MS-PE-1

751 FIBER SENSORS Micro-differential Pressure High-precision Digital Pressure Sensor DP-M SERIES Related Information ■ General terms and conditions............. F-7 ■ Glossary of terms ........................ P.1469~ For Gas ■ Sensor selection guide ................. P.731~ ■ General precautions ...................... P.1472 LASER SENSORS PHOTOELECTRIC SENSORS Conforming to EMC Directive MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS panasonic.net/id/pidsx/global With analog output Digital STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DP-100 DP-M High accuracy & resolution High accuracy and resolution Due to differential pressure sensing, the pressure can be set with a high resolution of 0.01 kPa.D {1 mmH2O.D} over a pressure range of 0 to 2.00 kPa.D {0 to 204 mmH2O.D} and, moreover, the detection accuracy is within ±1 % F.S. Setting resolution 0.01 kPa.D {1 mmH2O.D} Detecting clogging of filter The clogging of a filter can be reliably detected by the differential pressure, indicating the time for filter replacement. Repeatability Within ±1 % F.S. Lo Hi MODE FUNCTIONS Bright display and easy key operation Versatile control with two output modes Three bright red 7-segment LEDs, 12 mm 0.472 in high, are incorporated in the compact body. They can be clearly read not only in a dark place, but also, in a welllit place. Further, initialization or pressure settings can be easily done with key operation while looking at the display. 1 Hysteresis mode The lower threshold value and the upper threshold value establish the hysteresis of the comparative output. Pressure unit selectable The pressure unit can be selected from “kPa” and “mmH2O” according to your requirement. Further, during measurement, the pressure unit can be recognized at a glance from the pressure unit indicator. kPa mmH2O When the pressure unit is changed, threshold values and the measured pressure value are automatically converted. 2 Window comparator mode The comparative outputs can be made ON or OFF by a pressure within the limits set by the upper and the lower threshold levels. VARIETIES Analog current output type: DP-M2A DP-M2A is incorporated also with the analog current output (4 to 20 mA). Hence, it is ideally suited for real time monitoring and multi-point control in combination with an analog controller (ultra-compact digital panel controller CA2 series). Micro-differential Pressure High-precision Digital Pressure Sensor DP-M SERIES ORDER GUIDE 752 FIBER SENSORS LASER SENSORS Appearance Rated pressure range Model No. Standard Type Pressure port Output MICRO PHOTOELECTRIC SENSORS DP-M2 With analog current output AREA SENSORS ø4.6 mm ø0.181 in resin pipe 0 to 2.00 kPa.D {0 to 204 mmH2O.D} PHOTOELECTRIC SENSORS NPN open-collector transistor DP-M2A LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS OPTIONS Designation SENSOR OPTIONS Model No. Description Sensor mounting bracket MS-PE-1 L-shaped bracket [Two M3 (length 8 mm 0.315 in) screws with washers are attached.] Panel mounting bracket MS-PE-2 It can be used for mounting on a panel (1 to 3.2 mm 0.039 to 0.126 in thick). Front protection cover MS-PE-3 It protects the sensor’s adjustment panel. (It can be fitted when the panel mounting bracket is used.) CA2-T1 This is a very small controller which allows two independent threshold level settings. • Supply voltage: 24 V DC ±10 % • No. of inputs: 1 No. (sensor input) • Input range: 4 to 20 mA • Output: NPN open-collector transistor • Main functions: Threshold level setting function, zero-adjust function, scale setting function, hysteresis setting function, start / hold function, auto-reference function, power supply ON-delay function, etc. Digital panel controller (Note) Note: Refer to p.1143~ for details of the ultra-compact digital panel controller CA2 series. Sensor mounting bracket • MS-PE-1 H Panel mounting bracket Front protection cover Front protection cover MS-PE-3 WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS Digital panel controller • CA2 series • MS-PE-2 • MS-PE-3 Lo SIMPLE WIRE-SAVING UNITS MACHINE VISION SYSTEMS UV CURING SYSTEMS M1 DP M2 -M 2 OU T i mmH 2O kPa 0-A DJ MO DE Two M3 (length 8 mm 0.315 in) screws with washers are attached. ( Panel mounting bracket MS-PE-2 Suitable for 1 to 3.2 mm 0.039 to 0.126 in thick panel Selection Guide ) Pressure/ Digital Display Pressure/ Head-separated Flow DP-100 DP-M 753 Micro-differential Pressure High-precision Digital