hexagon-socket
Also, the
head bolt for beam-axis head bolt for alignment
alignment (up to ±15˚)
beam-axis
alignment
part is directly
and firmly
fixed with M5
bolts so that
Hexagon-socket
head bolt for alignment
beam axes
(360˚ rotation for every 30˚)
misalignment
can be
Mode
Made of die-cast!
Hexagonal wrench
prevented.
Align at the front!
Direct fixing to prevent misalignment!
Few number of bolts!
Easy to distinguish receiver and emitter
Emitter is gray, receiver is black. Whether during startup
or maintenance, troubles due to incorrect wiring or false
recognition can be greatly reduced. Moreover, the model
No. can be checked at the front face of the safety light
curtain.
Black connector Gray cable with black line Black cover
RECEIVER
Receiver
Model No. is shown on the front face of the sensor
Emitter
Gray connector
Gray cable
Gray cover
EMITTER
Mutual interference is reduced without
needing interference prevention lines
Reducing the number of malfunctions
caused by extraneous light
The safety light curtain is equipped with the ELCA
(Extraneous Light Check & Avoid) function. Because
it automatically shifts the scan timing of the safety
light curtain in order to avoid interference, it is not
necessary to wire interference prevention lines between
machineries.
Double scanning method and retry processing are
two new functions exclusive to our company, which
successfully eliminate the effects of momentary
extraneous light from peripheral equipment. The
reduction in operating errors caused by extraneous light
reduces frequent stopping of machinery.
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Resistant to impact, less damage to workpiece
Robust type SF4B-□G□
Thick and robust housing resistant to impact
No guard needed
The SF4B-G series safety light curtain is enclosed in a 5 mm
0.197 in thick robust metal case, protecting the workpiece from
various types of impact, such as collision or being stepped on.
The robust type can be used without
an L-shape or U-shape guard, reducing
installation and maintenance.
Stepped on - Kicked
Collision –Impact
Average
thickness
5 mm
U-shape /
L-shape guard
Front protection cover
Fully protected sensing surface
The sensing surface is fully protected by narrowing and deepening
the exposed area of the sensing surface.
Previous product
SF4B-□G□
Collision with sensing surface
Sensing surface protected
Narrow
The front protection cover protects the
sensing surface from welding spatter and
reduces damage
due to collisions.
Front protection
The beam axis
cover
adjuster can be
attached without
removing the front
protection cover.
Deep
Protection structure IP67
The seamless structure protects the sensor
from being exposed to water.
Round design minimizes damage to the workpiece
Mounting bracket for simple & secure installation
The case is designed so that shock upon impact is
dissipated alleviating potential damage to the workpiece
in the event of a collision.
The safety light curtain and the mounting bracket are
firmly secured with just two bolts. The safety light curtain
is situated in the
Thickness
center of the
mounting bracket,
mm
preventing beam
0.157 in
axis deviation. The
M5 bolt × 2
dimple structure
makes alignment
M5 beam axis
easy to adjust.
SF4B-□G□
Previous product
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
0.197 in
Loads applied –Dropped
506
4
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
adjustment bolt
Dimple structure
Large impact on collision
Small impact on collision
M8 center
attachment bolt
Workpiece not contaminated with paint
Black and yellow caution tape
The body has an alumite-treated case so that paint does
not stick to the workpiece in the event of a collision.
Black and yellow striped attention tape is attached to the
side of the safety light curtain, alerting workers to use
caution. Hazardous openings are very obvious.
Enables series connection with standard type possible
The mating cable is standard, allowing the robust and
standard types to be connected in series.
Caution tape
・SF-TP-BG10
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Standard type
Robust type
Standard type
Use robust type only for required sections
Special tape
• Fit to width of safety light curtain
• Made of fabric, making it easy to cut
• Prevent damage at the time of collision
507
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
A large reduction in cost by using corner mirror (optional)
A single corner mirror makes it possible to
eliminate one safety light curtain set and its
associated peripheral safety circuits.
This enables costs to be greatly reduced,
and also eliminates wiring needs. The
control category is unchanged.
Corner mirror
RF-SFBH-□
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
Normally for L-shaped or U-shaped
installation, 2 or 3 sets of safety
light curtains are needed. With the
use of a corner mirror reflecting
the light, one set of safety light
curtain is possible for L-shaped or
U-shaped installation.
Handy-controller SFB-HC (optional) that enables the user to select a variety of settings
Separate muting control function for each beam channel
The handy-controller SFB-HC* (optional) can be used
to carry out muting control for specified beam axes only.
Because individual beam axes can be specified to suit
the object, separate guards to prevent entry do not need
to be set up.
Line stopped
While muting control is active (line operating)
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
SFB-HC
For example, depending on the height of the object, the muting function
can be activated for 10 beam channels starting from the bottom, so that if
the 11th or subsequent beam channels are interrupted, it is judged that a
person has entered the area and the line stops.
*A
handy-controller cannot be used with the
SF4B-□-01(p.509), SF4B-□-03(p.509) and the
SF-C14EX-01(p.514 / p.663).
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Specific beam axes can be deactivated
The SF4B / SF4B-G series incorporates a fixed blanking function.
A variable number of beam axes can be deactivated
The SF4B / SF4B-G series incorporates a floating blanking function.
The SF4B / SF4B-G series is
equipped with a fixed blanking
function which allows specific
beam channels to be selectively
interrupted without causing the
control output (OSSD) to output
the OFF signal. This function
is convenient for use with
applications in which certain fixed
obstacles tend to block specific
beam channels.
Furthermore, this function provides
greater safety as the control
output (OSSD) will automatically
output the OFF signal if the fixed
obstacles are subsequently
removed from the sensing area.
1, 2 or 3 non-specified
beam channels can be
deactivated. If the number
of beam channels that are
blocked is less than or
equal to the set number of
beam channels, then the
control output (OSSD) will
not output the OFF signal.
This function is useful in the
event when the positions of
obstacles within the sensing
area must be changed
during object rearrangement,
or when an object passes
through the safety light
curtain’s sensing area.
Selectable configuration for auxiliary output
A variety of other functions can be selected
Mode No.
0
1
2
3
4
5
6
7
8
9
Description
Negative logic of the control output (OSSD 1, OSSD 2) (factory setting)
Positive logic of the control output (OSSD 1, OSSD 2)
For emission: output ON, For non-emission: output OFF
For emission: output OFF, For non-emission: output ON
For unstable incident beam: OFF (Note 1)
For unstable incident beam: ON (Note 1)
For muting: ON
For muting: OFF
For beam received: ON, For beam interrupted: OFF (Note 2)
For beam received: OFF, For beam interrupted: ON (Note 2)
Notes: 1) The output cannot be used while the fix blanking function,
floating blanking function or the muting function is activated.
2) This device outputs the beam received/interrupted state at the
detectable area regardless of fixed blanking function, floating
blanking function, and muting function.
Note: When the floating blanking
function is used, the acceptable
size for the minimum sensing
object changes.
Emission intensity control function
This function reduces the amount of emitting light.
The two modes, normal mode and short mode, can be
selected (factory setting: normal mode).
Monitoring function
This function allows the user to confirm the details of
each safety light curtain setting.
Protection function
A password protection can be used to avoid
unauthorized changes of the settings (factory setting:
no password protection).
Copy function
Setting details can be copied to other safety light curtains.
This is helpful if you need the same settings on different devices.
Muting lamp diagnosis setting
When the muting lamp diagnosis is disabled, the muting
function will continue to operate even if the lamp is blown.
* Refer to the instruction manual for details.
The instruction manual can be download from our website.
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Lineup of exclusive control units
508
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
SF-C10 series
PRESSURE /
FLOW
SENSORS
SF-C13
Supports both PNP and NPN polarities SF-C10 series
Thin control unit
The SF4B / SF4B-G series enables the changeover of PNP/
NPN inputs in a single model for reduction of registered
model No.
22.5 mm 0.886 in thinness has been realized. Possible to
install in a small space of the board.
Connector connection control unit
SF-C11
The wiring with the safety light curtain is simple connector
connection. It reduces time for installation and replacement.
SF-C14EX(-01)
Application expansion unit
The three safety systems; safety light curtain output, muting
control, emergency stop button have been integrated into a
single unit.
SF-C12
Robust type control unit
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
The safety relay is built in the robust metal casing. As the
protection structure is IP65, it is possible to install SF-C12
independently without putting it into the control board.
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
PRODUCT CONFIGURATION
ENERGY
MANAGEMENT
SOLUTIONS
Mounting bracket and mating
cable are optional.
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
Muting control components (12-core cable, with interference prevention wire)
Standard components (8-core cable)
Component parts
7
Required
1
Safety light curtain
2
Mounting bracket (Optional)
3
Component parts
7
1
Safety light curtain
2
Mounting bracket (Optional)
8-core bottom cap cable (Optional)
5
12-core bottom cap cable (Optional)
Selection
Guide
4
8-core extension cable
(Optional, use for cable extension)
6
12-core extension cable
(Optional, use for cable extension)
Safety Light
Curtains
7
Cable for series connection
(Optional, use for connection in series)
7
Cable for series connection
(Optional, use for connection in series)
1
3
4
2
Required
1
5
6
2
Using SF4B-□-01 as a safety device for a press or shearing machine (paper cutting machine) in Japan (See the above when using SF4B-□-01 as a safety device for other types of machine)
Standard components (8-core cable)
Required
1
2
1
Safety light curtain
2
Mounting bracket (Optional)
8
9
12
8
Muting control components (12-core cable, with interference prevention wire)
Component parts
12
UV
CURING
SYSTEMS
Component parts
12
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
1
Safety light curtain
SF2C
2
Mounting bracket (Optional)
8-core bottom cap cable (Optional)
10
12-core bottom cap cable (Optional)
Definition of
Sensing Heights
8-core extension cable
(Optional, use for cable extension)
11
12-core extension cable
(Optional, use for cable extension)
12
Cable for series connection
(Optional, use for connection in series)
Required
1
Cable for series connection
(Optional, use for connection in series)
9
10
2
11
509
Safety Light Curtain Type 4
ORDER GUIDE
FIBER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
1 Safety light curtains (Standard type) Mounting bracket and bottom cap cable are not supplied with the safety light curtain. Be sure to order them separately.
Type
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
Finger protection type
AREA
SENSORS
SENSOR
OPTIONS
Min. sensing object ø14 mm ø0.551 in
(10 mm 0.394 in beam pitch)
LASER
SENSORS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Appearance
Beam
channel
No.
Number Protective height (mm in)
of
SFB-HC
Korean Press compliant beam
China Press compliant
non‑compatible (SFB-HC non-compatible) channels
(GB/T 4584)(Note 3)
23
230 9.055 220 8.661
SF4B-F23 SF4B-F23-01 SF4B-F23-03
Model No. (Note 2)
Operating
range
(Note 1)
5 mm
0.197 in
Protective height
0.3 to 7 m
0.984 to 22.966 ft
Beam pitch 5 mm
10 mm
0.197 in
0.394 in
SIMPLE
WIRE-SAVING
UNITS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
Hand protection type
MEASUREMENT
SENSORS
ENERGY
MANAGEMENT
SOLUTIONS
Min. sensing object ø25 mm ø0.984 in
(20 mm 0.787 in beam pitch)
WIRE-SAVING
SYSTEMS
Beam
channel
No.
5 mm
0.197 in
0.3 to 9 m
0.984 to 29.528 ft
Protective height
Beam pitch 5 mm
20 mm
0.197 in
0.787 in
FA
COMPONENTS
0.3 to 7 m
0.984 to 22.966 ft
MACHINE
VISION
SYSTEMS
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
Arm / Foot protection type
Selection
Guide
Min. sensing object ø45 mm ø1.772 in
(40 mm 1.575 in beam pitch)
UV
CURING
SYSTEMS
Beam
channel
No.
15 mm
0.591 in
Protective height
Beam pitch
40 mm 1.575 in
15 mm
0.591 in
SF4B-C
0.3 to 7 m
0.984 to 22.966 ft
SF4C
BSF4-AH80
SF2B
SF2C
0.3 to 9 m
0.984 to 29.528 ft
SF4B-F31
SF4B-F31-01 SF4B-F31-03
31
310 12.205
300 11.811
SF4B-F39
SF4B-F39-01 SF4B-F39-03
39
390 15.354
380 14.960
SF4B-F47
SF4B-F47-01 SF4B-F47-03
47
470 18.504
460 18.110
SF4B-F55
SF4B-F55-01 SF4B-F55-03
55
550 21.654
540 21.260
SF4B-F63
SF4B-F63-01 SF4B-F63-03
63
630 24.803
620 24.409
SF4B-F71
SF4B-F71-01 SF4B-F71-03
71
710 27.953
700 27.559
SF4B-F79
SF4B-F79-01 SF4B-F79-03
79
790 31.102
780 30.708
SF4B-F95
SF4B-F95-01 SF4B-F95-03
95
950 37.402
940 37.007
SF4B-F111 SF4B-F111-01 SF4B-F111-03
111
1,110 43.701 1,100 43.306
SF4B-F127 SF4B-F127-01 SF4B-F127-03
127
1,270 50.000 1,260 49.606
SF4B-H12
SF4B-H12-01 SF4B-H12-03
12
230
SF4B-H16
SF4B-H16-01 SF4B-H16-03
16
310 12.205
300 11.811
SF4B-H20
SF4B-H20-01 SF4B-H20-03
20
390 15.354
380 14.960
SF4B-H24
SF4B-H24-01 SF4B-H24-03
24
470 18.504
460 18.110
SF4B-H28
SF4B-H28-01 SF4B-H28-03
28
550 21.654
540 21.260
SF4B-H32
SF4B-H32-01 SF4B-H32-03
32
630 24.803
620 24.409
SF4B-H36
SF4B-H36-01 SF4B-H36-03
36
710 27.953
700 27.559
SF4B-H40
SF4B-H40-01 SF4B-H40-03
40
790 31.102
780 30.708
SF4B-H48
SF4B-H48-01 SF4B-H48-03
48
950 37.402
940 37.007
SF4B-H56
SF4B-H56-01 SF4B-H56-03
56
1,110 43.701 1,100 43.306
SF4B-H64
SF4B-H64-01 SF4B-H64-03
64
1,270 50.000 1,260 49.606
SF4B-H72
SF4B-H72-01 SF4B-H72-03
72
1,430 56.299 1,420 55.905
SF4B-H80
SF4B-H80-01 SF4B-H80-03
80
1,590 62.598 1,580 62.205
SF4B-H88
SF4B-H88-01 SF4B-H88-03
88
1,750 68.898 1,740 68.503
SF4B-H96
SF4B-H96-01 SF4B-H96-03
96
1,910 75.197 1,900 74.803
SF4B-A6
SF4B-A6-01
–
6
230
SF4B-A8
SF4B-A8-01
–
8
310 12.205
280 11.024
SF4B-A10
SF4B-A10-01
–
10
390 15.354
360 14.173
SF4B-A12
SF4B-A12-01
–
12
470 18.504
440 17.323
SF4B-A14
SF4B-A14-01
–
14
550 21.654
520 20.472
SF4B-A16
SF4B-A16-01
–
16
630 24.803
600 23.622
SF4B-A18
SF4B-A18-01
–
18
710 27.953
680 26.772
SF4B-A20
SF4B-A20-01
–
20
790 31.102
760 29.921
SF4B-A24
SF4B-A24-01
–
24
950 37.402
920 36.220
SF4B-A28
SF4B-A28-01
–
28
1,110 43.701 1,080 42.520
SF4B-A32
SF4B-A32-01
–
32
1,270 50.000 1,240 48.819
SF4B-A36
SF4B-A36-01
–
36
1,430 56.299 1,400 55.118
SF4B-A40
SF4B-A40-01
–
40
1,590 62.598 1,560 61.417
SF4B-A44
SF4B-A44-01
–
44
1,750 68.898 1,720 67.716
SF4B-A48
SF4B-A48-01
–
48
1,910 75.197 1,880 74.016
9.055
9.055
220
200
8.661
7.874
Notes: 1) The operating range is the possible setting distance between the emitter and the receiver.
Receiver cannot be
placed in this range
Definition of
Sensing Heights
Emitter
Actual operating range
0.3 m of the safety light curtain
0.984 ft
Setting range of
the receiver
Receiver
9 m 29.528 ft
SF4B-F□, SF4B-H72/H80/H88/H96□, SF4B-A36/A40/A44/A48□,
SF4B-F□G, SF4B-H72G/H80G/H88G/H96G□, SF4B-A36G/A40G/A44G/A48G: 7 m 22.966 ft
Receiver
2) The model No. with “E” on the product label is the emitter, “D” on the label is the receiver.
3) In the case of “When used as safety device for presses in China” the distance between the center of the first beam axis and the center of the last beam
axis of the device becomes the protective height. The Korean press compliant type SF4B-□-03 does not apply. For details, refer to “Definition of
sensing heights” (p.645).
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
510
ORDER GUIDE
FIBER
SENSORS
1 Safety light curtains (Robust type) Mounting bracket and bottom cap cable are not supplied with the safety light curtain. Be sure to order them separately.
Finger protection type
Hand protection type
Min. sensing object ø25 mm ø0.984 in
(20 mm 0.787 in beam pitch)
Min. sensing object ø14 mm ø0.551 in
(10 mm 0.394 in beam pitch)
Type
Appearance
Beam
channel
No.
Operating
range
(Note 1)
11.8 mm
0.465 in
Protective height
0.3 to 7 m
0.984 to 22.966 ft
Beam pitch 11.8 mm
10 mm
0.465 in
0.394 in
Beam
channel
No.
11.8 mm
0.465 in
Protective height
0.3 to 9 m
0.984 to 29.528 ft
Beam pitch 11.8 mm
20 mm
0.465 in
0.787 in
Arm / Foot protection type
Min. sensing object ø45 mm ø1.772 in
(40 mm 1.575 in beam pitch)
0.3 to 7 m
0.984 to 22.966 ft
Beam
channel
No.
21.8 mm
0.858 in
Protective height
0.3 to 9 m
0.984 to 29.528 ft
Beam pitch
40 mm 1.575 in
21.8 mm
0.858 in
0.3 to 7 m
0.984 to 22.966 ft
Model No. (Note 2)
SFB-HC
non‑compatible
Number Protective height (mm in)
of
China Press compliant
beam
(GB/T 4584) (Note 3)
channels
SF4B-F23G
–
23
244 9.606
220 8.661
SF4B-F31G
–
31
324 12.756
300 11.811
SF4B-F39G
–
39
404 15.906
380 14.960
SF4B-F47G
–
47
484 19.055
460 18.110
SF4B-F55G
–
55
564 22.205
540 21.260
SF4B-F63G
–
63
644 25.354
620 24.409
SF4B-F71G
–
71
724 28.504
700 27.559
79
804 31.654
780 30.708
SF4B-F79G
–
SF4B-F95G
–
95
964 37.953
940 37.007
SF4B-F111G
–
111
1,124 44.252
1,100 43.306
SF4B-F127G
–
127
1,284 50.551
1,260 49.606
SF4B-H12G
SF4B-H12G-01
12
244 9.606
220 8.661
SF4B-H16G
SF4B-H16G-01
16
324 12.756
300 11.811
SF4B-H20G
SF4B-H20G-01
20
404 15.906
380 14.960
SF4B-H24G
SF4B-H24G-01
24
484 19.055
460 18.110
SF4B-H28G
SF4B-H28G-01
28
564 22.205
540 21.260
SF4B-H32G
SF4B-H32G-01
32
644 25.354
620 24.409
SF4B-H36G
SF4B-H36G-01
36
724 28.504
700 27.559
SF4B-H40G
SF4B-H40G-01
40
804 31.654
780 30.708
SF4B-H48G
SF4B-H48G-01
48
964 37.953
940 37.007
SF4B-H56G
SF4B-H56G-01
56
1,124 44.252
1,100 43.306
SF4B-H64G
SF4B-H64G-01
64
1,284 50.551
1,260 49.606
SF4B-H72G
SF4B-H72G-01
72
1,444 56.850
1,420 55.905
SF4B-H80G
SF4B-H80G-01
80
1,604 63.150
1,580 62.205
SF4B-H88G
SF4B-H88G-01
88
1,764 69.449
1,740 68.503
SF4B-H96G
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
SF4B-H96G-01
96
1,924 75.748
1,900 74.803
SF4B-A6G
–
6
244 9.606
200 7.874
SF4B-A8G
–
8
324 12.756
280 11.024
SF4B-A10G
–
10
404 15.906
360 14.173
SF4B-A12G
–
12
484 19.055
440 17.323
SF4B-A14G
–
14
564 22.205
520 20.472
SF4B-A16G
–
16
644 25.354
600 23.622
SF4B-A18G
–
18
724 28.504
680 26.772
SF4B-A20G
–
20
804 31.654
760 29.921
SF4B-A24G
–
24
964 37.953
920 36.220
SF4B-A28G
–
28
1,124 44.252
1,080 42.520
SF4B-A32G
–
32
1,284 50.551
1,240 48.819
SF4B-A36G
–
36
1,444 56.850
1,400 55.118
SF4B-A40G
–
40
1,604 63.150
1,560 61.417
BSF4-AH80
SF4B-A44G
–
44
1,764 69.449
1,720 67.716
SF2B
SF4B-A48G
–
48
1,924 75.748
1,880 74.016
SF2C
Differences from standard type
The robust type SF4B-□G□ is different from the standard type SF4B-□ in the following ways:
• Sensing width (protective height) (Note 1) • Profile • Net weight • Mounting bracket • Front protection cover
• Laser alignment tool • Noncompliant with Japanese and Korean press standard (Note 2)
• Noncompliant with Korean regulations
Other specifications, input/output circuits, and options are the same as for the standard type.
Notes: 1) In the case of “When used as safety device for presses in China”, there is no change in the protective height.
2) SF4B-H□G-01 does not comply with Korean press standard only.
3) In the case of “When used as safety device for presses in China” the distance between the center of the first beam axis and the center of the last
beam axis of the device becomes the protective height. For details, refer to “Definition of sensing heights” (p.645).
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
Definition of
Sensing Heights
511
Safety Light Curtain Type 4
ORDER GUIDE
FIBER
SENSORS
LASER
SENSORS
2 Mounting brackets Mounting bracket is not supplied with the safety light curtain. Be sure to order it separately.
PHOTOELECTRIC
SENSORS
Designation
MICRO
PHOTOELECTRIC
SENSORS
PRESSURE /
FLOW
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
For side mounting. Allows the safety light curtain to be mounted at the side with one
M8 hexagon-socket-head bolt. (4 pcs. per set for emitter and receiver)
MS-SFB-1-T2
Can be used as either a rear mounting bracket MS-SFB-7-T or a side mounting
bracket MS-SFB-8-T depending on mounting direction. (4 pcs. per set for emitter and
receiver)
MS-SFB-1
Used to mount the safety light curtain on the rear surface and side surface.
(4 pcs. per set for emitter and receiver)
MS-SFB-1-T
Allows the safety light curtain to be mounted at the rear and side with one M8
hexagon-socket-head bolt. (4 pcs. per set for emitter and receiver)
MS-SFB-4
Used as the mounting bracket when changing over a previous safety light curtain with
a protective height of 200 mm 7.874 in or more to the SF4B series. It is installed using
two M5 hexagon-socket-head bolts. (4 pcs. per set for emitter and receiver)
MS-SFB-4-T
Used as the mounting bracket when changing over a previous safety light curtain with
a protective height of 200 mm 7.874 in or more to the SF4B series. It is installed using
one M8 hexagon-socket-head bolt. (4 pcs. per set for emitter and receiver)
Dead zoneless mounting bracket
(Excluding SF4B-□G□)
(Material: Die-cast zinc alloy)
MS-SFB-3
Mounting with no dead zone is possible so that the mounting bracket does not project
past the protective height. (4 pcs. per set for emitter and receiver)
Standard L mounting bracket
(For SF4B-□G□)
Material: Cold rolled carbon steel (SPCC)
(Trivalent chrome plated)
MS-SF4BG-1
Mounting is possible behind or at the side of the safety light curtain.
