Amplifier Built-in / U-shaped
Micro Photoelectric Sensor
Ultra-small / Cable type PM-25 SERIES
Compact / Cable type PM-45 SERIES
Compact / Connector built-in type PM-65 SERIES
Conforming to
EMC Directive
PM-25 SERIES
PM-45
SERIES
PM-65
SERIES
Ultimate U-shaped micro photoelectric sensors
One Step Ahead in Performance and Mounting Ease
2015.12
panasonic.net/id/pidsx/global
Certified
(Some models only)
Industry’s First* and Industry’s Top-in-Class*
Advanced Sensors in the Industry.
*
Industry’s first
Three protection circuits standard
on all models
PM-25 SERIES
PM-45 SERIES
PM-65 SERIES
All models are standardly equipped with the following
protection circuits in their compact bodies. These protection
circuits minimize the possibility of sensor malfunctions
caused by erroneous wiring.
1 Reverse supply polarity protection circuit
6 mm 0.236 in
2 Reverse output polarity protection circuit
3 Output short-circuit protection circuit
*
Industry’s first
Industry’s first!
IP64 rating
PM-25 SERIES
PM-45 SERIES
Our original integrated molding method has
eliminated grooves and gaps on the sensing surface
and main body, thus reducing the possibility of
malfunctions caused by splashing water or dust.
No ridges on
sensing surface
No joint seam
*
[Look!]
Large and easy to see
Multi-angle operation indicator
Industry’s
top-in-class
PM-25 SERIES
PM-45 SERIES
PM-65 SERIES
The large operation indicator (orange) lights up when
the beam enters. The indicator is easy to see from
above and from the sides.
PM-45 SERIES
PM-65 SERIES
The sensor unit can be installed with one or
two M3 screws.
■ Models requiring one M3 screw for installation
PM-F25, PM-R25, PM-F65, PM-R65
Compact size
■ Models requiring two M3 screws for installation
Models other than above
PM-45 SERIES
All new models require significantly less mounting space
than our conventional models when mounted with the
same pitch. What's more, the new models can directly
replace our conventional models currently in use.
PM-L45
Conventional
model
(L type)
15.5 0.610
14.6 0.575
26 1.024
10
0.394
26 1.024
18.5 0.728
(Unit: mm in)
2
PM-25 SERIES
* M3 screws and washers are not included.
*
Industry’s
top-in-class
All models easy to
mount with M3 screws
Resistant to vibrations
and impacts
PM-25 SERIES
PM-45 SERIES
PM-65 SERIES
The sections where stress
concentrates, such as the
connecting section of the
cable and internal circuit, are
covered with a resin. This
helps prevent malfunctions
caused by vibrations and
Resin-filled structure
impacts.
(cross-sectional view)
Translate to the Most
* As of November 2015, according to our company’s survey
*
Industry’s first
APPLICATIONS
Ample beam emitting / receiving
distance of 6 mm 0.236 in
PM-25 SERIES
PM-45 SERIES
■ Positioning of a pallet
PM-65 SERIES
The beam emitting and receiving sections are 0.5 mm 0.02 in thinner than
those on our conventional models while their external dimensions are the
same. As a result, the distance between the beam emitting point and
receiving point increased by 1 mm 0.039 in. The wider distance means
less possibility of collision between the sensing section and sensing object.
13.4 0.528
6 0.236
Pallet is stopped by sensing the dog*.
3.7 0.146
■ Sensing the starting point and
overrun of a moving body
Overrun sensing
Dog
(Unit: mm in)
*
Starting point sensing
Overrun
sensing
Beam marks for easy adjustment
Industry’s first
PM-25 SERIES
PM-45 SERIES
Starting point and overrun is
sensed using the dog* on the base.
PM-65 SERIES
The upper-limit and lower-limit positions of beam can be visually
confirmed from the front, back, right and left sides of the sensor unit.
This allows easy adjustment of the position of sensing object.
Upper-limit position
of beam axis
Beam width
Lower-limit position
of beam axis
Beam width marks are provided on
PM25 series and PM45 series.
■ Sensing the starting point on a
rotating body
Starting
point
The starting
point can be
sensed by
making a slit in
the rotating
body.
* “Dog” refers to the sensing object for activating the sensor’s
detecting operation.
< Front / back >
< Right / left >
Sensors come in various shapes to suit a wide range of mounting conditions
■Ultra-small / Cable type
PM-25 SERIES
PM-K25
PM-U25
PM-L25
■Compact / Cable type
PM-K45
■Compact / Connector
built-in type
PM-K65
PM-F25
PM-45 SERIES
PM-T45
PM-L45
PM-T65W
PM-R25
Compact size!
PM-Y45
PM-65 SERIES
PM-T65
Easy mounting with M2 / M3 screws!
PM-F45
PM-R45
Easy connection with a single touch using commercially-available connectors
PM-L65
PM-Y65
PM-F65
PM-F65W
PM-R65
PM-R65W
3
PM
-25
Ultra-small
/ Cable type
PM-25 SERIES
Cable type
NPN output
1 m 3.281 ft
cable
3 m 9.843 ft
cable
1 m 3.281 ft bendingresistant cable
Built-in connector
PNP output
1 m 3.281 ft
cable
3 m 9.843 ft
cable
1 m 3.281 ft bendingresistant cable
PM-K25
PM-L25
PM-U25
PM-F25
Easy mounting with
M2 / M3 screws!
PM-R25
Compact size!
