MS-SF2B-1

603 FIBER SENSORS Safety Light Curtain Type 2 SF2B SERIES Ver.2 Related Information LASER SENSORS ■■General terms and conditions.............. F-3 ■■SF-C11/C13......................................P.663~ ■■Selection guide...............................P.457~ ■■SF-C21.............................................. P.647~   Glossary of terms........................ P.1549~   General precautions...................... P.1595 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Listing AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Conforming to Conforming to Certified Certified* (SF4B-□-03only) Protection Conventional: IP65 (IEC) SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS Conforming to 4584 (Excluding SF4B-□-03) Upgraded to version 2.0 from January 2009 shipments. SENSOR OPTIONS STATIC CONTROL DEVICES OSHA/ANSI Upgrade Guide PARTICULAR USE SENSORS MEASUREMENT SENSORS OSHAListing / ANSI Approved Conforming to Machine & EMC Directive Ver.2: IP65 / IP67 (IEC, JIS) Category 2 PLc SIL1 panasonic.net/id/pidsx/global The control category differs depending on the configuration and wiring of the external circuit. Type 2 safety solution International regulations for safety measures at reasonable cost Protective structure IP67* is achieved with a seamless structure that has reduced seams *Version 2.0 or later The inner unit is protected by a cylindrical inner case. The seams of unit and lens surfaces have been greatly reduced, so that particles of oil mists and dust are prevented from getting in. End unit Internal unit MACHINE VISION SYSTEMS UV CURING SYSTEMS Protective case Inner case Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights The photograph shows a cut-away model. Extensive range of variations available with sensing widths from 168 mm to 1,912 mm 6.614 in to 75.275 in Two types are available for different minimum sensing object sizes. Hand protection type SF2B-H□ Minimum sensing object ø27 mm ø1.063 in 20 mm 0.787 in beam pitch Arm / Foot protection type SF2B-A□ Minimum sensing object ø47 mm ø1.850 in 40 mm 1.575 in beam pitch Safety Light Curtain Type 2 SF2B SERIES Ver.2 Series connection of up to three sets is possible Sub-sensors for series connection (optional) can be used to connect up to three sets of safety light curtains (up to a total of 128 beam channels maximum; however, the SF2B-A□ allows up to 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). • The safety light curtains and the sub-sensors for serial connection (optional) have different models. When connecting safety light curtains in series, be sure to use the sub-sensors for serial connection and serial connection cables which are sold separately. • The SF2B-H8-□ and SF2B-A4-□ cannot be connected in series. For details, refer to “Series connection” of “PRECAUTIONS FOR PROPER USE” (p.620~). Sub-sensor for series connection only SF2B-□SL (Optional) Sub-sensor for series connection only SF2B-□SL (Optional) Hand protection type and Arm / Foot protection type can be used together. Arm / Foot protection type Hand protection type FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Safety light curtain SF2B-□ Cables for series connection SF2B-CSL□ (Optional) 604 SENSOR OPTIONS “ZERO” dead zone. Unit length = protective height, so mounting is possible with no dead zone New concept SIMPLE WIRE-SAVING UNITS The sensing area contains no dead spaces. Even with series connections, there are no dangerous openings at the interfaces between safety light curtains. This makes a simpler and more compact installation possible. WIRE-SAVING SYSTEMS SF2B MEASUREMENT SENSORS Previous model “ZERO” dead zone when using series mounting Dead zone when using series mounting STATIC CONTROL DEVICES Gaps occurred at connecting point LASER MARKERS It used to be necessary to install a cover or offset the safety light curtain in order to eliminate gaps. HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Dead zone “ZERO” dead zone when using L-shaped mounting PLC Overlapped mounting when using L-shaped mounting Complex installation Increased design and installation man-hours FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Overlapped mounting Note: The SF2B-H8-□ and SF2B-A4-□ cannot connected in series. For details, refer to “PRECAUTIONS FOR PROPER USE” (p.620~). Mutual interference is reduced without need for interference prevention lines Reducing the number of malfunctions caused by extraneous light The scan timing of the safety light curtain is automatically shifted in order to reduce mutual interference. A double scanning method and retry processing are new functions exclusive to that are effective in eliminating the effect of momentary extraneous light from peripheral equipment. Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C SF2B SF2B BSF4-AH80 SF2B SF2C Definition of Sensing Heights Irregular reflected light Extraneous light (flasher) Extraneous light (Obstacle detecting sensor) 605 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Safety Light Curtain Type 2 SF2B SERIES Ver.2 Equipped with a digital error indicator so that error details can be understood at a glance Beam-axis alignment indicators show the incident light position at a glance The system constantly checks the safety light curtain for problems such as incorrect cable wiring, disconnection, short-circuits, internal circuit problems, and incoming light problems. If a problem should occur, details of the error appear on the digital display. Therefore, smooth support is possible if problems occur at startup and during maintenance operations, even if assistance is given via telephone. Beam-axis alignment indicators display the beam channels of the safety light curtain in four blocks. The blocks where the beam axes match will light up in red in turn. When all the beam axes receive light, all the LEDs light up green. Furthermore, a stability indicator (STB.) lights up when there is sufficient incoming light. Normal operation Beam-axis alignment indicator Breaking out error A B PARTICULAR USE SENSORS C SENSOR OPTIONS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Adapter cables and adapter mounting brackets are available so that previous peripheral devices for safety light curtains can still be used The safety light curtain SF2-A / SF2-N series (discontinued model), area sensor NA40 series, and SF1-N series (discontinued model) can be replaced with the SF2B series using the current mounting holes and connection cables. Selectable safety circuits The safety light curtain unit has a built-in monitoring function for external devices (such as fused relay monitoring). This supports the construction of safety light curtain peripheral safety circuits which do not use a safety relay unit, and contributes to reduced costs and a more compact control panel. In addition, a connectable control unit is used, so that a safety circuit that is easy to construct and easy to install can be selected. FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights D * When using the SF2B-CB05-B adapter cable, the beam axis alignment indicator of emitter cannot be used. Digital error indicator Utilizing safety light curtain functions Utilizing connectable control unit Reduced component costs WIRE-SAVING SYSTEMS Beam-axis alignment indicator Less processing SIMPLE WIRE-SAVING UNITS •Recommended safety relays Panasonic Corporation Model No.: SF relay, slim type Monitor SF relay, slim type SF2B series Safety relay, etc. Contactor, etc. Uses external device monitoring function Motor, etc. Note: Construct a separate reset input circuit. DIN terminal block SF relay, slim type SFS3-L-DC24V (AG1S132) SFS4-L-DC24V (AG1S142) DIN terminal block SFS4-SFD (AG1S847) [4-poles type] SFS6-SFD (AG1S867) [6-poles type] Reset input Monitor SF2B series Uses SF-C11 connectable control unit Contactor, etc. Motor, etc. Significant cost reduction is achieved by using corner mirror By using a single corner mirror, safety light curtain and peripheral safety circuit for one set are eliminated. Enables significant cost reduction and savings on wiring. The control category is unchanged. When setting up the safety light curtains in the L-shape or U-shape, usually two or three sets of the safety light curtains are required. However, using the corner mirror to reflect the laser light allows only one set of the safety light curtains to be set up at the L-shape or U-shape. Corner mirror RF-SFBH-□ Note: Contact the manufacturers for details on the recommended products. Safety Light Curtain Type 2 SF2B SERIES Ver.2 PRODUCT CONFIGURATION 606 FIBER SENSORS LASER SENSORS 6 Sub-sensor for series connection only / p.609 PHOTOELECTRIC SENSORS (Optional, use for connect in series) • Mounting bracket and mating cable are optional. • When using series connection, sub-sensors for serial connection are needed in addition to the safety light curtains. 5 Cable for series connection / p.608 (Optional, use for connect in series) * 1 Safety light curtain / p.606 * 1 , 2 and 3 are required. 4 Extension cable / p.608 (Optional, use for cable extension) Hand protection type Arm / Foot protection type Min. sensing object ø47 mm ø1.850 in (40 mm 1.575 in beam pitch) Min. sensing object ø27 mm ø1.063 in (20 mm 0.787 in beam pitch) Operating range (Note 1) Appearance 6 mm 0.236 in (Note 3) Protective height (Note 4) 0.2 to 13 m 0.656 to 42.651 ft Beam pitch 6 mm 20 mm 0.787 in 0.236 in Beam channel No. INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS 1 Safety light curtains Mounting bracket and bottom cap cable are not supplied with the safety light curtain. Be sure to order them separately. Beam channel No. SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PARTICULAR USE SENSORS ORDER GUIDE Type AREA SENSORS PRESSURE / FLOW SENSORS * 3 Bottom cap cable (Optional) / p.608 * 2 Mounting bracket (Optional) / p.607 MICRO PHOTOELECTRIC SENSORS When using the adapter cable SF2B-CB05-B: 0.2 to 5 m 0.656 to 16.404 ft 6 mm 0.236 in (Note 3) Protective height (Note 4) Beam pitch 40 mm 1.575 in 26 mm 1.024 in 0.2 to 13 m 0.656 to 42.651 ft When using the adapter cable SF2B-CB05-B: 0.2 to 5 m 0.656 to 16.404 ft Model No. (Note 5) NPN output type PNP output type SF2B-H8-N (Note 2) SF2B-H12-N SF2B-H16-N SF2B-H20-N SF2B-H24-N SF2B-H28-N SF2B-H32-N SF2B-H36-N SF2B-H40-N SF2B-H48-N SF2B-H56-N SF2B-H64-N SF2B-H72-N SF2B-H80-N SF2B-H88-N SF2B-H96-N SF2B-A4-N (Note 2) SF2B-A6-N SF2B-A8-N SF2B-A10-N SF2B-A12-N SF2B-A14-N SF2B-A16-N SF2B-A18-N SF2B-A20-N SF2B-A24-N SF2B-A28-N SF2B-A32-N SF2B-A36-N SF2B-A40-N SF2B-A44-N SF2B-A48-N SF2B-H8-P (Note 2) SF2B-H12-P SF2B-H16-P SF2B-H20-P SF2B-H24-P SF2B-H28-P SF2B-H32-P SF2B-H36-P SF2B-H40-P SF2B-H48-P SF2B-H56-P SF2B-H64-P SF2B-H72-P SF2B-H80-P SF2B-H88-P SF2B-H96-P SF2B-A4-P (Note 2) SF2B-A6-P SF2B-A8-P SF2B-A10-P SF2B-A12-P SF2B-A14-P SF2B-A16-P SF2B-A18-P SF2B-A20-P SF2B-A24-P SF2B-A28-P SF2B-A32-P SF2B-A36-P SF2B-A40-P SF2B-A44-P SF2B-A48-P Number of beam channels Protective height (mm in) (Note 4) 8 168 6.614 12 232 9.134 16 312 12.283 20 392 15.433 24 472 18.583 28 552 21.732 32 632 24.882 36 712 28.031 40 792 31.181 48 952 37.480 56 1,112 43.779 64 1,272 50.079 72 1,432 56.378 80 1,592 62.677 88 1,752 68.976 96 1,912 75.275 4 168 6.614 6 232 9.134 SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 8 312 12.283 10 392 15.433 12 472 18.583 14 552 21.732 Safety Control Units 16 632 24.882 18 712 28.031 Safety Components 20 792 31.181 24 952 37.480 28 1,112 43.779 SF4B/ SF4B-G 32 1,272 50.079 SF4B-C 36 1,432 56.378 SF4C 40 1,592 62.677 BSF4-AH80 44 1,752 68.976 48 1,912 75.275 Notes: 1) The “operating range” is the possible setting distance between the emitter and the receiver. 2) The SF2B-H8-□ and SF2B-A4-□ cannot be connected in series Actual operating Receiver cannot be because they do not include a connector for series connection. placed in this range 0.2 m range of the sensor Refer to “PRECAUTIONS FOR PROPER USE” (p.620~) for 0.656 ft Setting range of details. the receiver 3) The distance between the tip of the safety light curtain and the last beam axis of the SF2B-H8-□ and SF2B-A4-□ is 22 mm 0.866 in. 4) Refer to “Definition of sensing heights” (p.645) for details of the protective height. E theEMITTER 5) Models which have an “ E EMITTER ” symbol in model No. on the Emitter Receiver name plate are emitters, and those with a “ D RECEIVER ” symbol are D RECEIVER receivers. 13 m 42.651 ft When using the SF2B-CB05-B: 5 m 16.404 ft Receiver Selection Guide Safety Light Curtains SF4D SF2B SF2C Definition of Sensing Heights 607 Safety Light Curtain Type 2 ORDER GUIDE FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS SF2B SERIES Ver.2 2 Mounting brackets Mounting bracket is not supplied with the safety light curtain. Be sure to order it separately. • MS-SF2B-1 Designation Appearance Model No. AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS Standard mounting bracket MS-SF2B-1 MS-SF2B-3 Mounting of the safety light curtain is possible so that the mounting bracket does not project past the protective height (safety light curtain length). 4 pcs. per set for emitter and receiver INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS Dead zoneless mounting bracket SIMPLE WIRE-SAVING UNITS For SF2-A / SF2-N STATIC CONTROL DEVICES LASER MARKERS For rear and side mounting MEASUREMENT SENSORS MS-SF2B-5 UV CURING SYSTEMS For NA40 Selection Guide Safety Light Curtains Safety Control Units Safety Components For SF1-N For rear mounting MS-SF2B-4 For side mounting MACHINE VISION SYSTEMS For SF1-N / NA40 MS-SF2B-6 for ( Accessory MS-SF2B-1 ) Safety light curtain Sensing surface Four bracket set M3 (length 5 mm 0.197 in) hexagon-socket-head bolts are attached. 8 pcs. for safety light curtain mounting; 8 pcs. for beam axis adjustment Used when replacing units in the SF2-A / SF2-N series. (discontinued model) 4 pcs. per set for emitter and receiver Used when replacing units in the SF1-N (discontinued model) / NA40 series which are using the MS-SF1-1 / MS-NA40-1 sensor mounting brackets.(Note) 4 pcs. per set for emitter and receiver Used when replacing units in the NA40 series which are side mounted (direct mounted).