Mount with two M5 bolts or one M8 bolt. (4 pcs. per set for emitter and receiver)
Dead zoneless mounting bracket
(For SF4B-□G□)
Material:
Mounting bracket ...Cold rolled carbon steel (SPCC)
(Trivalent chrome plated)
Supporting bracket ...PPS
MS-SF4BG-3
Allows safety light curtains to be installed closely together or in locations with
installation restrictions due to equipment columns or jigs. (4 pcs. per set for emitter
and receiver)
Standard mounting
bracket
M8 mounting
bracket
Pitch adapter bracket
M8 pitch adapter
bracket
M8 rear mounting bracket M8 side mounting bracket
Standard mounting bracket M8 mounting bracket Pitch adapter bracket
• MS-SFB-7-T
• MS-SFB-1-T2
(Rear mounting)
• MS-SFB-1
• MS-SFB-8-T
• MS-SFB-1-T2
(Side mounting)
M8 rear mounting bracket
MS-SFB-7-T
MS-SFB-1-T2 (Rear mounting)
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
MS-SFB-8-T
* Safety light curtain
can revolve 360°
horizontally.
SIMPLE
WIRE-SAVING
UNITS
FA
COMPONENTS
MS-SFB-7-T
360° mounting
bracket
(Excluding
SF4B-□G□)
Material:
Die-cast zinc alloy
INDUCTIVE
PROXIMITY
SENSORS
M5 (length: 18mm 0.709 in)
hexagon-socket-head bolt
Accessory for MS-SFB-7-T
MS-SFB-1-T2
Safety light
curtain
(
)
Sensing
surface
Four bracket set
Four M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
M8 side mounting bracket
MS-SFB-8-T
MS-SFB-1-T2 (Side mounting)
M5 (length: 18mm 0.709 in)
hexagon-socket-head bolt
Accessory for MS-SFB-8-T
MS-SFB-1-T2
Safety light
curtain
Sensing
surface
(
)
Four bracket set
Four M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
Definition of
Sensing Heights
Standard mounting bracket
MS-SFB-1
Four bracket set
Four M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
• MS-SFB-3
Standard L mounting bracket
(For SF4B-□G□)
• MS-SF4BG-1
M8 pitch adapter bracket
MS-SFB-4-T
Safety light
curtain
Sensing
surface
Four bracket set
Four M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
Sensing
surface
Safety light
curtain
• MS-SFB-4-T
M5 (length: 10 mm 0.394 in)
hexagon-socket-head bolt (Accessory)
M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolt
(Accessory for MS-SFB-4-T)
Safety light
curtain
Sensing
surface
Dead zoneless mounting bracket MS-SFB-3
M5 mounting hole
Spacer (Accessory for MS-SFB-3)
Standard L
mounting bracket
(MS-SF4BG-1)
M8 mounting hole
(For mounting in center)
M5 (length: 25 mm 0.984 in)
hexagon-socket-head bolt
(Accessory for MS-SFB-3)
Four bracket set
Four M5 (length: 25 mm 0.984 in)
hexagon-socket-head bolts and
four spacers are attached.
M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolt
(Accessory for MS-SFB-1-T)
M8 mounting
bracket
MS-SFB-1-T
M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolt
(Accessory for MS-SFB-1) Safety light
M5 mounting hole
(for two-point mounting)
Dead zoneless mounting bracket
• MS-SFB-4
• MS-SFB-1-T
M8 mounting hole (for center mounting)
M8 pitch adapter bracket
SF2B
SF2C
Description
For rear mounting. Allows the safety light curtain to be mounted at the rear with one
M8 hexagon-socket-head bolt. (4 pcs. per set for emitter and receiver)
Rear/side
mounting bracket
M8 side mounting
(Excluding
bracket
SF4B-□G□)
Material: Cold rolled
M8 rear/side mounting
carbon steel (SPCC)
bracket set
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
ENERGY
MANAGEMENT
SOLUTIONS
Model No.
M8 rear mounting
bracket
AREA
SENSORS
HUMAN
MACHINE
INTERFACES
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Safety light
curtain
Four bracket set
Eight M5 (length: 10 mm 0.394 in)
hexagon-socket-head bolts are attached.
curtain
Sensing
surface
Four bracket set
Four M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
Pitch adapter
bracket
MS-SFB-4
M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolt
(Accessory for MS-SFB-4)
Safety light
curtain
Sensing
surface
Four bracket set
Four M5 (length: 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
Dead zoneless mounting bracket
(For SF4B-□G□)
• MS-SF4BG-3
When using M5 hexagon- When using M8
socket-head bolt
hexagon bolt
(Rear mounting)
(Rear mounting)
M5 hexagonsocket-head bolt
(Parchase separately.)
Safety light curtain
M8 hexagon bolt
(Parchase separately.)
Safety light curtain
Dead zoneless supporting bracket
Accessory for dead zoneless
mounting bracket
Dead zoneless supporting bracket
Accessory for dead zoneless
mounting bracket
Dead zoneless mounting bracket
MS-SF4BG-3
Dead zoneless mounting bracket
MS-SF4BG-3
Four bracket set
Twelve M5 (length: 8 mm 0.315 in) hexagon-socket-head bolts
and four nut slots are attached.
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
ORDER GUIDE
3
4
5
6
Discrete wire
Bottom cap cable
7 Mating cable / Extension cable / Cables for series connection Mating cable is not supplied with the safety light curtain. Be sure to order it separately.
Appearance
Connector
With connectors on both ends With
connector
For receiver For emitter on one end
Discrete
wire
With connectors on both ends With connector
Connector
on one end
For receiver For emitter
Cable for series
7 connection
3
Exclusive
mating
cable for
SF-C14EX
Adapter cable
3
FIBER
SENSORS
Model No.
SFB-CCB3
SFB-CCB7
SFB-CCB10
SFB-CCB15
3
Extension cable
Bottom cap cable
5
Extension cable
6
Muting control components (12-core cable, with interference prevention wire)
4
Standard components (8-core cable)
Type
512
SFB-CB05
SFB-CB5
SFB-CB10
SFB-CC3
SFB-CC10
SFB-CCJ3E
SFB-CCJ10E
SFB-CCJ3D
SFB-CCJ10D
SFB-CCB3-MU
SFB-CCB7-MU
SFB-CB05-MU
Description (Note 1)
Length: 3 m 9.843 ft
Net weight: 370 g approx. (2 cables)
Length: 7 m 22.966 ft
Net weight: 820 g approx. (2 cables)
Length: 10 m 32.808 ft
Net weight: 1,160 g approx. (2 cables)
Length: 15 m 49.213 ft
Net weight: 1,710 g approx. (2 cables)
Length: 0.5 m 1.640 ft
Net weight: 95 g approx. (2 cables)
Length: 5 m 16.404 ft
Net weight: 620 g approx. (2 cables)
Length: 10 m 32.808 ft
Net weight: 1,200 g approx. (2 cables)
Length: 3 m 9.843 ft
Net weight: 380 g approx. (2 cables)
Length: 10 m 32.808 ft
Net weight: 1,200 g approx. (2 cables)
Length: 3 m 9.843 ft
Net weight: 190 g approx. (1 cable)
Length: 10 m 32.808 ft
Net weight: 580 g approx. (1 cable)
Length: 3 m 9.843 ft
Net weight: 210 g approx. (1 cable)
Length: 10 m 32.808 ft
Net weight: 600 g approx. (1 cable)
Length: 3 m 9.843 ft
Net weight: 420 g approx. (2 cables)
Length: 7 m 22.966 ft
Net weight: 930 g approx. (2 cables)
SFB-CB05-A-P
For SF4-AH□-N
(NPN type)
SFB-CB05-A-N
For SF2-EH□
(PNP type)
SFB-CB05-B-P
For SF2-EH□-N
(NPN type)
SFB-CB05-B-N
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
Used for connecting to the safety light curtain and to an
extension cable or the SF-C11 control unit.
2 cables/set for emitter and receiver
Connector outer diameter: ø14 mm ø0.551 in max.
Used for cable extension or connecting to the SF-C13 control
unit.
2 cables/set for emitter and receiver
Connector outer diameter: ø14 mm ø0.551 in max.
Used for cable extension or connecting to the SF-C11 and
the SF-C14EX control unit.
One each for emitter and receiver
Connector color: Gray (for emitter), Black (for receiver)
Connector outer diameter: ø14 mm ø0.551 in max.
Used for connecting to the safety light curtain and to other
cables or the SF-C13 control unit.
2 cables/set for emitter and receiver
Used for connecting to the safety light curtain and to an
Length: 0.5 m 1.640 ft
extension cable or the SF-C12 control unit.
Net weight:
2 cables/set for emitter and receiver
110 g approx. (2 cables)
Connector outer diameter: ø16 mm ø0.630 in max.
Length: 3 m 9.843 ft
SFB-CC3-MU
Net weight: 430 g approx. (2 cables)
Length: 7 m 22.966 ft
SFB-CC7-MU
Net weight: 1,000 g approx. (2 cables)
Length: 10 m 32.808 ft
SFB-CC10-MU
Net weight: 1,300 g approx. (2 cables)
Length: 3 m 9.843 ft
SFB-CCJ3E-MU Net weight: 190 g approx. (1 cable)
Length: 10 m 32.808 ft
SFB-CCJ10E-MU Net weight: 660 g approx. (1 cable)
Length: 3 m 9.843 ft
SFB-CCJ3D-MU Net weight: 210 g approx. (1 cable)
Length: 10 m 32.808 ft
SFB-CCJ10D-MU Net weight: 680 g approx. (1 cable)
Length: 0.1 m 0.328 ft
SFB-CSL01
Net weight: 45 g approx. (2 cables)
Length: 0.5 m 1.640 ft
SFB-CSL05
Net weight: 95 g approx. (2 cables)
Length: 1 m 3.281 ft
SFB-CSL1
Net weight: 150 g approx. (2 cables)
Length: 5 m 16.404 ft
SFB-CSL5
Net weight: 630 g approx. (2 cables)
Length: 0.5 m 1.640 ft
SFB-CB05-EX
Net weight: 95 g approx. (2 cables)
Length: 5 m 16.404 ft
SFB-CB5-EX
Net weight: 620 g approx. (2 cables)
Length: 10 m 32.808 ft
SFB-CB10-EX
Net weight: 1,200 g approx. (2 cables)
For SF4-AH□
(PNP type)
Used for connecting to the safety light curtain and to other
cables or the SF-C13 control unit.
2 cables/set for emitter and receiver
LASER
SENSORS
Used for connecting to an extension cable or the SF-C13
control unit.
2 cables/set for emitter and receiver
Connector outer diameter: ø16 mm ø0.630 in max.
Used for connecting to an extension cable or the SF-C12
control unit.
One each for emitter and receiver
Connector outer diameter: ø16 mm ø0.630 in max.
Connector color: Gray (for emitter), Black (for receiver)
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Used to connect safety light curtains in series
2 cables/set for emitter and receiver (common for emitter and
receiver)
Cable color: Gray (common for emitter and receiver)
Safety
Control Units
Safety
Components
SF4D
Used for connecting to the safety light curtain and to
SF-C14EX control unit or 8-core extension cable with
connectors on both ends
2 cables/set for emitter and receiver
Connector outer diameter: ø14 mm ø0.551 in max.
8-core bottom cap cables. The connector cables (on control
circuit side) used with previous safety light curtains can be
connected without any modification, thus enabling easy
replacement of the existing devices with the SF4B / SF4B-G
Length: 0.5 m 1.640 ft
series products.
Net weight:
Also, SFB-CB05-A-P and SFB-CB05-A-N are usable even
110 g approx. (2 cables)
when external device input is not used as the polarity of PNP
output or NPN output is fixed.
2 cables/set for emitter and receiver
Connector outer diameter: ø14 mm ø0.551 in max.
Note: Where the cable color has not been specified, it is black for emitter, gray with black line for outer diameter is ø6 mm ø0.236 in, min. bending radius is R6
mm R0.236 in.
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
513
Designation
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Intermediate supporting bracket
Spare parts (Accessories for safety light curtain)
PHOTOELECTRIC
SENSORS
SIMPLE
WIRE-SAVING
UNITS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
ORDER GUIDE
FIBER
SENSORS
LASER
SENSORS
Safety Light Curtain Type 4
Model No.
Description
Safety light
curtain
Intermediate
supporting
bracket
(Excluding
SF4B-□G□)
(Note 1)
MS-SFB-2
Intermediate
supporting
bracket (Note 2)
(For
SF4B-□G□)
MS-SF4BG-2
This bracket holds the safety light curtain at the middle. (2 pcs.
/set for emitter and receiver) Mounting is possible behind or at
the side of the safety light curtain.
Test rod ø14
SF4B-TR14
Min. sensing object for regular checking (ø14 mm ø0.551 in), with
finger protection type (min. sensing object ø14 mm ø0.551 in)
SF4B-TR25
Min. sensing object for regular checking (ø25 mm ø0.984 in), with
hand protection type (min. sensing object ø25 mm ø0.984 in)
Test rod ø25
This bracket holds the safety light curtain at the middle. (2 pcs.
/set for emitter and receiver) Mounting is possible behind or at
the side of the safety light curtain.
M5 hexagonsocket-head bolt
Purchase
separately.
Intermediate supporting
bracket
MS-SFB-2
Sensing surface
Notes: 1) The number of sets required varies depending on the product.
1 set: SF4B-F□.............................. 79 to 111 beam channels
SF4B-H□.............................. 40 to 56 beam channels
SF4B-A□.............................. 20 to 28 beam channels
2 sets: SF4B-F127□
SF4B-H□.............................. 64 to 80 beam channels
SF4B-A□.............................. 32 to 40 beam channels
3 sets: SF4B-H□.............................. 88 to 96 beam channels
SF4B-A□.............................. 44 to 48 beam channels
• MS-SFB-2
2) The number of sets required varies depending on the product.
1 set: SF4B-F□G□......................... 79 to 127 beam channels
SF4B-H□G□......................... 40 to 64 beam channels
SF4B-A□G□......................... 20 to 32 beam channels
2 set: SF4B-H□G□......................... 72 to 96 beam channels
SF4B-A□G□......................... 36 to 48 beam channels
M5 hexagonsocket-head bolt
Purchase
separately.
Safety light curtain
Intermediate supporting
bracket
MS-SFB-2
Sensing surface
• MS-SF4BG-2
M5 hexagon-socket
-head bolt
Purchase
separately.
(
)
M5 hexagon-socket
-head bolt
Purchase
separately.
(
)
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
OPTIONS
FIBER
SENSORS
Control units
Designation
514
LASER
SENSORS
Appearance
Connector
connection type
control unit
Robust type
control unit
Slim type
control unit
Application
expansion unit for
SF4B / SF4B-G series
Handy-controller
non-compatible
type
Model No.
SF-C11
Application cable
PHOTOELECTRIC
SENSORS
Description
Use 8-core cable with connector to connect to the safety
light curtain.
Compatible with up to Control Category 4.
Extension cable: SFB-CCJ10□ Interference prevention wires and muting function cannot
be used.
Bottom cap cable: SFB-CB□
SF-C12
Use 12-core cable with connector to connect to the safety
Bottom cap cable:
light curtain.
SFB-CB05-MU
Compatible with up to Control Category 4.
Extension cable:
Muting function cannot be used.
SFB-CCJ10□-MU
Interference prevention wires can be used.
SF-C13
Use a discrete wire cable to connect to the safety light
Bottom cap cable:
curtain.
SFB-CCB□(-MU)
Compatible with up to Control Category 4.
Extension cable:
Interference prevention wires and muting function can be
SFB-CC□(-MU)
used.
SF-C14EX
SF-C14EX-01
The muting control function and emergency stop input
Bottom cap cable:
expand the applications of the safety light curtains.
SFB-CB□-EX Use exclusive cable to connect to the safety light curtain.
Compatible with up to Control Category 4.
Extension cable: SFB-CCJ10□ The handy-controller SFB-HC (optional) cannot be used
with SF‑C14EX‑01.
Note: Refer to SF-C10 series pages (p.663~) for the control units.
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
SF-C12 spare relay set
LASER
MARKERS
A set of spare relays (2 safety relays and 1 removal tool) is available for the safety relay that is built into the SF-C12.
Model No.: SF-C12-RY
PLC
• Recommended safety relay
Panasonic Corporation
SF relay, slim type
SF relay, slim type
SFS3-L-DC24V (AG1S132)
SFS4-L-DC24V (AG1S142)
DIN terminal block
SFS4-SFD (AG1S847) [4-poles type]
SFS6-SFD (AG1S867) [6-poles type]
Note: Contact Panasonic Corporation for details on the recommended
products.
Item
Type
Model No.
Part No.
Contact arrangement
Rated nominal
switching capacity
Min. switching capacity
Coil rating
Rated power
consumption
Operation time
Release time
Ambient temperature
Applicable standards
With LED indicator
SFS3-L-DC24V
SFS4-L-DC24V
AG1S132
AG1S142
3a1b
4a2b
6 A / 250 V AC, 6 A / 30 V DC
1 mA / 5 V DC
15 mA / 24 V DC
20.8 mA / 24 V DC
360 mW
500 mW
20 ms or less
20 ms or less
–40 to +85 °C –40 to +185 °F (Humidity: 5 to 85 % RH)
UL/c-UL, TÜV, Korea’s S-mark
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety control unit
Safety
Control Units
Creating safety circuits is easier than ever.
Safety
Components
SF-C21
SF4D
P.647~
Safety control unit
SF-C21
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
515
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
OPTIONS
Pigtailed type
Handy-controller
Designation
Appearance
Model No.
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
In
case
ofcable
8-core
Bottom
cap
SFB-HC
Co
de
Mo
nit
Pr or
ote
Co ct
FU
py
NC
TIO
N
CA
NC
(Note)
EL
EN
8-core
12-core → 8-core
InBottom
case cap
of 12-core
Adapter cable
R
Bottom cap
cable
* Includes 2 adapter cables
Cable set for
cable type
connection
SFC-WNC1
(Note)
Adapter cable
(Accessory)
Cable set
Synchronization Cable set
Synchronization +
Synchronization -
+V 0V
UV
CURING
SYSTEMS
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
Extension cable
Adapter→cable
12-core
8-core
(Accessory)
Adapter cable
(Accessory)
Not used
8-core
ControlControl
circuit circuit
8-core
FUNCTION
8-core
ENTER
FUNCTION
Handy-controller
CANCEL
ENTER
Handy-controller
Terminal
block
Safety light curtain diagnosis software
8-core
Not used
CANCEL
Terminal
block
Simply input the error number of the safety light curtain on the screen, and the section of
maintenance needed will be located and coping process will be displayed.
* Can be downloaded free from our website.
Safety light curtain diagnosis software
Y-shaped connector
Type
Appearance
Model No.
Wire-saving
Y-shaped
connector
SFB-WY1
(Note)
Selection
Guide
Safety Light
Curtains
Adapter cable
(Accessory)
Synchronization +
ENERGY
MANAGEMENT
SOLUTIONS
MACHINE
VISION
SYSTEMS
Handy-controller
12-core → 8-core
Cable type
HUMAN
MACHINE
INTERFACES
FA
COMPONENTS
Extension cable
ENTER
Cable type
+V 0V
Note: A
handy-controller cannot be used with the SF4B-□-01 (p.509~),
the SF4B-□-03 (p.509) and the SF-C14EX-01 (p.514).
8-core8-core → 12-core
ENTER
FUNCTION
CANCEL
MEASUREMENT
SENSORS
PLC
FUNCTION
CANCEL
Extension cable
Adapter cable
12-core
→ 8-core
8-core
→ 12-core
(Accessory)
(Accessory)
Handy-controller
cable
TE
WIRE-SAVING
SYSTEMS
LASER
MARKERS
8-core
In case of 12-core
Fix
ed
Floa bla
ting nki
Aux blan ng
Lig iliary king
ht out
con
em put
trol issi
on
Handycontroller
8-core
SIMPLE
WIRE-SAVING
UNITS
STATIC
CONTROL
DEVICES
Extension cable
Bottom cap cable
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
In case of 8-core
Pigtailed type
Wire-saving connector for standard components (8-core cable). Cables of emitter
and receiver are consolidated into one cable for wire-saving.
Wiring has +24 V, 0 V, OSSD 1, OSSD 2, output polarity setting wire (shield).
Net weight: 35 g approx.
Power wire and synchronization wire are connected inside the connector.
Interlock is disabled (automatic reset).
WY1-CCN3
Cable length: 3 m 9.843 ft
Net weight: 200 g approx.
(1 cable)
WY1-CCN10
Cable length: 10 m 32.808 ft
Net weight: 620 g approx.
(1 cable)
(Note)
Cable with
connector
on one side
Description
(Note)
Mating cable for Y-shaped connector
Cable color: Gray (with black line)
Connector color: Black
The min. bending radius: R6 mm R0.236 in
Note: Not available for SF4B-□-01.
By using the Y-shaped connector, the least required wires such as power or safety output are consolidated into one cable. Man-hours taken
for wiring is eliminated to the minimum. Construction times as well as wiring mistakes are greatly reduced.
Previous
A total of 16 wires
Y-shaped connector
SF4B series
SF4B series
Only 5 wires
Less wiring mistakes! Reduced wiring time!
Easy wiring to safety PLC, etc.
SF2B
SF2C
Definition of
Sensing Heights
Y-shaped connector
8 wires
5 wires
8 wires
Control unit SF-C13
Refer to the instruction manual for more details such as installation of Y-shaped connector, terminal wiring, and wiring example.
Control unit SF-C13
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
516
OPTIONS
FIBER
SENSORS
Front protection cover (excluding SF4B-□G□) / Protection bar set (excluding SF4B-□G□) / Corner mirror
Designation
Applicable
beam axes
Finger
Hand
Front protection
cover
Protection bar set
Rear/side
protection bar set
Arm / Foot
Model No.
Model No.
Model No.
Model No.