ORDER GUIDE
U type
R type
F type
Ultra-small / Cable type
L type
K type
Type
Appearance (mm in)
6 0.236
12.3
0.484
23.9
0.941
Sensing range
12 0.472
12
0.472
13.4
0.528
6 0.236
16
0.630
13.4
0.528
11.7 0.461
12.5
0.492
13.4
0.528
11.7 0.461
13.4
0.528
12.5
0.492
6 mm 0.236 in
(fixed)
Model No.
Cable length
Output
Output operation
PM-K25
1 m 3.281 ft
PM-K25-R
1 m 3.281 ft,
NPNcommercially-available
open-collector
using
bending-resistant cable transistor
PM-K25-C3
3 m 9.843 ft
PM-K25-P
1 m 3.281 ft
PM-L25
1 m 3.281 ft
PM-L25-R
1 m 3.281 ft,
bending-resistant cable
PM-L25-C3
3 m 9.843 ft
PM-L25-P
1 m 3.281 ft
PM-U25
1 m 3.281 ft
PM-U25-R
1 m 3.281 ft,
bending-resistant cable
PM-U25-C3
3 m 9.843 ft
PM-U25-P
1 m 3.281 ft
PM-F25
1 m 3.281 ft
PM-F25-R
1 m 3.281 ft,
bending-resistant cable
PM-F25-C3
3 m 9.843 ft
PM-F25-P
1 m 3.281 ft
PM-R25
1 m 3.281 ft
PM-R25-R
1 m 3.281 ft,
bending-resistant cable
PM-R25-C3
3 m 9.843 ft
PM-R25-P
1 m 3.281 ft
Easy connection with a single touch
connectors
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
Incorporated with 2 outputs:
Light-ON / Dark-ON
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
Note: The suffix “-R” in the model No. indicates a bending-resistant cable type. The suffix “-C3” indicates a 3 m 9.843 ft cable length type.
OPTIONS
4
Designation
Model No.
Description
Mounting screw
MS-M2
Mounting screw with washers for the ultra-small type sensor
(50 pcs. lot). It can mount securely as it is spring washer
attached.
Mounting screw
•• MS-M2
M2 (length 10 mm 0.394 in)
screw with a spring washer
PM-25
SPECIFICATIONS
Ultra-small / Cable type
Model No.
Type
Item
Bending-resistant cable
3 m 9.843 ft cable
NPN output
PM-□25
PM-□25-R
PM-□25-C3
PNP output
PM-□25-P
―
―
Sensing range
6 mm 0.236 in (fixed)
Minimum sensing object
0.8 × 1.2 mm 0.031 × 0.047 in opaque object
Hysteresis
0.05 mm 0.002 in or less
Repeatability
0.01 mm 0.0004 in or less
Supply voltage
5 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption
15 mA or less
NPN open-collector transistor
•• Maximum sink current: 50 mA
•• Applied voltage: 30 V DC or less (between output and 0 V)
•• Residual voltage: 2 V or less (at 50 mA sink current)
1 V or less (at 16 mA sink current)
Output
Output operation
Incorporated with 2 outputs: Light-ON / Dark-ON
Short-circuit protection
Incorporated
Under light received condition: 20 μs or less
Under light interrupted condition: 80 μs or less
(Maximum response frequency: 3 kHz) (Note 2)
Response time
Operation indicator
Orange LED (lights up under light received condition)
Pollution degree
3
Protection
Environmental resistance
PNP open-collector transistor
•• Maximum source current: 50 mA
•• Applied voltage: 30 V DC or less (between output and + V)
•• Residual voltage: 2 V or less (at 50 mA source current)
1 V or less (at 16 mA source current)
IP64 (IEC)
Ambient temperature
(Note 3, 4)
–25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F
Ambient humidity
5 to 85 % RH, Storage: 5 to 95 % RH
Ambient illuminance
Fluorescent light: 1,000 ℓx at the light-receiving face
Voltage withstandability
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Shock resistance
Emitting element
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Material
Enclosure: PBT, Display section: Polycarbonate
0.09-mm2 4-core cabtyre cable, PVC,
1 m 3.281 ft long
Cable
0.1-mm2 4-core bending-resistant cabtyre
cable, PVC, 1 m 3.281 ft long (Note 5, 6)
0.09-mm2 4-core cabtyre cable, PVC,
3 m 9.843 ft long
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 7)
Cable extension
Weight
Net weight: 10 g approx., Gross weight: 15 g approx.
Net weight: 30 g approx.,
Gross weight: 35 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) The response frequency is the value when the disc, given in the figure below, is rotated.
Disc
1.8 mm 0.071 in
Disc
t = 0.2 mm 0.008 in
1.6 mm 0.063 in
1.6 mm 0.063 in
3) In case the PM-25 series is used at an ambient temperature of +50 °C +122 °F, or more, make sure to mount it on a metal body.
4) Note that the cable of PM-□25-R loses its flexibility when the ambient temperature decreases to about -10 °C +14 F°.
5) The cable of PM-□25-R is a bending-resistant cable usable on a moving base. When the sensor is mounted on a moving base, secure the sensor cable
joint at the unit in place so that stress is not applied to it.
6) When storing PM-□25-R, make sure that the cable does not come into contact with the sensing section or operation indicator.
7) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
5
PM
-45
Compact
/ Cable type
PM-45 SERIES
Cable type
NPN output
1 m 3.281 ft
cable
3 m 9.843 ft
cable
1 m 3.281 ft bendingresistant cable
Built-in connector
PNP output
1 m 3.281 ft
cable
3 m 9.843 ft
cable
1 m 3.281 ft bendingresistant cable
Easy mounting with
M2 / M3 screws!