(Note) 4 pcs. per set for emitter and receiver Dead zoneless mounting bracket MS-SF2B-3 Safety light curtain Sensing surface Four bracket set Six spacers for the intermediate supporting bracket and twelve M5 (length 8 mm 0.315 in) hexagon-socket-head bolts are attached. • MS-SF2B-5 Adapter mounting brackets MS-SF2B-5 SF4B-C SF4C MS-SF2B-7 Used when replacing units in the SF1-N series (discontinued model) which are side mounted (discontinued model). 4 pcs. per set for emitter and receiver Sensing surface Four bracket set M3 (length 5 mm 0.197 in) hexagon-socket-head bolts are attached. 8 pcs. for safety light curtain mounting; 8 pcs. for beam axis adjustment Note: SF1-N-compatible mounting bracket can also be used for SF1-S / SF1-A series products that are discontinued. The NA40-compatible mounting bracket can also be used for NA40-S / NA40-B series products that are discontinued. • MS-SF2B-6 Hexagon-socket-head bolt [M3 (length 5 mm 0.197 in)] BSF4-AH80 SF2B SF2C Hexagon-socket-head bolts [M3 (length 5 mm 0.197 in)] for ( Accessory MS-SF2B-5 ) SF4D SF4B/ SF4B-G Hexagon-socket-head bolts [M3 (length 5 mm 0.197 in)] Safety light curtain For side mounting FA COMPONENTS Adapter mounting brackets PLC ENERGY MANAGEMENT SOLUTIONS Standard mounting bracket MS-SF2B-1 • MS-SF2B-3 WIRE-SAVING SYSTEMS HUMAN MACHINE INTERFACES Description Used to mount the safety light curtain on the rear surface and side surface 4 pcs. per set for emitter and receiver PRESSURE / FLOW SENSORS PARTICULAR USE SENSORS Standard mounting bracket Adapter mounting bracket MS-SF2B-6 • MS-SF2B-7 for ( Accessory MS-SF2B-6 ) Accessory for MS-SF2B-7 Definition of Sensing Heights Sensing surface Four bracket set Eight M3 (length 5 mm 0.197 in) hexagon-sokethead bolts are attached. Adapter mounting bracket MS-SF2B-4 Hexagon-socket-head bolt [M3 (length 5 mm 0.197 in)] for ( Accessory MS-SF2B-4 ) Adapter mounting bracket MS-SF2B-7 Safety light curtain Sensing surface • MS-SF2B-4 Hexagon-socket-head bolt [M3 (length 5 mm 0.197 in)] Safety light curtain Safety light curtain Sensing surface Adapter mounting bracket MS-SF2B-7 Four bracket set Hexagon-socket-head bolt Eight M3 (length 5 mm 0.197 in) hexagon-soket- [M3 (length 5 mm 0.197 in)] head bolts are attached. Sensing surface Four bracket set Eight M3 (length 5 mm 0.197 in) hexagon-sockethead bolts are attached. Safety Light Curtain Type 2 SF2B SERIES Ver.2 ORDER GUIDE 3 4 FIBER SENSORS 5 Bottom cap cable / Extension cable / Cables for series connection Mating cable is not supplied with the safety light curtain. Be sure to order it separately. Type Appearance Model No. Bottom cap cable Discrete wire SF2B-CCB3 SF2B-CCB7 SF2B-CCB10 SF2B-CCB15 Discrete wire With connectors on both ends For receiver For emitter SFB-CC10 SFB-CCJ10E SFB-CCJ10D For SF2-A / SF2-N For SF1‑N / NA40 Extension cable Adapter cable (Bottom cap cable) 3 * SFB-CC3 SF2B-CB05-A SF2B-CB05-B 5 Description Cable length: 3 m 9.843 ft Net weight: 370 g approx. (2 cables) Cable length: 7 m 22.966 ft Net weight: 820 g approx. (2 cables) Cable length: 10 m 32.808 ft Net weight: 1,160 g approx. (2 cables) Cable length: 15 m 49.213 ft Net weight: 1,720 g approx. (2 cables) * Used in conjunction with subsensor for serial connection only. Used for connecting to the safety light curtain and to other cables or the SF-C13 control unit. Two cables per set for emitter and receiver Cable outer diameter: ø6 mm ø0.236 in Cable color: Gray (for emitter) Gray with black line (for receiver) The min. bending radius: R6 mm R0.236 in Cable length: 0.5 m 1.640 ft Used for connecting to the safety light curtain and to Net weight: 95 g approx. (2 cables) an extension cable or the SF-C11 control unit. Two cables per set for emitter and receiver Cable length: 5 m 16.404 ft Cable outer diameter: ø6 mm ø0.236 in Net weight: 620 g approx. (2 cables) Connector outer diameter: ø14 mm ø0.551 in max. Cable color: Gray (for emitter), Gray with black line (for receiver) Cable length: 10 m 32.808 ft Connector color: Gray (for emitter), Black (for receiver) Net weight: 1,200 g approx. (2 cables) The min. bending radius: R6 mm R0.236 in Used for cable extension or connecting to the SF-C13 control unit. Cable length: 3 m 9.843 ft Two cables per set for emitter and receiver Net weight: 380 g approx. (2 cables) Cable outer diameter: ø6 mm ø0.236 in Cable length: 10 m 32.808 ft Connector outer diameter: ø14 mm ø0.551 in max. Net weight: 1,200 g approx. Cable color: Gray (for emitter), Gray with black line (for receiver) (2 cables) The min. bending radius: R6 mm R0.236 in Cable length: 10 m 32.808 ft Used for cable extension or connecting to the SF-C11 control unit. One each for emitter and receiver Net weight: 580 g approx. Cable outer diameter: ø6 mm ø0.236 in (1 cable) Connector outer diameter: ø14 mm ø0.551 in max. Cable length: 10 m 32.808 ft Cable color: Gray (for emitter), Gray with black line (for receiver) Net weight: 600 g approx. Connector color: Gray (for emitter), Black (for receiver) (1 cable) The min. bending radius: R6 mm R0.236 in Cable length: 0.5 m 1.640 ft Net weight: 95 g approx. (2 cables) Cable length: 0.5 m 1.640 ft Net weight: 95 g approx. (2 cables) * Please contact our office for wiring of adapter cables. Cable for series connection 4-core cable SF2B-CB5 SF2B-CB10 4 8-core cable Connector 3 SF2B-CB05 SF2B-CSL01 Cable length: 0.1 m 0.328 ft Net weight: 70 g approx. (2 cables) SF2B-CSL05 Cable length: 0.5 m 1.640 ft Net weight: 120 g approx. (2 cables) Used when replacing units in the SF2-A / SF2-N series (discontinued model). The SF2N-CC□ cable with connector can be used without change, so that replacement with SF2B series units can be done smoothly. Two cables per set for emitter and receiver Cable outer diameter: ø6 mm ø0.236 in Connector outer diameter: ø14 mm ø0.551 in max. Cable color: Gray (for emitter), Gray with black line (for receiver) Connector color: Gray (for emitter), Black (for receiver) The min. bending radius: R6 mm R0.236 in Used when replacing units in the SF1-N (discontinued model) / NA40 series. The SF1-CC□ / NA40-CC□ cable with connector can be used without change, so that replacement with SF2B series units can be done smoothly. Two cables per set for emitter and receiver Cable outer diameter: ø6 mm ø0.236 in Connector outer diameter: ø14 mm ø0.551 in max. Cable color: Gray (for emitter), Gray with black line (for receiver) Connector color: Gray (for emitter), Black (for receiver) The min. bending radius: R6 mm R0.236 in Use when connecting the sub-sensor for series connection to the safety light curtain in series. Two cables per set for emitter and receiver (common for emitter and receiver) Cable outer diameter: ø6 mm ø0.236 in Cable color: Gray (common for emitter and receiver) The min. bending radius: R6 mm R0.236 in * Interchangeability function • This function is used for replacing other safety light curtains or area sensors with these new units. The bottom cap cables and sensor mounting brackets used will vary depending on the models being replaced. Refer to the instruction manual for details on actual wiring and mounting. Models being replaced Adapter cable 608 Adapter mounting bracket Details of changes and points to note • NPN output type: Connect the shielded wire to +V. PNP output type: Connect the shielded wire to 0 V. SF2-A / SF2-N series • Existing SF2N-CC□ connection cables (optional) can be used without change. SF2B-CB05-A MS-SF2B-5 (Discontinued product) • The interference prevention function (parallel connection) cannot be used. • Emitter: Synchronization cable has changed to interference prevention cable.(Note 1) When using the MS-SF1-1: SF1-N series Receiver: Synchronization cable has changed to control output (OSSD 1).(Note 2)(Note 3) SF2B-CB05-B MS-SF2B-4 • Existing SF1-CC□A connection cables (optional) can be used without change. (Discontinued product) For direct mounting: MS-SF2B-7 • The beam axis alignment indicator of emitter cannot be used. • Control output (OSSD 2) is equipped instead of self-diagnosis output.(Note 3) • Emission halt function cannot be used. When using the MS-NA40-1: NA40 series SF2B-CB05-B MS-SF2B-4 • Existing NA40-CC□ connection cables (optional) can be used without change. For direct mounting: MS-SF2B-6 • The ambient temperature for the NA40-CC□ connection cables (optional) is –10 to +50 °C +14 to +122 °F. Notes: 1) Not used in case of simple replacement of the SF1-N series (interference prevention wire is unused), therefore perform wire insulation so that it will not touch other wires. 2) Not used in case of simple replacement of the SF1-N series (non-safety applications), therefore perform wire insulation so that it will not touch other wires. 3) When used in safety applications, both OSSD1 and OSSD2 must be used. LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 609 Safety Light Curtain Type 2 ORDER GUIDE FIBER SENSORS Type MICRO PHOTOELECTRIC SENSORS AREA SENSORS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS Hand protection type SAFETY LIGHT CURTAINS / SAFETY COMPONENTS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C Arm / Foot protection type PLC Min. sensing object ø27 mm ø1.063 in (20 mm 0.787 in beam pitch) PHOTOELECTRIC SENSORS The sub-sensors for series connection are PNP / NPN types. Furthermore, they cannot simply 6 Sub-sensor for series connection only be used by themselves. Always be sure to use them in combination with safety light curtains. Min. sensing object ø47 mm ø1.850 in (40 mm 1.575 in beam pitch) LASER SENSORS SF2B SERIES Ver.2 Operating range (Note 1) Appearance Model No. (Note 6) Number of Protective height beam (mm in) (Note 4) channels SF2B-H8SL (Note 2) Beam channel No. 6 mm 0.236 in (Note 3) Protective height (Note 4) 0.2 to 13 m 0.656 to 42.651 ft Beam pitch 6 mm 20 mm 0.787 in 0.236 in When using SF2B-CB05-B adapter cable at safety light curtain: 0 .2 to 5 m 0.656 to 16.404 ft 8 168 6.614 SF2B-H12SL 12 232 9.134 SF2B-H16SL 16 312 12.283 SF2B-H20SL 20 392 15.433 SF2B-H24SL 24 472 18.583 SF2B-H28SL 28 552 21.732 SF2B-H32SL 32 632 24.882 SF2B-H36SL 36 712 28.031 SF2B-H40SL 40 792 31.181 SF2B-H48SL 48 952 37.480 SF2B-H56SL 56 1,112 43.779 SF2B-H64SL 64 1,272 50.079 SF2B-H72SL 72 1,432 56.378 SF2B-H80SL 80 1,592 62.677 SF2B-H88SL 88 1,752 68.976 SF2B-H96SL 96 1,912 75.275 SF2B-A4SL (Note 2) 4 168 6.614 SF2B-A6SL 6 232 9.134 SF2B-A8SL Beam channel No. 6 mm 0.236 in (Note 3) Protective height (Note 4) Beam pitch 40 mm 1.575 in 26 mm 1.024 in 0.2 to 13 m 0.656 to 42.651 ft When using SF2B-CB05-B adapter cable at safety light curtain: 0 .2 to 5 m 0.656 to 16.404 ft 8 312 12.283 SF2B-A10SL 10 392 15.433 SF2B-A12SL 12 472 18.583 SF2B-A14SL 14 552 21.732 SF2B-A16SL 16 632 24.882 SF2B-A18SL 18 712 28.031 SF2B-A20SL 20 792 31.181 SF2B-A24SL 24 952 37.480 SF2B-A28SL 28 1,112 43.779 SF2B-A32SL 32 1,272 50.079 SF2B-A36SL 36 1,432 56.378 SF2B-A40SL 40 1,592 62.677 SF2B-A44SL 44 1,752 68.976 SF2B-A48SL 48 1,912 75.275 RECEIVER Spare parts (AccessoriesD for safety light curtain) Designation Appearance Emitter: 20 mA or less Receiver: 35 mA or less Emitter: 30 mA or less Receiver: 45 mA or less Emitter: 30 mA or less Receiver: 55 mA or less Emitter: 40 mA or less Receiver: 65 mA or less Emitter: 45 mA or less Receiver: 85 mA or less Emitter: 50 mA or less Receiver: 105 mA or less Emitter: 60 mA or less Receiver: 125 mA or less Emitter: 15 mA or less Receiver: 20 mA or less Emitter: 15 mA or less Receiver: 25 mA or less Emitter: 20 mA or less Receiver: 30 mA or less Emitter: 20 mA or less Receiver: 35 mA or less Emitter: 25 mA or less Receiver: 40 mA or less Emitter: 25 mA or less Receiver: 50 mA or less Emitter: 30 mA or less Receiver: 60 mA or less Emitter: 35 mA or less Receiver: 70 mA or less Intermediate supporting bracket Model No. Description MS-SF2B-2 Used to mount the safety light curtain on the intermediate position. Mounting is possible behind or at the side of the safety light curtain. BSF4-AH80 SF2C Emitter: 20 mA or less Receiver: 25 mA or less Notes: 1) The “operating range” is the possible setting distance between the emitter and the receiver. 2) The SF2B-H8SL and SF2B-A4SL do not include a connector for series connection. Therefore, when connecting 3 sets in series, the sub-sensor can be used only for the third set. Refer to “PRECAUTIONS FOR PROPER USE” (p.620~) for details. 3) The distance between the tip of the safety light curtain and the top beam axis of the SF2B-H8SL and SF2B-A4SL is 22 mm 0.866 in. 4) Refer to “Definition of sensing heights” (p.645) for details of the protective height. 5) The specifications of the sub-sensor for series connection are the same as for the safety light curtain, except for the current consumption. E EMITTER However, the sub-sensor is not equipped with an output. 6) Models which have an “ E EMITTER ” symbol in the model No. on the name plate are emitters, and those with a “ D RECEIVER ” symbol are receivers. SF4C SF2B Current consumption (Note 5) Intermediate supporting bracket (Note) Definition of Sensing Heights • MS-SF2B-2 M5 hexagonsocket-head bolt Purchase separately. ( ) Intermediate supporting bracket MS-SF2B-2 Safety light curtain Sensing surface Test rod ø27 SF2B-TR27 Min. sensing object for regular checking (ø27 mm ø1.063 in), with hand protection type (min. sensing object ø27 mm ø1.063 in) Note: Depending on the product, the required set number will vary as follows. 