FC-SFBH-12
FC-SFBH-16
FC-SFBH-20
FC-SFBH-24
FC-SFBH-28
FC-SFBH-32
FC-SFBH-36
FC-SFBH-40
FC-SFBH-48
FC-SFBH-56
FC-SFBH-64
FC-SFBH-72
FC-SFBH-80
FC-SFBH-88
FC-SFBH-96
MC-SFBH-12
MC-SFBH-16
MC-SFBH-20
MC-SFBH-24
MC-SFBH-28
MC-SFBH-32
MC-SFBH-36
MC-SFBH-40
MC-SFBH-48
MC-SFBH-56
MC-SFBH-64
MC-SFBH-72
MC-SFBH-80
MC-SFBH-88
MC-SFBH-96
MC-SFBH-12-T
MC-SFBH-16-T
MC-SFBH-20-T
MC-SFBH-24-T
MC-SFBH-28-T
MC-SFBH-32-T
MC-SFBH-36-T
MC-SFBH-40-T
MC-SFBH-48-T
MC-SFBH-56-T
MC-SFBH-64-T
MC-SFBH-72-T
MC-SFBH-80-T
MC-SFBH-88-T
MC-SFBH-96-T
RF-SFBH-12
RF-SFBH-16
RF-SFBH-20
RF-SFBH-24
RF-SFBH-28
RF-SFBH-32
RF-SFBH-36
RF-SFBH-40
RF-SFBH-48
RF-SFBH-56
RF-SFBH-64
RF-SFBH-72
RF-SFBH-80
RF-SFBH-88
RF-SFBH-96
23
12
6
31
16
8
39
20
10
47
24
12
55
28
14
63
32
16
71
36
18
79
40
20
95
48
24
111
56
28
127
64
32
–
72
36
–
80
40
–
88
44
–
96
48
PHOTOELECTRIC
SENSORS
Corner mirror
Effective reflective surface
236 × 72 mm 9.291 × 2.835 in
316 × 72 mm 12.441 × 2.835 in
396 × 72 mm 15.591 × 2.835 in
476 × 72 mm 18.740 × 2.835 in
556 × 72 mm 21.890 × 2.835 in
636 × 72 mm 25.039 × 2.835 in
716 × 72 mm 28.189 × 2.835 in
796 × 72 mm 31.339 × 2.835 in
956 × 72 mm 37.638 × 2.835 in
1,116 × 72 mm 43.937 × 2.835 in
1,276 × 72 mm 50.236 × 2.835 in
1,436 × 72 mm 56.535 × 2.835 in
1,596 × 72 mm 62.835 × 2.835 in
1,756 × 72 mm 69.134 × 2.835 in
1,916 × 72 mm 75.433 × 2.835 in
Note: T
he model Nos. given above denote a single unit. 2 units are required for use in mounting to the emitter/receiver (excluding corner mirror).
Front protection cover
Front protection
cover
• FC-SFBH-□
Protects sensing surface of the safety
light curtain from flying objects such as
welding spatter.
The operating range reduces when the
front protection cover is used.
Protection bar set
Rear/side protection bar set
• MC-SFBH-□
Note 1: Not available for
SF4B-□G□. M5 hexagon-
• MC-SFBH-□-T
Note 1: Not available for SF4B-□G□.
socket-head bolt
with washers
LASER
SENSORS
M5 hexagonsocket-head bolt
Note: Not available for SF4B-□G□.
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
Material: Polycarbonate
Protection bar
mounting
bracket
ENERGY
MANAGEMENT
SOLUTIONS
M5 hexagonsocket-head bolt
Operating range
FA
COMPONENTS
Safety light curtain
SF4B-H□
MACHINE
VISION
SYSTEMS
SF4B-A□
SF4B-F□ 12 to 64 beam 72 to 96 beam 6 to 32 beam 36 to 48 beam
axes type axes type axes type axes type
0.3 to 6 m 0.3 to 7.5 m 0.3 to 6 m 0.3 to 7.5 m 0.3 to 6 m
Only emitter installed 0.984 to 19.685 ft 0.984 to 24.606 ft 0.984 to 19.685 ft 0.984 to 24.606 ft 0.984 to 19.685 ft
0.3 to 6 m 0.3 to 7.5 m 0.3 to 6 m 0.3 to 7.5 m 0.3 to 6 m
Only receiver installed 0.984 to 19.685 ft 0.984 to 24.606 ft 0.984 to 19.685 ft 0.984 to 24.606 ft 0.984 to 19.685 ft
Both emitter and 0.3 to 5.5 m 0.3 to 7 m 0.3 to 5.5 m 0.3 to 7 m 0.3 to 5.5 m
receiver installed 0.984 to 18.045 ft 0.984 to 22.966 ft 0.984 to 18.045 ft 0.984 to 22.966 ft 0.984 to 18.045 ft
Note: The operating range is the possible setting distance between the emitter and the
receiver.
Protection bar
intermediate
supporting bracket
MS-SFB-6 (Optional)
(Note 3)
Protection
bar
M5 hexagonsocket-head bolt
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
Corner mirror
M5 hexagonsocket-head bolt
• RF-SFBH-□
SF4D
• Parts List
Normally for L-shaped or U-shaped installation, 2 or 3
sets of safety light curtains are needed. With the use
of a corner mirror reflecting the light, one set of safety
light curtain is possible for L-shaped or U-shaped
installation.
Designation
Protection bar
MC-SFBH-□
Number
Remarks
MC-SFBH-□-T
Number
Remarks
1 pc. Material: Aluminum 1 pc. Material: Aluminum
Material: Cold rolled
1 pc. each
Protection bar mounting bracket 1 pc. Material:
carbon steel (SPCC)
(For left side, for right side) each Die-cast zinc alloy (Note 2)
(Trivalent chrome plated)
Operating range
Hexagon-socket-head
M5
M5
2 pcs.
2 pcs.
(length: 20 mm 0.787 in)
(length: 20 mm 0.787 in)
bolt with washers
Hexagon-socket-head bolt 2 pcs.
Corner mirror
RF-SFBH-□
With 1 corner
mirror
Declined to
90 %
With 2 corner
mirror
Declined to
80 %
M5
M5
2 pcs.
(length: 16 mm 0.630 in)
(length: 18 mm 0.709 in)
Notes: 2) A
vailable as a spare part. Model No.: MS-MCSFB-1-T
3) The protection bar intermediate supporting bracket MS-SFB-6 (optional) is
installed to protection bars that are longer than the MC-SFBH-48(-T). Use if there
is much flexure bending in the protection bar. Please contact our office for details.
• Protection bar intermediate supporting bracket MS-SFB-6 (Optional)
Material: Cold rolled carbon steel (SPCC) (Trivalent chrome plated)
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
517
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
OPTIONS
Designation
Applicable
beam axes
Hand
Arm / foot
Model No.
23
12
6
31
16
8
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
39
20
10
47
24
12
PRESSURE /
FLOW
SENSORS
55
28
14
63
32
16
INDUCTIVE
PROXIMITY
SENSORS
71
36
18
79
40
20
FC-SF4BG-H12
FC-SF4BG-H16
FC-SF4BG-H20
FC-SF4BG-H24
FC-SF4BG-H28
FC-SF4BG-H32
FC-SF4BG-H36
FC-SF4BG-H40
FC-SF4BG-H48
FC-SF4BG-H56
FC-SF4BG-H64
FC-SF4BG-H72
FC-SF4BG-H80
FC-SF4BG-H88
FC-SF4BG-H96
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
95
48
24
111
56
28
127
64
32
–
72
36
–
80
40
–
88
44
–
96
48
Note: The model Nos. given above denote a single unit,
not a pair of units. 2 units are required for use in
mounting to the emitter/receiver.
Selection
Guide
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Bottom stopper
Accessory for a
front protection cover
Bottom cap cable
Material: Front protection cover ... Polycarbonate
Top / Side / Bottom stopper ... Stainless steel (SUS304)
Operating range
SF4B-H□G□
SF4B-A□G
SF4B-F□G 12 to 64 beam 72 to 96 beam 6 to 32 beam 36 to 48 beam
axes type
axes type
axes type
axes type
Only emitter installed
Only receiver installed
0.3 to 6 m
0.3 to 7.5 m
0.3 to 6 m
0.3 to 7.5 m
0.3 to 6 m
0.984 to 19.685 ft 0.984 to 24.606 ft 0.984 to 19.685 ft 0.984 to 24.606 ft 0.984 to 19.685 ft
0.3 to 5.5 m
Both emitter and
0.3 to 7 m
0.3 to 5.5 m
0.3 to 7 m
0.3 to 5.5 m
receiver installed 0.984 to 18.045 ft 0.984 to 22.966 ft 0.984 to 18.045 ft 0.984 to 22.966 ft 0.984 to 18.045 ft
Note: The operating range is the possible setting distance between the emitter and the receiver.
Others
Designation
Model No.
Description
Test rod ø45
SF4B-TR45
Min. sensing object for regular checking (ø45 mm ø1.772 in),
with arm / foot protection type (min. sensing object ø45 mm ø1.772 in)
Laser alignment tool
(Excluding SF4B-□G□)
SF-LAT-2N
Allows easy beam axis alignment using easy-to-see laser beam
Laser alignment tool
(For SF4B-□G□)
SF-LAT-4BG Allows easy beam axis alignment using easy-to-see laser beam
Caution tape
SF-TP-BG10
Laser alignment tool
(Excluding SF4B-□G□)
• SF-LAT-2N
Safety Light
Curtains
Top stopper
(Accessory for a front protection cover)
Front protection cover
Front protection
cover
Finger
AREA
SENSORS
Side stopper
(Accessory for a front protection cover)
Front protection cover (For SF4B-□G□)
Attached to the side of the safety light curtain to alert workers to
hazards (10 m 32.8 ft long)
Laser alignment tool
(For SF4B-□G□)
・SF-LAT-4BG
Caution tape
・SF-TP-BG10
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
OPTIONS
Designation
FIBER
SENSORS
Model No.
Large display unit for safety light
curtain
Description
With the auxiliary output of the safety light curtain, the operation is
easily observable from various directions.
• SF-IND-2
Specifications
• Supply voltage: 24 V DC ±15 %
• Current consumption: 12 mA or less
• Indicators: Orange LED (8 pcs. used)
[Light up when external contact is ON]
• Ambient temperature: –10 to +55 °C +14 to +131 °F
(No dew condensation or icing allowed)
• Material: POM (Enclosure)
Polycarbonate (Cover)
Cold rolled carbon steel (SPCC) (Bracket)
• Cable: 0.3 mm2 2-core cabtyre cable, 3 m 9.843 ft long
• Weight: 70 g approx. (including bracket)
Large display
unit for
safety light
curtain
I/O circuit diagrams
With NPN output type
SF-IND-2
Color code
(Brown) +V
+ 24 V DC
– ±15 %
Internal circuit
M5 hexagon-sockethead bolt
(length: 10 mm
0.394 in or more)
Purchase
separately.
*1
Attaches to top of safety light curtain.
Tighten together the mounting bracket
provided with the safety light curtain
MS-SFB-1/4, MS-SFBG-1 and the attached
mounting bracket of SF-IND-2.
AREA
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
Non-voltage contact or
NPN open-collector transistor
SIMPLE
WIRE-SAVING
UNITS
or
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
*1
Non-voltage contact or
PNP open-collector transistor
LASER
MARKERS
or
PLC
(Blue) – V
HUMAN
MACHINE
INTERFACES
Users’ circuit
Introduction to Panasonic Industrial Devices SUNX sensors that can be used as muting sensors
CX-400 SERIES Ver.2
MICRO
PHOTOELECTRIC
SENSORS
SENSOR
OPTIONS
*1
+ 24 V DC
– ±15 %
Internal circuit
PHOTOELECTRIC
SENSORS
PRESSURE /
FLOW
SENSORS
(Blue) – V
*1
Users’ circuit
Color code
(Brown) +V
LASER
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
With PNP output type
Compact Photoelectric Sensor
518
Ultra-slim Photoelectric Sensor
EX-10 SERIES Ver.2
U-shaped Micro Photoelectric Sensor
PM-25/45/65 SERIES
Rectangular-shaped Inductive Proximity Sensor
GX-F/H SERIES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
• World standard size
• Wide variation
• 3.5 mm 0.138 in thickness
• Long sensing range: 1 m 3.281 ft
(thru-beam type: EX-19)
* The EX-20 series that is
compatible with M3 mounting
screws is also available.
P.245~
P.279~
• Three protection circuits
standard on all models
• Ample beam emitting /
receiving distance of 6 mm
0.236 in
• Easy to mount with M3 screws
P.395~
• Industry longest in stable
sensing range
• 10 times the durability
(Compared to previous models)
• IP68G rating
P.785~
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
519
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
Safety Light Curtain Type 4
SPECIFICATIONS
Safety light curtain individual specifications
SF4B-F□(G)
Type
Min. sensing object ø14 mm ø0.551 in type (10 mm 0.394 in beam pitch)
Model No. SF4B-F23□ SF4B-F23G SF4B-F31□ SF4B-F31G SF4B-F39□ SF4B-F39G SF4B-F47□ SF4B-F47G SF4B-F55□ SF4B-F55G
Item
Number of beam channels
Protective height (Note 2)
China Press compliant
(GB/T 4584)
23
244 mm
9.606 in
220 mm
8.661 in
2.4 × 10
Type
510 g
approx.
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
380 mm
14.960 in
2.8 × 10
–9
470 mm
18.504 in
55
484 mm
19.055 in
460 mm
18.110 in
550 mm
21.654 in
564 mm
22.205 in
540 mm
21.260 in
Emitter: 100 mA or less, Receiver: 160 mA or less
3.2 × 10
–9
3.6 × 10–9
4.0 × 10–9
660 g
approx.
1,340 g
approx.
810 g
approx.
1,700 g
approx.
960 g
approx.
2,000 g
approx.
1,110 g
approx.
2,400 g
approx.
Min. sensing object ø14 mm ø0.551 in type (10 mm 0.394 in beam pitch)
Protective height (Note 2)
China Press compliant
(GB/T 4584)
Current consumption
63
630 mm
24.803 in
71
644 mm
25.354 in
620 mm
24.409 in
710 mm
27.953 in
79
724 mm
28.504 in
700 mm
27.559 in
790 mm
31.102 in
95
804 mm
31.654 in
780 mm
30.708 in
950 mm
37.402 in
964 mm
37.953 in
940 mm
37.007 in
Emitter: 100 mA or less, Receiver: 160 mA or less Emitter: 115 mA or less, Receiver: 190 mA or less
4.4 × 10–9
PFHD
4.8 × 10–9
MTTFD
5.2 × 10–9
6.0 × 10–9
100 years or more
Net weight
(Total of emitter and receiver)
1,260 g
approx.
2,800 g
approx.
1,420 g
approx.
3,200 g
approx.
1,570 g
approx.
3,400 g
approx.
1,870 g
approx.
4,200 g
approx.
Type Min. sensing object ø14 mm ø0.551 in type (10 mm 0.394 in beam pitch)
Model No. SF4B-F111□ SF4B-F111G SF4B-F127□ SF4B-F127G
Item
China Press compliant
(GB/T 4584)
111
1,110 mm
43.701 in
Net weight
(Total of emitter and receiver)
127
1,124 mm
44.252 in
1,100 mm
43.306 in
1,270 mm
50.000 in
1,284 mm
50.551 in
1,260 mm
49.606 in
Emitter: 135 mA or less, Receiver: 230 mA or less
6.8 × 10–9
MTTFD
SF4B/
SF4B-G
–9
980 g
approx.
Number of beam channels
PFHD
SF4D
47
404 mm
15.906 in
Model No. SF4B-F63□ SF4B-F63G SF4B-F71□ SF4B-F71G SF4B-F79□ SF4B-F79G SF4B-F95□ SF4B-F95G
Item
Current consumption
Safety
Components
300 mm
11.811 in
390 mm
15.354 in
100 years or more
Protective height (Note 2)
Safety
Control Units
39
324 mm
12.756 in
MTTFD
Net weight
(Total of emitter and receiver)
MACHINE
VISION
SYSTEMS
Safety Light
Curtains
310 mm
12.205 in
Emitter: 80 mA or less, Receiver: 120 mA or less
PFHD
Number of beam channels
Selection
Guide
31
230 mm
9.055 in
Current consumption
FA
COMPONENTS
UV
CURING
SYSTEMS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
7.6 × 10–9
100 years or more
2,170 g
approx.
5,000 g
approx.
2,470 g
approx.
5,600 g
approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. The model No.
with “G“ is a robust type.
PFHD: Probability of dangerous failure per hour, MTTFD: Mean time to dangerous failure (in years)
2) In the case of “When used as safety device for presses in China”, the distance between the center of the first beam axis and the center of the last beam
axis of the device becomes the protective height. For details, refer to “Definition of sensing heights” (p.645).
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
SPECIFICATIONS
FIBER
SENSORS
LASER
SENSORS
SF4B-H□(G□)
Type
Min. sensing object ø25 mm ø0.984 in type (20 mm 0.787 in beam pitch)
Model No. SF4B-H12□ SF4B-H12G□ SF4B-H16□ SF4B-H16G□ SF4B-H20□ SF4B-H20G□ SF4B-H24□ SF4B-H24G□ SF4B-H28□ SF4B-H28G□
Item
Number of beam channels
Protective height (Note 2)
China Press compliant
(GB/T 4584)
12
230 mm
9.055 in
16
244 mm
9.606 in
220 mm
8.661 in
Current consumption
310 mm
12.205 in
20
324 mm
12.756 in
300 mm
11.811 in
390 mm
15.354 in
24
404 mm
15.906 in
380 mm
14.960 in
Emitter: 70 mA or less, Receiver: 95 mA or less
1.8 × 10
PFHD
2.0 × 10
–9
–9
MTTFD
470 mm
18.504 in
28
484 mm
19.055 in
550 mm
21.654 in
460 mm
18.110 in
564 mm
22.205 in
540 mm
21.260 in
Emitter: 80 mA or less, Receiver: 115 mA or less
2.2 × 10
–9
2.4 × 10
2.6 × 10
–9
–9
100 years or more
Net weight
(Total of emitter and receiver)
510 g
approx.
980 g
approx.
Type
660 g
approx.
1,340 g
approx.
810 g
approx.
1,700 g
approx.
960 g
approx.
2,000 g
approx.
1,110 g
approx.
2,400 g
approx.
Min. sensing object ø25 mm ø0.984 in type (20 mm 0.787 in beam pitch)
Model No. SF4B-H32□ SF4B-H32G□ SF4B-H36□ SF4B-H36G□ SF4B-H40□ SF4B-H40G□ SF4B-H48□ SF4B-H48G□ SF4B-H56□ SF4B-H56G□
Item
Number of beam channels
Protective height (Note 2)
China Press compliant
(GB/T 4584)
Current consumption
32
630 mm
24.803 in
36
644 mm
25.354 in
620 mm
24.409 in
710 mm
27.953 in
40
724 mm
28.504 in
700 mm
27.559 in
Emitter: 80 mA or less, Receiver: 115 mA or less
PFHD
2.8 × 10–9
3.0 × 10–9
MTTFD
790 mm
31.102 in
48
804 mm
31.654 in
780 mm
30.708 in
950 mm
37.402 in
56
964 mm
37.953 in
1,124 mm
44.252 in
1,260 g
approx.
2,800 g
approx.
Type
1,420 g
approx.
3,200 g
approx.
1,570 g
approx.
3,400 g
approx.
4,200 g
approx.
Protective height (Note 2)
China Press compliant
(GB/T 4584)
Current consumption
PFHD
64
72
1,284 mm
50.551 in
1,260 mm
49.606 in
1,430 mm
56.299 in
80
1,444 mm
56.850 in
1,420 mm
55.905 in
1,580 mm
62.205 in
1,750 mm
68.898 in
2,170 g
approx.
5,000 g
approx.
96
1,764 mm
69.449 in
1,740 mm
68.503 in
4.4 × 10–9
4.8 × 10–9
5.2 × 10–9
5.6 × 10–9
1,910 mm
75.197 in
1,924 mm
75.748 in
1,900 mm
74.803 in
5,600 g
approx.
2,770 g
approx.
6,400 g
approx.
3,070 g
approx.
7,000 g
approx.
3,370 g
approx.
7,800 g
approx.
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
6.0 × 10–9
100 years or more
2,470 g
approx.
INDUCTIVE
PROXIMITY
SENSORS
LASER
MARKERS
88
1,604 mm
63.150 in
PRESSURE /
FLOW
SENSORS
4.0 × 10–9
Emitter: 100 mA or less,
Emitter: 110 mA or less, Receiver: 180 mA or less Emitter: 120 mA or less, Receiver: 200 mA or less
Receiver: 160 mA or less
MTTFD
Net weight
(Total of emitter and receiver)
1,590 mm
62.598 in
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
STATIC
CONTROL
DEVICES
Min. sensing object ø25 mm ø0.984 in type (20 mm 0.787 in beam pitch)
1,270 mm
50.000 in
AREA
SENSORS
Emitter: 100 mA or less,
Receiver: 160 mA or less
Model No. SF4B-H64□ SF4B-H64G SF4B-H72□ SF4B-H72G SF4B-H80□ SF4B-H80G SF4B-H88□ SF4B-H88G SF4B-H96□ SF4B-H96G□
Number of beam channels
MICRO
PHOTOELECTRIC
SENSORS
MEASUREMENT
SENSORS
3.6 × 10–9
1,870 g
approx.
PHOTOELECTRIC
SENSORS
1,100 mm
43.306 in
940 mm
37.007 in
Emitter: 90 mA or less, Receiver: 140 mA or less
3.2 × 10–9
1,110 mm
43.701 in
100 years or more
Net weight
(Total of emitter and receiver)
Item
520
3,670 g
approx.
8,400 g
approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. The model No.
with “G“ is a robust type.
PFHD: Probability of dangerous failure per hour, MTTFD: Mean time to dangerous failure (in years)
2) In the case of “When used as safety device for presses in China”, the distance between the center of the first beam axis and the center of the last beam
axis of the device becomes the protective height. For details, refer to “Definition of sensing heights” (p.645).
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
521
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
Safety Light Curtain Type 4
SPECIFICATIONS
SF4B-A□(G)
Type
Protective height (Note 2)
China Press compliant
(GB/T 4584)
Item
China Press compliant
(GB/T 4584)
440 mm
17.323 in
564 mm
22.205 in
520 mm
20.472 in
1.8 × 10–9
–9
1.9 × 10–9
660 g
approx.
1,340 g
approx.
810 g
approx.
1,700 g
approx.
960 g
approx.
2,000 g
approx.
1,110 g
approx.
2,400 g
approx.
Min. sensing object ø45 mm ø1.772 in type (40 mm 1.575 in beam pitch)
16
630 mm
24.803 in
18
644 mm
25.354 in
710 mm
27.953 in
600 mm
23.622 in
20
724 mm
28.504 in
680 mm
26.772 in
790 mm
31.102 in
24
804 mm
31.654 in
950 mm
37.402 in
760 mm
29.921 in
2.1 × 10–9
28
964 mm
37.953 in
1,110 mm
43.701 in
920 mm
36.220 in
1,080 mm
42.520 in
Emitter: 75 mA or less, Receiver: 105 mA or less
2.2 × 10–9
1,124 mm
44.252 in
Emitter: 80 mA or less,
Receiver: 120 mA or less
2.4 × 10–9
2.6 × 10–9
1,260 g
approx.
2,800 g
approx.
1,420 g
approx.
3,200 g
approx.
1,570 g
approx.
3,400 g
approx.
1,870 g
approx.
4,200 g
approx.
2,170 g
approx.
5,000 g
approx.
Min. sensing object ø45 mm ø1.772 in type (40 mm 1.575 in beam pitch)
Model No. SF4B-A32□ SF4B-A32G SF4B-A36□ SF4B-A36G SF4B-A40□ SF4B-A40G SF4B-A44□ SF4B-A44G SF4B-A48□ SF4B-A48G
Item
32
Number of beam channels
Protective height (Note 2)
China Press compliant
(GB/T 4584)
1,270 mm
50.000 in
36
1,284 mm
50.551 in
1,430 mm
56.299 in
1,240 mm
48.819 in
40
1,444 mm
56.850 in
1,400 mm
55.118 in
1,590 mm
62.598 in
44
1,604 mm
63.150 in
2.8 × 10
3.0 × 10
–9
1,750 mm
68.898 in
1,560 mm
61.417 in
Emitter: 80 mA or less,
Emitter: 85 mA or less, Receiver: 130 mA or less
Receiver: 120 mA or less
3.2 × 10
–9
MTTFD
48
1,764 mm
69.449 in
1,910 mm
75.197 in
1,720 mm
67.716 in
1,924 mm
75.748 in
1,880 mm
74.016 in
Emitter: 95 mA or less, Receiver: 140 mA or less
3.4 × 10–9
–9
3.6 × 10–9
100 years or more
Net weight
(Total of emitter and receiver)
2,470 g
approx.