Pressure Sensor SPECIFICATIONS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS DP-M SERIES Type Item Model No. Standard type With analog current output type DP-M2 DP-M2A Type of pressure Differential pressure Rated pressure range 0 to 2.00 kPa.D {0 to 204 mmH2O.D} Set pressure range 0 to 2.00 kPa.D {0 to 204 mmH2O.D} Set pressure resolution 0.01 kPa.D {1 mmH2O.D} Pressure withstandability 6 kPa.D {612 mmH2O.D} Applicable fluid Non-corrosive gas Selectable units kPa, mmH2O +10 12 to 24 V DC –15 % Supply voltage Current consumption Comparative output SIMPLE WIRE-SAVING UNITS Output operation MEASUREMENT SENSORS DC-12 or DC-13 Selectable either normally open (NO) or normally closed (NC) by the key Hysteresis STATIC ELECTRICITY PREVENTION DEVICES 0.01 kPa.D {1 mmH2O.D} Repeatability LASER MARKERS 75 mA or less NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between comparative output and 0 V) • Residual voltage: 1 V or less (at 100 mA sink current) 0.4 V or less (at 16 mA sink current) Utilization category WIRE-SAVING SYSTEMS Within ±1 % F.S. Response time 10 ms or less Short-circuit protection Incorporated Output current: 4 to 20 mA (from 0 to 1.96 kPa.D {0 to 200 mmH2O.D}) Zero-point: within 4 mA ± 1 % F.S. Span: within 16 mA ± 3 % F.S. Linearity: within ±1 % F.S. Load resistance: 0 to 250 Ω PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Analog current output Display Displayable pressure range FA COMPONENTS UV CURING SYSTEMS Operation Indicators MACHINE VISION SYSTEMS Pressure unit Pressure/ Head-separated Flow DP-100 DP-M Environmental resistance Pressure/ Digital Display – 3 digit red LED display (Sampling rate: 4 times/sec. approx.) –0.05 to 2.10 kPa.D {–5 to 210 mmH2O.D} Orange LED (lights up when the comparative output is ON) Red LED (The indicator corresponding to the selected unit lights up during the sensing mode.) M1 setting Red LED (blinks in the M1 setting mode) M2 setting Red LED (blinks in the M2 setting mode) Pollution degree Selection Guide Ripple P-P 10 % or less 50 mA or less Ambient temperature Ambient humidity EMC Voltage withstandability 3 (Industrial environment) 0 to +50 °C +32 to +122 °F (No dew condensation), Storage: –10 to +60 °C +14 to +140 °F 35 to 85 % RH, Storage: 35 to 85 % RH EN 61000-6-2, EN 61000-6-4 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each Shock resistance 100 m/s2 acceleration (10 G approx.) in X, Y and Z directions for three times each Temperature characteristics Over ambient temperature range 0 to +50 °C +32 to +122 °F: within ±3 % F.S. of detected pressure at +25 °C +77 °F Pressure port Material Cable Cable extension Weight ø4.6 mm ø0.181 in resin pipe Front case: ABS, Rear case: ABS, LED display: Acrylic, Pressure port: PA 0.18 mm2 3-core oil resistant cabtyre cable, 2 m 6.562 ft long 0.18 mm2 4-core oil resistant cabtyre cable, 2 m 6.562 ft long Extension up to total 100 m 328.084 ft (less than 10 m 32.808 ft when conforming to CE marking) is possible with 0.3 mm2, or more, cable. Net weight: 75 g approx., Gross weight: 135 g approx. Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. Micro-differential Pressure High-precision Digital Pressure Sensor DP-M SERIES 754 I/O CIRCUIT AND WIRING DIAGRAMS I/O circuit diagram FIBER SENSORS LASER SENSORS Wiring diagram PHOTOELECTRIC SENSORS Color code Sensor circuit D Tr M1 Comparative Load (Black) output M2 + 100 mA max. (White) Analog current output (Note) – ZD1 ZD2 Internal circuit (Brown) +V 4 to 20 mA (Blue) 0 V 12 to 24 V DC +10 –15 % Load 0 to 250 Ω MICRO PHOTOELECTRIC SENSORS OUT AREA SENSORS kPa MODE LIGHT CURTAINS / SAFETY COMPONENTS 0-ADJ PRESSURE / FLOW SENSORS Brown Users’ circuit Note: The analog current output is equipped only with the DP-M2A. The analog current output of DP-M2A does not incorporate a shortcircuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Load Black + 12 to 24 V DC +10 –15 % Load 0 to 250 Ω Blue Symbols … D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr: NPN output transistor – White (Note) Note: The white lead wire is equipped only with the DP-M2A. PRECAUTIONS FOR PROPER USE Refer to p.1472 for general precautions. • Never use this product as a sensing device for personnel protection. • In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. • The DP-M series is designed for use with non-corrosive gas. It cannot be used for liquid or corrosive gas. Mounting • The displayed value may vary by 1 digit (0.01 