1 set: SF2B-H□…40 to 56 beam channels, SF2B-A□…20 to 28 beam channels 2 sets: SF2B-H□…64 to 80 beam channels, SF2B-A□…32 to 40 beam channels 3 sets: SF2B-H□…88 to 96 beam channels, SF2B-A□…44 to 48 beam channels M5 hexagonsockethead bolt Purchase separately. ( ) Sensing surface Intermediate supporting bracket MS-SF2B-2 Safety light curtain Safety Light Curtain Type 2 SF2B SERIES Ver.2 OPTIONS 610 FIBER SENSORS LASER SENSORS Control units Designation Appearance Connector connection type control unit Model No. SF-C11 Description Applicable cable SF2B-CB□ SFB-CCJ10□ PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Use 8-core cable with connector to connect to the safety light curtain. Compatible with up to Control Category 4 (Control Category 2 when used together with the SF2B series). AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Slim type control unit SF-C13 Use a discrete wire cable to connect to the safety light curtain. Compatible with up to Control Category 4 (Control Category 2 when used together with the SF2B series). SF2B-CCB□ SFB-CC□ Note: Refer to SF-C10 series pages (p.663~) for the control units. Front protection cover When setting up the safety light curtains in the L-shape or U-shape, usually two or three sets of the safety light curtains are required. However, using the corner mirror to reflect the laser light allows only one set of the safety light curtains to be set up at the L-shape or U-shape. This protects the sensing surfaces of the safety light curtain from flying objects such as welding spatter, oil and water.The operating range reduces when the front protection cover is used. Material: Polycarbonate Sensing range Sensing range (Note) Item Designation Applicable beam channels Front protection cover Type Model No. Corner mirror RF-SFBH-□ With one corner mirror: declined to 90 %, With two corner mirrors: declined to 80 % (When used in combination with the SF2B series) –10 to +55 °C +14 to +131 °F Ambient temperature (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F Sensing range Ambient humidity 30 to 85 % RH, Storage: 30 to 95 % RH 10 to 55 Hz frequency, Vibration resistance 0.75 mm 2.953 in amplitude in X, Y and Z directions for two hours each 300 m/s2 acceleration (30 G approx.) in X, Y Shock resistance and Z directions for three times each Enclosure: Aluminum, Mounting bracket: Stainless Steel, Material Mirror (rear surface mirror): Glass, Side cover: EPDM Intermediate supporting bracket: 1 set (RF-SFBH-40/48/56/64), Accessories 2 sets (RF-SFBH-72/80/88/96) When using the SF2B-CB05-B Only emitter 0.2 to 11.5 m 0.2 to 4.5 m installed 0.656 to 37.730 ft 0.656 to 14.764 ft Only receiver 0.2 to 11.5 m 0.2 to 4.5 m installed 0.656 to 37.730 ft 0.656 to 14.764 ft Both emitter and 0.2 to 10.0 m 0.2 to 4.0 m receiver installed 0.656 to 32.808 ft 0.656 to 13.123 ft Note: The “operating range” is the possible setting distance between the emitter and the receiver. SIMPLE WIRE-SAVING UNITS Specifications • RF-SFBH-□ Environmental resistance • FC-SF2BH-□ PARTICULAR USE SENSORS SENSOR OPTIONS Corner mirror Front protection cover INDUCTIVE PROXIMITY SENSORS Corner mirror RF-SFBH-□ Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. Corner mirror WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Dimensions of effective reflective surface Safety Light Curtains Hand Arm / Foot Model No. Model No. 8 4 FC-SF2BH-8 RF-SFBH-8 173 × 72 mm 6.811 × 2.835 in 12 6 FC-SF2BH-12 RF-SFBH-12 236 × 72 mm 9.291 × 2.835 in 16 8 FC-SF2BH-16 RF-SFBH-16 316 × 72 mm 12.441 × 2.835 in 20 10 FC-SF2BH-20 RF-SFBH-20 396 × 72 mm 15.591 × 2.835 in SF4B/ SF4B-G 24 12 FC-SF2BH-24 RF-SFBH-24 476 × 72 mm 18.740 × 2.835 in SF4B-C 28 14 FC-SF2BH-28 RF-SFBH-28 556 × 72 mm 21.890 × 2.835 in SF4C 32 16 FC-SF2BH-32 RF-SFBH-32 636 × 72 mm 25.039 × 2.835 in BSF4-AH80 36 18 FC-SF2BH-36 RF-SFBH-36 716 × 72 mm 28.190 × 2.835 in SF2B 40 20 FC-SF2BH-40 RF-SFBH-40 796 × 72 mm 31.339 × 2.835 in SF2C 48 24 FC-SF2BH-48 RF-SFBH-48 956 × 72 mm 37.638 × 2.835 in 56 28 FC-SF2BH-56 RF-SFBH-56 1,116 × 72 mm 43.937 × 2.835 in Definition of Sensing Heights 64 32 FC-SF2BH-64 RF-SFBH-64 1,276 × 72 mm 50.236 × 2.835 in 72 36 FC-SF2BH-72 RF-SFBH-72 1,436 × 72 mm 56.535 × 2.835 in 80 40 FC-SF2BH-80 RF-SFBH-80 1,596 × 72 mm 62.835 × 2.835 in 88 44 FC-SF2BH-88 RF-SFBH-88 1,756 × 72 mm 69.134 × 2.835 in 96 48 FC-SF2BH-96 RF-SFBH-96 1,916 × 72 mm 75.433 × 2.835 in Note: The model Nos. given above denote a single unit, not a pair of units. 2 units are required for use in mounting to the emitter / receiver. (Except for corner mirror) Safety Control Units Safety Components SF4D 611 FIBER SENSORS Safety Light Curtain Type 2 SF2B SERIES Ver.2 OPTIONS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Designation Test rod ø47 Appearance Model No. Description SF2B-TR47 Min. sensing object for regular checking (ø47 mm ø1.850 in), with Arm / Foot protection type (min. sensing object ø47 mm ø1.850 in) AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS Specifications INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SIMPLE WIRE-SAVING UNITS • SF-LAT-2B Allows easy beam axis alignment using easy-to-see laser beam PRESSURE / FLOW SENSORS SENSOR OPTIONS Laser alignment tool Laser alignment tool SF-LAT-2B WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS • Supply voltage: 3 V • Battery: 1.5 V (AA size battery) × 2 pcs. (replaceable) (Note) • Battery lifetime: 30 hours approx. of continuous operation (Manganese battery, at +25 °C +77 °F ambient temperature) • Light source: Red semiconductor laser: class 2 (IEC / JIS / FDA) (Max. output: 1 mW, Peak emission wavelength: 650 nm 0.026 mil) • Ambient temperature: 0 to +40 °C +32 to +104 °F (No dew condensation) • Material: ABS (Enclosure) Aluminum (Mounting part:) • Weight: Net weight: 150 g approx. (without batteries) With the auxiliary output of the safety light curtain, the operation is easily observable from various directions. PLC Specifications HUMAN MACHINE INTERFACES • Supply voltage: 24 V DC ±15 % • Current consumption: 12 mA or less • Indicators: Orange LED (8 pcs. used) [Light up when external contact is ON] • Ambient temperature: –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed) • Material: POM (Enclosure) Polycarbonate (Cover) Cold rolled carbon steel (SPCC) (Bracket) • Cable: 0.3 mm2 2-core cabtyre cable, 3 m 9.843 ft long • Net weight: 70 g approx. (including bracket) ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Large display unit for safety light curtain • SF-IND-2 Hexagon-sockethead bolt M5 (length 10 mm 0.394 in or more) (Purchase separately.) Attaches to top of safety light curtain. Tighten together the mounting bracket provided with the safety light curtain (MS-SF2B-1/4/5) and the mounting bracket of SF-IND-2. •Recommended safety relays Panasonic Corporation SF relay, slim type I/O circuit diagrams Color code (Brown) +V Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C Large display unit for safety light curtain + 24 V DC – ±15 % SF-IND-2 (Blue) –V *1 Users’ circuit Internal circuit *1 Non-voltage contact or NPN open-collector transistor or Color code (Brown) +V BSF4-AH80 *1 SF2B + 24 V DC – ±15 % SF2C Definition of Sensing Heights (Blue) –V Internal circuit Users’ circuit *1 Non-voltage contact or PNP open-collector transistor or (Note) : LR6 dry cell batteries are not provided with the product. Please purchase them separately. SF relay, slim type SFS3-L-DC24V (AG1S132) SFS4-L-DC24V (AG1S142) DIN terminal block SFS4-SFD (AG1S847) [4-poles type] SFS6-SFD (AG1S867) [6-poles type] Note: Contact Panasonic Corporation for details on the recommended products. Safety Light Curtain Type 2 SF2B SERIES Ver.2 612 SPECIFICATIONS FIBER SENSORS LASER SENSORS Individual specifications SF2B-H□ PHOTOELECTRIC SENSORS Hand protection type Item Model No. Type Min. sensing object ø27 mm ø1.063 in type (20 mm 0.787 in beam pitch) NPN output SF2B-H8-N SF2B-H12-N SF2B-H16-N SF2B-H20-N SF2B-H24-N SF2B-H28-N MICRO PHOTOELECTRIC SENSORS PNP output SF2B-H8-P SF2B-H12-P SF2B-H16-P SF2B-H20-P SF2B-H24-P SF2B-H28-P 8 12 16 20 24 28 AREA SENSORS 392 mm 15.433 in 472 mm 18.583 in 552 mm 21.732 in Number of beam channels Beam pitch 20 mm 0.787 in Protective height 168 mm 6.614 in Current consumption PFHD 232 mm 9.134 in Emitter: 40 mA or less Receiver: 50 mA or less 312 mm 12.283 in Emitter: 40 mA or less Receiver: 60 mA or less NPN output 6.24 × 10–9 6.44 × 10–9 6.58 × 10–9 6.77 × 10–9 6.91 × 10–9 7.10 × 10–9 PNP output –9 –9 –9 –9 –9 –9 6.04 × 10 6.23 × 10 6.37 × 10 MTTFD 6.57 × 10 6.71 × 10 170 g approx. Model No. Type 280 g approx. 400 g approx. 510 g approx. 610 g approx. Min. sensing object ø27 mm ø1.063 in type (20 mm 0.787 in beam pitch) SF2B-H32-N SF2B-H36-N SF2B-H40-N SF2B-H48-N SF2B-H56-N SF2B-H64-N PNP output SF2B-H32-P SF2B-H36-P SF2B-H40-P SF2B-H48-P SF2B-H56-P SF2B-H64-P 32 36 40 48 56 64 Beam pitch 20 mm 0.787 in Protective height 632 mm 24.882 in PFHD 712 mm 28.031 in Emitter: 50 mA or less Receiver: 80 mA or less Current consumption 792 mm 31.181 in 952 mm 37.480 in Emitter: 60 mA or less Receiver: 90 mA or less 1,112 mm 43.779 in 1,272 mm 50.079 in Emitter: 65 mA or less Receiver: 110 mA or less NPN output 7.24 × 10–9 7.44 × 10–9 7.58 × 10–9 7.91 × 10–9 8.24 × 10–9 8.58 × 10–9 PNP output –9 –9 –9 –9 –9 8.37 × 10–9 7.04 × 10 7.23 × 10 7.37 × 10 MTTFD 7.71 × 10 8.04 × 10 100 years or more Net weight (total of emitter and receiver) 830 g approx. 930 g approx. 1,000 g approx. Model No. NPN output SF2B-H72-N SF2B-H80-N SF2B-H88-N SF2B-H96-N PNP output SF2B-H72-P SF2B-H80-P SF2B-H88-P SF2B-H96-P 72 80 88 96 Number of beam channels Beam pitch 1,500 g approx. 20 mm 0.787 in Protective height Current consumption 1,432 mm 56.378 in 1,592 mm 62.677 in 1,752 mm 68.976 in 1,912 mm 75.275 in Emitter: 70 mA or less Receiver: 130 mA or less Emitter: 80 mA or less Receiver: 150 mA or less NPN output 8.91 × 10–9 9.24 × 10–9 9.58 × 10–9 9.91 × 10–9 PNP output 8.71 × 10–9 9.04 × 10–9 9.37 × 10–9 9.71 × 10–9 1,900 g approx. 2,100 g approx. MTTFD Net weight (total of emitter and receiver) PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC 1,300 g approx. Type Min. sensing object ø27 mm ø1.063 in type (20 mm 0.787 in beam pitch) PFHD 720 g approx. NPN output Number of beam channels Item 6.90 × 10 100 years or more Net weight (total of emitter and receiver) Item Emitter: 50 mA or less Receiver: 70 mA or less SAFETY LIGHT CURTAINS / SAFETY COMPONENTS 1,700 g approx. HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 100 years or more 2,300 g approx. 2,500 g approx. Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. PFHD: Probability of dangerous failure per hour, MTTFD: Mean time to dangerous failure (in years) Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 613 SF2B-A□ PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Type Item WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS SF2B-A4-N SF2B-A6-N SF2B-A8-N SF2B-A10-N SF2B-A12-N SF2B-A14-N PNP output SF2B-A4-P SF2B-A6-P SF2B-A8-P SF2B-A10-P SF2B-A12-P SF2B-A14-P 4 6 8 10 12 14 392 mm 15.433 in 472 mm 18.583 in 552 mm 21.732 in Beam pitch 40 mm 1.575 in Protective height 168 mm 6.614 in PFHD Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights Emitter: 35 mA or less Receiver: 50 mA or less 6.23 × 10–9 6.30 × 10–9 6.42 × 10–9 6.49 × 10–9 6.62 × 10–9 PNP output –9 –9 –9 –9 –9 6.41 × 10–9 5.90 × 10 6.03 × 10 6.10 × 10 MTTFD 6.22 × 10 6.29 × 10 100 years or more Net weight (total of emitter and receiver) 170 g approx. Type Item Emitter: 40 mA or less Receiver: 55 mA or less 6.11 × 10–9 280 g approx. 400 g approx. 510 g approx. 610 g approx. Min. sensing object ø47 mm ø1.850 in type (40 mm 1.575 in beam pitch) SF2B-A16-N SF2B-A18-N SF2B-A20-N SF2B-A24-N SF2B-A28-N SF2B-A32-N PNP output SF2B-A16-P SF2B-A18-P SF2B-A20-P SF2B-A24-P SF2B-A28-P SF2B-A32-P 16 18 20 24 28 32 Number of beam channels Beam pitch 40 mm 1.575 in Protective height 632 mm 24.882 in PFHD 712 mm 28.031 in Emitter: 40 mA or less Receiver: 60 mA or less Current consumption 792 mm 31.181 in 952 mm 37.480 in Emitter: 45 mA or less Receiver: 65 mA or less 1,112 mm 43.779 in 1,272 mm 50.079 in Emitter: 50 mA or less Receiver: 75 mA or less NPN output 6.69 × 10–9 6.81 × 10–9 6.88 × 10–9 7.08 × 10–9 7.27 × 10–9 7.46 × 10–9 PNP output –9 –9 –9 –9 –9 7.26 × 10–9 6.48 × 10 6.61 × 10 6.68 × 10 MTTFD 6.87 × 10 7.07 × 10 100 years or more Net weight (total of emitter and receiver) 830 g approx. 930 g approx. 1,000 g approx. 1,300 g approx. 1,500 g approx. Type Min. sensing object ø47 mm ø1.850 in type (40 mm 1.575 in beam pitch) Item NPN output SF2B-A36-N SF2B-A40-N SF2B-A44-N SF2B-A48-N PNP output SF2B-A36-P SF2B-A40-P SF2B-A44-P SF2B-A48-P 36 40 44 48 Number of beam channels Beam pitch 40 mm 1.575 in Protective height Current consumption PFHD 720 g approx. NPN output 1,432 mm 56.378 in 1,592 mm 62.677 in 1,752 mm 68.976 in 1,912 mm 75.275 in Emitter: 55 mA or less Receiver: 85 mA or less Emitter: 60 mA or less Receiver: 95 mA or less NPN output 7.66 × 10–9 7.85 × 10–9 8.05 × 10–9 8.24 × 10–9 PNP output 7.46 × 10–9 7.65 × 10–9 7.84 × 10–9 8.04 × 10–9 Net weight (total of emitter and receiver) Selection Guide 312 mm 12.283 in NPN output MTTFD Safety Light Curtains 232 mm 9.134 in Emitter: 35 mA or less Receiver: 45 mA or less Current consumption HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Min. sensing object ø47 mm ø1.850 in type (40 mm 1.575 in beam pitch) NPN output Number of beam channels SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS Model No. MICRO PHOTOELECTRIC SENSORS Arm / Foot protection type Model No. LASER SENSORS SF2B SERIES Ver.2 SPECIFICATIONS Model No. FIBER SENSORS Safety Light Curtain Type 2 100 years or more 1,900 g approx. 2,100 g approx. 2,300 g approx. 