Compact size!
PM-K45
PM-T45
PM-L45
PM-Y45
PM-F45
PM-R45
Easy connection with a single touch
using commercially-available connectors
ORDER GUIDE
Appearance (mm in)
25.4
1.000
21.3
0.839
13.7 0.539
L type
26
1.024
18.1
0.713
14.6 0.575
26
1.024
7 0.276
6 mm 0.236 in
(fixed)
14.6 0.575
Y type
Compact / Cable type
Sensing range
7 0.276
T type
K type
Type
R type
F type
13.4
0.528
20.6
0.811
13 0.512
13.7
0.539
21.3
0.839
13 0.512
13.7
0.539
21.3
0.839
Model No.
PM-K45
1 m 3.281 ft
PM-K45-C3
3 m 9.843 ft
PM-K45-P
1 m 3.281 ft
PM-K45-P-C3
3 m 9.843 ft
PM-T45
1 m 3.281 ft
PM-T45-C3
3 m 9.843 ft
PM-T45-P
1 m 3.281 ft
PM-T45-P-C3
3 m 9.843 ft
PM-L45
1 m 3.281 ft
PM-L45-C3
3 m 9.843 ft
PM-L45-P
1 m 3.281 ft
PM-L45-P-C3
3 m 9.843 ft
PM-Y45
1 m 3.281 ft
PM-Y45-C3
3 m 9.843 ft
PM-Y45-P
1 m 3.281 ft
PM-Y45-P-C3
3 m 9.843 ft
PM-F45
1 m 3.281 ft
PM-F45-C3
3 m 9.843 ft
PM-F45-P
1 m 3.281 ft
PM-F45-P-C3
3 m 9.843 ft
PM-R45
1 m 3.281 ft
PM-R45-C3
3 m 9.843 ft
PM-R45-P
1 m 3.281 ft
PM-R45-P-C3
3 m 9.843 ft
Note: The suffix “-C3” in the model No. indicates a 3 m 9.843 ft cable length type.
6
Cable length
Output
Output operation
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
NPN open-collector
transistor
PNP open-collector
transistor
Incorporated with 2 outputs:
Light-ON / Dark-ON
PM-45
SPECIFICATIONS
Compact / Cable type
Model No.
Type
Item
3 m 9.843 ft cable
NPN output
PM-□45
PM-□45-C3
PNP output
PM-□45-P
PM-□45-P-C3
Sensing range
6 mm 0.236 in (fixed)
Minimum sensing object
0.8 × 1.2 mm 0.031 × 0.047 in opaque object
Hysteresis
0.05 mm 0.002 in or less
Repeatability
0.01 mm 0.0004 in or less
Supply voltage
5 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption
15 mA or less
NPN open-collector transistor
•• Maximum sink current: 50 mA
•• Applied voltage: 30 V DC or less (between output and 0 V)
•• Residual voltage: 2 V or less (at 50 mA sink current)
1 V or less (at 16 mA sink current)
Output
Output operation
Incorporated with 2 outputs: Light-ON / Dark-ON
Short-circuit protection
Incorporated
Under light received condition: 20 μs or less
Under light interrupted condition: 80 μs or less
(Maximum response frequency: 3 kHz) (Note 2)
Response time
Operation indicator
Orange LED (lights up under light received condition)
Pollution degree
3
Protection
Environmental resistance
PNP open-collector transistor
•• Maximum source current: 50 mA
•• Applied voltage: 30 V DC or less (between output and + V)
•• Residual voltage: 2 V or less (at 50 mA source current)
1 V or less (at 16 mA source current)
IP64 (IEC)
Ambient temperature
–25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F
Ambient humidity
5 to 85 % RH, Storage: 5 to 95 % RH
Ambient illuminance
Fluorescent light: 1,000 ℓx at the light-receiving face
Voltage withstandability
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Shock resistance
Emitting element
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Material
Enclosure: PBT, Display section: Polycarbonate
2
0.09-mm 4-core cabtyre cable, PVC, 1 m 3.281 ft long
Cable
0.09-mm2 4-core cabtyre cable, PVC, 3 m 9.843 ft long
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 3)
Cable extension
Weight
Net weight: 10 g approx., Gross weight: 15 g approx.
Net weight: 30 g approx., Gross weight: 35 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) The response frequency is the value when the disc, given in the figure below, is rotated.
Disc
Disc
1.8 mm 0.071 in
t = 0.2 mm 0.008 in
1.6 mm 0.063 in
1.6 mm 0.063 in
3) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
7
Compact size!