5,600 g
approx.
2,770 g
approx.
6,400 g
approx.
3,070 g
approx.
7,000 g
approx.
3,370 g
approx.
7,800 g
approx.
3,670 g
approx.
8,400 g
approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. The model No.
with “G“ is a robust type.
PFHD: Probability of dangerous failure per hour, MTTFD: Mean time to dangerous failure (in years)
2) In the case of “When used as safety device for presses in China”, the distance between the center of the first beam axis and the center of the last beam
axis of the device becomes the protective height. For details, refer to “Definition of sensing heights” (p.645).
Safety light curtain common specifications
Type Min. sensing object ø14 mm ø0.551 in type Min. sensing object ø25 mm ø0.984 in type Min. sensing object ø45 mm ø1.772 in type
Model No.
SF4B-F□(G)
SF4B-H□(G□)
SF4B-A□(G)
SFB-HC non-compatible
SF4B-F□-01
SF4B-H□-01
SF4B-A□-01
Item Korean press compliant
SF4B-F□-03
SF4B-H□-03
Applicable standards
(Note 2)
BSF4-AH80
Definition of
Sensing Heights
980 g
approx.
Type
SF4C
SF2C
550 mm
21.654 in
100 years or more
SF4B-C
SF2B
14
484 mm
19.055 in
Emitter: 70 mA or less, Receiver: 95 mA or less
1.7 × 10
–9
MTTFD
PFHD
SF4B/
SF4B-G
510 g
approx.
2.0 × 10–9
Current consumption
SF4D
470 mm
18.504 in
360 mm
14.173 in
Emitter: 70 mA or less, Receiver: 95 mA or less
Net weight
(Total of emitter and receiver)
UV
CURING
SYSTEMS
12
404 mm
15.906 in
Model No. SF4B-A16□ SF4B-A16G SF4B-A18□ SF4B-A18G SF4B-A20□ SF4B-A20G SF4B-A24□ SF4B-A24G SF4B-A28□ SF4B-A28G
PFHD
Safety
Components
1.6 × 10
–9
Type
LASER
MARKERS
Safety
Control Units
280 mm
11.024 in
390 mm
15.354 in
100 years or more
Current consumption
Safety Light
Curtains
10
324 mm
12.756 in
MTTFD
Net weight
(Total of emitter and receiver)
STATIC
CONTROL
DEVICES
Selection
Guide
310 mm
12.205 in
200 mm
7.874 in
1.5 × 10
PFHD
MEASUREMENT
SENSORS
MACHINE
VISION
SYSTEMS
8
244 mm
9.606 in
Emitter: 65 mA or less, Receiver: 85 mA or less
Protective height (Note 2)
FA
COMPONENTS
230 mm
9.055 in
Current consumption
WIRE-SAVING
SYSTEMS
ENERGY
MANAGEMENT
SOLUTIONS
6
Number of beam channels
Number of beam channels
HUMAN
MACHINE
INTERFACES
Min. sensing object ø45 mm ø1.772 in type (40 mm 1.575 in beam pitch)
Model No. SF4B-A6□ SF4B-A6G SF4B-A8□ SF4B-A8G SF4B-A10□ SF4B-A10G SF4B-A12□ SF4B-A12G SF4B-A14□ SF4B-A14G
Item
SIMPLE
WIRE-SAVING
UNITS
PLC
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
International standard
Japan
Europe (EU)
North America
South Korea (S-Mark)
China (GB)
CE marking directive compliance
IEC 61496-1/2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)
JIS B 9704-1/2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508-1 to 7 (SIL3)
EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2
ANSI/UL 61496-1/2 (Type 4), ANSI/UL 508, UL 1998 (Class 2), CAN/CSA 61496-1/2 (Type 4), CAN/CSA C22.2 No.14,
OSHA 1910.212, OSHA 1910.217(C), ANSI B11.1 to B11.19, ANSI/RIA 15.06
S1-G-35-2005, S2-W-11-2003 (SF4B-□ only)
GB/T 4584 (excluding SF4B-□-03)
Machinery Directive, EMC Directive, RoHS Directive
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
522
SPECIFICATIONS
FIBER
SENSORS
LASER
SENSORS
Safety light curtain common specifications
Type Min. sensing object ø14 mm ø0.551 in type Min. sensing object ø25 mm ø0.984 in type Min. sensing object ø45 mm ø1.772 in type
Model No.
SF4B-F□(G)
SF4B-H□(G□)
SF4B-A□(G)
SFB-HC non-compatible
SF4B-F□-01
SF4B-H□-01
SF4B-A□-01
Item Korean press compliant
SF4B-F□-03
Operating range (Note 3)
Min. sensing object (Note 4)
Effective aperture angle
Supply voltage
Control outputs
(OSSD 1, OSSD 2)
SF4B-H□-03
0.3 to 7 m 0.984 to 22.966 ft
ø14 mm ø0.551 in opaque object
12 to 64 beam channels type: 0.3 to 9 m 0.984 to 29.528 ft 6 to 32 beam channels type: 0.3 to 9 m 0.984 to 29.528 ft
72 to 96 beam channels type: 0.3 to 7 m 0.984 to 22.966 ft 36 to 48 beam channels type: 0.3 to 7 m 0.984 to 22.966 ft
ø25 mm ø0.984 in opaque object
ø45 mm ø1.772 in opaque object
±2.5° or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2)]
24 V DC ±10 % Ripple P-P 10 % or less
PNP open-collector transistor / NPN open-collector transistor (switching method)
• When selecting PNP output: Max. source current 200 mA, When selecting NPN output: Max. sink current 200 mA
• Applied voltage: same as supply voltage When selecting PNP output: between the control output and +V,
When selecting NPN output: between the control output and 0 V
• Residual voltage: 2.5 V or less (When selecting PNP output: source current 200 mA, when selecting NPN output: sink current 200 mA)
(when using 20 m 65.617 ft length cable)
Operation mode
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any
malfunction in the safety light curtain or the synchronization signal)(Note 5,6)
Protection circuit
Incorporated
Response time
Auxiliary output
(Non-safety output)
OFF response: 14 ms or less, ON response: 80 to 90 ms
PNP open-collector transistor / NPN open-collector transistor (switching method)
• When selecting PNP output: Max. source current 60 mA, When selecting NPN output: Max. sink current 60 mA
• Applied voltage: same as supply voltage When selecting PNP output: between the auxiliary output and +V,
When selecting NPN output: between the auxiliary output and 0 V
• Residual voltage: 2.5 V or less (When selecting PNP output: source current 60 mA, when selecting NPN output: sink current 60 mA)
(when using 20 m 65.617 ft length cable)
Operation mode
OFF when control outputs are ON, ON when control outputs are OFF [Factory setting, operating mode can be changed using
the SFB-HC (optional) handy-controller].
Protection circuit
Incorporated
Responce time
OFF replay: 34 ms or less, ON replay 110 ms or less
Interference prevention function
Incorporated (Note 7) (Available only when in series connection for SF4B-□-03)
Emission halt function / Interlock function
Incorporated / Incorporated [Manual reset / Auto reset (Note 8)]
External device monitoring function
Incorporated
Override function / Muting function
Incorporated (Note 7) (excluding SF4B-□-03) / Incorporated (Note 7) (excluding SF4B-□-03)
Environmental resistance
Optional functions (Note 9)
Fixed blanking, floating blanking, auxiliary output switching, interlock setting changing, external relay monitor setting changing,
muting setting changing, protecting, light emitting amount control
Degree of protection
IP67 / IP65 (IEC)
Ambient temperature
–10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F
Ambient humidity
Ambient illuminance
Dielectric strength voltage
30 to 85 % RH, Storage: 30 to 95 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
Emitting element
Material
Connecting method / Cable length
Accessories
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
Shock resistance
PHOTOELECTRIC
SENSORS
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Enclosure: Aluminium, Upper and lower edges: Iron, Sensing surface: Polycarbonate and Polyester resin, Cap: PBT
Connector / Total length up to 50 m 164.042 ft is possible for both emitter and receiver, with optional mating cables (Note 10)
MS-SFB-2 (Intermediate supporting bracket): (Note 11) MS-SFB-2 (Intermediate supporting bracket): (Note 11) MS-SFB-2
MS-SF4BG-2 (Intermediate supporting bracket): (Note 12) MS-SF4BG-2 (Intermediate supporting bracket): (Note 12) (Intermediate supporting bracket): (Note 11)
SF4B-TR14 (Test rod): 1 No.
SF4B-TR25 (Test rod): 1 No.
MS-SF4BG-2 (Intermediate supporting bracket): (Note 12)
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
Model Nos. having the suffix “G” are robust type.
2) PLe SIL3 compliant from production in August 2009.
3) T
he operating range is the possible setting distance between the emitter and the receiver.
4) When the floating blanking function is used, the size of the min. sensing object is changed. For details, refer to “Safety distance” (p.532).
5) The outputs are not “OFF” when muting function is active even if the beam channel is interruped.
6) In case the blanking function is valid, the operation mode is changed. For details, refer to “Safety distance” (p.532).
7) In case of using this function, please use 12-core cable.
8) The manual reset and auto reset are possible to be switched depending on the wiring status.
9) In case of using optional function, the handy-controller (SFB-HC) (optional) is required. However, a handy-controller cannot be used with the
SF4B-□-01, SF4B-□-03 and the SF-C14EX-01.
10) The cable can be extended within 30 m 98.425 ft (for emitter/receiver) when two safety light curtains are connected in series, within 20 m 65.617 ft when
three safety light curtains are connected in series. Furthermore, when the muting lamp is used, the cable can be extended within 40 m 131.234 ft (for
emitter/receiver).
11) The intermediate supporting bracket (MS-SFB-2) is enclosed with the following models. The number of sets required varies depending on the product.
1 set: SF4B-F□............... 79 to 111 beam channels, SF4B-H□.....................40 to 56 beam channels,
SF4B-A□.............. 20 to 28 beam channels
2 sets: SF4B-F127, SF4B-H□ ...64 to 80 beam channels, SF4B-A□....32 to 40 beam channels
3 sets: SF4B-H□.............. 88 to 96 beam channels, SF4B-A□.......................44 to 48 beam channels
12) The intermediate supporting bracket (MS-SF4BG-2) is enclosed with the following models.
1 set: SF4B-F□G............ 79 to 127 beam channels, SF4B-H□G□................40 to 64 beam channels
SF4B-A□G............ 20 to 32 beam channels
2 sets: SF4B-H□G□......... 72 to 96 beam channels, SF4B-A□G....................36 to 48 beam channels
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
523
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
SPECIFICATIONS
Control units
Item
Connectable safety light curtains
Applicable standards
CE marking directive compliance
Control category
Supply voltage / Current consumption
Fuse (rating)
Safety output
Utilization category
Rated operation voltage (Ue) /
Rated operation current (le)
Contact resistance
Contact protection fuse rating
Pick-up delay (Auto reset/Manual reset)
Response time
Auxiliary output
Rated operation voltage/current
Contact protection fuse rating
Semiconductor auxiliary output
(AUX)
Output operation
Excess voltage category
Polarity selection function
(Note 4)
Pollution degree
Protection
Ambient temperature
Enclosure material
Weight
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
SF-C11 (Note 2)
SF-C12
Model No.
Connectable safety light curtains
Applicable standards
CE marking directive compliance
Control category
Supply voltage / Current consumption
Safety output (Safety output 1, 2, 3)
Operation mode
(Output operation)
Response time
Auxiliary outputs
[Auxiliary output 1, 2, 3, 4 (Note 5)]
Operation mode
(Output operation)
Muting lamp output
Protection
Ambient temperature
Material
Connection terminal
Weight
SF-C13 (Note 2)
SF4B / SF4B-G / SF4D / SF2B series
SF4B / SF4B-G series
Safety light curtains manufactured by Panasonic Industrial Devices SUNX
IEC 61496-1, EN 61496-1, ANSI/UL 61496-1, CAN/CSA 61496-1, JIS B 9704-1, etc.
Machinery Directive, Low Voltage (SF-C11/C13 only) Directive, EMC Directive, RoHS Directive
ISO 13849-1 (EN ISO 13849-1, JIS B 9705-1) compliance up to Category 4, PLe standards
24 V DC ±10 % Ripple P-P 10 % or less / 100 mA or less (without safety light curtain)
Built-in electronic fuse, Triggering current: 0.5 A or more, Reset after power down
NO contact × 3 (13-14, 23-24, 33-34)
NO contact × 2 (13-14, 23-24)
NO contact × 3 (13-14, 23-24, 33-34)
AC-15, DC-13 (IEC 60947-5-1)
30 V DC / 6 A, 230 V AC / 6 A, resistive load 24 V DC / 1 A, resistive load
30 V DC / 4 A, 230 V AC / 4 A, resistive load
(For inductive load, during contact protection) (For inductive load, during contact protection) (For inductive load, during contact protection)
Min. applicable load: 10 mA (at 24 V DC) (Note 3) Min. applicable load: 15 mA (at 24 V DC) Min. applicable load: 10 mA (at 24 V DC) (Note 3)
100 mΩ or less (initial value)
50 mΩ or less (initial value)
100 mΩ or less (initial value)
6 A (slow blow)
3 A (slow blow)
4 A (slow blow)
80 ms or less / 90 ms or less
30 ms or less / 30 ms or less
80 ms or less / 90 ms or less
10 ms or less
14 ms or less
10 ms or less
Safety relay contact (NC contact) ×1 (41-42) (Related to safety output) Safety relay contact (NC contact) × 1 (31-32) (Related to safety output) Safety relay contact (NC contact) × 1 (41-42) (Related to safety output)
24 V DC / 2 A, Min. applicable load: 10 mA (at 24 V DC) 30 V DC / 3 A, Min. applicable load: 15 mA (at 24 V DC) 24 V DC / 2 A, Min. applicable load: 10 mA (at 24 V DC)
2 A (slow blow)
3 A (slow blow)
2 A (slow blow)
–
PNP open‑collector transistor
PNP open-collector transistor NPN open-collector transistor
–
Related to auxiliary output of safety light curtain
ON when the safety light curtain is interrupted
II
III
II
Incorporated (Cable connection allows selection of plus/minus ground)
Incorporated (Sliding switch allows selection of plus/minus ground)
Minus ground: Correspond to PNP output safety light curtain
Minus ground: Correspond to PNP output safety light curtain
Plus ground: Correspond to NPN output safety light curtain
Plus ground: Correspond to NPN output safety light curtain
2
Enclosure: IP40, Terminal: IP20
IP65
Enclosure: IP40, Terminal: IP20
–10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F
ABS
Die-cast aluminum
ABS
Net weight: 320 g approx.
Net weight: 1 kg approx.
Net weight: 200 g approx.
Notes: 1) W
here measurement conditions have not been specified precisely, the
conditions used were an ambient temperature of +20 °C +68 °F.
2) SF-C11 and SF-C13 have acqusred the Korea S-mark.
3) If several SF-C11 or SF-C13 units are being used in a line together, leave
a space of 5 mm 0.197 in or more between each unit. If the units are
touching each other, reduce the rated operating current for safety output
in accordance with the ambient operating temperature as shown in the
graphs at right.
4) Please switch the sliding switch to the PNP side for minus ground and to
the NPN side for plus ground.
5) Refer to p.667 for details of the specifications for the control unit SF-C11/C12/C13.
Item
Selection
Guide
Model No.
Dilating when SF-C11 units
are mounted close together
6
5
4
3
2
1
0
32
Dilating when SF-C13 units
are mounted close together
Rated operation current (A)
LASER
SENSORS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Rated operation current (A)
FIBER
SENSORS
Safety Light Curtain Type 4
35 40 45 50 55
95 104 113 122 131
Ambient temperature (°C °F)
6
5
4
3
2
1
0
32
35 40 45 50 55
95 104 113 122 131
Ambient temperature (°C °F)
SF-C14EX(-01) (Note 2)
SF4B / SF4B-G series
IEC 61496-1, EN 61496-1, ANSI/UL 61496-1, CAN/CSA 61496-1, JIS B 9704-1, etc.
Machinery Directive, EMC Directive, RoHS Directive
ISO 13849-1 (EN ISO 13849-1, JIS B 9705-1) compliance up to Category 4, PLe standards
24 V DC ±10 % Ripple P-P 10 % or less / 0.2 A or less (without safety light curtain and other external connecting device)
PNP open-collector transistor 2 outputs × 3 or NPN open-collector transistor 2 outputs × 3 (selectable using a slider switch)
Safety output 1: ON when the safety light curtain is in light receiving condition, OFF when the safety light curtain is in light interrupted condition (Note 3)
Safety output 2: O
N when the safety light curtain is in light receiving condition or the muting function is valid
OFF when the safety light curtain is in light interrupted condition and the muting function is invalid (Note 3)
Safety output 3: ON when the emergency stop is invalid, OFF when the emergency stop is valid
OFF response: 14 ms or less (Safety output 1 and 2: including the response time of the safety light curtain)
ON response: 90 ms or less (auto-reset) / 140 ms or less (manual reset) (Note 4)
PNP open-collector transistor × 3 or NPN open-collector transistor × 3 (selectable using a slider switch)
Auxiliary output 1: ON when the muting function is invalid, OFF when the muting function is valid
Auxiliary output 2: ON when the override function is invalid, OFF when the override function is valid
Auxiliary output 3: ON when the muting lamp is normal, OFF when the muting lamp is error
Auxiliary output 4: ON when the safety light curtain is in light interrupted condition, OFF when the safety light curtain is in light receiving condition (Note 5)
Applicable muting lamp: 24 V DC, 3.6 to 30 W (L1, L2 of each unit)
Enclosure: IP40, Terminal: IP20
–10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F
Enclosure: ABS
Detachable spring-cage terminal
Net weight: 250 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
2) SF-C14EX-01 is Handy-controller SFB-HC (optional) non-compatible type.
3) Both safety output 1 and 2 are OFF when the emergency stop is valid regardless of whether the safety light curtain is in the light receiving or light interrupted condition.
4) The auto-reset cannot be used with safety output 3.
5) The auxiliary output incorporated in the SF4B / SF4B-G series is outputed.
6) Refer to p.668 for details of the specifications for the control unit SF-C14EX(-01).
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
SPECIFICATIONS
FIBER
SENSORS
LASER
SENSORS
Handy-controller
Model No.
Item
Supply voltage
SFB-HC
24 V DC ±10 % Ripple P-P10 % or less (common to safety light curtain power supply)
Current consumption
Communication method
Digital display
65 mA or less
RS-485 two-way communications (Specific procedure)
4-digit red LED display × 2 (Selected beam channels, setting contents etc. are displayed.)
Function indicator
Green LED × 9 (set function is displayed.)
Fixed blanking (Factory setting: Disabled) / Floating blanking (Factory setting: Disabled) /
Auxiliary output change (Factory setting: Negative Logic of OSSD) /
Light emitting amount control (Factory setting: Disabled) /
Muting setting change [Factory setting: All beam channels enabled, A = B, Setting of the muting lamp diagnosis
function enabled (Ver. 2 or later), Muting sensor output operation setting N.O. / N.C. (Ver. 2.1 or later)]
Interlock setting change (Factory setting: start / restart) /
External device monitoring setting change (Factory setting: Enabled, 300 ms) / Override setting changing function
60 sec. (Ver. 2.1 or later) / Setting detail monitoring /
Protecting (Factory setting: Disabled) (Factory password setting: 0000) / Initialization / Copy
Functions
Ambient temperature
Ambient humidity
–10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F
30 to 85 % RH, Storage: 30 to 85 % RH
Voltage withstandability
Insulation resistance
Cable
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
8-core shielded cable, 0.5 m 1.640 ft long, with a connector at the end (2 cables)
Material
Enclosure: ABS
Weight
Net weight: 200 g approx.
Accessories
Adapter cable: 2 cables
Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
Item
Supply voltage
SF-LAT-2N / SF-LAT-4BG (For SF4B-□G□)
3 V (LR6 battery × 2 pcs.)
1.5 V (LR6 battery) × 2 pcs. (replaceable) (Note 2)
Battery
Battery lifetime
30 hours approx. of continuous operation (LR6 battery, at +25 °C +77 °F ambient temperature)
Light source
Red semiconductor laser: Class 2 (IEC / JIS / FDA) (Max. output: 1 mW, Peak emission wavelength: 650 nm 0.026 mil) (Note 3)
Spot diameter
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
Laser alignment tool
Model No.
524
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
10 mm 0.394 in approx. (at 5 m 16.404 ft distance)
Ambient temperature
Ambient humidity
0 to +40 °C +32 to +104 °F (No dew condensation), Storage: 0 to +55 °C +32 to +131 °F
35 to 85 % RH, Storage: 35 to 85 % RH
Material
Enclosure: ABS, Mounting part: Aluminum
Weight
Net weight: 150 g approx. (without batteries)
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
2) LR6 dry cell batteries are not provided with the product. Please purchase them separately.
3) As for FDA regulation, the product complies with 21 CFR 1040.10 and 1040.11 based on Laser Notice No. 50, dated June 24, 2007, issued by CDRH
under the FDA.
Corner mirror
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
Model No.
Item
RF-SFBH-□
SF4C
BSF4-AH80
With one corner mirror: Declined to 90 %, With two corner mirrors: Declined to 80 % (When used in combination with the SF4B series)
SF2B
Ambient temperature
–10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F
SF2C
Environmental
resistance
Attenuation rate of sensing range
Ambient humidity
Vibration resistance
Shock resistance
Material
Accessories
30 to 85 % RH, Storage: 30 to 95 % RH
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Enclosure: Aluminum, Mounting bracket: Stainless steel, Mirror (rear surface mirror): Glass, Side cover: EPDM
Intermediate supporting bracket: 1 set (RF-SFBH-40/48/56/64), 2 sets (RF-SFBH-72/80/88/96)
Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
Definition of
Sensing Heights
525
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
LASER
SENSORS
I/O circuit diagram
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
Refer to the instruction manual for details.
The instruction manual can be download from our website.