2,500 g approx. Notes: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. PFHD: Probability of dangerous failure per hour, MTTFD: Mean time to dangerous failure (in years) 1,700 g approx. Safety Light Curtain Type 2 SPECIFICATIONS SF2B SERIES Ver.2 614 Refer to p.667 for the specifications for the control unit. LASER SENSORS Common specifications Type Applicable standards (Note 2) Item Model No. International standard Japan Europe (EU) North America CE marking directive compliance Operating range Min. sensing object Effective aperture angle Supply voltage Control outputs (OSSD 1, OSSD 2) Operation mode Protection circuit Response time Auxiliary output (Aux) (Note 4) Operation mode Protection circuit Synchronization method Interference prevention function Environmental resistance Emission halt function External device monitoring function Degree of protection Ambient temperature / Ambient humidity Ambient illuminance Dielectric strength voltage / Insulation resistance Vibration resistance / Shock resistance Emitting element Cable extension Connecting method Material Accessories FIBER SENSORS Min. sensing object ø27 mm ø1.063 in type (20 mm 0.787 in beam pitch) Min. sensing object ø47 mm ø1.850 in type (40 mm 1.575 in beam pitch) NPN output PNP output NPN output PNP output SF2B-H□-N SF2B-H□-P SF2B-A□-N SF2B-A□-P IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1) JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1) EN 61496-1 (Type 2), EN 55011 UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note 3), OSHA 1910.217 (C) (Note 3), ANSI B11.1 to B11.19, ANSI/RIA 15.06 Machinery Directive, EMC Directive, RoHS Directive 0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable) ø27 mm ø1.063 in opaque object ø47 mm ø1.850 in opaque object ±5° or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)] 24 V DC ±15 %   Ripple P-P 10 % or less NPN open-collector transistor PNP open-collector transistor • Max. sink current: 200 mA • Max. source current: 200 mA • Applied voltage: same as supply voltage • Applied voltage: same as supply voltage [between the control outputs (OSSD 1, OSSD 2) and 0 V] [between the control outputs (OSSD 1, OSSD 2) and +V] • Residual voltage: 2.0 V or less (sink current 200 mA) • Residual voltage: 2.5 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable) (when using 30.5 m 100.066 ft length cable) ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) Incorporated OFF response: 15 ms or less, ON response: 40 to 60 ms NPN open-collector transistor • Max. sink current: 60 mA • Applied voltage: same as supply voltage [between the auxiliary output and 0 V] • Residual voltage: 2.0 V or less (sink current 60 mA) (when using 30.5 m 100.066 ft length cable) PNP open-collector transistor • Max. source current: 60 mA • Applied voltage: same as supply voltage [between the auxiliary output and +V] • Residual voltage: 2.5 V or less (sink current 60 mA) (when using 30.5 m 100.066 ft length cable) When using SF2B-CCB□ or SF2B-CB□: OFF when OSSD ON, ON when OSSD OFF When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted Incorporated Cable synchronization (optical synchronization when using SF2B-CB05-B) Incorporated • Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-A□ allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 5) SF2B-H□ and SF2B-A□ can be used together. (Note 6) When using SF2B-CB05-B (optical synchronization): • Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-A□ allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 5) • Parallel connection: 2 sets max. • Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible. SF2B-H□ and SF2B-A□ can be used together. (Note 6) Incorporated Incorporated IP65 (IEC) (*IP67 is later than Ver.2) –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F / 30 to 85 % RH, Storage: 30 to 95 % RH Incandescent light: 3,500 ℓx or less at the light-receiving face 1,000 V AC for one min. between all supply terminals connected together and enclosure / 20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure 10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each / 300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each Infrared LED (Peak emission wavelength: 870 nm 0.034 mil) Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables. Connector Enclosure: Aluminum, Upper and lower edges : Die-cast zinc alloy, Inner case: Polycarbonate · Polyester resin, Cap: PBT MS-SF2B-2 (Intermediate supporting bracket): (Note 7) MS-SF2B-2 (Intermediate supporting bracket): (Note 7) SF2B-TR27 (Test rod): 1 No. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. 2) Due to revisions of safety light curtain standards (Electro-sensitive protective equipment), type 2 safety light curtains are limited to PLc and SIL1 regarding PL and SIL standards. 3) Not compatible when using the bottom cap cable SF2B-CB05-A. 4) When using auxiliary output (AUX), the compatible cable SF2B-CB05-B (sold separately) cannot be used. 5) SF2B-H8-□ and SF2B-A4-□ cannot be connected in series. For more information, refer to ‘‘PRECAUTIONS FOR PROPER USE’’ (p.620~). 6) When making series connection mixing SF2B-H□ and SF2B-A□, calculate by doubling the number of optical axes only for SF2B-A□, and make the total number of optical axes fall below 128 axes. (e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes. 7) Intermediate supporting bracket MS-SF2B-2 is included with the following products. The number included varies as follows depending on the product. 1 set: SF2B-H□…40 to 56 beam channels, SF2B-A□…20 to 28 beam channels 2 sets: SF2B-H□…64 to 80 beam channels, SF2B-A□…32 to 40 beam channels 3 sets: SF2B-H□…88 to 96 beam channels, SF2B-A□…44 to 48 beam channels PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 615 Safety Light Curtain Type 2 I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS NPN output type Connector pin No. Color code of mating cable Emitter 3 (Blue) 0 V 7 Receiver LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Internal circuit (Shield) (Black) OSSD 1 3 (White) OSSD 2 1 7 Internal circuit Definition of Sensing Heights 2 K1: External device Users’ circuit (Force-guided relay or magnet contactor) – 24 V DC ±15 % 7 5 6 Cable color: Gray with black line (Orange / Black) (Orange) (Brown) 4 (Brown) +V (Shield) (Yellow-green / Black) Auxiliary output (Pink) Test input 3 (Blue) 0 V * S1 Note: Unused wires must be insulated to ensure that they do not come into contact with wires already in use. Emitter + – 24 V DC ±15% 7 2 6 Internal circuit 5 8 3 1 Color code of mating cable 8 4 7 5 6 Cable color: Gray (Orange) Synchronization + (Orange / Black) Synchronization – Users’ circuit (Orange / Black) Synchronization – (Orange) Synchronization + (Brown) +V (Shield) K1 Load (Black) OSSD 1 200 mA max. (White) OSSD 2 (Yellow-green) External device monitoring input 200 mA max. 4 (Blue) 0 V 7 1 3 1 (Pale purple) Not connected 5 K1: External device Users’ circuit (Force-guided relay or magnet contactor) Note: Unused wires must be insulated to ensure that they do not come into contact with wires already in use. CAUTION Construct the interlock (reset input) circuit separately. * S1 Switch S1 • Test input Open: Emission halt 0 to +1.5 V (source current 5 mA or less): Emission K1 K1: External device (Force-guided relay or magnet contactor) Connector pin No. Color code of mating cable Emitter Sensor circuit + 8 4 (Black) K1 (White) Load (Yellow-green) (Blue) • In order to disable the external device monitoring function, connect the auxiliary output and external device monitoring input. At such times, do not connect a load to the auxiliary output. Sensor circuit * S1 (Shield) Switch S1 • Test input Open: Emission halt 0 to +1.5 V (source current 5 mA or less): Emission Internal circuit Load 1 3 * S1 SF2B (Shield) 200 mA max. Construct the interlock (reset input) circuit separately. 2 SF2C Receiver Load CAUTION Receiver (Brown) (Blue) (Pale purple) (Orange) (Orange / Black) Note: Unused wires must be insulated to ensure that they do not come into contact with wires already in use. 6 BSF4-AH80 Cable color: Gray (Pink) (Yellow-green) External device monitoring input 200 mA max. 4 K1 (Blue) 0 V SF4B/ SF4B-G SF4C 7 6 (Yellow-green / Black) K1 8 SF4D SF4B-C Color code of mating cable 8 5 2 Safety Control Units Safety Components 1 4 (Orange / Black) Synchronization – (Orange) Synchronization + 5 (Brown) +V 8 Safety Light Curtains 2 3 * S1 (Orange) Synchronization + 6 (Orange / Black) Synchronization – Users’ circuit 2 Selection Guide 24 V DC ±15 % 6 MEASUREMENT SENSORS STATIC CONTROL DEVICES – 5 Sensor circuit WIRE-SAVING SYSTEMS + 1 (Pale purple) Not connected SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS Emitter (Brown) +V 2 (Shield) 8 Load (Yellow-green / Black) Auxiliary output 4 60 mA max. (Pink) Test input INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Wiring diagram Sensor circuit PRESSURE / FLOW SENSORS When using a SF2B-CCB□ or SF2B-CB□ bottom cap cable I/O circuit diagram AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS SF2B SERIES Ver.2 (Yellow-green / Black) + (Pink) * S1 – 24 V DC ±15 % (Blue) (Pale purple) (Orange) (Orange / Black) Receiver 2 (Brown) (Shield) 1 3 8 4 7 5 6 Cable color: Gray with black line (Orange / Black) (Orange) (Brown) (Shield) (Black) K1 (White) (Yellow-green) Load (Blue) K1: External device (Force-guided relay or magnet contactor) Note: U  nused wires must be insulated to ensure that they do not come into contact with wires already in use. Safety Light Curtain Type 2 SF2B SERIES Ver.2 I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS PNP output type When using a SF2B-CCB□ or SF2B-CB□ bottom cap cable I/O circuit diagram Wiring diagram Connector pin No. Color code of mating cable Emitter Sensor circuit (Brown) +V 2 (Pink) Test input 3 (Yellow-green / Black) Auxiliary output 4 (Shield) 8 (Blue) 0 V – 24 V DC ±15 % 1 (Pale purple) Not connected 6 Internal circuit 2 3 8 7 5 6 Color code of mating cable Cable color: Gray Load – 24 V DC ±15 % (Blue) (Pale purple) (Orange) (Orange / Black) Receiver K1 (Yellow-green) External device monitoring input (Black) OSSD 1 200 mA max. 3 (White) OSSD 2 200 mA max. + Users’ circuit 2 K1 K1: External device (Force-guided relay or magnet contactor) WIRE-SAVING SYSTEMS 8 4 7 5 6 Cable color: Gray with black line CAUTION (Black) (White) (Shield) (Blue) Switch S1 • Test input Open: Emission halt Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note 2) Sensor circuit 4 (Brown) +V (Pink) Test input (Yellow-green / Black) Auxiliary output * S1 + – (Shield) 8 (Blue) 0 V 24 V DC ±15 % 7 6 Internal circuit 6 5 Sensor circuit 2 (Orange / Black) Synchronization – (Orange) Synchronization + (Brown) +V FA COMPONENTS MACHINE VISION SYSTEMS Internal circuit UV CURING SYSTEMS 2 1 3 8 4 7 6 Color code of mating cable Cable color: Gray Users’ circuit K1 K1: External device (Force-guided relay or magnet contactor) CAUTION Construct the interlock (reset input) circuit separately. * S1 Switch S1 • Test input Open: Emission halt Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note 2) Notes: 1) Unused wires must be insulated to ensure that they do not come into contact with wires already in use. 2) Vs is the applying supply voltage. Selection Guide (Brown) Safety Light Curtains (Pink) * S1 (Yellow-green / Black) + (Shield) – 24 V DC ±15 % (Blue) (Pale purple) (Orange) (Orange / Black) Receiver (Yellow-green) External device monitoring input 4 (Black) OSSD 1 200 mA max. 3 (White) OSSD 2 200 mA max. HUMAN MACHINE INTERFACES 5 Load PLC ENERGY MANAGEMENT SOLUTIONS (Orange) Synchronization + (Orange / Black) Synchronization – Users’ circuit 1 (Shield) 8 (Blue) 0 V 7 Load Note: U  nused wires must be insulated to ensure that they do not come into contact with wires already in use. 1 (Pale purple) Not connected 5 LASER MARKERS K1 Emitter Connector pin No. Color code of mating cable 3 STATIC CONTROL DEVICES K1: External device (Force-guided relay or magnet contactor) • In order to disable the external device monitoring function, connect the auxiliary output and external device monitoring input. At such times, do not connect a load to the auxiliary output. 2 (Orange) (Yellow-green) K1 * S1 Emitter MEASUREMENT SENSORS (Orange / Black) (Brown) Construct the interlock (reset input) circuit separately. Notes: 1) Unused wires must be insulated to ensure that they do not come into contact with wires already in use. 2) Vs is the applying supply voltage. PARTICULAR USE SENSORS SIMPLE WIRE-SAVING UNITS 1 3 INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS 4 Internal circuit Receiver (Pink) * S1 (Shield) Load MICRO PHOTOELECTRIC SENSORS PRESSURE / FLOW SENSORS (Brown) (Yellow-green / Black) 2 1 (Shield) 8 (Blue) 0 V 7 PHOTOELECTRIC SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS 1 4 (Orange) Synchronization + (Orange / Black) Synchronization – Users’ circuit (Orange / Black) Synchronization – 6 (Orange) Synchronization + 5 (Brown) +V Sensor circuit Receiver Load LASER SENSORS AREA SENSORS 7 5 Emitter * S1 60 mA max. + 616 Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C 2 1 3 SF4C 8 4 7 5 6 BSF4-AH80 Cable color: Gray with black line (Orange / Black) SF2B (Orange) SF2C (Brown) Definition of Sensing Heights (Yellow-green) (Black) (White) (Shield) (Blue) K1 Load K1: External device (Force-guided relay or magnet contactor) Note: U  nused wires must be insulated to ensure that they do not come into contact with wires already in use. 617 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Safety Light Curtain Type 2 I/O CIRCUIT AND WIRING DIAGRAMS SF-C11 SF2B series wiring diagram (Control category 2) • Set the safety light curtain input polarity selection switch to the NPN side and ground the + side. Safety light curtain input polarity selection switch STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS A1 F.G. Receiver side connector Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights F Ui SF-C11 control circuit L1 FUSE1 13 23 NPN PNP FUSE2 Terminal arrangement diagram 33 41 Terminal K1 A1 A2 K2 Emitter side connector OUT A2 AUX 0V T2 TEST (Note 3) INTER_LOCK 13 FAULT 14 T1 14 24 34 42 KA, KB: Force-guided relay or KB magnet contactor KA N L1 L2 L3 KB KA 23 X1 X2 X3 A B T1 T2 AUX 24 33 34 41 M 3 42 Notes: 1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentary-type switch as the reset (RESET) button. 3) Emission halt occurs when the test (TEST) button is open, and emission occurs when the test (TEST) button is short-circuited. If not using the test (TEST) button, short-circuit T1 and T2. However, use a test rod or similar to interrupt the light in order to carry out self-diagnosis separately. Function A1 +24 V DC A2 0V 13-14, 23-24, 33-34 Safety output (NO contact × 3) 41-42 Auxiliary output (NC contact × 1) X1 Reset output terminal X2 Reset input terminal (Manual) X3 Reset input terminal (Automatic) A Not used B For PNP output (minus ground) T1 Test output terminal T2 Test input terminal AUX Semiconductor auxiliary output • Set the safety light curtain input polarity selection switch to the PNP side and ground the 0 V line. Safety light curtain input polarity selection switch +24 V DC A1 Receiver side connector RESET (Note 1) (Note 1, 2) X1 X2 X3 A B F Ui SF-C11 control circuit FUSE1 13 23 NPN PNP Pin layout for safety light curtain connectors L1 FUSE2 2 33 41 Emitter side connector A2 OUT AUX 0V T2 TEST (Note 3) INTER_LOCK 1 3 7 6 4 FAULT 14 24 34 42 T1 KA, KB: Force-guided relay or KB magnet contactor KA N Connector pin No. 8 K1 5 K2 F.G. Selection Guide RESET (Note 1) (Note 1, 2) X1 X2 X3 A B +24 V DC SIMPLE WIRE-SAVING UNITS MEASUREMENT SENSORS Be sure to use the following mating cables when connecting SF-C11 to SF2B series. SF2B-CB05 (cable length: 0.5 m 1.640 ft) SF2B-CB5 (cable length: 5 m 16.404 ft) SF2B-CB10 (cable length: 10 m 32.808 ft) SFB-CCJ10E (for emitter, cable length: 10 m 32.808 ft) SFB-CCJ10D (for receiver, cable length: 10 m 32.808 ft) For NPN output (plus ground) SENSOR OPTIONS WIRE-SAVING SYSTEMS SF2B SERIES Ver.2 L1 L2 L3 KB KA M 3 Notes: 1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentary-type switch as the reset (RESET) button. 