PM
-65
Compact
/ Connector built-in type
Cable type
NPN output
Connector attached cable
1 m 3.281 ft, 2 m 6.562 ft,
3 m 9.843 ft, 5 m 16.404 ft
Connector attached bending-resistant cable
1 m 3.281 ft, 2 m 6.562 ft,
3 m 9.843 ft, 5 m 16.404 ft
PNP output
Connector attached cable
1 m 3.281 ft, 2 m 6.562 ft,
3 m 9.843 ft, 5 m 16.404 ft
Connector attached bending-resistant cable
1 m 3.281 ft, 2 m 6.562 ft,
3 m 9.843 ft, 5 m 16.404 ft
Built-in connector
PM-K65
PM-65 SERIES
PM-T65
PM-T65W
PM-L65
PM-Y65
Easy connection with a single touch
using commercially-available connectors
PM-F65
PM-F65W
PM-R65
PM-R65W
ORDER GUIDE
K type
Type
Appearance (mm in)
22.4
0.882
26
1.024
Sensing range
T type
22.4
0.882
22.4
0.882
16.7 0.657
L type
NPN open-collector
transistor
PM-K65-P
PNP open-collector
transistor
PM-T65
NPN open-collector
transistor
PM-T65-P
PNP open-collector
transistor
PM-T65W
NPN open-collector
transistor
PM-T65W-P
PNP open-collector
transistor
PM-L65
NPN open-collector
transistor
PM-L65-P
PNP open-collector
transistor
PM-Y65
NPN open-collector
transistor
PM-Y65-P
PNP open-collector
transistor
PM-F65
NPN open-collector
transistor
PM-F65-P
PNP open-collector
transistor
PM-F65W
NPN open-collector
transistor
PM-F65W-P
PNP open-collector
transistor
PM-R65
NPN open-collector
transistor
PM-R65-P
PNP open-collector
transistor
PM-R65W
NPN open-collector
transistor
PM-R65W-P
PNP open-collector
transistor
14.9 0.587
26.2
1.031
15.7
0.618
Y type
14.9 0.587
6 mm 0.236 in (fixed)
13.4
0.528
13.5 0.531
F type
Compact / Connector built-in type
26
1.024
Output
PM-K65
7 0.276
13.7 0.539
26
1.024
Model No.
13.4
0.528
22.7
0.894
22.4
0.882
Output operation
Incorporated with 2 outputs:
Light-ON / Dark-ON
13 0.512
13.4
0.528
22.4
0.882
R type
13.5 0.531
13.4
0.528
22.4
0.882
13 0.512
13.4
0.528
22.4
0.882
Note: “W” in the model No. indicates that the product is mounting-compatible with our conventional models [PM-T53(B) / PM-□64(P)].
8
PM-65
OPTIONS
Designation
Model No.
Connector
attached cable
Connector
attached cable
Bendingresistant cable
CN-14A-C1
Length: 1m 3.281 ft
CN-14A-C2
Length: 2m 6.562 ft
CN-14A-C3
Length: 3m 9.843 ft
CN-14A-C5
Length: 5m 16.404 ft
CN-14A-R-C1
Length: 1m 3.281 ft
CN-14A-R-C2
Length: 2m 6.562 ft
CN-14A-R-C3
Length: 3m 9.843 ft
CN-14A-R-C5
Length: 5m 16.404 ft
CN-14A
Connector
Connector attached cable
Description
•• CN-14A(-R)-C□
0.2 mm2 4-core cabtyre cable with
connector on one end
Cable outer diameter: ø3.7 mm
ø0.146 in
0.2 mm2 4-core cabtyre cable with
connector on one end
Cable outer diameter: ø3.7 mm
ø0.146 in
Connector
•• CN-14A
Contact
4
Set of 10 housings and 40 contacts
Housing
SPECIFICATIONS
Compact / Connector built-in type
Model No.
Type
Item
Mounting-compatible with conventional model (Note 2)
NPN output
PM-□65
PM-□65W
PNP output
PM-□65-P
PM-□65W-P
Sensing range
6 mm 0.236 in (fixed)
Minimum sensing object
0.8 × 1.2 mm 0.031 × 0.047 in opaque object
Hysteresis
0.05 mm 0.002 in or less
Repeatability
0.01 mm 0.0004 in or less
Supply voltage
5 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption
Output
15 mA or less
NPN open-collector transistor
•• Maximum sink current: 50 mA
•• Applied voltage: 30 V DC or less (between output and 0 V)
•• Residual voltage: 2 V or less (at 50 mA sink current)
1 V or less (at 16 mA sink current)
Output operation
Incorporated with 2 outputs: Light-ON / Dark-ON
Short-circuit protection
Response time
Incorporated
Under light received condition: 20 μs or less, Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz) (Note 3)
Operation indicator
Orange LED (lights up under light received condition)
Pollution degree
3
Protection
Environmental resistance
PNP open-collector transistor
•• Maximum source current: 50 mA
•• Applied voltage: 30 V DC or less (between output and + V)
•• Residual voltage: 2 V or less (at 50 mA source current)
1 V or less (at 16 mA source current)
IP40 (IEC)
Ambient temperature
–25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F
Ambient humidity
5 to 85 % RH, Storage: 5 to 95 % RH
Ambient illuminance
Fluorescent light: 1,000 ℓx at the light-receiving face
Voltage withstandability
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Shock resistance
Emitting element
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Material
Enclosure: PBT, Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 4)
Cable length
Weight
Net weight: 3 g approx., Gross weight: 3 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the
conditions used were an ambient temperature of +23 °C +73.4 °F.
2) Mounting-compatible with our conventional models [PM-T53(B) / PM-□64(P)]
3) The response frequency is the value when the disc, given in the figure
below, is rotated.
Disc
1.8 mm 0.071 in
Disc
Recommended connector
Contact: SPHD-001T-P0.5, Housing: PAP-04V-S
(Manufactured by J.S.T. Mfg. Co., Ltd.)
Note: Contact the manufacturer for details of the recommended products.
Recommended crimping tool
Model No. : YC-610R (Manufactured by J.S.T. Mfg. Co., Ltd.)
Note: Contact the manufacturer for details of the recommended products.
t = 0.2 mm 0.008 in
1.6 mm 0.063 in
1.6 mm 0.063 in
4) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply
voltage at the end of the cable attached to the sensor is 4.5 V or higher.
9
PM-25 PM-45 PM-65
I/O CIRCUIT AND WIRING DIAGRAMS
NPN output type
I/O circuit diagram
Wiring diagram (PM-25 series / PM-45 series)
Color of cable type lead wire or color of
lead wire of connector attached cable
Brown
Load
Black (Note)
Sensor circuit
(Brown) +V
ZD1
ZD2
Tr2
(Black) Output 1
(Note)
Load
50 mA max.