kPa.D {1 mmH2O.D}) maximum depending on whether the sensor is installed vertically or horizontally. • A sensor mounting bracket MS-PE-1 (optional) may be used. When mounting the sensor with the sensor mounting M3 (length 8 mm 0.315 in) screw with washers bracket, the (Accessory for MS-PE-1) tightening torque should be mounting bracket 0.5 N·m or Sensor MS-PE-1 (Optional) less. Operation • If setting is impossible even with pressing the MODE key, verify whether the key-protect function is enabled. Please note that pressing down on the MODE key for an extended moment (for 4 sec. or more) will enable the key-protect function as soon as the key is released. The key-protect function is set when the display shows and is released when the display shows . • If using the window comparator mode, lower threshold value (M1) and upper threshold value (M2) should be set with a difference of 3 digits (0.03 kPa.D {3 mmH2O.D}) or more. No output will be possible with a 0 to 2 digits difference. INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS Piping • Apply higher pressure to the Hi-port and lower pressure to the Lo-port. MACHINE VISION SYSTEMS UV CURING SYSTEMS • Use flexible tubes (silicone tube etc.) that can fit the pressure ports, ø4.6 mm ø0.181 in in diameter. The tubes should cover more than half the length of the pressure ports. Lo H i Recommended tube Selection Guide • TYGON® tube R-3603, size: internal dia 4 mm 0.157 in, external dia 6 mm 0.236 in, manufactured by Saint-Gobain K. K. Contact the manufacturer for details of the recommended product. Pressure/ Digital Display Flow Pressure Lo-port Flexible tube (Silicone tube etc.) Conditions in use for CE conformity • The DP-M series is a CE conformity product complying with EMC Directive. The harmonized standard with regard to immunity that applies to this product is EN 61000-6-2 and the following condition must be met to conform to that standard. Conditions • The sensor should be connected less than 10 m 32.808 ft from the power supply. • The signal line to connect with this sensor should be less than 30 m 98.425 ft. Pressure/ Head-separated DP-100 Pressure Hi-port Fix tubes on ports securely Notes: 1) TYGON is registered trademarks of Saint-Gobain K. K. 2) Ensure that excessive pressure is not applied to the pressure ports. Since this sensor is designed for detecting small pressures, if excessive pressure or shock is applied to the pressure ports, the diaphragm (pressure sensing device) in the sensor may get damaged. 3) Please do not compress the tube. If the tube is compressed, pressure exceeding the rated value may be generated, damaging the diaphragm (pressure sensing device). Not good DP-M 755 Micro-differential Pressure High-precision Digital Pressure Sensor PRECAUTIONS FOR PROPER USE FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS Wiring 5 5 2 0 Window comparator mode ( 4 SIMPLE WIRE-SAVING UNITS 6 WIRE-SAVING SYSTEMS 7 10 Description 1 3 digit LED display (Red) Comparative ON output when set to NO OFF Function 2 M1 setting indicator (Red) Blinks in the lower threshold value (M1) setting mode. PLC 3 M2 setting indicator (Red) Blinks in the upper threshold value (M2) setting mode. HUMAN MACHINE INTERFACES 4 Operation indicator (Orange) Lights up when the comparative output is ON. 5 Pressure unit indicator (mmH2O, kPa) (Red) • The indicator of the selected unit lights up during the sensing mode. • Both indicators light off during the initial setting mode and during an error occurrence. • The indicator of the selected unit blinks during the upper and lower threshold value setting mode. Increment key ) ( • The settable digit is shifted cyclically at every press of the key during the initial setting mode. • Pressing the key increases the set value, in the upper and lower threshold value setting mode. 7 Decrement key ) ( • The set condition changes at every press of the key during the initial setting mode. • Pressing the key decreases the set value, in the upper and lower threshold value setting mode. 8 • Three modes, the sensing mode, the lower threshold value (M1) setting mode, and the upper threshold value (M2) setting mode, are cyclically selected at every press of the key. • During the sensing mode, pressing the key for Mode selection key 4 sec., or more, can make the key protection ( MODE ) either effective or ineffective. ) and • Holding the increment key ( simultaneously pressing the mode selection key brings the sensor from the sensing mode to the initial setting mode. 9 Pressure Lo-port Lower pressure should be applied. 