3) Emission halt occurs when the test (TEST) button is open, and emission occurs when the test (TEST) button is short-circuited. If not using the test (TEST) button, short-circuit T1 and T2. However, use a test rod or similar to interrupt the light in order to carry out self-diagnosis separately. Emitter side connector Receiver side connector 1 Not used OSSD2 2 +24 V DC +24 V DC 3 Emission halt OSSD1 4 Auxiliary output EDM (External relay monitor) 5 Synchronization wire + Synchronization wire + 6 Synchronization wire – Synchronization wire – 7 0V 0V 8 Shield wire Shield wire Safety Light Curtain Type 2 SF2B SERIES Ver.2 I/O CIRCUIT AND WIRING DIAGRAMS 618 FIBER SENSORS LASER SENSORS SF-C13 PHOTOELECTRIC SENSORS SF2B series wiring diagram (Control category 2) Terminal arrangement diagram NPN output type • Connect the safety light curtain control outputs OSSD 1 and OSSD 2 to S4 and S2 respectively and ground the + side. Emitter Receiver Cable color: Gray with black line Cable color: Gray (Orange) Synchronization + +V (Brown) +24 V DC (Orange / Black) Synchronization – Shield Test input Auxiliary output (Pink) (Yellow-green / Black) 0V Load (Blue) Shield +V (Brown) 0 V (Blue) External device monitoring input (Yellow-green) OSSD 2 (White) OSSD 1 (Black) A1 A2 S1 S2 S3 S4 AUX X1 X2 X3 13 14 23 24 33 34 41 42 Terminal Function A1 +24 V DC A2 0V S1 to S4 Safety light curtain control output (OSSD) input terminal AUX Semiconductor auxiliary output X1 Reset output terminal X2 Reset input terminal (Manual) X3 Reset input terminal (Automatic) 13-14, 23-24, 33-34 Safety output (NO contact × 3) 41-42 Auxiliary output (NC contact × 1) L1 (Note 1) FUSE1 A1 F.G. S1 S2 S3 S4 X1 X2 X3 13 23 F FUSE2 33 41 RESET (Note 1, 2) K1 Ui Use a separate terminal block to carry out wiring for safety light curtains that cannot be connected to the SF-C13. K2 A2 AUX 0V INTER_LOCK 14 24 34 42 KA, KB: Force-guided relay or KB magnet contactor KA N L1 L2 L3 KB KA M 3 Notes: 1) The left diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentary-type switch as the reset (RESET) button. Auxiliary output (Yellow-green / Black) +V (Brown) Load (Note 1) FUSE1 S4 X1 X2 F SF4B-C SF4C X3 13 23 BSF4-AH80 FUSE2 SF2B 33 41 SF2C K1 Definition of Sensing Heights K2 0V AUX F.G. ENERGY MANAGEMENT SOLUTIONS SF4B/ SF4B-G SF-C13 control circuit A2 HUMAN MACHINE INTERFACES SF4D L1 OUT STATIC CONTROL DEVICES Safety Components Shield 0 V (Blue) RESET (Note 1, 2) Ui MEASUREMENT SENSORS Safety Control Units OSSD 1 (Black) S2 S3 WIRE-SAVING SYSTEMS Safety Light Curtains OSSD 2 (White) S1 SIMPLE WIRE-SAVING UNITS Selection Guide External device monitoring input (Yellow-green) A1 SENSOR OPTIONS UV CURING SYSTEMS (Orange / Black) Synchronization – 0V (Blue) PARTICULAR USE SENSORS Receiver Cable color: Gray with black line Cable color: Gray Test input (Pink) INDUCTIVE PROXIMITY SENSORS MACHINE VISION SYSTEMS (Orange) Synchronization + Shield PRESSURE / FLOW SENSORS FA COMPONENTS • Connect the safety light curtain control outputs OSSD 1 and OSSD 2 to S1 and S2 respectively. +V (Brown) +24 V DC SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PLC FAULT PNP output type Emitter AREA SENSORS LASER MARKERS SF-C13 control circuit OUT MICRO PHOTOELECTRIC SENSORS INTER_LOCK FAULT 14 24 KA, KB: Force-guided relay or magnet contactor KA N 34 42 L1 L2 L3 KB KB KA M 3 Notes: 1) The left diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentary-type switch as the reset (RESET) button. SF2B SERIES Ver.2 LASER SENSORS • This safety light curtain is a Type 2 electrosensitive protective equipment. It is specified that this safety light curtain be utilized only within systems implementing control categories 2, 1 and B (safety-related categories for control systems), as determined by ISO 13849-1. This safety light curtain must never be utilized in any system that requires the usage of category 4 equipment, such as press machines; nor for systems requiring category 3 equipment. • To use this product in the U.S.A., refer to OSHA 1910.212 and OSHA 1910.217 for installation, and in Europe, refer to EN ISO 13855 as well. Observe your national and local requirements before installing this product. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS • Make sure to carry out the test run before regular operation. • This safety system is for use only on machinery in which the dangerous parts can be stopped immediately, either by an emergency stop unit or by disconnecting the power supply. Do not use this system with machinery which cannot be stopped at any point in its operation cycle. Self-diagnosis function • This safety light curtain incorporates the self-diagnosis function. In case an abnormality is detected during self-diagnosis, the safety light curtain is put in the lockout state at that instant, and the control output (OSSD 1, OSSD 2) is fixed at the OFF state. Refer to “Troubleshooting” (p.623) and the instruction manual and remove the cause of the abnormality. • In order to maintain safe condition of safety light curtain, inspect the beam interrupted status of the device once a day or more. Failure to do so could delay the detection of unexpected abnormality and increase the degree of hazard, which may cause the malfunction of safety light curtain, resulting in serious body injury or death. • In order to check all abnormalities in the OSSD 1, OSSD 2 and auxiliary output, the beam interrupted status of device must be checked. Perform either of two below to inspect the device under beam interrupted status. • Emission halt by test input (Emission halt function) • Beam interrupting by test rod (Excluding the cable SF2B-CB05-A) Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 20 ms or less 20 ms or less 20 ms or less Short-circuited Test input Open When using the SF2B-CB05-B Short-circuited Emission status 20 ms or less Emission Emission halt 40 to 60 ms 15 ms or less Control outputs ON (OSSD 1, OSSD 2) OFF Do not use the emission halt function (test input) for the purpose of stopping the device. Failure to do so could result in serious injury or death. Auxiliary output • This catalog is a guide to select a suitable product. Be sure to read instruction manual prior to its use. • Both emitter and receiver are adjusted before shipment, please apply both emitter and receiver with the same serial No. The serial No. is indicated on the plates of both emitter and receiver. (Indicated under the model No.) UV CURING SYSTEMS SF4C Open Emission halt function (Test input) • This function stops the emission process of the emitter. You can select whether emission is on or halted by means of the connection status for the test input (pink). Test input Open Connected to 0 V or +V • Auxiliary output is incorporated into the emitter and its operation varies depending on the type of bottom cap cable (optional) to be used. Normal mode Bottom cap cable When using the SF2B-CB05-B Emission Emission Emission halt • During emission halt, the control outputs (OSSD 1, OSSD 2) become OFF status. • By using this function, malfunction due to extraneous noise or abnormality in the control outputs (OSSD 1, OSSD 2) and the auxiliary output can be determined even from the machinery side. Lockout Beam received Beam interrupted When using the SF2B-CCB□ / SF2B-CB□ ON OFF ON ON When using the SF2B-CB05-A OFF ON ON OFF SF2B-CB05-B Cannot be used. When bottom cap cable SF2B-CCB□ or SF2B-CB□ (optional) is used • The auxiliary output is incorporated in the emitter. It is OFF when the control outputs (OSSD 1,OSSD 2) are ON and vice versa. • The auxiliary output can be used as an operation monitor of the device. • When the external device monitor function is not used, connect the external device monitor input line to the auxiliary output line to disable the function. In this case, do not connect the load to the auxiliary output. For details, refer to “External device monitoring function” (p.620) and “ I/O CIRCUIT AND WIRING DIAGRAMS” (p.615~). • When the external device monitoring function is used to disable, do not directly use the auxiliary output as the operation monitor of this safety light curtain. When the external device monitor is used to disable and the auxiliary output is used to monitor the operation of safety light curtain, connect the auxiliary output and the external device monitoring input to the external relay (purchase separately) to use the external relay contacting point as an operation monitor of this safety light curtain. Emission status Emission halt Control outputs Emission (OSSD 1, OSSD 2) status halt Receiver WIRE-SAVING SYSTEMS Test input External device monitoring input (Yellow-green) SIMPLE WIRE-SAVING UNITS Refer to the instruction manual for details. The instruction manual can be downloaded from our website. PRECAUTIONS FOR PROPER USE Emitter FIBER SENSORS Safety Light Curtain Type 2 Auxiliary output (Yellow-green / Black) 619 Use as operation monitoring External relay (Purchase separately.) Connect NPN output type to +V and connect PNP output type to 0 V Connect NPN output type to 0 V and connect PNP output type to +V Safety Light Curtain Type 2 PRECAUTIONS FOR PROPER USE Beam received Beam received condition Beam interrupted Control outputs (OSSD 1, OSSD 2) 40 to 60 ms OFF 20 ms or less 20 ms or less OFF When bottom cap cable SF2B-CB05-A (optional) is used Make sure to use the auxiliary output when using the bottom cap cable SF2B-CB05-A (optional). Set the device so the control machine can be stopped when either the control output (OSSD 1) or auxiliary output turns to OFF. If the auxiliary output is should not be used, the device cannot stop operation when an unexpected error occurs during control output (OSSD 1) failure, which may result in serious injury or death. • The auxiliary output is incorporated in the emitter. It outputs ON at the normal operation of device. It outputs OFF in the following cases: • When an abnormality which needs emission halt status occurs [for example, the control output (OSSD 1) shortcircuit and an error occurs.] • While test input has been input • The error cannot be transmitted to the control machine. The alarm signal is output from the auxiliary output. Control output (OSSD1) Auxiliary output Control output (OSSD1) short-circuited ON OFF Beam received Beam received condition Beam interrupted Control outputs (OSSD 1, OSSD 2) ON ON Auxiliary output 15 ms or less OFF When bottom cap cable SF2B-CB05-B (optional) is used • The auxiliary output cannot be utilized by using the bottom cap cable SF2B-CB05-B (optional). External device monitoring function • This function is available when the bottom cap cable SF2B-CCB□ or SF2B-CB□ (optional) is used. This is the function for checking whether the external safety relay connected to the control outputs (OSSD 1, OSSD 2) performs normally in accordance with the control outputs (OSSD 1, OSSD 2) or not. Monitor the b contact of the external safety relay, and if any abnormality such as deposit of the contacting point, etc. is detected, change the status of the safety light curtain into lockout one, and turn OFF the control outputs (OSSD 1, OSSD 2). In case of setting the external device monitoring function to enabled • Connect the external device monitoring input (yellow-green) to the b contact of the external safety relay that is connected to the control outputs (OSSD 1, OSSD 2). 300 ms or less OFF • The time set for external device monitoring is 300 ms or less. Exceeding 300 ms turns the safety light curtain into lockout condition. Beam received Beam received condition Beam interrupted Control outputs ON (OSSD 1, OSSD 2) OFF ON External device monitoring input Lockout condition SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS 40 to 60 ms MEASUREMENT SENSORS ON Control outputs (OSSD 1, OSSD 2) OFF STATIC CONTROL DEVICES 300 ms ON OFF Lockout condition LASER MARKERS PLC • This is the configuration for connecting multiple sets of emitters and receivers facing each other in series. It is used when the dangerous part can be entered from two or more directions. The control outputs (OSSD 1, OSSD 2) turns OFF if any of the safety light curtain is interrupted. For details, refer to the instruction manual. Notes 1): Series connection connectors cannot be used with the SF2B-H8-□ and SF2B-A4-□, and so series connection is not possible. The SF2B-H8SL and SF2B-A4SL are not equipped with series connection connectors, so when connecting three sets in series, they cannot be used in the middle position. 