(White) Output 2 (Note)
T r1
D
(Blue) 0 V
Load
+
–
Load
50 mA max.
+
–
White (Note)
5 to 24 V DC
±10 %
5 to 24 V DC
±10 %
Blue
Note: Ensure to insulate the unused output wire.
Internal circuit
Users’ circuit
Output operation
Note: Ensure to insulate the unused output wire.
Symbols…D: Reverse supply polarity protection diode
ZD1, ZD2: Surge absorption zener diode
Tr1, Tr2: NPN output transistor
Color code
Output operation
Output 1
Black
Light-ON
Output 2
White
Dark-ON
Terminal arrangement diagram (PM-65 series)
1
2
3
4
Terminal No.
Designation
1
+V
2
Output 1: Light-ON
3
Output 2: Dark-ON
4
0V
PNP output type
Wiring diagram (PM-25 series / PM-45 series)
I/O circuit diagram
Color of cable type lead wire or color of
lead wire of connector attached cable
Sensor circuit
D
(Brown) +V
Tr1
Tr2
ZD1
ZD2
Brown
Black (Note)
+
50 mA max.
(Black) Output 1 (Note)
50 mA max.
(White) Output 2 (Note)
Load
(Blue) 0 V
+
Load
–
White (Note)
5 to 24 V DC
±10 %
Load
–
5 to 24 V DC
±10 %
Load
Blue
Note: Ensure to insulate the unused output wire.
Internal circuit
Users’ circuit
Note: Ensure to insulate the unused output wire.
Symbols…D: Reverse supply polarity protection diode
ZD1, ZD2: Surge absorption zener diode
Tr1, Tr2: PNP output transistor
Output operation
Color code
Output operation
Output 1
Black
Light-ON
Output 2
White
Dark-ON
Terminal arrangement diagram (PM-65 series)
1
10
2
3
4
Terminal No.
Designation
1
+V
2
Output 1: Light-ON
3
Output 2: Dark-ON
4
0V
PM-25 PM-45 PM-65
SENSING CHARACTERISTICS (TYPICAL)
PM-25 series
PM-45 series
Sensing position
Sensing position
DarkON
DarkON
DarkON
5.5 mm
0.217 in
DarkON
8.4 mm
0.331 in
6 mm
0.236 in
ℓ
ℓ
Beam
axis
0
ℓ
2 mm
0.079 in
2 mm
0.079 in
LightON
7 mm
0.276 in
ℓ
1
2
3
0.039
0.079
0.118
Operating point ℓ (mm in)
4
0.157
LightON
0
1
2
3
0.039
0.079
0.118
Operating point ℓ (mm in)
4
0.157
LightON
Beam
axis
0
1
2
3
0.039
0.079
0.118
Operating point ℓ (mm in)
4
0.157
LightON
0
1
2
3
0.039
0.079
0.118
Operating point ℓ (mm in)
4
0.157
PM-65 series
Sensing position
DarkON
DarkON
8.4 mm
0.331 in
7 mm
0.276 in
ℓ
ℓ
2 mm
0.079 in
LightON
Beam
axis
0
1
2
3
0.039
0.079
0.118
Operating point ℓ (mm in)
4
0.157
LightON
0
1
2
3
0.039
0.079
0.118
Operating point ℓ (mm in)
4
0.157
PRECAUTIONS FOR PROPER USE
••Never use this product as a sensing device
for personnel protection.
••In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
PM-45 series
••The following conditions must be observed when using
screws to mount the sensor unit.
Screw
M3 screw
Spring washer
Flat washer
Tightening torque
1 pc.
ø6 mm ø0.236 in
(small round washer)
0.5 N·m
M3 screws
Spring washer
Mounting
Plain washer
Outer diameter
ø6 mm ø0.236 in
PM-25 series
••The following conditions must be observed when using
screws to mount the sensor unit.
Screw
M2 screw
M3 screw
Spring washer
Flat washer
Tightening torque
1 pc.
ø4.3 mm ø0.169 in
(small round washer)
0.15 N·m
1 pc.
ø6 mm ø0.236 in
(small round washer)
0.5 N·m
< When using M2 screws for mounting > < When using M3 screws for mounting >
M2 screws
Spring washer
Plain washer
Outer diameter
ø4.3 mm ø0.169 in
M3 screws
Spring washer
Plain washer
Outer diameter
ø6 mm ø0.236 in
When using the optional mounting screw set MS-M2, a
spring washer is included.
••In case the PM-25 series is used at an ambient
temperature of +50 °C +122 °F, or more, make sure to
mount it on a metal body.
PM-65 series
••The following conditions must be observed when using
screws to mount the sensor unit.
Screw
M3 screw
Spring washer
Flat washer
Tightening torque
1 pc.
ø6 mm ø0.236 in
(small round washer)
0.5 N·m
M3 screws
Spring washer
Plain washer
Outer diameter
ø6 mm ø0.236 in
11
PM-25 PM-45 PM-65
PRECAUTIONS FOR PROPER USE
Cable extension
Wiring (PM-65 series)
PM-25 series / PM-45 series
••Cable extension is possible up to an overall length
of 100 m 328.084 ft with a 0.3 mm2, or more, cable.
However, since a voltage drop shall occur due to the cable
extension, ensure that the power supply voltage at the
end of the cable attached to the sensor is within the rating.