I/O CIRCUIT AND WIRING DIAGRAMS
FIBER
SENSORS
Emitter
Emitter
Color code of mating cable
Color code of mating cable
(Brown) +V
(Brown) +V
AREA
SENSORS
(Red) Muting lamp output
* S1
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
470 Ω
SENSOR
OPTIONS
0.22 μF
470 Ω
SIMPLE
WIRE-SAVING
UNITS
0.22 μF
470 Ω
Internal circuit
Receiver
0.047 μF 1 kΩ
Sensor circuit
0.047 μF 1 kΩ
(Orange / Black)
Synchronization –
Users’ circuit
SF2B
SF2C
Definition of
Sensing Heights
* S1
24 V DC
±10 %
* S1
Receiver
Users’ circuit
(Orange / Black)
Synchronization –
(Orange) Synchronization +
(Brown) +V
* S1
(Shield) Output polarity setting wire
K1
(Sky-blue / White) Muting input A
(Sky-blue / Black) Muting input B
K1
(Black) OSSD 1
K2
K2
(Yellow-green) External device monitoring input
(Black) OSSD 1
(White) OSSD 2
(Gray) Interference prevention +
(Gray / Black) Interference prevention –
(White) OSSD 2
Safety Light
Curtains
BSF4-AH80
+
(Orange / Black) Synchronization –
Internal circuit
K1
K2
(Blue) 0 V
SF4C
(Yellow-green / Black)
Auxiliary output
* S1
(Blue) 0 V
Selection
Guide
SF4B-C
Load
(Gray) Interference prevention +
(Gray / Black) Interference prevention –
(Orange) Synchronization +
(Shield) Output polarity setting wire
SF4B/
SF4B-G
(Pink) Emission halt input / Reset input
(Red) Muting lamp output
0.22 μF 470 Ω
UV
CURING
SYSTEMS
SF4D
470 Ω
(Orange) Synchronization +
(Gray) Interference prevention +
(Gray / Black) Interference prevention –
HUMAN
MACHINE
INTERFACES
Safety
Components
0.22 μF
(Blue) 0 V
(Orange) Synchronization +
* S1
(Brown) +V
PLC
Safety
Control Units
470 Ω
(Pink) Emission halt input / Reset input
(Orange / Black)
Synchronization –
LASER
MARKERS
MACHINE
VISION
SYSTEMS
Load
0.22 μF
Sensor circuit
MEASUREMENT
SENSORS
FA
COMPONENTS
(Yellow) Override input
(Pale purple) Interlock setting input
24 V DC
±10 %
470 Ω
(Yellow) Override input
(Pale purple) Interlock setting input
(Shield) Output polarity setting wire
WIRE-SAVING
SYSTEMS
ENERGY
MANAGEMENT
SOLUTIONS
+
–
(Gray) Interference prevention +
(Gray / Black) Interference prevention –
0.22 μF
STATIC
CONTROL
DEVICES
* S1
Sensor circuit
Sensor circuit
PARTICULAR
USE
SENSORS
* S1
(Yellow-green / Black)
Auxiliary output
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
(Shield) Output polarity setting wire
0.22 μF
Internal circuit
Users’ circuit
0.22 μF
470 Ω
0.047 μF
1 kΩ
0.047 μF
1 kΩ
K1, K2: Force-guided relay or
magnet contactor
Internal circuit
(Yellow-green) External device monitoring input
(Sky-blue / White) Muting input A
K1
* S1
(Sky-blue / Black) Muting input B
K2
* S1
(Blue) 0 V
K1, K2: Force-guided relay or
magnet contactor
Note: The above diagram is when using a 12-core cable. If an 8-core cable
is used, the red, yellow, gray, gray / black, sky-blue / white and skyblue / black lead wires are absent.
Note: The above diagram is when using a 12-core cable. If an 8-core cable
is used, the red, yellow, gray, gray / black, sky-blue / white and skyblue / black lead wires are absent.
* S1
* S1
Switch S1
• Emission halt input / Reset input
For manual reset
Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note 1)
Open: Emission
For automatic reset
Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note 1)
Open: Emission halt
• Interlock setting input, Override input, Muting input A/B,
External device monitoring input
Vs to Vs – 2.5 V (sink current 5 mA or less): Enabled (Note 1)
Open: Disabled
Note: Vs is the applying supply voltage.
Switch S1
• Emission halt input / Reset input
For manual reset
0 to +1.5 V (source current 5 mA or less): Emission halt
Open: Emission
For automatic reset
0 to +1.5 V (source current 5 mA or less): Emission
Open: Emission halt
• Interlock setting input, Override input, Muting input A/B,
External device monitor input
0 to +1.5 V (source current 5 mA or less): Enabled
Open: Disabled
Safety Light Curtain Type 4
I/O CIRCUIT AND WIRING DIAGRAMS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
526
Refer to the instruction manual for details.
The instruction manual can be download from our website.
LASER
SENSORS
Connection example
Standard components (8-core cable): Interlock function “enabled (manual reset)”, external device monitoring function “enabled”
Emitter
The diagram at left shows the configuration when using PNP
output, interlock function “enabled (manual reset)” and external
device monitoring function “enabled”.
Color code of mating cable
(Brown) +V
* S1
In case of setting the interlock function to “disabled (automatic reset)”
(Yellow-green / Black) Auxiliary output
Cable color: Gray
(Pale purple) Interlock setting input
(Pink) Emission halt input / Reset input
Load
(Shield) Output polarity setting wire
(Blue) 0 V
(Orange) Synchronization +
Receiver
+
–
24 V DC
±10 %
Emitter
+24 V DC
* S1
(Orange / Black) Synchronization –
(Pink) Emission halt input / Reset input
(Orange / Black) Synchronization –
(Pale purple) Interlock setting input
(Brown) +V
K1
(Yellow-green) External device monitoring input
K2
(Black) OSSD 1
(White) OSSD 2
MEASUREMENT
SENSORS
(Yellow-green / Black) Auxiliary output
PLC
HUMAN
MACHINE
INTERFACES
(Yellow-green) External device monitoring input
The diagram at left shows the configuration when using NPN
output, interlock function “enabled (manual reset)” and external
device monitoring function “enabled”.
Color code of mating cable
(Brown) +V
In case of setting the interlock function to “disabled (automatic reset)”
Load
+
–
(Orange) Synchronization +
(Pale purple) Interlock setting input
(Orange / Black) Synchronization –
(Pink) Emission halt input / Reset input
(Shield) Output polarity setting wire
K1
K2
* S1
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
* Refer to the SF4B / SF4B-G instruction manual on our website for
interlock function.
In case of setting the external device monitoring function to “disabled”
(White) OSSD 2
(Yellow-green) External device monitoring input
MACHINE
VISION
SYSTEMS
0V
(Black) OSSD 1
(Blue) 0 V
Open
* S1
(Orange / Black) Synchronization –
(Brown) +V
FA
COMPONENTS
Emitter
(Orange) Synchronization +
Cable color: Gray
with black line
ENERGY
MANAGEMENT
SOLUTIONS
24 V DC
±10 %
(Blue) 0 V
Receiver
STATIC
CONTROL
DEVICES
LASER
MARKERS
Receiver
* Refer to the SF4B / SF4B-G instruction manual on our website for
external device monitoring function.
(Pink) Emission halt input / Reset input
(Yellow-green / Black) Auxiliary output
* S1
PARTICULAR
USE
SENSORS
WIRE-SAVING
SYSTEMS
Note: Vs is the applying supply voltage.
Cable color: Gray
PRESSURE /
FLOW
SENSORS
SIMPLE
WIRE-SAVING
UNITS
K1, K2: Force-guided relay
or magnet contactor
(Shield) Output polarity setting wire
(Pale purple) Interlock setting input
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
In case of setting the external device monitoring function to “disabled”
K2
Switch S1
• Emission halt input / Reset input
For manual reset
Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note)
Open: Emission
For automatic reset
Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note)
Open: Emission halt
Emitter
AREA
SENSORS
SENSOR
OPTIONS
(Blue) 0 V
* S1
MICRO
PHOTOELECTRIC
SENSORS
* Refer to the SF4B / SF4B-G instruction manual on our website for
interlock function.
Emitter
K1
(Shield) Output polarity setting wire
PHOTOELECTRIC
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Open
(Orange) Synchronization +
Cable color: Gray
with black line
FIBER
SENSORS
K1
K2
Emitter
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
K1, K2: Force-guided relay
or magnet contactor
Switch S1
• Emission halt input / Reset input
For manual reset
0 to +1.5 V (source current 5 mA or less): Emission halt
Open: Emission
For automatic reset
0 to +1.5 V (source current 5 mA or less): Emission
Open: Emission halt
SF4D
SF2B
(Yellow-green / Black) Auxiliary output
Receiver
(Yellow-green) External device monitoring input
* Refer to the SF4B / SF4B-G instruction manual on our website for
external device monitoring function.
SF2C
Definition of
Sensing Heights
527
Safety Light Curtain Type 4
I/O CIRCUIT AND WIRING DIAGRAMS
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Connection example
Muting control components (12-core cable, with interference prevention wires): Interlock function “disabled (automatic reset)”, external device monitoring function “disabled”
Color code of mating cable
Emitter
(Red) Muting lamp output
Cable color: Gray
The diagram at left shows the configuration when using PNP
output, interlock function “disabled (automatic reset)” and external
device monitoring function “disabled”.
(Brown) +V
* S1
(Gray) Interference prevention +
Uses when the interference
prevention function is used
(Gray / Black) Interference prevention –
(Yellow) Override input
INDUCTIVE
PROXIMITY
SENSORS
(Pale purple) Interlock setting input: Open
(Pink) Emission halt input / Reset input
(Shield) Output polarity setting wire
(Blue) 0 V
(Orange) Synchronization +
PARTICULAR
USE
SENSORS
SIMPLE
WIRE-SAVING
UNITS
Receiver
Cable color: Gray
with black line
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
* S1
Emitter
(Pink) Emission halt input / Reset input
(Orange / Black) Synchronization –
(Orange / Black) Synchronization –
(Orange) Synchronization +
(Brown) +V
+24 V DC
* S1
(Pale purple) Interlock setting input
* S1
(Gray) Interference prevention +
Uses when the interference
* S1
prevention function is used
(Gray / Black) Interference prevention –
(Sky-blue / White) Muting input A
(Sky-blue / Black) Muting input B
(Yellow-green) External device monitoring input
(Black) OSSD 1
(White) OSSD 2
K1
K1, K2:
(Shield) Output polarity setting wire
Force-guided relay
K2
(Blue) 0 V
or magnet contactor
Color code of mating cable
Emitter
* Refer to the SF4B / SF4B-G instruction manual on our website for
interlock function.
In case of setting the external device monitoring function to “enabled”
+24 V DC
K1
Receiver
K2
(Yellow-green)
External device monitoring input
(Black) OSSD 1
K1
(White) OSSD 2
K2
K1, K2: External device 0 V
* Refer to the SF4B / SF4B-G instruction manual on our website for
external device monitoring function.
The diagram at left shows the configuration when using NPN
output, interlock function “disabled (automatic reset)” and external
device monitoring function “disabled”.
(Brown) +V
(Shield) Output polarity setting wire
(Yellow) Override input
* S1
(Pale purple) Interlock setting input: Open
(Pink) Emission halt input / Reset input
(Gray) Interference prevention +
Uses when the interference
prevention function is used
(Gray / Black) Interference prevention –
(Yellow-green / Black) Auxiliary output * S1
+
–
24 V DC
±10 %
In case of setting the interlock function to “enabled (manual reset)”
• When the interlock function is “enabled (manual reset)”,
the override function cannot be used.
Emitter
(Red) Muting lamp output
(Pale purple) Interlock setting input
(Blue) 0 V
(Orange) Synchronization +
Safety
Control Units
Receiver
SF4D
Cable color: Gray
with black line
SF4B-C
SF4C
BSF4-AH80
SF2B
Definition of
Sensing Heights
24 V DC
±10 %
Selection
Guide
SF2C
+
–
Note: Vs is the applying supply voltage.
Safety Light
Curtains
SF4B/
SF4B-G
• When the interlock function is “enabled (manual reset)”,
the override function cannot be used.
Switch S1
• Emission halt input / Reset input
For manual reset
Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note), Open: Emission
For automatic reset
Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note), Open: Emission halt
• Override input, Muting input A/B, External device monitoring input
Vs to Vs – 2.5 V (sink current 5 mA or less): Enabled (Note), Open: Disabled
Cable color: Gray
Safety
Components
In case of setting the interlock function to “enabled (manual reset)”
* S1
(Yellow-green / Black) Auxiliary output
PRESSURE /
FLOW
SENSORS
SENSOR
OPTIONS
Refer to the instruction manual for details.
The instruction manual can be download from our website.
(Orange) Synchronization +
(Brown) +V
K1
(Shield) Output polarity setting wire
K2
(Black) OSSD 1
(White) OSSD 2
(Gray) Interference prevention +
Uses when the interference
prevention function is used
(Gray / Black) Interference prevention –
(Yellow-green) External device monitoring input
(Sky-blue / White) Muting input A
* S1
(Sky-blue / Black) Muting input B
* S1
(Pink) Emission halt input / Reset input
* S1
(Orange / Black) Synchronization –
(Orange / Black) Synchronization –
(Blue) 0 V
* S1
0V
* Refer to the SF4B / SF4B-G instruction manual on our website for
interlock function.
In case of setting the external device monitoring function to “enabled”
+24 V DC
K1, K2:
Force-guided relay
or magnet contactor
Switch S1
• Emission halt input / Reset input
For manual reset
0 to +1.5 V (source current 5 mA or less): Emission halt, Open: Emission
For automatic reset
0 to +1.5 V (source current 5 mA or less): Emission, Open: Emission halt
• Override input, Muting input A/B, External device monitoring input
0 to +1.5 V (source current 5 mA or less): Enabled, Open: Disabled
K1
Receiver
K2
(Black) OSSD 1
(White) OSSD 2
(Yellow-green)
External device monitoring input
K1
K2
0V
K1, K2: External device
* Refer to the SF4B / SF4B-G instruction manual on our website for
external device monitoring function.
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Refer to the instruction manual for details.
The instruction manual can be download from our website.
I/O CIRCUIT AND WIRING DIAGRAMS
SF4B / SF4B-G series wiring diagram (Control Category 4)
When SF-C11 is connected to the safety light curtain, be
sure to use the following mating cable.
SFB-CB□, SFB-CCJ10□
For PNP output (minus ground)
• Set the safety light curtain input polarity selection switch
to the PNP side and ground the 0 V line.
Safety light curtain input polarity selection switch
A1
L1
RESET
(Note 1)
(Note 1)
A B
(Note 2) X1 X2 X3
F
Receiver side
connector
FUSE1
Terminal
33 41
K1
T2
AUX
F.G.
0V
TEST
(Note 3)
INTER_LOCK
14 24
34 42
L1 L2 L3
KB
KA
N
KB
KA
• In the above
diagram, set
the safety
light curtain
input polarity
selection
switch to the
NPN side and
ground the +
side.
Safety light curtain input
polarity selection switch
+24 V DC
F.G.
X1 X2
Emitter side
connector
X3
A
1
3
SF-C11 control circuit
OUT
A2
AUX
T2
7
4
6
NPN
PNP
INTER_LOCK
Reset output terminal
X2
Reset input terminal (Manual)
X3
Reset input terminal (Automatic)
Not used
Test output terminal
T2
Test input terminal
AUX
Semiconductor auxiliary output
Connector
pin No.
8
5
Ui
X1
Pin layout for safety light curtain connectors
2
FAULT
T1
Emitter side
connector
Receiver side
connector
1
Interlock
OSSD 2
2
+24 V DC
+24 V DC
3
Emission halt
OSSD 1
4
Auxiliary output
EDM (External relay monitor)
5
Synchronization wire + Synchronization wire +
6
Synchronization wire – Synchronization wire –
7
0V
0V
8
Shield wire
Shield wire
SF-C12
SF4B / SF4B-G series wiring diagram (Control Category 4)
MPCE1
MPCE2
FUSE
R+
FB1
FB2
FB3
FB4
32
31
24
23
14
13
A1
A2
FG
PNP
FUSE
NPN
Receiver side connector
Safety light curtain input
polarity selection switch
X1
X2
T1
T2
Safety output Auxiliary Power input
output
24 V DC ±10 %
Note: The above diagram is when using manual reset. If automatic reset is
used, connect a normally closed type pushbutton switch between T1
and T2 and leave between X1 and X2 open.
For NPN output (plus ground)
• In the above diagram, set the two safety light curtain
input polarity selection switches to the NPN side and
connect the F.G. terminal to the + side.
Terminal
FG
A2
A1
13-14, 23-24
31-32
FB4
FB3
FB2
FB1
Function
Frame ground (F.G.) terminal
0V
+24 V DC
Safety output (NO contact × 2)
Auxiliary output (NC contact × 1)
External relay
monitor terminal 2
External relay
monitor terminal 1
R+
FB1
FB2
FB3
FB4
32
31
24
23
14
13
A1
A2
FG
Terminal arrangement
diagram
E+
• Set the two safety light curtain input polarity select
switches to the PNP side and connect the FG terminal to
the 0 V line.
X1
X2
T1
T2
When SF-C12 is connected to the safety light curtain, be
sure to use the following mating cable.
SFB-CB05-MU, SFB-CCJ10□-MU
For PNP output (minus ground)
E+
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
0 V TEST
Emission halt input switch
(Note)
(Note)
Interference
prevention wire
Emitter side connector
MICRO
PHOTOELECTRIC
SENSORS
PRESSURE /
FLOW
SENSORS
Auxiliary output (NC contact × 1)
T1
B
F
Receiver side
connector
0V
B
RESET
A1
+24 V DC
A2
A
M
3
Notes: 1) T
he above diagram is when using manual reset. If
automatic reset is used, disconnect the lead from X2 and
connect it to X3. In this case, a reset (RESET) button is not needed.
2) Use a momentary-type switch as the reset (RESET) button.
3) Emission halt occurs when the test (TEST) button is open, and
emission occurs when the test (TEST) button is short-circuited. If
not using the test (TEST) button, short-circuit T1 and T2.
For NPN output (plus ground)
A1
41-42
FAULT
T1
KA, KB: Force-guided relay or
magnet contactor
Function
13-14, 23-24, 33-34 Safety output (NO contact × 3)
K2
OUT
PHOTOELECTRIC
SENSORS
AREA
SENSORS
Terminal arrangement diagram
FUSE2
13 23
NPN
SF-C11 control circuit PNP
Ui
Emitter side
connector
A2
FIBER
SENSORS
LASER
SENSORS
SF-C11
+24 V DC
528
Terminal
R+
R–
E+
E–
T2
T1
X2
X1
Function
Interference prevention wire – (Receiver side)
Interference prevention wire + (Receiver side)
Interference prevention wire – (Emitter side)
Interference prevention wire + (Emitter side)
Emission halt input
terminal
Automatic reset / manual reset selection terminal
Manual reset: X1 – X2 short-circuited
1
10
2
3
12
11
8
7
6
5
4
Note: Input and
output for pin
Nos. 11 and 12
are not used by
this device.
Connector
pin No.
1
2
3
4
5
6
7
8
9
10
11
12
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
Pin layout for safety light curtain connectors
9
UV
CURING
SYSTEMS
Emitter side
connector
Interlock
+24 V DC
Emission halt
Auxiliary output
Synchronization wire +
Synchronization wire –
0V
Shield wire
Interference prevention wire +
Interference prevention wire –
(Override input)
(Muting lamp output)
Receiver side
connector
OSSD 2
+24 V DC
OSSD 1
EDM (External relay monitor)
Synchronization wire +
Synchronization wire –
0V
Shield wire
Interference prevention wire +
Interference prevention wire –
(Muting input 1)
(Muting input 2)
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
529
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
Safety Light Curtain Type 4
SF-C13
SF4B / SF4B-G series wiring diagram (Control Category 4)
For PNP output (minus ground)
For NPN output (plus ground)
• Connect the safety light curtain control outputs OSSD 1
and OSSD 2 to S1 and S2 respectively.
• Connect the safety light curtain control outputs OSSD 1
and OSSD 2 to S4 and S2 respectively and ground the +
side.
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
(Orange / Black) Synchronization –
Emitter
PRESSURE /
FLOW
SENSORS
PARTICULAR
USE
SENSORS
(Orange)
Synchronization +
+V (Brown)
+24 V DC
Output Emission
halt Auxiliary output Interlock setting
polarity
setting wire input / Reset (Yellow-green / input (Pale purple)
Black) Open +V (Brown)
(Shield) input (Pink)
Load
0 V (Blue)
0 V (Blue)
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Output
Emission halt Auxiliary output Interlock setting
polarity
input / Reset input (Yellow-green / input (Pale purple)
setting wire
(Pink)
Black) Open
(Shield)
0V
Load +V (Brown)
(Blue)
OSSD 2 (White)
OSSD 1 (Black)
L1
L1
RESET
(Note 1,2)
A1
S1
S2 S3
(Note 1) FUSE1
S4 X1 X2
X3
F
13 23
(Note 1) FUSE1
FUSE2
33 41
A1
F.G.
S1
S2 S3 S4
X1
X2
F
K1
Ui
A2
0V
AUX
F.G.
FAULT
14 24 34 42
KA, KB: Force-guided relay or
KB
magnet contactor
KA
N
FUSE2
33 41
RESET
(Note 1,2)
SF-C13 control circuit
K2
K2
INTER_LOCK
X3 13 23
K1
Ui
SF-C13 control circuit
OUT
Output
polarity
setting wire
(Shield)
0 V (Blue)
External device monitoring input (Yellow-green)
OSSD 2 (White)
PLC
FA
COMPONENTS
(Orange)
Synchronization +
+V (Brown)
+24 V DC
Output
polarity
setting wire
(Shield)
Receiver
Cable color:
Gray with black line
Cable color: Gray
OSSD 1 (Black)
LASER
MARKERS
ENERGY
MANAGEMENT
SOLUTIONS
(Orange / Black) Synchronization –
Emitter
External device monitoring input (Yellow-green)
MEASUREMENT
SENSORS
HUMAN
MACHINE
INTERFACES
Receiver
Cable color:
Gray with black line
Cable color: Gray
WIRE-SAVING
SYSTEMS
STATIC
CONTROL
DEVICES
Refer to the instruction manual for details.
The instruction manual can be download from our website.
I/O CIRCUIT AND WIRING DIAGRAMS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
INDUCTIVE
PROXIMITY
SENSORS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
L1 L2 L3
OUT
KB
KA
M
3
Notes: 1) The above diagram is when using manual reset. If automatic reset
is used, disconnect the lead from X2 and connect it to X3. In this
case, a reset (RESET) button is not needed.
2) Use a momentary-type switch as the reset (RESET) button.
A2
0V
AUX
INTER_LOCK
FAULT
14 24 34 42
KA, KB: Force-guided relay or
KB
magnet contactor
KA
N
L1 L2 L3
KA
M
3
Notes: 1) T
he above diagram is when using manual reset. If automatic reset
is used, disconnect the lead from X2 and connect it to X3. In this
case, a reset (RESET) button is not needed.
2) Use a momentary-type switch as the reset (RESET) button.
Terminal arrangement diagram
A1
A2
S1
S2
S3
S4
AUX
X1
X2
X3
13
14
23
24
33
34
41
42
Terminal
Function
A1
+24 V DC
A2
0V
S1 to S4
Safety light curtain control output
(OSSD) input terminal
AUX
Semiconductor auxiliary output
X1
Reset output terminal
X2
Reset input terminal (Manual)
X3
Reset input terminal (Automatic)
13-14, 23-24, 33-34
Safety output (NO contact × 3)
41-42
Auxiliary output (NC contact × 1)
A terminal block is required for wiring of
safety light curtain side.
KB
When SF-C13 is connected to the safety light curtain,
be sure to use the following descrete wire mating
cable.
SFB-CCB□(-MU), SFB-CC□(-MU)
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Refer to the instruction manual for details.
The instruction manual can be download from our website.
I/O CIRCUIT AND WIRING DIAGRAMS
SF4B / SF4B-G series wiring diagram (Control Category 4)
For PNP output (minus ground)
• Set the output polarity selection switch to the PNP side and ground the 0 V line.
+24 V DC
(Note 1)
KA
RESET
KB (Note 2)
(Note 1)
KC
RESET
KD (Note 2)
PLC etc.
KE RESET
KF (Note 2)
• When SF-C14EX is connected to
the safety light curtain, be sure to
use the following mating cable.
SFB-CB□-EX, SFB-CCJ10□
• If the NO (Normally Open) contact
switch is used as a muting sensor,
wire it as shown in the figure below.
S3+ S3 S3– S4+ S4 S4–
A1 S11 S12 S21 S22 X11 X12 X13 X21 X22 X23 X31 X32 AUX1 AUX2 AUX3 AUX4 IE+ IE– IR+ IR–
Receiver side NPN
Output polarity
connector
selection switch
PNP
SF-C14EX(-01) control circuit
A2 S3+ S3 S3– S4+ S4 S4– T1 T2 O1 O2 L1+ L1– L2+ L2– 14 24 34 44 54 64
KB
KD
KF
+V OUT 0 V +V OUT 0 V
0V
F.G.