2): The total number of beam axes for the SF2B-A□ is a maximum of 96 when two sets are connected, and 64 when three sets are connected. When SF2B-H□ and SF2B-A□ are combined in series connection, double the number of the beam channels of SF2B-A□ to calculate the total number of beam channels, which should be 128 or less. Example: The total no. of beam channels for SF2B-H36 and SF2B-A44 is 124. The no. of beam channels of SF2B-H36 + (the No. of beam channels of SF2B-A44 × 2) = Total no. of beam channels 36 beam channels + (44 beam channels × 2) = 124 beam channels For serial connections, connect the emitter and receiver of the safety light curtain to the emitter and receiver respectively of the sub-sensors for series connection using the SF2B-CSL□ special series connection cables. Wrong connection could generate the nonsensing area, resulting in serious injury or death. HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C Emitter 3 Receiver 3 Receiver 2 Sub-sensor for series connection only SF2B-□SL (Optional) SF2B-H8SL and SF2B-A4SL cannot be used. Receiver 1 Cable for series connection SF2B-CSL□ (Optional) Emitter 2 SF4C Sub-sensor for series connection only SF2B-□SL (Optional) SF2B-H8SL and SF2B-A4SL can be used. Emitter 1 Receiver AREA SENSORS SENSOR OPTIONS 300 ms Beam received Beam received condition Beam interrupted • Connect the external device monitoring input (yellowgreen) to the auxiliary output (yellow-green / black). External device monitoring input (Yellow-green) MICRO PHOTOELECTRIC SENSORS PARTICULAR USE SENSORS External device monitoring input PHOTOELECTRIC SENSORS INDUCTIVE PROXIMITY SENSORS 15 ms or less OFF In case of not using the external device monitoring function Emitter 300 ms or less ON External device monitoring input Connectable up to 3 sets of safety light curtains (however, 128 beam channels max.) (Note 1, 2) ON Auxiliary output (Yellow-green / Black) 40 to 60 ms ON OFF FIBER SENSORS LASER SENSORS 15 ms or less Series connection Beam interrupted 620 Refer to the instruction manual for details. The instruction manual can be downloaded from our website. SF2B SERIES Ver.2 Synchronization + (Orange) Synchronization – (Orange / Black) Safety light curtain SF2B-H8-□ and SF2B-A4-□ cannot be used. * When using the SF2B-CB05-B, set the frequency selection switches (for both emitter and receiver) to “1”. BSF4-AH80 SF2B SF2C Definition of Sensing Heights Series and parallel mixed connection • Up to a maximum of two sets can be connected in parallel only when using the SF2B-CB05-B adapter cable (optional). For details, refer to the instruction manual. Safety light curtain SF2B-H8-□ and SF2B-A4-□ cannot be used * Set the frequency selection switches (for both emitter and receiver) to “1” at the master units, and set them to “2” at the slave units. SENSOR OPTIONS Interference prevention *S  et the frequency selection switches (for both emitter and receiver) to “1” at the master units, and set them to “2” at the slave units. SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Receiver 3 PARTICULAR USE SENSORS Interference prevention Cable for series connection SF2B-CSL□ (Optional) Receiver 3 Sub-sensor for serial connection only SF2B-□SL (Optional) PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Receiver 2 Emitter 1 SAFETY LIGHT CURTAINS / SAFETY COMPONENTS Receiver 1 AREA SENSORS • Up to a maximum of three sets can be connected in a mixture of series and parallel (for a total maximum number of 128 beam channels. However, the total number of beam channels for the SF2B-A□ is a maximum of 96 when two sets are connected, and 64 when three sets are connected.) only when using the SF2B-CB05-B adapter cable (optional). For details, refer to the instruction manual. Emitter 2 MICRO PHOTOELECTRIC SENSORS Parallel connection Receiver 2 PHOTOELECTRIC SENSORS Refer to the instruction manual for details. The instruction manual can be downloaded from our website. PRECAUTIONS FOR PROPER USE Emitter 2 LASER SENSORS SF2B SERIES Ver.2 Receiver 1 FIBER SENSORS Safety Light Curtain Type 2 Emitter 1 621 Part description and function Top end Emitter Receiver A Beam-axis alignment indicator [RECEPTION] Emission halt indicator [HALT] Beam-axis alignment indicator [RECEPTION] C D Operation indicator [OPERATION] A B Beam-axis alignment indicator [RECEPTION] Fault indicator [FAULT] A B C D B OSSD indicator [OSSD] C Incident light intensity indicator [STB] D Fault indicator [FAULT] Digital error indicator Setting indicator [SETTING] FA COMPONENTS Frequency selection switch MACHINE VISION SYSTEMS UV CURING SYSTEMS Description Selection Guide Safety Control Units Safety Components Beam-axis alignment indicator (Red / Green) [RECEPTION] B C SF4D D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 1 Function A Safety Light Curtains 2 When all beam channels of safety light curtain top are receiving light: lights up in red When safety light curtain top end receives light: blinks in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green (always off when using the SF2B-CB05-B) When all beam channels of safety light curtain upper middle are receiving light: lights up in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green (always off when using the SF2B-CB05-B) When all beam channels of safety light curtain lower middle are receiving light: lights up in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green (always off when using the SF2B-CB05-B) When all beam channels of safety light curtain bottom are receiving light: lights up in red When sensor bottom end receives light: blinks in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green (always off when using the SF2B-CB05-B) When control outputs (OSSD 1, OSSD 2) are OFF: lights up in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green When using the SF2B-CB05-B When fault occurs in the emitter: light up in red When emitter is normal: light up in green Bottom end Description Function A Beam-axis alignment indicator (Red / Green) [RECEPTION] B C D OSSD indicator (Red / Green) [OSSD] When all beam channels of safety light curtain top are receiving light: lights up in red When sensor top end receives light: blinks in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green When all beam channels of safety light curtain upper middle are receiving light: lights up in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green When all beam channels of safety light curtain lower middle are receiving light: lights up in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green When all beam channels of safety light curtain bottom are receiving light: lights up in red When sensor bottom end receives light: blinks in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green When control outputs (OSSD 1, OSSD 2) are OFF: lights up in red When control outputs (OSSD 1, OSSD 2) are ON: lights up in green Setting indicator (Red) [SETTING] Always off When using the SF2B-CB05-B One lights up when set to Frequency 1 Two light up when set to Frequency 2 When sufficient light is received (incident light intensity: 130 % or more) (Note 1): lights up in green When stable light is received (incident light intensity: 115 to 130 %) (Note 1): OFF When unstable light is received (incident light intensity: 100 to 115 %) (Note 1): lights up in orange When light is interrupted: OFF (Note 2) Fault indicator (Yellow) [FAULT] When fault occurs in the sensor: lights up or blinks When device is lockout: lights up for malfunction content When using the SF2B-CB05-B Digital error indicator Display shows fault contents during lockout. (Red)(Note 3) Center lights up when set to Frequency 1 Center and bottom lights up when set to Frequency 2 Frequency selection switch Used for switching between master and slave when using the SF2B-CB05-B. Set to “1” for master and “2” for slave. Frequency selection switch Operation indicator (Red / Green) [OPERATION] Emission halt indicator When light emission is halt: lights up (Orange) [HALT] When light is emitted: lights off Fault indicator (Yellow) [FAULT] When fault occurs in the sensor: lights up or blinks Incident light intensity indicator (Orange / Green) [STB] Used for switching between master and slave when using the SF2B-CB05-B. Set to “1” for master and “2” for slave. Notes: 1) The threshold value where the control output changes from OFF to ON is applied as “100 % incident light intensity”. 2) The status “when light is interrupted” refers to the status that the some obstacle is existed in the sensing area. 3) For details, refer to “Troubleshooting” (p.623) and the instruction manual. 4) The description given in [ ] is marked on the safety light curtain. Safety Light Curtain Type 2 PRECAUTIONS FOR PROPER USE SF2B SERIES Ver.2 622 Refer to the instruction manual for details. The instruction manual can be downloaded from our website. Wiring FIBER SENSORS LASER SENSORS Refer to the applicable regulations for the region where this safety light curtain is to be used when setting up the safety light curtain. In addition, make sure that all necessary measures are taken to prevent possible dangerous operating errors resulting from earth faults. • Make sure to carry out the wiring in the power supply off condition. • Verify that the supply voltage variation is within the rating. • If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. • In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground. • Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. Others Dangerous part of machine Emitter S Sensing area (Beam axis) Receiver S: Safety distance • Safety distance is calculated based on the following equation when a person moves perpendicular (normal intrusion) to the sensing area of the safety light curtain. In case the intrusion direction is not perpendicular to the sensing area, be sure to refer to the relevant standard (regional standard, specification of the machine, etc.) for details of the calculation. (Please check the latest standards for the equation.) For use based on EN ISO 13855 / ISO 13855 / JIS B 9715 • This device has been developed / produced for industrial use only. • Do not use during the initial transient time (2 s) after the power supply is switched on. • Avoid dust, dirt and steam. • Take care that the sensor does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. • Take care that the sensor is not directly exposed to fluorescent light from a rapid-starter lamp or a high frequency lighting device, as it may affect the sensing performance. Sensing area • Make sure to install this product such that any part of the human body must pass through its sensing area in order to reach the dangerous parts of the machinery. If the human body is not detected, there is a danger of serious injury or death. • Do not use any reflective type or retroreflective type arrangement. • Emitter and receiver that face each other should be from the same model No. (with same beam axis pitch and number of beam channels) and aligned in the vertical direction. If units from different sets are connected together, it may cause blind spots in the sensing area, and death or serious injury may result. • Do not connect facing several receivers towards one emitter. Example of correct sensing area setup Dangerous part Sensing area Protective structure For intrusion direction perpendicular to the sensing area • Equation 1 S=K×T+C S: Safety distance (mm) Minimum required distance between the sensing area surface and the dangerous parts of the machine K: Intrusion speed of operator’s body or objects (mm/sec.) Normally, taken as SF2B-H□ 2,000 (mm/sec.), SF2B-A□ 1,600 (mm/sec.) for calculation. T: Response time of total equipment (sec.) T = Tm + TSF2B Tm: Maximum halting time of machinery (sec.) TSF2B: Response time of the SF2B series 0.015 (sec.) C: Additional distance calculated from the size of the minimum sensing object of the safety light curtain (mm) However, the value of “C” cannot be 0 or less. C = 8 × (d – 14) d: Minimum sensing object diameter SF2B-H□: d= 27 (mm) 1.063 (in), C = 104 (mm) 4.094 (in) For SF2B-A□, C = 850 (mm) 33.465 (in) (constant) • For calculating the safety distance “S”, there are the following five cases. First calculate by substituting the value K = 2,000 (mm/sec.) in the equation above. Then, classify the obtained value of “S” into three cases, 1) S < 100, 2) 100 ≤ S ≤ 500, and 3) S > 500. For Case 3) S > 500, recalculate by substituting the value K = 1,600 (mm/sec.). After that, classify the calculation result into two cases, 4) S ≤ 500 and 5) S > 500. For details, refer to the instruction manual. For use based on ANSI B11.19 Dangerous part Sensing area Example of incorrect sensing area setup Sensing area Dangerous part Dangerous part Sensing area Safety distance • Calculate the safety distance correctly, and always maintain a distance which is equal to or greater than the safety distance, between the sensing area of this safety light curtain and the dangerous parts of the machinery. (Please check the latest standards for the equation.) If the safety distance is miscalculated or if sufficient distance is not maintained, there is a danger of serious injury or death. • Before designing the system, refer to the relevant standards of the region where this device is to be used and then install this device. • Equation 2 S = K × (Ts + Tc + TSF2B + Tbm) + Dpf S: Safety distance (mm) Minimum required distance between the sensing area surface and the dangerous parts of the machine K: Intrusion velocity {Recommended value in OSHA is 63 (inch/sec.) ≈ 1,600 (mm/sec.)