Connection method
••Insert the connector attached cable CN‑14A-C□ /
CN‑14A-R-C□ in the connector part of this product as
shown in the figure below.
Lock release lever
Total cable length 100 m 328.084 ft
CN-14A-C□ / CN-14A-R-C□
Cable attached
to sensor
+V
Extension cable
Output
+
5 to 24 V DC
±10 %
–
0V
Housing: PAP-04V-S
(Manufactured by J.S.T. Mfg. Co., Ltd.)
Supply voltage: 4.5 V or more
But, when the overall cable length, including the cable
attached to the sensor, is as given below, there is no
need to confirm the voltage.
Conductor crosssection
area of extension cable
0.08 to 0.1 mm2
Total cable length
Up to 5 m 16.404 ft
2
0.2 mm
Up to 10 m 32.808 ft
0.3 mm2
Up to 20 m 65.617 ft
Output
+
0V
–
5 to 24 V DC
±10 %
Supply voltage: 4.5 V or more
But, when the overall cable length, including the cable
attached to the sensor, is as given below, there is no
need to confirm the voltage.
Conductor crosssection
area of extension cable
0.08 to 0.1 mm2
12
Total cable length
Up to 5 m 16.404 ft
2
0.2 mm
Up to 10 m 32.808 ft
0.3 mm2
Up to 20 m 65.617 ft
+V
Output 1 Output 2
0V
Disconnection method
••Press and hold the lock release lever to disconnect the
cable connector.
Note: Pulling the cable without pressing the lock release lever in an attempt
to disconnect the connector can cause wire breakage in the cable or
damage to the connector.
PM-65 series
••Cable extension is possible up to an overall length
of 100 m 328.084 ft with a 0.3 mm2, or more, cable.
However, since a voltage drop shall occur due to the
cable extension, ensure that the power supply voltage at
the end of the connector attached cable of the sensor or
at the sensor terminals is within the rating.
Total cable length 100 m 328.084 ft
Connector
+V
attached cable
Extension cable
Connector pin No.
Terminal designation
When using the product as an S-mark compatible
product in Korea
••The power supply cable and output cable connected to the
product must be less than 10 m 32.808 ft.
Other
••This device has been developed / produced for industrial
use only.
••Since the sensor is intended for
use inside machines, no special
countermeasures have been taken
against extraneous light. Take care
that extraneous light is not directly
incident on the beam receiving section.
••Do not use during the initial transient time (50 ms) after
the power supply is switched on.
••Note that the cable of PM-□25-R loses its flexibility when
the ambient temperature decreases to about -10 °C +14 °F.
••The cable of PM-□25-R is a bending-resistant cable
usable on a moving base. When the sensor is mounted
on a moving base, secure the sensor cable joint at the
unit in place so that stress is not applied to it.
••When storing PM-□25-R, make sure that the cable
does not come into contact with the sensing section or
operation indicator.
••If the sensor is used in a place having excessive dust,
periodically clean the emitting and receiving sections with
a dry, soft cloth.
••If there is a large surge generating equipment, such as,
motor, solenoid, electromagnetic valve, etc., in the vicinity
of the sensor, use a surge absorber on that equipment.
Further, do not run the sensor cables along power lines
and use a capacitor between +V and 0 V, if required.
Use the sensor after confirming that the surge has been
eliminated.
PM-25 PM-45 PM-65
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
PM-K25□
Sensor
Operation indicator (Orange)
23.9
0.941
18.7
0.736
13.4
0.528
6
0.236
1.7
0.067
1.75
0.069
2–elongated mounting holes
Beam
axis
12 6
0.472 0.236
Operation indicator
(Orange)
8
0.315
6
0.236
2 0.079
5.5 Beam
12.3 0.217 axis
0.484
5.5 Beam
0.217 axis
5 0.197
2-ø3.2 ø0.126
mounting holes
ø6
ø0.236
13.4
0.528
6
0.236
Beam size:
1.2 × 0.8 0.047 × 0.031
8 0.315
Sensor
Operation indicator (Orange)
3
0.118
3 0.118
6 Beam
0.236 axis
PM-L25□
1.6
0.063
3.2
0.126
Operation indicator (Orange)
2
0.079
6
0.236
Beam size:
1.2 × 0.8 0.047 × 0.031
10 12
0.394 0.472
4 0.157
ø2.5 ø0.098 cable, 1 m 3.281 ft long
2
0.079
ø2.5 ø0.098 cable, 1 m 3.281 ft long
PM-K25(-P)
PM-L25(-P)
PM-U25□
Sensor
PM-F25□
Sensor
Operation indicator (Orange)
6 3 0.118
0.236
6 Beam
0.236 axis
Beam
axis
13.4
0.528
6
0.236
Operation indicator (Orange)
2 0.079
5.5 Beam
0.217 axis
11.5
0.453
16
0.630
2-ø3.2 ø0.126
mounting holes
Operation indicator (Orange)
Beam size:
1.2 × 0.8 0.047 × 0.031
3
0.118
11.7
0.461
6.2
0.244
1.6
0.063
Elongated
mounting hole
1.95 0.077
8
0.315
PM-U25(-P)
12.5 12 8 0.315
0.492 0.472
5
3.2 0.126 0.197
ø2
ø0.079
ø2.5 ø0.098 cable,
1 m 3.281 ft long
Beam size:
1.2 × 0.8 0.047 × 0.031 1.5 0.059
(2 0.079)
R1.6
R0.063
ø2.5 ø0.098 cable,
1 m 3.281 ft long
4
0.157
6.7
0.264
13.4
0.528
6
0.236
Operation indicator
(Orange)
Beam 5.5
axis 0.217
2
0.079
ø4.8
ø0.189
PM-F25(-P)
PM-R25□
Sensor
Beam 6
axis 0.236
Operation indicator
(Orange)
4
0.157
6.7
0.264
Operation indicator
(Orange)
5.5 Beam
0.217 axis
2 0.079
13.4
0.528
6
0.236
Beam size:
1.5
0.059 1.2 × 0.8 0.047 × 0.031
R1.6
(2 0.079)
R0.063
12
8 0.315 0.472 12.5
0.492
ø2.5 ø0.098 cable,
1 m 3.281 ft long
ø4.8
ø0.189
5 3.2
Elongated
mounting hole
1.6 0.063
11.7
0.461
6.2
0.244
3
0.118
ø2
ø0.079
1.95 0.077
PM-R25(-P)
13
PM-25 PM-45 PM-65
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
PM-K45□
Sensor
25.4
1.000
19
0.748
PM-T45□
Sensor
Operation indicator (Orange)
3.5
0.138
7
0.276
Operation indicator (Orange)
2-ø3.2 ø0.126
mounting holes
19
0.748
13.4
0.528
6
0.236
Operation indicator
(Orange)
2-ø3.8 ø0.150
mounting holes
26 1.024
6
Beam size:
1.2 × 0.8 0.047 × 0.031 0.236
2
0.079
19 0.748
6
0.236
8.4 0.331
3.2 0.126
Operation indicator
(R)
(Orange)
4.3
0.169 ø2.5 ø0.098 cable,
1 m 3.281 ft long
0.244
5.5
0.217
13.7
0.539
13.4
0.528
2
0.079
Beam
axis
15.2
0.598
13
17.2
18.1 0.677 0.512
0.713
6.2
Beam
axis
13.8
0.543
8.4 0.331
17.2
21.3 0.677
0.839
11 0.433
Beam size:
1.2 × 0.8 0.047 × 0.031
2–elongated
mounting holes
ø2.5 ø0.098 cable,
1 m 3.281 ft long
2.5
0.098
PM-T45
PM-K45
PM-L45□
Sensor
26 1.024
3.5 0.138
10 7 0.276 3.2 0.126
0.394
Sensor
3.5
0.138
Operation indicator (Orange)
19 0.748
7
0.276
7.5 0.295
7 0.276
Operation indicator (Orange)
ø2.5 ø0.098 cable,
1 m 3.281 ft long
5 0.197
ø2.5 ø0.098 cable,
1 m 3.281 ft long
1.5
0.059
19 0.748
13.4
0.528
6
0.236
2-ø3.2 ø0.126
mounting holes
14.6
0.575
Operation indicator (Orange)
6
2 Beam size:
0.079 1.2 × 0.8 0.047 × 0.031 0.236
Beam
axis
9
0.354 12.6
0.496
8.4 0.331
7.2 0.283
2-ø3.5 ø0.138 mounting holes
20.6 6
0.811 0.236
2–elongated mounting holes
4
0.157
PM-Y45□
4.5
0.177
13.4
0.528
6
0.236
14.6
0.575
2 0.079
8.4 0.331
Beam size:
1.2 × 0.8 0.047 × 0.031
2
0.079
Beam
axis
12.6
0.496
4.5
0.177
2.5
0.098
Operation indicator (Orange)
2
0.079
PM-L45
PM-F45□
Sensor
PM-R45□
Sensor
PM-Y45
Operation indicator (Orange)
Operation indicator
(Orange)
8.4 0.331
13.6
0.535
2.5 0.098
13.7
0.539
13.4
0.528
6
0.236
Beam size:
1.2 × 0.8 0.047 × 0.031
2
0.079
Beam
axis
15.2
0.598
9 0.354
7
0.276
2-ø3.5 ø0.138
mounting holes
ø2.5 ø0.098 cable,
1 m 3.281 ft long
Operation indicator
(Orange)
13
0.512
7
0.276
6 0.236
17.2
0.677 21.3
0.839
Beam size:
1.2 × 0.8 0.047 × 0.031
6 0.236
17.2
21.3 0.677
0.839
13
0.512
7
0.276
13.7
2
0.079
9 0.354
7
0.276
Beam
axis
15.2
0.598
2-ø3.5 ø0.138
mounting holes
ø2.5 ø0.098 cable,
1 m 3.281 ft long
PM-R45
PM-F45
14
13.4
6
Operation indicator
(Orange)
8.4 0.331
13.6
0.535
2.5 0.098
PM-25 PM-45 PM-65
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
PM-K65 PM-K65-P
Sensor
PM-T65 PM-T65-P
Sensor
Operation indicator (Orange)
26 1.024
20 0.787
6.5
0.256
Beam size:
1.2 × 0.8 0.047 × 0.031
26 1.024
20 0.787
6
7
0.276 0.236
Beam
axis
4.1
0.161
2
0.079
Beam
8.4 0.331 axis
22.4
3.2 0.126
0.882
7.4 0.291
Operation indicator (Orange)
22.4
0.882
13.8
0.543
8.3
0.327
3.7 0.146
8.4
0.331
Operation indicator (Orange)
7
0.276
Beam
axis
Sensor