KA
KC
KE
Muting sensor 2
(NPN output type)
Override input
TEST
Muting lamp
output 1
3.6 to 30 W
Muting lamp
output 2
3.6 to 30 W
KA to KF: Force-guided relay or
magnet contactors.
• Set the output polarity selection switch to the NPN side and ground the side of the power supply input.
+24 V DC
KA
RESET
KB (Note 2)
KE RESET
KF (Note 2)
Emitter side
connector
A2 S3+ S3 S3– S4+ S4 S4– T1 T2 O1 O2 L1+ L1– L2+ L2– 14 24 34 44 54 64
KB
KD
KF
+V OUT 0 V +V OUT 0 V
KA
Muting sensor 1
(PNP output type)
Override input
Terminal arrangement
diagram
Muting lamp
output 1
3.6 to 30 W
Function
Terminal
14 Safety output 1, Beam received
/ Beam interrupted output of the
24 safety light curtain
34 Safety output 2, safety light
curtain output including the
44 muting function
54 Safety output 3
64 Emergency stop output
S3+
S3
S3–
S4+
S4
S4–
KC
TEST
Muting sensor 2
(NPN output type)
Muting lamp
output 2
3.6 to 30 W
Terminal
KE
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
Notes: 1) T
he left diagram is when using manual reset. If automatic reset
is used, disconnect the lead from X12 and connect it to X13,
and disconnect the lead from X22 and connect it to X23, as
shown by the dotted lines. In this case, a reset (RESET) button
is not needed. Terminals X31 to X32 are for manual reset only.
2) Use a momentary-type switch for the reset (RESET) button.
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
KA to KF: Force-guided relay or
magnet contactors.
Function
S11 Emergency stop
S12 contact input
2 NC input
S21 Between S11 and S12
S22 Between S21 and S22
X11
T1 Test input terminal
Open: Test mode
T2 Short-circuit: Normal operation
O1 Override input terminal
Open: Invalid
O2 Short-circuit: Valid
L1+ Muting lamp
L1– output 1
AUX1 Auxiliary output 1, Muting output
L2+ Muting lamp
L2– output 2
IR+ Interference prevention terminal, Receiver side +
A2 0 V
SENSOR
OPTIONS
HUMAN
MACHINE
INTERFACES
+24 V DC
Safety output 1 reset input
X12 X11 - X12: Manual reset
X11 - X13: Automatic reset
Muting sensor input 1 X13
(PNP output type)
X21
S3+, S3–: Power supply
Safety output 2 reset input
S3: Sensor output
X22 X21 - X22: Manual reset
X21 - X23: Automatic reset
Muting sensor input 2 X23
(NPN output type)
X31 Safety output 3 reset input
S4+, S4–: Power supply
S4: Sensor output
X32 X31 - X32: Manual reset
A1 +24 V DC
PARTICULAR
USE
SENSORS
PLC
SF-C14EX(-01) control circuit
0V
INDUCTIVE
PROXIMITY
SENSORS
PLC etc.
F.G.
A1 S11 S12 S21 S22 X11 X12 X13 X21 X22 X23 X31 X32 AUX1 AUX2 AUX3 AUX4 IE+ IE– IR+ IR–
Receiver side NPN
Output polarity
connector
selection switch
PNP
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
LASER
MARKERS
(Note 1)
KC
RESET
KD (Note 2)
AREA
SENSORS
STATIC
CONTROL
DEVICES
For NPN output (plus ground)
(Note 1)
MICRO
PHOTOELECTRIC
SENSORS
SIMPLE
WIRE-SAVING
UNITS
0V
Notes: 1) T
he above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X12 and connect it to X13, and disconnect the lead from
X22 and connect it to X23, as shown by the dotted lines. In this case, a reset (RESET) button is not needed. Terminals X31 to X32 are for manual reset only.
2) Use a momentary-type switch for the reset (RESET) button.
Emergency
stop button
PHOTOELECTRIC
SENSORS
PRESSURE /
FLOW
SENSORS
• If the emergency stop button is
not used, short-circuit between the
terminals S11 to S12 and S21 to
S22 directly.
Emitter side
connector
Muting sensor 1
(PNP output type)
FIBER
SENSORS
LASER
SENSORS
SF-C14EX(-01)
Emergency
stop button
530
AUX2 Auxiliary output 2, Override output
AUX3 Auxiliary output 3, Blown lamp output
AUX4 Auxiliary output 4, safety light curtain auxiliary output
IE+ Interference prevention terminal, Emitter side +
IE– Interference prevention terminal, Emitter side –
IR– Interference prevention terminal, Receiver side –
Pin layout for safety light curtain connectors
2
1
Connector
pin No.
8
3
7
4
Receiver
side
connector
Selection
Guide
Safety Light
Curtains
Safety
Control Units
1
Interference prevention Interference prevention
wire +
wire +
2
+24 V DC
3
Interference prevention Interference prevention
wire –
wire –
4
Auxiliary output
Not used
SF4B-C
Synchronization
wire +
Synchronization
wire –
Synchronization
wire +
Synchronization
wire –
SF4C
7
0V
0V
8
Shield wire
Shield wire
6
5
Emitter
side
connector
5
6
+24 V DC
Safety
Components
SF4D
SF4B/
SF4B-G
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
531
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Refer to the instruction manual for details.
The instruction manual can be download from our website.
PRECAUTIONS FOR PROPER USE
Interlock function
• The selection of manual reset / automatic reset is available
by applying the interlock input wiring. The interlock
becomes available by selecting manual reset.
(Refer to the SF4B / SF4B-G instruction manual for details.)
Emission halt function
• This function stops the emission process of the emitter.
You can select whether emission is on or halted by
means of the connection status for the emission halt
input / reset input wire (pink).
• During emission halt, the control outputs (OSSD 1,
OSSD 2) become OFF status.
• By using this function, malfunction due to extraneous
noise or abnormality in the control outputs (OSSD 1,
OSSD 2) and the auxiliary output can be determined
even from the machinery side.
• Normal operation is restored when the emission halt input /
reset input wire (pink) is connected to 0 V or +V.
(Refer to the SF4B / SF4B-G instruction manual for details.)
Auxiliary output (Non-safety output)
• This safety light curtain incorporates the auxiliary output
(yellowgreen / black) for the non-safety output. The auxiliary
output is incorporated with the emitter.
(Refer to the SF4B / SF4B-G instruction manual for details.)
External device monitoring function
• This is the function for checking whether the external safety
relay connected to the control outputs (OSSD 1, OSSD 2) perform
normally in accordance with the control outputs (OSSD 1, OSSD 2)
or not. Monitor the contacting point “b” of the external safety relay,
and if any abnormality such as deposit of the contacting point,
etc. is detected, change the status of the safety light curtain into
lockout one, and turn OFF the control outputs (OSSD 1, OSSD 2).
(Refer to the SF4B / SF4B-G instruction manual for details.)
Muting function
• This function turns the safety function of this safety
light curtain into disabled temporarily. When the control
outputs (OSSD 1, OSSD 2) are ON, this function is
available for passing the workpiece through the sensing
area of the safety light curtain without stopping the
machinery.
The muting function becomes valid when all the
conditions listed below are satisfied.
However, this function connot be used with the
SF4B-□-03.
1 The control outputs (OSSD 1, OSSD 2) shall be ON.
2 The incandescent lamp with 3 to 10 W shall be
connected to the muting lamp output (red).
3 The output of the muting sensors A and B shall be
changed from OFF (open) to ON. At this time, the
time difference occurred by changing the output of the
muting sensors A and B into ON status shall be within
0.03 to 3 sec.
• The following devices, photoelectric sensor with
semiconductor output, inductive proximity sensor,
position switch on N.O. (Normally open) contact, etc. are
available for applying to the muting sensor.
• In case of using the muting function, please order 12-core
cable.
(Refer to the SF4B / SF4B-G instruction manual for details.)
Override function
• This function sets the safety function of this safety light
curtain enabled forcibly. When using the muting function,
the override function can be used to start the machinery
at times such as when the control outputs (OSSD 1 and
OSSD 2) are OFF or when the muting sensors are ON
when the line is to be started.
The override function becomes valid when all the
conditions listed below are satisfied.
However, this function cannot be used with the
SF4B-□-03.
(Refer to the SF4B / SF4B-G instruction manual for details.)
Series connection
Connectable up to 3 sets of safety light curtains
(however, 192 beam channels max.)
(Refer to the SF4B / SF4B-G instruction manual for details.)
Parallel connection
Connectable up to 3 sets of safety light cartains
(Refer to the SF4B / SF4B-G instruction manual for details.)
Series and parallel mixed connection
Connectable up to 3 sets of safety light curtains
(however, 192 beam channels max.)
(Refer to the SF4B / SF4B-G instruction manual for details.)
Wiring
Refer to the applicable regulations for the
region where this device is to be used when
setting up the device. In addition, make sure
that all necessary measures are taken to
prevent possible dangerous operating errors
resulting from earth faults.
• Make sure to carry out the wiring in the power supply off
condition.
• Verify that the supply voltage variation is within the rating.
• If power is supplied from a commercial switching
regulator, ensure that the frame ground (F.G.) terminal of
the power supply is connected to an actual ground.
• In case noise generating equipment (switching regulator,
inverter motor, etc.) is used in the vicinity of this sensor,
connect the frame ground (F.G.) terminal of the
equipment to an actual ground.
• Do not run the wires together with high-voltage lines or
power lines or put them in the same raceway. This can
cause malfunction due to induction.
Others
• This device has been developed / produced for industrial
use only.
• Do not use during the initial transient time (2 sec.) after
the power supply is switched on.
• Avoid dust, dirt and steam.
• Take care that the safety light curtain does not come in
direct contact with water, oil, grease, or organic solvents,
such as, thinner, etc.
• Take care that the safety light curtain is not directly
exposed to fluorescent light from a rapid-starter lamp
or a high frequency lighting device, as it may affect the
sensing performance.
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Refer to the instruction manual for details.
The instruction manual can be download from our website.
PRECAUTIONS FOR PROPER USE
• When this device is used in the “PSDI
mode”, an appropriate control circuit must
be configured between this device and the
machinery. For details, be sure to refer to the
standards or regulations applicable in each
region or country.
• To use this device in the U.S.A., refer to
OSHA 1910. 212 and OSHA 1910. 217 for
installation, and in Europe, refer to EN ISO
13855 as well. Observe your national and
local requirements before installing this
product.
• This catalog is a guide to select a suitable product. Be
sure to read instruction manual prior to its use.
• Both emitter and receiver are adjusted before
shipment, please apply both emitter and receiver with
the same serial No. The serial No. is indicated on the
plates of both emitter and receiver.
(Indicated under model No.)
• Make sure to carry out the test run before regular operation.
• This safety system is for use only on machinery in which
the dangerous parts can be stopped immediately, either
by an emergency stop unit or by disconnecting the power
supply. Do not use this system with machinery which
cannot be stopped at any point in its operation cycle.
Sensing area
• Make sure to install this device such that
any part of the human body must pass
through its sensing area in order to reach
the dangerous parts of the machinery. If
the human body is not detected, there is a
danger of serious injury or death.
• Do not use any reflective type or
retroreflective type arrangement.
• Multiple receivers (emitters) cannot be
connected for use with a single emitter
(receiver).
Example of correct sensing area setup
Dangerous part
Sensing area
Protective structure
532
LASER
SENSORS
Safety distance
• Calculate the safety distance correctly, and
always maintain a distance which is equal to
or greater than the safety distance, between
the sensing area of this safety light curtain
and the dangerous parts of the machinery.
(Please check the latest standards for
the equation.) If the safety distance is
miscalculated or if sufficient distance is not
maintained, there is a danger of serious
injury or death.
• Before designing the system, refer to the
relevant standards of the region where this
device is to be used and then install this device.
Dangerous part
of machine
Emitter
S
Sensing area
Example of incorrect sensing area setup
Dangerous part
Sensing area
Dangerous part
Sensing
area
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
Sensing area
(beam axis)
Receiver
S: Safety distance
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
The sizes of the minimum sensing objects
for this device vary depending on whether
or not the floating blanking function is being
used. Calculate the safety distance with the
proper size of the minimum sensing object and
appropriate equation.
Size of minimum sensing object when applying floating blanking function
Min. sensing object when applying floating blanking function
Setting (Note)
Invalid
1 beam channel 2 beam channels 3 beam channels
SF4B-F□(G) (Min. sensing object ø14 mm ø0.551 in) ø14 mm ø0.551 in ø24 mm ø0.945 in ø34 mm ø1.339 in ø44 mm ø1.732 in
SF4B-H□(G) (Min. sensing object ø25 mm ø0.984 in) ø25 mm ø0.984 in ø45 mm ø1.772 in ø65 mm ø2.559 in ø85 mm ø3.346 in
SF4B-A□(G) (Min. sensing object ø45 mm ø1.772 in) ø45 mm ø1.772 in ø85 mm ø3.346 in ø125 mm ø4.921 in ø165 mm ø6.496 in
Note: R
efer to p.507 for the floating blanking function. However, the floating
blanking function cannot be used with the SF4B-□-01,
the SF4B-□-03 and the SF-C14EX-01.
• The safety distance is calculated using the equations
given on the following pages when a person moves
perpendicularly (normal intrusion) into the sensing area of
the device. If the intrusion direction is not perpendicular,
always check the related standards (regional, machine
standards, etc.)
For use based on EN ISO 13855 / ISO 13855 / JIS B 9715
Dangerous part
FIBER
SENSORS
For intrusion direction perpendicular to the sensing area
• Equation 1
S=K×T+C
S: S
afety distance (mm)
Minimum required distance between the sensing area
surface and the dangerous parts of the machine
K: Intrusion velocity of operator’s body or object (mm/sec.)
Normally taken as 2,000 (mm/sec.) for calculation
T: R
esponse time of total equipment (sec.)
T = Tm + TSF4B
Tm: Maximum halting time of machinery (sec.)
TSF4B: Response time of the SF4B / SF4B-G series
(sec.)
C: Additional distance calculated from the size of the
minimum sensing object of the safety light curtain
(mm)
However, the value of “C” cannot be less than 0.
C = 8 × (d – 14)
d: Minimum sensing object diameter (mm)
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
533
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
PRECAUTIONS FOR PROPER USE
• For calculating the safety distance “S”, there are the
following five cases.
First calculate by substituting the value K = 2,000
(mm/sec.) in the equation above. Then, classify the
obtained value of “S” into three cases, 1) S < 100, 2)
100 ≤ S ≤ 500, and 3) S > 500. For Case 3) S > 500,
recalculate by substituting the value K = 1,600 (mm/
sec.). After that, classify the calculation result into
two cases, 4) S ≤ 500 and 5) S > 500. For details,
refer to the instruction manual enclosed with this
product. For calculating “Tm” (maximum halt time of
the machinery), use a special device called a “brake
monitor”.
When this device is used in the “PSDI mode”, an
appropriate safety distance “S” must be calculated.
For details, be sure to refer to the standards or
regulations applicable in each region or country.
• Equation
S=K×T+C
S: Safety distance (mm)
K: Intrusion velocity of operator’s body or object (mm/sec.)
Taken as 1,600 (mm/sec.) for calculation
T: R
esponse time of total equipment (sec.)
T = Tm + TSF4B
Tm: Maximum halting time of machinery (sec.)
TSF4B: Response time of the SF4B / SF4B-G series (sec.)
C: Additional distance calculated from the size of the
minimum sensing object of the safety light curtain (mm)
C = 850 (mm) (Constant)
For use based on ANSI B11.19
• Equation 2
S = K× (TS + TC + TSF4B + Tbm) + Dpf
S: S
afety distance (mm)
Minimum required distance between the sensing area
surface and the dangerous parts of the machine
K: Intrusion velocity {Recommended value in OSHA is 63
(inch/sec.) ≈ 1,600 (mm/sec.)}
ANSI B11.19 does not define the intrusion velocity
“K”. When determining “K”, consider possible factors
including physical ability of operators.
TS: Halting time calculated from the operation time of the
control element (air valve, etc.) (sec.)
TC: Maximum response time of the control circuit required
for functioning the brake (sec.)
TSF4B: Response time of safety light curtain (sec.)
Tbm: Additional halting time tolerance for the brake
monitor (sec.)
The following equation holds when the machine is
equipped with a brake monitor.
Tbm = Ta – (Ts + Tc)
Ta: Setting time of brake monitor (sec.)
When the machine is not equipped with a brake
monitor, it is recommended that 20 % or more of
(Ts + Tc) is taken as additional halting time.
Dpf: Additional distance calculated from the size of the
minimum sensing of the safety light curtain (mm)
SF4B-F□(G): Dpf = 23.8 mm 0.937 in
SF4B-H□(G□): Dpf = 61.2 mm 2.409 in
SF4B-A□(G): Dpf = 129.2 mm 5.087 in
Dpf =
3.4 × (d – 0.276) (inch)
≈ 3.4 × (d – 7) (mm)
d: Minimum sensing object diameter 0.552 (inch) ≈ 14 (mm) SF4B-F□(G)
Minimum sensing object diameter 0.985 (inch) ≈ 25 (mm) SF4B-H□(G□)
Minimum sensing object diameter 1.772 (inch) ≈ 45 (mm) SF4B-A□(G)
Refer to the instruction manual for details.
The instruction manual can be download from our website.
Handy-controller
This device enables to set each function
using the handy-controller SFB-HC (optional).
(However, a handy-controller cannot be used
with the SF4B-□-01, the SF4B-□-03
and the SF-C14EX-01.) Among the functions,
the contents related to the safety distance such
as the size of the minimum sensing object and
response time are varied depending on the
setting condition. When setting each function,
re-calculate the safety distance, and make
enough space larger than the calculated safety
distance. Failure to do so might cause the
accident that the device cannot stop quickly
before reaching the dangerous area of the
machinery, resulting in the serious injury or
death.
• Refer to the instruction manual of the handy-controller
for details of the function settings for using handycontroller SFB-HC (optional).
Corner mirror
• Be sure to carry out maintenance while
referring to the instruction manual for
the SF4B / SF4B-G series of safety light
curtains.
• Do not use if dirt, water, or oil, etc. is
attached to the reflective surface of this
product. Appropriate sensing range may not
be maintained due to diffusion or refraction.
• Make sure that you have read the instruction
manual for the corner mirror thoroughly
before setting up the corner mirrors
and safety light curtains, and follow the
instructions given. If the equipment is not set
up correctly as stipulated in the instruction
manual, incident light errors may result in
unexpected situations which may result in
serious injury or death.
• Please download the instruction manuals
from our website.
• Safety light curtain SF4B / SF4B-G series
cannot be used as a retroreflective type.
Avoid installing the safety light curtain as
a retroreflective type when this product is
applied.
• The mirror part of this product is made of
glass. Note that if it is broken, the glass
shards may fly apart.
• Do not use if crack or breakage appears on
the reflective surface of this product. Proper
sensing range may not be maintained due to
diffusion or refraction.
If crack or breakage appears on the
reflective surface of this product, replace the
product.
• When adjusting beam channels with a laser
alignment tool, etc., take sufficient care that
the laser beam reflected by this product does
not enter the eyes.
• Failure to follow the above items may result
in death or serious injury.
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Safety Light Curtain Type 4
DIMENSIONS (Unit: mm in)
534
The CAD data can be downloaded from our website.
SF4B-□
LASER
SENSORS
Not available for the robust type SF4B-□G□ Safety light curtain
Assembly dimensions
Mounting drawing for the safety light curtains using the standard mounting brackets MS-SFB-1 (optional) and the intermediate
supporting brackets.
43
1.693
42
1.654
30 1.181
15 0.591
28 1.102
18 0.709
5.5 0.217
42
1.654
28 1.102
18 0.709
5.5 0.217
30 1.181
15 0.591
43
1.693
30 1.181
18 0.709
27
1.063
43
1.693
28
1.102
28 1.102
14 0.551
5.5 0.217
43
1.693
27
1.063
28
1.102
28 1.102
14 0.551
FIBER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
30 1.181
18 0.709
5.5 0.217
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
5.5
1.5 0.217
0.059
50
1.969
5.5
0.217
5.5
0.217 1.5
0.059
50
1.969
50
1.969
Display
section
19
0.748
50
1.969 86.6
E 3.409
2
0.079
D
70.5
2.776
G
H 5
0.197
A
SF4B-F39□ SF4B-H20□ SF4B-A10□
SF4B-F47□ SF4B-H24□ SF4B-A12□
SF4B-F55□ SF4B-H28□ SF4B-A14□
SF4B-F63□ SF4B-H32□ SF4B-A16□
SF4B-F71□ SF4B-H36□ SF4B-A18□
SF4B-F79□ SF4B-H40□ SF4B-A20□
SF4B-F95□ SF4B-H48□ SF4B-A24□
SF4B-F111□ SF4B-H56□ SF4B-A28□
SF4B-F127□ SF4B-H64□ SF4B-A32□
–
SF4B-H72□ SF4B-A36□
–
SF4B-H80□ SF4B-A40□
–
SF4B-H88□ SF4B-A44□
–
SF4B-H96□ SF4B-A48□
70.5
2.776
5 0.197
G
70.5
2.776
H
5
0.197
Emitter
Mounting Total
pitch
length
230
9.055
310
12.205
390
15.354
470
18.504
550
21.654
630
24.803
710
27.953
790
31.102
950
37.402
1,110
43.701
1,270
50.000
1,430
56.299
1,590
62.598
1,750
68.898
1,910
75.197
SF4B-F□
SF4B-A□
SF4B-H□
220
8.661
300
11.811
380
14.960
460
18.110
540
21.260
620
24.409
700
27.559
780
30.708
940
37.007
1,100
43.701
1,260
49.606
1,420
55.905
1,580
62.205
1,740
68.504
1,900
74.803
200
7.874
280
11.024
360
14.173
440
17.323
520
20.472
600
23.622
680
26.772
760
29.921
920
36.220
1,080
42.520
1,240
48.819
1,400
55.118
1,560
61.417
1,720
67.716
1,880
74.016
F
86.6
3.409
Intermediate supporting
bracket mounting pitch
C
270
10.630
350
13.780
430
16.929
510
20.079
590
23.228
670
26.378
750
29.528
830
32.677
990
38.976
1,150
45.276
1,310
51.575
1,470
57.874
1,630
64.173
1,790
70.472
1,950
76.772
286
11.260
366
14.406
446
17.559
526
20.709
606
23.858
686
27.008
766
30.157
846
33.307
1,006
39.606
1,166
45.905
1,326
52.505
1,486
58.504
1,646
64.803
1,806
71.102
1,966
77.401
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
D
STATIC
CONTROL
DEVICES
2
0.079
34.2
1.346
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
Beam
pitch
First beam
channel position
G
H
Model No.
B
SIMPLE
WIRE-SAVING
UNITS
50
1.969
E
Receiver
A’ (Note)
Model No.
SF4B-F31□ SF4B-H16□ SF4B-A8□
34.2
1.346
Display
section
86.6
3.409
Receiver
Protective height
SF4B-F23□ SF4B-H12□ SF4B-A6□
2
0.079
D
19
0.748
5
0.197
Emitter
50
1.969
E
50
1.969
A’A C B
Display
section
F
F
SENSOR
OPTIONS
B C A A’
Display
section
F
50
86.6
3.409 1.969
E
2
0.079
70.5
D
2.776
SENSORS
28
1.102
50
1.969
50
1.969
C B A A’
A’ A B C
INDUCTIVE
PROXIMITY
SENSORS
50 PARTICULAR
1.969 USE
30
1.181
30
28
1.181 1.102
50
1.969
5.5
0.217
1.5
0.059
1.5
0.059
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
D
E
F
-
-
-
SF4B-F□
-
-
-
SF4B-H□
-
-
-
SF4B-A□
-
-
-
-
-
-
-
-
-
-
-
-
SF4B/
SF4B-G
-
-
SF4B-C
-
-
-
-
390
15.354
470
18.504
550
21.654
418
16.457
472
18.583
525
20.669
433
17.047
473
18.622
10
0.394
20
0.787
40
1.575
842
33.150
948
37.323
1,055
41.535
870
1,308
34.252 51.496
950
1,428
37.402 56.220
Note: In the case of “When used as safety device for presses in China”, the distance between the center of the first beam axis and the center of
the last beam axis of the device becomes the protective height (A’). For details, refer to “Definition of sensing heights” (p.645).