} ANSI B11.19 does not define the intrusion velocity “K”. When determining K, consider possible factors including physical ability of operators. Ts: Halting time calculated from the operation time of the control element (air valve, etc.) (sec.) Tc: Maximum response time of the control circuit required for functioning the brake (sec.) TSF2B: Response time of safety light curtain 0.015 (sec.) Tbm: Additional halting time tolerance for the brake monitor (sec.) Tbm = Ta – (Ts + Tc) Ta: Setting time of brake monitor (sec.) When the machine is not equipped with a brake monitor, it is recommended that 20 % or more of (Ts + Tc) is taken as additional halting time. Dpf: Additional distance calculated from the size of the minimum sensing object of the safety light curtain SF2B-H□ Dpf = 2.676 (inch) ≈ 68 (mm) SF2B-A□ Dpf = 5.355 (inch) ≈ 136 (mm) Dpf = 3.4 × (d – 0.276) (inch) Dpf ≈ 3.4 × (d – 7) (mm) d: Minimum sensing object diameter 1.063 (inch) ≈ 27 (mm) SF2B-H□ Minimum sensing object diameter 1.851 (inch) ≈ 47 (mm) SF2B-A□ PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 623 Influence of reflective surfaces PHOTOELECTRIC SENSORS Install the safety light curtain by considering the effect of nearby reflective surfaces, and take countermeasures such as painting, masking, or changing the material of the reflective surface, etc. Failure to do so may cause the safety light curtain not to detect, resulting in serious body injury or death. MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS • Keep the minimum distance given below, between the safety light curtain and a reflective surface. Side view Emitter Sensing area L SIMPLE WIRE-SAVING UNITS Reflective floor STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Distance between emitter and receiver (Setting distance L) Selection Guide Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights Allowable installation distance A 0.2 to 3 m 0.32 m 1.050 ft 0.656 to 9.843 ft L/2 × tan2θ 3 to 13 m 9.843 to 42.651 ft = L × 0.106 (m) 0.348 (ft) (Note 1) (θ = 6°) 6° 6° (Note 2) Receiver L 1.2 3.937 Install in this area 0.6 1.969 All indicators are off. 0 Emitter side Phenomenon Cause Power is not being supplied. Supply voltage is out of the specified range. Connector is not connected securely. Operation indicator The beam channels remains lit up in red the emitter and (beam is not received). of [OPERATION] the receiver are not correctly aligned. Emission is in halt condition. The synchronization wire error The receiver does not work. Emission halt The interference indicator (orange) prevention wire error lights up. When using the [HALT] SF2B-CB05-B: When set to slave Master / slave setting error When using the SF2B-CB05-B: When set to master The master sensor does not work. Fault indicator (yellow) lights up or blinks. [FAULT] [Blinks once] Total safety light curtains No./total beam channel No. error [Blinks twice] Auxiliary output error [Other than the above] Effect from noise / power supply or failure of internal circuit Remedy Check that the power supply capacity is sufficient. Connect the power supply correctly. Provide the supply voltage within the specified range. Connect the connector securely. Align the beam channels. Connect the test input (emission halt input) wire correctly. The logic varies depending on the cable to be used. Connect the synchronization wire correctly. Check the operation of the receiver side. Connect the interference prevention wire correctly. Set the master/slave setting to “master”. Check the master side safety light curtain. Connect the end cap properly. Connect the cable for series connection correctly. Check the model (emitter / receiver) of sub-sensor for series connection. Set the No. of the safety light curtains in series connection, and a total No. of beam channels within the specification. Connect the auxiliary output cable correctly. Check the noise status around this safety light curtains. Check the wiring, supplied voltage and power supply capacity. Even if the error is not eliminated, contact our office. Fault indicator (yellow) lights up or blinks. [FAULT] or Remedy Power is not being supplied. Check that the power supply capacity is sufficient. Connect the power supply correctly. Supply voltage is output of the specified range. Set the supply voltage correctly. Connector is not connected securely. The beam channels of the emitter and the receiver are not correctly aligned. Total unit No./total beam channel No. error Connect the connector securely. Stable indicator The beam channels lights up (Orange) of the emitter and the [STB] receiver are not correctly aligned. Do not install in this area 3 6 9 12 13 9.843 19.685 29.528 39.370 42.651 Distance between emitter and receiver (m ft) Cause OSSD indicator remains lit up in red (beam is not received). The master / slave setting is different. [OSSD] When using with the SF2B-CB05-B 0.3 0.984 Troubleshooting or Phenomenon 0.9 2.953 Notes: 1) If using the SF2B-CB05-B, the operating range is 0.3 to 5 m 0.984 to 16.404 ft. 2) The effective aperture angle for this device is ±5° or less (when L > 3 m 9.843 ft) as required by IEC 61496-2 / UL 61496-2. However, install this device away from reflective surfaces considering an effective aperture angle of ±6° to take care of beam misalignment, etc. during installation. All indicators are off. Safety Light Curtains A 1.5 4.921 A WIRE-SAVING SYSTEMS MEASUREMENT SENSORS Reflective surface A Emitter SENSOR OPTIONS Receiver side Top view Reflective ceiling INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Refer to the instruction manual for details. The instruction manual can be downloaded from our website. PRECAUTIONS FOR PROPER USE Allowable installation distance A (m ft) LASER SENSORS SF2B SERIES Ver.2 Receiver FIBER SENSORS Safety Light Curtain Type 2 Align the beam channels. Set the same value to the Nos. of emitter and receiver. Set the setting identically. Align the beam channels. [Digital error indicator ] Total safety light curtain No./total beam channel No. error Connect the end cap properly. Connect the cable for series connection correctly. Check the model (emitter / receiver) of sub sensor for series connection. Check that the number of safety light curtains / number of beam axes is within the specification value. [Digital error indicator ] Control outputs (OSSD 1, OSSD 2) error Connect the control outputs (OSSD1, OSSD2) correctly. [Digital error indicator ] Extraneous light error Prevent any extraneous light from entering the receiver. [Digital error indicator ] External device monitoring error Connect the external device monitor input wire correctly. Replace the replay unit. Replace the relay unit having appropriate response time. [Digital error indicator ] Bottom connector error Check the type of the bottom connector. Cable of the emitter: Gray (with black stripe) [Other than the above] Effect from noise / power supply or failure of internal circuit Check the noise status around this safety light curtain. Check the wiring, supplied voltage and power supply capacity. Even if the error is not eliminated, contact our office. Corner mirror • Be sure to carry out maintenance while referring to the instruction manual for the SF2B series of safety light curtains. • Do not use if dirt, water, or oil, etc. is attached to the reflective surface of this product. Appropriate sensing range may not be maintained due to diffusion or refraction. • Make sure that you have read the instruction manual for the corner mirror thoroughly before setting up the corner mirrors and safety light curtains, and follow the instructions given. If the equipment is not set up correctly as stipulated in the instruction manual, incident light errors may result in unexpected situations which may result in serious injury or death. • Please download the instruction manuals from our website. • Safety light curtain SF2B series cannot be used as a retroreflective type. Avoid installing the safety light curtain as a retroreflective type when this product is applied. • The mirror part of this product is made of glass. Note that if it is broken, the glass shards may fly apart. Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) SF2B SERIES Ver.2 624 The CAD data can be downloaded from our website. SF2B-□  SF2B-□SL LASER SENSORS Safety light curtain, Sub-sensor for series connection only PHOTOELECTRIC SENSORS Assembly dimensions Mounting drawing for the safety light curtains using the standard mounting brackets MS-SF2B-1 (optional) and the intermediate supporting brackets MS-SF2B-2 (accessory for safety light curtain). 53 2.087 Standard mounting bracket MS-SF2B-1 (Optional) 28 1.102 18 0.709 5.5 0.217 2.5 0.098 5 0.197 End cap J 28 1.102 (Note 2) 26 1.024 26 1.024 24 0.945 28 1.102 18 0.709 5.5 0.217 2.5 0.098 24 0.945 41 1.614 5 0.197 20 0.787 28 1.102 24 0.945 ABC CBA 20 0.787 F 20 0.787 5.5 0.217 E Beam pitch 5 0.197 D 30.5 1.201 AREA SENSORS 41 1.614 5 0.197 J 28 1.102 24 0.945 INDUCTIVE PROXIMITY SENSORS 20 0.787 20 0.787 G G H H Emitter Bottom cap cable 20 0.787 20 0.787 F 20 0.787 5.5 0.217 E D Beam pitch 5 0.197 G 32.5 1.280 Receiver 20 0.787 5.5 0.217 E H 5 0.197 G 32.5 1.280 H Bottom cap cable Emitter D Receiver Notes: 1) The MS-SF2B-2 intermediate supporting bracket is provided as an accessory with this product. The number of accessories provided varies depending on the product. 2) An end cap (connector for series connection) is not provided for the SF2B-H8(SL)(-□) and SF2B-A4(SL)(-□). A B C D E F Model No. G H J (Note) SF2B-A4(SL)(-□) 168 6.614 207 8.150 223 8.780 – – – SF2B-H□ 20 0.787 6 0.236 6 0.236 SF2B-H12(SL)(-□) SF2B-A6(SL)(-□) 232 9.134 270 10.630 286 11.260 – – – SF2B-A□ 40 1.575 26 1.024 6 0.236 SF2B-H16(SL)(-□) SF2B-A8(SL)(-□) 312 12.283 350 13.780 366 14.409 – – – SF2B-H20(SL)(-□) SF2B-A10(SL)(-□) 392 15.433 430 16.929 446 17.559 – – – SF2B-H24(SL)(-□) SF2B-A12(SL)(-□) 472 18.583 510 20.079 526 20.709 – – – SF2B-H28(SL)(-□) SF2B-A14(SL)(-□) 552 21.732 590 23.228 606 23.858 – – – SF2B-H32(SL)(-□) SF2B-A16(SL)(-□) 632 24.882 670 26.378 686 27.008 – – – SF2B-H36(SL)(-□) SF2B-A18(SL)(-□) 712 28.031 750 29.528 766 30.157 – – – SF2B-H40(SL)(-□) SF2B-A20(SL)(-□) 792 31.181 830 32.677 846 33.307 390 15.354 – – SF2B-H48(SL)(-□) SF2B-A24(SL)(-□) 952 37.480 990 38.976 1,006 39.606 470 18.504 – – SF2B-H56(SL)(-□) SF2B-A28(SL)(-□) 1,112 43.779 1,150 45.276 1,166 45.905 550 21.654 – – SF2B-H64(SL)(-□) SF2B-A32(SL)(-□) 1,272 50.079 1,310 51.575 1,326 52.205 418 16.457 842 33.150 – SF2B-H72(SL)(-□) SF2B-A36(SL)(-□) 1,432 56.378 1,470 57.874 1,486 58.504 472 18.583 948 37.323 – SF2B-H80(SL)(-□) SF2B-A40(SL)(-□) 1,592 62.677 1,630 64.173 1,646 64.803 525 20.669 1,055 41.535 – SF2B-H88(SL)(-□) SF2B-A44(SL)(-□) 1,752 68.976 1,790 70.472 1,806 71.102 433 17.047 870 34.252 1,308 51.496 SF2B-H96(SL)(-□) SF2B-A48(SL)(-□) 1,912 75.275 1,950 76.772 1,966 77.401 473 18.622 950 37.402 1,428 56.220 Model No. SF2B-H8(SL)(-□) SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS F 5 0.197 D 30.5 1.201 PARTICULAR USE SENSORS SENSOR OPTIONS A CB BC A SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Protective height F E 10.5 0.413 18 0.709 5.5 14 0.217 0.551 22.5 0.886 22.5 0.886 28 1.102 28 1.102 Protective height 20 0.787 20 0.787 5.5 0.217 5 0.197 10.5 0.413 18 0.709 5.5 14 0.217 0.551 J J 28 1.102 20 0.787 Intermediate supporting bracket MS-SF2B-2 (Note 1)(Accessory) MICRO PHOTOELECTRIC SENSORS 53 2.087 FIBER SENSORS Note: T  he distance between the tip of the safety light curtain and the last beam axis of the  SF2B-H8(SL)(-□) and SF2B-A4(SL)(-□) is 22 mm 0.866 in. MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Safety Light Curtains Safety Control Units Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights 625 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Safety light curtain, Sub-sensor for series connection only Assembly dimensions Mounting drawing for the safety light curtains using the dead zoneless mounting brackets MS-SF2B-3 (optional) and the intermediate supporting brackets MS-SF2B-2 (accessory for safety light curtain). End cap (Note 2) 53 2.087 50 1.969 Dead zoneless mounting bracket MS-SF2B-3 (Optional) 1.7 0.067 Intermediate supporting bracket MS-SF2B-2 Dead zoneless mounting bracket (Note 1) (Accessory) MS-SF2B-3 Spacer for intermediate supporting bracket (Optional) (Accessory for MS-SF2B-3) 50 1.7 0.067 1.969 End cap 41 1.614 (Note 2) 53 2.087 50 1.969 1.7 0.067 J 54 2.126 J 24 0.945 41 1.614 28 1.102 28 1.102 A K 20 0.787 24 0.945 1.3 0.051 3 54 0.118 2.126 G G 6.5 0.256 5.5 0.217 Bottom 30.5 cap cable 1.201 (Optional) Beam H pitch 19 0.748 24 26 0.945 1.024 3 0.118 54 2.126 5.5 0.217 H 19 0.748 30.5 1.201 26 24 1.024 0.945 Emitter 54 2.126 6.5 0.256 5.5 0.217 6.5 0.256 3 0.118 26 1.024 Q P 5.5 0.217 3 0.118 1.3 0.051 P 27.1 1.067 1.1 0.043 31.3 1.232 Bottom cap cable (Optional) 2 (0.079 ) 2 (0.079 ) 1.1 H 0.043 31.3 1.232 1.1 (0.043 ) Receiver 54 2.126 5.5 0.217 16.5 0.650 6.5 0.256 26 1.024 1.1 (0.043 ) 27.1 1.067 27.1 1.067 Emitter 3 0.118 G G Beam pitch H 16.5 0.650 24 0.945 5.5 0.217 41 1.614 Q 3 0.118 K 5 R 0.197 41 1.614 5.5 0.217 L L 5 0.197 R 5.5 0.217 M 5 0.197 28 1.102 41 A A 41 1.614 1.614 20 0.787 N 5.5 0.217 5 0.197 41 1.614 Protective height K KA 20 0.787 20 0.787 5.5 0.217 27.1 1.067 54 2.126 J 20 0.787 Protective 28 height 1.102 M J 24 0.945 20 0.787 N 54 2.126 54 2.126 50 1.969 1.7 0.067 41 1.614 4 4 (0.157 ) (0.157 ) Intermediate supporting bracket MS-SF2B-2 (Note 1)(Accessory) LASER MARKERS PLC The CAD data can be downloaded from our website. SF2B-□  SF2B-□SL PARTICULAR USE SENSORS SENSOR OPTIONS SF2B SERIES Ver.2 Receiver Notes: 1) The MS-SF2B-2 intermediate supporting bracket is provided as an accessory with this product. The number of accessories provided varies depending on the product. 2) An end cap (connector for series connection) is not provided for the SF2B-H8(SL)(-□) and SF2B-A4(SL)(-□). Selection Guide Safety Light Curtains Model No. L M N P Q R SF2B-A4(SL)(-□) 168 6.614 155 6.102 – – – – – – SF2B-H12(SL)(-□) SF2B-A6(SL)(-□) 232 9.134 219 8.622 – – – – – – SF2B-H16(SL)(-□) SF2B-A8(SL)(-□) 312 12.283 299 11.772 – – – – – – SF2B-H20(SL)(-□) SF2B-A10(SL)(-□) 392 15.433 379 14.921 – – – – – – SF2B-H24(SL)(-□) SF2B-A12(SL)(-□) 472 18.583 459 18.071 – – – – – – SF2B-H28(SL)(-□) SF2B-A14(SL)(-□) 552 21.732 539 21.221 – – – – – – SF2B-H32(SL)(-□) SF2B-A16(SL)(-□) 632 24.882 619 24.370 – – – – – – SF2B-H36(SL)(-□) SF2B-A18(SL)(-□) 712 28.031 699 27.520 – – – – – – SF2B-H40(SL)(-□) SF2B-A20(SL)(-□) 792 31.181 779 30.669 390 15.354 – – 379.5 14.941 – – SF2B-H48(SL)(-□) SF2B-A24(SL)(-□) 952 37.480 939 36.969 470 18.504 – – 459.5 18.091 – – SF2B-H56(SL)(-□) SF2B-A28(SL)(-□) 1,112 43.779 1,099 43.268 550 21.654 – – Safety Control Units SF2B-H8(SL)(-□) Safety Components SF4D SF4B/ SF4B-G SF4B-C SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights A K – 539.5 21.240 SF2B-H64(SL)(-□) SF2B-A32(SL)(-□) 1,272 50.079 1,259 49.567 418 16.457 842 33.150 – 407.5 16.043 831.5 32.736 – – SF2B-H72(SL)(-□) SF2B-A36(SL)(-□) 1,432 56.378 1,419 55.866 472 18.583 948 37.323 – 461.5 18.169 937.5 36.909 – SF2B-H80(SL)(-□) SF2B-A40(SL)(-□) 1,592 62.677 1,579 62.165 525 20.669 1,055 41.535 – 514.5 20.256 1,044.5 41.122 – SF2B-H88(SL)(-□) SF2B-A44(SL)(-□) 1,752 68.976 1,739 68.465 433 17.047 870 34.252 1,308 51.496 422.5 16.634 859.5 33.839 1,297.5 51.083 SF2B-H96(SL)(-□) SF2B-A48(SL)(-□) 1,912 75.275 1,899 74.764 473 18.622 950 37.402 1,428 56.220 462.5 18.209 939.5 33.839 1,417.5 55.807 Model No. G H J (Note) SF2B-H□ 20 0.787 6 0.236 6 0.236 SF2B-A□ 40 1.575 26 1.024 6 0.236 Note: T  he distance between the tip of the safety light curtain and the last beam axis of the SF2B-H8(SL)(-□) and SF2B-A4(SL)(-□) is 22 mm 0.866 in. Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) SF2B SERIES Ver.2 The CAD data can be downloaded from our website. RF-SFBH-□ Corner mirror (Optional) 6 17.5 0.236 0.689 18 0.709 6 0.236 t3 t 0.118 26 13 1.024 0.512 t3 t 0.118 Model No. A B C RF-SFBH-8 173 6.811 236 9.291 316 12.441 396 15.591 476 18.740 556 21.890 636 25.039 716 28.189 796 31.339 956 37.638 1,116 43.937 1,276 50.236 1,436 56.353 1,596 62.835 1,756 69.134 1,916 75.433 183 7.205 246 9.685 326 12.835 406 15.984 486 19.134 566 22.283 646 25.433 726 28.583 806 31.732 966 38.031 1,126 44.331 1,286 50.630 1,446 56.929 1,606 63.228 1,766 69.527 1,926 75.827 235 9.252 298 11.732 378 14.882 458 18.031 538 21.181 618 24.331 698 27.480 778 30.630 858 33.779 1,018 40.079 1,178 46.378 1,338 52.677 1,498 58.976 1,658 65.275 1,818 71.575 1,978 77.874 29 1.142 RF-SFBH-12 29 1.142 RF-SFBH-16 RF-SFBH-20 80 3.150 RF-SFBH-24 ø8.5 ø0.335 A B C 18 0.709 6 0.236 6 17.5 0.689 0.236 RF-SFBH-28 F RF-SFBH-32 E 26 13 1.024 0.512 RF-SFBH-36 D RF-SFBH-40 ø8.5 ø0.335 RF-SFBH-48 72 2.835 106 4.173 45° 109 ( 4.219 ) 64 2.520 28 1.102 626 46 1.811 < When mounting at an angle of 45° > 104 ( 4.094 ) 46 (1.811 ) RF-SFBH-56 RF-SFBH-64 RF-SFBH-72 RF-SFBH-80 RF-SFBH-88 RF-SFBH-96 MS-SF2B-1 D E – – – – – – – – – – – – – – – – 458 ± 50 18.031 ± 1.969 538 ± 50 21.181 ± 1.969 618 ± 50 24.331 ± 1.969 698 ± 50 27.480 ± 1.969 538 ± 50 21.181 ± 1.969 591 ± 50 23.268 ± 1.969 645 ± 50 25.394 ± 1.969 698 ± 50 27.480 ± 1.969 – – – – 1,018 ± 50 40.079 ± 1.969 1,125 ± 50 44.291 ± 1.969 1,231 ± 50 48.464 ± 1.969 1,338 ± 50 52.677 ± 1.969 F Net weight 209 8.228 272 10.709 352 13.858 432 17.008 512 20.157 592 23.307 672 26.457 752 29.606 832 32.756 992 39.055 1,152 45.354 1,312 51.653 1,472 57.953 1,632 64.252 1,792 70.551 1,952 76.850 810 g approx. 970 g approx. 1,170 g approx. 1,370 g approx. 1,570 g approx. 1,770 g approx. 1,970 g approx. 2,170 g approx. 2,660 g approx. 3,060 g approx. 3,460 g approx. 3,890 g approx. 4,550 g approx. 4,950 g approx. 5,350 g approx. 5,750 g approx. Standard mounting bracket (Optional) Rear mounting 6 0.236 22.5 0.886 16.5 0.650 3.5 9.5 0.138 0.374 30° 16.5 0.650 22.5 0.88616.5 9.5 0.650 0.374 6 0.236 9.5 30° 0.374 5.3 0.209 4 0.157 8.2 0.323 5.5 0.217 13.5 0.531 18 0.709 28 12 1.102 0.472 9.5 0.374 30° 13.5 16.5 0.531 0.650 3.5 0.138 5.5 0.217 28 1.102 20.5 0.807 t2 t 0.079 8.2 0.323 5.5 0.217 18 0.709 5.5 0.217 20.5 0.807 28 1.102 16.5 0.650 22.5 0.886 9.5 16.5 0.650 0.374 30° 6 0.236 5.3 0.209 4 3.5 13.5 0.531 0.157 0.138 18 3.5 0.709 8.2 0.323 0.138 5.5 0.217 5.5 0.217 9.5 0.374 5 0.197 8.8 0.346 16.5 13.5 0.650 0.531 5.3 0.209 19.3 0.760 10.5 0.413 28 1.102 22.5 0.886 16.5 0.650 t2 t 0.079 30° 20.5 0.807 SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES Selection Guide 8 0.315 Safety Light Curtains t2 t 0.079 Safety Control Units Safety Components SF4B-C SF4C 9.5 0.374 BSF4-AH80 SF2B 9.5 0.374 12 28 30° 0.472 1.102 4 0.157 Four brackets (R type × 2 and L type × 2) per set. M3 (length 5 mm 0.197 in) hexagonsocket-head bolts (eight bolts for safety light curtain mounting, eight bolts for beam axis alignment) are attached. PARTICULAR USE SENSORS SF4B/ SF4B-G 5.5 0.217 18 0.709 8.2 0.323 SF2C 5.5 0.217 3.5 0.138 5 0.197 8.8 0.346 Material: Stainless steel (SUS304) 8 0.315 INDUCTIVE PROXIMITY SENSORS SF4D 6 0.236 3.5 0.138 PRESSURE / FLOW SENSORS 19.3 0.760 Side mounting 28 1.102 12 0.472 30° SAFETY LIGHT CURTAINS / SAFETY COMPONENTS 3.5 0.138 Rear mounting AREA SENSORS UV CURING SYSTEMS 5 0.197 8.8 0.346 10.5 0.413 MICRO PHOTOELECTRIC SENSORS MACHINE VISION SYSTEMS 5.3 0.209 4 0.157 3.5 0.138 8 0.315 PHOTOELECTRIC SENSORS FA COMPONENTS 19.3 5 0.197 0.760 8.8 0.346 10.5 0.413 LASER SENSORS ENERGY MANAGEMENT SOLUTIONS Side mounting 28 1.102 12 0.472 30° FIBER SENSORS 19.3 0.760 8 0.315 28 1.102 10.5 0.413 20.5 0.807 t2 t 0.079 Definition of Sensing Heights 627 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) Dead zoneless mounting bracket (optional) Main body Spacer for intermediate supporting bracket (Accessory) 14 0.551 12 0.472 14 0.551 PRESSURE / FLOW SENSORS 2-M5 5.5 0.217 17 0.669 23 0.906 R32.5 R27.3 25.4° 10° 10° 9.5 0.374 3 0.118 60 2.362 31.5 1.240 14 20 0.551 0.787 1.7 0.067 1.7 0.067 PLC 33 1.299 Mounting adjustment range 10° 10° 6.5 0.256 5.5 0.217 22 0.866 50 1.969 MS-SF2B-2 Intermediate supporting bracket (Accessory for safety light curtain) 5.5 0.217 30 20 1.181 0.787 Selection Guide 6 0.236 6 0.236 8 0.315 18 0.709 18 0.709 8 0.315 8 0.315 6 6 0.236 0.236 17 18 0.669 0.709 10 0.394 18 0.709 6 0.236 4 0.157 26 9.5 0.374 16.5 0.650 1.024 20 30 0.787 1.181 21 0.827 28 1.102 28 1.102 5.5 0.217 5 0.197 10 0.394 15 0.591 t1 t 0.039 12 0.472 5.5 0.217 8 0.315 5.5 0.217 5 0.197 MS-SF2B-4 Adapter mounting bracket for SF1-N / NA40 (Optional) t1 t 0.039 SF4C SF2B 11.5 Material: Stainless steel (SUS304) 0.453 Six brackets set Twelve M5 (length 8 mm 0.315 in) hexagon-socket-head bolts are attached. The adjustment range of the safety light curtain angle is up to ±10 degrees. 67 2.638 3 0.118 FA COMPONENTS BSF4-AH80 t2 t 0.079 50 1.969 22 0.866 54 2.126 ENERGY MANAGEMENT SOLUTIONS 3 0.118 33 1.299 HUMAN MACHINE INTERFACES SF4B-C 16 0.630 54 2.126 14 0.551 40 31.5 20 1.575 1.240 0.787 LASER MARKERS SF4B/ SF4B-G 54 2.126 5.5 0.217 14 0.551 3 0.118 Four bracket set STATIC CONTROL DEVICES SF4D 15 0.591 L-shaped mounting MEASUREMENT SENSORS Safety Components t2 t 0.079 Material: Stainless steel (SUS304) • Die-cast zinc alloy SIMPLE WIRE-SAVING UNITS Safety Control Units 5.5 0.217 20 31 41 56 0.787 1.220 1.614 2.205 9 0.118 M5 hexagonsocket-head bolts 26 27.1 1.024 1.067 15 0.591 30 1.181 36 1.417 51.7 2.035 SENSOR OPTIONS Safety Light Curtains 3 0.118 Center of rotation Angle of movable ranges PARTICULAR USE SENSORS UV CURING SYSTEMS 3 0.118 54 67 31 1.220 2.126 2.638 SAFETY LIGHT CURTAINS / SAFETY COMPONENTS MACHINE VISION SYSTEMS The spacer for intermediate supporting bracket MS-SF2B-2 can be used as a spacer for eliminating the dead zone when mounting the safety light curtain laterally. 3 0.118 AREA SENSORS WIRE-SAVING SYSTEMS The CAD data can be downloaded from our website. MS-SF2B-3 MICRO PHOTOELECTRIC SENSORS INDUCTIVE PROXIMITY SENSORS SF2B SERIES Ver.2 5.5 0.217 4 0.157 18 0.709 5.5 0.217 8.2 0.323 15 0.591 13.8 8 0.315 0.543 t2 t 0.079 30.8 34.8 1.213 1.370 Material: Stainless steel (SUS304) 27 17 1.063 0.669 15 0.591 Material: Stainless steel (SUS304) SF2C 7.7 0.303 Definition of Sensing Heights 3.6 0.142 Two main unit mounting brackets per set (for rear mounting and side mounting) (Note) Note: The intermediate supporting bracket MS-SF2B-2 is enclosed with the following products. The quantity differs depending on the product as shown below: 1 set: S  F2B-H□ ··· 40 to 56 beam channels SF2B-A□ ··· 20 to 28 beam channels 2 sets: SF2B-H□ ··· 64 to 80 beam channels SF2B-A□ ··· 32 to 40 beam channels 3 sets: SF2B-H□ ··· 88 to 96 beam channels SF2B-A□ ··· 44 to 48 beam channels Four bracket set Eight M3 (length 5 mm 0.197 in) hexagon-socket-head bolts are attached. Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) SF2B SERIES Ver.2 628 The CAD data can be downloaded from our website. MS-SF2B-5 Adapter mounting bracket for SF2-A / SF2-N (Optional) Rear mounting Side mounting 28 1.102 12 0.472 22.5 0.886 16.5 0.650 9.5 0.374 30° 30° 16.5 0.650 22.5 0.886 9.5 16.5 0.650 0.374 9.5 30° 0.374 6 0.236 4 0.157 5.3 0.209 13.5 0.531 18 0.709 MICRO PHOTOELECTRIC SENSORS 6 0.236 AREA SENSORS 3.5 0.138 SAFETY LIGHT CURTAINS / SAFETY COMPONENTS 9.5 0.374 28 12 1.102 0.472 30° 13.5 16.5 0.531 0.650 5.3 4 0.209 0.157 3.5 0.138 8.2 0.323 5.5 0.217 5.5 0.217 PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS 18 0.709 PARTICULAR USE SENSORS 5.5 0.217 26.6 1.047 43.25 1.703 8 0.315 8 0.315 t2 t 0.079 10.5 0.413 28 1.102 20.5 0.807 2 0.079 20.5 0.807 LASER MARKERS Rear mounting Side mounting 6 0.236 28 1.102 12 0.472 30° 16.5 0.650 30° 16.5 13.5 0.531 0.650 t2 t 0.079 20.5 0.807 43.25 1.703 10.5 0.413 28 1.102 20.5 0.807 40 1.575 4 0.157 5.5 0.217 32 1.260 19.5 0.768 40.5 1.594 40.5 1.594 Material: Stainless steel (SUS304) 8.4 0.331 13.5 0.531 Four brackets (R type × 2 and L type × 2) per set Eight M3 (length 5 mm 0.197 in) hexagon-socket-head bolts are attached. SF4B/ SF4B-G SF4B-C BSF4-AH80 20.5 0.807 21 15.5 0.827 0.610 32 1.260 19.5 0.768 40.5 1.594 SF2B t2 t 0.079 SF2C 5.5 0.217 40.5 1.594 8.4 0.331 3 (0.118 ) SF4D SF4C 16.5 9.5 0.374 0.650 4 0.157 Safety Control Units Safety Components 2 0.079 28 1.102 20 0.787 16.5 0.650 Selection Guide Safety Light Curtains Adapter mounting bracket for NA40 (Optional) 9.5 0.374 3 (0.118 ) 17 0.669 8 0.315 40 1.575 28 1.102 20 0.787 9 0.354 UV CURING SYSTEMS 5.5 0.217 10.7 0.421 Four brackets (R type × 2 and L type × 2) per set M3 (length 5 mm 0.197 in) hexagonsocket-head bolts (eight bolts for safety light curtain mounting, eight bolts for beam axis alignment) are attached. 21 0.827 MACHINE VISION SYSTEMS 18 0.709 Material: Stainless steel (SUS304) MS-SF2B-6 15.5 0.610 FA COMPONENTS 12 28 30° 0.472 1.102 26.6 1.047 8 0.315 t2 t 0.079 ENERGY MANAGEMENT SOLUTIONS 5.5 0.217 10.7 0.421 20.5 0.807 HUMAN MACHINE INTERFACES 8.2 0.323 5.5 0.217 17 0.669 26.6 43.25 1.047 1.703 10.5 0.413 28 1.102 9.5 0.374 5.3 0.209 4 0.157 4 0.157 5.3 0.209 PLC 22.5 0.886 16.5 0.650 9.5 0.374 30° 3.5 0.138 22.5 9.5 16.5 0.886 0.374 0.650 6 0.236 13.5 0.531 18 0.709 8.2 0.323 5.5 0.217 MEASUREMENT SENSORS STATIC CONTROL DEVICES 3.5 0.138 SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS 10.7 0.421 10.7 0.421 10.5 0.413 28 1.102 SENSOR OPTIONS 17 0.669 17 0.669 26.6 43.25 1.047 1.703 9.5 0.374 LASER SENSORS PHOTOELECTRIC SENSORS 8.2 0.323 5.5 0.217 FIBER SENSORS 9 0.354 13.5 0.531 Definition of Sensing Heights 629 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) Adapter bracket for SF1-N (Optional) 40 1.575 40 1.575 28 1.102 20 0.787 AREA SENSORS 28 1.102 20 0.787 20 0.787 9.5 0.374 4 0.157 PRESSURE / FLOW SENSORS 21 15.5 0.827 0.610 INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS The CAD data can be downloaded from our website. MS-SF2B-7 MICRO PHOTOELECTRIC SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS SF2B SERIES Ver.2 24 0.945 24 0.945 t2 t 0.079 t2 t 0.079 6 0.236 6.5 0.256 32 1.260 31 1.220 9.5 0.374 20 9.5 0.374 0.787 15.5 0.610 6 0.236 6.5 0.256 32 1.260 6.8 0.268 17 0.669 4 0.157 21 0.827 6.8 0.268 17 0.669 31 1.220 17.2 0.677 31 1.220 31 17.2 0.677 1.220 SENSOR OPTIONS 3 (0.118 ) SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS 4 0.157 PLC HUMAN MACHINE INTERFACES FA COMPONENTS 21 0.827 3 (0.118 ) 25 0.984 24 0.945 t2 t 0.079 t2 t 0.079 9 0.354 9 0.354 11 0.433 19 0.748 6.5 0.256 SF2B-CCB□ Safety Control Units Safety Components SF4D Eight M3 (length 5 mm 0.197 in) hexagon-socket-head bolts are attached. 15.5 0.610 Bottom cap cable (Optional) 49.8 ( 1.961 ) Selection Guide 15.5 0.610 21 0.827 3 0.118 ( Material: Stainless steel (SUS304) ) 19 0.748 11 0.433 25 0.984 6.5 0.256 32 1.260 SF2B-CB□ 49.8 ( 1.961 ) (45 1.772) ø6 ø0.236 (8.5 0.335) (8.5 0.335) 15.5 0.610 Bottom cap cable (Optional) L ø6 ø0.236 (8.5 0.335) 4 0.157 (50 1.969) (8 0.315) L Safety Light Curtains 9.5 0.374 16.5 0.650 Four brackets (one of each type) per set 32 1.260 MACHINE VISION SYSTEMS UV CURING SYSTEMS 15.5 0.610 6.5 0.256 40 1.575 28 1.102 20 0.787 24 0.945 16.5 0.650 9.5 0.374 3 (0.118 ) 40 1.575 28 1.102 20 0.787 STATIC CONTROL DEVICES ENERGY MANAGEMENT SOLUTIONS 9 0.354 MEASUREMENT SENSORS LASER MARKERS 6.5 0.256 9 0.354 9.5 0.374 M12 connector (8.5 0.335) (14.5 0.571) (14.5 0.571) SF4B/ SF4B-G L Model No. SF2B-CCB3 3,000 118.110 SF2B-CB05 (-A/B) SF4B-C SF2B-CCB7 7,000 275.590 SF2B-CB5 SF4C BSF4-AH80 SF2B SF2C Definition of Sensing Heights ø14 ( ø0.551 ) Model No. SF2B-CCB10 10,000 393.700 SF2B-CCB15 15,000 590.551 SF2B-CB10 L 500 19.685 5,000 196.850 10,000 393.700 Safety Light Curtain Type 2 DIMENSIONS (Unit: mm in) SFB-CC3  SFB-CC10 ( ) 630 The CAD data can be downloaded from our website. Extension cable (Optional) 42 1.654 SF2B SERIES Ver.2 SFB-CCJ10E  SFB-CCJ10D ( L ø14 ø0.551 42 1.654 ) Extension cable (Optional) ( 10,000 393.700 ) ø14 ø0.551 ø6 ø0.236 Model No. 3,000 118.110 SFB-CC10 10,000 393.700 INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS L SIMPLE WIRE-SAVING UNITS ø6 ø0.236 (8.5 0.335) WIRE-SAVING SYSTEMS MEASUREMENT SENSORS (8.5 0.335) (14.5 0.571) AREA SENSORS PRESSURE / FLOW SENSORS SF2B-CSL01  SF2B-CSL05 Cable for series connection (Optional) 49.8 ( 1.961 ) MICRO PHOTOELECTRIC SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS L SFB-CC3 LASER SENSORS PHOTOELECTRIC SENSORS 47 1.850 ø14 ø0.551 ø6 ø0.236 FIBER SENSORS Model No. L STATIC CONTROL DEVICES SF2B-CSL01 100 3.937 LASER MARKERS SF2B-CSL05 500 19.685 SF-C11 Control unit (Optional) SF-C13 Control unit (Optional) PLC HUMAN MACHINE INTERFACES 6.75 0.266 4 0.157 54.1 2.130 40 1.575 4 0.157 Emitter side connector 25 0.984 35 1.378 67.3 2.650 46 1.811 23 0.906 ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS 130 5.118 UV CURING SYSTEMS 91.6 3.606 3×6=18 0.118×0.236=0.709 130 5.118 6 0.236 10 0.394 13.5 0.531 10 0.394 6 0.236 34.5 3×5=15 1.358 0.118×0.197=0.591 35 1.378 67.3 2.650 11.5 0.453 Receiver side connector 13 0.512 48.8 1.921 5 0.197 6.5 0.256 80 3.150 80.8 3.181 13 0.512 Compatible with 35 mm 1.378 in wide DIN rail 22.5 0.886 5 0.197 Safety Light Curtains 80 3.150 6.5 (100 3.937) 0.256 Compatible with 35 mm 1.378 in wide DIN rail SF-LAT-2B Safety Control Units Safety Components Laser alignment tool (Optional) ( ) 21 22 0.827 0.866 SF-IND-2 Large display unit for safety light curtain (Optional) SF4D 22.8 0.898 18.3 0.720 ø12 ø0.472 38 1.496 28 1.102 66.5 2.618 16.8 0.661 5.3 0.209 48 1.890 SF4B/ SF4B-G SF4B-C SF4C 25 0.984 35.5 40.1 1.398 23 1.579 0.906 4.6 0.181 28 1.102 20 0.787 Selection Guide BSF4-AH80 SF2B 18 1.102 28 1.102 5.5 0.217 ø3.6 ø0.142 Cable, 3m 9.843 ft long 25.4 1.000 t 1.6 t 0.063 6.6 0.260 10.4 0.409 92 3.622 Material: Bracket ··· C  old rolled carbon steel (SPCC)(Black chromate) Enclosure ··· POM Cover ··· Polycarbonate SF2C Definition of Sensing Heights