4.1 0.161
1.6 0.063
26 1.024
20 0.787
6.5
0.256
PM-L65 PM-L65-P
13 0.512
Beam size:
1.2 × 0.8 0.047 × 0.031
6
0.236
26.2 1.031
20 0.787
3.9 0.154
1.7 0.067
Beam axis
4 0.157
Beam axis
Operation indicator
(Orange)
10
0.394
Beam
axis
2–mounting
holes
14.9
0.587
Sensor
13.4
0.528
6
0.236
8.4 0.331
6.5
0.256
Beam
axis
9 0.354
12.9 0.508
Operation indicator (Orange)
7.2 0.283
20 0.787
Operation indicator
(Orange)
PM-T65W(-P)
Beam size:
1.2 × 0.8 0.047 × 0.031
7
6
15.7 0.276 0.236
0.618
3.2
0.126
(2 0.079)
6 13.4
0.236 0.528
Sensor
Operation indicator (Orange)
2–elongated
mounting holes
7.4 0.291
6
0.236
(2 0.079)
3
0.118
PM-T65(-P)
PM-T65W PM-T65W-P
PM-Y65 PM-Y65-P
Beam
axis
2
0.079
13.4
0.528
PM-K65(-P)
7.4
0.291
14
0.551
Beam size: 1.2 × 0.8 0.047 × 0.031
6
0.236
Operation indicator (Orange)
13.7
0.539
2–mounting holes
2 0.079
3.7 0.146
20 0.787
2.3 0.091
13
0.512
1.6 0.063
13.4
0.528
6
0.236
16.7
0.657
7.4 0.291
6.2 3.2 0.126
0.244
3.5 0.138
2-ø3.2 ø0.126 mounting holes
22.4 0.882
8.4
8.3
0.331
0.327
2–elongated mounting holes
2-ø3.2 ø0.126 mounting holes
26.2 1.031
PM-F65 PM-F65-P
Operation indicator (Orange)
2-ø3.5 ø0.138
mounting holes
7
0.276
Operation indicator (Orange)
6.5 0.256 6 0.236
2.5 0.098
3.5 0.138
7
0.276
22.7 Beam
0.894 axis
6
0.236
3 0.118
Beam size:
1.2 × 0.8 0.047 × 0.031
Beam
14.9 8.4 0.331 axis
0.587
2
0.079
6.5
0.256
ø2.4 ø0.094
16.3
0.642
Beam
axis
8.3
7.7
0.303 0.327
4.1 0.161
PM-Y65(-P)
2.5
0.098
Beam size:
1.2 × 0.8 0.047 × 0.031
13.4
0.528
6
(2 0.079)
0.236
8.4
3.2
0.331
0.126
3.7 2.1
22.4
0.146 0.083 0.882
Operation indicator (Orange)
12.9
0.508
Beam
axis
3
0.118
Operation indicator (Orange)
13.4
0.528
6
0.236
Sensor
PM-L65(-P)
7
0.276
13.5
0.531
Elongated mounting hole
PM-F65(-P)
15
PM-25 PM-45 PM-65
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
PM-F65W PM-F65W-P
13.7
0.539
7
0.276
Sensor
Beam
axis
3
0.118
6
6.5
0.236 0.256
Beam
axis
13
0.512
7
0.276
Beam size:
1.2 × 0.8 0.047 × 0.031
13.4
0.528
6
0.236
Sensor
Operation indicator (Orange)
Operation indicator (Orange)
Beam
axis
2.5 0.098
PM-R65 PM-R65-P
Operation indicator
(Orange)
6 0.236
(2 0.079)
2-ø3.5 ø0.138
mounting holes
22.4
0.882
8.3 0.327
3
0.118
Beam size:
1.2 × 0.8 0.047 × 0.031
6.5 0.256
(2 0.079)
9 0.354
13.6 7
0.535 0.276
13.4
0.528
6
0.236
Beam
axis
11.4
0.449
Operation indicator (Orange)
ø2.4
ø0.094
2.5 0.098
8.4 0.331
22.4
0.882
3.2
0.126
16.3
0.642
3.7 0.146
8.3 0.327 7.7 0.303
2.1
0.083
PM-F65W(-P)
4.1 0.161
7
0.276
13.5
0.531
Elongated
mounting hole
PM-R65(-P)
PM-R65W PM-R65W-P
Sensor
Operation indicator (Orange)
6.5 0.256
6 0.236
(2 0.079)
13
0.512
7
0.276
L
13.7
0.539
7
0.276
35
1.378
Beam size:
1.2 × 0.8 0.047 × 0.031
Operation indicator (Orange)
2-ø3.5 ø0.138
mounting holes
7 0.276 13.6
0.535
13.4
0.528
6
0.236
50
1.969
8
0.315
8
0.315
Beam
axis
9 0.354
11.4
0.449
CN-14A-C□ CN-14A-R-C□ Connector attached cable (Optional)
2.5 0.098
ø3.7 ø0.146 cable
Beam
axis
•• Length L
22.4
0.882
8.3 0.327
Model No.
Length L
CN-14A(-R)-C1
1,000 39.370
CN-14A(-R)-C2
2,000 78.740
CN-14A(-R)-C3
3,000 118.110
CN-14A(-R)-C5
5,000 196.850
PM-R65W(-P)
Disclaimer
The applications described in the catalog are all intended for examples only. The purchase of our products described in the catalog shall not be regarded as
granting of a license to use our products in the described applications. We do NOT warrant that we have obtained some intellectual properties, such as patent
rights, with respect to such applications, or that the described applications may not infringe any intellectual property rights, such as patent rights, of a third party.
Please contact:
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Global Sales Department
■Telephone: +81-568-33-7861 ■Facsimile: +81-568-33-8591
panasonic.net/id/pidsx/global
All Rights Reserved ©
No.CE-PM254565-12 December, 2015
Specifications are subject to change without notice.
2015
Printed in Japan