5
0.197
5
0.197
15
0.591
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
535
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Safety Light Curtain Type 4
DIMENSIONS (Unit: mm in)
Mounting drawing for the safety light curtains using the dead zoneless mounting brackets MS-SFB-3 (optional) and the
intermediate supporting brackets.
43
1.693
34
1.339
50
1.969
42
1.654
3
15
0.591 0.118
21 0.827
26 1.024
1.5 3 0.118
0.059
SENSOR
OPTIONS
30
1.181
SIMPLE
WIRE-SAVING
UNITS
STATIC
CONTROL
DEVICES
Not available for the robust type SF4B-□G□ Safety light curtain
Assembly dimensions
50 1.969
MEASUREMENT
SENSORS
The CAD data can be downloaded from our website.
SF4B-□
PARTICULAR
USE
SENSORS
WIRE-SAVING
SYSTEMS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
28 1.102
25 0.984
5.5
0.217
5.5
0.217
50
1.969
K J A’ A
Display
section
Display
section
L
19
0.748
LASER
MARKERS
50
1.969
14.5 0.571
38
1.496
K J A A’
L
19
0.748
19
0.748
27
1.063
25
14
0.551 0.984
30 1.181
3 0.118
21 0.827
26 1.024
3 0.118
50
5.5 1.969
0.217
2 0.079
34.2
1.346
50
1.969
Display
section
N
50
1.969
M
86.6
3.409
86.6
3.409
L
70.5
2.776
70.5
2.776
G
50
1.969
43
1.693
A’ A J K
Display
section
50
1.969
M
70.5
2.776
28
1.102
33
1.299
5.5
0.217
1.5
0.059
N
86.6
3.409
L
G
38 H 14.5
1.496 0.571
50
1.969
N
28
1.102
33 1.299
14 0.551
5.5
0.217
1.5
0.059
50
1.969 5.5
0.217
2 0.079
34.2
1.346
50
1.969
A A’ J K
27
1.063
30 1.181
25 0.984
3 0.118
5.5 50 1.969
0.217
2 0.079
19 0.748
5.5 0.217
50
86.6 1.969
3.409 M
70.5
2.776
3
0.118
21 0.827
26 1.024
3 0.118 1.5
0.059
28
1.102
N
50
1.969
43
1.693
50
1.969
43
42
1.693
1.654
34
28 1.102
1.339
15
3
25 0.984
0.118 0.591
21 0.827
26 1.024
14.5
38 H0.571
1.496
19
0.748
14.5 0.571 38
1.496
PLC
Emitter
HUMAN
MACHINE
INTERFACES
Receiver
ENERGY
MANAGEMENT
SOLUTIONS
Protective height
FA
COMPONENTS
A
UV
CURING
SYSTEMS
SF4B-F23□ SF4B-H12□ SF4B-A6□
SF4B-F31□ SF4B-H16□ SF4B-A8□
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B-F39□ SF4B-H20□ SF4B-A10□
SF4B-F47□ SF4B-H24□ SF4B-A12□
SF4B-F55□ SF4B-H28□ SF4B-A14□
SF4B-F63□ SF4B-H32□ SF4B-A16□
SF4B/
SF4B-G
SF4B-F71□ SF4B-H36□ SF4B-A18□
SF4B-C
SF4B-F79□ SF4B-H40□ SF4B-A20□
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
SF4B-F95□ SF4B-H48□ SF4B-A24□
SF4B-F111□ SF4B-H56□ SF4B-A28□
SF4B-F127□ SF4B-H64□ SF4B-A32□
–
SF4B-H72□ SF4B-A36□
–
SF4B-H80□ SF4B-A40□
–
SF4B-H88□ SF4B-A44□
–
SF4B-H96□ SF4B-A48□
MS-SFB-3
Mounting
pitch
Receiver
Intermediate supporting
bracket mounting pitch
A’ (Note)
Model No.
MACHINE
VISION
SYSTEMS
Selection
Guide
Emitter
230
9.055
310
12.205
390
15.354
470
18.504
550
21.654
630
24.803
710
27.953
790
31.102
950
37.402
1,110
43.701
1,270
50.000
1,430
56.299
1,590
62.598
1,750
68.898
1,910
75.197
SF4B-F□
SF4B-A□
SF4B-H□
220
8.661
300
11.811
380
14.960
460
18.110
540
21.260
620
24.409
700
27.559
780
30.708
940
37.007
1,100
43.701
1,260
49.606
1,420
55.905
1,580
62.205
1,740
68.504
1,900
74.803
200
7.874
280
11.024
360
14.173
440
17.323
520
20.472
600
23.622
680
26.772
760
29.921
920
36.220
1,080
42.520
1,240
48.819
1,400
55.118
1,560
61.417
1,720
67.716
1,880
74.016
Beam
pitch
First beam
channel position
G
H
Model No.
J
K
209
8.228
289
11.378
369
14.528
449
17.677
529
20.827
609
23.976
689
27.126
769
30.276
929
36.575
1,089
42.874
1,249
49.173
1,409
55.472
1,569
61.772
1,729
68.071
1,889
74.370
201
7.913
281
11.063
361
14.213
441
17.362
521
20.512
601
23.661
681
26.811
761
29.961
921
36.260
1,081
42.559
1,241
48.858
1,401
55.157
1,561
61.457
1,721
67.756
1,881
74.055
L
M
N
-
-
-
SF4B-F□
-
-
-
SF4B-H□
-
-
-
SF4B-A□
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
370
14.567
450
17.717
530
20.866
398
15.669
452
17.795
505
19.882
413
16.260
453
17.835
10
0.394
20
0.787
40
1.575
822
32.362
928
36.535
1,035
40.748
850
1,288
33.465 50.709
930
1,408
36.614 55.433
Note: In the case of “When used as safety device for presses in China”, the distance between the center of the first beam axis and the center of
the last beam axis of the device becomes the protective height (A’). For details, refer to “Definition of sensing heights” (p.645).
5
0.197
5
0.197
15
0.591
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
536
The CAD data can be downloaded from our website.
SF4B-□G□
It is only available for the robust type SF4B-□G□ Safety light curtain
Assembly dimensions
Mounting drawing for safety light curtains using the standard mounting brackets MS-SF4BG-1 (optional) and the intermediate
supporting brackets.
34.5 1.358
36 1.417
18 0.709
15 0.591
55.5
2.185
42
1.654
4
0.158
55.5
5 2.185
0.197
4
0.158
5 0.197
10
0.394
45
1.772
10
0.394
5.4
5.4
0.213 0.213
6
0.236
6
0.236
5.4
0.213
5.4
0.213 6
6.5
0.256
8
0.315
0.236
G
46
J1.811
F
M
9
0.354
6
0.236
5.4
0.213
H
N
45
1.772
K
6 0.236
A BCDE
46 G
1.811J
46
J1.811
6 0.236
6.5
0.256
8
0.315
5.4
0.213
K
5.4
0.213
5.4
0.213
6 0.236
6 0.236
F
6
0.236
5.4
0.213
M
N
45
1.772
57
2.244
34.5 1.358
36 1.417 36 1.417
18 0.709 18 0.709
15 0.591 15 0.591
57
2.244
4
0.158
55.5 5 0.197
2.185
5.4
45
1.772 0.213
9
0.354
9
0.354
6.5
0.256
8
0.315
B CDE E DCB
A
F
5.5
24
0.217
0.945
Beam
pitch
N
55.5
2.185
42 1.654
55.5
2.185
46
1.811
6 0.236
9
G 0.354
L
6 0.236
6.5
0.256
6 0.236
5.4
0.213
5.4
0.213
8
0.315
F
M
M
6
0.236
6.5
0.256
A
9
0.354 G
L
8 0.315
MICRO
PHOTOELECTRIC
SENSORS
PRESSURE /
FLOW
SENSORS
10
0.394
45
1.772
6.5
0.256
PHOTOELECTRIC
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
34.5 1.358
10
0.394
K
H
H
5.5
5.5
0.217 0.217
Beam
pitch
57
2.244
6 0.236
5.4
0.213
5.4
0.213
6.5
0.256
8
0.315
5.4
0.213
6
0.236
LASER
SENSORS
AREA
SENSORS
57
2.244
4
0.158
5
0.197 55.5
2.185
46
1.811
46
1.811
9
0.354
L L
6.5
0.256
8
0.315
45
1.772
6
0.236
9
9
0.354 0.354
46
1.811
EDCB A
34.5 1.358
36 1.417
18 0.709
15 0.591
42
1.654
FIBER
SENSORS
46
1.811J
5.4
0.213
8
0.315
H
K
N
42 1.654
5.5
0.217
24
0.945
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
Emitter
Receiver
Emitter
Mounting
pitch
Protective height
Model No.
Receiver
Total
length
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
Intermediate supporting
bracket mounting pitch
FA
COMPONENTS
A (Note)
SF4B-F□G
SF4B-A□G
SF4B-H□G□
B
C
D
E
F
G
H
J
K
L
SF4B-F23G SF4B-H12G□ SF4B-A6G
220 8.661
200 7.874
244 9.606 279 10.984 313 12.323 334 13.150
-
-
-
-
-
-
SF4B-F31G SF4B-H16G□ SF4B-A8G
300 11.811
280 11.024
324 12.756 359 14.134 393 15.472 414 16.299
-
-
-
-
-
-
SF4B-F39G SF4B-H20G□ SF4B-A10G
380 14.961
360 14.173
404 15.906 439 17.283 473 18.622 494 19.449
-
-
-
-
-
-
SF4B-F47G SF4B-H24G□ SF4B-A12G
460 18.110
440 17.323
484 19.055 519 20.433 553 21.772 574 22.598
-
-
-
-
-
-
SF4B-F55G SF4B-H28G□ SF4B-A14G
540 21.260
520 20.472
564 22.205 599 23.583 633 24.921 654 25.748
-
-
-
-
-
-
SF4B-F63G SF4B-H32G□ SF4B-A16G
620 24.409
600 23.622
644 25.354 679 26.732 713 28.071 734 28.898
-
-
-
-
-
-
SF4B-F71G SF4B-H36G□ SF4B-A18G
700 27.559
680 26.772
724 28.504 759 29.882 793 31.220 814 32.047
-
-
-
-
-
-
SF4B-F79G SF4B-H40G□ SF4B-A20G
780 30.709
760 29.921
804 31.654 839 33.031 873 34.370 894 35.197 441 17.362
-
414 16.299
-
419 16.496
-
SF4B-F95G SF4B-H48G□ SF4B-A24G
940 37.008
920 36.220
964 37.953 999 39.331 1,033 40.669 1,054 41.496 521 20.512
-
494 19.449
-
499 19.646
-
SF4B-F111G SF4B-H56G□ SF4B-A28G 1,100 43.307 1,080 42.520 1,124 44.252 1,159 45.630 1,193 46.968 1,214 47.795 601 23.661
-
574 22.598
-
579 22.795
-
SF4B-F127G SF4B-H64G□ SF4B-A32G 1,260 49.606 1,240 48.819 1,284 50.551 1,319 51.929 1,353 53.268 1,374 54.094 681 26.811
-
654 25.748
-
659 25.945
-
-
SF4B-H72G□ SF4B-A36G 1,420 55.905 1,400 55.118 1,444 56.850 1,479 58.228 1,513 59.567 1,534 60.394 520 20.472 1,001 39.409 493 19.409 974 38.346 498 19.606 979 38.543
-
SF4B-H80G□ SF4B-A40G 1,580 62.205 1,560 61.417 1,604 63.150 1,639 64.528 1,673 65.866 1,694 66.693 573 22.559 1,108 43.622 546 21.496 1,081 42.559 551 21.693 1,086 42.756
-
SF4B-H88G□ SF4B-A44G 1,740 68.504 1,720 67.716 1,764 69.449 1,799 70.827 1,833 72.165 1,854 72.992 627 24.685 1,215 47.835 600 23.622 1,188 46.772 605 23.819 1,193 46.968
-
SF4B-H96G□ SF4B-A48G 1,900 74.803 1,880 74.016 1,924 75.748 1,959 77.126 1,993 78.464 2,014 79.291 680 26.772 1,321 52.008 653 25.709 1,294 50.945 658 25.906 1,289 50.748
Beam pitch
First beam
channel position
M
N
SF4B-F□G
10 0.394
11.8 0.465
SF4B-H□G□
20 0.787
11.8 0.465
SF4B-A□G
40 1.575
21.8 0.858
Model No.
Note: In the case of “When used as safety device for presses in China”, the distance between the
center of the first beam axis and the center of the last beam axis of the device becomes the
protective height (A). For details, refer to “Definition of sensing heights” (p.645).
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
537
Safety Light Curtain Type 4
DIMENSIONS (Unit: mm in)
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
The CAD data can be downloaded from our website.
SF4B-□G□
It is only available for the robust type SF4B-□G□ Safety light curtain
Assembly dimensions
Mounting drawing for safety light curtains using the dead zoneless mounting brackets MS-SF4BG-3 (optional) and the
intermediate supporting brackets.
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
9
0.354
55.5
2.185
42
1.654
6
0.236
34.5
1.358
55.5
2.185
42
1.654
9
0.354
10.5
0.413
6
0.236 5.4
0.213
6
0.236
PRESSURE /
FLOW
SENSORS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
5.4 0.213
8
0.315
6.5
0.256
PARTICULAR
USE
SENSORS
SIMPLE
WIRE-SAVING
UNITS
9
0.354
C
G
5.4 0.213 C
5.4 0.213
8
0.315
6.5
0.256
6 0.236
J
C
E
5.4 H
0.213
5.4
0.213
D
Beam
pitch
K
5.3 107
0.209 4.213
DEVICES
34.3
1.350
48
1.890
L
34.5
1.358
68.8
2.709
(
6 0.236
6
0.236 J
46
1.811
9
0.354
F 24
0.945
5.4
0.213
K
5.4
0.213 H
5.4
0.213
(
34.3
1.350
5.4
6 0.213
0.236
8
0.315
Q
6
0.236
5.4
0.213
46
1.811
P
6
0.236
6
0.236
5.4
0.213
5.4
0.213
50.5
1.988
5.3 107
0.209 4.213
57
6 5.4
2.244 0.236
0.213
9
103 0.354
4.055
16
0.630
34.5
1.358
68.8
2.709
)
5.4 0.213
5.4 0.213
8
0.315
6.5
0.256
D
L
9
0.354
G
E
A B B A
6
0.236
46
1.811
9
0.354
24
F 0.945
5.4
0.213
5.4
0.213 C
6 5.4
6 0.236
C 0.236 0.213
6
6
0.236 5.4
0.213
0.236
46
1.811 46
1.811
8
0.315
6.5
0.256
6 0.236
6
0.236
46
1.811
9
103
STATIC 4.055 0.354
16
CONTROL
0.630
LASER
MARKERS
55.5
2.185
42
1.654
9 0.354
)
10.5
0.413
6
5.4
0.213 0.236
9
0.354
6
0.236
9 0.354
9
0.354
6.5
0.256 C
E
BA
AB
E
5.4
0.213
8 0.315
6.5
C 0.256
9
0.354 N
9
0.354
9
0.354 103
4.055
5.4
0.213
6
0.236
5.4
T
0.213
6 50.5
0.236 1.988
R
Beam
pitch
D
D
K
9
0.354
K
53
2.087
34.5
1.358
L
68.8 )
(2.709
34.3
1.350
34.3
1.350
L
68.8 )
(2.709
34.3
1.350
U
5.4 6 0.236 C
0.213
6
46
0.236
1.811
S
6.5 0.256
8 0.315
M
50.5
1.988
5.4
0.213
5.4 6 0.236
0.213
6
46
0.236
1.811
6.5
0.256
6.7
0.264
8
0.315
48
1.890
34.5
1.358
8
0.315
6.7
0.264
50.5
1.988
INDUCTIVE
PROXIMITY
SENSORS
SENSOR
OPTIONS
55.5
2.185
42
1.654
8 0.315
6.7
0.264
5.4
0.213
6.7
0.264
48
1.890
8
0.315
PLC
Emitter
HUMAN
MACHINE
INTERFACES
Receiver
ENERGY
MANAGEMENT
SOLUTIONS
Model No.
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Mounting
pitch
Protective height
FA
COMPONENTS
Emitter
Receiver
Intermediate supporting
bracket mounting pitch
A (Note)
SF4B-F□G
SF4B-A□G
SF4B-H□G□
SF4B-F23G SF4B-H12G□ SF4B-A6G
220 8.661
SF4B-F31G SF4B-H16G□ SF4B-A8G
B
C
D
E
F
G
H
J
M
N
P
Q
R
S
T
U
200 7.874
244 9.606
64.5 2.539
-
-
-
-
-
-
-
-
-
-
-
-
-
-
300 11.811
280 11.024
324 12.756
144.5 5.689
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SF4B-F39G SF4B-H20G□ SF4B-A10G 380 14.961
360 14.173
404 15.906
224.5 8.839
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Selection
Guide
SF4B-F47G SF4B-H24G□ SF4B-A12G
460 18.110
440 17.323
484 19.055 304.5 11.988
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Safety Light
Curtains
SF4B-F55G SF4B-H28G□ SF4B-A14G
540 21.260
520 20.472
564 22.205 384.5 15.138
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SF4B-F63G SF4B-H32G□ SF4B-A16G 620 24.409
600 23.622
644 25.354 464.5 18.287
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SF4B-F71G SF4B-H36G□ SF4B-A18G 700 27.559
680 26.772
724 28.504 544.5 21.437
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SF4B-F79G SF4B-H40G□ SF4B-A20G 780 30.709
760 29.921
804 31.654 624.5 24.587 414 16.299
-
333 13.110
-
288 11.339
-
289 11.378
-
330 12.992
-
383 15.079
-
347 13.661
-
SF4B-F95G SF4B-H48G□ SF4B-A24G 940 37.008
920 36.220
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
964 37.953 784.5 30.886 494 19.449
-
413 16.260
-
368 14.488
-
369 14.528
-
410 16.142
-
463 18.228
-
427 16.811
-
SF4B-F111G SF4B-H56G□ SF4B-A28G 1,100 43.307 1,080 42.520 1,124 44.252 944.5 37.185 574 22.598
-
493 19.409
-
448 17.638
-
449 17.677
-
490 19.291
-
543 21.378
-
507 19.961
-
SF4B-F127G SF4B-H64G□ SF4B-A32G 1,260 49.606 1,240 48.819 1,284 50.551 1,104.5 43.484 654 25.748
-
573 22.559
-
528 20.787
-
529 20.827
-
570 22.441
-
623 24.528
-
587 23.110
-
-
SF4B-H72G□ SF4B-A36G 1,420 55.905 1,400 55.118 1,444 56.850 1,264.5 49.783 493 19.409 974 38.346 412 16.220 893 35.157 367 14.449 848 33.386 368 14.488 849 33.425 409 16.102 890 35.039 462 18.189 943 37.126 426 16.772 907 35.709
-
SF4B-H80G□ SF4B-A40G 1,580 62.205 1,560 61.417 1,604 63.150 1,424.5 56.083 546 21.496 1,081 42.559 465 18.307 1,000 39.370 420 16.535 955 37.598 421 16.575 956 37.638 462 18.189 997 39.252 515 20.276 1,050 41.339 479 18.858 1,014 39.921
-
SF4B-H88G□ SF4B-A44G 1,740 68.504 1,720 67.716 1,764 69.449 1,584.5 62.382 600 23.622 1,188 46.772 519 20.433 1,107 43.583 474 18.661 1,062 41.811 475 18.701 1,063 41.850 516 20.315 1,104 43.465 569 22.402 1,157 45.551 533 20.984 1,121 44.134
-
SF4B-H96G□ SF4B-A48G 1,900 74.803 1,880 74.016 1,924 75.748 1,744.5 68.681 653 25.709 1,294 50.945 572 22.520 1,213 47.756 527 20.748 1,168 45.984 528 20.787 1,169 46.024 569 22.402 1,210 47.638 622 24.488 1,263 49.724 586 23.071 1,227 48.307
Model No.
Beam pitch
First beam
channel position
K
L
SF4B-F□G
10 0.394
11.8 0.465
SF4B-H□G□
20 0.787
11.8 0.465
SF4B-A□G
40 1.575
21.8 0.858
Note: In the case of “When used as safety device for presses in China”, the distance between the
center of the first beam axis and the center of the last beam axis of the device becomes the
protective height (A). For details, refer to “Definition of sensing heights” (p.645).
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
SF4B-□
FIBER
SENSORS
Not available for the robust type SF4B-□G□ Safety light curtain
LASER
SENSORS
Protection bar set for rear/side mounting
MC-SFBH-□-T assembly dimensions
PHOTOELECTRIC
SENSORS
Protection bar set MC-SFBH-□ assembly dimensions
538
Rear mounting
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
D
INDUCTIVE
PROXIMITY
SENSORS
A B C
C B A
D
A B C
5
0.197
5
0.197
43.5
1.713
57.5
2.264
43
1.693
43.5
1.713
57.5
2.264
72.7
2.862
72.7
2.862
10
0.394
MC-SFBH-20(-T) SF4B-F39□ SF4B-H20□
MC-SFBH-24(-T) SF4B-F47□ SF4B-H24□
MC-SFBH-28(-T) SF4B-F55□ SF4B-H28□
MC-SFBH-32(-T) SF4B-F63□ SF4B-H32□
MC-SFBH-36(-T) SF4B-F71□ SF4B-H36□
MC-SFBH-40(-T) SF4B-F79□ SF4B-H40□
MC-SFBH-48(-T) SF4B-F95□ SF4B-H48□
MC-SFBH-56(-T) SF4B-F111□ SF4B-H56□
MC-SFBH-64(-T) SF4B-F127□ SF4B-H64□
MC-SFBH-72(-T)
–
SF4B-H72□
MC-SFBH-80(-T)
–
SF4B-H80□
MC-SFBH-88(-T)
–
SF4B-H88□
MC-SFBH-96(-T)
–
SF4B-H96□
60.9
2.398
46.9
1.846
73.7
2.902
44.2
1.740
13 Material: Mounting bracket ···Die-cast zinc alloy 13
Protection bar·········Aluminum
0.512
0.512
Two brackets (one pc. each of R type and L type),
one protection bar
Two pcs. each of M5 (length 16 mm 0.630 in)
hexagon-socket-head bolts, M5 (length 20 mm 0.787 in)
hexagon-socket-head bolt are attached.