10 Pressure Hi-port Higher pressure should be applied. FA COMPONENTS MACHINE VISION SYSTEMS 6 Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DP-100 DP-M ) (M1 < M2) Hysteresis 1 digit The measured differential pressure level, setting values, error codes, and key protection sign are displayed. Upper threshold value (M2) High pressure • The comparative outputs can be made ON or OFF by a pressure within the limits set by the upper and the lower threshold levels. 8 MEASUREMENT SENSORS UV CURING SYSTEMS Lower threshold value (M1) 3 SENSOR OPTIONS ENERGY CONSUMPTION VISUALIZATION COMPONENTS • The lower threshold value and the upper threshold value establish the hysteresis of the comparative output. 9 PARTICULAR USE SENSORS ) (M1 < M2) ON Comparative output when set OFF to NO ON Comparative output when set OFF to NC 1 PRESSURE / FLOW SENSORS LASER MARKERS Hysteresis mode ( Hysteresis Functional description INDUCTIVE PROXIMITY SENSORS Refer to p.1472 for general precautions. Output mode and output operation • The analog current output of DP-M2A does not incorporate a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. LIGHT CURTAINS / SAFETY COMPONENTS STATIC ELECTRICITY PREVENTION DEVICES DP-M SERIES Hysteresis 1 digit 1 digit = 0.01 kPa.D {1 mmH2O.D} Comparative ON output when set to NC OFF 0 Lower threshold value (M1) Upper threshold value (M2) High pressure • When operating in window comparator mode ( ) lower threshold value (M1) and upper threshold value (M2) should be set with a difference of 3 digits (0.03 kPa.D {3 mmH2O.D}) or more. Others During the sensing mode, pressing both switches calibrates the sensor into atmospheric zero. • Use within the rated pressure range. • Do not apply pressure exceeding the pressure withstandability value. The diaphragm will get damaged and correct operation shall not be maintained. • Do not use during the initial transient time (0.5 sec.) after the power supply is switched on. • Do not insert wires, etc., into the pressure port. The diaphragm will get damaged and correct operation shall not be maintained. • Do not operate the keys with pointed or sharp objects. Micro-differential Pressure High-precision Digital Pressure Sensor DIMENSIONS (Unit: mm in) DP-M SERIES The CAD data in the dimensions can be downloaded from our website. DP-M□ Sensor Pressure unit indicator (mmH2O) (Red) 3 digit LED display (Red) 40 1.575 M1 setting indicator (Red) 2-M3 female threads, 6 0.236 deep 32.5 1.280 ø4.6 ø0.181 5.5 0.217 Increment key Decrement key ø3.7 ø0.146 cable, 2 m 6.562 ft long Mode selection key 17 0.669 LASER SENSORS MICRO PHOTOELECTRIC SENSORS 25 0.984 AREA SENSORS 10.6 0.417 ø4.6 ø0.181 40 1.575 Operation indicator (Orange) FIBER SENSORS PHOTOELECTRIC SENSORS Pressure Lo-port 42.3 1.665 30 1.181 Pressure unit indicator (kPa) (Red) M2 setting indicator (Red) 756 LIGHT CURTAINS / SAFETY COMPONENTS 13.6 0.535 PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Pressure Hi-port PARTICULAR USE SENSORS MS-PE-1 Sensor mounting bracket (Optional) 2-ø6.4 ø0.252 mounting holes Assembly dimensions 25 0.984 25 0.984 SIMPLE WIRE-SAVING UNITS 2-ø6.4 0.252 mounting holes WIRE-SAVING SYSTEMS 25 0.984 4-ø3.4 ø0.134 mounting holes ø25 ø0.984 38 1.496 25 0.984 55 2.165 13 0.512 13 0.512 MEASUREMENT SENSORS 30 1.181 t2 t 0.079 42.3 1.665 30 1.181 40 1.575 25 0.984 53 2.087 38 1.496 25 0.984 2 0.079 10.6 0.417 22.5 0.886 Two M3 (length 8 mm 0.315 in) screws with washers are attached. 47.5 1.870 28.6 1.126 15 0.591 LASER MARKERS HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS 17 0.669 MS-PE-2 MS-PE-3 STATIC ELECTRICITY PREVENTION DEVICES PLC 40 1.575 Material: Cold rolled carbon steel (SPCC) FA COMPONENTS Panel mounting bracket, front protection cover (Optional) MACHINE VISION SYSTEMS UV CURING SYSTEMS Assembly dimensions 51.2 2.016 48 1.890 SENSOR OPTIONS 9.5 0.374 4 0.157 39.3 1.547 Panel cut-out dimensions 55.4 2.181 (27) (1.063) 70 2.756 10.6 0.417 45 +0.6 0 1.772 +0.024 0 48 51.2 1.890 2.016 (6.4) (0.252) 10.5 0.413 70 2.756 45 +0.6 0 1.772 +0.024 0 Pressure/ Digital Display Pressure/ Head-separated Flow DP-100 portion shows the front protection cover. Material: Polycarbonate (Front protection cover) Nylon 6, Polyacetal (Panel mounting bracket) Selection Guide Note: The panel thickness should be 1 to 3.2 mm 0.039 to 0.126 in. DP-M