MC-SFBH-16(-T) SF4B-F31□ SF4B-H16□
10
0.394
43
1.693
A
B
C
D
279
10.984
359
14.134
439
17.283
519
20.433
599
23.583
679
26.732
759
29.882
839
33.031
999
39.331
1,159
45.630
1,319
51.929
1,479
58.228
1,639
64.527
1,799
70.827
1,959
77.126
296
11.654
376
14.803
456
17.953
536
21.102
616
24.252
696
27.402
776
30.551
856
33.701
1,016
40.000
1,176
46.299
1,336
52.598
1,496
58.898
1,656
65.197
1,816
71.496
1,976
77.795
250
9.843
330
12.992
410
16.142
490
19.291
570
22.441
650
25.591
730
28.740
810
31.890
970
38.189
1,130
44.488
1,290
50.787
1,450
57.087
1,610
63.386
1,770
69.685
1,930
75.984
10
0.394
46.9
1.846
60.9
2.398
10
0.394
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
73.7
2.902
Side mounting
230
9.055
310
SF4B-A8□ 12.205
390
SF4B-A10□ 15.354
470
SF4B-A12□ 18.504
550
SF4B-A14□ 21.654
630
SF4B-A16□ 24.803
710
SF4B-A18□ 27.953
790
SF4B-A20□ 31.102
950
SF4B-A24□ 37.402
1,110
SF4B-A28□ 43.701
1,270
SF4B-A32□ 50.000
1,430
SF4B-A36□ 56.299
1,590
SF4B-A40□ 62.598
1,750
SF4B-A44□ 68.898
1,910
SF4B-A48□ 75.197
MC-SFBH-12(-T) SF4B-F23□ SF4B-H12□ SF4B-A6□
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
10
0.394 10
0.394
Model No. Applicable safety light curtain model No.
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
5
0.197
10
0.394
10
0.394
D
44.2
1.740
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
C B A
D
5
0.197
D
A B C
Selection
Guide
5
0.197
Safety Light
Curtains
Safety
Control Units
E
27.7
1.091
F
27.7
1.091
73.7
2.902
73.7
2.902
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
View E
10
0.394
10
0.394
SF4C
View F
BSF4-AH80
SF2B
46.9
1.846
10
0.394
10
0.394
46.9
1.846
61.9
61.9
2.437
2.437
Material: Mounting bracket ···Cold rolled carbon steel (SPCC)
(Trivalent chrome plated)
Protection bar·········Aluminum
Two brackets (one pc. each of R type and L type),
one protection bar
Two pcs. each of M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts, M5 (length 20 mm 0.787 in)
hexagon-socket-head bolt are attached.
SF2C
Definition of
Sensing Heights
539
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
Safety Light Curtain Type 4
DIMENSIONS (Unit: mm in)
RF-SFBH-□
Corner mirror (Optional)
17.5
6
0.689 0.236
18 0.709
6 0.236
t3
t 0.118
29
1.142
t 3 t 0.118
13
26
1.024 0.512
80
3.150
Effective
reflective
surface
29
1.142
ABC
INDUCTIVE
PROXIMITY
SENSORS
106
4.173
64
2.520
MEASUREMENT
SENSORS
8 0.315
)
-
-
-
-
-
-
-
-
-
-
-
458 ±50
18.031 ±1.969
538 ±50
21.181 ±1.969
618 ±50
24.331 ±1.969
698 ±50
27.480 ±1.969
538 ±50
21.181 ±1.969
591 ±50
23.268 ±1.969
645 ±50
25.394 ±1.969
698 ±50
27.480 ±1.969
-
RF-SFBH-64
Standard mounting bracket (Optional)
RF-SFBH-72
RF-SFBH-80
RF-SFBH-88
RF-SFBH-96
MS-SFB-1-T
Safety
Control Units
30°
3
33
1.299 0.118
14
0.551
28
1.102
10
0.394
5.5 0.217
28
1.102
R8.5 R0.335
M5 (length
6 0.236)
60°
3 0.118
6.2
0.244
10.8
0.425
6.1
0.240
8.7
0.343
M5
8.1
0.319
11
0.433
9.6
0.378
Four bracket set
Four M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts are attached.
MS-SF4BG-1
BSF4-AH80
10
0.394
SF2B
34.5
1.358
17.5
0.689
15
0.591
Standard L mounting bracket (Optional)
It is only available for the
robust type SF4B-□G□.
5 0.197
5.5 0.217
18
36
0.709 1.417
40°
2
0.079
55.5
2.185
ø9.8
ø0.386
34.5
1.358
45
1.772
Material: SPHC
Four bracket set
Eight M5 (length: 10
mm 0.394 in)
hexagon-socket-head
40°
bolts are attached.
ø25
ø0.984
5.2
0.205
30°
24.5
0.965
R16.6
R0.654
10
0.394
R8.5 R0.335
M5 (length
6 0.236)
10.8
0.425
15
0.591
M5 (length
14 0.551)
28
27.4 1.102
1.079
R18.4
R0.724
Material: Die-cast zinc alloy
SF4D
R
R
4-R2.8 R0.110
28
1.102
Safety
Components
SF4C
1,018 ±50
40.079 ±1.969
1,125 ±50
44.291 ±1.969
1,231 ±50
48.464 ±1.969
1,338 ±50
52.677 ±1.969
8.4 0.331
15 0.591
R16.6 R0.654
-
M8 mounting bracket (Optional)
R4.1 R0.161 (for sensor mounting)
8.2
5 0.197
0.323
5.5 0.217
18
0.709
28
1.102
Safety Light
Curtains
-
8 0.315
24.5
0.965
60°
-
Not available for the robust type SF4B-□G□
8.4 0.331
3
0.118
R18.4 R0.724
Definition of
Sensing Heights
-
970 g
approx.
1,170 g
approx.
1,370 g
approx.
1,570 g
approx.
1,770 g
approx.
1,970 g
approx.
2,170 g
approx.
2,660 g
approx.
3,060 g
approx.
3,460 g
approx.
3,890 g
approx.
4,550 g
approx.
4,950 g
approx.
5,350 g
approx.
5,750 g
approx.
RF-SFBH-56
< When mounting at an angle of 45° >
M5 (length
14 0.551)
SF2C
RF-SFBH-12
RF-SFBH-48
104 )
(4.094
20 15
28 0.787 0.591
1.102
UV
CURING
SYSTEMS
SF4B-C
Net weight
272
10.709
352
13.858
432
17.008
512
20.157
592
23.307
672
26.457
752
29.606
832
32.756
992
39.055
1,152
45.354
1,312
51.653
1,472
57.953
1,632
64.252
1,792
70.551
1,952
76.850
Not available for the robust type SF4B-□G□
MACHINE
VISION
SYSTEMS
SF4B/
SF4B-G
F
-
RF-SFBH-40
(
72 2.835
46
28
1.811
1.102
FA
COMPONENTS
Selection
Guide
E
-
RF-SFBH-36
E
45°
PLC
ENERGY
MANAGEMENT
SOLUTIONS
D
298
11.732
378
14.882
458
18.031
538
21.181
618
24.331
698
27.480
778
30.630
858
33.779
1,018
40.079
1,178
46.378
1,338
52.677
1,498
58.976
1,658
65.275
1,818
71.575
1,978
77.874
RF-SFBH-32
46
1.811
MS-SFB-1
C
246
9.685
326
12.835
406
15.984
486
19.134
566
22.283
646
25.433
726
28.583
806
31.732
966
38.031
1,126
44.331
1,286
50.630
1,446
56.929
1,606
63.228
1,766
69.527
1,926
75.827
RF-SFBH-28
F
109 )
(4.219
STATIC
CONTROL
DEVICES
HUMAN
MACHINE
INTERFACES
18
0.709
6
0.236
ø8.5
ø0.335
WIRE-SAVING
SYSTEMS
B
236
9.291
316
12.441
396
15.591
476
18.740
556
21.890
636
25.039
716
28.189
796
31.339
956
37.638
1,116
43.937
1,276
50.236
1,436
56.535
1,596
62.835
1,756
69.134
1,916
75.433
RF-SFBH-24
ø8.5
ø0.335
D
SIMPLE
WIRE-SAVING
UNITS
A
RF-SFBH-20
26
13
1.024 0.512
SENSOR
OPTIONS
Model No.
RF-SFBH-16
17.5
6
0.689 0.236
PARTICULAR
USE
SENSORS
LASER
MARKERS
The CAD data can be downloaded from our website.
14
0.551
28
1.102
3
0.118
6.2
0.244
6.1
8.7 0.240
0.343
29
1.142
M5
11
0.433
Material: Die-cast zinc alloy
Four bracket set
Four M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts are attached.
8.1
0.319
9.6
0.378
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
MS-SFB-2
The CAD data can be downloaded from our website.
Not available for the robust type SF4B-□G□ Intermediate supporting bracket (Accessory for safety light curtain)
12
0.472
4-R2.8
0.110
55
(2.165
)
2
0.079
43
1.693
15
0.591
9
0.354
24.8
0.976 14.8
0.583
5.5
0.217
5.5 0.217
33 1.299
50 1.969
60 2.362
32
1.260
8.8
0.346
13 0.512
8.3 0.327
2 0.079
R21.4 R0.843
30°
31
28
(1.220
) (1.102
)
12.5
0.492
2
0.079
5.5
5.5
0.217 0.217
50 1.969
Material: Die-cast zinc alloy
MS-SF4BG-2
AREA
SENSORS
22.2
0.874
4-R2.8
R0.110
2 0.079
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
8.5
0.335
PRESSURE /
FLOW
SENSORS
52
2.047 41
1.614
13
0.512
10.5
0.413
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
Note: T
he intermediate supporting bracket (MS-SFB-2) is enclosed
with the following products. The quantity differs depending on
the product as shown below:
1 set: S
F4B-F□ … 79 to 111 beam channels
SF4B-H□ … 40 to 56 beam channels
SF4B-A□ … 20 to 28 beam channels
2 sets: S
F4B-F127□
SF4B-H□ … 64 to 80 beam channels
SF4B-A□ … 32 to 40 beam channels
3 sets: S
F4B-H□ … 88 to 96 beam channels
SF4B-A□ … 44 to 48 beam channels
It is only available for the robust type SF4B-□G□ Intermediate supporting bracket (Accessory for safety light curtain)
Rear mounting
5.4
0.213
23
0.906
9
10 0.354
0.394
8
0.315
23
0.906
26.5
1.043
10
0.394
43 (46.1)
34.5 1.693 (1.815)
1.358
34.5
1.358
43
1.693
(51.5)
(2.028)
8
0.315
9
10 0.354
0.394
5.4
0.213
10.5
0.413
ø5.4 ø0.213
mounting hole
9
0.354
18
0.709
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
HUMAN
MACHINE
INTERFACES
18
0.709 8
0.315
5.4
0.213
56
8
2.205
0.315 32
1.260
SENSOR
OPTIONS
PLC
Side mounting
18
0.709
LASER
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
M4
(length
12 0.472)
40 1.575
37 1.457
FIBER
SENSORS
PHOTOELECTRIC
SENSORS
9.5
0.374
5.8
0.228
ø5.4 ø0.213
mounting hole
540
9
0.354
10
0.394
26.5
1.043
ENERGY
MANAGEMENT
SOLUTIONS
56
2.205
32
1.260
5.4
0.213
10.5
0.413
(51.5)
43
34.5 1.693 (2.028)
1.358
18
0.709
34.5
1.358
43
1.693
(46.1)
(1.815)
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
Material: C
old rolled carbon steel
(SPCC)
Supporting bracket ··· PPS
SF4D
SF4B/
SF4B-G
SF4B-C
Note: T
he intermediate supporting bracket MS-SF4BG-2 is enclosed
with the following products. The quantity differs depending on
the product as shown below:
1 set: S
F4B-F□G … 79 to 127 beam channels
SF4B-H□G□ … 40 to 64 beam channels
SF4B-A□G … 20 to 32 beam channels
2 sets: S
F4B-H□G□ … 72 to 96 beam channels
SF4B-A□G … 36 to 48 beam channels
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights
541
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
MS-SFB-3
The CAD data can be downloaded from our website.
Not available for the robust type SF4B-□G□ Dead zoneless mounting bracket (Optional)
Main body
MICRO
PHOTOELECTRIC
SENSORS
4-R4
6.8 R0.157
0.268
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
9.5 0.374
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
26
1.024 17.3 13
0.681 0.512
Four bracket set
Four M5 (length 25 mm 0.984 in)
hexagon-socket-head
bolts and four spacers are attached.
55 2.165
9
5 0.354
0.197
STATIC
CONTROL
DEVICES
34 1.339
2 0.079
8.5 0.335
11.6 0.457
12 0.472
2-M5
12
0.472
20 0.787
59.5 2.343
2-R3 R0.118
8.4 0.331
9.5
0.374
R3
R0.118
8.4
0.331
ø5.5 ø0.217
Mounting adjustment range
20 0.787 (Note)
15° 15°
The adjustment
range of the safety
light curtain angle is
up to ±15 degrees.
26
1.024
PLC
3
0.118
26
1.024
Spacer
3
21 0.118
0.827
LASER
MARKERS
5.5
0.217
3
0.118
3-R1 R0.039
9
4.5
0.354 0.177
L-shaped mounting
5.5
0.217
5.5
0.217
M4
(length
10 0.394)
39 1.535
51 2.008
59.5 2.343
68 2.677
PARTICULAR
USE
SENSORS
Material: Die-cast zinc alloy
26
1.024
38
1.496
4 0.157
INDUCTIVE
PROXIMITY
SENSORS
SIMPLE
WIRE-SAVING
UNITS
5.5
0.217
2-M5
19
0.748 15 10.8
50 41.2 25
0.591 0.425
1.969 1.622 0.984
PRESSURE /
FLOW
SENSORS
SENSOR
OPTIONS
2-R4 4-R2.8
R0.157 R0.110
2-R3.3
R0.130
23
0.906
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
38 1.496
50 1.969
17 0.669
Note: T
he finger protection type has a beam pitch of 10 mm 0.394 in, which produces a dead
zone. Additional measures will be required, such as using a protection cover.
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
MS-SF4BG-3
Main body
Dead zoneless mounting bracket (Optional)
5.4
0.213
Selection
Guide
68.8 2.709
58.5 2.303
42.5 1.673
34.5 1.358
26.5 1.043
25
0.984
Safety
Control Units
8 0.315
10.5
0.413
5.4
0.213
SF4B/
SF4B-G
SF4B-C
SF4C
9 0.354
9.5 0.374
SF2C
Definition of
Sensing Heights
18
69
7 0.709
2.717
0.276
45.5
1.791
(Sliding range)
Material: Die-cast zinc alloy
t 3.2
t 0.126
10.5
0.413
5.4
0.213
20°
18
0.709
28
1.102
20°
10°
10°
10.5
0.413
40°
60°
Material: Dead zoneless mounting bracket ··· Cold rolled carbon steel (SPCC)
(Trivalent chrome plated)
Dead zoneless supporting bracket ··· PPS
Mounting adjustment range
The adjustment
range of the safety
light curtain angle is
up to ±10 degrees.
10
0.394
60°
18.1
0.713
8 0.315
52.5 2.067
5.5
0.217
ø5.4 ø0.213
62.6 2.465
66.7 2.626
60.5 2.382
50.7 1.996
5.4
0.213
43.2
1.701
26.5
1.043
BSF4-AH80
SF2B
3
0.118
63.5
2.500
74.5
2.933
85.5
3.366
26
1.024 13
0.512
Safety
Components
Pitch adapter bracket (Optional)
Not available for the robust type SF4B-□G□
8.4
0.331
Safety Light
Curtains
SF4D
MS-SFB-4
It is only available for the robust type SF4B-□G□.
10° 10°
hexagon-socket-head bolts
[M5 (length 8 mm 0.315 in)]
34.5
1.358
30°
R8.5 R0.335
M5 (length
6 0.236)
15
0.591
M5 (length
14 0.551)
R18.4 R0.724
R16.6 R0.654
4-R2.8 R0.110
Four bracket set
Four M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts are
attached.
6.1
10.8 0.240
0.425
6.2
0.244
28
1.102
14
0.551
28
1.102
8.1
0.319
8.7
0.343
4.7
0.185
M5
11
0.433
9.6
0.378
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
MS-SFB-4-T
Not available for the robust type SF4B-□G□ M8 pitch adapter bracket (Optional)
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
8.4
0.331
8 0.315
MICRO
PHOTOELECTRIC
SENSORS
3
0.118
63.5
78 2.500
3.071
85.5
3.366
542
AREA
SENSORS
18
69
7 0.709
2.717
45.5
0.276
1.791
(Sliding range)
10
0.394
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
Material: Die-cast zinc alloy
10
0.394
28
1.102
60°
30°
15
0.591
R18.4 R0.724
28
1.102
14
0.551
28
1.102
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
R8.5 R0.335
M5 (length
6 0.236)
M5 (length
14 0.551)
R16.6 R0.654
Four bracket set
Four M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts are attached.
2-R5 R0.197
10.8
0.425
SIMPLE
WIRE-SAVING
UNITS
6.1
0.240
8.7
0.343
4.7
0.185
SENSOR
OPTIONS
6.2
0.244
11
0.433
M5
8.1
0.319
9.6
0.378
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
MS-SFB-7-T MS-SFB-1-T2 (Rear mounting)
M8 rear mounting bracket (Optional) M8 rear/side mounting brackets set (Optional)
Not available for the robust type SF4B-□G□
8.5
0.335
PLC
2-R5
R0.197
40.6
(1.598
)
Mounting adjustment range
25.25
0.994
15°
10
10
0.394 0.394
27.2
1.071
7.6
0.299
M5 (length
10 0.394)
LASER
MARKERS
(
)
26
1.024
28
1.102
8
0.315
2.3
0.091
29
1.142
15°
17
0.669
The adjustment
range of the safety
light curtain angle is
up to ±15 degrees.
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
28
(1.811
)
R20.2
(R0.795
)
M5
HUMAN
MACHINE
INTERFACES
UV
CURING
SYSTEMS
Material: Cold rolled carbon steel (SPCC) (Trivalent chrome plated)
Four bracket set
Four M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts are attached.
Selection
Guide
Safety Light
Curtains
MS-SFB-8-T MS-SFB-1-T2 (Side mounting)
4 0.157
Not available for the robust type SF4B-□G□
Safety
Components
10.75
0.423
8
0.315
10
0.394
)
29
40.6
1.598 1.142
10
7.6 0.394
0.299
(
Safety
Control Units
10.75
0.423
8
0.315
M5
(
M8 side mounting bracket (Optional) M8 rear/side mounting brackets set (Optional)
2-R5 R0.197
(
28.35
1.116
)
14.75
0.581
M5 (length
10 0.394)
)
33.5
1.319
28
1.811
2.3
0.091
10
0.394
(
10
0.394
(
)
(
15°
)
14.75
0.581
M5 (length
10 0.394)
33.5
1.319
2.3
0.091
28
1.811
15°
The adjustment
range of the safety
light curtain angle is
up to ±15 degrees.
7.6
0.299
)
SF4D
SF4B/
SF4B-G
29
40.6
1.142 1.598
2-R5 R0.197
28.35
1.116
Mounting adjustment range
M5
4 0.157
R20.2
(R0.795
)
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
28
(1.811
)
Material: Cold ralled carbon steel (SPCC)
(Trivalent chrome plated)
Four bracket
(two pcs. each of R type and L type) set
Four M5 (length 18 mm 0.709 in)
hexagon-socket-head bolts are attached.
Definition of
Sensing Heights
543
FIBER
SENSORS
LASER
SENSORS
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
SF-C11
The CAD data can be downloaded from our website.
Control unit (Optional)
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
54.1
2.130
AREA
SENSORS
4
0.157
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
13
0.512
40
1.575
25
0.984
35
1.378
67.3
2.650
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
48.8
1.921
6.5
0.256
80
3.150
100
3.937
(
11.5
0.453
Receiver
side
connector
130
5.118
28
114
1.102
4.488 8
0.315
67.5
2.657
6.5
0.256
81.4
135 3.205
(5.315
)
6
19.5 0.236
0.768
22 24.5 30.5
0.866 0.965 1.201
)
36.5
1.437
36.5 34.2
1.437 1.346
Suitable for 35 mm 1.378 in width DIN rail
SF-C13
21
0.827
8 0.315
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
127
5.000
80
3.150
30
1.181
2-ø6 ø0.236
2-ø10 ø0.394
6
7 0.276 0.236
6
0.236
10
0.394
SIMPLE
WIRE-SAVING
UNITS
Control unit (Optional)
Emitter side
connector
3 × 6 = 18
3 × 0.236 = 0.709
130
5.118
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
46
1.811
23
0.906
SF-C12
Control unit (Optional)
SF-C14EX(-01)
Application expansion unit (Optional)
STATIC
CONTROL
DEVICES
LASER
MARKERS
6.75
0.266
4
0.157
PLC
4 0.157
3 × 5 = 15
3 × 0.197 = 0.591
130
5.118
ENERGY
MANAGEMENT
SOLUTIONS
6
0.236
34.5
1.358
35
1.378
67.3
2.650
HUMAN
MACHINE
INTERFACES
5
0.197
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
10
0.394
13.5
0.531
6.5
0.256
80
3.150
80.8
3.181
13
0.512
22.5
0.886
SFB-HC
5
0.197
10
0.394
Handy-controller (Optional)
80
3.150
99
3.898
Suitable for 35 mm 1.378 in width DIN rail
25.4
1.000
ø6 ø0.236 cables,
0.5 m 1.640 ft long
(
)
Y-shaped connector (Optional)
ø9
ø0.354
FUNCTION
SF2B
140
5.512
SF2C
CANCEL
ENTER
66 2.598
22.5
0.886
13.5
0.531
SF4C
Definition of
Sensing Heights
6.5
0.256
SFB-WY1
SF4B-C
BSF4-AH80
11
0.433
65 2.559
30
1.181
23
0.906
Receiver
side
connector
31.1
1.224
13
0.512
67.3
2.650
Suitable for 35 mm 1.378 in width DIN rail
Safety
Components
SF4B/
SF4B-G
25
34.1
0.984 1.343
130
5.118
Safety
Control Units
SF4D
Emitter side
connector
35
1.378
91.6
3.606
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
54.1
2.130
40
1.575
46
1.811
38.4 1.512
18 18.4
0.709 0.724
23 0.906
41
1.614
ø14 45.8 31
ø0.551 1.803 1.220
Safety Light Curtain Type 4
SF4B SERIES Ver.2 SF4B-G SERIES Ver.2
DIMENSIONS (Unit: mm in)
SF-LAT-2N
The CAD data can be downloaded from our website.
Laser alignment tool (Optional)
Not available for the robust type SF4B-□G□
SF-LAT-4BG
Laser alignment tool (Optional)
It is only available for the robust type SF4B-□G□.
21
22.2
(0.827
) 0.874
ø12
ø0.472
66.5
2.618
Center of beam axis
(21)
22
(0.827) 0.866
18.75
0.738
48
1.890
28
1.102
38
1.496
28
1.102
544
Center of beam axis
5.3
0.209
31
1.220
ø12
ø0.472
66.5
2.618
1 0.039
15.8
0.622
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
28
1.102
20
0.787
48
1.890
92
3.622
20
0.787
62
2.441
92
3.622
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
SF-IND-2
Large display unit for safety light curtain (Optional)
MEASUREMENT
SENSORS
22.8
0.898
18.3
0.720
STATIC
CONTROL
DEVICES
25
0.984
35.5
40.1 1.398 23
1.579
0.906
4.6
0.181
WIRE-SAVING
SYSTEMS
LASER
MARKERS
PLC
18
0.709
28
1.102
5.5 0.217
ø3.6 ø0.142 cable,
3m 9.843 ft long
25.4
1.000
t 1.6 t 0.063
6.6 0.260
10.4 0.409
Material: Bracket ··· C
old rolled carbon steel
(SPCC)(Black chromate)
Enclosure ··· POM
Cover ··· Polycarbonate
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Safety Light
Curtains
Safety
Control Units
Safety
Components
SF4D
SF4B/
SF4B-G
SF4B-C
SF4C
BSF4-AH80
SF2B
SF2C
Definition of
Sensing Heights